Citizen | C460 | Citizen Movement/Cal

Citizen Movement/Cal. C460
Abbreviated Instructions
FEATURES
BENEFITS
„30 Cities/ 22 Time Zones
„Analog and Digital Display
„Calendar
„2 Alarms
„24 Hour, 1/100 Second Chronograph
„99 Minute Countdown Timer
„Dual Time
„Electro-luminescence
„Worldwide Time
„Time at a Glance
„Perpetual for 100 years
„Use Alarm 2 for Snooze
„Split-Second Precise Timing
„Sounds Signal When Time is Up
„See Two Time Zones
„Time Visible at Night
Click Here for Full Setting Instructions (176k pdf)
NOTE: After a battery change or an abnormal
„Press and release the lower left button (B).
TO USE THE CHRONOGRAPH
display or function is noticed, an ALL RESET
Hours will flash.
„Press upper left button (M) to move to
is required. Be sure to set the time and date
„Press the lower right button (A) to set hours
CHR mode. The chronograph can measure
after performing the ALL RESET.
according to a.m. or p.m.
up to 23 hour, 59 minutes, 59 and 99/100
ALL RESET PROCEDURE
„Press the lower left button (B). 12H will flash.
seconds.
„Press and release the upper left button (M) to
Press the lower right button (A) to select 24H
„Press the lower right button (A) to start or
move mode indicator to TME (time) mode.
(military time) if desired.
stop chronograph. Digital display I shows
„Pull the crown out to setting position.
„Press the lower left button (B) or the upper
minutes, seconds and 1/100 seconds.
„Press the upper left (M), lower left(B) and lower
left button ( M) to return to normal time display.
Digital display Il shows measured time
right(A) buttons down simultaneously for 3
TO SET THE CALENDAR
hours.
seconds, then release them. All digital segments
„Press and release the upper left button (M)
„If the lower left button (B) is pressed while
in the displays will be highlighted (black).
to move mode indicator to CAL (calendar).
chronograph is running, a split time is
„Press crown in. At this point, a beep is heard
Digital display I shows Month and Date.
displayed for 10 seconds as chronograph
indicating that ALL RESET is complete. Set
Digital display II shows City Code.
continues counting elapsed time internally.
correct time and calendar and other modes as
„Hold the lower left button (B) in for three
„If the lower left button (B) is pressed when
needed.
seconds and then release. Month number
counting is stopped, chronograph is reset to
TO SET THE ANALOG TIME
starts flashing. Press the lower right button (A)
zero.
„Pull crown out to hand setting position and turn
to advance month number.
TO USE THE TIMER
crown.
„Press and release lower left button (B). Date
„Press the upper left button (M) to move to
TO SWITCH DIGITAL MODES
starts flashing. Press the lower right button (A)
TMR (Timer mode). Timer can be set to
„Modes can be changed in the following
to advance date.
countdown from 99 minutes down to 1
sequence: TME (time), CAL (calendar), AL-1 and
„Press and release the lower left button (B).
minute in 1-minute intervals. Digital display
AL-2 (alarms), CHR (chronograph), TMR (timer),
Digital display I shows the year and year
ll shows Timer set time in minutes and
SET (zone setting) by pushing and releasing the
numbers will be flashing. Press the lower right
digital display I shows Timer minutes and
Mode (M) button.
button (A) to advance year.
seconds remaining.
TO SET THE DIGITAL TIME
„After the lower left button (B) or upper left
„Press lower left button (B) to set Timer
„Press the lower left button (B) to move the time
button ( M) is pressed, digital display l shows
minutes.
zone city code into digital display II.
month (numeric) and date.
„Press lower right button (A) to start or stop
„If TME is not showing in digital mode display,
TO SET ALARMS (ALM 1 & 2 )
Timer countdown.
press the upper left button (M) button to select
„Pressing the upper left button (M), move the
„Pressing lower left button (B) after Timer
TME.
mode indicator to ALM 1 (or ALM 2).
is stopped resets it to original Timer set
„Press the lower left button (B) in and hold for 3
„Press and hold the lower left button (B) for 3
time.
seconds to switch to digital time setting mode.
seconds then release it. The hours in digital
„If the lower left button (B) is pressed while
S.T. (summer time) used for daylight saving time
display I will flash.
Timer is running, the time is reset to the
and "ON" or "OF" will begin flashing.
„Press the lower right button (A) to advance
original Timer set time and restarts the
„Press lower right button (A) to select S.T. "ON"
hours.
countdown automatically. When Timer
or "OF" (off).
„Press and release the lower left button (B).
counts down to zero, the time up signal
„Press and release lower left button (B).
Minutes in digital display I will flash. Press the
sounds for 5 seconds and the display
Seconds figures will flash. Use lower right
lower right button (A) to set minutes.
returns to the Timer set time and stops.
button (A) to reset seconds.
Setting alarm time sets alarm to on.
*Press and release the lower left button (B).
„Press the lower left button (B) to finalize
Minutes will flash. Press the lower right button
setting.
For additional features and instructions,
(A) to adjust minutes. Hold the lower right button
„To switch alarm off or on while in alarm
please refer to the full instruction manual
(A) continuously for rapid change.
mode, press the lower right button (A). While
or our web site at ww.citizenwatch.com.
in alarm mode, digital display II shows city
code.
Download PDF