Overhead door 03T User Manual

The Genuine. The Original.
~~:l
3Button Remote
\11
OPERATING INSTRUCTIONS
7 IMPORTANT INFORMATION
This remote is preset for use with the CodeDodger® 2
Access Security System. The remote can be configured
for use with the CodeDodger® 1 Access Security System.
See "Programming to CodeDodger® 1 Overhead Door
garage door openers" for instructions on switching from
CodeDodger® 2 to CodeDodger® 1.
~
~ro;~:~h~oor can cause serious injury
Wall Console must be mounted in sight
of door, at least 5 feet above floor and
clear of moving door parts.
• Keep people clear of opening while door is moving.
Do NOT allow children to play with the Remote or
door opener.
If safety reverse does not work properly:
• Close door then disconnect opener using the
manual release handle.
Do NOT use Remote or door opener.
Refer to Door and Door Opener Owner's Manuals
before attempting any repairs.
Electrical Shock can cause serious
injury or death.
Power cord must be unplugged before
attaching any wires.
• Be sure wire ends do not touch each
other or other terminals.
If you have questions or if you need a manual, contact
the distributor or manufacturer of the opener.
2 PROGRAM THE OPENER
(2) PRESSEi and HOLD S seconds
SEEBOTH Blue LEDs come ON
~\
0RE~::~:und ".,~.,,«'O~~.
~
-~~.'!l'~~'
-:;,.
Blue LED
come ON
,,~Y'
"'"~?;, <,
fi'\
F
PRESS
and RELEASE
\.:.J ~:~~?nni Purple LED
In
-
'= ~ ~ \
E21
:~~2''''rJ;~'''''
_ . .~ ,
,..
,- ,,-.
",,>n~'
14\
PRESSremote and RELEA~~ """
\.:..} (the button you want to program.)
o~
t 2:
<,
I
•
PRESSand
c
=.
II
~~o
10:~~~~~'~:
SEE
LED
come steady ON
RELEAS~ remote button again
"""ci~~::
o
' "
I
I'
SEEboth LEDs flash Blue and go OFF
PRESSand RELEASEremote button a third time
Programming is complete. This remote button can
now be used to operate door opener.
Repeat as necessary for other remotes or buttons on
the same remote.
3 REMOTE OPERATION
• Point Remote at the garage door and press the
button. Door will move.
• Pressthe Remote Button again and the door will
stop.
• Press the Remote Button again and the door will
move the opposite way. The door automatically
d 0 f t h e open or close cyc Ie.
h
stops at teen
Follow the instructions on this page. Otherwise, switch
remote from CODEDODGERc&l2 to CODEDODGERlllland follow
programming directions for yOu_,_d_oo_'_o'-pe_"_e_'.
--'
4 LOST ORSTOLEN REMOTE
ALL Remote Codes will be erased from Opener
(powerhead) memory.
These instructions are for openers with the type
keypad shown below.
1. PressCi and hold until
both lights come ON
blue. Releasebutton.
.
_.,. _.'
"".~.~"". R\_ ~\
~?~
-e- ~ \_
2. Lights go out and
\
Round BLUElight
comes ON.
/
m
U
3. PressJ again and see long
purple LEDflashing.
~ -~
~ \>l
4. Press both \} and [j
-e. .
simultaneouslyon+the
-O.!I,
~
powerhead and hold for . ~-~~~ _ ..-<>
5 seconds.
' ,",'.-
,...,~~ _~
_
,_ . U
-=: - \ SSECS
\
- ~\
Test remote
0':' "00:
Remote should not activate
door opener.
/1""""-
/
5. Reprogram the Opener with the remaining Remote(s)
(Repeat Section 2 for each remote).
Follow these instructions to erase remote codes for
ALL other Overhead Door openers.
1. Pressand HOLD the Learn Code button on the
powerhead for 10 seconds or until Radio Signal LED
indicator goes out.
2. Reprogram the Opener with the remaining Remotes
following the programming instructions for that
powerhead.
3. Reprogram the Opener with any Wireless Keypad
and other access device using the instructions
accompanying those devices.
5 BATTERY REPI.,ACEMENT
Replace remote battery with a CR 2032 coin cell battery.
1. Open the remote case using a washer or coin that fits
into the slot at the top of the remote.
2. Replace battery. Match battery polarity with symbols
inside battery housing.
3. Align components and snap case closed.
FCCand ICCERTIFIED
This device complies withFCC Part 15 andRSS 210 of Industry Canada.
This equipment has been tested and found to comply with the limits
foraClass B digitaidevice, pursuant to Part 15 of theFCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, jf not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. Ifthis equipment does cause
harmful interference to radio ortelevision reception, which may
bedetermined byturningtheequipment OFF andON, theuser is
encouraged to try to correct the interference by one or more of the
following measures: 1.Re-orient orrelocate thereceiver antenna,
2. Increase the separation between the opener and receiver, 3. Connect
theopener intoanoutletonacircuit different fromthatto whichthe
receiver isconne.cted,.4.Consult yourlocal dealer.
Changes or modifications notexpressly approved bythemanufacturer
could voidtheuser's authority to operate theequipment.
CODEDODGER® FEATURES
Other models of Overhead Door garage door openers,
remotes, and wireless keypads use Codefrodqer" 1 signals
to communicate. Remotes provided with this unit will
transmit either CodeDodger® 1 or Codefrodqer" 2 signals.
If you have ...
Use this
CodeDodger®
programming
One or more CodeDodger® 2 openers
with a maximum 3 different openers
Use
CodeDodger® 2
Mixture of openers manufactured
between 1997 and 2010
(CodeDodger® 1) and new
Codetiodqer" 2 openers
Use
CodeDodger® 2
and/or 1
One or more openers manufactured
between 1997 and 2010
(Codefrodqer'" 1)
Use
CodeDodger® 1
NOTE: A maximum of 3 different openers can be
programmed to a 3 button remote.
Three button
remote
,C-l
I --
5J
Red LED
Green LED
Programming to CodeDodger® 1 Overhead
Door garage door openers
The default CodeDodger® 2 setting must be changed to
CodeDodger® 1.
(Follow these same steps to change CodeDodger® 1 back
to CodeDodger® 2.)
The LED color displayed on the remote indicates the
CodeDodger® mode.
Red
=CodeDodger® 1 / Green =CodeDodger® 2
1. Select a button on the remote that has NOT been
programmed to the new powerhead.
2. Pressand hold that button for 10 seconds.
Both Red an.d Green LEDs
come ON and stay ON.
f1t
c.
2:'
10SECS'=-'
- 3. Pressthe same butt::
-
<,
I
~ttu
U
_
t~ice
to
toggle CodeDodger® selection
from CodeDodger® 2 to
CodeDodger® 1.
4. Pressthe same button again to
confirm toggle. The Codefrodqer"
selection for this button is set to
CodeDodger® 1.
5. Take the remote to the earlier
Overhead Door garage door
opener and follow that opener's
instructions to program a new
remote.
Repeat for other Overhead Door
garage remote(s) as necessary.
For additional information or help contact Customer
Service: Call1-800-929-DOOR
or write:
Overhead Door Corporation
22790 Lake Park Blvd.
Aliiance,Ohio
44601 U.s.A.