RIOTEC LS6320E Programming Quick Manual

Programming Quick Guide
OUTPUT MODE –
KEYBOARD / USB
OUTPUT
MODE
OUTPUT MODE
- RS232 (SERIAL)
I2OF5 DOUBLE
CHECK -ENABLE
SINGLE SCAN
READING
MODE
SINGLE SCAN
NO TRIGGER
ID2OF5 DOUBLE
CHECK -ENABLE
ID2OF5 DOUBLE
CHECK -DISABLE
LASER TIMEOUT
– 2 SECONDS
CODABAR DOUBLE
CHECK -ENABLE
CODABAR DOUBLE
CHECK -DISABLE
CODE 11 DOUBLE
CHECK -DISABLE
UPC/EAN DOUBLE
CHECK -ENABLE
UPC/EAN DOUBLE
CHECK -DISABLE
CODE 39 DOUBLE
CHECK -ENABLE
CODE 39 DOUBLE
CHECK -DISABLE
REVERSE IMAGE
–ENABLE
IMAGE
REVERSE IMANGE
-DISABLE
CODE 93 DOUBLE
CHECK -ENABLE
CODE 93 DOUBLE
CHECK -DISABLE
SEND BAR CODE ID
-DISABLE
CODE ID
SEND BAR CODE
ID – AS A PREFIX
CODE 128 DOUBLE
CHECK -ENABLE
CODE 128 DOUBLE
CHECK -DISABLE
SEND BAR CODE ID
-RESET
MSI DOUBLE
CHECK-ENABLE
MSI DOUBLE
CHECK -DISABLE
LS6320E./LS6320V./FS5020E
DOUBLE
CHECK
I2OF5 DOUBLE
CHECK -DISABLE
Installation
Make sure that the scanner has the correct cable to
plug into the PC as below described:
1.USB cable connection/ PS2 cable connection:
(Please use correct cable for the interface)
Reset Configuration to Default
If you are unsure of the scanner configuration or have
scanned the incorrect codes, please read the “Default”
barcode. This will reset the scanner to its factory
default.
Default
2.RS232 cable connection:
Please read above “Default” first,
and then set the output mode as
RS232 (SERIAL).
★If you want to switch to different interface, please
scan the correct configuration code (Output Mode,
right above), then, change the appropriate cable.
LASER TIMEOUT
– 5 SECONDS
CODE 11 DOUBLE
CHECK -ENABLE
DOUBLE
CHECK
3.Auto-sensing setup
The auto-sensing will be activated while scanner puts
on stand. When scanner is removed from stand, it
becomes trigger mode.
SEND BAR CODE
ID –AS A SUFFIX
Keyboard Language
Scan the appropriate country code below to program the
keyboard for your country or language. As a general rule,
the following characters are not supported by the scanner
for countries other than the United States:
@|$#{}[]=/‘\<>~
Symbologies On/OFF-2
Symbologies On/OFF-1
INTERLEAVED 2 OF 5
CODE 11
CODE 11
– DISABLE
I2OF5 - ENABLE
CODE 39
CODE 39
– DISABLE
ID2OF5 -ENABLE
FULL ASCII
– DISABLE
MSI - ENABLE
DENMARK
FINLAND
CODE 11
– ENABLE
FRANCE
GERMANY
CODE 39
– ENABLE
ITALY
LATIN AMERICA
FULL ASCII
– ENABLE
NETHERLANDS
NORWAY
CODE 93
– ENABLE
CODE 93
CODE 93
– DISABLE
UPC-A- ENABLE
POLAND
SPAIN
CODE 128
– ENABLE
CODE 128
CODE 128
– DISABLE
UPC-E -ENABLE
UPC-E -DISABLE
SWITZERLAND
(FRENCH)
SWITZERLAND
(GERMAN)
CODE 128 ISBT
– DISABLE
EAN-13 -ENABLE
EAN-13 -DISABLE
SWEDEN
UNITED KINGDOM
CODABAR
– DISABLE
EAN-8 -ENABLE
EAN-8 -DISABLE
UNIVERSAL
UNITED STATES
CODE 128 ISBT
– ENABLE
CODABAR
– ENABLE
CODABAR


I2OF5 - DISABLE
INDUSTRIAL 2 OF 5
ID2OF5 - DISABLE
MSI
UPC/EAN
MSI - DISABLE
UPC-A -DISABLE
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
2014.04.07