Bartec Pixavi Phone Quick Start Manual

Quick Start Guide
Product name: Pixavi Phone
Pixavi Thermal
Pixavi Cam
Type: 17-S13*-1***/*********
Introduction
Congratulations on your Pixavi intrinsically safe device.
All you need to get started with Pixavi Phone, Pixavi Cam and
Pixavi Thermal can be found in this quick guide. If you need
further assistance, try the AndroidTM help function, or visit:
www.bartecmobility.com/support-portal
Pixavi Phone (¹)
Intrinsically safe smartphone
Pixavi Thermal (²)
Intrinsically safe smartphone with FLIRTM thermal camera
Pixavi Cam (³)
Intrinsically safe camera
¹
( -3) Used to identify the product variants in this quick guide
Warnings
Warnings are used in this quick guide to warn of risks of
damage to property and personal injuries. Always read and
follow these warnings
DANGER:
designates a hazardous situation that can lead to death or serious,
permanent injuries if safety measures are disregarded.
ATTENTION:
designates a hazardous situation that can lead to material damage if
safety measures are disregarded.
Warranty
www.bartecmobility.com/warranty/pixavi
Your device
7
8
6
4
5
3
2
1
9
1: 5.5” OLED
10
11
2: Screen protector
3: Power button
4: Volume button (-/+)
5: Programmable button
6: Proximity/Ambient light sensor and status LED
7: Front Camera
8: Earpiece speaker
9: Lanyard mounting slot (remove battery pack for easy installation)
10: Magnetic USB connector
11: Microphone
Do not remove the screen protector! Replace with type:
17-S1Z0-0007 if damaged. Only replace the screen protector
outside the hazardous area.
5
4
3
2
1
6
7
8
9
1: Loudspeaker
2: Thermal camera (²)
3: Main camera
4: Flash
5: Microphone
6: Dual SIM/SD tray (¹, ²) or SD tray (³) (accessible behind battery pack)
7: Battery pack
8: Battery pack torx T10 fasteners
( )
9: NFC
( )
¹ Pixavi Phone
² Pixavi Thermal
³ Pixavi Cam
( )
SIM/SD tray
ejectorstarted
tool
Getting
Insert the SIM card and/or SD card and Battery pack
according to the instructions below.
The ejection tool can be found attached to the SIM/SD-card
instructions sheet (separate sheet)
Pixavi Phone (1)
Pixavi Thermal (2)
Pixavi Cam (3)
Ensure
the ejection
pin is perpendicular
to the hole.
Ensure
that that
the ejection
pin is perpendicular
to the hole. Otherwise,
the Otherwise,
device may be
damaged.
the
device may be damaged.
Use only nano-SIM cards and/or Micro SD card. Pixavi Phone and Pixavi Thermal
supports
2x nano-SIM
or 1x
nano-SIM
and Micro
1x microSD
SD.card.
PixaviPixavi
Cam supports
micro SD.
Use only
nano-SIM
cards
and/or
Phone 1x
and
Pixavi
Thermal
supports
2x nano-SIM
1x nano-SIM
and
SD.
If the card
is not fixed
firmly into
the tray, theor
SIM/SD
card may fall
out1x
ofmicro
the tray.
Pixavi Cam supports 1x micro SD.
Only insert or remove the battery outside the potentially explosive atmosphere
If the card is not fixed firmly into the tray, the SIM/SD card may fall
out
ofuse
thebatteries
tray. that have been certified by BARTEC, Type: 17-S1Z0-0001/****
Only
Only insert or remove the battery outside the potentially explosive
atmosphere
Only use batteries that have been certified by BARTEC,
Type: 17-S1Z0-0001/****
Charging
Insert the magnetic charger cable in the USB/Charging port
at the bottom of the device. Make sure the orientation of the
cable is as illustrated below.
Do not use any force when inserting the magnetic charging/USB cable.
The cable can only be inserted in the orientation illustrated above
The USB port shall only be used for charging the equipment when in the
non-hazardous area
For charging the device, use only Bartec approved chargers and cables
Power on your device
Press and hold the Power button to power on the device
Programmable button
The programmable button can be configured to launch an
applications or action on single tap, double tap and long
press.
It comes preconfigured but can be changed based on your
preferences. Go to Settings -> Programmable Button.
Other options:
Push-to-talk (PTT): Press and hold to talk.
Single tap, double tap and press and hold will be disabled
when PTT is activated.
SOS: Tap the button fast 5 times to send a SOS message to
one or multiple contacts.
Replacing battery pack
Make sure the device is turned off before replacing the
battery pack. Loosen the two fasteners with the supplied
Torx T10 screwdriver (the fasteners are captive screws and
not suppose to be fully removed). Remove the battery pack.
Replace the battery pack and tighten the fasteners.
Only insert or remove the battery outside the potentially explosive
atmosphere
Only use batteries that have been certified by BARTEC,
Type: 17-S1Z0-0001/****
Troubleshooting and Support
If the device becomes unresponsive or does not boot
successfully, try performing a soft reset. This is done by
pressing and holding the power button for 10 seconds.
FAQs and technical support can be found here:
www.bartecmobility.com/support-portal
Storage
Battery storage information:
The batteries of BARTEC (type 17-S1Z0-0001/****) are
developed and manufactured in accordance with the highest
industrial standards. The operating time or storage period of
a battery is restricted, however. The actual life of a battery is
influenced by different factors, e.g. hot, cold, rough operating
environment and physical damage.
Batteries kept for a duration of six months or longer should
be charged, discharged and charged again at least every
three months. If electrolyte has escaped, do not touch the
areas affected and dispose of the batteries properly. Replace
the battery if the operating time has shortened considerably.
The standard warranty period for all BARTEC batteries is
six months, whereby it is irrelevant whether the battery was
acquired separately or was contained in the scope of the
delivery of the device.
Make sure the battery pack is charged minimum every three months
Protect the device from constant moisture
Cleaning
Do not use any chemical cleaning agents to clean the deivce.
Use a damp cloth.
Cleaning: only clean with a damp cloth
Product marking
22CA80042090X
CL I; DIV 1; GP A, B, C and D; T4
Ex ia IIC T4 Ga
Class I, Zone 0, AEx ia IIC T4 Ga
CSANe 20ATEX4223X
II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db IP68
IECEx SIR 20.0036X
-20°C ≤ Ta ≤ +60°C
Top plate marking:
marking is always visible)
Variabel:
*= Product variant name (e.g.
Phone, Thermal, Cam)
hassis marking:
Marking is in the battery pack
ompartment. Not visible when
attery pack is inserted in the
evice)
ariabels:
ARIANT:
= Product variant name (e.g.
hone, Thermal, Cam)
Pixavi *
Rev info:
15.Oct.21: - Removed bar below WEE symbol for battery pack (Bar is not for batteries, o
- Added IEC number to battery pack
- Changed “WARNING” to “CAUTION” on battery pack
29.11.21: - Added KCs mark and number + RCM logo to device label. Rearanged logo p
02.11.21: - Added UL listed mark. Added min size of icons
28.01.22: - Changed UL mark and added UL numer
14.02.22: - Moved “secondary Li-ion battery” so that’s it’s above the UL mark
17.03.22: - Changed
NEC500
marking
Pixavi
*
Type: 17-S13*-1***/********
10.08.22: - updatedMfr:NEC500
BARTEC GmbH marking “changed zone1 to zone0”
Max-Eyth-Straße 16/ 97980 Bad Mergentheim, DE
15.08.22: - Added FCC
numbers and info
www.bartec.com
Input: 3.6V-6V 3A, 6V-9V 2A
Powered by 3.8V Li-ion battery
WARNING/ATTENTION:
- Only use battery type: 17-S1Z0-0001/****
- Utiliser uniquement la batterie type:
17-S1Z0-0001/****
/N:
Y= Year of manufacture,
T= Product variant code
XXXXX= unique serial number
FCC ID: TBU-X8K****
IC: 5736C-X8K****
nnnn
ype:
7-S13*-1***/********
ifferent type codes for each
roduct variant
TPP : Pixavi Thermal, Pixavi Phone
C : Pixavi Cam
op plate marking:
marking is always visible)
attery pack marking:
marking is on the back side of
he battery pack. Not visible
when battery pack is inserted in
he device)
QRcode
E code:
nnn= Certifying body number
sed for factory audits
S/N:
X8KYYTTXXXXXX
Battery Pack labels
WARNING
ATTENTION
Do not replace battery or use USB port in hazardous area!
Read user manual before use!
Ne pas remplacer la batterie ou utiliser le port USB a l’intérieur d’une zone explosive
Lire attentivement le mode d’emploi avant toute utilisation!
Pixavi Battery
Type: 17-S1Z0-0001/0001
Mfr: BARTEC GmbH
Max-Eyth-Straße 16/ 97980 Bad Mergentheim, DE
Battery info 3.8 V , 3200 mAh , 12.16 Wh
Limited Charge Voltage (4.35 V)
CAUTION
Only use with type: 17-S13*-1***/*********
Do not disassemble, short circuit
or dispose of in fire!
Dispose of used batteries properly!
IEC: 1ICP6/54/78
ariabel:
/N:
Y= Year of manufacture,
XXXXX= unique serial number
Varia
S/N:
YY=
XXXX
21-AV4BO-0271X
E code:
nnn= Certifying body number
sed for factory audits
CC ID: TBU-X8K****
C: 5736C-X8K****
Batt
(mar
the b
when
the d
nnnn
Secondary Li-ion battery
9YA1
QRcode
S/N:
X8KYYPBXXXXXX
CE c
nnnn
used
Explosion protection
ATEX Zone 1 / 21
Type
17-S13*-1***/*********
Marking
II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db
-20°C ≤ Ta ≤ +60°C
Test certificate
CSANe 20ATEX4223X
IECEx Zone 1 / 21
Type
17-S13*-1***/*********
Marking
Ex ib IIC T4 Gb
Ex ib IIIC T135°C Db
-20°C ≤ Ta ≤ +60°C
Test certificate
IECEx SIR 20.0036X
NEC 500/505
Type
17-S13*-1***/*********
Marking
Class I; Division 1; Groups A, B, C and D; T4
Ex ia IIC T4 Ga
Class I, Zone 0, AEx ia IIC T4 Ga
Test certificate
CSA 22CA80042090X
Temperature range
ATEX/IECEx (EN IEC 60079-0)
-20 °C ≤ Ta ≤ +60 °C (-4 °F ≤ Ta ≤ 140 °F)
Discarge (EN IEC 62368-1)
-20 °C ≤ Ta ≤ +50 °C (-4 °F ≤ Ta ≤ 122 °F)
Charging (EN IEC 62368-1)
0 °C ≤ Ta ≤ +45 °C (32 °F ≤ Ta ≤ 113 °F)
Long term storage
0 °C ≤ Ta ≤ +35 °C (32 °F ≤ Ta ≤ 95 °F)
EX port parameters
IEC
Parameters
USA
Parameters
USB (magnetic
connector)
SIM (1&2)
card
SD card
Unit
Uo
Voc
5.45
5.45
5.45
V
Io
Isc
2.81
1.20
7.04
A
Po
Pout
0.84
0.41
2.59
W
Co
Ca
N/A
27.40
39.30
μF
Lo
La
N/A
24.97
0.72
μH
USB Ui and device Um (non-hazardous area connection only) = 12V.
Specific conditions for use
The USB port shall only be used for charging the equipment
when in the non-hazardous area.
Um (Charging / USB contacts) = 12V, this is ensured by
using a charger type G7-S0Z0-0001 - G7-S0Z0-0004 or
other accessories specified by Bartec GmbH. The ambient
temperature during charging shall be in the range 0ºC to 45ºC.
The USB port is also used for data download. The port has
been assessed with a Um of 12 V and shall be installed in
accordance with IEC 60079-14/EN 60079-14.
Care should be taken to avoid the risk of drop and impact
during storage, transportation and use as aluminium is
present in the structure of the enclosure.
The apparatus shall not be subjected to a prolific charge
generating mechanism (such as might occur in pneumatic
transfer of powders or charge spraying in a powder coating
process).
Do not remove the battery pack in the hazardous location.
The battery pack surfaces shall at regular intervals be checked
for wear and tear by the user. Replace with type:
17-S1Z0-0001/**** if damaged.
General safety requirements
Only use accessories that are approved by BARTEC
In the case of malfunction or damaged enclosure, remove the
device immediately from the potentially explosive atmosphere.
Specific Absorption Rate Data
The Pixavi Phone, Pixavi Thermal and Pixavi Cam is a radio
transmitter and receiver. It is designed and manufactured
not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government, Industry Canada
of the Canadian Government (IC), and recommended by the
Council of the European Union. The exposure standard for
wireless devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC/IC is 1.6W/kg averaged over 1
gram of actual tissue.
The SAR limit recommended by The Council of the European
Union is 2.0W/kg averaged over 10 g of actual tissue.
The SAR value measured for the Pixavi Phone, Pixavi Thermal
and Pixavi Cam:
FCC/ID
Pixavi Phone/Thermal
Head
0.626 W/kg
FCC/ID
Pixavi Phone/Thermal
Body
1.202 W/kg
FCC/ID
Pixavi Cam
Head
0.571 W/kg
FCC/ID
Pixavi Cam
Body
0.148 W/kg
CE
Pixavi Phone/Thermal
Head
0.164 W/kg
CE
Pixavi Phone/Thermal
Body
0.633 W/kg
FCC/ISED
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement
économique Canada.
Legal
Android is a trademark of Google LLC.
Phone: +49 7931 597-0
[email protected]
11-S130-7E0001-Rev01-450631
BARTEC GmbH
Max-Eyth-Str. 16
97980 Bad Mergentheim, Germany