Dorel 9257196COMUK Manual

9257196COMUK
LIFT TOP DESK
B349257196COMUK01
Date of Purchase: ____/____/_____
Lot Number:
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Do Not Return This Product!
Contact our customer service team for help first
Call: 01942 524100
email: [email protected]
Easy
WARNING
–Unit can !p over causing severe injury or death.
–Anchor unit to stud in wall (if instructed to)
–Do not allow children climb on unit
–Put heavy items on lower shelves or drawers
Tough
Assembly Difficulty Meter
Contact Us!
Do NOT return this product!
Contact our friendly customer service team first for help
Call us!
01942 524100
[email protected]
Helpful Hints
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR
- Open your item in the area you plan to keep it for less heavy li!ing
- Iden"fy, sort and count the parts before a#emp"ng assembly
- Compression dowels are tapped in with a hammer
- Slides are labeled with a R (right) and L (le!) for proper placement
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge
- Use all the nails provided for the back panel and spread them out equally
- Back Panel must be used to make sure your unit is sturdy
- Do NOT use harsh chemicals or abrasive cleaners on this item
- Never push, pull, or drag your furniture
2
k
Quic ly
mb
e
s
s
A
Ti p
Before You Start
P
P
P
P
P
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Cau!on: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is !ght.
Failure to do so may result in stripping the screw.
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
1
2
3
4
3
Board Iden•fica•on
Not actual size
1
2
x1
T9257096010UD
LIFT TOP PANEL
4
3
x1
T9257096020UD
RIGHT TOP PANEL
6
5
x1
T9257096040UD
MIDDLE PARTITION
7
x1
T9257096050UD
SIDE SUPPORT PANEL
8
x1
T9257096070UD
FRONT PANEL
10
x1
T9257096060UD
RIGHT SIDE PANEL
9
x1
T9257096080UD
RIGHT FRONT APRON
11
x1
T9257096100UD
UPPER SHELF
x1
T9257096030UD
LEFT SIDE PANEL
x1
T9257096090UD
UPPER BACK PANEL
12
x1
T9257096110UD
LEFT FRAME
4
x1
T9257096120UD
LEFT FRONT APRON
Board Iden•fica•on
Not actual size
13
14
x1
T9257096130UD
LEFT BACK PANEL
16
15
x1
T9257096140UD
BACK PANEL SUPPORT
18
17
x1
T9257096160UD
RIGHT FRAME
19
x1
T9257096170UD
MIDDLE RAIL
20
x1
T9257096190UD
LOWER SHELF
x1
T9257096220UD
FOOT
x1
T9257096180UD
RIGHT BACK PANEL
21
x2
T9257096200UD
LOWER SUPPORT PANEL
23
22
x1
T9257096150UD
MIDDLE FRAME
x2
T9257096210UD
LOWER SUPPORT PANEL
24
x2
T9257096230UD
FOOT
5
x1
T9257096240UD
FOOT
Board Iden•fica•on
Not actual size
25
26
x1
T9257096250UD
LEFT SUPPORT PANEL
28
27
x1
T9257096260UD
RIGHT SUPPORT PANEL
30
29
x1
T9257096280UD
UPPER DRAWER FRONT
31
x1
T9257096290UD
UPPER DRAWER LEFT
32
x1
T9257096310UD
UPPER DRAWER BACK
x1
T9257096340UD
MIDDLE DRAWER LEFT
x1
T9257096300UD
UPPER DRAWER RIGHT
33
x2
T9257096320UD
DRAWER BOTTOM
35
34
x4
T9257096270UD
SUPPORT WOOD BLOCK
x1
T9257096330UD
MIDDLE DRAWER FRONT
36
x1
T9257096350UD
MIDDLE DRAWER RIGHT
6
x1
T9257096360UD
MIDDLE DRAWER BACK
Board Iden•fica•on
Not actual size
37
38
x1
T9257096370UD
LOWER DRAWER FRONT
40
39
x1
T9257096380UD
LOWER DRAWER LEFT
42
41
x1
T9257096400UD
LOWER DRAWER BACK
43
x1
T9257096410UD
LOWER DRAWER BOTTOM
44
x1
T9257096430UD
LIFT MECHANISM
x1
T9257096390UD
LOWER DRAWER RIGHT
x1
T9257096420UD
LIFT MECHANISM
45
x1
T9257096440UD
SUPPORT TUBE
7
x1
T9257096450UD
SUPPORT TUBE
Hardware Bag Reference Number:
29257096COM0UD
Part List
Actual Size
x54
TUD0001
Cam Bolt
x54
TUD0002
Cam Lock
15-12
x36
TUD0030
DOWEL 6 X 30
x39
TUD0009
CBS 4 x 38
x8
TUD0022
CBS 4 X 30
x50
TUD0008
CBS 3.5 x 16
x6
TUD0007
CBS 3.5 x 12
x8
TUD0011
PH M4 X 12
8
Hardware Bag Reference Number:
29257096COM0UD
Part List
Not Actual Size
x12
TUD0047
JCBC SCREW
6 X 40
x1 SET
TUD0049
FULL EXT. SLIDE
350 MM
x2 SETS
TUD0017
DRAWER SLIDE
350 MM
x8
TUD0052
JCBC SCREW
6 X 30
x4
TUD0048
BARREL NUT
1/4” X 12
x2
TUD0050
METAL FILE HOLDER
Ø5 X 356
x1
TUD0054
WRENCH
10 MM
x8
TUD0053
NUT 6 X 10
9
x1
TUD0026
ALLEN KEY
M4
x4
TUD0012
HANDLE
x8
TUD0041
SPRING WASHER
Step 1
* raw edges are shaded
10
Step 2
x9
TUD0001
x8
TUD0002
23
22
x8
TUD0030
x8
TUD0009
24
23
20
23
20
22
21
24
21
19
* raw edges are shaded
11
Step 3
x1 SET
TUD0016
x6
TUD0001
x12
TUD0008
x1 SET
TUD0049
15
16
TUD0049
(Cabinet member)
* raw edges are shaded
12
Step 4
Quick
Assembly
Tip
Proper orientation of CAM LOCK
x6
TUD0002
x2
TUD0030
17
16
18
15
* raw edges are shaded
13
Step 5
x4
TUD0030
x4
TUD0009
* raw edges are shaded
14
Step 6
x7
TUD0001
15
19
11
* raw edges are shaded
15
Step 7
Quick
Assembly
Tip
x8
TUD0002
Proper orientation of CAM LOCK
x4
TUD0030
15
13
12
11
14
* raw edges are shaded
16
Step 8
x12
TUD0001
x1
TUD0012
x2
TUD0011
9
7
8
* raw edges are shaded
17
Step 9
Quick
Assembly
Tip
Proper orientation of CAM LOCK
x12
TUD0002
6
8
9
4
7
3
Note : Hole Boring Bo!om
* raw edges are shaded
18
Step 10
x4
TUD0001
x8
TUD0030
x13
TUD0009
8
5
6
7
10
* raw edges are shaded
19
Step 11
Quick
Assembly
Tip
x4
TUD0002
Proper orientation of CAM LOCK
x6
TUD0030
* raw edges are shaded
20
Step 12
x1
TUD0026
x2
TUD0009
x1 SET
TUD0016
x8
TUD0047
x6
TUD0008
* raw edges are shaded
21
Step 13
Quick
Assembly
Tip
x4
x8
TUD0001 TUD0022
Proper orientation of CAM LOCK
x4
TUD0030
x4
TUD0002
2
2
27
27
* raw edges are shaded
22
Step 14
x8
TUD0052
x1
TUD0054
x8
TUD0053
x1
TUD0026
x8
TUD0041
45
TUD0053
44
TUD0054
42
TUD0041
43
TUD0026
* raw edges are shaded
23
Step 15
x20
TUD0008
1
Right
26
1
25
43
42
Note: Facing front
Le!
* raw edges are shaded
24
Step 16
x4
TUD0047
x4
TUD0048
x1
TUD0026
26
25
1
27
* raw edges are shaded
25
Step 17
x12
TUD0001
28
33
37
* raw edges are shaded
26
Step 18
Quick
Assembly
Tip
Proper orientation of CAM LOCK
x8
TUD0002
30 / 35
x2
29 / 34
x2
* raw edges are shaded
27
Step 19
Quick
Assembly
Tip
Proper orientation of CAM LOCK
30
29
28
* raw edges are shaded
28
Step 20
32
28
* raw edges are shaded
29
Step 21
x4
TUD0009
31
* raw edges are shaded
30
Step 22
x1 SET
TUD0016
x6
TUD0008
* raw edges are shaded
31
Step 23
Quick
Assembly
Tip
Proper orientation of CAM LOCK
35
34
33
* raw edges are shaded
32
Step 24
32
33
* raw edges are shaded
33
Step 25
x4
TUD0009
36
* raw edges are shaded
34
Step 26
x1 SET
TUD0016
x6
TUD0008
* raw edges are shaded
35
Step 27
x4
TUD0002
x1 SET
TUD0049
x6
TUD0007
TUD0049
(Drawer member)
38
39
* raw edges are shaded
36
Step 28
Quick
Assembly
Tip
Proper orientation of CAM LOCK
38
39
37
* raw edges are shaded
37
Step 29
x4
TUD0009
x2
TUD0050
40
TUD0050
41
37
* raw edges are shaded
38
Step 30
x3
TUD0012
x6
TUD0011
28
33
37
* raw edges are shaded
39
Step 31
28
33
* raw edges are shaded
40
Step 32
* raw edges are shaded
41
Step 33
TUD0050
* raw edges are shaded
42
Maximum Loads
This unit has been designed to support the maximum loads shown. Exceeding these load limits
could cause sagging, instability, product collapse, and/or serious injury.
Warning: Please make sure that all the objects are removed before moving the assembled unit.
The unit must be li!ed by more than one person, not dragged or pushed. Failure to do so will
cause product damage, instability, product collapse, and/or serious injury.
43