E2S DL112HDC024 Instructions/Service Manual

INSTRUCTION & SERVICE MANUAL
DL112H AlertAlight Combined Metal Sounder LED Beacons
•
•
•
•
-2 °C to + C (-13°F to 131°F)
Type 4 / 4X / 3R / 13, IP66
1.8Kg (3.96lb)
CE, All units UL Listed.
Voltage Range
Nominal
Sounder
Current*
Nominal
Beacon
Current*
12 V dc
10-14Vdc
200mA
79. mA
24V dc
16-30Vdc
200mA
86. mA
DL112HDC048
48V dc
42- 4Vdc
120mA
60mA
DL112HAC230
11 V ac
11 V ac ± 10%
100mA
34mA
DL112HAC230
230V ac
230V ac ± 10%
60mA
18. mA
Unit Type Code
Nominal Voltage
#
Nominal SPL
Max SPL
103dB(A) Tone
44 @ 1m
119dB(A) Tone
4 @ 1m
DL112HDC024
*Nominal current at nominal voltage, Tone 12 / 1Hz Flash Pattern; #Factory Default setting 24Vdc, beacon customer settable to 12Vdc
mm
0.4Nm
AC: 1.0 – 2. mm2 / AWG18
AWG12
0. 2. –mm
DC: 0.2 – 2. mm2 / AWG24 – AWG12
Attention: Installation must be carried out by an electrician in compliance with the latest codes and regulations.
Attention: L'installation doit être effectuée par un électricien conformément aux derniers codes et réglementations.
Achtung: Die Installation muss von einem Elektriker gemäß den neuesten Vorschriften und Bestimmungen durchgeführt werden.
Attenzione: L'installazione deve essere eseguita da un elettricista in conformità con i codici e le normative più recenti.
Atención : La instalación debe ser realizada por un electricista de acuerdo con los últimos códigos y regulaciones.
Atenção: A instalação deve ser realizada por um eletricista de acordo com os códigos e regulamentos mais recentes.
Внимание : установка должна выполняться электриком в соответствии с последними нормами и правилами.
Attention: Disconnect from power source before installation or service to prevent electric shock
Attention: Débranchez-le de la source d'alimentation avant l'installation ou l'entretien pour éviter tout choc électrique.
Achtung: Vor Installation oder Wartung von der Stromquelle trennen, um einen Stromschlag zu vermeiden.
Attenzione: scollegare dall'alimentazione prima dell'installazione o dell'assistenza per evitare scosse elettriche.
Atención : desconéctelo de la fuente de alimentación antes de la instalación o el servicio para evitar descargas eléctricas.
Atenção: Desconecte da fonte de alimentação antes da instalação ou serviço para evitar choque elétrico
Внимание : отключите от источника питания перед установкой или обслуживанием, чтобы предотвратить поражение электрическим током.
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH
[email protected]
e2s.com
D173-00-201-IS Issue 4 19/11/2021
AC
(See D173-06-20 )
E L N
C S2 S3
S1
E NL
LNE
S1
DC
+ - S2 S3
(See D173-06-201)
L3
S1
E - +
+ - E
S1
(AC & DC, See Tone Table)
Reverse Polarity Switching - On DC versions
the second stage alarm tone can be selected
by reversing the polarity of the
Default = S1 - Tone 1
supply voltage if switch 6 is in the ON position if
Link LK3 is present.
(ON = 1, OFF = 0)
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH
[email protected]
e2s.com
D173-00-201-IS Issue 4 19/11/2021
INSTRUCTION & SERVICE MANUAL
DL112H AlertAlight Combined Metal Sounder LED Beacons
267. mm 10. 4 in.
130.0mm .12 in.
4x
1.5Nm
90.0mm 3.
6.7mm 0.27 in.
in.
9.7mm 0.38 in.
2 OFF M20 X 1.
THREADED
CABLE ENTRIES
147.0mm .79 in.
For DL112HDC units, using a ring terminal, fit
an Earth to the shown location underneath the
M4 screw and M4 spring washer. This point
shall not be used for any other purpose (e.g.
ground bonding).
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH
[email protected]
e2s.com
D173-00-201-IS Issue 4 19/11/2021
S1 - LED Flash Mode Settings (AC & DC)
The Flash Mode Dip Switch can be changed to set the desired
flash pattern
ON
1 2 3
Flash Mode DIP Switch – Shown with 1-OFF, 2-ON, 3-OFF (0 1 0),
This denotes Flash mode 1Hz. For further flash modes refer to
table:
Switch
Setting
Flash Mode
000
Steady on
100
Blinking
010
Flashing 1Hz*
110
Flashing 1. Hz*
001
Flashing - Double Strike
101
Flashing - Triple Strike
011
Flashing 2Hz*
111
Flashing - Temporal
• All models are approved for use as Audible Signal and Visual Appliance
for use as General Signaling: UL464A & CSA C22.2 No 20 -17, UL1638A
• Type 4 / 4X / 3R / 13, IP66
• -2 °C to + °C / -13°F to +131°F
• To maintain Ingress Protection, cable entries must be fitted with suitably rated cable glands or stopping plugs
• Units can be mounted using the 2-off 10 x 7mm obround holes in the mounting lugs.
• EOL Monitoring (DC Only): End of Line Devices may be fitted between the +ve & -ve terminals of the PCBA. Please ensure that the device
legs meet the wire size range stated for the connection terminals and are fitted correctly in order to avoid a short. Refer to the compatible
control panel specification for EOL device values and ratings
Nominal Operating Current#
Model
Nominal* Voltage
Voltage Range
Beacon
Sounder
12V dc
10-14Vdc
79. mA
200mA
24V dc
16-30Vdc
86. mA
200mA
DL112HDC048
48V dc
48-60Vdc
60mA
120mA
DL112HAC11
11 V ac
11 V ac ± 10% 0/60Hz
34mA
100mA
DL112HAC230
230V ac
230V ac ± 10% 0/60Hz
19mA
60mA
DL112HDC024
*Nominal Voltage, 1Hz Flash Pattern & Tone 12; #Worst-case input voltage and worst case flash pattern
Warnings
Attention: Installation must be carried out by an electrician in compliance with the National Electrical Code, NFPA 70 or CSA 22.1
Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32. / L'installation doit exclusivement être
réalisée par du personnel qualifié, conformément au code national d'électricité américain, NFPA 70 ou CSA 22.1 Code canadien de
l'électricité, première partie, norme de sécurité relative aux installations électriques, Section 32
Attention: Disconnect from power source before installation or service to prevent electric shock / Débranchez-le de la source
d'alimentation avant l'installation ou l'entretien pour éviter tout choc électrique.
Attention: Do not paint / Ne pas Peinturer
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH
[email protected]
e2s.com
D173-00-201-IS Issue 4 19/11/2021
INSTRUCTION & SERVICE MANUAL
DL112H AlertAlight Combined Metal Sounder LED Beacons
Stage 1
Set DIP
SW 1
Tone No.
1
1
2
3
4
6
7
8
9
10
11
12
13
14
1
16
17
18
19
20
21
22
23
24
2
26
27
28
29
30
31
32
33
34
3
36
37
38
39
40
41
42
43
44
4
Tone Description
Tone Visual
340Hz Continuous
800/1000Hz @ 0.2 s Alternating
00/1200Hz @ 0.3Hz 0. s Slow Whoop
800/1000Hz @ 1Hz Sweeping
2400Hz Continuous
2400/2900Hz @ 7Hz Sweeping
2400/2900Hz @ 1Hz Sweeping
00/1200/ 00Hz @0.3Hz Sweeping
1200/ 00Hz @ 1Hz DIN / PFEER P.T.A.P
2400/2900Hz @ 2Hz Alternating
1000Hz @ 1Hz Intermittent
800/1000Hz @ 0.87 Hz Alternating
2400Hz @ 1Hz Intermittent
800Hz @ 0.2 s on, 1s off Intermittent
800Hz Continuous
660Hz 1 0ms on, 1 0ms off Intermittent
44Hz (100ms)/440Hz (400ms) NNF S 32 001
660Hz 1.8s on, 1.8s off Intermittent
1.4KHz 1.6KHz 1s, 1.6KHz 1.4KHz 0. s NFC48 26
660Hz Continuous
4/440Hz @ 1Hz Alternating
44Hz @ 0.87 s Intermittent
800Hz @ 2Hz Intermittent
800/1000Hz @ 0Hz Sweeping
2400/2900Hz @ 0Hz Sweeping
Bell
4Hz Continuous
440Hz Continuous
800/1000Hz @ 7Hz Sweeping
300Hz Continuous
660/1200Hz @ 1Hz Sweeping
Two Tone Chime
74 Hz @ 1Hz Intermittent
1000 & 2000Hz @ 0. s Alternating Singapore
420Hz @ 0.62 s Australian Alert
00 1200Hz 3.7 s/0.2 s Australian Evacuation
1000Hz Continuous PFEER Toxic Gas
2000Hz Continuous
800Hz 0.2 s on, 1s off Intermittent
44Hz (100ms) / 440Hz (400ms) NF S 32 001
Motor Siren Slow rise to 1200Hz
Motor Siren Slow rise to 800Hz
1200Hz Continuous
Motor Siren Slow rise to 2400Hz
1KHz 1s on, 1s off Intermittent PFEER Gen. Alarm
SW1 Setting
1234 6
000000
100000
010000
110000
001000
101000
011000
111000
000100
100100
010100
110100
001100
101100
011100
111100
000010
100010
010010
110010
001010
101010
011010
111010
000110
100110
110110
001110
101110
011110
111110
000001
100001
010001
110001
001001
101001
011001
111001
000101
100101
010101
110101
Stage 2
Tone (S2)
2
17
2
6
3
7
10
2
1
7
2
4
1
4
2
18
2
2
2
2
2
2
6
29
29
2
26
2
7
2
26
26
2
38
36
3
9
34
23
31
2
2
2
2
38
Stage 3
Tone (S3
20
2
27
1
1
4
4
4
17
27
34
Note: Please check factory settings and ensure the correct alarm tone is selected for your country or application
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH
[email protected]
e2s.com
D173-00-201-IS Issue 4 19/11/2021
3
E
N/L/+
DATE
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
7
8
A
ISSUE
MOD No.
9
10
REASON - INITIAL - DATE
INTRODUCTION
RSR - 20/12/2021
E
N/L/+
Stage 3 -ve
Stage 2 -ve
Stage 1 +ve OUT
Stage 1 -ve OUT
S3
L/+
N/E
A3
C
B
A
G
F
ALERTALARM RANGE
STANDARDS
R.N.POTTS
APPROVED
B.ISARD
CHECKED
DRAWING TO BS8888:2000
DRAWN
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
R.S.RAIT
ANGULAR DIMENSIONAL TOLS
Stage 1 +ve IN
20/12/2021
DATE
20/12/2021
DATE
20/12/2021
ALTERNATIVE MATERIAL
MATERIAL
SURFACE FINISH WEIGHT (Kg)
+
+
C
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
WWW.E2S.COM
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
2S
warning signals
Common +ve
SHEET
NTS 1 OF 2
SCALE
D173-06-251
DRAWING NUMBER
SOUNDER & LED WIRING DIAGRAMS
TITLE DL112H DC COMBINED
IF IN DOUBT, ASK DO NOT SCALE
ALL DIMENSIONS IN MM
+
+
-
Stage 1 -ve
-
S2
-
S2
G
F
E
S3
6
Linked Sounder & Beacon Activation (Default)
Config.: 1a Two/Three Stage Sounder Configuration
Config.: 1b
Stage 1: Apply Power to Common +ve & Stage 1 -ve
Stage 2: Apply Power to Common +ve & Stage 1 -ve & connect Stage 2 -ve to Stage 1 -ve
Stage 3: Apply Power to Common +ve & Stage 1 -ve & connect Stage 3 -ve to Stage 1 -ve
5
E
L/+
N/E
4
D
Stage 1 -ve IN
Stage 1 +ve OUT
Stage 1 -ve OUT
Single Stage Configuration
Stage 1: Apply Power to Stage 1 +ve & Stage 1 -ve
WIRING LINKING BEACON & SOUNDER
FACTORY FITTED
2
D
C
B
A
1
3
E
N/L/+
DATE
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
7
8
A
ISSUE
MOD No.
9
10
REASON - INITIAL - DATE
INTRODUCTION
RSR - 20/12/2021
+ve OUT
-ve OUT
E
N/L/+
Stage 3 -ve
Stage 2-ve
+ve IN
-ve IN
S3
L/+
N/E
G
F
ALERTALARM RANGE
STANDARDS
R.N.POTTS
APPROVED
B.ISARD
CHECKED
DRAWING TO BS8888:2000
DRAWN
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
R.S.RAIT
ANGULAR DIMENSIONAL TOLS
Stage 1 + IN
Stage 1 + OUT
20/12/2021
DATE
20/12/2021
DATE
20/12/2021
ALTERNATIVE MATERIAL
MATERIAL
SURFACE FINISH WEIGHT (Kg)
+
+
-
-
S2
C
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
WWW.E2S.COM
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
2S
warning signals
Common +ve IN
Common +ve OUT
Stage 1 -ve OUT
Stage 1 -ve IN
SHEET
NTS 2 OF 2
SCALE
D173-06-251
DRAWING NUMBER
SOUNDER & LED WIRING DIAGRAMS
TITLE DL112H DC COMBINED
IF IN DOUBT, ASK DO NOT SCALE
ALL DIMENSIONS IN MM
+
+
-
-
S2
A3
+ve OUT
-ve OUT
C
B
A
G
F
E
S3
6
Independent Sounder & Beacon Activation (Remove Link Wires)
Config.: 2a Two/Three Stage Sounder Configuration
Config.: 2b
Stage 1: Apply Power to Common +ve & Stage 1 -ve
Stage 2: Apply Power to Common +ve & Stage 1 -ve & connect Stage 2 -ve to Stage 1 -ve
Stage 3: Apply Power to Common +ve & Stage 1 -ve & connect Stage 3 -ve to Stage 1 -ve
5
E
L/+
N/E
4
D
Stage 1 - OUT
Stage 1 - IN
+ve IN
-ve IN
Single Stage Configuration
Stage 1: Apply Power to Stage 1 +ve & Stage 1 -ve
2
D
C
B
A
1
G
F
E
D
C
B
A
3
WIRING LINKING BEACON & SOUNDER
FACTORY FITTED
2
ALERTALARM RANGE
STANDARDS
R.N.POTTS
APPROVED
B.ISARD
CHECKED
DRAWING TO BS8888:2000
DRAWN
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
R.S.RAIT
ANGULAR DIMENSIONAL TOLS
Earth
20/12/2021
DATE
20/12/2021
DATE
20/12/2021
L/+
N/E
4
ALTERNATIVE MATERIAL
MATERIAL
5
6
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
7
8
A
ISSUE
MOD No.
9
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
WWW.E2S.COM
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
2S
warning signals
Earth
Stage 1 Live IN
Stage 1 Neutral IN
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
C
E
N/L/+
Stage 3
Stage 2
Common
Stage 1 Live OUT
Stage 1 Neutral OUT
S3
L/+
N/E
A3
Config.: 1b
SHEET
NTS 1 OF 2
SCALE
D173-06-255
DRAWING NUMBER
SOUNDER & LED WIRING DIAGRAMS
TITLE DL112H AC COMBINED
IF IN DOUBT, ASK DO NOT SCALE
ALL DIMENSIONS IN MM
E
E
L
L
N
N
C
S2
10
REASON - INITIAL - DATE
INTRODUCTION
RSR - 20/12/2021
Linked Sounder & Beacon Activation (Default)
Config.: 1a Two/Three Stage Sounder Configuration
Stage 1: Apply Power to Live & Neutral
Stage 2: Apply Power to Live & Neutral & connect Stage 2 to Common
Stage 3: Apply Power to Live & Neutral & connect Stage 3 to Common
SURFACE FINISH WEIGHT (Kg)
E
E
L
L
N
C
N
DATE
S3
S2
Stage 1 Live IN
E
N/L/+
Stage 1 Neutral IN
Stage 1 Live OUT
Stage 1 Neutral OUT
Single Stage Configuration
Stage 1: Apply Power to Stage 1 Live & Stage 1 Neutral
1
G
F
E
D
C
B
A
G
F
E
D
C
B
A
2
3
ALERTALARM RANGE
STANDARDS
R.N.POTTS
APPROVED
B.ISARD
CHECKED
DRAWING TO BS8888:2000
DRAWN
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
R.S.RAIT
ANGULAR DIMENSIONAL TOLS
Stage 1 Live IN
Stage 1 Live OUT
Earth
Stage 1 Neutral OUT
Stage 1 Neutral IN
Earth
Neutral IN
Live IN
20/12/2021
DATE
20/12/2021
DATE
20/12/2021
DATE
Single Stage Configuration
Stage 1: Apply Power to Stage 1 Live & Stage 1 Neutral
1
S3
6
7
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
C
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
8
WWW.E2S.COM
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
2S
warning signals
Stage 1 Live IN
Stage 1 Live OUT
Earth
Stage 1 Neutral OUT
Stage 1 Neutral IN
Stage 3
Stage 2
Common
Earth
Neutral IN
Live IN
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
Live OUT
Neutral OUT
Earth
ALTERNATIVE MATERIAL
MATERIAL
5
A
ISSUE
MOD No.
9
S3
Config.: 2b
SHEET
NTS 2 OF 2
SCALE
D173-06-255
DRAWING NUMBER
SOUNDER & LED WIRING DIAGRAMS
A3
Live OUT
Neutral OUT
Earth
TITLE DL112H AC COMBINED
IF IN DOUBT, ASK DO NOT SCALE
ALL DIMENSIONS IN MM
E
E
L
L
N
N
C
S2
10
REASON - INITIAL - DATE
INTRODUCTION
RSR - 20/12/2021
Independent Sounder & Beacon Activation (Remove Link Wires)
Config.: 2a Two/Three Stage Sounder Configuration
Stage 1: Apply Power to Live & Neutral
Stage 2: Apply Power to Live & Neutral & connect Stage 2 to Common
Stage 3: Apply Power to Live & Neutral & connect Stage 3 to Common
SURFACE FINISH WEIGHT (Kg)
E
E
L
L
N
N
C
S2
4
G
F
E
D
C
B
A
Page left Intentionally blank
Page left Intentionally blank
Page left Intentionally blank