Billion BiPAC 7402(G)X(L) Series User manual

BiPAC 7402(G)X(L) Series
3G/ ADSL2+ (802.11g) (VPN)
Firewall Router
Quick Start Guide
Quick Start Guide
Billion BiPAC 7402(G)X(L) Series ADSL2+ Router
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
Package Contents
BiPAC 7402(G)X(L) Series ADSL2+ Router
CD containing the on-line manual
RJ-11 ADSL/telephone cable
Ethernet (CAT-5 LAN) cable
One 2dbi detachable antenna (Wireless model only)
Power adapter
RJ-45 to RS-232 Console Kit
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
Attention
1
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this product and all accessories outdoors.
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Quick Start Guide
Hardware Overview
BiPAC 7402X(L) does not support 802.11g and WPS functions.
The Front LEDs
Lit orange red when
power is ON. Lit red
means system is fail.
Lit green when the
system is ready.
Lit when connected to an
Ethernet device. Green for
100Mbps; Orange for 10Mbps.
Blinking when data is
Transmitted / Received.
Lit green when the wireless
connection is established.
Flashes when the device
sending /receiving data. Flash
once per second while wi-fi
protected setup is in progress
Lit when the USB
device is ready.
Flashes when
sending /
receiving data.
Lit green
when there
are emails in
the inbox.
Lit green when
successfully connected
to an ADSL DSLAM
(“Line sync”)
Lit green when IP connected.
Flashes green when IP connected
and IP traffic is passing thru the
device. Lit red when device
attempted to become IP connected
and failed. Lit off in bridged mode or
when connection WAN is absent.
The Rear Ports
Connect the
antenna.
Connect the supplied RJ-11
(“telephone”) cable on this
port when connecting to the
ADSL/ telephone network.
Connect your computer
to a LAN port, using a
UTP Ethernet cable.
Connect the USB
cable on this port.
Press it to reset the
device or restore to
factory default settings.
Push WPS button to
trigger Wi-Fi Protected
Setup function*.
Connect the supplied
power adapter to this
jack.
Power ON/
OFF switch
* Note: For WPS configuration, please refer to the WPS section of User Manual.
2
Billion BiPAC 7402(G)X(L) Series ADSL2+ Router
Hardware Connection
Hardware Installation
1.
Power Connection
Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different country.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
3
Quick Start Guide
3. USB Connection
The USB 2.0 port supports 3G/ HSDPA modem connectivity: users can
conveniently access Internet via 3G, eliminating the limitations of the wired
network. This solution also employs an auto fail-over feature to ensure always-on
connectivity for SOHO users.
4. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other
side to the phone jack on the wall.
5. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.
4
Billion BiPAC 7402(G)X(L) Series ADSL2+ Router
6. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get
good speed/stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
Setup Utility
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.
5
Quick Start Guide
Connecting to the Router
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL linesync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual. If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
Billion Product Registration
Billion is committed to before and after sales customer services. You will get the most out of your Billion's products
after registration. Please register online at http://www.billion.com/register to receive valuable services and support
from us.
BiPAC 7402(G)X(L) Series V.101EN
6