Dancover Bioclimatic pergola gazebo San Pablo doors Manual

Manual
for
Gazebo San Pablo
3x3m, 3x4m and 4x4m
20-12-2023
Manual Instruction
Pergola
3x3m, 3x4m, 4x4m
1
Spare parts list
Label
No. Part description
Drawing
Qty
A
Column
4
B1
Beam (Left)
1
B2
Beam (Right)
1
C
Front and rear
beams
2
D
Middle beam
1
E
Flap
3x3=44
3x4=60
4x4=60
F
Column bottom
plate
4
G
Column cover
plate
4
H
Connectors
for middle
beams
2
I
Hinge ring
2
J
Hand crank
2
2
Label
No.
Part description
K1
Countersunk
head screw
K2
Qty
Drawing
M6x16
40+2
Pan head
screw
M6x16
20+2
K3
Flat washer
D6x12
8+2
K4
Screw+nut
M4x20
2
L
Woodworking
screw+plastic
expansion pipe
+Flat washer
+ screw cover
M
M8x80
10x50
8
16
1
Glass glue
3x3=88
N
Plastic jam
O
Corner support
K5
Self-drilling screw
ST 4.2x25
Q
Drainage connector
(Optional)
3x4=120
4x4=120
8
ST4.2x25
32
4
Please Note: O and K5 is an optional..., if you do need install them,
please refer to the last pages first.
The O and K5 should be removed if you need to install the screen set.
3
1. Connect the drainage connector Q with the column
Warm notice:
The drain connector Q is an optional accessory.
If it snows frequently and freezes in winter, it is
not recommended to install it because it will
block the water outlet.
Clamp the drainage connector Q into the column slot,
then connect the bottom plate with column A,
and tighten screws;
Complete four sets in sequence.
K1
QTY:16pcs F
QTY:4pcs
Q
QTY:4pcs
2. Match the connector H with one side of middle beam D,
then tighten the screw K1; then complete the other side.
K1
QTY:8PCS
H
5
5
QTY:2PCS
3. Put two hinge rings I into the gearbox drive shaft on the beam D,
fix the screw + nut K4
Step 2
Step 1
I
QTY:2PCS
K4
M4
6
M4x25
QTY:2 SETS
4. Place the column and beam as shown in the figure, and
note that the drain port of the column faces the same side;
Drain port
Drain port
Drain port
Drain port
7
7
5. The two ends of one front and rear
beam C are respectively placed on the
corner connectors on the column, and the
screws K1 are tightened;
Step 1
Step 2
QTY:4PCS
K1
8
6. The left and right beams B1/B2 are respectively placed on the corner
connectors on the column, and the screws K1 are tightened;
Step 2
Step 1
K1
QTY:8PCS
9
9
7. Insert ends of the other front and rear beams C
into the corner connectors on the
column, and tighten the screws K1;
K2
QTY:4PCS
10
8.The 4 column cover plates G
are respectively mounted on
the corner connectors of the
column and the beam,
and the screws K2
are tightened in turn;
Step 1
K2
QTY:12PCS
Step 2
G
11
QTY:4PCS
9. Adjust the position of the four columns so that they are perpendicular to the ground.
Meanwhile, the width of the top of each two columns should be measured
in accordance with the width of the bottom of each two columns.
Then use a market pen to mark 16 holes on the ground,
which should be corresponding to the holes in the botton palte.
Mark the location of the
hole on the ground with
a marker pen
Use tools: marker pen
(self-provided by installation workers)
12
10. Remove the product from the mark and drill holes of
at 16 mark positions on the ground with a percussion drill.
Drilling depth Ø10x80
Drilling quantity 16pcs
Use Tool: Percussion Bit Ø10
(Self-provided by Installation workers)
Use Tools: Percussion Drill
(Self-provided by Installation workers)
13
11. Place the plastic expansion pipe in the bottom hole of the column;
then move the product back to the hole drilled, align holes of the
column bottom plates with the hole drilled on the ground;
then set L1 into the woodworking screw L,
and fix it with the ground separately.
QTY:16PCS
14
12. Coat the glass glue M evenly on the drain of column and joints of beams.
QTY:1PCS
15
13. Place the middle beam D on the front and rear beams C.
16
14. Insert 6pcs flap (E) first (4pieces at gear box side and 2pcs at other side) on the
end of the brackets on both sides of the beams (B1-D and B2-D), and press down
on the slat as shown in the sketch below to secure it.
17
15. First, fix screw K2 with
gasket K3 align with hole
below the beam D,
then same to beam C.
Insert the other flap in turn.
Step 2
Step 1
QTY:8PCS
QTY:8PCS
18
16. Adjust according to below steps if the pergola can`t close completly
A: flap
B: flapsupport
Hole "A" and hole "B"
must be concentric
Adjust solution if hole"A" and hole "B" are not concentric
straight screwdriver
Hole "A“ and "B" are concentric
after adjusting
Adjusting the B flap support with
straight screwdriver as picture shown
19
17. Insert plastic jam N into two sides of each flap.
1. The following image shows how to
insert plastic jam into foremost flap.
2.Turn on the flap to half position, insert the plastic jam N into
hole of two ends of each flap in turn.
20
18. Put the hand crank J on, turn to open/close the flap; installation completed.
21
Install corner support (Optional)
Align the corner support O with
the bottom edge of the beam B1,
fix it with self-drilling screw K5,
install the remaining corner support in turn.
Tips：The O and K5 should be removed
if you need to install the screen set.
Following images are optional screen set
matched to pergola.
K5
QTY:32PCS
22
O
QTY:8PCS
Following images are optional screen set matched to pergola,
the O and K5 should be removed if you need to install the screen set.
Optional 1:
Screen/Sidewall
Optional 2:
Alu. turnover louvered wall
Optional 3:
Glass door
、
、
＼
＼
、
、
Contact information
Austria
Belgium
Croatia
Denmark
Estonia
Finland
France
Germany
Ireland
Italy
Latvia
Lithuania
Nederland
Norway
Poland
Portugal
Spain
Sweden
Switzerland
UK
For more information please visit: www.dancovershop.com