OPCOM Grow Wall3C Manual

Grow Wall3C
4. Ensure pH between 5.5-6.5 adjust by Soda (pH+)、Lemon(pH-).
For pH adjustment instruction, please refer to following Chart at below.
Grow Kits: B Scoop for Adjust of Nutritio (5g)
Satus
4.0-4.5
4.5-5.0
5.0-5.5
5.5-6.5
6.5-7.0
7.0-7.5
Soda (pH+)
Add 2.5g
Add 2g
Add 1g
Standard range
no Add
no Add
Lemon(pH-)
no Add
no Add
no Add
Standard range
Add 2.5g
Add 5g
B3. Growing Stage
1. When plants grow to over 2 inches height, switch control box to auto mode. Please refer to Chart II.
2. After 4-6 weeks, harvest the larger plants for consumption and keep smaller plants growing.
3. For time saving, sow the new seeds in sprout tray one week before you start next planting process. 4-6 weeks
C. Sprouts and Microgreens
Hydroponics Grow Wall 3C
1 week
Harvest
Cut off Large leaf
Keep
for regrow
1. Before you start next seedling, take advantage of the seedling tray for sprouts and microgreens. It takes 7-10 days to harvest.
2. Put seeds in warm water(recommeded temperature is 95 F , not over 104 F) for 24 hours.
3. Cover the sponges with wet paper towels.
4. Place the seedling tray with cover in the shade or cover it with black cloth.
5. After germination, during the growing stage, keep green sprout under the light and white sprout in the shade or cover it
with black cloth; in 7-10 days, you can harvest.
Day 0
Day 7-10
Day 1
Green sprout
D. Optional Accessories
White sprout
1. 500W Water Auto Heater
E. Maintenance
E1. Add Water
1. Measure the pH/EC value every 1-2 weeks and add water to maintain the vlaue balance.
E2. Change Water
1. After a cycle of planting, change the water and clean the unit.
2.When changing water, clean water gateway on each planting layers, you may also add moss detergent in the water tank to avoid the
moss remaining.
3. On the regular basis of every 1-2 weeks, clean the filtering sponge in the pump.
4. Regularly clean the filter sponge in each planting layer every 1 week.
E3. EC Meter Use and Calibration
1. Keep the electrode clean of EC meter and cover the electrode protective cap when not in use.
2. Turn off the meter when not in use for an extended amount of time.
F. Troubleshooting
Issue
Checkpoints / Solution
Make sure all power cables are connected.
Lamps not
Power button is ON.
lighting up
Make sure LED status is ON.
If it is on HI or LOW mode, the lamp has off time, during 24-hour cycle.
Pump has a
buzzing sound
Pump may make a buzzing sound in the beginning due to air inside the pump. After a minute with water
running through the pump, this sould be reduced.
The lamp/ pump
Control Box is designed with Auto, HI and LOW modes, which turn the lamps and the pump on and off
stop after hours
periodically.
Rotate the ring at the end of the pump clockwise or counterclockwise to get the most suitable water flow.
Water Over flows
Make sure it is not clogged at the water flowing gateway on each planting layer
CM
C
F1708038
P17092804
F1709051
P17103002
LT S D
TE
US
PATENT
Intertek
4010499
Manual
For more information, please visit
www.opcomfarm.com
Ver.: 202203
Grow Wall3C
16 Draining Water Tank:
Thank you for purchasing OPCOM Farm Grow Wall 3C, the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 144 plants capacity. Please read the quick guide carefully before setting it up.
For detailed user guide video, please visit Grow Wall 3C page at http://www.opcomfarm.com
A. Assembly
A1. Remove all the parts from box and check all the accessories
Fan socket
1. Open the water control box on the left side of the water tank by pulling
up the side planks. Take out the water drain pipe form the storing disk.
2.Prepare a water bucket with a capacity of around 40 L. Place the outlet of
thepipe un the bucket.
Turn On the pump and switch the water drain valve to Out to start draining.
3.Once finished draining, set everything back to default. (turn off the pump
and stop the water drain valve.)
Smart Control Box
fan beam
R3
column
L4 planting groove
Layer 3
LED
sockets
R2
column
L3 planting groove
L2 planting groove
Ribbon x10pcs
LED Growth Light x4pcs
Tube x4pcs
Base Stand
x2pcs
Maple plank
x2pcs
Power socket
cable x1pc
Screw pack
x1pc
Warranty Card
Manual Backup Pump x 1pc
AC/DC adapder x 1pc
power cable x1pc
Layer 1
LED
sockets
LED
Planting Tray(36 holes) x4pcs
Grow Sponge 60pk x9pcs
(OASP001)
planting basket
(25mm) x150pcs
Salt #1 (Nutrition) Soda (pH+) Lemon(pH-) B Scoop for Adjust
50ml x1
50ml x2
of Nutritio (5g)
250ml x2
Accessories
Alkaline
Neutral
Water
Spray x1pc
Remote
Controller x 1pc
Cleaning
ponge x1pc
Filter
Sponge x5pcs
Water tank
15
Operation
Sound
On
Off
On
Off
One Press
One Press
One Press
One Press
BB
B 1sec
BB
B 1sec
ON
High
Low
OFF
One Press
One Press
One Press
One Press
BB
BBB
BBBB
B 1sec
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
BB
BBB
BBBB
B 1sec
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
One Press
One Press
One Press
One Press
Light
Time
On (Follow last mode before turn off)
Off
12Hr/day ON mode of LED and 30mins/ 2Hr ON mode of Pump
Follow LED and Pump manual mode seting
always On
18Hr/day
9Hr/day
always Off
55mins/ 1Hr
25mins/ 30mins
5mins/ 30mins
always Off
Most plants can be grown using the AUTO mode.
Set up the Wake-up(automatically turns on everyday) and Sleeping(automatically turns off everyday) modes through lighting time setting.
A. When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset power on timeline.
B. When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset power off timeline.
Fan follow LEDon / off.
Restore factory settings after power failure.
Acidic
pH test
paper x1pc
Status
ON
High
Low
OFF
Pump
Seedling Tray x2pcs
(665*175*65mm)
EC Meter
x1pc
L1 planting groove
Fuction
Auto
Grow Kits
Layer 2
LED
sockets
Motor
socket
R1
column
Hose x 1pc
Control
box
socket
Pump
11 gallons
（40L）
Power
Remote Control
Control Box x 1pc
Water Cycling pipe
Water Cycling Valve
Water Drain Valve
Water Drain pipe
Chart I: Control Box Mode
Assembly
Layer 4
LED
sockets
16 Water Control Box
15
A2. Assemble GrowWall3
1
2
1 Assemble and secure the cross beam of the top fan and R3 colume with
screws.
2 Lift the wooden lid on top the fan's crossbeam. Plug the fan's power into
11
11
3
the fan socket, the first slot of the power socket cable, then close the lid.
3 Assemble the R3 column and the R2 column.
4 Hang the L4 planting groove and L3 planting groove on the columns
10
10
through the holes on the side planting grooves.Once hanged, set and
secure the clip onto the mechanism
4
10
10
5 Assemble the R2 column and the R1 column.
6 Assemble the L2 planting groove and the L1 planting groove on
the column.(see step.4)
4
4
7
7 Fix the power socket cable into the line groove in the column.
8 Stick the maple planks on the exterior of the assembled columns.
9
9
13
9 9.Set the LED grow light on the rocker arm on each layer of
columns. To set up, unscrew the thumb screw on the side of the
LED grow lights, remove the two circular spacers.
8
12
Place one spacer between the tip of the rocker arm and the side of the
LED grow light. Place another spacer between the thumb screw and the
tip of the rocker arm.
Once done, align the holes between each part and secure them with a
12
thumb screw.
10 Plug the power cord of the LED growth light into the LED socket of the
power socket cable on the column.
Organize the cables of the LED grow light and fix them in the line
12 Set the water tank under the L1 planting groove.
groove on the rocker arm.
Place the planting tray into the planting groove. Make sure
to correspond each water inlet of the planting tray to the
11 Dissembling the top and the bottom of the tube gives an aluminum
holes on the bottom of the planting groove.
and a plastic tube.
13 Set the plastic tube in the water inlet of the planting tray.
Face the teeth of the aluminum tube downwards, then, from the interior
Connect the tip of the aluminum tube at the bottom of the
of the planting groove, work the tube through the holes on the bottom.
planting groove by rotating.
cover the tip of the aluminum tube in the planting groove with a filter
14 Fill the water tank with 8gallons of water.
sponge.
15 Plug the AC/DC adapter into a the power socket cable, then
connect the AC/DC adapter with the power cable to power
up the machine.
G mode
5. LED light planting mode Control
L mode
S mode
figure 1
Off
1.Select the mode of the LED grow light (you may switch between modes through the button on the
left side of the LED lamp holder).
2.The light comes with four modes: G(in green), S(in orange), L(in orange), and Off(colorless)(see
figure 1).
Adjust the height of lighting
Adjust the angle of lighting
figure 2
3.Please note that the remote control could only adjust the duration of lighting (On/ Hi /Low /Off),
as shown in chart 1. To switch between the mode of the LED grow light, please access the buttons on the light tubes manually.
4.Height of the LED grow light: Adjust the height and the angle of lighting manually through the rocker arm(see figure 2).
5.This hydroponics system comes with fans that improve the air circulation and accelerate the cooling of the LED tubes, which increases
the ventilation and avoids plants from overheating. Please make sure to keep a 5-10 cm distance between the light tube and the
plants to further prevent plants from overheating. To boost the light intensity in a power-saving way, direct the light at both the plant
and the wall simultaneously, which could add 30% more lighting to the plants.
Please read and follow every steps to avoid any malfunction.
B. Seedling
B1. Germination Stage
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)
3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray
(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and
ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
4. Place the seedling tray with cover in the shade.(Fig3)
5. Suggest using Watering Spray water to sponges and keep them wet everyday.
6. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and move them into product (make
sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.
7. Discard unsprouted sponges after regular germination time.
8. In each sponge, keep strong plants and cut the other weak plants.
* Different plant may have different germination time, please check before plant.
Chart II: Plant Stage
(Fig1）
This side up!
(Fig2）
(Fig3)
(Fig4)
Basil, Lemon Balm
Planting Time
LED Mode
Pump Mode
Nutrition
T( )
RH
EC
pH
Germination Stage
Day 0~7
-
-
-
68 - 77
80%
0.5-1.0
5.5-6.5
Young Plant Stage
Day 3~14
ON
ON
Need
59 - 86
45%-70%
1.0-2.0
5.5-6.5
Growing Stage
After Day 14
Auto
Auto
Need
59 - 86
45%-70%
1.0-2.0
5.5-6.5
* Please keep the seeds in refrigerator if you don’t use it, recommended temperture is 41 - 50.
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com and read “Plant Q&A”.
B2.Young Plant Stage
1. Add 10.5 gallons water to the water tank.
2. During Young Plant Stage, turn on LED and Pump. Please refer to the ChartII.
3. Add Salt #1 (Nutrition) into the water tank and ensure EC value between(=1.0-2.0mS/cm)
Grow Kits: B Scoop for Adjust of Nutritio (5g)
Status
0.0-0.5
0.5-1.0
1.0-1.5
over 2.0
Salt #1 (Nutrition)
Add 2g
Add 1g
Standard range
Add water
Notes
Be sure each sponge is fully wet in
seedling tray.