Barbas Unica-2 55 * User Manual

INSTRUCTIONS FOR USE &
MANUAL DAILY MAINTENANCE
UNICA-2 55
Gas fire with open combustion system
Bellfires wishes you many cosy evenings with your new Bellfires gas fire
This document is an essential part of your gas fire.
Read it carefully before use of the gas fire and keep it in a safe place!
Serial number:
Production date:
Bellfires
English
BELLFIRES GAS FIRE WITH OPEN COMBUSTION SYSTEM:
Unica-2 55
Instructions for use
(UNC-2 55)
3
Bellfires
4
English
Instructions for use
Bellfires
English
CONTENTS
Page
1. WARRANTY TERMS .................................................................................
7
2. INSTRUCTIONS FOR USE .......................................................................
9
3. USING THE APPLIANCE FOR THE FIRST TIME .....................................
30
4. DAILY MAINTENANCE ..............................................................................
31
5. ANNUAL MAINTENANCE ..........................................................................
32
Instructions for use
5
Bellfires
6
English
Instructions for use
Bellfires
1
English
WARRANTY TERMS
Interfocos
Warranty terms
Interfocos B.V. guarantees the quality of the supplied Bellfires hearth and the quality
of the materials used. All Bellfires hearths are developed and manufactured according
to the highest possible quality standards. If, despite all this, something should prove
amiss with the Bellfires hearth you have purchased, Interfocos B.V. offers the following
manufacturer’s warranty.
Article 1: Warranty
1.1. If Interfocos B.V. determines that the Bellfires hearth you have purchased is
defective as a result of a flaw in the construction or material, Interfocos B.V.
guarantees to repair or replace the hearth free of charge, without charging any
costs for labour or spare parts.
1.2. Repair or replacement of the Bellfires hearth will be undertaken by Interfocos B.V.
or by a Bellfires dealer as designated by Interfocos B.V.
1.3. This warranty is supplementary to the existing legal national warranty of Bellfires
dealers and Interfocos B.V. in the country of purchase and is not intended to
restrict your rights and claims based on the applicable legal provisions.
Article 2: Warranty conditions
2.1. Should you wish to claim under the warranty, please contact your Bellfires dealer.
2.2. Complaints should be reported as quickly as possible after they have manifested
themselves.
2.3. Complaints will only be accepted if they are reported to the Bellfires dealer,
together with the serial number of the Bellfires hearth which is stated on the front
of the instructions for use.
2.4. In addition, the original receipt (invoice, receipt, cash receipt) showing the date of
purchase must also be submitted.
2.5. Repairs and replacements during the warranty period do not give any entitlement
to an extension of the warranty period. After a repair or replacement of warranty
parts, the warranty period shall be deemed to have started on the date of
purchasing the Bellfires hearth.
2.6. If a certain part is eligible for the warranty and the original part is no longer
available, Interfocos B.V. shall ensure that an alternative part of at least the
same quality shall be provided.
Article 3: Warranty exclusions
3.1. The warranty on the Bellfires hearth ceases to be in effect if:
a. it is not installed according to the supplied installation instructions, and to
national and/or local regulations;
b. it has been installed, connected or repaired by a non-Bellfires dealer;
Instructions for use
7
Bellfires
English
c.
d.
e.
3.2.
it has not be used or maintained according to the instructions for use;
it has been changed, neglected or roughly treated;
it has been damaged as a result of external causes (outside the hearth
itself), for example, lightning strike, water damage or fire;
In addition, the warranty lapses if the original purchase receipt shows any
change, deletion, removal or if it is illegible.
Article 4: Warranty area
4.1. The warranty is only valid in those countries where Bellfires hearths are sold
through an official dealer network.
Article 5: Warranty period
5.1. This warranty will only be granted during the warranty period.
5.2. The body of the Bellfires hearth is guaranteed for a period of 10 years against
construction and/or material faults, starting from the moment of purchase.
5.3. For other parts of the Bellfires hearth, a similar warranty applies from the moment
of purchase for a period of one year.
5.4. For user parts such as glass, glass (cord), thermocouple and the interior of the
combustion chamber, a similar guarantee is given until after the first burning.
Article 6: Liability
6.1. A claim granted by Interfocos B.V. under this warranty does not automatically
imply that Interfocos B.V. also accepts liability for any possible damage.
The liability of Interfocos B.V. never extends further than that stated in these
warranty conditions. Any liability of Interfocos B.V. for consequential damage is
expressly excluded.
6.2. That stated in this provision is not valid if and to the extent that is derives from
a mandatory provision.
6.3. All agreements entered into by Interfocos B.V. are, unless specifically stated
otherwise in writing and to the extent that they are permitted based on applicable
law, subject to the Conditions of the Dutch Metal and Engineering Association
(METAALUNIEVOORWAARDEN), as filed with the registrar of the Court of
Rotterdam on 1 January 2014.
Interfocos B.V.
Hallenstraat 17
5531 AB Bladel
The Netherlands
Tel: +31-497339200
Email: info@Bellfires.com
Carefully retain the instructions for use; they show the serial number of the hearth.
You will need this if you wish to claim under the warranty.
8
Instructions for use
Bellfires
English
2
INSTRUCTIONS FOR USE
2.1
INTRODUCTION
Congratulations on your purchase of this modern Bellfires gas fire with an open
combustion system.
This quality product will provide you with many years of enjoyment due to the flame
effect and warmth that it provides.
Please read the instructions for use carefully before using the appliance for the first
time. Keep this booklet in a safe place.
2.2
BUILT-IN PROTECTION OF THE APPLIANCE
The appliance is fully protected by means of a thermo-electric pilot light shut off in the
event of a gas escape from the main burner. Furthermore, the appliance is fitted with
an “oxy-stop” pilot flame that shuts down the burner if the flue gas is insufficiently
exhausted.
This atmosphere protection; the “oxy-stop” pilot light, should not replace an independently installed carbon monoxide detector.
2.2.1 Safety
Do not place embers, vermiculite granules, wood logs or pebbles against
the pilot light burner. Make sure that the pilot flame can burn at all times
freely over the main burner. Only in this way is proper ignition of the main
burner ensured.
Ignoring these directions could lead to a dangerous situation.
Do not place flammable objects within 100 cm of the appliance. Pay
special attention to furnishings and ornaments around the fire.
When igniting the pilot light and burner, always keep a minimum
distance of 100 cm from the front of the appliance.
If the pilot flame goes out for any reason, wait for 5 minutes before
attempting to re-light it.
It is essential that the appliance, the flue and the burner air intake are
cleaned and inspected annually by a recognised fitter/gas specialist.
The safe operation of the appliance will thus remain guaranteed. For this,
please refer to the Installation instructions (Chapter 2: Maintenance),
that are supplied separately with each appliance.
The gas fire must never be used with the door open or the door glass
removed.
Instructions for use
9
Bellfires
English
Never place flammable material on the ceramic log set.
The filling of the main burner with embers and wood logs, or pebbles,
may not under any circumstances be changed or added to.
Do not place easily-flammable materials, such as nylon clothing or
flammable liquids, in the vicinity of the gas fire.
Ensure at all times that children and other people who are not
aware of the operation of the gas appliance are only in the vicinity
of the appliance exclusively under supervision.
Use a fireguard to protect the people and children mentioned
above against possible burns.
2.3
OPERATION: REMOTE CONTROL
Remote control
Standard appliance
Remote control
Appliance equipped with ambient
lighting and/or convection fan (option)
Figure 1: Remote control
10
Instructions for use
Bellfires
English
2.3.1 General
Read these instructions carefully before lighting the fire !!
The appliance is opperated by radio remote control.
This comprises a hand-held transmitter and a receiver. The receiver is part of the gas
control block assembly.
The receiver and the gas control block are under in the appliance.
Electrical connections and batteries:
Standard appliance:
Hand-held
transmitter
2x 1.5V battery
Type LR03 or AAA
Receiver
4x 1.5V battery
Type LR06 or AA
Option:
6VDC adapter (230VAC).
Available from your fitter.
Note: Remove batteries from receiver!
The appliance is supplied with ambient lighting and/or convection fan:
Hand-held
transmitter
2x 1.5V batterij
Type LR03 or AAA
Receiver
6VDC
via the 5 wire cable
from the Light-Module
Module - Light and/or
Convection fan
230 VAC
Note:
No batteries in the
receiver. *)
*) During a power outage, you can temporarily install batteries in the receiver so that
the appliance continues to operate.
Note: Hand-held transmitter and receiver are not interchangeable with previous models.
The pilot light is situated in the front of the burner, behind a cowl. Should the pilot light
go out, you must wait five (5) minutes before attempting to re-ignite the fire.
Important
Once the fire is lit, it must burn at maximum for approx. 10 minutes to allow the chimney
to come up to temperature!
Instructions for use
11
Bellfires
English
2.3.2 Hand-held transmitter
The remote control works by radio signal. The hand-held transmitter is configured in the
factory with a unique signal code.
Hand-held transmitter standard
Hand-held transmitter including
operation ambient lighting and/or
convection fan (option)
Figure 2: Hand-held transmitter
12
Instructions for use
Bellfires
English
Signal
Indicator
Time
Child proof
Thermostatic Mode
Battery Status
Countdown
Timer
Fahrenheit or
Celsius:
°F/12 hour or
°C/24 hour
Program
Mode
Eco Mode
Temperature
-Symbol:
has no function for the appliance
Display hand-held transmitter standard
Child proof
Signal
Indicator
Time
Thermostatic Mode
Battery Status
Countdown
Timer
Fan-Symbol:
Operating convection
fan (option)
Fan speed levels:
1 to 4 bars
Program
Mode
Fahrenheit or Celsius:
°F/12 or °C/24 hour
Temperature
-Symbol:
has no function
for the appliance
Eco Mode
Light-Symbol:
Operation Ambient
lighting/Dimmer.
(option)
Display hand-held transmitter including operation ambient lighting and/or
convection fan (option)
Figure 3: Display hand-held transmitter
Instructions for use
13
Bellfires
English
AM
PM
ON
OFF
SETTING FAHRENHEIT OR CELSIUS
• To change between °C and °F, press
buttons simultaneously.
and
1 2
Note:
Choosing °F results in a 12 hour clock.
Choosing °C results in a 24 hour clock.
AM
PM
ON
OFF
1 2
AM
PM
ON
OFF
1 2
SETTING THE TIME
• Pres and buttons simultaneously.
Day flashes.
• Press or button to select a number to
correspond with the day of the week (e. g.
1= Monday, 2 = Tuesday, 3 = Wednesday,
4 = Thursday, 5= Friday, 6 = Saturday,
7= Sunday).
• Press and buttons simultaneously.
Hour flashes.
• To select hour press or button.
• Press and buttons simultaneously.
Minutes flash.
• To select minutes press and button.
• To confirm press and buttons
simultaneously or wait.
CHILD PROOF
ON:
• To activate press and buttons
simultaneously.
•
displayed and the hand-held transmitter is
rendered inoperable, except for the off function.
OFF:
• To deactivate press
simultaneously.
•
disappears.
14
and
buttons
Instructions for use
Bellfires
English
IMPORTANT: SETTING UP SIGNAL CODE BEFORE USING THE APPLIANCE
FOR THE FIRST TIME
Before the appliance can be used, the receiver must first learn the hand-held
transmitter’s signal code.
• Press the “RESET” button on the receiver, and keep this pressed until 2 beeps are
heard. See figure 4.
Release the “RESET” button after the second (somewhat longer) beep.
• Press, within 20 seconds, the button (small flame) on the hand-held transmitter,
until 2 short beeps are heard. The signal code has now been set up on the receiver.
If, however, a single long beep is heard, this means that setting the signal code
has failed or that the wiring has been connected incorrectly.
You only need to set up the signal code once. It is not necessary when changing the
batteries of the hand-held transmitter or receiver.
Figure 4: Receiver “RESET” button
Instructions for use
15
Bellfires
English
2.3.3 Operation (Remote control)
MANUAL MODE (HAND-HELD TRANSMITTER)
SWITCH ON THE APPLIANCE / IGNITING THE FIRE
• Open the gas supply valve in the gas pipe to the fire.
Warning
When the pilot light is ignited, the motor turns
automatically to maximum flame height.
AM
PM
ON
OFF
1 2
Hand-Held Transmitter One-Button Operation
(Default Setting)
• Press button until two short beeps and a
blinking series of lines confirms the start
sequence has begun; release button.
• Main gas flows once pilot ignition is confirmed.
• Hand-held transmitter automatically goes into
Manual Mode after main burner ignition.
Note
Change from one-button to two-button ignition operation by pressing
and holding button for 10 sec. immediately after installing batteries.
ON is displayed and 1 is flashing. When change is complete 1 will
change to 2.
16
Instructions for use
Bellfires
English
AM
PM
ON
OFF
1 2
Hand-Held Transmitter Two-Button Operation
• Press and button simultaneously until
two short beeps and a blinking series of lines
confirms the start sequence has begun; release
buttons.
• Main gas flows once pilot ignition is confirmed.
• Hand-held transmitter automatically goes into
Manual Mode after main burner ignition.
Note
Change from two-button to one-button ignition operation by pressing
and holding button for 10 sec. immediately after installing batteries.
ON is displayed and 2 is flashing. When change is complete 2 will
change to 1.
Important:
•
•
•
•
If the pilot flame goes out for any reason, wait for 5 minutes
before attempting to re-light it.
If the pilot light does not ignite after 3 ignition attempts;
close the gas tap and warn the fitter.
Once the pilot light is burning, the main burner must ignite
within 10 seconds automatically.
If this does not happen, immediately close the gas tap and
warn the fitter.
If the main burner ignites with a pop; immediately close the
gas tap and warn the fitter.
Instructions for use
17
Bellfires
English
Pilot gas adjustment screw
(Factory set) (Puncture the casing
with a small screwdriver)
Adjustment screw
Maximum burner pressure
(Factory set and sealed)
Motor-knob
8-wire Receiver Jack
Microswitch
Figure 5: Gas regulating block
• Possible error messages:
* 3 seconds: short beeps, audible when the motor-knob operates:
Receiver batteries need changing soon (having heard this signal, the
appliance can be ignited another ten times approximately).
* 5 seconds: unbroken beeps:
Error. For example, one of the cables may not be properly connected.
Important:
If the pilot flame goes out, then wait for
at least 5 minutes before repeating the
above procedure.
STAND-BY MODE (PILOT LIGHT)
AM
PM
• Press button and hold to set appliance to
pilot light.
ON
OFF
1 2
We recommend to let the pilot light
burn in the winter months, to prevent
condensation on the inside of the glass.
18
Instructions for use
Bellfires
English
SETTING THE FLAME HEIGHT / EXTINGUISHING THE FIRE (STAND-BY)
AM
PM
ON
OFF
1 2
AM
Gradually decrease flame height / Extinguishing
the fire
• After ignition, the burner automatically sets the
flames to the maximum height.
• Press button to lower the flames and to turn
off the burner. (Extinguishing the fire: Press
button and hold: pilot light remains burning
(standby position)!)
(Pressing briefly the button gradually lowers
the flames to the low position.)
Flame height directly to minimum position
• Pressing the button twice, automatically
lowers the flames to the low position. (When this
happens, the flames will first automatically go
to maximum!) This is indicated by “ ” on the
display.
Note: Backlight must be on for high fire and
low fire double-click operation!
2x
AM
PM
ON
OFF
1 2
Instructions for use
Gradually increase flame height
• Press button and hold to increase the flame
level and to turn on the burner from the stand-by
position.
(Pressing briefly the button gradually
increases the flames to the high position.)
19
Bellfires
English
AM
2x
Flame height directly to maximum position
• Pressing the button twice automatically
increases the flames to the high position.
This is indicated by “ ” on the display.
Note: Backlight must be on for high fire and
low fire double-click operation!
Important:
•
•
If you turn on the burner by pressing the button, it must
ignite within 10 seconds.
If this does not happen, immediately close the gas tap and
warn the fitter.
If the burner ignites with a pop; immediately close the gas
tap and warn the fitter.
LIGHT / DIMMER OPERATION (Option)
AM
ON
• Press
button.
•
displayed.
• Light is on at preset level.
OFF
• Press
button.
•
disappears.
SETTING
• Press
button and hold until flashes.
• To adjust light between 20…100 % press or
button.
• To confirm setting either press
button or
wait.
•
displayed.
Note:
The Light works independently of the Pilot flame. If you want the light on but no flame,
press button. If the main burner and pilot light are switched off, with button, the
light will switch off automatically.
20
Instructions for use
Bellfires
English
CONVECTION FAN OPERATION (OPTION)
AM
The convection fan turns automatically ON and OFF
and has 4 rotational speeds which can be adjusted
from low (1 bar) to high (4 bars).
SETTING
1. Press
button and hold until
flashes.
2. Press button to increase fan speed and
button to decrease fan speed.
button or wait.
3. To confirm setting either press
4. The symbol
displayed.
ON
1. The convection fan will automatically turn ON
about 4 minutes after the main burner is ignited,
on maximum fan speed and after 10 seconds will
revert to the set fan speed.
OFF
1. It is not possible to switch the convection fan
OFF while the main burner is on.
2. The convection fan turns OFF automatically
about 10 minutes after the main burner has been
turned off.
3. The pilot light can continue burning or be turned
off.
Instructions for use
21
Bellfires
English
COUNTDOWN TIMER
AM
PM
ON
OFF
1 2
ON / SETTING
• Press button and hold until displayed, and
hour flashes.
• To select hour press or button.
• To confirm press button. Minutes flash.
• To select minutes press or button.
• To confirm press button or wait.
OFF
• Press
button,
and countdown time disappear.
Note:
At end of countdown time period, the fire turns
completely off. The Countdown Timer only works in
Manual, Thermostatic, and Eco Modes. Maximum
countdown time is 9 hours and 50 minutes.
TURNING OFF THE APPLIANCE COMPLETELY
AM
PM
ON
OFF
Hand-held transmitter
• Press button to turn off.
• If the appliance is not to be used for some time,
please close the gas supply valve in the gas pipe.
1 2
Note:
There is a 5 seconds delay before the next ignition
is possible.
Important:
22
If the pilot flame goes out for any reason,
wait for 5 minutes before attempting to
re-light it.
Instructions for use
Bellfires
English
MODES OF OPERATION
AM
PM
ON
OFF
1 2
AM
PM
ON
OFF
Thermostatic Mode
The room temperature is measured and compared
to the set temperature. The flame height is then
automatically adjusted to achieve the set
temperature.
Program Mode
PROGRAMS 1 and 2, each can be programmed to
go on and off at specific times at a set temperature.
1 2
AM
Instructions for use
Eco Mode
Flame height modulates between high and low.
If the room temperature is lower than the set
temperature, the flame height stays on high for a
longer period of time. If the room temperature is
higher than the set temperature, the flame height
stays on low for a longer period of time. One cycle
lasts approx. 20 min.
23
Bellfires
English
THERMOSTATIC MODE
AM
PM
ON
OFF
ON
button.
1. Press
2. displayed, preset temperature displayed briefly,
and then room temperature displayed.
1 2
OFF
1. Press
2. Press
3. Press
4. Press
AM
PM
ON
OFF
1 2
Important:
24
button.
or button to enter Manual Mode.
button to enter Program Mode.
button to enter Eco Mode.
SETTING
button and hold until displayed,
1. Press
temperature flashes.
2. To adjust set temperature press or button.
3. To confirm press
button or wait.
Place the hand-held transmitter in a place that is not
influenced by direct sunlight, draught, heat from
the appliance and other heat sources.
Instructions for use
Bellfires
English
PROGRAM MODE
AM
PM
ON
OFF
ON
button.
1. Press
2. , 1 or 2, ON or OFF displayed.
OFF
1. Press
2. Press
3. Press
1 2
or or button to enter Manual Mode.
button to enter Thermostatic Mode.
button to enter Eco Mode.
Note:
The set temperature for Thermostatic Mode is the temperature for the on time in
Program Mode. Changing the Thermostatic Mode set temperature also changes the on
time temperature in Program Mode.
Default settings
ON TIME (Thermostatic) TEMPERATURE: 21 °C (70 °F)
OFF TIME TEMPERATURE: “ ” (pilot light only)
AM
PM
ON
OFF
1 2
TEMPERATURE SETTING
1. Press
button and hold until
flashes.
ON and set temperature (setting in Thermostatic
Mode) displayed.
button or wait.
2. To continue press
, OFF displayed, temperature flashes.
3. Select off temperature by pressing the or
button.
4. To confirm press
button.
Note:
The on (Thermostatic) and off set temperatures are the same for each day.
Instructions for use
25
Bellfires
English
AM
PM
ON
OFF
1 2
DAY SETTING
5.
flashes. Press or button to choose
between
,
, 1, 2, 3, 4, 5, 6, 7.
button.
6. To confirm press
selected
AM
PM
ON
OFF
1 2
AM
PM
ON
OFF
1 2
26
ON TIME SETTING
(PROGRAM 1)
, 1, ON displayed,
is displayed shortly,
7.
and hour flashes.
8. To select hour press or button.
9. To confirm press
button.
, 1, ON displayed,
displayed shortly,
and minutes flash.
10. To select minutes press or button.
button.
11. To confirm press
OFF TIME SETTING
(PROGRAM 1)
12.
,1, OFF displayed,
is displayed shortly,
and hour flashes.
13. To select hour, press or button.
14. To confirm press
button.
, 1, OFF displayed,
displayed shortly,
and minutes flash.
15. To select minutes press or button.
button.
16. To confirm press
Instructions for use
Bellfires
English
Note:
Either continue to PROGRAM 2 and set on and off times or stop programming at this
point, and PROGRAM 2 remains deactivated.
Note:
,
PROGRAM 1 and 2 use the same on (Thermostatic) and off temperatures for
and Daily Timer (1, 2, 3, 4, 5, 6, 7).
Once a new on (Thermostatic) and / or off temperature has been set, that temperature
becomes the new default setting.
Note:
If
,
or Daily Timer are programmed for PROGRAM 1 and PROGRAM 2 on and
off times, these become the new default times. The batteries must be removed to clear
the PROGRAM 1 and PROGRAM 2 on and off times and temperatures.
or Daily Timer (1, 2, 3, 4, 5, 6, 7) selected
• Set on time and off time using same procedure as “
selected” (above).
•
: Set on time and off time for both Saturday and Sunday.
• Daily Timer: Unique on and off times may be set for a single day of the week, for
multiple days of the week, or for every day of the week.
• Wait to finish setting.
ECO MODE
AM
ON
• Press button to enter Eco Mode.
• The symbol
appears.
OFF
• Press button.
• The symbol
disappears.
Instructions for use
27
Bellfires
English
Faults
• If the signals from the hand-held transmitter do not seem to be reaching the receiver,
the cause may be:
* Spent batteries: replace the batteries.
* An electronic problem: press the “RESET” button on the receiver.
• If the appliance regularly switches itself off, please contact your installer.
Replacing the batteries
• If the batteries are inserted incorrectly, the electronics or drive may be irreparably
damaged.
• Only replace the batteries when the appliance has been completely switched off.
Standard appliance:
• The hand-held transmitter/receiver batteries have a service life of approx. one year.
We recommend you use alkaline batteries.
Rechargeable batteries are not permitted.
• If the receiver’s batteries are nearly empty, the system will turn the appliance off
completely. This will not occur if the receiver is connected to an AC power adaptor
(6V) (option).
• The batteries must be replaced whenever:
1 Hand-held transmitter : The battery symbol indicates this in the display.
: Battery fully charged
: Battery empty
2 Receiver: 3 seconds: short beeps, audible when the motor-knob operates.
1 Hand-held transmitter:
* Open the cover on the back of the transmitter.
* Remove the batteries from the battery compartment.
* Place two new 1.5V batteries (LR03 or AAA type) as indicated in the battery
compartment.
* Close the cover.
2 Receiver:
* Carefully pull the receiver assembly out of the compartment, behind the facade
of the appliance.
* Open the cover.
* Remove the batteries from the battery compartment.
* Place four new 1.5V batteries (LR06 or AA type) as indicated in the battery
compartment. The negative end (-) of the battery must always be at the contact
spring end of the compartment.
* Close the cover and place the receiver back in its holder.
28
Instructions for use
Bellfires
English
The appliance is supplied with ambient lighting and/or convection fan:
• Receiver:
Because the appliance is equipped with a 230 VAC connection, no batteries are
present in the receiver.
• Hand-held transmitter:
The hand-held transmitter batteries have a service life of approx. one year.
We recommend you use alkaline batteries. Rechargeable batteries are not permitted.
Replacement of the batteries is necessary when the battery symbol indicates this in
the display.
: Battery fully charged
: Battery empty
* Open the cover on the back of the transmitter.
* Remove the batteries from the battery compartment.
* Place two new 1.5V batteries (LR03 or AAA type) as indicated in the battery
compartment.
* Close the cover.
Instructions for use
29
Bellfires
3
English
USING THE APPLIANCE FOR THE FIRST TIME
The gas fire is coated with a lacquer layer resistant to high temperature. During the first
hours of operation, the burning in of the lacquer may result in an unpleasant smell. This
is harmless, however. Operating the gas fire at full capacity for a few hours, while
ventilating the room, will eliminate the smell.
After using your gas fire for the first few times, you may be aware of a light deposit on
the inside off the glass. This is caused by the paint curing. Once your fireplace has
cooled down, this deposit can be removed with glass cleaner or ceramic hob cleaner.
30
Instructions for use
Bellfires
4
English
DAILY MAINTENANCE
• Ensure that as little dust, and as few particles of cigarette smoke, candles and oil
lamps as possible pollute the air in the room in which the appliance is used. Heating
of these particles by the convection system of the appliance could lead to
discoloration of the walls and ceiling. It is therefore very important to ensure that the
room in which the appliance is located is sufficiently ventilated. Regularly remove
any dust deposits from behind the facade (top and bottom sides) by means of a
vacuum cleaner.
Important:
•
Regularly clean the glass on the inside of the appliance with
glass spray or ceramic hob cleaner. (See installation instructions
for dismantling/assembling the glass.)
Attention ! •
•
•
If the glass is not cleaned on time, this can result
in becoming dull and difficult, if not impossible, to
clean.
Careful with glass cleaner ! Make sure that no
glass cleaner liquid flows in the sealing of the
inside of the glass pane at the bottom of the door.
Spray each time a little glass cleaner liquid on the
glass, and polish it off immediately.
Glass cleaner liquid in the sealing of the door can
cause dissolving of the black border on the inside
of the glass. It will become very spotty and can’t
be repaired.
If the glass is broken or cracked, it must be immediately
replaced before operating the gas fire again.
Broken ceramic heat-resistant glass may not be
disposed in a glass recycling container, but must
be included in normal household waste.
• If anything is spilt on the fire, switch it off immediately and wait for it to cool
down sufficiently before cleaning. Never use scouring powder, aggressive
cleaners or fire polish on the gas fire. Use only a dry lint free cloth.
• Heat resistant lacquer in aerosols can be obtained from your
distributor. During the yearly maintenance, the lacquer can be used to repair
small areas of damage.
Instructions for use
31
Bellfires
5
English
ANNUAL MAINTENANCE
It is essential that the appliance, the flue and the
burner air intake are cleaned and inspected annually
by a recognised fitter/gas specialist.
The safe operation of the appliance will thus remain
guaranteed.
Please refer also to the Installation instructions that are
supplied separately with each appliance.
32
Instructions for use
Bellfires
Instructions for use
English
33
Bellfires
34
English
Instructions for use
Your Bellfires dealer
01 - 261015 - 341466