Rockwell Automation 20A-DG01 User Manual
Rockwell Automation 20A-DG01 is a safety option for PowerFlex 40P and PowerFlex 70 AC drives, providing a 'Safe Torque Off' (STO) function. It meets safety standards like EN ISO 13849-1, Category 3 / PL (d) and SIL CL 2, ensuring safe operation in industrial applications. The 20A-DG01 works in conjunction with other safety components to prevent the drive from generating torque in the connected motor, thus safeguarding personnel and equipment in hazardous situations.
PDF
Download
Document
Advertisement
Advertisement
User Manual Original Instructions Safe Torque Off Option (Series B) for PowerFlex 40P and PowerFlex 70 Enhanced Control AC Drives Catalog Number 20A-DG01 Topic Page Summary of Changes 2 General Description 3 What Is the DriveGuard Safe Torque Off Option? 3 Certifications and Compliance 4 CE Certification 5 Certified Equipment 6 Important Safety Considerations 6 Safe State 7 Safety Category 3 / PL (d) Performance Definition 7 Stop Category Definitions 8 Performance Level and Safety Integrity Level (SIL) CL2 8 PFDavg and PFH Definitions 8 PFDavg and PFH Data 9 Functional Proof Tests 10 Contact Information if Safety Option Failure Occurs 10 Installation and Wiring 11 Pre-Installation Instructions 11 EMC Considerations 12 DriveGuard Safe Torque Off Option Installation 13 Wiring 16 Verify Operation 17 Description of Operation 19 PowerFlex 40P Safe Torque Off Operation 19 PowerFlex 70 Safe Torque Off Operation 20 Connection Examples 21 Summary of Changes Summary of Changes Change Updated Certifications and Compliance sections 2 See Page… 5 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 General Description General Description The DriveGuard® Safe Torque Off option, when used with PowerFlex® 40P or PowerFlex 70 drives together with other safety components, provides a safety function which inhibits torque generation in the motor(s) powered by the drive. When used with PowerFlex 40P or PowerFlex 70 drive, the DriveGuard Safe Torque Off option has been certified to meet the requirements for SIL 2 according to EN/IEC 61800-5-2 and IEC 61508, and PL (d) and Category 3 according to EN ISO 13849-1. The DriveGuard Safe Torque Off option is just one component in a safety control system. Components in the system must be chosen and applied appropriately to achieve the desired level of safeguarding. What Is the DriveGuard Safe Torque Off Option? The DriveGuard Safe Torque Off option: • Provides the “Safe torque off (STO)” function defined in EN/IEC 61800-5-2. • Blocks gate firing signals from reaching the IGBT output power devices of the drive. This prevents the IGBT’s from switching in the sequence necessary to generate torque in the connected motor. • Can be used in combination with other safety devices to fulfill the requirements of a system “safe torque off” function which satisfies Category 3 / PL (d) according to EN ISO 13849-1 and SIL CL 2 according to EN/IEC 62061, IEC 61508, and EN/IEC 61800-5-2. IMPORTANT This option is suitable for performing only mechanical work on the drive system or affected area of a machine. It does NOT disconnect or isolate the drive power output to the motor. This option should not be used as a control for normal starting and/or stopping the drive. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 3 General Description ATTENTION: Electrical Shock Hazard. Verify that all sources of AC and DC power are de-energized and locked out or tagged out in accordance with the requirements of ANSI/NFPA 70E, Part II. ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC and -DC terminals or test points (see your drive User Manual for locations). The voltage must be zero. ATTENTION: In Safe Torque Off mode, hazardous voltages may still be present at the motor. To avoid an electric shock hazard, disconnect power to the motor and verify that the voltage is zero before performing any work on the motor. ATTENTION: In the event of the failure of two output IGBT's in the drive, when the DriveGuard Safe Torque Off option has controlled the drive outputs to the off state, the drive may provide energy for up to 180° of rotation in a 2-pole motor before torque production in the motor ceases. Certifications and Compliance TUV Rheinland EC Type Examination Certification TUV Rheinland has certified the DriveGuard Safe Torque Off option, when used in a PowerFlex 70 or PowerFlex 40P drive, is compliant with the requirements for machines defined in Annex I of the EC Directive 2006/42/EC, and that it complies with the requirements of the relevant standards listed below. • EN ISO 13849-1 Safety of machinery - Safety related parts of control systems Part 1: General principles for design (DriveGuard Safe Torque Off option + drive achieves Category 3 / PL (d)) • EN/IEC 61800-5-2 Adjustable speed electrical power drive systems - Part 5-2 Safety requirements - Functional (DriveGuard Safe Torque Off option + drive achieves SIL CL 2) • EN/IEC 62061 Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems • IEC 61508 Part 1-7 Functional safety of electrical/electronic/programmable electronic safety-related systems TUV also certifies that the DriveGuard Safe Torque Off option may be used in applications up to Category 3 / PL (d) according to EN ISO 13849-1 and SIL 2 according to EN/IEC 62061 / IEC 61508 / EN/IEC 61800-5-2. TUV Rheinland certifications may be found at rok.auto/certifications. 4 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 General Description UL Certification The PowerFlex 40P, PowerFlex 70, and DriveGuard Safe Torque Off option have been listed with UL as compliant with UL 508C. Canadian Certification The PowerFlex 40P, PowerFlex 70, and DriveGuard Safe Torque Off option have been listed (cUL) as compliant with C22.2 No 14. RCM Certification Rockwell Automation declares the PowerFlex 40P (240V AC, 480V AC), PowerFlex 70 (240V AC, 400V AC, 480V AC), and DriveGuard Safe Torque Off option compliant with the Radiocommunications Act:1992 (including Amendments up to 2018), the Radiocommunications (Electromagnetic Compatibility) Standard 2017, and the Radiocommunications Labeling (Electromagnetic Compatibility) Notice 2017 as demonstrated by compliance with IEC 61800-3 Adjustable speed electrical power drive systems Part 3: EMC requirements and specific test methods. CE Certification LV Directive 2014/35/EU Rockwell Automation declares the PowerFlex 40P and PowerFlex 70 drives compliant with the CE LV Directive as demonstrated by compliance with the requirements of EN 61800-5-1 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal, and energy. The DriveGuard Safe Torque Off Option Kit is not within the scope of the Low Voltage Directive. EMC Directive 2014/30/EU Rockwell Automation declares the PowerFlex 40P (240V AC, 480V AC), PowerFlex 70 (240V AC, 400V AC, 480V AC), and DriveGuard Safe Torque Off option compliant with the CE EMC Directive as demonstrated by compliance with the requirements of EN 61800-3 Adjustable speed electrical power drive systems Part 3: EMC requirements and specific test methods. Machinery Directive 2006/42/EC TUV Rheinland, Notified Body Identification Number 0035, certifies the DriveGuard Safe Torque Off option compliant with the CE Machinery Directive as demonstrated by compliance with the requirements of EN ISO 13849-1, EN/IEC 61800-5-2, and EN/IEC 62061. TIP If the encoder interface option is installed on the PowerFlex 70, the product will not have CE certification. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 5 General Description Certified Equipment Drive PowerFlex 40P PowerFlex 70 Enhanced Control Rating (AC) 240V 480V 240V 400V 480V TUV Certified Yes Yes Yes Yes Yes DriveGuard Safe Torque Off Function Series B or greater Series B or greater Series A or greater Series A or greater Series A or greater ATTENTION: Hazard of injury exists due to electric shock. Only install a Series B or greater DriveGuard Safe Torque Off option in a PowerFlex 40P Drive. Certifications Online See the Product Certifications link at rok.auto/certifications. for Declarations of Conformity, Certificates, and other certifications details. Important Safety Considerations The system user is responsible for: • • • • • • • • The set-up, safety rating, and validation of any sensors or actuators connected to the system. Completing a system-level risk assessment and reassessing the system any time a change is made. Certification of the system to the desired safety performance level. Project management and proof testing. Programming the application software and the safety option configurations in accordance with the information in this manual. Access control to the system, including password handling. Analyzing all configuration settings and choosing the proper setting to achieve the required safety rating. In circumstances where external influences (for example falling or suspended loads) are present, additional measures (for example mechanical brakes) can be necessary to prevent any hazard. IMPORTANT When applying Functional Safety, restrict access to qualified, authorized personnel who are trained and experienced. ATTENTION: When designing your system, consider how personnel will exit the machine if the door locks while they are in the machine. Additional safeguarding devices may be required for your specific application. 6 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 General Description Safe State The DriveGuard Safe Torque Off option is intended for use in safety-related applications where the de-energized state is the safe state. All of the examples in the Description of Operation section are based on achieving the de-energization as the safe state. Safety Category 3 / PL (d) Performance Definition To achieve Safety Category 3 / PL (d) according to EN ISO 13849-1, the safety-related parts have to be designed such that: • The safety-related parts of machine control systems and/or their protective equipment, as well as their components, shall be designed, constructed, selected, assembled, and combined in accordance with relevant standards so that they can withstand expected conditions. • Well tried safety principles shall be applied. • A single fault in any of its parts does not lead to a loss of safety function. • Some but not all faults will be detected. • The accumulation of undetected faults can lead to loss of safety function. • Short circuits in the external wiring of the safety inputs is not one of the faults that can be detected by the system, therefore, according to EN ISO 13849-2, these cables must be installed so as to be protected against external damage by cable ducting or armor. • Whenever reasonably practical a single fault shall be detected at or before the next demand of the safety function. • The average diagnostic coverage of the safety-related parts of the control system shall be low. • The mean time to dangerous failure of each of the redundant channels shall be low to high. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 7 General Description Stop Category Definitions The selection of a stop category for each stop function must be determined by a risk assessment. • Stop Category 0 is achieved with immediate removal of power to the actuator, resulting in an uncontrolled coast to stop. See “Description of Operation” Example 1 on page 21. • Stop Category 1 is achieved with power available to the machine actuators to achieve the stop. Power is removed from the actuators when the stop is achieved. See “Description of Operation” Example 2 on page 22. IMPORTANT When designing the machine application, timing and distance should be considered for a coast to stop: • Stop Category 0 or Safe Torque Off • Stop Category 1 or Safe Stop 1 - Time Controlled For more information regarding stop categories, see EN/IEC 60204-1 or IEC 61800-5-2. Performance Level and Safety Integrity Level (SIL) CL2 For safety-related control systems, Performance Level (PL), according to EN ISO 13849-1, and SIL levels, according to IEC 61508 and EN/IEC 62061, include a rating of the system’s ability to perform its safety functions. All of the safety-related components of the control system must be included in both a risk assessment and the determination of the achieved levels. See the EN ISO 13849-1, IEC 61508, and EN/IEC 62061 standards for complete information on requirements for PL and SIL determination. PFDavg and PFH Definitions Safety-related systems can be classified as operating in either a Low Demand mode, or in a High Demand/Continuous mode. 8 • Low Demand mode: where the frequency of demands for operation made on a safety-related system is no greater than one per year or no greater than twice the proof-test frequency. • High Demand/Continuous mode: where the frequency of demands for operation made on a safety-related system is greater than once per year or greater than twice the proof test interval. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 General Description The SIL value for a low demand safety-related system is directly related to order-of-magnitude ranges of its average probability of failure to satisfactorily perform its safety function on demand or, simply, average probability of failure on demand (PFDavg). The SIL value for a High Demand/Continuous mode safety-related system is directly related to the probability of a dangerous failure occurring per hour (PFH). PFDavg and PFH Data These PFDavg and PFH calculations are based on the equations from Part 6 of IEC 61508 and show worst-case values. This table provides data for a 20-year proof test interval and demonstrates the worst-case effect of various configuration changes on the data. PowerFlex 40P PFDavg and PFH for 20-year Proof Test Interval Attribute PFDavg PFH SFF Test Result 1.74E-05 2.0E-10 81% PowerFlex 70 PFDavg and PFH for 20-year Proof Test Interval Attribute PFDavg PFH SFF Test Result 3.4E-05 3.9E-10 81% Terminology Abbreviation PFDavg PFH SFF Full Term Probability of Failure on Demand Probability of Failure per Hour Safe Failure Fraction Definition The average probability of a system to fail to perform its design function on demand. The probability of a system to have a dangerous failure occur per hour. The sum of safe failures plus the sum of dangerous detected failures divided by the sum of all failures. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 9 General Description Functional Proof Tests The functional safety standards require that functional proof tests be performed on the equipment used in the system. Proof tests are performed at user-defined intervals and are dependent upon PFDavg and PFH values. IMPORTANT Your specific application determines the time frame for the proof test interval. Contact Information if Safety Option Failure Occurs If you experience a failure with any safety-certified device, contact your local Rockwell Automation distributor. With this contact, you can: 10 • Return the device to Rockwell Automation so the failure is appropriately logged for the catalog number affected and a record is made of the failure. • Request a failure analysis (if necessary) to determine the probable cause of the failure. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Installation and Wiring Installation and Wiring Care should be taken to follow drive instructions for EMC and environmental compliance. See the following list of manuals for specific instructions: • PowerFlex 70 Adjustable Frequency AC Drive User Manual, publication 20A-UM001 • PowerFlex 70 Adjustable Frequency AC Drive Installation Instructions, publication 20A-IN009 • PowerFlex 40P User Manual, FRN 3, publication 22D-UM001 • PowerFlex 40P AC Drive Technical Data, publication 22D-TD001 Pre-Installation Instructions Installation must be in accordance with the following steps and must be carried out by competent personnel. The DriveGuard Safe Torque Off option is intended to be part of the safety related control system of a machine. Before installation, a risk assessment should be performed that compares the DriveGuard Safe Torque Off option specifications and all foreseeable operational and environmental characteristics of the machine to which it is to be fitted. In no case should be DriveGuard Safe Torque Off option be used in a PowerFlex 40P or PowerFlex 70 drive where the maximum surrounding air temperature, shock, or vibration specifications of the drive are exceeded. PowerFlex 70 Maximum Surrounding Air Temperature without derating: IP20, NEMA/UL Type 1: Flange Mount: IP66, NEMA/UL Type 4X/12: PowerFlex 40P Maximum Surrounding Air Temperature without derating: IP20, Open Type: IP30, NEMA 1, UL Type 1: Flange and Plate Mount: Both Drives Shock: Vibration: 0…50 °C (32…122 °F) 0…50 °C (32…122 °F) 0…40 °C (32…104 °F) -10…50 °C (14…122 °F) -10…40 °C (14…104 °F) Heatsink: -10…40 °C (14…104 °F) Drive: -10…50 °C (14…122 °F) 15 g peak for 11 ms duration (1.0 ms) 0.152 mm (0.006 in.) displacement, 1 g peak Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 11 Installation and Wiring A safety analysis of the machine section controlled by the drive is required to determine how often the safety function should be tested for proper operation during the life of the machine. ATTENTION: The following information is merely a guide for proper installation. Rockwell Automation, Inc. cannot assume responsibility for the compliance or the noncompliance to any code, national, local or otherwise for the proper installation of this equipment. A hazard of personal injury and/or equipment damage exists if codes are ignored during installation. EMC Considerations The DriveGuard Safe Torque Off option and PowerFlex 40P and PowerFlex 70 drives may be installed in an industrial electromagnetic environment which is consistent with the “Second Environment” described in IEC 61800-3 and where the EMC requirements documented in the PowerFlex 40P and PowerFlex 70 Installation manuals have been satisfied. Important installation requirements include: 12 • All motor output, control (I/O) and signal wiring for the drive and DriveGuard Safe Torque Off option must be shielded cable. • Grounding (earthing) must conform to the requirements described in the drive user manuals. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Installation and Wiring DriveGuard Safe Torque Off Option Installation PowerFlex 40P Drives 1. Remove all power to the drive. ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC and -DC terminals or test points, the voltage must be zero. See the PowerFlex 40P User Manual, publication 22D-UM001 for additional information. 2. Remove the protective plug covering the PowerFlex 40P Safe Torque Off connector shown in Figure 1. Figure 1 - PowerFlex 40P Protective Plug 3. Remove the PowerFlex 40P Safe Torque Off connection jumper shown in Figure 2. Figure 2 - PowerFlex 40P Safe Torque Off Connection Jumper Location Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 13 Installation and Wiring 4. Remove the PowerFlex 40P Hardware Enable jumper shown in Figure 3. Figure 3 - PowerFlex 40P Hardware Enable Jumper Location The PowerFlex 40P hardware enable jumper must be removed when using the DriveGuard Safe Torque Off option. Failure to remove the jumper will cause the drive to fault when a start command is issued. IMPORTANT 5. Plug the DriveGuard Safe Torque Off option (Series B or greater) into the PowerFlex 40P four pin Safe Torque Off connector as shown in Figure 4. Figure 4 - PowerFlex 40P Safe Torque Off Connector 0.8…1.1 N•m (7…10 lb•in) 6. Tighten screw to 0.8…1.1 N•m (7…10 lb•in). 14 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Installation and Wiring PowerFlex 70 Enhanced Control Drives 1. Remove the PowerFlex 70 Safe Torque Off Connection jumper as shown in Figure 5. Figure 5 - PowerFlex 70 Safe Torque Off Connection Jumper Location (Typical) 2. Remove the PowerFlex 70 Hardware Enable jumper as shown in Figure 6. Figure 6 - PowerFlex 70 Hardware Enable Jumper Location (Typical) IMPORTANT The PowerFlex 70 hardware enable jumper must be removed when using the DriveGuard Safe Torque Off option. Failure to remove the jumper will cause the drive to fault when a start command is issued. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 15 Installation and Wiring 3. Plug the DriveGuard Safe Torque Off option (Series A or greater) into the PowerFlex 70 four-pin connector as shown in Figure 7. Figure 7 - PowerFlex 70 Safe Torque Off Connector 0.8…1.1 N•m (7…10 lb•in) 4. Tighten screw to 0.8…1.1 N•m (7…10 lb•in). Wiring Important points to remember about wiring: • Always use copper wire. • Wire with an insulation rating of 600V or greater is recommended. • Control wires should be separated from power wires by at least 0.3 m (1 ft). DriveGuard Safe Torque Off Option Terminal Block Specifications Wire Size Range (1) Maximum 2 1.5 mm (16 AWG) Torque Minimum Maximum Recommended 0.14 mm2 0.25 N•m (2.2 lb•in) 0.22 N•m (1.9 lb•in) (26 AWG) (1) Maximum / minimum that the terminal block will accept - these are not recommendations. Wire Types Wire Type(s) Description Unshielded Per US NEC or applicable national — or local code Shielded 16 Multi-conductor shielded cable such as Belden 8770(or equiv.) 0.750 mm2 (18AWG), 3 conductor, shielded. Minimum Insulation Rating 300V, 60 °C (140 °F) Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Installation and Wiring DriveGuard Safe Torque Off Option Terminal Description 43 21 No. Signal Description 1 Monitor - N.C. 2 Common - N.C. Normally closed contacts for monitoring relay status. Maximum Resistive Load: 250V AC / 30V DC / 50 VA / 60 Watts Maximum Inductive Load: 250V AC / 30V DC / 25 VA / 30 Watts 3 +24V DC 4 24V Common Connections for user supplied power to energize coil. 33.3 mA typical, 55 mA maximum. Verify Operation Test the safety function for proper operation after the initial installation of the DriveGuard Safe Torque Off option. Retest the safety function at the intervals determined by the safety analysis described on page 11. Verify that both safety channels are functioning according to the PowerFlex 40P Channel Operation and Verification or PowerFlex 70 Channel Operation and Verification on page -18. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 17 Installation and Wiring PowerFlex 40P Channel Operation and Verification Safety Function Status Drive In Safe State Drive In Stopped State Drive In Stopped State Drive Able To Run Safety Channel Operation Safe Torque Off Option Terminals 3 and 4 No Power Applied Power Applied No Power Applied Power Applied PowerFlex 40P Enable Input No Power Applied No Power Applied Power Applied Power Applied Description For Verification Safe Torque Off Option Monitor Contact Terminals 1 and 2 Closed Open Closed Open PowerFlex 40P [Control In Status] Parameter 13, Bit 2 Value = 0 Value = 0 Value = 1 Value = 1 PowerFlex 40P Comms Status Word 8448, Bit 0 Value = 0 Value = 0 Value = 0 Value = 1 Safe Torque Off Output (1) Relay N.O. Dig Output States Closed Open Open Open (1) Must set A055 [Relay Out Sel], A058 or A061 [Opto Outx Sel] to option 25 “Safe-Off”. PowerFlex 70 Channel Operation and Verification Safety Function Status Drive In Safe State Drive In Stopped State Drive In (1) Stopped State Drive Able To Run Safety Channel Operation Safe Torque Off Option Terminals 3 and 4 No Power Applied Power Applied No Power Applied Power Applied PowerFlex 70 Enable Input No Power Applied No Power Applied Power Applied Power Applied Description For Verification Safe Torque Off Option Monitor Contact Terminals 1 and 2 Closed Open Closed Open PowerFlex 70 Drive Inhibits Parameter 214, Bit 2 Value = 1 Value = 1 Value = 0 Value = 0 (1) 18 A Start/Run command will cause an F111 “Enable Hardware” fault. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Description of Operation Description of Operation PowerFlex 40P Safe Torque Off Operation The DriveGuard Safe Torque Off option for PowerFlex 40P (see Figure 8) disables the drive’s output IGBT’s by breaking the link with the drive microcontroller. When used in combination with a second safety channel (the Enable input), the system satisfies the requirements of EN ISO 13849-1, Category 3 / PL (d) for Safe Torque Off and helps protect against restart. Under normal drive operation, the Safe Torque Off relay is energized, the enable input is energized, and the drive is able to run. If either inputs is de-energized, the gate control circuit is disabled. To meet EN ISO 13849-1, Category 3 / PL (d) operation, both safety channels must be de-energized. See the following examples for details. IMPORTANT By itself, the Safe Torque Off option initiates a coast-to-stop action. Additional protective measures will need to be applied when an application requires a change to the stop action. Figure 8 - PowerFlex 40P Drive Safe Torque Off Circuitry AC Line Input Power PowerFlex 40P AC Drive +24V DC Stop Start Gate Control From Microcontroller Safe Off Option 4 Safety Channel 3 2 1 Gate Control Circuit Common Safety Channel Enable M Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 19 Description of Operation PowerFlex 70 Safe Torque Off Operation The PowerFlex 70 DriveGuard Safe Torque Off option (see Figure 9) disables the drive’s output IGBT’s by disconnecting the gate control power supply. When used in combination with a second safety channel (the Enable input), the system satisfies the requirements of EN ISO 13849-1, Category 3 / PL (d) for Safe Torque Off and helps protect against restart. Under normal drive operation, the Safe Torque Off relay is energized, the enable input is energized, and gate control power is available to the gate control circuit. If either of these inputs is de-energized, the gate control circuit is disabled. To meet EN ISO 13849-1, Category 3 / PL (d) operation, both safety channels must be de-energized. See the following examples for details. IMPORTANT By itself, the Safe Torque Off option initiates a coast-to-stop action. Additional protective measures will need to be applied when an application requires a change to the stop action. Figure 9 - PowerFlex 70 Drive Safe Torque Off Circuitry AC Line Input Power PowerFlex 70 AC Drive +24V DC Stop Start Gate Control Power Supply Safe Off Option 4 Safety Channel 3 2 1 Gate Control Circuit Common Safety Channel Enable M 20 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Description of Operation Connection Examples Example 1 - Safe Torque Off Connection with Coast-to-Stop Action, Dual Channel Figure 10 - Stop Category 0 – Coast AC Line Input Power PowerFlex AC Drive +24V DC +24V DC GuardMaster Trojan Gate Stop Stop A1 S21 S13 31 13 23 X1 Minotaur MSR9T A2 S22 S14 Start Start Safe Off Option 32 14 24 X2 4 3 +24V DC Common 2 1 Common Enable * IMPORTANT The drive Enable digital input is a solid state circuit. The safety outputs on safety module must not be configured for Pulsed/Safety Pulse Test. M Circuit Status Circuit shown with guard door closed and system ready for normal drive operation. Operating Principle This is a dual channel system with monitoring of the Safe Torque Off circuit and drive. Opening the guard door will switch the input circuits (S13…S14 and S21…S22) to the Minotaur™ monitoring safety relay unit. The output circuits (13…14 and 23…24) will cause the Safe Torque Off option and drive Enable circuit to trip and the motor will coast to stop. To restart the drive, the Minotaur safety relay must first be reset followed by a valid start command to the drive. Fault Detection A single fault detected on the Minotaur safety input circuits will result in the lock-out of the system at the next operation and will not cause loss of the safety function. If the Safe Torque Off option sticks On, the motor will stop on command due to the enable input. The system cannot be reset when this fault condition exists. Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 21 Description of Operation Example 2 - Safe Torque Off Connection with Time Controlled Stop Action, Dual Channel Figure 11 - Stop Category 1 - Time Controlled AC Line Input Power GuardMaster Trojan PowerFlex AC Drive Gate +24V DC +24V DC A1 S21 S11 S52 S12 S22 37 47 57 13 23 S33 S34 X1 X2 X3 X4 Y39 Y40 38 48 58 14 24 Y2 Y1 Minotaur MSR138DP A2 Stop Stop Start Start Safe Off Option +24V DC Common 4 3 2 1 IMPORTANT The drive Enable digital input is a solid state circuit. The safety outputs on safety module must not be configured for Pulsed/Safety Pulse Test. Common Enable * M Circuit Status Circuit shown with guard door closed and system ready for normal drive operation. Operating Principle This is a dual channel system with monitoring of the Safe Torque Off circuit and drive. Opening the guard door will switch the input circuits (S11…S12 and S21…S22) to the Minotaur monitoring safety relay unit. The output circuits (13…14) issue a Stop command to the drive and cause a controlled deceleration. After the programmed delay, the timed output circuits (47…48 and 57…58) will cause the Safe Torque Off option and the drive Enable circuit to trip. If the motor is rotating when the trip occurs, it will coast to stop. To restart the drive, the Minotaur safety relay must first be reset followed by a valid start command to the drive. Fault Detection A single fault detected on the Minotaur safety input circuits will result in the lock-out of the system at the next operation and will not cause loss of the safety function. If the Safe Torque Off option sticks On, the motor will stop on command due to the enable input. The system cannot be reset when this fault condition exists. The function is considered Safe Stop 1 time controlled (SS1-t per IEC 61800-5-2; 4.2.3.3). The controlled deceleration can fail undetected. The safety function will only guarantee a coast to stop after the programmed delay. This function cannot be used if a failure to initiate a controlled deceleration can cause a hazard in the final application. 22 Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 Description of Operation Notes: Rockwell Automation Publication PFLEX-UM003D-EN-P - June 2021 23 Rockwell Automation Support Use these resources to access support information. Technical Support Center Find help with how-to videos, FAQs, chat, user forums, and product notification updates. rok.auto/support Knowledgebase Access Knowledgebase articles. rok.auto/knowledgebase Local Technical Support Phone Numbers Locate the telephone number for your country. rok.auto/phonesupport Literature Library Find installation instructions, manuals, brochures, and technical data publications. rok.auto/literature Product Compatibility and Download Center (PCDC) Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes. rok.auto/pcdc Documentation Feedback Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback. Waste Electrical and Electronic Equipment (WEEE) At the end of life, this equipment should be collected separately from any unsorted municipal waste. Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec. Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback. For technical support, visit rok.auto/support. Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752, İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur Allen-Bradley, DriveGuard, expanding human possibility, Minotaur, PowerFlex, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. *PN-631486* PN-631486 Publication PFLEX-UM003D-EN-P - June 2021 | Supersedes Publication PFLEX-UM003C-EN-P - October 2020 Copyright © 2021 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A. ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Safe Torque Off (STO) function
- SIL CL 2 certified
- Category 3 / PL (d) compliant
- Dual safety channel operation
- Coast-to-stop action
- PowerFlex 40P and 70 compatibility
Frequently asked questions
It's a safety feature designed to prevent torque generation in a motor connected to a PowerFlex 40P or 70 drive, ensuring safety in hazardous situations.
It meets EN ISO 13849-1, Category 3 / PL (d) and SIL CL 2, providing a high level of safety in industrial environments.
It disables the drive's output IGBTs by breaking the link with the drive microcontroller, preventing torque generation. It requires two safety channels to be de-energized for safe operation.
By itself, it initiates a coast-to-stop action. Additional protective measures may be required for applications requiring a different stop action.