Ryobi HP962 Operator`s manual

OPERATOR’S MANUAL
CORDLESS DRILL-DRIVER
MODEL NOS. HP962 / HP1202M
10
MODEL HP962
5
10
5
MODEL HP1202M
THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER.
Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator's manual before using your new cordless drill-driver.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless drill-driver properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
■
General Safety Rule ................................................................................................................................................ 2-3
■
Specific Safety Rules/Symbols ................................................................................................................................ 3-5
■
Features ..................................................................................................................................................................... 5
■
Specifications ............................................................................................................................................................. 6
■
Important Information For Recharging Hot Batteries .................................................................................................. 6
■
Disposal Of The Exhausted Battery ............................................................................................................................ 6
A. Battery Pack Preparation For Recycling ............................................................................................................... 6
■
Operation ............................................................................................................................................................... 7-12
■
Maintenance ............................................................................................................................................................. 13
■
Parts Ordering / Service ........................................................................................................................................... 14
GENERAL SAFETY RULES
Personal Safety
WARNING:
■
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
■
■
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
■
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
■
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery. Use battery only
with charger listed.
■
BATTERY
HP962
HP1202M
1311146
1311148
■
■
■
MODEL
■
■
CHARGING ASSEMBLY
1411140
1411141
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack listed.
Page 2
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on, invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations. Do not use
on a ladder or unstable support.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
GENERAL SAFETY RULES
■
Tool Use and Care
■
■
■
■
■
■
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer
at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool before making any
adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce risk of
starting the tool accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
■
■
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may create a risk of injury when
used on another tool.
Service
■
■
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
or heat. This will reduce the risk of explosion and
possibly injury.
Additional Rules For Safe Operation
■
■
Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
WARNING:
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light. To
reduce the risk of serious personal injury, never use any
cordless product in the presence of open flame. An
exploded battery can propel debris and chemical. If
exposed, flush with water immediately.
■
■
Important Rules for Battery Tools
■
■
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when
not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire
■
Page 3
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than 50°F
but less than 100°F. Do not store outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and
water, then neutralize with lemon juice or vinegar. If
liquid gets into your eyes, flush them with clean
water for at least 10 minutes, then seek immediate
medical attention. Following this rule will reduce the risk
of serious personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
■
WARNING:
A damaged battery is subject to explosion. To avoid
serious personal injury, properly dispose of a damaged
battery.
■
Important Safety Instructions For Charger
■
■
■
■
■
■
■
■
Save these instructions. This manual contains important safety and operating instructions for charger.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire, or
serious personal injury.
To reduce risk of injury, charge only nickel-cadmium
and nickel metal hydride type rechargeable batteries. Other types of batteries may burst causing
personal injury and damage. Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.
Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress. Following this rule will reduce the risk
of serious personal injury.
An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
Note: AWG = American Wire Gage
■
■
■
Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock
or fire. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
To reduce the risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Disconnect charger from power supply when not in
use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
DANGER:
RISK OF ELECTRIC SHOCK. DO NOT TOUCH
UNINSULATED PORTION OF OUTPUT CONNECTOR
OR UNINSULATED BATTERY TERMINAL.
■
Page 4
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic of current
---
Direct Current
Type or a characteristic of current
n0
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
Safety Alert Symbol
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock
and personal injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
SAVE THESE INSTRUCTIONS
Page 5
SPECIFICATIONS:
HP962
HP1202M
Chuck
3/8 in. Keyless
3/8 in. Keyless
Motor
DC Motor 9.6V
DC Motor 12.0V
Switch
Variable Speed
Variable Speed
No Load Speed
0 - 550 RPM
0 - 550 RPM
Clutch
24 Positions
24 Positions
Charger Input
120V, 60 Hz, AC Only
120V, 60 Hz, AC Only
Charge Rate
3-6 Hours
3-6 Hours
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your drill-driver continuously, the batteries in
your battery pack become hot. You should let a hot battery
pack cool down for approximately 30 minutes before attempting to recharge.
Note: This situation occurs when continuous use of your
drill-driver causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "Charging
Your Drill-Driver" for normal recharging of batteries. If the
charger/charging assembly does not charge your battery
pack under normal circumstances, return both the battery
pack and charger/charging assembly to your nearest Ryobi
Authorized Service Center for electrical check.
DISPOSAL OF THE EXHAUSTED BATTERY
1.8
00
N i Cd
37
C YC
R ER B R CL E
.822.88
To preserve natural resources, please
recycle or dispose of properly.
This product contains nickel-cadmium
battery. Local, state, or federal laws may
prohibit disposal of Nickel-Cadmium
batteries in ordinary trash.
BATTERY PACK PREPARATION FOR RECYCLING
Consult your local waste authority for information regarding
available recycling and/or disposal options.
For more information on battery recycling call 1-800-8
BATTERY.
WARNING:
Upon removal, cover the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its
components. Also, never touch both terminals with metal
objects and/or body parts, as short circuit may result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
WARNING:
Do not attempt to disassemble the battery pack. Fire or
injury may result.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields. Always wear eye protection which is marked
to comply with ANSI Z87.1.
Page 6
OPERATION
Before attempting to use any tool, familiarize yourself with all
operating features and safety requirements.
LEVEL
TORQUE
ADJUSTMENT
RING
10
KNOW YOUR DRILL-DRIVER
See Figure 1.
5
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict severe injury.
CHARGING YOUR DRILL-DRIVER
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it overnight prior to use.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by recharging) for them to fully charge.
KEYLESS
CHUCK
SWITCH
TRIGGER
■
■
■
■
■
■
■
■
DIRECTION OF
ROTATION
SELECTOR
BATTERY
PACK
MAG TRAY™
(Model HP1202M)
Fig. 1
TO CHARGE
■
BIT
STORAGE
AREA
Charge battery pack only with the charging assembly
provided.
Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only.
Connect charging assembly to power supply.
Place battery pack in charging assembly. Align raised
rib on battery pack with groove in charging assembly.
See Figure 2.
Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging assembly. When properly connected, red light on charging
assembly will turn on.
Note: During the two year warranty period, if the charge
indicator light (LED) fails to come on or goes out while
charging battery pack, return charging assembly and
battery pack to your nearest authorized service center
for repair or replacing.
After normal usage, 3 hours or less of charging time is
required to fully recharge battery pack. Note: If battery
pack is completely discharged, 6 hours or longer of
charging time is required to fully recharge battery
pack.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
DO NOT place charging assembly in an area of extreme heat or cold. It will work best at normal room
temperature.
When battery pack has been charged, disconnect charging assembly from power supply and remove the battery pack. This practice will increase battery life.
Page 7
BATTERY
PACK
CHARGING
ASSEMBLY
CHARGE
INDICATOR
LIGHT (LED)
Fig. 2
OPERATION
REVERSE
WARNING:
DIRECTION OF
ROTATION
SELECTOR
10
If any parts are missing, do not operate tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
53
SWITCH
See Figure 3.
Your drill starts and stops by depressing and releasing the
switch trigger.
Your drill has a variable speed feature in the switch. The
switch delivers higher speed and torque with increased
trigger pressure. Speed is controlled by the amount of
switch trigger depression.
CENTER POSITION
(LOCK)
SWITCH
TRIGGER
FORWARD
SWITCH LOCK
See Figure 3.
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use. To lock the switch trigger, place the direction
of rotation selector in the center position.
Fig. 3
■
Place the direction of rotation selector in center position. See Figure 3.
■
Place the battery pack in your drill. Align raised rib on
battery pack with groove in drill's battery port. See Fig-
5
10
TO INSTALL BATTERY PACK
ure 4.
■
Make sure the latches on each side of your battery pack
snap in place and that battery pack is secured in drill
before beginning operation.
TO REMOVE BATTERY PACK
■
■
■
Place the direction of rotation selector in center position. See Figure 3.
Locate latches on side of battery pack and depress both
sides to release battery pack from your drill. See Figure 4.
Remove battery pack from your drill.
BATTERY
PACK
CAUTION:
When placing battery pack in your drill, be sure raised
rib on battery pack aligns with groove in drill's battery
port and latches snap in place properly. Improper
assembly of battery pack can cause damage to internal
components.
BATTERY
PORT
LATCHES
DEPRESS
LATCHES TO
RELEASE
BATTERY PACK
Fig. 4
Page 8
OPERATION
REVERSIBLE
See Figure 3.
RELEASE (UNLOCK)
CHUCK BODY
5
10
This tool is reversible. The direction of rotation is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch for
drilling. The drilling direction is reversed when the selector is
to the right of the switch. When the selector is in center
position, the switch trigger is locked.
CAUTION:
CHUCK
COLLAR
GRIP
(TIGHTEN)
To prevent gear damage, always allow chuck to come to
a complete stop before changing the direction of rotation.
Fig. 5
To stop, release switch trigger and allow the chuck to come
to a complete stop.
CHUCK BODY
10
CHUCK JAWS
WARNING:
5
Battery tools are always in operating condition. Therefore,
switch should always be locked when not in use or when
carrying at your side.
DRILL BIT
KEYLESS CHUCK
See Figure 5.
CHUCK COLLAR
RIGHT
Fig. 6
5
10
A keyless chuck has been provided with your drill to allow for
easy installation and removal of bits. As the name implies,
you can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand. Rotate
the chuck body with your other hand. The arrows on the
chuck indicate which direction to rotate the chuck body in
order to GRIP (tighten) or RELEASE (unlock) the drill bit.
WARNING:
Do not hold the chuck body with one hand and use the
power of the drill to tighten chuck jaws on drill bits. Chuck
body could slip in your hand or your hand could slip and
come in contact with rotating drill bit. This could cause
an accident resulting in serious personal injury.
WRONG
INSTALLING BITS
■
Place the direction of rotation selector in center position.
See Figure 3. This will turn off the power to your drill.
■
Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend to
use. Also, raise the front of your drill slightly to keep the
bit from falling out of the chuck jaws.
■
Insert your drill bit into the chuck the full length of the
jaws. See Figure 6.
Tighten the chuck jaws on the drill bit. To tighten, grasp
and hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
■
Fig. 7
Note: Rotate the chuck body in the direction of the arrow
marked GRIP to tighten the chuck jaws. DO NOT use a
wrench to tighten or loosen the chuck jaws.
WARNING:
Do not insert drill bit into chuck jaws and tighten as shown
in figure 7. This could cause drill bit to be thrown from
drill resulting in possible serious personal injury or
damage to the chuck.
Page 9
OPERATION
■
■
SCREWDRIVING
TORQUE ADJUSTMENT
(Driving power of your drill-driver)
When using your drill-driver for various driving aplications, it
becomes necessary to increase or decrease the torque in
order to help prevent the possibility of damaging screw
heads, threads, workpiece, etc. In general, torque should
correspond to the intensity of the screw diameter. If the
torque is too high or the screws too small, the screws may be
damaged or broken.
The torque is adjusted by rotating the torque adjustment ring.
See Figure 8. The torque is greater when the torque adjustment ring is set on a higher setting. The torque is less when
the torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and the
size of screw you are using.
TO DECREASE
TORQUE
5
■
■
Place the direction of rotation selector in center position.
See Figure 3. This will turn off the power to your drill.
Loosen the chuck jaws from drill bit.
To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other hand.
Note: Rotate chuck body in the direction of the arrow
marked RELEASE to loosen chuck jaws.
DO NOT use a wrench to tighten or loosen the chuck jaws.
Remove drill bit from chuck jaws.
10
■
TORQUE
ADJUSTMENT
RING
TO INCREASE
TORQUE
Fig. 8
SCREWDRIVER BITS
10
REMOVING BITS
See Figure 6.
■
■
Identify the twenty four torque indicator settings located
on the front of your drill. See Figure 8.
Rotate adjustment ring to the desired setting.
• 1-4
For driving small screws.
• 5-8
For driving screws into soft material.
• 9 - 12 For driving screws into soft and hard
materials.
• 13 - 16
For driving screws in hard wood.
• 17 - 20
• 21 -
For driving large screws.
For heavy drilling.
5
TO ADJUST TORQUE
BIT
STORAGE
AREA
Fig. 9
20
BIT STORAGE
See Figure 9.
When not in use, bits provided with your drill can be placed
in the storage area located on the top of your drill as shown
in figure 9.
20
LEVEL DRILLING
See Figure 10.
LEVEL
A convenient new feature provided with your drill is a level.
It is recessed in the motor housing on top of your drill. It can
be used to keep drill bit level during drilling operations.
Fig. 10
Page 10
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating tool. Failure to do so could result
in objects being thrown into your eyes, resulting in
possible serious injury.
DRILLING
See Figure 11.
15
When drilling hard, smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
lower speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate your
drill at lower speed until the hole is started.
The material to be drilled should be secured in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
20
WARNING:
Fig. 11
MODEL HP1202M
5
10
Be prepared for binding or bit breakthrough. When these
situations occur, the drill has a tendency to grab and kick
opposite to the direction of rotation and could cause loss
of control when breaking through material. If you are not
prepared, this loss of control can result in possible serious
injury.
When drilling metals, use a light oil on the drill bit to keep it
from overheating. The oil will prolong the life of the bit and
increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release switch
trigger immediately. Remove the bit from the workpiece and
determine the reason for jamming.
MAG TRAY™
(SCREW HOLDER)
MAG TRAY™ MODEL HP1202M
See Figure 12.
For convenience, your drill has a Mag Tray™ to place small
parts when doing a variety of tasks.
Fig. 12
Page 11
OPERATION
CHUCK REMOVAL
See Figures 13, 14, and 15.
MALLET
Lock the switch trigger by placing the direction of rotation
selector in center position. See Figure 3.
■
Insert a 5/16 inch or larger hex key into the chuck of
your drill and tighten the chuck jaws securely.
■
CHUCK JAWS
Tap the hex key sharply with a mallet in a clockwise
direction. See Figure 13. This will loosen the screw in
the chuck for easy removal.
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
5
■
KEYLESS CHUCK
10
■
Figure 14.
■
Note: The screw has left hand threads.
Insert hex key in chuck and tighten chuck jaws securely.
Tap sharply with a mallet in a counterclockwise direction.
This will loosen chuck on the spindle. It can now be
unscrewed by hand. See Figure 15.
HEX KEY
TO RETIGHTEN A LOOSE CHUCK
■
■
5
Fig. 14
5
■
■
Lock the switch trigger by placing the direction of rotation
selector in center position. See Figure 3.
Open the chuck jaws.
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key sharply with a mallet in a clockwise
direction. This will tighten chuck on the spindle.
Open the chuck jaws and remove hex key.
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
10
■
Fig. 13
10
The chuck may become loose on spindle and develop a
wobble. To tighten, follow these steps:
Fig. 15
Page 12
MAINTENANCE
DO NOT ABUSE POWER TOOLS. Abusive practices can
damage the tool, as well as the work piece.
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause
product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
a clean cloth to remove dirt, oil, grease, etc.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
CAUTION:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastics.
Any repairs requiring disassembly should only be
performed by a Ryobi Authorized Service Center. For
the repair center nearest you, call 1-800-525-2579.
BATTERIES
Your drill is equipped with Nickel-Cadmium rechargeable
batteries. Length of service from each charging will depend
on the type of work you are doing.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. See Page 6 for DISPOSAL OF
EXHAUSTED BATTERY. Do not disassemble the battery
pack.
To obtain the longest possible battery life, we suggest the
following:
■
■
■
Page 13
Store and charge your batteries in a cool area.
Temperatures above or below normal room temperature
wil shorten battery life.
Never store batteries in a discharged condition. Wait for
battery to cool and charge immediately.
All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your tool for long periods of time without using it,
recharge the batteries every month or two. This practice
will prolong battery life.
OPERATOR'S MANUAL
CORDLESS DRILL-DRIVER
MODEL NOS. HP962 / HP1202M
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
Authorized Service Center. You can also check our web site at www.ryobitools.com for a
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
•
MODEL NUMBERS HP962 / HP1202M
•
SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson SC 29625
Post Office Box 1207
Anderson SC 29622
Phone 1-800-525-2579
www.ryobitools.com
972000-873