-
HONDA
INSTALLATION
INSTRUCTIONS
Accessory
Application
LED TRUNK LIGHT
GL1800/D/DA
GL1800B/BD
Publication No.
MII 16426
P/N 08U74-MKC-A00
Issue Date
January 2018
Honda Dealer: Please give a copy of these instructions to your customer.
PARTS LIST
TOOLS AND SUPPLIES REQUIRED
(6)
Phillips screwdriver
Snips
Ruler
File
Scissors
Isopropyl alcohol
Shop towel
Torque wrench
(3)
(1)
©-
(4)
e-
(5)
TORQUE CHART
Tighten all screws, bolts, and nuts to their specified
torque values. Refer to the Service Manual for the torque
values of the removed parts.
(2)
Item
5 mm screw
No.
Description
Qty
(1)
Trunk inner lamp
1
(2)
Cushion
1
(3)
5 mm screw
2
(4)
Washer
2
(5)
Collar
2
(6)
Installation Instructions URL
1
N·m
4.2
kgf·m
Ibf·ft
0.5
3.8
I I I
INSTALLATION
NOTE:
Heat the bonding surfaces with a hair dryer if the
ambient air temperature is below 70°F (21°C).
The adhesive reaches full strength in 72 hours. Wait
at least 24 hours before riding your motorcycle.
Disconnect the negative (-) cable from the battery
before installing this accessory.
The clock memor y will be erased when you
disconnect the battery. Reset after reconnecting the
battery.
Reinstall the removed parts on the motorcycle and
make sure that the wires and harnesses are not
pinched.
TRUNK SUB HARNESS
Sold separately
(2)
(1)
(3)
(4)
For the installation, refer to the Installation
Instructions of accessory.
No.
Description
Qty
(1)
Trunk sub harness
1
(2)
Installation Instructions URL
1
(3)
Wire tie
1
(4)
Cushion
2
© 2018 American Honda Motor Co., Inc. - All Rights Reserved.
1 of 4
87945-MKC-A000.indd
1.
2.
5.
Perform step 1 to 18 on the trunk sub harness (sold
separately) installation instructions.
Cut out the
parts of inner trunk lid as shown.
After cutting, remove any burrs.
Clean the surface of the area shown using isopropyl
alcohol.
INNER TRUNK LID
ISOPROPYL ALCOHOL
SNIPS
After cutting, finish
with a round file.
INNER TRUNK LID
3.
Install the trunk inner lamp as shown.
5 mm SCREW
WASHER
6.
Connect the trunk inner lamp harness as shown.
TRUNK SUB HARNESS
COLLAR
2-PIN CONNECTOR (Blue)
After connecting, store the
connector in the harness boot.
TRUNK
INNER LAMP
INNER
TRUNK LID
TRUNK INNER
LAMP HARNESS
7.
Cut the cushion to the dimensions shown.
CUSHION
INNER TRUNK LID
4.
Perform step 19 to 22 on the trunk sub harness (sold
separately) installation instructions.
70 mm
SCISSORS
2 of 4
8.
Attach the cushions as shown.
TRUNK INNER LAMP HARNESS
9.
Install the inner trunk lid to the trunk lid as shown.
SCREW (Reuse)
CUT CUSHION
Remove the
adhesive backing
before attaching.
INNER TRUNK LID
INNER TRUNK LID
"
@·
/
1?'
)0'
P&l,r~
~~~/
~
0,
0
0
TRUNK LID
( Install the trunk lid with care not to damage the
part.
TRUNK LID
'-------
3 of 4
10. Install the striker rods as shown.
SCREW (Reuse)
STRIKER ROD
(Reuse)
REAR TRUNK LID
..
SCREW
SIDE
STRIKER ROD
11. Perform step 23 to 29 on the trunk sub harness (sold
separately) installation instructions.
4 of 4
">