CommScope TC-96275-IP Single Fiber Splice Cassette User Guide
PDF
Download
Document
Advertisement
Advertisement
10 Route fibers into base (a) Position spool to prepare for routing. (b) Route pigtail and feeder fibers counterclockwise starting along the outer walls and working towards the center of the cassette. (c) Line up the pegs on the cassette base with the mounting holes on the spool to finish routing. (d) Insert spool into base and ensure all fibers are under retaining fingers. Quick TC-96372-IP · Rev B · September, 2023 Start PROPEL PRODUCT PAGE QR CODE 8 Port Mass Fusion Splice Cassette for Propel Panel Tools and Materials Required TAPE MARKER SMALL SIDE CUTTER a FIBER SCISSORS b STRIPPER TAPE MEASURE FIBER FUSION SPLICER AND CLEAVER ISOPROPYL ALCOHOL c d 11 Apply Cover (a) Line the tabs on the cover with the slots near the front of the cassette base. (b) Lay the cover flat on the base and ensure all the tabs on the side of the cover and bases are lined up. With one hand holding the cassette base, push cover forward with other hand to engage tabs. Double check the rear tab is also engaged to prevent the cover from sliding off. 1 . INCLUDED: SPLICE PROTECTORS (40 mm LONG) and CABLE TIES (30 - 40 mm LONG) Prepare cable for mass fiber splice cassette installation. Refer to Table 1 for Feeder and Pigtail Lengths. “Feeder Initial Length” is the recommended length of fiber to bring into the cassette. “Feeder Cut Length” and “Pigtail Cut Length” is measured from the front of the cassette and is the recommended cut length for the initial splice. A maximum of (1) rework is allowed per splice. Table 1: Pigtail and Feeder Lengths a b Product Information http://www.commscope.com 8 Port Cassette, shown above Product Information http://www.commscope.com/ SupportCenter Page 4 of 4 29009-B 660106107 Rev B © 2023, CommScope, Inc. All Rights Reserved. Page 1 of 4 2 Remove cassette cover Using thumb & finger, disengage rear tab by lifting and pulling backward to remove the cover. . 3 Prepare to place feeder fiber in cassette 5 (a) Remove spool and splice holder from cassette, then remove and discard foam blocks. (b) Unspool and extend pigtail fiber beyond front of cassette. Measure and trim pigtail and feeder Extend feeder fibers beyond the front of the cassette base, then measure and trim pigtail and feeder to specified cut length per Table 1. Feeder foam block splice holder Pigtail foam block spool foam block a 6 Install splice protectors on all fibers to be spliced 7 Strip, clean, and splice fibers following recommended method. Use provided splice protectors. Splice protector length should be 45mm maximum. 6 Splice feeder and pigtail fibers b Splice Protectors 4 Install feeder fiber in splice cassette. 9 (a) Insert plastic sleeve into mesh sleeve and secure using tape. Insert feeder fiber into sleeve.(b) Secure feeder fiber using two cable ties. (c) Snip off ends of cable ties close to head. (d) Push the head downward until it is below the top of the cassette wall. Plastic Sleeve 8 a b c (a) Load splice protectors into splice holder (b) Utilizing the spool fiber retainers, route pigtail fibers counterclockwise until feeder and pigtail fibers converges. 6 Cable Ties Load splice protectors into splice holder Preparing to load splice protectors Locate “P” and “F” marking on spool. When loading splice protectors, ensure pigtail is exiting spool through the side with “P” marking and the feeder is exiting through the side with “F” marking. a d b Page 2 of 4 http://www.commscope.com 29010-B http://www.commscope.com Page 3 of 4 ">

Public link updated
The public link to your chat has been updated.
Advertisement