Titan GHT550T2 Pole Hedge Trimmer User Manual

EN
Original Instructions_MNL_TTB826HDC_V1_230831
Pole Hedge
Trimmer
550W 50cm
TTB826HDC
WARNING: Read the instructions before using the product!
EN
Let’s
get started...
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
02
Getting started...
02
Safety information
Your product
Before you start
03
12
13
In more detail...
17
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
Technical specifications
Declaration of conformity
18
21
24
28
28
29
31
33
TTB826HDC by TITAN
Safety information
EN
Safety warnings
WA R N I N G ! R e a d a l l s a f e t y w a r n i n g s ,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
3. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Getting started...
General power tool safety warnings
03
EN
Safety information
TTB826HDC by TITAN
Getting started...
Safety warnings
04
3. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
2. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
3. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
Safety information
power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
7. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
Power tool use and care
1. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
4. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
EN
Getting started...
TTB826HDC by TITAN
05
EN
Safety information
TTB826HDC by TITAN
Getting started...
Safety warnings
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
5. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
8. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Service
1. Have your power tools serviced by a qualified repair
person using only identical replacement parts. This
will ensure that safety of the power tool is maintained.
06
Hedge trimmer safety warnings:
1. Keep all parts of the body away from the blade. Do
not remove cut material or hold material to be cut
when blades are moving. Blades continue to move
after the switch is turned off. A moment of inattention
while operating the hedge trimmer may result in serious
personal injury.
Safety information
2. Carry the hedge trimmer by the handle with the
blade stopped and taking care not to operate any
power switch. Proper carrying of the hedge trimmer will
decrease the risk of inadvertent starting and resultant
personal injury from the blades.
3. When transporting or storing the hedge trimmer,
always fit the blade cover. Proper handling of the
hedge trimmer will decrease the risk of personal injury
from the blades.
4. When clearing jammed material or servicing the
unit, make sure all power switches are off and the
power cord is disconnected. Unexpected actuation
of the hedge trimmer while clearing jammed material or
servicing may result in serious personal injury.
5. Hold the hedge trimmer by insulated gripping
surfaces only, because the blade may contact hidden
wiring or its own cord. Blades contacting a "live" wire
may make exposed metal parts of the hedge trimmer
"live" and could give the operator an electric shock.
6. Keep all power cords and cables away from cutting
area. Power cords or cables may be hidden in hedges
or bushes and can be accidentally cut by the blade.
7. Do not use the hedge trimmer in bad weather
conditions, especially when there is a risk of lightning.
This decreases the risk of being struck by lightning.
EN
Getting started...
TTB826HDC by TITAN
Additional safety warnings for pole hedge trimmer
1. To reduce the risk of electrocution, never use the
pole hedge trimmer near any electrical power lines.
Contact with or use near power lines may cause serious
injury or electric shock resulting in death.
2. Always use two hands when operating the pole
hedge trimmer. Hold the pole hedge trimmer with both
hands to avoid loss of control.
3. Always use head protection when operating the pole
07
EN
Safety information
TTB826HDC by TITAN
Getting started...
Safety warnings
08
hedge trimmer overhead. Falling debris can result in
serious personal injury.
4. Before operating the hedge trimmer, the user should
make sure the locking device(s) of any moving
elements (e.g. the extended shaft and pivoting
element), if any, are in the locked position.
Vibration and noise reduction
To reduce the impact of noise and vibration emission,
limit the time of operation, use low-vibration and lownoise operating modes as well as wear personal
protective equipment.
Take the following points into account to minimise the
vibration and noise exposure risks:
1. Only use the product as intended by its design and these
instructions.
2. Ensure that the product is in good condition and well
maintained.
3. Use correct attachments for the product and ensure they
are in good condition.
4. Keep tight grip on the handles/grip surface.
5. Maintain this product in accordance with these instructions
and keep it well lubricated (where appropriate).
6. Plan your work schedule to spread any high vibration tool
use across a longer period of time.
7. Prolonged use of the product exposes the user to
vibrations that can cause a range of conditions collectively
known as hand-arm vibration syndrome (HAVS) e.g.
fingers going white; as well as specific diseases such as
carpal tunnel syndrome. To reduce this risk when using
the product, always wear protective gloves and keep your
hands warm.
TTB826HDC by TITAN
Safety information
EN
Familiarise yourself with the use of this product by
means of this instruction manual. Memorise the safety
directions and follow them to the letter. This will help to
prevent risks and hazards.
1. Always be alert when using this product, so that you
can recognise and handle risks early. Fast intervention
can prevent serious injury and damage to property.
2. Switch the product off and disconnect from the
power supply if there are malfunctions. Have the
product checked by a qualified professional and repaired,
if necessary, before you operate it again.
Residual risks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of injury
and damage remain. The following dangers can arise
in connection with the structure and design of this
product:
1. Health defects resulting from vibration emission if the
product is being used over long periods of time or not
adequately managed and properly maintained.
2. Injuries and damage to property due to broken
attachments or the sudden impact of hidden objects
during use.
3. Danger of injury and property damage caused by
flying objects.
WA R N I N G ! T h i s p r o d u c t p r o d u c e s a n
electromagnetic field during operation! This field
may under some circumstances interfere with
active or passive medical implants! To reduce
the risk of serious or fatal injury, we recommend
persons with medical implants to consult their
doctor and the medical implant manufacturer
before operating this product!
Getting started...
Emergency
09
EN
TTB826HDC by TITAN
Safety information
Getting started...
Symbols
On the product, the rating label and within these instructions you will find among
others the following symbols and abbreviations. Familiarise yourself with them
to reduce hazards like personal injuries and damage to property.
V~
Volt, (alternating voltage) Hz
/min or
Per minute
W
min-1
g cm
Centimeter
kg mm
Millimetre
m
dB(A)
Decibel (A-rated)
m/s² Lock / to tighten or secure. Read the instruction
manual.
xxWyy
Hertz
Watt
Gram
Kilogram
Metre
Metres per second squared
Unlock / to loosen.
Note / Remark.
Caution / Warning.
Manufacturing date code; year of manufacturing (20xx) and week of
manufacturing (Wyy)
Wear hearing protection. Wear eye protection.
Wear a dust mask. Wear protective gloves.
Wear protective, slip-resistant footwear.
Wear tight-fitted protective clothes.
Wear head protection, where there is a risk of falling objects.
Switch the product off and disconnect it from the power supply
before assembly, cleaning, adjustments, maintenance, storage and
transportation.
Do not expose the product to rain or wet conditions (moisture).
Keep hands away from moving cutting device!
10
TTB826HDC by TITAN
Safety information
EN
Objects thrown by the product could hit the user or other bystanders.
Always ensure that other people and pets remain at a safe distance
from the product when it is in operation. In general, children must not
come near the area where the product is.
Disconnect the product from the mains plug if the cord is damaged or
entangled. DON’T TOUCH THE CORD BEFORE DISCONNECTING
THE SUPPLY.
105
Guaranteed sound power level value in 105 dB.
The product is of Protection class II. That means it is equipped with
enhanced or double insulation.
The product complies with the applicable European directives and an
evaluation method of conformity for these directives was done.
Getting started...
Keep sufficient distance away from electrical power lines.
UK Conformity Assessed.
WEEE symbol. Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check
with your Local Authority or local store for recycling advice.
11
EN
TTB826HDC by TITAN
Your product
Getting started...
Your product
9 10
3 4 5
2
1a
1
6
7
11 12 13
14
16 15
8
2a
17b
17
17a
18
1. Cutting device (blade)
a. Blade tip protector
2. Motor head
a. Air vents
3. Unlock button for angle adjustment
4. Pole support
a. Bore (x2)*
5. Locking sleeve
6. Pole extension
a. Lock pin (x2)*
7. Locking lever for length adjustment
8. Front pole
9. Soft grip
10. Loop
11.Lock-off button
12. Rear handle
13.Power cord with plug
14. Rear safeguard
15. Cord retainer
16.On/off switch
17. Harness
a. Securing clip
b. Quick release
18. Blade cover
NOTE: Parts marked with * are not shown in this overview. Please
refer to the respective part in the instruction manual.
12
TTB826HDC by TITAN
Before you start
EN
1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices if applicable.
3. Make sure the delivery contents are complete and free of any damage. If
you find that parts are missing or show damage do not use the product but
contact your dealer. Using an incomplete or damaged product represents a
hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and
operation. This also includes suitable personal protective equipment.
WARNING! The product and the packaging are not children’s toys!
Children must not play with plastic bags, sheets and small parts!
There is a danger of choking and suffocation!
You will need
(items not supplied)
Suitable personal protective equipment
Suitable extension cord for outdoor use
Lubricant for blade
(items supplied)
Harness (17)
Blade cover (18)
Getting started...
Unpacking
NOTE: The accessories required depend on the intended application.
Ask your dealer for advice.
Setup
WARNING! The product must be fully assembled before operation!
Do not use a product that is only partly assembled or assembled with
damaged parts!
Follow the assembly instructions step-by-step and use the pictures
provided as a visual guide to easily assemble the product!
Before using the product, familiarise yourself with the operating
features read the entire instruction manual paying particular attention
to the safety rules and operating procedures.
Do not connect the product to power supply before removing the
blade cover (11).
13
EN
TTB826HDC by TITAN
Before you start
Setup
Getting started...
Pole assembly
1. Loosen the locking lever (7) (Fig. 1, step 1) and pull out the pole extension (6)
(Fig. 1, step 2), then fasten the locking lever (7) (Fig. 1, step 3).
2. Move the locking sleeve (5) back onto the pole extension (Fig. 1, step 4).
3. Align the pole extension (6) with the pole support (4) and insert it. Make sure
the pins (6a) snaps in the bores (4a) for reliable connection (Fig. 1, step 5).
4. Fit the locking sleeve (5) on the thread of pole support (4) and tighten the
locking sleeve (5) clockwise to secure the connections (Fig. 1, step 6).
4.
6
5
2.
1.
6a
7 3.
4
6
6.
5.
4a
6a
5
Fig. 1
Blade cover
1. Remove the blade cover (18) from the cutting device (blade) (1) before
operation (Fig. 2).
2. Keep the blade cover (18) safely.
1
18
Fig. 2
NOTE: Always attach the blade cover (18) when the product is not in
use, for storage and transportation.
To attach the blade cover (18), align and push the blade cover onto the
cutting device (blade) (1).
14
Before you start
TTB826HDC by TITAN
EN
For safety reasons the product is equipped with a short power cord (13). Do not
connect the product directly to the power supply using this power cord. A proper
extension cord is required for operation. Observe the technical requirements for
this product when purchasing an extension cord.
NOTE: For your safety, it is required that the plug attached to this
product is always connected to an extension cord! The extension cord
must be suitable for outdoor use with sockets protected against water
splashing! Ensure the extension cord is of the proper size and type for
your product (≥ 1.0 mm²)!
Always use a residual current supply (RCD) protected supply.
1. Double the extension cord back, about 30 cm from the end and lead the loop
through the hole of the rear safeguard (14) (Fig. 3, step 1).
2. Pull it over the cord retainer (15) and gently tug on the cord to ensure that it is
firmly secured (Fig. 3, step 2).
14
Getting started...
Connection to power supply
14
15
1.
2.
Fig.3
15
EN
TTB826HDC by TITAN
Before you start
2.
1.
Connection to power
supply
Getting started...
3. Connect the power cord (13) to the socket of the extension cord (Fig. 4).
13
16
Fig.4
4. Make sure the on/off switch (16) is not squeezed.
5. Connect the plug of extension cord into a suitable socket.
WARNING! Check the voltage! The voltage must comply with the
information on the rating label!
If using an extension cord it must be suitable for outdoor use with
sockets protected against water splashing.
Ensure the extension cord is of the proper size and type for your
product:
· 1.5 mm2 for up to 60 m
· 2.5 mm2 for up to 100 m
6. Your product is now ready to be used.
16
EN
TTB826HDC by TITAN
Product functions
18
Operation
21
Care and maintenance
24
Troubleshooting
28
Recycling and disposal
28
Guarantee
29
Technical specifications
31
Declaration of conformity
33
In more detail...
In more
detail...
17
EN
TTB826HDC by TITAN
Product functions
Intended use
In more detail...
This electric hedge trimmer TTB826HDC is designated with a rated power input
of 550 Watts.
The product is intended for cutting and trimming of hedges, bushes and shrubs
in domestic gardens. The maximum cutting capacity must be observed. Do not
cut branches exceeding the stated maximum capacity.
The use of this product in case of rain or humid environment is prohibited.
For safety reasons it is essential to read the entire instruction manual before
first operation and to observe all the instructions therein.
This product is intended for private domestic use only, not for any commercial
trade use. It must not be used for any purposes other than those described.
Harness
The harness (17) helps the operator to carry the product.
1. Place the harness (17) so that it runs over the left
shoulder, crossing the chest and back. The securing
clip (17a) must be located at the right hip.
The quick release (17b) must be in front (Fig. 5).
2. Adjust the length of the harness (17) so that the
securing clip (17a) is approximately 15 cm below
your waist.
3. Attach the securing clip (17a) to the loop (10) (Fig. 6).
4. Lock the harness (17) onto the loop (10) by the
securing clip (17a) (Fig. 7).
17 17
17b17b
17a 17a
Fig. Fig.
5 5
17a 17a
17 17
17a 17a
10 10
Fig.
Fig. 6 6
18
10 10
Fig.
Fig. 7 7
TTB826HDC by TITAN
Product functions
EN
Harness
WARNING! Always attach the product to the harness (17). Do not
carry it only with your hands!
5. In case of emergency hold the soft grip (9) of the front
pole (8) with the left hand, and use the right hand to
press two clips of the quick release (17b). The product
together with the securing clip (17a) will be released
automatically from the body because of the weight of
the product (Fig. 8).
1717
17b
17b
Fig.
88
Fig.
Length adjustment
1. Loosen the locking lever (7) (Fig. 9, step 1).
2. Adjust to the required length by pulling out or pushing in the pole extension (6)
(Fig. 9, step 2).
WARNING! The length of the extension pole is limited! Stop pushing/
pulling as soon as you feel a resistance!
Extend the extension only to the length required to reach the hedges
being trimmed! Do not attempt to use the product at a length which
does not allow you to achieve proper footing and balance at all times!
In more detail...
17a
17a
3. Secure the position of pole extension (6) by fastening the locking lever (7)
back to its original position (Fig. 9, step 3).
2. 2.
6 6 1. 1.
Fig.
99
Fig.
77
3. 3.
19
EN
Product functions
TTB826HDC by TITAN
In more detail...
Angle adjustment
The angle of the blade head can be adjusted into five 30°
30°
33 44
positions (Fig. 10):
1. Press the unlock button (3) to unlock the
0°
angleNadjustment and hold it in position.
0°
2. Adjust the blade head to the desired position by
swing the pole support (4).
3. Release the unlock button (3) and keep moving
-30°
-30°
the pole support (4) until it locks in place.
4. Ensure the unlock button (3) snaps in place before
-60°
-60°
-90°
-90°
operation.
Fig.
10
Fig. 10
WARNING! The blade head can be adjusted in five different positions.
Always ensure the blade head is securely locked! Do not attempt to
use the product with the head in an intermediate position!
Switching on/off
1. Ensure the cutting device (blade) (1) does not touch any objects. Remove
the blade cover (18) from the cutting device (blade) (1) before switching the
product on.
2. Hold the product with one hand on the soft grip (9) of the front pole (8) and the
other hand on the rear handle (12).
3. Pull back the lock-off button (11) and hold it in position (Fig. 11, step 1).
4. Squeeze the on/off switch (16) to switch the product on (Fig. 11, step 2).
Release the lock-off button (11) afterwards.
5. Release the on/off switch (16) to switch the product off.
1.
11 1.
11
2.2.
20
12
12
16
16
Fig.11
11
Fig.
Operation
TTB826HDC by TITAN
EN
1. Check the product, its power cord and plug as well as accessories for damage
before each use. Do not use the product if it is damaged or shows wear.
2. Double check that the accessories and attachments are properly fixed.
3. Always hold the product on its handles. Keep the handles dry to ensure safe
support.
4. Ensure that the air vents are always unobstructed and clear. Clean them if
necessary with a soft brush. Blocked air vents may lead to overheating and
damage the product.
5. Switch the product off immediately if you are disturbed while working by other
people entering the working area. Always let the product come to complete
stop before putting it down.
6. Do not overwork yourself. Take regular breaks to ensure you can concentrate
on the work and have full control over the product.
WARNING! Ensure the power cord or the extension cord will not
touch the cutting device (blade) (1) during operating!
Danger of electric shock!
Trimming times
green leaf hedges
evergreens
conifers and other fast growing shrubs
June to October
April and August
every 6 - 8 weeks
In more detail...
General operation
Trimming
NOTE: Try to keep the cutting device angled at approximately 15° to
the cutting surface.
1. Make sure that the blade cover (18) is removed.
2. Ensure that no people or animals are in the work area.
3. Adjust the product to a suitable pole length and blade head angle.
4. Carry the product with the harness (17).
21
EN
TTB826HDC by TITAN
Operation
Trimming
In more detail...
5. Cut and remove branches exceeding the cutting capacity of this product using
a proper pruner before operation.
6. Always hold the product firmly with both hands on soft grip (9) of the front pole
(8) and the rear handle (12). Never operate this product using only one hand.
7. Do not rush and do not attempt to cut too much with one stroke of the cutting device.
8. First cutting both sides from the bottom upwards to the top. This will prevent
any of the cuttings falling into the path of the area still to be cut (Fig. 12).
9. After cutting the sides proceed to the top. Try to keep the cutting device
angled at approximately 15° to the cutting surface (Fig. 13).
22
0-15˚
0-15˚
Fig.
1212
Fig.
Fig. 12
0-15˚
Fig.
1313
Fig.
Fig. 13
10. When cutting wide hedges with the cutting area
in sight move the cutting blade lightly through the
cutting surface in a sweeping motion following the
shape of the hedge or shrub. A slight tilt downwards
of the cutting blade in the direction of motion is
recommended for optimum cutting performance.
11. Cut in a number of stages to achieve a better result
rather than trying to cut in one go if the area being
cut is particularly long (Fig. 14); smaller cuttings will
Fig.
1414
allow for easy composting.
Fig.
Fig. 14
12. Move the product with slow motion forward when
cutting higher hedge and the cutting area out of sight (Fig. 15).
Fig.
1515
Fig.
Fig. 15
TTB826HDC by TITAN
Operation
EN
Fig. 16
13. Lubricate the internal surfaces of the blade if the cutting device (blade) (1)
overheats during operation (Fig. 17).
WARNING! This operation must only be performed when the blades
have stopped running and the product is switched off!
In more detail...
NOTE: When shaping it is advisable to achieve a trapezoidal shape
(Fig. 16). A trapezoidal cut corresponds to the natural growth of plants
and results in optimal hedge growth, as it will expose more light to the
lower end of the hedge.
1
Fig. 17
After use
1. Switch the product off, disconnect the product from the power supply and let it
cool down.
2. Attach the blade cover (18) if necessary.
3. Check, clean and store the product as described below.
23
EN
Care and maintenance
TTB826HDC by TITAN
The golden rules for care
In more detail...
WARNING! Always switch the product off, disconnect the plug from
the power supply. Let the product cool down before performing
inspection, maintenance and cleaning work!
1. Keep the product clean. Remove debris from it after each use and before
storage.
2. Regular and proper cleaning will help ensure safe use and prolong the life of
the product.
3. Inspect the product before each use for worn and damaged parts. Do not
operate it if you find broken and worn parts.
WARNING! Only perform repairs and maintenance work according to
these instructions! All further works must be performed by a qualified
specialist!
General Cleaning
1. Clean the product with a damp cloth and pH-neutral soap. Use a brush for
areas that are hard to reach.
2. In particular clean the air vents (2a) after every use with a cloth and brush.
3. Remove stubborn dust with high pressure air (max. 3 bar).
NOTE: Do not use chemical, alkaline, abrasive or other aggressive
detergents or disinfectants to clean this product as they might be
harmful to its surfaces.
4. Check for worn or damaged parts. Replace worn parts as necessary or
contact an authorised service centre for repair before using the product
again. Check for worn or damaged parts. Replace worn parts as necessary or
contact an authorised service centre for repair before using the product again.
24
TTB826HDC by TITAN
Care and maintenance
EN
Cutting device (blade)
WARNING! Wear safety gloves when working on the cutting device
and close to it! Use appropriate tools to remove debris, e. g. a brush
or wooden stick! Never use your bare hands!
Power cord
If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a safety hazard.
In more detail...
1. Keep the cutting device (blade) (1) clean and free of debris. Remove
trimmings with a brush.
2. Apply a small amount of suitable lubricant on the cutting device (blade) to
retain a good cutting performance (Fig. 17).
25
EN
Care and maintenance
TTB826HDC by TITAN
UK plug (only for UK market)
In more detail...
If you need to replace the fitted plug, then follow the instructions below.
IMPORTANT: The wires in the mains lead are coloured in accordance with the
following code:
Blue – Neutral
Brown – Live
As the colours of the wire in the mains lead of this product may not correspond
with the coloured marking identifying the terminals in your plug, proceed as
follows. The wire, which is coloured blue, must be connected to the terminal,
which is marked with N or coloured black. The wire, which is coloured brown,
must be connected to the terminal, which is marked L or coloured red.
Connect
Blue to
N(Neutral)
13 AMP fuse
approved to
BS 1362
Brown L(Live)
Outer sleeve
Cable grip
WARNING! Never connect live or neutral wires to the earth terminal
of the plug, which is marked with E.
Only fit an approved 13 Amp BS 1363 or BS 1363/A plug and the correctly rated
fuse.
If in doubt, consult a qualified electrician.
NOTE: If a moulded plug is fitted and has to be removed take great
care in disposing of the plug and severed cable, it must be destroyed
to prevent engaging into a socket.
26
TTB826HDC by TITAN
Care and maintenance
EN
Repair
This product does not contain any parts that can be repaired by the consumer.
Contact an authorised service centre or a similarly qualified person to have it
checked and repaired.
1. Switch the product off and disconnect it from the power supply.
2. Clean the product as described above.
3. Attach the blade cover (18) onto the cutting device (blade) (1).
4. Dismantle the pole assembly if necessary.
5. Store the product and its accessories in a dark, dry, frost-free, well-ventilated
place.
6. Always store the product in a place that is inaccessible to children. The ideal
storage temperature is between 10 °C and 30 °C.
7. We recommend using the original package for storage or covering the product
with a suitable cloth or enclosure to protect it against dust.
Transportation
1. Switch the product off and disconnect it from the power supply
2. Attach the blade cover (18) onto the cutting device (blade) (1).
3. Always carry the product by its soft grip (9) of the front pole (8) and rear
handle (12).
4. Protect the product from any heavy impact or strong vibrations which may
occur during transportation in vehicles.
5. Secure the product to prevent it from slipping or falling over.
In more detail...
Storage
27
EN
Troubleshooting / Recycling and disposal
TTB826HDC by TITAN
Troubleshooting
Suspected malfunctions are often due to causes that the users can fix
themselves. Therefore check the product using this section. In most cases the
problem can be solved quickly.
In more detail...
WARNING! Only perform the steps described within these instructions!
All further inspection, maintenance and repair work must be performed
by an authorised service centre or a similarly qualified specialist if you
cannot solve the problem yourself!
Problem
Possible cause
Solution
1. Product does 1.1. Not connected to
1.1. Connect to power
not start
power supply
supply
1.2. Power cord or plug is 1.2. Check by a specialist
defective
electrician
1.3. Other electrical defect 1.3. Check by a specialist
to the product
electrician
2. Product does 2.1. Extension cord not
2.1. Use a proper
not reach full
suitable for operation
extension cord
power
with this product
2.2. Power source
2.2. Connect to another
(e.g. generator) has
power source
too low voltage
2.3. Air vents are blocked 2.3. Clean the air vents
3. Unsatisfactory 3.1. Blade is worn /
3.1. Replace with a new one
result
damaged
3.2. Thickness of branches 3.2. Only cut branches
exceeds capacity
complying with the capacity
4. Excessive
4.1. Blade is dull /
4.1. Replace with a new one
vibration or
damaged
noise
4.2. Bolts/nuts are loose
4.2. Tighten bolts/nuts
Recycling and disposal
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or local store for recycling advice.
28
For further information visit www.recycle-more.co.uk.
The product comes in a package that protects it against damage during shipping.
Keep the package until you are sure that all parts have been delivered and the
product is working properly. Recycle the package afterwards.
TTB826HDC by TITAN
Guarantee
EN
Guarantee
To make a claim under this guarantee, you must present your proof of purchase
(such as a sales receipt, purchase invoice or other evidence admissible under
applicable law), please keep your proof of purchase in a safe place. For this
guarantee to apply, the product you purchased must be new, it will not apply to
second hand or display products. Unless stated otherwise by applicable law, any
replacement product issued under this guarantee will only be guaranteed until
expiry of the original period guarantee period.
This guarantee covers product failures and malfunctions provided the product
was used for the purpose for which it is intended and subject to installation,
cleaning, care and maintenance in accordance with the information contained in
these terms and conditions, in the user manual and standard practice, provided
that standard practice does not conflict with the user manual.
This guarantee does not cover defects and damage caused by normal wear
and tear or damage that could be the result of improper use, faulty installation or
assembly, neglect, accident, misuse, or modification of the product. Unless stated
otherwise by applicable law, this guarantee will not cover, in any case, ancillary
costs (shipping, movement, costs of uninstalling and reinstalling, labour etc), or
direct and indirect damage.
In more detail...
We take special care to select high quality materials and use manufacturing
techniques that allow us to create products incorporating design and durability.
This product has a manufacturer’s guarantee of 2 years against manufacturing
defects, from the date of purchase (if bought in store) or date of delivery (if
bought online), at no additional cost for normal (non-professional or commercial)
household use.
Rights under this guarantee are enforceable in the country in which you
purchased this product. Guarantee related queries should be addressed to the
store you purchased this product from.
The guarantee is in addition to and does not affect your statutory rights.
Manufacturer:
Kingfisher International Products Limited
3 Sheldon Square, W26PX London United Kingdom
www.kingfisher.com/products
29
EN
Guarantee
TTB826HDC by TITAN
Guarantee
Distributor:
B&Q plc
Chandlers Ford, Hants, SO53 3LE, United Kingdom
www.diy.com
In more detail...
Screwfix Direct Limited
Trade House, Mead Avenue, Yeovil, BA22 8RT, United Kingdom
www.screwfix.com
30
TTB826HDC by TITAN
Technical specifications
EN
General
>Rated voltage, frequency
>Rated power input
>Rated no load speed n0
>Blade length
>Max. cutting length
>Tooth spacing
>Max. cutting diameter
>Protection class
>Weight
>Length of power cord
>Dimensions
Sound values
>Sound pressure level at operator’s
position LpA
>Uncertainty KpA
>Measured sound power level LWA
>Uncertainty KWA
Hand arm vibration values
>Front handle ah,W
>Rear handle ah,W
>Uncertainty K
: 230-240 V~,50 Hz
: 550 W
: 3800 min-1
: 50 cm
: 47 cm
: 28 mm
: Max. 22 mm
: II /
: approx. 3.8 kg
: approx. 25 cm
: approx. 174*100*2580 mm
: 91.29 dB(A)
: 3 dB(A)
: 99.29 dB(A)
: 6.19 dB(A)
: 1.538 m/s²
: 2.107 m/s²
: 1.5 m/s2
The sound values have been determined according to noise test code given in
EN 62841-4-2, using the basic standards EN ISO 11201 and EN ISO 3744.
The sound intensity level for the operator may exceed 80 dB(A) and ear
protection measures are necessary.
The declared vibration value has been measured in accordance with a standard
test method (according to EN 62841-4-2) and may be used for comparing
one product with another. The declared vibration value may also be used in a
preliminary assessment of exposure.
WARNING! The vibration and noise emissions during actual use
of the power tool can differ from the declared values depending on
the ways in which the tool is used especially what kind of workpiece
is processed; and need to identify safety measures to protect the
operator that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the operating cycle
such as the times when the tool is switched off and when it is running
idle in addition to the trigger time).
In more detail...
Technical specifications
31
EN
Technical specifications
Rating label explanation
In more detail...
Pole Hedge Trimmer: TTB826HDC
TTB=TITAN (brand)
826=Series number
HDC=Pole hedge trimmer
32
TTB826HDC by TITAN
TTB826HDC by TITAN
Declaration of conformity
EN
Declaration of conformity
(EN) EU DECLARATION OF CONFORMITY
(FR) DÉCLARATION UE DE CONFORMITÉ
(PL) DEKLARACJA ZGODNOŚCI UE
(RO) DECLARAȚIA DE CONFORMITATE UE
(ES) DECLARACIÓN UE DE CONFORMIDAD
(PT) DECLARAÇÃO DE CONFORMIDADE UE
Product/ Produit/ Produkt/Produsul/Producto/Produto


Pole Hedge Trimmer 550W 50cm/ Taille-haie électrique sur perche 550W 50cm/ Teleskopowe nożyce do żywopłotu
550W 50cm/ Unealtă de tuns gard viu cu braț telescopic 550W 50cm/ Cortasetos de altura 550W 50cm / Corta-sebes
e podador 550W 50cm
TTB826HDC
Serial number: from 000001 to 999999
Name and address of the manufacturer or his authorised representative:
Nom et adresse du fabricant ou de son mandataire:
Nazwa i adres producenta lub jego upoważnionego przedstawiciela:
Denumirea și adresa producătorului sau a reprezentantului său autorizat:
Nombre y dirección del fabricante o de su representante autorizado:
Nome e endereço do fabricante ou do respetivo mandatário:
Kingfisher International Products B.V.,
Rapenburgerstraat 175E,
1011 VM Amsterdam,
The Netherlands
This declaration of conformity is issued under the sole responsibility of the manufacturer.
La présente déclaration de conformité est établie sous la seule responsabilité du fabricant.
Niniejsza deklaracja zgodności wydana zostaje na wyłączną odpowiedzialność producenta.
Prezenta declarație de conformitate este emisă pe răspunderea exclusivă a producătorului.
La presente declaración de conformidad se expide bajo la exclusiva responsabilidad del fabricante.
A presente declaração de conformidade é emitida sob a exclusiva responsabilidade do fabricante.
Object of the declaration/Objet de la declaration/Przedmiot deklaracji/Obiectul declarației/Objeto de la declaración/Objeto da declaração
Product/Produit/Produkt/Produsul/Producto/ Produto
Model/Modèle/Model/Modelul/Modelo/
EAN
Modelo
Pole Hedge Trimmer 550W 50cm/ Taille-haie
électrique sur perche 550W 50cm/ Teleskopowe
nożyce do żywopłotu 550W 50cm/ Unealtă de tuns
gard viu cu braț telescopic 550W 50cm/ Cortasetos
de altura 550W 50cm / Corta-sebes e podador
550W 50cm
TTB826HDC
5059340880785 (UK)
5059340240183 (EU)
The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:
L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable:
Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego:
Obiectul declarației descris mai sus este în conformitate cu legislația relevantă de armonizare a Uniunii:
El objeto de la declaración descrita anteriormente es conforme con la legislación de armonización pertinente de la Unión:
O objeto da declaração acima descrito está em conformidade com a legislação de harmonização da União aplicável:
2006/42/EC as amended Machinery Directive
2014/30/EU as amended Directive Electromagnetic compatibility
2000/14/EC as amended Outdoor Noise Directive
2011/65/EU as amended
Directive Restriction of the use of certain hazardous substances in electrical and electronic equipment
Directive 2006/42/CE relative aux machines
2014/30 / UE telle que modifiée Directive Compatibilité électromagnétique
Directive 2000/14/CE relative aux émissions sonores extérieures
Directive 2011/65/UE relative à la limitation de l’utilisation de certaines substances dangereuses dans les équipements électriques et
électroniques
2006/42/WE w zmienionej dyrektywie maszynowej
2014/30 / UE ze zmianami Dyrektywa Kompatybilność elektromagnetyczna
2000/14/WE w zmienionej dyrektywie w sprawie hałasu na zewnątrz
2011/65 / UE ze zmianami Dyrektywa Ograniczenie stosowania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i
elektronicznym
2006/42/CE, astfel a fost modificată Directiva privind echipamentele
2014/30/UE, astfel a fost modificată Directiva privind compatibilitatea electromagnetică
2000/14/CE, astfel a fost modificată Directiva privind zgomotul în aer liber
2011/65/UE, astfel a fost modificată Directiva privind limitarea utilizării anumitor substanțe periculoase în echipamentele electrice și
electronice
Directiva sobre maquinaria modificada 2006/42/CE
2014/30/UE modificada Directiva Compatibilidad electromagnética
2000/14/CE modificada Directiva sobre ruido al aire libre
2011/65/UE modificada Directiva Restricción del uso de determinadas sustancias peligrosas en equipos eléctricos y electrónicos
2006/42/CE como diretiva de máquinas alteradas
In more detail...

33
EN
Declaration of conformity
TTB826HDC by TITAN
Declaration of conformity
2014/30/UE como alteração da compatibilidade eletromagnétic
2000/14/CE como diretiva de ruído exterior alterada
2011/65/UE como restrição diretiva alterada da utilização de certas substâncias perigosas em equipamentos elétricos e eletrónicos
In more detail...
Measured Sound Power Level
Le niveau de puissance acoustique mesuré
Zmierzony poziom mocy akustycznej
Nivel de putere acustică măsurat
Nivel de potencia sonora medido
Nível de potência sonora medido
: 99.29 dB(A)
References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is
declared:
Références des normes harmonisées pertinentes appliquées, y compris la date de celles-ci, ou des autres specifications techniques, y
compris la date de celles-ci, par rapport auxquelles la conformité est déclarée:
Odwołania do odnośnych norm zharmonizowanych, które zastosowano, wraz z datą normy, lub do innych specyfikacji technicznych, wraz z
datą specyfikacji, w odniesieniu do których deklarowana jest zgodność:
Trimiteri la standardele armonizate relevante folosite, inclusiv data standardului, sau trimiteri la celelalte specificații tehnice, inclusiv data
specificațiilor, în legătură cu care se declară conformitatea:
Referencias a las normas armonizadas pertinentes utilizadas, incluidas las fechas de las normas, o referencias a las otras especificaciones
técnicas, incluidas las fechas de las especificaciones, respecto a las cuales se declara la conformidad:
Referências às normas harmonizadas aplicáveis utilizadas, incluindo a data da norma, ou às outras especificações técnicas, incluindo a data
da especificação, em relação às quais é declarada a conformidade:
EN 62841-1: 2015
EN 62841-4-2: 2019
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019 +A1
EN 61000-3-3:2013+A2
EN ISO 3744:1995
Authorised signatory and technical file holder/signataire et responsable de la documentation technique authorisé/ podmiot uprawniony do
wystawienia i adres prezechowywania dokumentacji technicznej/semnatar autorizat și deținător al dosarului tehnic/firmante autorizado y
titular del expediente tecnico/ signatário autorizado e detentor da ficha técnica
Kingfisher International Products B.V.,
Rapenburgerstraat 175E,
1011 VM Amsterdam,
The Netherlands
David Awe
Group Quality Director
34
Guaranteed Sound Power Level
Le niveau de puissance acoustique garant
Gwarantowany poziom mocy akustycznej
Nivel de putere acustică garantat
Nivel de potencia sonora garantizado
Nível de potência sonora garantido
: 105 dB(A)
:[26/06/2023]
Declaration of conformity
TTB826HDC by TITAN
EN
Declaration of conformity
(UK) DECLARATION OF CONFORMITY
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Object of the declaration
Product
Model
EAN
Pole Hedge trimmer 550W 50cm
TTB826HDC
5059340880785
The object of the declaration described above is in conformity with the relevant legislation:
Supply of Machinery (Safety) Regulations 2008 as amended
Noise Emission in the Environment by Equipment for Use Outdoors Regulations 2001 as amended
Electromagnetic Compatibility Regulations 2016 as amended
The Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 as amended
Measured Sound Power Level: 99.29 dB(A)
Guaranteed Sound Power Level: 105 dB(A)
References to the relevant designated standards used or references to the other technical specifications in relation to which
conformity is declared:
BS EN 62841-1: 2015
BS EN 62841-4-2: 2019
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 61000-3-2:2019 +A1
BS EN 61000-3-3:2013+A2
EN ISO 3744:1995
Authorised signatory and technical file holder:
Kingfisher International Products Limited
3 Sheldon Square
London W2 6PX
United Kingdom
David Awe
Group Quality Director
In more detail...
Product

Pole Hedge Trimmer 550W 50cm

TTB826HDC

Serial number: from 000001 to 999999
Name and address of the manufacturer or his authorised representative:
Kingfisher International Products Limited
3 Sheldon Square
London W2 6PX
United Kingdom
On [26/06/2023]
35
EN
Customer Care and Technical Helpline
TTB826HDC by TITAN
Customer Care and Technical Helpline
A better way to repair your tools
Kingfisher takes special care in creating high-quality garden power tools that are
designed to last. But if a fault develops with your garden power tool and you need
to claim under the guarantee, the Customer Care and Technical Helpline can
support with technical assistance or if required, arrange a free courier collection
from your home, assess your garden power tool for fault, repair it, and return it.
In more detail...
Deciding to repair your product rather than buying a replacement and adding to
the mountain of waste is a more sustainable choice and you will be doing your bit
for the environment.
How does it work?
Step 1
Find your proof
of purchase
and get in
touch with the
Customer Care
and Technical
Helpline.
Step 2
Chat to them
about the
problem with
your tool.
Step 3
Step 4
Step 5
They will provide The team will
Your repaired
technical and
assess and test tool will be
user advice or
and if necessary, returned to you
alternatively
repair your
via courier within
arrange a courier product back
5 - 7 working
collection from to full working
days*.
your home*.
order.
*please note that before collection, all fuel must be removed from
petrol powered machines.
Get in touch
If you need help or more information, please contact the Customer Care and
Technical Helpline:
UK: 0800 0789647
Eire: 1800 932226
Opening hours are Monday – Friday, 8am-5pm
36
TTB826HDC by TITAN
Availability of Spare Parts
EN
Availability of Spare Parts
Contact the customer service helpline for assistance or visit
www.kingfisherspares.com
For assistance contact the customer services helpline:
UK 0800 0789647 [email protected]
EIRE 1800 932226 [email protected]
In more detail...
Further information about this product can also be found at:
www.kingfisher.com/products
37
">