Advertisement
Advertisement
assembly Instructions For the models: • • • Kopenhagen / EN2 Larvik / E2 Lillehammer / EA2 • • • Brevik / EN3 Verdal / E3 Oulu / EA3 LinJa GmbH & Co. KG Unterdürrbacherstr. 222 97080 Würzburg Tel: +49 931 453 24 350 Email: [email protected] • • Molde / EN4 Ruka / EA4 Table of contents Foreword .................................................................................................................................................... 3 Important Instructions ............................................................................................................................... 3 Safety Instructions ..................................................................................................................................... 4 Usage tips ................................................................................................................................................... 4 Scope of delivery ........................................................................................................................................ 4 Assembly .................................................................................................................................................... 5 Step 1: Floor ........................................................................................................................................... 5 Step 2: Back- and Sidewalls.................................................................................................................... 5 Step 3: Bench ......................................................................................................................................... 5 Step: Front ............................................................................................................................................. 5 Step 5: Roof ............................................................................................................................................ 6 Step 6: Lamps ......................................................................................................................................... 6 Step 7: Sauna Stove ............................................................................................................................... 6 Transport.................................................................................................................................................... 6 Assembly Controller ................................................................................................................................... 7 Manual Controller ...................................................................................................................................... 9 DO-T ..................................................................................................................................................... 11 Installation ....................................................................................................................................... 11 Function ........................................................................................................................................... 11 Connecting the cables tot he control box................................................................................................ 13 Connecting the Sauna-Controller / Display ............................................................................................. 14 Connecting the temperature sensor........................................................................................................ 15 Connecting the sauna stove..................................................................................................................... 15 Foreword Dear Customer, We are pleased that you have chosen one of our products. Before unpacking the sauna, check the packaging for any damage! Before assembly, all parts must also be checked for damage and completeness. Before assembling and using this product, please read all the instructions and strictly follow the procedure. This sauna was designed in terms of design and functionality for private use. We are not liable for improper use of our products. Our products are subject to constant development. Therefore, there may be changes in the design and use of other components. Do you have questions regarding the product? Please contact us at: [email protected]. Our team will be happy to help you. Important Instructions Damage found when unpacking must be reported to us immediately with photos. Please send these to: [email protected] Two people (or three, depending on the size of the cabin) should set up the sauna, taking these assembly instructions into account. The power connection for the sauna must be carried out by a certified electrician. He must also ensure sufficient grounding to avoid accidents and malfunctions. Please have an electrician check the operation of the GFCI (if fitted).. When it comes to the statics of the floor, it must be ensured that it can withstand the total weight of the sauna and the people intended for it. Please note: The product is designed exclusively for private use. Please read the assembly instructions carefully first! If you still have questions about the construction, we will be happy to help you. Complaints arising from incorrect assembly or use are excluded from the warranty! . Note: The photos are for your reference only and may contain some variations Safety Instructions • • • • • • Never attach a door lock to the sauna! Never touch the oven and lamps with your hands when they are switched on! Make sure the sauna is adequately ventilated! Do not use the sauna if you have open wounds or burns! Do not use the sauna if you are pregnant! Consult a doctor before use if you suffer from any of the following problems: o you are elderly or ill o hyperthermalgesia o obesity o diabetes o high blood pressure o Heart & circulatory problems Usage tips • • • • • recommended temperature: 60 – 75°C The temperature displayed on the controller may differ from the temperature on the thermometer. Drink enough water Shower before use Do not go to the sauna immediately after eating or strenuous activities (e.g. sport).. Scope of delivery Count Element 1 Floor element 1 Ceiling element 1 Rear wall element 1 Front element with glass door 2 Side panel 1 Oven 1 Ladle with bucket 1 Hourglass 1 Thermometer 1 Accessories (screws, door handles and depending on the model 1-2 benches) Assembly Step 1: Floor Please align the floor in the desired location to start assembling the rear and side walls. Step 2: Back- and Sidewalls Please connect the side panels with the back wall panel and the floor panel by placing them on the grooves of the floor panel. Please align the buckles and then tighten them. Step 3: Bench Depending on the model, please install the front bench panel for one or two benches. To do this, slide it along the horizontal guide on the side panels. Be careful not to scratch the side panels. Then please install the seat by mounting it on the bench panel. Step: Front Now please mount the front panel by placing it on the grooves of the bottom panel. Again, please align the buckles and then tighten them. Step 5: Roof Now please put the roof on the sauna. Carefully lift the roof panel and place it on the four side walls. Once you have placed all four corners in the correct spot, gently press the roof down so that it is flush with all four corners. Step 6: Lamps Finally, to connect the lights for your sauna, please pull the cables through the small holes in the roof panel. The further cabling, as well as the power connection, takes place directly on the roof panel. Step 7: Sauna Stove Please pull the cable of the sauna heater from the inside to the outside through the small hole in the side wall. Although it is a 220-230V power supply, we recommend having the connection done by a professional. Transport Make sure the boxes are not exposed to moisture. Assembly Controller The display was built into the side wall for safe transport of the sauna. This must be removed to use the sauna. To do this, first remove the display surface by applying pressure to the clip on the top. Remove the 2 temperature sensor wires, black jacketed, and 5 connectors, white jacketed (7 wires total) from the controller. Warning: Be careful not to remove the flat white cable from the display! Instead of the display, the wooden bracket is built into the sauna wall. To do this, first pull all cables through the opening in the back of the holder. Reattach the cables to the controller and attach the controller to the bracket. Make sure the holes in the bracket are facing up to allow warm air to escape upwards. Reattach the display surface. Then screw the holder into the sauna wall in place of the controller's old position. Make sure the holes in the bracket are facing up to allow warm air to escape upwards. Manual Controller Temperature / duration setting: Pressing this button takes you to the setting of the desired temperature. The temperature display starts flashing and can be adjusted using the arrow buttons. By pressing the button again you switch to the setting for the duration of the sauna session. The time display starts flashing and can be set. Press the button again to exit settings. Alternatively, the last step happens automatically after 15 seconds. If the temperature in the sauna is higher than the set temperature, the LED lights up red and the heater switches off. If the temperature drops to 2°C below the set temperature, the oven switches on again and the LED lights up orange. DO-T Installation Sensor Control LIGHT TEMP ON/ OFF TIME Power 1700 mm Function Temperature display Lighting indicator LIGHT TEMP up and down key ON/ OFF TIME Work indicator ON / OFF: Starts or stops the steam generator. After switching on, the "Work" lamp lights up and the temperature display shows the temperature. Pressing it again switches the steam generator off again. LIGHT: Turns the lights on or off in the steam room. When the lights are on, the LIGHT indicator lamp will be lit. TEMP: Opens the temperature setting. The temperature can be set between 35°C and 55°C by pressing the arrow keys. TIME: Opens the duration setting. The duration can be set between 1 and 60 minutes using the arrow keys. If the temperature in the cabin is higher than the set temperature, steam production is stopped. If the temperature falls below 2°C less than the set temperature, the steam generator is switched on again. Sauna 4.5-9KW 200-240V ~ TAB KW 200-208V ~ 230-240V ~ Amp mm2 AWG Amp mm2 AWG 4.5 23 30 6 9 45 6 10 16 8 8 6 6 10 16 20 26 40 Sauna heaters Relay box 8 8 6 3XTAB * 3XTAB * Control Sensor 6X0.2mm2 * Use 90 C copper wire Relay box N L1 L2 L3 N U V W N 1 Sauna heaters Relay box Circuit board Control N N L1 L2 L3 1 2 3 4 5 6 1 2 3 4 5 6 7 8 Sensor 200-240V ~ Sauna 3-18KW 400V 3 ~ TAB KW 400V 3~ Amp mm2 3 4.5 2.5 4.5 6.8 4 9 6 4 9 13.6 6 AWG KW 400V 3~ Amp mm2 AWG 13 10.5 16 12 12 18 12 15 23 12 18 27 4 6 6 6 12 11 10 9 Relay box N L1 L2 L3 380V 3~ N U V W N 1 Sauna heaters Relay box 5XTAB * 5XTAB * Control Sensor 6X0.2mm2 * Use 90 C copper wire Sauna heaters Relay box Circuit board Control N N L1 L2 L3 1 2 3 4 5 6 1 2 3 4 5 6 7 8 Sensor Connecting the cables tot he control box After setting up your sauna cabin, the cables from the control display, temperature sensor and sauna heater must be connected to the silver control box on the roof of the sauna. This should only be carried out by a specialist! The necessary cables are on the side of the cables where the control box is located, taped to a side panel. Connecting the Sauna-Controller / Display Open the control box on the roof by unscrewing it. The white wire must be connected to the green circuit board. Pull the cable through the hole on the far left. Attach the connectors to the circuit board as follows: Left to right: Black, Brown, Red, Yellow, Green Connecting the temperature sensor Pull the temperature sensor cable through the ventilation opening in the ceiling and attach it to the ceiling with the bracket. Connecting the sauna stove The sauna stove must also be connected to the control box on the roof. 3-core cables are used for 3kw, 4.5kw or 6kw ovens. Pull the wire through the right hand opening in the control box and connect both the ground and all wires as shown in the picture: ">

Public link updated
The public link to your chat has been updated.
Advertisement