Estross Telecom ET-8848 User`s manual

ETROSS TELECOM (HONGKONG) LIMITED
301,3/F, Block B, Yuetong Comprehensive Bldg. Meilong Rd, Longhua, Bao’an District
Shenzhen China 518109
TEL:+86-755-26205464 FAX:+86-755-28167031
GSM FWT-8848 (Gateway
Gateway))
User's Manual
Brand: Etross
Model: ET-8848
Manufacturer
Manufacturer:: Shenzhen Etross TelecomCo.,Ltd
1
ETROSS TELECOM (HONGKONG) LIMITED
GSM FWT-8848 Version 1.1 -2010
1,General Description
GSM FWT-8848 is a GSM to Analog Converter(single port,insert 1 sim card only), the device
can produce a FXS line to allow a regular phone to be connected and used just like a local
landline(PSTN) except your calls will go out the GSM network. This device can both receive and
make calls.
The main application is: Connecting the RJ-11 FXS line to connect Ordinary telephone set for
voice call, to connect PBX for call extentions, to connect billing systems for public phone use, to
connect VoIP gateway to realize VoIP call termination, to connect alarm system for security
purpose, etc. It is not a VOIP gateway, nor a GSM+VOIP gateway, It is a GSM Fixed Wireless
Terminal that produces a Analog FXS phone line.
Available
Available::
�
GSM 900/1800Mhz dual band, employing Wavecom Q2303A, Q2403A,Q2406A, P3203A,
Sim300W ,SIM500W module to make;
�
GSM 900/1800/1900Mhz Tri-band, employing Sim300z module to make;
�
GSM850/900/1800/1900Mhz Quadband, employing M10,SIM340Z module to make.
�
Deatiled sub-models:
�
1)Dual band: ET-8848 Q2303A, ET-8848 Q2403A, ET-8848 Q2406A, ET-8848 P3203A,
ET-8848 Sim300W, ET-8848 SIM500W.
�
�
2) Tri- band: ET-8848 Sim300Z.
3)Quad band: ET-8848 M10, ET-8848 SIM340Z
Appearance and Structure
Item
GSM FWT-8848
Appearance
Remark
White/black
Material
ABS (Acrylonitrile Butadiene Styrene)
Dimension
170mm×118mm×30mm
Excluding antenna
2
ETROSS TELECOM (HONGKONG) LIMITED
Weight
400g
Power Switch
Rocker switch
Power Socket
12V DC input
Phone interface
RJ11
Antenna interface
SMA-female
No.1: Power, No.2.in use, No.3, in talk, No.4,
Weight of Main unit
2 RJ-11 ports
From left to right(front
LED display
Battery, if have, No. 5-7, Signal strength
Front side
Rear side
Bottom side
side view)
LEDs display for Signal strength, Power, Working
Status,Talking and Battery indicator;
1pcs SMA antenna connectors, 2 RJ-11
output,Power port and switch;
1pcs Sim card holder slots, you can insert Sim
card into the slot .
atures:
2,Fe
2,Features:
1) It is a 1 channel GSM Gateway which has 2 RJ-11 outputs for extensions;
2) It can connect with ordinary telephone set, PBX , VOIP Gateway, Billing meter etc. ;
3) Dialing tone frequency:450hz;
4) Employ Industrial module to make;
5) Can adjust dial interval from 0.5sec to 9 secs by setting up from telephone set;
6) Can adjust voice volume by setting up from telephone set;
7) SIM card supported (1.8V, 3V);
8) Caller ID display;
9) DTMF Dialing;
10) Bell signal;
11) Polarity reversal;
12) The RJ-11 socket which connect the phone or billing system for metering purpose;
13) Antenna socket (SMA);
14) IP Presetting;
15) Working status and Signal Strength by LED indicator;
16) IMEI Change (optional).
17) back up Li-ion battery( Optional) 7.2V 1300mAh.standby 24hrs,talking time: 2.5hrs.
3
ETROSS TELECOM (HONGKONG) LIMITED
Technical Specifications
3,
3,Technical
Air interface standard: GSM850/1900Mhz,900/1,800Mhz phase 2+ full band
Frequency ranges:
A) GSM 850
GSM 1900:
I) Transmission: 869.2 ~ 893.8MHz
I) Transmission: 1, 930 ~ 1, 990MHz
Ii) Reception: 824.2 ~ 848.2MHz
Ii) Reception: 1, 850 ~ 1, 910MHz
B) GSM 900:
GSM 1800:
I) Transmission: 890 ~ 915MHz
I) Transmission: 1, 710 ~ 1, 785MHz
Ii) Reception: 935 ~ 960MHz
Ii) Reception: 1, 805 ~ 1, 880MHz
Phone interface: supply RJ-11 Phone Interface
Hanging voltage: 45V
Picking off voltage: 30mA / 41mA
Dialing tone Frequency: 450Hz
Antenna interface: Antenna amplifying>2.5db
Sensitivity:<-104DBM
Transmitting power<3W
Color: White /Black (optional)
AC-Adapter interface: Input: AC 110~240VAC
50~60Hz
Output: 12DC 1A.
AC-Adapter type: EU,US,AU,British can be optional
Operation Circumstance:
4,
4,Operation
Operation temperature: -10c~60C
Storage temperature:-20C~70C
Operation humidity:45%-95%
Atmosphere pressure:86-106Kpa
Environment noise: <60DB
Transmitting Power:2W
Sensitivity: <-104dbm
Antenna Amplifying: >2.5db
Dialing frequency: 450Hz
Hanging voltage: 45V
Picking current: 30mA/41mA
Packing List
5,
5,Packing
Name
Quantity
Remark
GSM FWT-8848
1pcs
Dual band or Quadband
Ac- adapter
1pcs
AC-110-240V, DC12V/1A
Antenna
1pcs
Magnetic Antenna with 3m
4
ETROSS TELECOM (HONGKONG) LIMITED
cable
User's Manual
1pcs
English
G.W: 0.75kg per unit. 20pcs/CTN, 16kg /CTN,CTN Size: 55cmX34.5cmX32.5cm
6,Installation And Connection
The Condition for Installation
The terminal asks for 110- 220V AV power supply. It must be installed in the area where the
GSM network can cover. The strength of the signal can affect the quality of voice.
1. Screw off the screws that are on the back of the terminal, Insert SIM card for every Sim card
holder, and then tighten the screws.
2. Install antenna. In order to ensure the quality of voice, antenna must be put beyond 1.5 from
the telephone and terminal.
3. On end of the telephone line connects to the “Phone” port of the terminal, the other end
connects to telephone.
4. “Power” port connects to power adapter that is connected to 110-220V AC power supply.
1) The Installation for Connecting to Ordinary Telephone
The Sketch for connecting ordinary Telephone
Draw your attention: Because there are many types of ordinary telephone and their electric
parameters are different. In order to avoid mutual disturbance between telephone and terminal
and affect voice quality. The distance between telephone and terminal is 1.5m at least.
2) The installation for connecting to billing device for metering
If the users demand to register cost during calls, billing device can be connected between
terminal and ordinary telephone. Billing device register cost according to the anti-polarity signal
that is provided by terminal.
The sketch for connecting to Billing device or Computer charging system
5
ETROSS TELECOM (HONGKONG) LIMITED
3) The installation for connecting to PBX for call extentions
If users want to connect small PBX to this terminal, connect terminal’s “Phone port” to the PBX.
The sketch for connecting to PBX device.
4) The installation for connecting VoIP gateway for Call Termination
Suppose a VoIP call originates from US, which was transferred from US Server to China Server
on VoIP, finally the call will be terminated from internet to GSM network and to be sent out to the
destination answer side.
The sketch for connecting to VoIP gateway
6
ETROSS TELECOM (HONGKONG) LIMITED
5) The installation for connecting to alarm system for Security
The GSM FWT can substitute the PSTN for connecting to alarm system for security purpose
when PSTN failure or not available.
The sketch for connecting to alarm system
7, Function Setting
Before you do the following function settings, Lift handset or press hands free key of telephone
set, then you can press the buttons according to the following instructions to finish setting, you
will hear 2 beeps when you finish, this testify setting successfully.
1) Restore to factory default setting
*#99#99# restore to factory default setting.
2) Adjust dial interval
*#01#30# , 01--command,30--time,Max 9.9 seconds,Min 0.5 seconds, default setting is 3
seconds.
*If you use GSM FWT-8848 for connecting to VoIP gateway, you can set dial interval as 0.5
second, it can make PDD<5 sec (Method: *#01#05#);
7
ETROSS TELECOM (HONGKONG) LIMITED
*If you use GSM FWT-8848 for connecting telephone, PBX, billing device, you can set dial
interval as 3 seconds or 5 seconds as you like (Method: *#01#30#, set the dial interval as 3
seconds).
3) Adjust Earphone Volume
*#02#15#
02--command,15--volume,Max 16,Min 1, default setting is 15.
4) Adjust Mic. Volume (sensitivity)
*#03#10#
03--command,10--amount,Max 16,Min 1, default setting is 10.
5) Setting local area code
*#04#*0755#
10--command,*0755—area code,Max 5 numbers, use "*" instead if area code
is less than 5 digits.
6) Setting IP numbers
*#05#17911#
05--command,17911—IP numbers,Max 5 numbers, use "*" instead if IP number
is less than 5 digit.
Hide Caller ID (been sent out)
Setting
7)Hide
out)Setting
*#13#01#
13--command,01--value,Max-02,Min-00
Default setting is 00
00-- presentation indicator is used according to the subscription of the CLIR service
01 – CLIR allowed
02 – CLIR prohibited
Notice: This Setting need GSM carrier support.
8) Bar incoming call Setting
*#14#00#
14--command,00--value,00--no barring, 01--set barring
default setting --00
FSK setting (optional) (should confirm before order)
9)
9)FSK
*#17#00# setting caller ID
17-order, 00-value, 00-DTMF, 01-FSK, default setting is 00
This setting need terminal has FSK Chip set support
10
10)) Billing Mode setting
*#15#00#
15--command, 00-value, 01-reversal polarity, 02-12 KHz, 03-16 KHz, default setting-- 01
IMEI change Setting ( for Quad Band M10 and SIM540W modules only)
11
11)IMEI
1. Write IMEI to RAM
*#18#IMEI no.#, 18--command, IMEI No. --15-digits/numbers IMEI no.
2. Check IMEI, if it is right, and then write it to module.
*#19#IMEI no.#, 19--command, IMEI No. --15-digits/numbers IMEI No.
Notice: Step 1 and Step 2, IMEI no. must be same.
8
ETROSS TELECOM (HONGKONG) LIMITED
12) Pin Lock &Network Lock Setting (optional)(Should confirm before order)
2)PIN Lock
1, Set to open PIN code check and automatic PIN lock function
*#07#*1234# 07-command, 1234- the current SIM card PIN code
If set sucessfully, the device will open PIN code check, and automatically change the current
SIM Card into "PIN on" from "PIN off"
2, Set to close PIN code check and auomatic PIN lock function
*#08#*1234# 08-command, 1234- the current SIM card PIN code
If set sucessfully, the device will close PIN code check and automatic PIN lock function.
3, Set to change PIN code,open automatic PIN lock function
*#09#1234*56785678# 09-command, 1234- the current sim card PIN code, 5678-new PIN code.
(5678 can be any other 4 digits number, suppose you can use 2009).
If set successfully, the device will change the current sim card PIN code as you want.5678, or
the any other 4 digit PIN codes, and open automatic PIN lock function.
2)Network Lock
1,Set to open Network lock function
*#10#01234# 10-command, 01234-password
2,Set to close Network lock function
*#11#01234# 11-command,01234-password
3,Set the Network codes
*#12#1*46003*46003# 12-command,1--No. Of IMSI, 46003--the IMSI code for China Telecom
*#12#2*46000*46000# 12-command, 2--No. Of IMSI, 46000--the IMSI code for China Mobile
8,Making Calls and Answer Incoming Calls
Making Calls
1. Lift the handset or press “hand-free” key, you will hear dialing tone, then you can dial the
telephone numbers you want to call.
2. Dialing: dialing the telephone numbers you want to call
3. On completion of dialed digits, you can press “#” to transmit the called telephone
numbers. If you don’t dial any key for continual 3 seconds during the dialing, terminal
transmits called telephone numbers automatically.
4. During calls, if the telephone numbers is not free ones, the terminal sends out
anti-polarity signal.
5. If the calling party or called party hangs up, the terminal stops sending out anti-polarity
signal.
Answering Incoming Calls
When some calls are coming in, if the connected telephone has the function of displaying
incoming calls, the telephone rings and displays the incoming telephone numbers. Now
users can lift the handset or press “hand-free” to answer it.
9
ETROSS TELECOM (HONGKONG) LIMITED
Warranty Card
Please fill in the blanks carefully, and keep it properly as the voucher for warranty.
Type of Equipment
ET-8848
User’s name
Contact with:
Contact Tel.no.
Address
Date of Ex-works
Date of Maintenance
Sales Agent
Damage
Management
Maintainer
Purchasing Date
(Stamp)
10