Roper Rhodes HCCPAN / HCCTNK Harrow Close Coupled WC and Cistern Instructions

TRADITIONAL CLOSE COUPLED WC
Installation & care instructions
This product must be installed by a qualified fitter or plumber in accordance with and meet the requirements of the Water Supply (Water Fittings)
Regulations 1999 and Scottish Byelaws 2004
IMPORTANT
Flush out all impurities in the cistern prior to installation.
INLET VALVE SPECIFICATIONS
Water Temperature: 2°C - 45°C
Water Pressure: 0.2 Bar to 8 Bar
FILL VALVE INSTALLATION
SECURE CISTERN TANK ONTO PAN
Float Cup
FILL VALVE ADJUSTMENT
The fill valve is factory set but if
adjustment is required follow the
instructions below.
Cable to Lever Mechanism
Fixing bolt
Metal Washer
Rubber Washer
O-Ring
Cistern
Rubber Washer
Metal Washer
Nut
The fill valve is supplied set at a height suitable for the cistern tank.
Please ensure that all connections are fully tightened before
progressing.
Before assembling cistern to pan, wrap the inlet connector with PTFE
tape. Ensure that the float cup has room to move freely.
FLUSH VALVE INSTALLATION
Flush Valve Body
Rubber Seal
Rubber Washer
Rubber
Gasket
Toilet pan
Rubber Washer
Metal Washer
Wingnut
Mount the cistern to the WC pan as shown above. Ensure the gasket
is firmly sealed around the flush channel. Once assembled the toilet
can be positioned and installed in location. Before securing the pan to
the floor, drill the holes in the wall for securing the cistern tank. After
securing the pan to the floor, attach the tank to the wall using fixings
suitable for the installation in hand (not supplied).
Connect the waste outlet of the pan to a suitable new waste connector. Do NOT use silicone sealant as this can impair the sealing of
rubber components.
Valve Cradle
Nut
Water Supply
1/2” BSP
Flush Valve Cradle
FLUSH VALVE ADJUSTMENT
The flush valve is factory set but if adjustment is required see diagram
below.
Plastic Washer
Rubber Gasket
FULL ADJUSTOR
Ensure that the Flush Valve is assembled and fully tightened as
shown.
The Flush Valve Body can be easily removed if necessary. Rotate
clockwise to remove. To replace align slot of body with slot in valve
cradle and rotate anti-clockwise until you hear a click.
The valve is set correctly at the factory. However there are
levers on the left side for full flush and on the right hand side for
reduced flush operation which can be adjusted if necessary.
Fine Adjustment
Turn screw for fine
adjustment of float
height.
Anticlockwise to
lower float.
Clockwise to
heighten float.
Reduced Flush
Factory Setting ‘2’
HALF ADJUSTOR
Factory Setting ‘3’
Factory Setting ‘4’
HANDLE ASSEMBLY
Assemble the cistern handle through the round hole on the corner of
the cistern tank as shown.
Once the handle is secured, fasten the lever mechanism housing on
the end of the flush valve cable to the handle’s shaft. Ensure that the
splines on the shaft align with the slots in the mechanism housing.
Once located, with the metal grip bracket in place, secure the
lever shaft to the housing with the housing nut.
Check that the lever can move both up and down. If not undo and
re-assemble, checking that the valve operates in both directions.
Important: Connect the
Cistern Lever
water supply to the cistern
Plastic Washer
using an approved double
Rubber Washer
check valve to fluid
Cistern Tank
category 3 in addition to
Lever Mechanism
an accessible service
Housing
valve. Turn on the water
Turquoise Nut
supply and check all
connections for leaks,
re-tightening any
connections as necessary.
Ensure that the water fills
to the level indicated
inside the ceramic cistern.
Once satisfied place the
Cable to
Metal grip bracket
Flush Valve
cistern lid in place.
Mechanism Housing Nut
Up = Reduced Flush
Down = Full Flush
REF: AG.07.20 v2
">