Integrated Technical Vision Ltd.
A programmable reader for mobile and
RF identifiers U-Prox mini
User manual
Introduction
U-Prox ID reader is intended to be applied in different access control
systems, using RS232, Wiegand 26, Wiegand 37, Wiegand 42,
Wiegand auto. Personification mode of U-Prox IDentifiers is supported
by setting an additional encryption mode.
Identifiers types
U-Prox-mini proximity readers operate with U-Prox ID and ASK and/or FSK
IDs. The reader settings, the interface and the identifiers types, which are
allowed to work with, can be changed by using mobile application. The reader
can be programmed to work with ASK and/or FSK and/or U-Prox ID. The
functioning of ASK and FSK IDs will be disabled automatically, while
switching on U-Prox ID personification mode.
Design
The reader is placed in elegant plastic case with its future hermetization. Due to the small overall
dimensions, U-Prox-mini possesses increased reliability and strength.
Benefits
Case
Ambient
Conditions
Power
Supply
Material
Color
Dimensions
Weight
Oper. temp.
Humidity
Voltage
Current
Max current
Voltage ripple
ABS plastic
black, gray, white
80 х 45 х 12,5 mm
70 g
-35°C . . . +60°C
100% rel. at +25 0C
+5. . . +15 VDC
up to 40 mA
up to 50 mA
up to 500 mVp-p
Read range
Typical read range is 50-100 mm and depends on tag
type used with it. Read range of U-Prox ID is up to 0.5
m. With a supply voltage of +13.5 V and the voltage
ripple up to 50 mV, standard read range for EM-06
identifiers is 80 ... 100 mm, while placing them in
parallel to case.
Wiring
Reader has 8 wire cable for connecting to access
control panel. The reader terminal functions are listed
in the table above (+ V external source +12 V): We
recommend using multi-core
signal cable with 0.22 mm2
cross-section of each wire
between reader and panel.
Using such cable, maximum
panel read range is up to
150 m (Wiegand interface).
Using a twisted pair to
connect reader, you should
follow the Figure 1.
http://www.itvsystems.com.ua
Colour
Green
White
Red
Black
Brown
Orange
Blue
Yellow
W2 / W3 /
RS232
W4 / WS
Functions
Data 0
Rx
Data 1
Tx
+V
+V
GND
GND
Red Led
Green Led
Beep
Hold
Hold
DB-9
3
2
5
Figure 1
1
Integrated Technical Vision Ltd.
Types of interfaces
Depending on modification, reader supports one of the
following interfaces: Wiegand 26, 37, 42 or standard with
automatic selection (W2, W3, W4, WS) and RS-232C (RS).
Mounting
We recommend to install reader on the wall next to the door
from the lock side. Reader should be installed in the way that is
convenient for all users. You should make small recess or hole
(diameter is 14 mm) to connect cable under the reader's case.
Do not place the reader on metal surfaces, since it causes
decreasing of read range. If more than one reader is used
in the system, place them not closer than 20 cm one from
another to eliminate the effect of double reading.
Reader Installation
Loosen the screw at the bottom of the reader.
Remove the top cover and detach the back
plate.
Use reader back plate as a template, mark
out and drill two holes (diameter – 5mm,
depth–30mm) at this place (see Fig. 2).
Pass cable into the central hole; fasten the
back plate to the wall, using supplied plastic
dowels and screws. Connect reader with
cable, which attaches it to panel.
Insert reader into the back plate, put the top
cover and tighten it with a screw.
Figure 2
Figure 3
The Reader Operation
RFID Card Code Reading
Code is read when a valid non-contact ID is passed.
Card code reading is annunciated by embedded buzzer and LED lamp according to the interface
type and annunciation mode (see Section «Data transfer and Annunciation»).
Repeated reading will be available after 0.8 sec only if card is removed from the reader sensing
area.
U-Prox ID code reading
Download and install mobile software U-Prox U-Prox ID. It enables to receive,
store U-Prox ID and transfer ID code between reader and smartphone.
Full description of mobile application U-Prox U-Prox ID operation you can find at the
link: http://u-prox.com/UPROXIDEN
Hold mobile device near the reader (standard distance is 10-40 cm) and press
the button
The application will execute data exchange. The card code reading is
annunciated by embedded buzzer and LED according to the interface type and
annunciation mode (see Section «Data transfer and Annunciation»)
U-Prox ID(Android)
Hold Mode
Reader is turned to the hold mode while yellow wire is shorted to ground. In
this mode, reader does not read cards that reduces the current consumption
to 25 mA.
Relay or an open collector transistor can switch on hold mode.
It is prohibited to supply the external voltage to the yellow wire!
http://www.itvsystems.com.ua
U-Prox ID (Apple iOS)
2
Integrated Technical Vision Ltd.
Data transfer and Annunciation
Reader has two-colour LED indicators and buzzer.
LED and buzzer control depends on the interface type.
Wiegand Interface
Engaging of LED and buzzer is automatic or by grounding of corresponding wire (see Section
«Wiring»)
Annunciation mode:
Buzzer
00
01
02
03
04
05
06
07
08
Beep on card read
Control from outside
Beep on card read
Control from outside
Beep on card read
Control from outside
Beep on card read
Control from outside
Beep on card read
Possibly to control
from outside
Red LED
LED normally on, switch off at reading
LED normally on, switch off at reading
Switch off
Switch off
LED normally on, switch off at reading
LED normally on, switch off at reading
Control from host
Control from host
LED normally on, switch off at reading
Possibly to switch off from outside
Green LED
Blinking at reading
Blinking at reading
Blinking at reading
Blinking at reading
Control from host
Control from host
Control from host
Control from host
Blinking at reading
Possibly to switch on from
outside
Data transfer from the reader corresponds to the specified standard.
Interface RS232
ID reading is accompanied by transferring the packet with its code to panel.
Transmission of control packet to the reader is required, to control annunciation. Packets should
be transmitted with 2 400 bps rate, 8 bit data, no parity, 1 stop bit.
Personalization mode
Reader supports mode in which it reads only those U-Prox ID codes that are encrypted with the known
encryption key, set during programming.
Reader programming
Download and install mobile software U-Prox Config. The reader is fully configured with
it.
Run the reader in the programming mode –short D0 (green) and D1 (white)
terminals with each other and power up the reader.
Attention!!! «To access, shorten green and white wires and then restart reader»
message appears in the program window in case of unauthorized connection attempt
(D0 and D1 terminals aren’t shorted).
U-Prox Config (Android)
Start U-Prox Config, press "Search" button and then device search will be started.
After scanning, select reader from list and press "Connect" button to upload reader
settings.
Main application menu available for the reader settings adjustment, up- and
downloading, save or restore reader settings for future use (as template) and
update its firmware, after sucsessful upload. You can check the serial number and
firmware version of device, set ID types for reader operation, type of front-end
interface and annunciation modes in the "Settings" section.
U-Prox Config (iOS)
You can also switch on personification mode by setting encryption password of U-Prox IDentifiers (8
symbols).
Item "Record to device" will be available in the main menu after setting up reader. Application downloads
new settings into the reader after ‘Record to device’ button press.
http://www.itvsystems.com.ua
3
Integrated Technical Vision Ltd.
Full description of mobile application U-Prox U-Prox ID operation you can find at link:
http://u-prox.com/UPROXCFGEN
Limited Warranty
The manufacturer guarantees the correspondence of U-Prox mini reader to the requirements of
technical regulations ETSI EN 300 330-2 V1.5.1 (2010-02); IEC60839-1-3-2001; EN 50385: 2007
during warranty period of storage and operation under the fulfillment of transportation, storage and
operation conditions, that are established by technical specifications.
Warranty period of storage is 6 months from the date of manufacture. Warranty period of operation is
18 months from the date of purchase.
If a defect caused by the fault of the manufacturer is identified, the manufacturer will provide the defect
removal within 10 days from the date of receiving the complaint.
Consumer will be deprived of warranty service, in case of commissioning or repair work by an
organization that does not have the authority of the manufacturer to carry out those works.
For warranty services, please contact:
Certificate of acceptance
Reader U-Prox mini, serial number
..... ................ ...... ...................... .. ...... ...............
corresponds to ETSI EN 300 330-2 V1.5.1 (2010-02);
IEC60839-1-3-2001; EN 50385: 2007; and is considered
usable.
Content
1. Reader - 1 pc.
2. Passport with instructions.
3. Screw - 2 pcs.
4. Dowel - 2 pcs.
5. Individual package.
QC passed
Date of sale "____" ___________ 20 ___ y.
http://www.itvsystems.com.ua
4
">
