E5828B/E1828B 5.8 GHz corded/cordless

Quick start guide
E5828B/E1828B
5.8 GHz corded/cordless
telephone/answering
system with caller ID/
call waiting
Battery installation & charging
After installing the battery, you may be able to make or receive short calls. For
best performance, place the handset in charger to charge for 16 hours before
use.
You can keep the battery charged by returning the handset to charger after use.
When the battery is fully depleted, a recharge takes about 12 hours. The average
talk time on a fully charged battery is about five hours, and the standby time is
approximately six days. Actual battery life depends on usage conditions and age
of battery.
NOTE: Under normal conditions,
the battery should last approximately
one year. This may vary depending on
usage.
Caution: Use only the supplied
rechargeable battery, replacement battery 2422 (SKU 23402, part number
To
order a replacement battery, visit our website at
www.telephones.att.com
or call 1 (800) 222-3111.
In Canada dial 1 (866)
288-4268.
89-0047-00-00) or equivalent.
1. Insert the plug as
indicated. Be sure to
securely insert the
plug, making sure
that it matches the
color-coded label
inside the battery
compartment.
2. Place the battery and wires
inside the compartment.
3. Slide the battery compartment cover up
until it clicks.
Choose a central location close to a telephone jack and a electrical outlet
not controlled by a wall switch. The telephone base can be placed on a flat
surface or mounted on a standard wall plate. For optimum range and better
reception, place the telephone base in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers, television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11) or
other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave ovens,
refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.
Telephone base installation
1. Plug the small end of the larger power adapter into the power
jack at the bottom of the telephone base.
2. Plug one end of the tele-
3. Route cords through
phone line cord into the telephone jack at the bot­tom
of the telephone base.
slots.
DSL filter
(Optional for DSL users, see number
four in the note section, below.)
Telephone line cord
4. Plug the large end of
5. Plug the other end
the larger power adapter
into an electrical outlet
not controlled by a wall
switch.
of the telephone line
cord into a telephone
jack.
6. Plug one end of the coiled handset cord into the
jack at
the bottom of the telephone base. Plug the other end of the
coiled cord into the base handset.
6. Plug the small end of
the smaller power adapter
into the jack on the underside of the charger, then
route the cord through the
slot as shown.
7. Plug the large
end of the smaller
power adapter into
an electrical outlet
not controlled by a
wall switch.
8. You may be able to
make or receive short
calls. For best performance, place the handset in
the charger to charge for
at least 16 hours before
first use.
NOTES:
To order a replacement power adapter, visit our website at www.telephones.att.com,
or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
1. Use only the power adapter supplied with this product or equivalent.
2. Be sure to use an electrical outlet not controlled by a wall switch.
3. This power adapter is intended to be correctly oriented in a vertical or floor mount position.
4. If you receive high speed internet through your telephone line (commonly referred to as DSL), and
you are experiencing interference during telephone conversations and/or your caller ID features
are not functioning properly, install a DSL filter to the telephone line between the telephone base
and the telephone wall jack. Contact your DSL service provider for a DSL filter.
Quick reference guide
Cordless handset
DIR /VOLUME+
SELECT/TRANSFER
Press to store a programming
option, or to create a directory entry
in memory. During a call, press to
transfer a call between cordless
handsets.
CID/-VOLUME
When phone is idle, press CID to
display caller ID information. While
entering names or phone numbers,
press to move the cursor to the
left. While programming, press to
change menu item or value. During
a call, press CID to adjust listening volume.
PHONE/FLASH
Press to make or answer a call.
During a call, press to receive an
incoming call if call waiting is activated.
When phone is idle (not in use),
press DIR to display directory
entries. While entering letters in
names, press to advance or press
twice to enter space. While programming, press to change menu
item or value. During a call, press
DIR to adjust listening volume.
OFF/CLEAR
During a call, press to hang up.
While using menus, press to cancel an operation, or exit the menu
display.
INT/DELETE
While phone is idle, press to page
base or press and hold to delete all
caller ID entries. While a caller ID
entry is displayed, press to delete
displayed entry.
REDIAL/PAUSE
HOLD
Press to place a call on hold. Press
again to resume your call.
Before dialing, press to display the
last number called. While dialing or
entering numbers into your directory, press to insert a four-second
dialing pause.
MENU/CHAN
Press to customize the handset’s
operation. During a call, press to
switch to another channel if there is
interference.
Feature menu
DIRECTORY
Feature menu
Using menus
DIRECTORY
SPEED DIAL
RINGER
DATE/TIME
LANGUAGE
Press CID/-VOLUME or DIR /VOLUME+
to scroll through menu items.
Press SELECT/TRANSFER to select or
modify a highlighted item.
Press
OFF/CLEAR to cancel an operation, or exit the menu display.
NOTE: For more information, please refer to the user's manual.
Quick reference guide
Telephone base
RINGER VOLUME:
CONTRAST: Press to adjust
Adjust
switch on side of base (off, low,
high).
•
screen contrast.
•
•
•
•
•
INTERCOM/CID DEL:
Press to delete displayed
caller ID entry. While phone
is idle, press to page handset, or press and hold to
delete all caller ID entries.
•
MENU: Press to customize
•
FLASH :
•
REDIAL/PAUSE:
the telephone’s operation.
During a call,
press to receive an incoming call if call waiting is
activated.
Before
dialing any numbers, press
to display the last number
called.
While dialing or entering
numbers into your directory, press to insert a foursecond dialing pause.
•
CLOCK:
•
SETUP: Press
clock.
Press to review or set
repeatedly to hear
setup options.
ANNC.: Press to review or record
announcement; press again to
quit.
• RECORD : Press to record a
memo or after pressing ANNC.
to record an outgoing announcement.
•
•
•
•
•
•
PLAY/STOP: Press to start or
stop message playback.
DELETE: Press to delete message currently playing, hold to
delete all old messages.
ANSWER ON: Press to turn
answering system on or off.
REPEAT : Press to repeat message, press twice to play previous
message.
SKIP : Press to skip message.
NOTE: For more information, please refer to the user's manual.
CLEAR:
While using
menus, press to cancel an operation, or
exit the menu display.
CID : Press when
phone is idle to display caller ID information. While entering
numbers or letters,
press to move the cursor to the left.
SELECT : Press to
store a programming
option, or to create
a directory entry in
memory.
DIR : Press when
phone is idle to display
directory entries. While
entering or modifying names, press to
advance cursor.
DISP DIAL: Press to
dial number currently
displayed.
•
HOLD: Press to place
•
SPEAKER: Press to
activate the Clearspeak™
dial-in-base speakerphone. The Clearspeak™
speakerphone allows
clear, hands-free communications when you
are positioned near the
telephone base.
call on hold. Press
again to resume call.
• VOLUME : During
a call, press
or
to adjust listening volume.
• MUTE: Press to silence
microphone, press again
to resume your conversation.
www.telephones.att.com
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 5 AT&T 10/07.
96-006373-040-100