Epson PowerLite 715c Specifications

EPSON PowerLite 505c/715c Projector
lens ring
memory
card light
Projector Specifications
remote control
receiver
speaker
General
focus ring
foot
release
lever
memory
card slot
foot
foot release
lever
foot
Type of display
Poly-silicon Thin Film Transistor (TFT)
Size of liquid
crystal panels
Diagonal: 0.9 inch (22.9 mm)
Lens
F=2.0 to 2.2, f=35 to 42 mm
Resolution
1024 × 768 pixels (715c native format)
800 × 600 pixels (505c native format)
Color reproduction 24 bit, 16.7 million colors
Brightness
1200 lumens (ANSI) 715c
1100 lumens (ANSI) 505c
Contrast ratio
400:1
Image size
(diagonal)
26 to 300 inches
lens cap
Projection distance 3.6 to 45.5 feet (1.1 to 13.8 meters)
Projection methods Front, rear, upside-down (ceiling mount)
Internal sound
system
control panel
buttons
1 W monaural
Optical aspect ratio 4:3 (horizontal:vertical)
Zoom ratio
1:1.2
Noise level
42 dB
warning
lights
Keystone correction
angle
±15° (maximum)
power
inlet
Card slot
PCMCIA Type II
Kensington
lock port
Card
Supports CFA specification
CompactFlash,™ SmartMedia,™
Memory Stick,™ ATA Flash (both 3.3 V
and 5 V), and Microdrive™
USB port
A/V computer connector
jacks
PS/2 mouse
port
Projection Lamp
audio jacks
S-video connector
Type
UHE (Ultra High Efficiency)
Power
consumption
150 W
Lamp life
About 1000 hours
Part number
ELPLP14
Remote Control
Range
32.8 feet (10 meters)
Batteries
Alkaline AA (2)
Mouse Compatibility
Supports PS/2, USB, ADB
1/01
EPSON PowerLite 505c/715c Projector - 1
EPSON PowerLite 505c/715c Projector
Dimensions
Mode
Refresh Rate (Hz)
Resolution
8.4 inches (213 mm)
VGAEGA
70
640 x 350
Depth
10.5 inches (267 mm)
Weight
6 lb (2.7 kg)
VGA60
VGA72
VGA75
VGA85
VGA Text
VGA Text
59.94
72.809
75
85.008
70.087
70.087
640 x 480
640 x 480
640 x 480
640 x 480
720 x 350
720 x 400
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
56.25
60.317
72.188
75
85.061
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
XGA43i
XGA60
XGA70
XGA75
XGA85
43.476
60.004
70.069
75.029
84.997
1024 x 7681
1024 x 7681
1024 x 7681
1024 x 7681
1024 x 7681
SXGA1—70
SXGA1—75
SXGA1—85
70.012
75
84.999
1152 x 8642
1152 x 8642
1152 x 8642
SXGA2—60
SXGA2—75
SXGA2—85
60
75
85.002
1280 x 9602
1280 x 9602
1280 x 9602
SXGA3—43i
SXGA3—60
SXGA3—75
SXGA3—85
43.436
60.02
75.025
85.024
1280 x 10242
1280 x 10242
1280 x 10242
1280 x 10242
UXGA60
60
1600 x 12003
MACII13
MAC16
MAC19-60
MAC19
MAC21
66.67
75.087
59.28
74.93
75.062
640 x 480
832 x 6241
1024 x 7681
1024 x 7681
1152 x 8702
HDTV525I
HDTV525P
HDTV750P
HDTV1125I
HDTV1125I
HDTV1125P
HDTV1125P
59.94
59.94
60
60
50.04
60
50
640 x 4802
640 x 4802
1280 x 7202
1920 x 10802
1920 x 10802
1920 x 10802
1920 x 10802
NTSC
PAL
SECAM
60
50
50
640 x 4802
720 x 5402
720 x 5402
Height
2.8 to 3.4 inches (72 to 87 mm)
Width
Electrical
Rated frequency
50 to 60 Hz
Power supply
100 to 120 VAC, 1.9 A
200 to 240 VAC, 1.0 A
Power
consumption
Operating: 230 W
Standby: 5 W
Environmental
Temperature
Operating: 41 to 95 °F (5 to 35 °C),
Storage: 14 to 140 °F (–10 to 60 °C),
Humidity
Operating: 20 to 80% RH,
non-condensing
Storage: 10 to 90% RH,
non-condensing
Safety
United States
FCC Part 15B Class B
UL1950 Rev. 3
Canada
DOC ICES003 Class B
CSA C22.2 No. 950 Rev. 3
CE Marking
Directive 89/336/EEC, 92/31/EEC
EN 60950
Compatible Video Formats
The projector supports NTSC, HDTV, PAL, and SECAM
international video standards, as well as the monitor display
formats listed below.
To project images output from a computer, the computer’s
video card must be set at a refresh rate (vertical frequency)
that’s compatible with the projector; see the following table
for compatible formats. As noted below, some images are
automatically resized to display in one of the projector’s
“native” formats (such as XGA). In addition, the frequencies
of some computers may not allow images to display correctly;
see your computer’s documentation for details.
2 - EPSON PowerLite 505c/715c Projector
1/01
1
The image is resized so that it displays using one of the projector’s
native formats (PowerLite 505c only).
2
The image is resized so that it displays using one of the projector’s
native formats (PowerLite 505c and 715c).
3
Not supported on the PowerLite 505c.
EPSON PowerLite 505c/715c Projector
The distance from the projector to the screen determines the
actual size of the projected image. Use the general guidelines
in the table below to determine the proper distance.
Computer Connector Pin Assignments
The Computer/Component video port is a female video RGB,
15-pin micro-D-style connector. The pin assignments are:
Input pin Computer connector signals
1
Red video
2
Green video
3
Blue video
4
Monitor (ID bit 2)
5
GND
6
Red video GND
7
Green video GND
8
Blue video GND
9
+5 V
10
Synchronous GND
11
Monitor (ID bit 0)
12
SDA
13
Horizontal sync
14
Vertical sync
15
Reserved
Image size
(diagonal)
Horizontal distance from projector to
screen
30 inches
3.6 to 4.3 feet (1.1 to 1.3 meters)
40 inches
4.8 to 5.8 feet (1.5 to 1.8 meters)
60 inches
7.4 to 8.9 feet (2.2 to 2.7 meters)
80 inches
9.9 to 11.9 feet (3.0 to 3.7 meters)
100 inches
12.4 to 15.0 feet (3.8 to 4.6 meters)
120 inches
15.0 to 17.7 (4.6 to 5.4 meters)
150 inches
18.7 feet to 22.6 (5.7 to 6.9 meters)
200 inches
25.0 to 30.2 feet (7.6 to 9.2 meters)
300 inches
37.6 to 45.5 feet (11.5 to 13.9 meters)
Starting Up the Projector
Projector Placement Guidelines
Follow these steps to start up the projector:
1. Connect one end of the power cord to the projector’s power
inlet.
❏ Place the projector on a sturdy, level surface, between
3.6 and 45.5 feet from the screen.
❏ Make sure there is plenty of space for ventilation around and
under the projector.
❏ Make sure the projector is within 6 feet of a grounded
electrical outlet or extension cord. If you’re using a computer
and/or video source, locate them within 5 feet of the
projector.
power light
❏ Place the projector directly in front of the center of the
screen, facing it toward the screen squarely. Otherwise, your
image will not be square.
2. Connect the other end to a grounded electrical outlet.
The power light on top of the projector turns orange,
indicating that the projector is receiving power but not yet
turned on.
1/01
EPSON PowerLite 505c/715c Projector - 3
EPSON PowerLite 505c/715c Projector
6. Do one of the following:
3. Use the tab on the lens ring to rotate the ring and extend the
lens.
❏ If you’re presenting without a computer, you may see the
EasyMP main screen. Use the Enter button on the
remote control to select your presentation, then press
Enter to start it. See the User’s Guide for more information.
tab
If a presentation starts automatically, you may need to
press Enter to change slides.
❏ If you’re using a computer, turn it on or restart it. In a
few moments, you should see your computer display
projected. If you see an EasyMP screen or presentation
instead, press the Source button on top of the projector
to switch to the computer.
4. Squeeze the lens cap tabs and remove the lens cap.
(Windows® only: If you see a message saying that it has
found a plug-and-play monitor, click Cancel.)
Squeeze here
❏ If you’re projecting a video, press the Source button on
top of the projector to switch to your video source, and
press the Play button on your DVD player or other video
device.
If a projected image fails to appear, see the next section for
help.
Once you see your image, turn to page 5 for instructions on
focusing and making other image adjustments.
Caution: Do not use the projector with the lens cap in place.
The heat generated by the lens can damage the cap.
When you’re done with your presentation, shut down the
projector as described on page 6. Shutting down the projector
correctly prevents premature lamp failure and possible damage
from overheating.
5. Press the red Power button on top of the projector.
Power
button
What To Do If You See a Blank Screen
If you see a blank screen or a blue screen with the message No
Signal after turning on your computer or video source, try the
power light
following:
❏ Make sure the cables are connected correctly, as described in
the User’s Guide.
❏ Make sure the power light is green and not flashing and the
lens cap is off.
The power light flashes green as the projector warms up, and
the projection lamp comes on in about 30 seconds. The
power light stays green.
❏ Try restarting your computer.
❏ Press the Source button on top of the projector to select the
correct source. (Allow a few seconds for the projector to sync
up after pressing the button.)
You may see the EasyMP™ main screen or a presentation
that has been saved on the memory card and set to run
automatically.
Warning: never look into the lens when the lamp is on. This
can damage your eyes, and is especially dangerous for children.
4 - EPSON PowerLite 505c/715c Projector
1/01
EPSON PowerLite 505c/715c Projector
If you’re using a PowerBook:
Adjusting the Height of Your Image
You may need to set up your system to display on the
projector screen as well as the LCD screen. Follow these steps:
If the image is too low, you can raise it by extending the
projector’s feet.
1. From the Apple® menu, select Control Panels, then click
Monitors and Sound.
1. Stand behind the projector. Pull up the blue foot release
levers and lift the front of the projector. This unlocks the
feet.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other.
If this option isn’t available, you may need to select one of the
Simulscan resolution settings:
1. Click the Monitor icon.
2. Select a Simulscan resolution. (Allow a few seconds for the
projector to sync up after making the selection.)
If you’re using a PC laptop:
❏ Hold down the Fn key and press the function key that lets
you display on an external monitor. It may have an icon such
as
or it may be labelled CRT/LCD. Allow a few
seconds for the projector to sync up after pressing it. Check
your laptop’s manual or online help for details.
Caution: Do not hold the projector by the lens; this can
damage it.
2. Once the image is positioned where you want it, release the
levers to lock the feet in position.
On most systems, the
key lets you toggle between the
LCD screen and the projector, or display on both at the
same time.
3. To fine-tune the height of the image, rotate the thumb
wheels attached to the projector’s feet.
❏ Depending on your computer’s video card, you might need
to use the Display utility in the Control Panel to make sure
that both the LCD screen and external monitor port are
enabled. See your computer’s documentation or online help
for details.
If the image is no longer square after raising it, see the next
section.
Adjusting the Image Shape
If the projected image isn’t square or has a “keystone” shape,
try the following:
Focusing and Zooming Your Image
❏ If your image looks like
or
, you’ve placed the
projector off to one side of the screen, at an angle. Move it
directly in front of the center of the screen, facing the screen
squarely.
Rotate the focus ring to sharpen the image.
lens ring
tab
❏ If your image looks like
or
, press the + or —
side of the Keystone button to correct the shape of the
image. After correction, your image will be slightly smaller.
focus ring
Keystone button
Use the tab to rotate the lens ring and reduce or enlarge the
image.
You can also change the image size by moving the projector
closer to or farther away from the screen. You can use the
E-Zoom button on the remote control to zoom in on a portion
of the image. See the User’s Guide for instructions.
1/01
EPSON PowerLite 505c/715c Projector - 5
EPSON PowerLite 505c/715c Projector
Shutting Down the Projector
Projector Status Lights
When you’ve finished using the projector, follow the
recommended procedure to shut it down. This extends the life
of the lamp and protects the projector from possible
overheating.
Note: When the projector has not received any input signals for
30 minutes, it automatically turns off the lamp and enters “sleep
mode.” This conserves electricity, cools the projector, and extends
the life of the lamp. If you are done using the projector, unplug the
power cord. If you want to start projecting again, press the Power
button.
power light
lamp light
temperature
light
1. If you’re using a computer, shut it down first.
The lights on top of the projector indicate the projector’s
status and let you know when a problem occurs.
2. To turn off the projector, press the red Power button on the
projector or remote control. You see a confirmation message.
(If you don’t want to turn it off, press any other button.)
Light
3. Press the Power button again. The power light flashes
orange for about a minute as the projector cools down.
When the projector has cooled, the orange light stays on and
the exhaust fan shuts off.
If you want to turn the projector on again, wait until the
orange light stops flashing. Then press the Power button.
Caution: To avoid damaging the projector or lamp, never
unplug the power cord when the power light is green or
flashing orange.
4. Replace the lens cap, retract the lens, and unplug the power
cord.
5. If you’re using a VCR or other video source, turn it off after
you turn off the projector.
6. Disconnect all equipment, and store the projector in the bag
that came with it or in a protective case.
6 - EPSON PowerLite 505c/715c Projector
1/01
Status
Description and action
orange
The projector is in sleep mode. You can unplug
it or press the Power button to turn it on.
flashing
green
The projector is warming up. Wait for the image
to appear.
green
The projector is operating normally.
flashing
orange
The projector is cooling down. You can’t turn
the projector on (and should not unplug it) until
the light stops flashing and remains orange.
flashing
red
Power is cut off because of an internal
problem. Remove the power cord and contact
EPSON for help.
red
The lamp is burned out. Replace it as
described on page 10.
flashing
orange
The lamp is almost burned out. This is a good
time to replace it, following the instructions on
page 10.
flashing
red
There is a problem with the lamp, power
supply, fuse, or circuit. If necessary, replace
the lamp as described on page 10.
flashing
orange
The projector is in a high-temperature cooling
cycle. Make sure the temperature surrounding
the projector does not exceed 104 °F and there
is plenty of space around and under the
projector for ventilation. Clean the air filter if
necessary. See page 9 for instructions.
red
The projector has turned off automatically
because it has overheated. Let it cool for a few
minutes, then turn it back on. Make sure
nothing is blocking the vents on the front and
top of the projector. If it continues to overheat,
you may need to change the air filter. See
page 9 for instructions.
flashing
red
There is a problem with the cooling fan or
temperature sensor. Turn off the projector and
unplug it. Contact EPSON for help.
EPSON PowerLite 505c/715c Projector
This table summarizes the functions on the remote control.
Using the Remote Control
The remote control lets you access all of your projector’s
features from anywhere in the room (up to 30 feet away). You
can use it to turn the projector on and off, zoom the image,
and highlight your presentation, for example.
You can also use the remote control for EasyMP presentations
without a computer.
Button
Function
Power
Starts or stops the projector.
Freeze
Keeps the current computer or video image on the
screen.
A/V mute
Turns off the audio and video, displaying the black, blue
or user logo background.
E-Zoom
Enlarges or reduces the image size from 1x to 4x (in 24
steps). Pressing the right side of the button enlarges the
image, pressing the left side of the button reduces the
image. To display a portion of an enlarged image which is
outside the display area, press the Enter button and scroll
the image to the desired location.
IR output
Power
Freeze
Power
Freeze
A/V Mute
A/V Mute
E-Zoom
3
5
1
2
4
Special
highlighting
effects buttons
Remote
control on/off
R/C ON
OFF
E-Zoom
Enter
Enter
Illumination
Turns the remote control on or off.
Button 1
Places a pointer or cursor stamp on the screen.
Button 2
Draws a box highlight.
Button 3
Places a spotlight on the screen.
Button 4
Draws a horizontal or vertical bar.
Button 5
Erases highlighting effects.
Enter
Use the Enter button for EasyMP, to navigate the menus,
(pointer button) or to use the remote as a mouse pointer when the
projector is connected to a computer with the mouse
cable. The Enter button acts as a mouse left-click.
Esc
Esc
R/C ON/OFF
Open the cover just below the Esc button to access these
remote control functions:
Illumination
Illuminates all buttons on the remote control.
Esc
Stops the current function. Pressing Esc while presenting
an EasyMP scenario or viewing a menu displays the
previous slide or menu. When the image source is
Computer, the Esc button acts as a mouse right-click.
Menu
Displays or hides the menu.
Comp
Switches to Computer image.
S-Video
Switches to S-Video image.
Auto
Optimizes the computer image.
P in P
Displays a video or S-video image in a subscreen on the
main display. Use the Enter button to reposition the
Picture in Picture (P in P) screen, or the E-Zoom button to
enlarge or reduce the image. Changes made to the P in P
screen location and size are automatically carried over to
the next P in P session.
Help
Displays the online help menu.
Power
Freeze
A/V Mute
R/C ON
OFF
E-Zoom
3
4
2
1
5
Enter
EasyMP
Displays the EasyMP main screen.
Video
Switches to Video image.
Resize
Switches the display dot mode and resize mode for VGA,
UXGA, SVGA, and SXGA input. Switches the aspect ratio
between 4:3 and 16:9 when video images are being
projected.
– Volume +
Adjusts the volume.
Esc
Menu
Help
Comp
EasyMP
S-Video
Video
Auto
Resize
Help
Comp
S-video
Auto
Picture in picture
Menu
EasyMP
Note: The projector might not respond to remote control
commands in these conditions: the R/C (remote control) ON/OFF
switch is in the OFF position; batteries are weak; ambient light is
too bright; a certain type of fluorescent light is present; a strong
light source (such as direct sunlight) shines into the infrared
receiver; or other equipment emitting infrared energy is present
(such as a radiant room heater). Correct these conditions to use
the remote control.
Video
Resize
P in P
- Volume +
Volume
1/01
EPSON PowerLite 505c/715c Projector - 7
EPSON PowerLite 505c/715c Projector
Caution: Press the button carefully to avoid breaking it. Make
sure the button is pressed in before you store the projector in a
carrying case or box.
Using EasyMP
The projector’s EasyMP feature lets you give a presentation
without a computer. You start by converting a Microsoft®
PowerPoint® file into a format called a scenario and
downloading the scenario to the projector’s memory card. See
the User’s Guide for instructions.
3. Press the button to insert it in the slot.
4. Insert the card in your computer’s PCMCIA slot or card
reader. See your computer documentation if you need
instructions.
5. Create your scenario and save it on the memory card,
following the instructions in the User’s Guide.
Once the scenario is saved on the memory card in the
projector, you can run it automatically or with the remote
control. You can also rearrange your slides and show images
captured from videos or other sources.
6. See your computer’s documentation if you need instructions
on removing the card from your computer. If you’re using
Windows 2000 or Me, you first need to click an icon to stop
or disconnect the card.
Accessing the Memory Card
To access the memory card, you can either transfer it to your
computer or use a USB cable to access the card in the
projector. (USB access available with Windows 98/Me/2000
only.)
7. Make sure the button below the memory card slot is pressed
in. Then insert the memory card (and adapter) in the
projector as shown. Make sure the card faces the back of the
projector.
If your computer has a PCMCIA slot or PC card reader, you
can insert the projector’s memory card in your computer to
transfer your scenario. First you need to remove it from the
projector. Make sure a scenario is not playing and the card is
not in use (the access light is off) before you remove it.
1. Press the button below the card slot.
Using the Buttons
Power
Source
Help
Keysto
ne
The button pops out.
2. Press the button again. The memory card is released, and
you can remove it from the slot in the projector.
Enter
Select
The following table summarizes the functions of the buttons
on top of the projector:
Button
8 - EPSON PowerLite 505c/715c Projector
1/01
Function
Power
Starts or stops projection.
Help
Displays the online help menu.
Source
Switches between Computer, Video, and S-video
sources.
Enter
Selects a menu option when the Help menu is
displayed.
– Keystone +
Adjusts a trapezoid distorted image to normal,
correction up to a ±15° tilt.
Select
Scrolls through options when the Help menu is
displayed.
EPSON PowerLite 505c/715c Projector
3. To clean the filter, EPSON recommends using a small
vacuum cleaner designed for computers and other office
equipment. If you don’t have one, gently clean the filter
using a very soft brush (such as an artist’s camel-hair brush).
Cleaning the Lens
Warning: Before you clean any part of the projector, turn off the
projector and unplug the power cord. Never open any cover on the
projector, except the lamp and filter covers. Dangerous electrical
voltages in the projector can injure you severely. Do not try to
service this product yourself, except as specifically explained in this
Product Information Guide. Refer all other servicing to
qualified service personnel.
Clean the lens whenever you notice dirt or dust on the surface.
Use a canister of compressed air to remove dust. To remove
dirt or smears on the lens, use lens-cleaning paper. If
necessary, moisten a soft cloth with lens cleaner and gently
wipe the lens surface.
Cleaning the Projector
If the dirt is difficult to remove or if the filter is torn, replace
it. Contact your dealer or call EPSON at (800) 873-7766 in
the United States and Canada to obtain a new one.
To clean the projector, first unplug the power cord. To
remove dirt or dust, wipe the projector with a soft, dry, lintfree cloth. To remove stubborn dirt or stains, moisten a soft
cloth with water and a neutral detergent. Then wipe the
projector.
Note: When you get a replacement lamp for your projector, a
new air filter is included. You should replace the filter when
you replace the lamp.
4. If you need to replace the filter, use a small screwdriver to
pry it off.
Do not use wax, alcohol, benzene, thinner, or other chemical
detergents. These can cause the projector’s plastic case to
warp.
Cleaning the Air Filter
Clean the air filter after every 100 hours of use, or if the
temperature warning light on top of the projector turns
red.
If the filter is not cleaned periodically, it can become clogged
with dust, preventing proper ventilation. This can cause
overheating and damage the projector. Follow these steps to
clean the filter:
1. Turn off the projector and unplug the power cord.
5. To install the new filter, first insert the tab, then press down
until it clicks in place.
2. Stand the projector on end to keep dust and dirt from falling
inside.
1/01
EPSON PowerLite 505c/715c Projector - 9
EPSON PowerLite 505c/715c Projector
6. Lift up the wire handle, as shown, and pull the lamp straight
out.
Replacing the Lamp
The projection lamp typically lasts for about 1000 hours of
use. It is time to replace the lamp when you see the following:
❏ The projected image gets darker or starts to deteriorate.
handle
❏ The
lamp warning light on top of the projector is red,
flashing red, or orange.
❏ The message LAMP REPLACE appears on the screen when
the lamp comes on (after about 900 hours of use). To
maintain projector brightness and image quality, replace the
lamp as soon as possible.
Warning: Let the lamp cool before replacing it. Also, do not touch
the glass portion of the lamp assembly. Touching the glass portion
of the lamp will result in premature lamp failure.
7. Gently insert the new lamp.
Contact your dealer or call EPSON at (800) 873-7766 in the
United States and Canada for a replacement lamp. Request
part number ELPLP14.
8. Once the lamp is fully inserted, tighten its screws.
Follow these steps to replace the lamp:
1. Turn off the projector, then unplug the power cord.
2. Allow the projector to cool down for at least half an hour (if
it has been on).
Warning: If the lamp breaks, handle the shards carefully to
avoid injury.
3. Turn the projector upside-down to access the lamp
compartment.
4. Use a screwdriver to loosen the retaining screw on the lamp
cover. (You can’t remove the screw from the cover.)
When the screw is loose, lift off the lamp cover.
9. Replace the lamp cover and tighten its screw securely. (The
projector won’t come on if the lamp cover is loose.)
)
5. Use a screwdriver to loosen the two screws holding the lamp
in place. (You can’t remove these screws.)
10 - EPSON PowerLite 505c/715c Projector
1/01
EPSON PowerLite 505c/715c Projector
Optional Accessories
Product
Product
number
Replacement lamp and air filter
ELPLP14
Soft carrying cases:
Samsonite® wheeled soft case
Slimline soft shoulder bag
Notebook/projector soft shoulder bag
ATA molded hard shell case
ELPKS35
ELPKS31
ELPKS32
ELPKS30
Ceiling mount
ELPMB34
Suspension adapter for ceiling mount (1-inch pipe)
ELPMBAPS
Suspension adapter for ceiling mount (1.5-inch pipe)
ELPMBAST
®
Kensington MicroSaver security lock
ELPSL01
Portable projection screens:
50-inch screen
60-inch Insta-Theatre screen
80-inch Insta-Theatre screen
ELPSC06
ELPSC07
ELPSC08
Wireless microphone and two satellite speakers
ELPCVS1
Presentation audio system
ELPPAS1
Macintosh® adapter set (includes monitor adapter
and desktop adapter)
ELPAP01
VGA to 13W3 video cable (for connecting to certain
high-end workstations)
ELPKC06
Component video cable (D-sub 15-pin to 3BNC)
ELPKC19
You can purchase these accessories from your dealer or by
calling EPSON at (800) 873-7766; or visit the EPSON
Store™ at www.epson.com (U.S. sales only). In Canada, please
call (800) 873-7766 for dealer referral.
Related Documentation
CPD-11736
EPSON PowerLite 505c/715c
User’s Guide
CPD-11737
EPSON PowerLite 505c/715c
Quick Setup sheet
Service Manual
TM-505c/715c
Parts Price Lists
PL-EMP505c, PL-EMP715c
1/01
EPSON PowerLite 505c/715c Projector - 11
EPSON PowerLite 505c/715c Projector
12 - EPSON PowerLite 505c/715c Projector
1/01