S2000-IK Rev.04 Instruction Manual (English )

S2000-IK Rev.04 Instruction Manual (English )
S2000-IK Rev.04
Addressable Curtain PIR Motion Detector
INSTRUCTION MANUAL
GENERAL
S2000-IK Revision 04 Addressable Curtain Passive Infrared (PIR) Motion Detector (hereinafter referred to as the
detector) is designed to be used indoors. It detects intrusion into protected areas and sends an alarm message to the
connected S2000-KDL controller via the two-wire multiplex addressable polling loop.
The S2000-IK rev.04 has a two-dimensional coverage pattern (“vertical curtain”).
The detector provides increased immunity against lighting and radio frequency interference.
KEY FEATURES
Dual-element pyro-electric infrared sensor
High-density coverage offering high probability of detecting an intruder
Protected against insects entering to the pyro-electric infrared sensors
Arranging sabotage-resistant zones just beneath the detector prevents unauthorized access to the detector.
Digital signal processing
Powered via the multiplex addressable polling loop of the S2000-KDL
Supports DPLS_v2.xx protocol
SPECIFICATIONS
Detection Range
Coverage Pattern
Input Voltage (from a S2000-KDL)
Current Consumption (via the loop of the S2000-KDL)
Horizontal Angle of Sight
Operating Temperatures
Humidity
Overall Dimensions (H x W x D)
Weight
Mounting Height
10 m
Curtain (two-dimensional)
8 ÷ 10 VDC
0.5 mA max when indication is off
6°
−30 to +50°C
95% at 25°C, non-condensing
105 mm × 75 mm × 56 mm max
0.1 kg max
2.3 meters
MOUNTING LOCATION CONSIDERATIONS
The detector is intended to be used indoors. Considering a
location to mount the detector, please take into account that
the detection zone must not be obscured by any nontransparent objects such as curtains, houseplants, cabinets,
room dividers, etc. as well as by glass or mesh partitions.
Do not locate the detector where it can be exposed to false
alarm sources such as windows, air conditioners, heaters,
radiators, etc.
Wires of the multiplex addressable polling loop should be
located away from high-voltage electric cables.
The detector allows wall or corner mounting at a height of
2.3 m above the floor. This provides the detection range at
least 10 meters. The detection pattern is shown in Figure 1.
Figure 1: S2000-IK Rev.04 Detection Pattern
INSTALLING THE DETECTOR
1. Using a screwdriver remove the cover screw at the bottom of the
detector (see Figure 2) and separate the detector cover.
2. Using a screwdriver remove the PCB screw (see Figure 2) and lift
the PCB out of the detector base.
3. Drill out the required mount and wiring holes in the base (see
Figure 2).
4. Having selected the mounting location, mark the positions of the
fixing holes taking into account mounting holes in the base, and drill
holes at the marked places
5. Slide the wire into the wire holes leaving some centimeters for
connecting wires to the terminal blocks
6. Finally, replace the PCB and tighten the PCB screw
Figure 2: Detector Base
WIRING
Figure 3a shows the way to connect detector’s PL
contacts which are situated at the top of its PCB
to the relevant contacts of the S2000-KDL.
Figure 3b shows the wiring diagram for
connecting the detector to the multiplex
addressable loop of the S2000-KDL controller
which is in turns connected to the network
controller and the power supply.
S2000-KDL
S2000(M)
S2000-IK
3 RS-485A
1
A
4 RS-485B
2
B
1
+12 V
2
GND
1
+PL
5
+PL
2
−PL
6
−PL
1
GND
2
+U
Power Supply
a) Connection Terminals
1
+12 V
2
GND
b) Detector’s Wiring Diagram
Figure 3 Connecting the Detector
PROGRAMMING
The S2000-IK rev.04 to operate properly within two-wire addressable polling loop of the S2000-KDL controller, it must be
assigned to a unique number 1 to 127 within the loop – the address which is stored in the S2000-IK rev.04 non-volatile
memory (EEPROM). This address provides identifying the detector by the S2000-KDL controller. Moreover, the
monitoring strategy must be defined which will be used by the S2000-KDL controller while processing signals received
from the S2000-IK rev.04.
Programming the S2000-IK Rev.04 Address within the S2000-KDL Addressable Loop
An S2000-IK rev.04 is supplied with the default address of 127. This address value can be changed using either
S2000(M) console tools or PC tools such as UProg Configuration Tool.
In order to program the unique S2000-IK rev.04 loop address, connect it to a S2000-KDL controller which is in turns
connected to a network controller (an S2000(M) console or PC under UProg software). Then send one of the following
commands to the S2000-KDL controller (for getting more information see the relevant User’s Manual):
Change the Device Address
Use the Change Device Address command specifying the old detector address and the
new detector address as the parameters (see more information in the referred
Manuals). The network controller will display the messages about disconnecting the
device with the old address and then detecting the device with newly programmed
address.
Program the Device Address
If the device address is unknown or two devices have the same address then use the
Program Device Address command specifying a required address as the parameter.
Then remove the detector cover and ensure the LED is flashing indicating the
programming mode (frequent short flashes every 2 s). Next, press the tamper switch in
LLLS pattern, where L stands for long pressings (longer than 0.5 s) while S stands for
short pressings (shorter than 0.5 s), pauses between pressings not exceeding 1s each.
If the address has changed successfully, the LED will be lit steady and a message
about detecting the device with the newly assigned address shall be displayed by a
network controller (S2000(M) or UProg Configuration Tool). If you failed to assign the
address, wait for 2 s and repeat programming.
Programming the S2000-KDL to Operate the S2000-IK Rev.04
To handle signals from an S2000-IK rev.04 correctly, the S2000-KDL controller which the detector is connected to must
be programmed with the Zone Type parameter for this S2000-IK rev.04 being set to value 4 (Intrusion), or 5 (Intrusion
with Tamper Check), or 7 (Entrance), or 11 (Panic), or 6 (Auxiliary). To program the S2000-KDL, connect it to a PC under
UProg Configuration Tool and follow the relevant programming instructions in accordance with the S2000-KDL User’s
Manual.
WALK TEST
Connect the detector to the multiplex addressable polling loop as shown in Figure 3b. Then power on the controller and
wait for about two minutes. Next, walk through the detection zone. The detector shall issue an alarm after your three or
four steps, with its LED being flashing. Wait until the LED finishes flashing, and then continue crossing the detection
zone. The detector should issue an alarm. If nobody is moving within the detection zone, no alarms shall be issued.
WARNING
To ensure proper operation, walk test the S2000-IK rev.04 annually as described above.
ENABLING/DISABLING LED INDICATION
LED indication can be controlled either via a PC or by means of the detector tamper switch.
If LED indication is to be controlled via a PC, by the connected S2000-KDL, the S2000-KDL should be specifically
configured from the PC using the UProg Configuration Tool. The parameter Device Indication Control of the S2000-KDL
polling loop input zone which is assigned to the S2000-IK rev.04 should be set to a proper value. By default, Device
Indication Control is set to the value of 1, providing LED indication in accordance with the detector’s own pre-determined
algorithm. To disable indication, set this parameter to zero.
If LED indication is to be controlled by the tamper switch, the algorithm is as follows. On detector’s switching on the LED
indication is enabled (unless the input S2000-KDL zone assigned to the detector is configured with disabled indication).
To disable indication, press the tamper switch in LLSL pattern; otherwise, to enable indication, press the tamper switch in
LLSS pattern, where L stands for a long pressing (longer than 0.5 s) while S stands for a short pressing (shorter than
0.5 s). Pauses between pressings must not exceed 1 s each.
ZAO NVP Bolid, 4 Pionerskaya Str., Korolev 141070, Moscow Region, Russia
Phone/fax: +7 495 775-7155
Email: [email protected], [email protected]
www.bolid.com
BOLID ONE YEAR LIMITED WARRANTY
Bolid Company and its divisions and subsidiaries («Seller»), 4 Pionerskaya Str., Korolev 141070, Moscow Region, Russia warrants its
security equipment (the «product») to be free from defects in materials and workmanship for one year from date of original purchase,
under normal use and service. Seller’s obligation is limited to repairing or replacing, at its option, free of charge for parts or labor, any
product proven to be defective in materials or workmanship under normal use and service. Seller is not responsible for results where
the product is used improperly, where it is used for any application it is not intended for, used under unacceptable environmental
conditions and mishandled or stored under improperly. Seller shall have no obligation under this warranty or otherwise if the product is
altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who
installed and maintains your security equipment or the Seller for product repair.
This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. There are no express warranties,
which extend beyond the face hereof. Any implied warranties, obligations or liabilities made by seller in connection with this product,
including any implied warranty of merchantability, or fitness for a particular purpose or otherwise, are limited in duration to a period of
one year from the date of original purchase. Any action for breach of any warranty, including but not limited to any implied warranty of
merchantability, must be brought within 12 months from date of original purchase. In no case shall seller be liable to anyone for any
consequential or incidental damages for breach of this or any other warranty, express or implied, or upon any other basis of liability
whatsoever, even if the loss or damage is caused by the seller’s own negligence or fault. Some countries do not allow limitation on how
long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal injury
or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection.
Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events
occurring without providing an alarm, but it is not insurance or guarantee that such will not occur or that there will be no personal injury
or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD
LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE
PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This
warranty gives you specific legal rights, and you may also have other rights which vary from country to country. No increase or
alteration, written or verbal, to this warranty is authorized.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement