American Standard Serin Single Hole 1-Handle Mid-Arc Vessel Bathroom Faucet with Grid Drain in Chrome Installation instructions

Minimalist

VESSEL LAVATORY FITTING

Installation

Instructions

2064 Series

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

M 9 6 8 8 5 8 R e v. 1 . 5

Recommended Tools

Regular Screwdriver

Adjustable Wrench

Plumbers' Putty or Caulking Channel Locks

Phillips Screwdriver

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

1

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

INSTALL LAVATORY FAUCET

CAUTION

Turn off hot and cold water supplies before beginning.

Seat SEAL (1) into under side of ESCUTCHEON RING (2).

Seat ESCUTCHEON RING (2) with collar facing up into groove in faucet base.

Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through

ESCUTCHEON RING (2) and hole in mounting surface.

From below, install SUPPORT PLATE (7) GASKET (5) and MOUNTING

NUT (6) onto SHANK (4). Secure Faucet with MOUNTING NUT (6).

Before final tightening, adjust Faucet so that it is centered. Tighten

MOUNTING NUT (7) to complete mounting.

Note: For thick deck installations, the SUPPORT PLATE (7) can be omitted.

GROOVE

(FAUCET BASE)

COLLAR

2

1

4

MOUNTING SURFACE

7

5

6

3

2

MAKE WATER SUPPLY CONNECTIONS

Turn off hot and cold water supplies before beginning.

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot and right supply to the Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.

Faucet supplies are 10" long from faucet base.

Note: If additional supply length is required, installer must purchase additional parts separately.

Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.

Figure A.

10"

HOT

2

COLD

1

LOOP SUPPLIES

IF REQUIRED

HOT

Figure A.

COLD

M 9 6 8 8 5 8 R e v. 1 . 5

4 TEST INSTALLED FAUCET

AND CHECK FOR LEAKS

With HANDLE (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate HANDLE (1) to flush water lines thoroughly.

Replace AERATOR (3).

3

1

HOT

OFF

COLD

ON

HOT

COLD

5

SERVICE CAUTION

Turn off hot and cold water supplies before beginning.

To remove or replace cartridge

Turn valve to OFF position.

Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).

Pull off HANDLE (3) and CAP (4).

Unthread CARTRIDGE NUT (5) and remove.

Pull out CARTRIDGE (6).

Inspect CARTRIDGE (6) and O-RINGS (7) for debris and clean if necessary.

Clean MANIFOLD (8) and rinse clean.

Reinstall CARTRIDGE (6) and O-RINGS (7) onto MANIFOLD (8).

Reinstall CARTRIDGE NUT (5), CAP and HANDLE ASSEMBLY.

If spout drips, operate handle several times from OFF to ON and HOT to COLD position. Do not force - handles turn only 90˚.

2

1

REMOVE

2

2.5mm HEX KEY

3

INSTALL

4

5

6

7

8

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON

FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS,

OR A CLOTH WITH A COARSE SURFACE.

M 9 6 8 8 5 8 R e v. 1 . 5