Zanussi ZCM641 Specifications

MIXED FUEL
COOKER
ZCM 640
ZCM 641
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need assistance,
contact our Customer Care Department on 08705 727727
Installation
•
•
•
•
•
•
This appliance must be installed and serviced by a
competent person as stated in the Gas Safety (
Installation and Use) Regulations Current Editions
and the IEE Wiring Regulations.
For appliances installed in the Republic of Ireland
please refer to NSAI-Domestic Gas Installations
I.S.813 Current Editions and the ETCI Rules for
Electrical Installations.
This cooker is heavy. Take care when moving it.
Remove all packaging before using the cooker.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Do not attempt to modify the cooker in any way.
Child Safety
•
•
•
This cooker is designed to be operated by adults.
Do not allow children to play near or with the cooker.
The cooker gets hot when it is in use. Children should
be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the cooker.
During Use
•
•
•
•
•
•
•
2
This cooker is intended for domestic cooking only.
It is not designed for commercial or industrial
purposes.
When in use a gas cooker will produce heat and
moisture in the room in which it has been installed.
Ensure there is a continuous air supply, keeping air
vents in good condition or installing a cooker hood
with a venting hose.
When using the cooker for a long period of time,
the ventilation should be improved, by opening a
window or increasing the extractor speed.
Do not use this cooker if it is in contact with water.
Do not operate the cooker with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
During use the appliance becomes hot. Care should
be taken to avoid touching heating elements inside
the oven.
When using other electrical appliances, ensure the
cable does not come into contact with the hot
surfaces of the cooker.
•
•
•
•
•
•
Unstable or misshapen pans should not be used on
the hob burners as unstable pans can cause an
accident by tipping or spillage.
Never leave the cooker unattended when cooking
with oil and fats.
This cooker should be kept clean at all times. A
build-up of fats or foodstuffs could result in a fire.
Never use plastic dishes in the oven or on the hob
burners. Never line any part of the oven with
aluminium foil.
Always ensure that the oven vent which is located
at the centre back of the hob is left unobstructed to
ensure ventilation of the oven cavity.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above
the cooker.
Service
•
This cooker should only be repaired or serviced by
an authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
•
•
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it
unusable, by cutting off the cable.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
This appliance is manufactured according to
the following EEC directives:
73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC,
current edition.
These instructions are only valid in the
countries whose symbols appear on this
booklet's cover.
Contents
For the User
For the Installer
Important Safety Information
2
Guarantee Conditions
14
Control Panel
3
Instructions for the Installer
15
The Oven Cavity
4
Important Safety Requirements
15
The Gas Hob Controls
4
Installation
16
Electric Oven
5
Electrical Connections
18
The Minute Minder
5
Commissioning
19
Before the First Use of the Cooker
6
Conversion from Natural Gas to LPG
19
Using the Oven
6
Using the Fan Oven
7
Hints and Tips
8
Defrosting
9
Guide to Use the Instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Grilling
10
Maintenance and Cleaning
11
Safety Instructions
Cleaning the Oven
12
Step by step instructions for an operation
Something not Working
13
Service and Spare Parts
13
Customer Care Department
14
Hints and Tips
Environmental Information
Control Panel
9
1
1.
2.
3.
4.
5.
2
3
4
Electric ignition push button
Back left burner control knob (semi-rapid)
Front left burner control knob (rapid)
Front right burner control knob (auxiliary)
Back right burner control knob (semi-rapid)
5
6
7
8
10
6. Oven function control knob
7. Oven thermostat control knob
8. Minute Minder
9. Mains Pilot Light
10. Oven Thermostat Pilot Light
3
The Oven Cavity
Grill element
Oven Light
Accessories
Grill/roasting pan
Grill trivet
Removable
handles
Oven fan
2 anti-tip
shelves
The Gas Hob Controls
•
•
•
•
To light a burner:
Push the electric ignition button which is marked
with a little spark ( ).
At the same time, push in and turn the relevant control
knob anticlockwise to maximum position.
Then adjust the flame as required.
If the burner does not ignite, turn the control knob to
zero, and try again.
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the pan, causing the handle to
overheat.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
4
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
Large (rapid)
Medium (semi-rapid)
Small (Auxiliary)
minimum
diameter
maximum
diameter
180 mm.
120 mm.
80 mm.
260 mm.
220 mm.
160 mm.
Electric Oven
Oven Function Control Knob
Oven Light - The oven light will be on without any
cooking function
Defrost Setting - This setting is intended to assist in
thawing of frozen food .
Fan cooking - This allows you to roast or roast and
bake simultaneously using any shelf, without flavour
transference.
Grill - The heat comes only from the top element.
Thermostat Control Knob
Turn the thermostat control knob clockwise to select
temperatures between 50°C and about 230°C (max).
Mains On Light
The mains on light will come on when any function is
selected.
Thermostat Control Light
The thermostat control light will come on when the
thermostat control knob is turned. The light will remain
on until the correct temperature is reached. It will then
cycle on and off to show the temperature is being
maintained.
The Minute Minder
The minute minder will mark the end of a timed period
with an acoustic alarm. The maximum timing is 60
minutes.
Turn the Minute Minder knob clockwise to the maximum
time position, then turn it back to the required time.
The Minute minder will not affect in any way the oven
operation, if it is in use.
5
Before the First Use of the Cooker
INSTALLATION
Any gas installation must be carried out by a
qualified gas installer or competent person, and
in accordance with existing rules and regulations.
The relevant instructions are to be found in the second
section of this manual.
Please ensure that when the appliance is installed, it is
easily accessible for the engineer in the event of a
breakdown.
WHEN THE COOKER IS FIRST INSTALLED
Once the cooker has been installed, it is important
to remove any protective materials, which were
put on in the factory.
Remove all packaging, both inside and outside
the oven, before using the oven.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
1. Switch the oven function control knob to fan
cooking
.
2. Set the thermostat control knob to MAX.
3. Open a window for ventilation.
4. Allow the oven to run empty for approximately 45
minutes.
This procedure should be repeated with the grill
function for approximately 5-10 minutes.
Using the Oven
4
Always cook with the oven door closed.
Stand clear when opening the drop down
oven door. Do not allow it to fall open support the door using the door handle, until
it is fully open.
The oven has four shelf levels, and is supplied
with two shelves.
The shelf positions are counted from the bottom
of the oven as shown in the diagram.
It is important that these shelves are correctly
positioned as shown in the diagram.
•Do not place cookware directly on the oven
base.
3
2
1
Hints and Tips
Condensation and Steam
Storage Drawer
When food is heated it produces steam in the same
way as a boiling kettle. The oven vents allow some of
this steam to escape. However, always stand back
from the oven when opening the oven door to allow
any build up of steam or heat to release.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense
and produce water droplets. This is quite normal and is
not a fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
The storage drawer is located underneath the oven
cavity.
6
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
therefore flammable materials such as oven
gloves, tea towels, plastic aprons etc. should not
be stored in the drawer.
Oven accessories such as baking sheets, will
also become hot, therefore care should be taken
when removing these items from the drawer
whilst the oven is in use or still hot.
Using the Fan Oven
The air inside the oven is heated by the element around
the fan situated behind the back panel. The fan circulates
hot air to maintain an even temperature inside the oven.
The advantages of cooking with this function are:
•
Even Heating for Baking
The fan oven has uniform heating on all shelf
positions. This means that batches of the same
food can be cooked in the oven at the same time.
However, the top shelf may brown slightly quicker
than the lower one. This is quite usual. There is no
mixing of flavours between dishes.
Faster Preheating
As the fan oven quickly reaches temperature, it is
not usually necessary to preheat the oven although
you may find that you need to allow an extra 5-7
minutes on cooking times. For recipes which
require higher temperatures, best results are
achieved if the oven is preheated first, e.g. bread,
pastries, scones, souffles, etc.
•
•
How to Use the Fan Oven
1. Turn the oven function control knob to
.
2. Turn the thermostat control to the required
temperature.
Lower Temperatures
Fan oven cooking generally requires lower
temperatures than conventional cooking.
Follow the temperatures recommended in the
cooking chart. Remember to reduce temperatures by
about 20-25°C for your own recipes which use
conventional cooking.
THINGS TO NOTE
• The oven light will come on when the oven function
control knob is set.
•
The thermostat control light will remain on until the
correct temperature is reached. It will then cycle on
and off to show that the temperature is being
maintained.
Cooking Chart
This chart is intended as a guide only. It may be necessary to increase or decrease the temperature to suit your
individual requirements. Only experience will enable you to determine the correct setting for your personal requirements.
Food
Position
Shelf
Biscuits
Bread
Casseroles
Cakes:
- Small and queen
- Sponges
- Madeira
- Rich Fruit
- Christmas
- Meringues
Fish
Fruit Pies and Crumbles
Milk Puddings
Pastry:
- Choux
- Shortcrust
- Flaky
- Puff
Plate Tarts
Quiches/Flans
Scones
Roasting:
Meat & Poultry
}
Cooking
Cooking
Temp (°C) Time (minutes)
180 - 190
210 - 220
130 - 140
160-170
160 - 170
Shelf positions 140 - 150
are not critical 130 - 140
but ensure that 130 - 140
oven shelves
90 - 100
are evenly
170 - 190
spaced when
190 - 200
more than one
130 - 140
is used.
10 - 20
25 - 30
2½ - 3 h.
18 - 25
18 - 20
1¼ - 1½ h.
2¼ - 2½ h.
3 - 4½ h.
2½ - 3 h.
20 - 30
40 - 50
1½ - 2 h.
190 - 200
190 - 200
190 - 200
210 - 220
180
180 - 210
210 - 220
30 - 35
15 - 20
25 - 40
25 - 40
25 - 45
25 - 45
8 - 10
160 - 180
see roasting
chart
7
Roasting Chart
Meat
Cooking Time
When roasting, ensure the meat is
cooked thoroughly, use a meat
thermometer if preferred to check the
centre temperature has reached the
required temperature (see table
below).
Beef
20-35 mins per 1/2kg (lb) + 20-35 mins
Beef, boned
25-35 mins per 1/2kg (lb) + 25-35 mins
Mutton and Lamb
25-35 mins per 1/2kg (lb) + 25-35 mins
MEAT
TEMPERATURES
Pork and Veal
30-40 mins per 1/2kg (lb) + 30-40 mins
Beef
Ham
30-40 mins per 1/2kg (lb) + 30-40 mins
Chicken
15-20 mins per 1/2kg (lb) + 20 mins
Rare - 60°C
Medium - 70°C
Well Done - 80°C
Turkey and Goose
15-20 mins per 1/2kg (lb) up to 3.5kg (7lb)
Pork
Well Done - 80°C
+ 15 mins per 1/2kg over 3.5kg (7lb)
Lamb
Medium - 70°C
Well Done - 80°C
Duck
25-35 mins per 1/2kg (lb) + 20 mins
Hints and Tips
Shelf positions are not critical, but make sure the shelves
are evenly spread.
When cooking more than one dish in the fan oven, place
dishes centrally on the shelves rather than several dishes
on one shelf.
When the oven is full, you may need to allow slightly
longer cooking time.
A shelf may be placed on the floor of the oven. Place
dishes on a shelf in this position rather than on the oven
base, to allow air circulation around the food.
When the oven is full of the same food, e.g. equal trays
of small cakes or equal size victoria sandwich cakes,
then they will be cooked in the same time and removed
from the oven together. When different sizes of trays or
types of food, e.g. biscuits and cakes are cooked, they
will not necessarily be ready together.
The fan oven can be used to heat foods through without
thawing first, e.g. fruit tarts, mince pies, sausage rolls,
and other small pastry items. Use a temperature of 190200°C and allow 20-40 minutes (depending on the quantity
of food in the oven).
The use of too high temperatures can cause uneven
browning. Check with the recommendations for oven
temperatures given in the cooking charts, but be prepared
to adjust the temperature by 10°C if necessary.
Remember to reduce temperatures by about 20-25°C for
your own conventional recipes.
When roasting do use the trivet in the meat tin. Fat and
meat juices will drain into the meat tin below and can be
used to make gravy. The trivet also prevents splashes of
fat from soiling the oven interior.
The meat tin should not be placed on a heated hotplate
or burner as this may cause the enamel to crack.
Defrosting
The oven fan operates without heat and circulates the
air, at room temperature, inside the oven. This increases
the speed of defrosting. However, please note that the
temperature of the kitchen will influence the speed of
defrosting.
This function is particularly suitable for delicate food which
could be damaged by heat, e.g. cream filled gateaux,
iced cakes, pastries, bread and other yeast products.
How to Use Defrosting
1. Turn the oven function control knob to
Hints and Tips
•
•
•
•
.
2. Ensure the thermostat control knob is in the OFF
position.
Cover food with a lid, aluminium foil or plastic film to
prevent drying out during defrosting.
ALWAYS COOK THOROUGHLY IMMEDIATELY
AFTER THAWING.
Frozen food should be placed in a single layer when
ever possible and turned over half way through the
defrosting process.
Only joints of meat and poultry up to 2 kg. (4 lb.) are
suitable for defrosting in this way.
Refer to the following table for approximate defrosting
times.
Defrosting time
(Mins)
Standing time
(Mins)
Chicken 1000 g.
100-140
20-30
Place the chicken on an inverted saucer on a large
plate. Defrost open and turn at half time or defrost
covered with foil. Remove giblets as soon as possible.
Meat 1000 g.
100-140
20-30
Defrost open and turn at half time or cover with foil
Meat 500 g.
90-120
20-30
As above
Trout 150 g.
23-35
10-15
Defrost open
Strawberries 300 g.
30-40
10-20
Defrost open
Butter 250 g.
30-40
10-15
Defrost open
Cream 2 x 200 g.
80-100
10-15
Defrost open (cream is easy to whip even if parts of
it are still slightly frozen)
60
60
Food
Cake 1400 g.
Notes
Defrost open
The times quoted in the chart should be used as a guide only, as the speed of defrosting will depend on the kitchen
temperature. For example, the colder the ambient temperature, the longer the defrosting time.
Grilling
Grilling must be carried out with the oven
door closed. The grill pan handles must be
removed from the pan.
How to Use the Grill
1. Turn the oven control function knob to
.
2. Turn the thermostat control knob on the required
temperature.
3. Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food
close to the element for faster cooking and further
away for more gentle cooking.
Preheat the grill on a full setting for a few minutes
before sealing steaks or toasting. Adjust the heat setting
and the shelf as necessary, during cooking.
Cooking chart
Cooking time depends on the thickness of the meat and
not on its weight.
Type of food
Bacon rashers
Chicken joints
Gammon rashers
Lamb chops
Pork chops
Sausages (turning as required)
Steaks (average thickness)
Toast
The grill element is controlled by the thermostat.
During cooking, the grill cycles on and off to
prevent overheating.
Hints and Tips
-
-
-
10
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air and to lift
the food out of the fats and juices. Food such as
fish, liver and kidneys may be placed directly on
the grill pan, if preferred
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish lightly
with a little oil or melted butter to keep them moist
during cooking
Accompaniments such as tomatoes and mushrooms
may be placed underneath the grid when grilling
meats
When toasting bread, we suggest that the top runner
position is used.
The food should be turned over during cooking, as
required.
OI L
Mins per side
2-5
15 - 20
5-8
6 - 12
10 - 15
10 - 12
Rare
3-6
Medium
6 - 10
Well done 8 - 12
1 - 11/2
Maintenance and Cleaning
Before any maintenance or cleaning can be
carried out, you must DISCONNECT the cooker
from the electricity supply.
This appliance cannot be cleaned with steam or
with a steam cleaning machine.
The Hob Top
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little wasing up liquid
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Pan Supports
The pan supports are dishwasher proof. If washing them
by hand, take care when drying them as the enamelling
process occasionally leaves rough edges. If necessay,
remove stubborn stains using a paste cleaner.
The pan support of this cooker is fitted with anti-scratch
rubber feet.
These feet are dishwasher proof and should not be
removed when cleaning the pan support.
If the rubber feet become detached from the pan support
re-fit as per diagram.
Anti-scratch rubber feet can be obtained from your local
Zanussi Service Force Centre.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy
water, and remove marks with a mild paste cleaner. A
well moistened soap impregnated steel wool pad can
be used with caution, if the marks are particularly difficult
to remove.
After cleaning, be sure to wipe dry with a soft cloth.
11
Cleaning the Oven
Before cleaning always allow the cooling fan to
cool the oven down before switching off at the
electricity supply.
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven,
check that they are suitable and that their use is
recommended by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives
should also be avoided.
External cleaning
Regularly wipe over the control panel, oven door and
door seal using a soft cloth well wrung out in warm
water to which a little washing up liquid has been added.
To prevent damaging or weakening the door
glass panels avoid the use of the following:
• Household detergent and bleaches
• Impregnated pads unsuitable for non-stick saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily
soiled it is recommended that a cleaning product such
as Hob Brite, or Bar Keepers Friend is used.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not
observed the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of
the panel shattering. Contact your local Service
Centre who will be pleased to advise further.
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
If the soilage has become set, after the oven has cooled
down, the following process will help to soften the
splatters to help make cleaning easier.
1. Place the grill/ meat pan on the oven shelf
positioned in the lowest runner.
2. Add a few drops of washing-up liquid to the
pan and fill to about 12 mm. with boiling water
from the kettle.
3. Close the oven door, turn the oven function
knob on fan oven
knob on 50°C.
4. After 15 minutes, turn off the thermostat and
allow the fan oven to continue without heat
for a further 5 minutes, when the temperature of the water will have cooled down.
5. Carefully remove the pan of water from the
oven and use normal oven cleaners to clean
away soil residues.
6. Leave a little of the soapy water to soak into
any burned on spillage on the floor of the oven
for a longer time if necessary.
Oven Shelves
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
Replacing the Oven Light
Disconnect the appliance from the electricity
supply.
If the oven bulb needs replacing, it must comply with
the following specifications: electric power, 15W;
electric rate, 230V (50 Hz); resistant to temperatures
of 300°C; connection type: E14. These bulbs are
available from your local Service Force Centre.
To replace the faulty bulb:
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace it with the new
one.
4. Refit the glass cover.
5. Reconnect to the electrical supply.
12
and set the thermostat
FO 0287
Something not working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SYMPTOM
There is no spark when lighting the gas
The gas ring burns unevenly
SOLUTION
Check that the unit is plugged in and the electrical
supply is switched on
Check that the RCCB has not tripped (if fitted)
Check the mains fuse has not blown
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
Check the main jet is not blocked and the burner
crown is clear of food particles.
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
The oven does not come on
The oven temperature light does not come on
The oven light does not come on
Check that both a cooking function and temperature
have been selected.
Check the oven is wired in properly, and the socket
switch or the switch from the mains supply to the
oven are ON.
Select a temperature with the thermostat control
knob
Select a function with the oven function control
knob.
Check the light bulb, and replace it if necessary
(see "Replacing the Oven Light")
It takes too long to finish the dishes, or they are
cooked too fast.
The temperature may need adjusting
Steam and condensation settle on the food and the
oven cavity.
Refer to the contents of this booklet, especially to
The oven fan is noisy
Check that shelves and bakeware are not
the chapter “Using the Oven”.
Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
vibrating in contact with the oven back panel.
Service and Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk
For Customer Service in the Republic of Ireland please
contact us at the address below:
Zanussi-Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090 751
Email: service.eid@electrolux.ie
13
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
Customer Care
Department
For general enquiries concerning your Zanussi
appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter
or telephone at the address below or visit our website
at www.zanussi.co.uk
Customer Care Department
Zanussi-Electrolux
Cornwall House
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Zanussi Guarantee Conditions
We, Zanussi, undertake that if, within 12 months of the
date of the purchase, this Zanussi appliance or any part
thereof is proved to be defective by any reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE for
labour, materials or carriage on condition that:
*
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
* All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside European Community (EC) or European Free
Trade Area.
14
*
*
Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
Products of Zanussi manufacture which are not
marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European Community
(EC) or European Free Trade Area.
* The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone
Stockholm
Slough
+33 (0) 3 44 62 29 29
+49 (0) 800 234 7378
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 1753 219897
Instructions for the Installer
Technical Data
Hob
Appliance Class 2 sub class 1 and Class 1
APPLIANCE CATEGORY:
II2H3+
APPLIANCE GAS SUPPLY:
Natural Gas 20 mbar
Rear left burner (semi-rapid)
Front left burner (rapid)
Rear right burner (semi-rapid)
Front right burner (auxiliary)
Dimensions
Height
Depth
Width
Oven Capacity
VALUE =
NATURAL
Hs 37.78 MJ/m 3
GAS
20 mbar Ws 50.72 MJ/ m3
SEMI-RAPID
(medium)
2000 W
1650 W
30 W
25 W
2055 W
230 V
AUXILIARY
(small)
POSITION
MAX
MIN
MAX
MIN
MAX
MIN
NOMINAL THERMAL
POWER kW
3.0
0.65
2.0
0.45
1.0
0.33
NOMINAL FLOW
RATE m3/h
0.286
0.062
0.190
0.043
0.095
0.031
119
Adjust.
96
Adjust.
70
Adjust.
NOMINAL THERMAL
POWER kW
2.8
0.65
2.0
0.45
1.0
0.33
NOMINAL FLOW
RATE g/h
202
47
144
32
72
24
86
40
71
32
50
28
NOZZLE REFERENCE
1/100 mm
LPG GAS
VALUE =
28-30/37 Hs 49.92 MJ/Kg
mbar
Ws 82.09 MJ/ m3
Convection Heating Element
Grill Element
Convection Fan
Oven light
Cooker rating (total)
Supply voltage (50 Hz)
RAPID
(large)
CHARACTERISTICS
NOZZLE REFERENCE
1/100 mm
kW
kW
kW
kW
Oven
900 mm
600 mm
600 mm
56 litres / 1.97 Cu. ft
BURNER
TYPE OF
GAS
2.0
3.0
2.0
1.0
Important Safety Requirements
This appliance must be installed in accordance with
the Gas Safety (Installation and Use) Regulations
(current addition) and the I.E.E. Wiring Regulations.
Detailed recommendations are contained in the
following British Standard Codes of Practice - B.S.
6172, B.S. 5440: Part 2 and B.S. 6891: Current Editions.
For appliances installed in the Republic of Ireland
please refer to NSAI- Domestic Gas Installation I.S.
813 Current Editions and the ETCI Rules for Electrical
Installations.
Provision for Ventilation
The room containing the cooker should have an air
supply in accordance with B.S. 5440: Part 2: Current
Editions.
The following requirements for ventilation must be met.
The cooker should not be installed in a bed sitting room
with a volume of less than 20m3, if it is installed in a
room of volume less 5m3 an air vent of effective area
of 110cm2 is required; if it is installed in a room of
volume between 5m3 and 10m3, an air vent of effective
area 50cm2 is required, while if the volume exceeds
11m3 no air vent is required. However, if the room has
a door which opens directly to the outside, no air vent
is required even when the volume is between 5m3 and
11m3.
If there are other fuel burning appliances in the same
room, B.S. 5440: Part. 2: Current Editions should be
consulted to determine the requisite air vent
requirements.
For appliances installed in the Republic of Ireland
please refer to the NSAI- Domestic Gas Installation I.S.
813 Current Editions Table Four.
15
Location of the appliance
This appliance must not be installed in a bed-sitting
room of volume less than 20m³ or in a bathroom, shower
room or garage. It is essential that the appliance is
positioned as stated below (see fig.1) i.e. shelves, wall
cabinets and cooker hoods must be fitted a minimum
of 787mm directly above the top of the hotplate and
400mm above the hotplate when fitted in line with the
outside of the appliance. If the units are intended to be
fitted adjacent to the appliance but less than 400mm
above the hotplate, then a minimum space of 100mm
must be maintained between the sides of the unit and
the appliance (see fig.). Curtains must not be fitted
immediately behind the appliance or within 150mm of
the sides of the hotplate. If fitted next to or between
two base units a minimum space of 1mm must be left
between each unit and the side of the appliance. The
levelling feet fitted to the appliance will achieve a
nominal height to hotplate trims of 900mm +20mm.
L.P.G. cookers MUST NOT be installed below ground
level, i.e. in a basement, or aboard any boat, yacht or
other vessel.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S 813 Current
Edition Section 7- Permitted Locations of Appliance.
Positioning the Cooker
Caution:
Some soft or badly fitted floor coverings can be
damaged when the cooker is moved across their
surface for cleaning. It is advisable to ensure that the
floor covering in the area below the cooker is either
securely fixed so as not to become damaged when the
cooker is moved or, if preferred, removed.
Installation
Positioning the Appliance (Fig. 1)
16
D
115
E
420
C
780
This appliance cannot be positioned on a
base.
The appliance cannot be installed beside or between
furniture units whose height exceeds the cooker
worktop.
Note A:
The appliance is designed to be flush fitted with 2mm
clearance at each side to allow for it to be pulled forward
for cleaning etc.
Note B:
The hotplate side trims should be flush with the cabinets
and must not be below. Adjustable levelling feet at the
front and rear are provided on the base of the appliance.
Adjustment is obtained by rotating in or out, the feet at
the front or rear of the appliance from the underside of
the appliance.
A spirit level should be placed on a cake tray on one of
the shelves to confirm that the appliance is correctly
levelled.
The levelling feet fitted to the appliance will achieve a
height to hotplate trims of 900mm-0 + 10.
Note C:
If the appliance is fitted next to a side wall or cabinets
above height of the hotplate trims, then a gap of 115
mm is required.
Curtains must not be fitted immediately behind the
cooker or within 115 mm of the sides of the cooker.
Note D:
Any wall cabinet or extractor must not be lower than
780mm above hotplate level.
Note E:
Wall cabinets may be fitted in line with the sides of the
base units, providing that the lower edge of the wall
cabinet is a minimum of 420mm above the worktop.
B
A
FO 1141
Fig. 1
300 mm.
WALL FACE
100 mm.
580 mm.
BACK OF COOKER
ENGAGEMENT EDGE FOR
STABILITY BRACKET
LEVELLING FEET
BASE OF COOKER
A
PENCIL LINE ON THE FLOOR
295 mm.
FO 0179
SIDE VIEW
OF THE COOKER
PLAN VIEW OF THE COOKER
Fig. 2
Fitting the Stability Bracket
(Not supplied)
If the cooker has to be installed with a flexible supply
pipe, it is necessary that a stability device is fitted.
(See "Important Safety Requirements").
The stability bracket should be fitted by the installer
and these instructions should be read in conjunction
with the leaflet packed with the stability bracket.
Place cooker in its intended position and level cooker.
Mark off 295mm (11 1/2") from the right hand side of the
cooker as shown, this is the centre line of the bracket
fixing.
Draw a line 100mm (4") from the front edge of the levelling
feet (see Fig. 1) and remove cooker from its position.
Mark off 580mm (23") back from this line on the centre
line of the bracket to locate the front edge of the lower
bracket.
Connecting to Gas
This cooker is designed to be installed with an appliance
flexible connection. Connection is made to the RC 1/2
(1/2" B.S.P.) threaded entry pipe located just below the
hotplate level on the rear right-hand side of the cooker.
Check for gas soundness after connecting the gas supply.
The gas bayonet connector must be fitted in the shaded
area indicated in Fig. 3. Take into account that it must
be possible to pull the cooker forward sufficiently. The
hose must not get caught on the stability bracket.
Note:
If using different types of gas bayonet connection, it may
not be possible for the appliance to be pushed fully back
to the wall stops.
Important:
Flexible tubing MUST comply with BS.669 Current
Edition.
Fix lower bracket (with two fixing holes) to the floor, then
measure height from floor level to engagement edge on
back of cooker, dimension 'A' of Fig. 2.
Assemble upper bracket to lower bracket so that
underside of bracket is dimension 'A' +3mm (1/8") above
floor level. Re-position cooker and check that top bracket
engages into cooker back to a depth of 75mm (3"), as
shown in Fig. 2.
600
450
Should the stability bracket currently installed not allow
the cooker to stand correctly, ask the installer to replace
it with the correct type.
130
FO 0180
Fig. 3
17
Electrical connections
Any electrical work required to install this cooker
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS COOKER MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This cooker is designed to be connected to a 230V 50Hz
AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the cooker rating
plate. The rating plate is located on the oven frame.
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the cooker
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
The switch must not break the yellow and green earth
wire at any point. The earth wire should be about 2 cm
longer than the neutral and live wires.
Ensure that the cooker supply cable does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
The cooker is supplied with a 3 core flexible supply cord
incorporating a 13amp plug fitted. In the event of having
to change the fuse, a 13amp ASTA approved (BS 1362)
fuse must be used. The plug should be inserted into a
proper socket and should be easily accessible upon
completion of the installation.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
the letter 'E' or the earth symbol
or coloured
green and yellow. The earth wire should be
about 2 cm longer than the neutral and live
wires.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that the
cut off plug is disposed of safely.
18
1
FO 0390
Commissioning
When the hob has been fully installed it will be
necessary to check the minimum flame setting. To do
this, follow the procedure below.
-
Turn the gas tap to the MAX position and ignite.
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
-
-
Re-ignite the burner and set to MIN.
Remove the control knob. According to the different
gas tap versions, the adjustment screw can be
located down the centre of the gas tap control shaft
or on the gas tap body istself (see diagram).
To adjust, use a thin bladed screwdriver and turn
the adjustment screw until the flame is steady and
does not extinguish, when the knob is turned from
MIN to MAX. Repeat this procedure for all burners.
Pressure Testing
-
Position of by-pass screw
(according to different gas
tap versions)
Remove left hand pan support and front left burner
cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another burner
supply.
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
Conversion from Natural Gas to LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted and the gas rate is adjusted to suit.
Method
•
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the appliance from the electricity supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
With the aid of a 7mm box spanner, the burner
injectors can then be unscrewed and replaced by
the appropriate LPG injectors (see Technical Data).
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw. Upon
completion, stick the replacement gas type label on
the back plate of the appliance.
IMPORTANT
The replacement/conversion of the appliance should
only be undertaken by a competent person
19
ZCM640/ZCM641
A
0,78 kWh
56
41 min.
1040 cm²
CUSTOMER CARE
Cornwall House
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
© Electrolux plc 2004
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
35687-5431
06/04
Grafiche MDM - Forlì
Zanussi-Electrolux