Veloci | High Speed Commercial Combination Oven | Owner`s manual | Veloci High Speed Commercial Combination Oven Owner`s manual

Owner's Manual
Contents
Model Identification ...................................2
PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY ........................... 2
IMPORTANT SAFETY INSTRUCTIONS ......... 3
High Speed Commercial
Combination Oven
Keep these instructions for future
reference. If the equipment changes
ownership, be sure this manual
accompanies equipment.
Grounding Instructions ..............................5
Installation .................................................5
Display and Features ................................. 6
Programming the Oven ............................... 9
EZCard Operating Instructions ................. 10
Using the Oven Control ............................ 11
User Options ............................................ 12
Care and Cleaning .................................... 13
Service Codes .......................................... 14
Troubleshooting ........................................ 14
Model Identification
When contacting Amana, provide product information.
Product information is located on oven serial plate.
Record the following information:
Any questions or to locate an authorized Amana servicer,
call Amana ComServ Service Support.
– Inside the U.S.A. or Canada, call toll-free at 866-4262621.
– Outside the U.S.A. and Canada, call 319-622-2808.
– Email: Commercialservice@amana.com.
Model Number: ____________________________
Serial or S/N Number: _______________________
Date of installation: _________________________
Dealer’s name and address: __________________
________________________________________
________________________________________
Warranty service must be performed by an authorized
Amana servicer. Amana also recommends contacting an
authorized Amana servicer, or Amana ComServ Service
Support if service is required after warranty expires.
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE
TO EXCESSIVE MICROWAVE ENERGY
A. DO NOT attempt to operate this oven with the door open since open door operation can result in harmful
exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
B. DO NOT place any object between the oven front face and the door or allow soil or cleaner residue to
accumulate on sealing surfaces.
C. DO NOT operate the oven if it is damaged. It is particularly important that the oven door close properly and
that there is no damage to the:
1. door (bent)
2. hinges and latches (broken or loosened)
3. door seals and sealing surfaces.
D. The oven should not be adjusted or repaired by anyone except properly qualified service personnel.
2
IMPORTANT SAFETY INSTRUCTIONS
Recognize this symbol as a SAFETY message
! WARNING
When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns,
electrical shock, fire, or injury to persons.
1. READ all instructions before using equipment.
2. READ AND FOLLOW the specific
PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY on page 2.
3. This equipment MUST BE GROUNDED. Connect
only to properly grounded outlet. See
GROUNDING INSTRUCTIONS on page 5.
4. Install or locate this equipment ONLY in
accordance with the installation instructions in
this manual.
5. Some products such as whole eggs and sealed
containers—for example, closed glass jars—are
able to explode and SHOULD NOT be HEATED in
this oven.
6. Use this equipment ONLY for its intended use as
described in this manual. Do not use corrosive
chemicals or vapors in this equipment. This type of
oven is specifically designed to heat or cook. It is
not designed for industrial or laboratory use.
7. As with any equipment, CLOSE SUPERVISION is
necessary when used by CHILDREN.
8. See door cleaning instructions in Care and
Cleaning section of manual on page 13.
9. DO NOT heat baby bottles in oven.
10. Baby food jars shall be open when heated and
contents stirred or shaken before consumption, in
order to avoid burns.
11. DO NOT operate this equipment if it has a
damaged cord or plug, if it is not working properly,
or if it has been damaged or dropped.
13. DO NOT cover or block any openings on the
equipment.
14. DO NOT store this appliance outdoors.
DO NOT use this product near water – for
example, near a kitchen sink, in a wet basement,
near a swimming pool, or similar locations.
15. DO NOT immerse cord or plug in water.
16. Keep cord AWAY from HEATED surfaces.
17. DO NOT let cord hang over edge of table or
counter.
18. For commercial use only.
19. DO NOT insert oversized foods or oversized
utensils in a microwave/convection oven as they
may create a fire, an electrical arc, or risk of
electrical shock.
20. DO NOT clean with metal scouring pads. Pieces
can break off the pad and touch electrical parts
involving risk of electrical shock.
21. DO NOT use paper products not intended for
cooking when equipment is operated in
convection or combination mode.
22. DO NOT store any materials, other than
manufacturer's recommended accessories, in this
equipment when not in use.
23. DO NOT cover any part of the oven with metal foil.
Airflow restriction will cause overheating of the
oven.
24. DO NOT spray oven cleaning solutions toward the
rear inner cavity surface. This will contaminate and
damage the convection heating assembly.
12. This equipment, including power cord, must be
serviced ONLY by qualified service personnel.
Special tools are required to service equipment.
Contact nearest authorized service facility for
examination, repair, or adjustment.
SAVE THESE INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
! WARNING
! WARNING
Liquids such as water, coffee, or tea are able to be
overheated beyond the boiling point without appearing
to be boiling due to surface tension of the liquid.
Visible bubbling or boiling when the container is
removed from the microwave oven is not always
present. THIS COULD RESULT IN VERY HOT
LIQUIDS SUDDENLY BOILING OVER WHEN A
SPOON OR OTHER UTENSIL IS INSERTED INTO
THE LIQUID. To reduce the risk of injury to persons:
To avoid risk of fire in the oven cavity:
a. DO NOT overcook food. Carefully attend oven
when paper, plastic, or other combustible
materials are placed inside the oven to facilitate
cooking.
b. Remove wire twist-ties from paper or plastic
bags before placing bag in oven.
c. If materials inside the oven ignite, keep oven
door CLOSED, turn oven off and disconnect the
power cord, or shut off power at the fuse or
circuit breaker panel.
d. DO NOT use the cavity for storage. DO NOT
leave paper products, cooking utensils, or food
in the cavity when not in use.
i)
ii)
Do not overheat the liquid.
Stir the liquid both before and halfway through
heating it.
iii) Do not use straight-sided containers with narrow
necks.
iv) After heating, allow the container to stand in the
microwave oven for a short time before removing
the container.
v) Use extreme care when inserting a spoon or
other utensil into the container.
! CAUTION
To avoid risk of personal injury or property damage, observe the following:
8. Oven temperature is at least 450°F in convection
mode. Verify plastic, paper or other combustible
materials are recommended by the manufacturer to
withstand the maximum oven temperature.
1. Do not deep fat fry in oven. Fat could overheat
and be hazardous to handle.
2. Do not cook or reheat eggs in shell or with an
unbroken yolk using microwave energy. Pressure
may build up and erupt. Pierce yolk with fork or
knife before cooking.
9. When cooking with paper, plastic, or other
combustible materials, follow manufacturer's
recommendations on product use.
3. Pierce skin of potatoes, tomatoes, and similar
foods before cooking with microwave energy.
When skin is pierced, steam escapes evenly.
10. Do not use paper towels which contain nylon
or other synthetic fibers. Heated synthetics could
melt and cause paper to ignite.
4. Do not pop popcorn in this oven.
11. Do not heat sealed containers or plastic bags in
oven. Food or liquid could expand quickly and cause
container or bag to break. Pierce or open container
or bag before heating.
5. Do not use regular cooking thermometers in oven
when cooking in microwave or combination mode.
Most cooking thermometers contain mercury and
may cause an electrical arc, malfunction, or
damage to oven.
12. Racks, utensils, rack guides, and oven surfaces may
become hot during or after use. Use utensils or
protective clothing, like pan grips or dry oven mitts,
when necessary to avoid burns.
6. Do not use metal utensils in oven except when
recommended by microwave food manufacturers
or recipe requires metal utensils in convection or
combination mode. Heat food in containers made
of glass or china if possible.
13. Do not unplug oven immediately after use. Internal
fan must cool oven to avoid damage of electrical
components.
7. Never use paper, plastic, or other combustible
materials that are not intended for cooking. If oven
temperature is high, material may ignite.
14. To avoid pacemaker malfunction, consult physician
or pacemaker manufacturer about effects of
microwave energy on pacemaker.
SAVE THESE INSTRUCTIONS
4
Installation
Unpacking Oven
•
•
•
•
Inspect oven for damage such as dents in door or inside oven cavity.
Report any dents or breakage to source of purchase immediately.
Do not attempt to use oven if damaged.
Remove all packing materials from oven interior.
If oven has been stored in extremely cold area, wait a few hours before
connecting power.
Radio Interference
Microwave operation may cause interference to WiFi network, radio, television,
or a similar oven. Reduce or eliminate interference by doing the following:
• Clean door and sealing surfaces of oven according to instructions in
Care and Cleaning section.
• Place WiFi network, radio, television, etc. as far as possible from oven.
• Use a properly installed antenna on radio, television, etc. to obtain
stronger signal reception.
Oven Placement
•
•
•
•
•
Recommended countertop surface depth is 26”.
Do not install oven next to or above source of heat, such as pizza oven
or deep fat fryer. This could cause microwave oven to operate improperly
and could shorten life of electrical parts.
Do not block or obstruct oven filter. Allow access for cleaning.
Install oven on level countertop surface.
Outlet should be located so that plug is accessible when oven is in place.
A—For North American (60 Hz) models,
allow at least 2” (5.1 cm) of clearance
around top of oven. For International
(50 Hz) models, allow at least 12” (30
cm) of clearance around top of oven.
Proper air flow around oven cools
electrical components. With restricted
air flow, oven may not operate
properly and life of electrical parts is
reduced.
B—Allow at least 2” (5.1 cm) between air
discharge on back of oven and back
wall.
C—Allow at least 5” (12.7 cm) of clearance
around sides of oven.
A
B
C
Install Accessories
•
•
Install rack guides and rack, or PS10 (Pizza Stone)
1. Oven cavity must be cool to touch.
2. Both guide rails must be installed in oven (refer to Owner’s Manual).
3. Place the rack or pizza stone rack securely in the guide rails.
4. If using the pizza stone rack,
• Place pizza stone on the pizza stone rack
• To cure stone:
1. Heat oven to 475° F or 250° C
2. Place stone in preheated oven for 1 hour
3. Pizza stone is ready to use
Make sure OV10 (Oven Liner) is placed in bottom of oven.
DO NOT cook food directly on floor of oven.
Place OV10 (oven liner)
in bottom of oven.
Place the oven rack securely in the
guide rails, NOT on bottom of oven.
Grounding/
Earthing
Instructions
Oven MUST be
grounded.
Grounding reduces risk of electric
shock by providing an escape wire for
the electric current if an electrical
short occurs. This oven is equipped
with a cord having a grounding wire
with a grounding plug. The plug must
be plugged into an outlet that is
properly installed and grounded.
Consult a qualified electrician or
servicer if grounding instructions are
not completely understood, or if
doubt exists as to whether the oven
is properly grounded.
Oven Clearances
•
WARNING
To avoid risk of electrical shock
or death, this oven must be
grounded and plug must not be
altered.
PS10 Pizza Stone on
pizza stone rack.
5
Do not use an extension cord.
If the product power cord is too
short, have a qualified electrician
install a three-slot receptacle. This
oven should be plugged into a
separate circuit with the electrical
rating as provided in product
specifications. When the combination
oven is on a circuit with other
equipment, an increase in cooking
times may be required and fuses can
be blown.
External Equipotential
Earthing Terminal (export only)
Equipment has secondary earthing
terminal. Terminal provides external
earthing connection used in addition
to earthing prong on plug. Located
on outside of oven back, terminal is
marked with symbol shown below.
Display and Features
A—Oven Door Handle
(Lift to open.)
B—Door Shield
C—Top Control Panel
D—Display
E—Side Control Panel
F—Discharge Air Vent
G—Air Intake Filter
H—Exhaust Flue
I—Unit Spacing Bar
J—Power Cord
Oven Features
ITEM flashes in display indicating keypads can
be used and cooking entries can be made.
ITEM
Temperature is displayed in the
time field.
:
STG QTY
8
Display
POWER
H8
STANDBY
COOK
LEVEL
PREHEAT NOT READY indicates the oven is not at preheat temperature. NOT
flashes while the oven heats to preheat temperature.
If Item is not
displayed,
keypad will
not accept
entries. To
activate
keypad, open
and close oven
door—Item
will then
display.
ITEM
:
STG QTY
8
POWER
H8
COOK
STANDBY LEVEL
Preheat ready displays when oven
has reached the preset preheat
temperature.
6
Display and Features (cont’d)
Displays stage the oven is cooking in
during multi-stage cooking programs.
Displays
programmed
ITEM digit
pad selected
by user.
:
ITEM
Convection cooking only.
Displays when changing heater setting.
Press and hold TEMP ENTRY to display.
POWER
ITEM
COOK
LEVEL
Displays when changing fan setting. Press
and hold POWER LEVEL to display.
POWER
ITEM
COOK
LEVEL
Time left in cooking condition.
ITEM
Power displays when oven is actively generating
microwave energy. Will not display when set at 0,
and will turn on and off when set less than HI.
Indicates
percentage of
microwave power
(0 to 100%).
9 is 90%,
5 is 50%,
H is High (100%).
:
Cook level displays with the amount
of microwave energy used.
Combination cooking: both convection
(C) and microwave energy (M) are used.
7
Display and Features (cont’d)
HIDDEN
PAD
PREHEAT
ON/OFF
TIME
ENTRY
TEMP
ENTRY
POWER
LEVEL
STAGE
PROGRAM
SAVE
Cooking Display
START Pad
DISPLAYS
DESCRIPTION
Press the START
pad to restart a
cooking cycle that
was interrupted.
PREHEAT
READY
PREHEAT READY displays when oven has
reached preheat temperature and is ready to cook.
00:00
Displays cooking time. If stage cooking is
programmed, total cooking time is displayed.
PREHEAT
NOT READY
PREHEAT NOT READY displays with NOT flashing
when oven is turned on and warming to preheat temp.
(475°F factory default preheat setting or 450°F)
STOP/RESET
Pad
The STOP/RESET
pad stops a cooking sequence in
COOK
progress, and can clear out any
LEVEL
remaining time. The first time STOP/
RESET is pressed, it will pause the
current cooking cycle. The second
time STOP/RESET is pressed, the
ITEM
remaining time will be cleared from
the oven.
HIDDEN Pad
HIDDEN
PAD
Press the HIDDEN
pad to change User
Options.
COOK LEVEL displays the current microwave
power level. HI is the highest setting, and 0 is lowest
(no microwave energy used).
ITEM displays the single or double digit entry of a
cooking program when using a programmed pad.
ITEM also flashes when a cooking condition can be
started or programmed.
STG
STG displays with a single number. This is the stage
the oven is at in the cooking program.
STANDBY
STANDBY displays when the oven is plugged in,
and turned off.
CM
C M displays when oven is convection cooking.
CM
C M displays when oven is cooking using both
microwave energy and convection.
POWER
POWER displays during active microwave energy in the
oven. POWER will not display when power setting is at
0; and POWER will turn on and off when microwave
energy is set at less than HI.
CLEAN FILTR
Displays every 7 days after start up of oven. Will
disappear after 24 hours. This is to remind you to clean
the filter.
HTR
Displays when changing heater setting. Press and hold
TEMP ENTRY to display (in programming mode).
FAN
Displays when changing fan setting. Press and hold
POWER LEVEL to display (in programming mode).
8
Programming the Oven
Programming Items
1. Oven must be ON.
• Press PREHEAT ON/OFF.
• ITEM must flash in display. If not, open and close oven door.
2. Press PROGRAM SAVE.
3. Press pad to be programmed or reprogrammed.
4. Press TIME ENTRY to program amount of cooking time.
• Enter desired cooking time by using numeric keypad.
• The total microwave cooking time (all stages combined) is 20 minutes.
5. If you wish to change oven temperature press TEMP ENTRY and enter desired
oven temperture by using numeric keypad. If not, skip to #6.
• Oven temperature can be set to either 450°F (240°C) or 475°F (250°C).
6. Press and hold TEMP ENTRY to program the radiant heater. HTr shows in the
display. Radiant heater setting automatically defaults to 9 (highest).
• Set radiant heater by pressing pads 0 through 9.
• Pad 1 is the lowest heater setting; pad 9 is the highest heater setting. 0 turns off
radiant heater.
7. Press POWER LEVEL to program level of microwave power. Power level
automatically defaults to High (100%).
• For a lower microwave power, press pads 1 (for 10%) through 9 (for 90%). 0
turns off microwave power.
8. Press and hold POWER LEVEL to program fan speed. FAn shows in the display.
Fan speed setting automatically defaults to 9 (fastest).
• Set fan speed by pressing pads 1 through 9.
• Pad 1 is the slowest fan speed; pad 9 is the fastest fan speed.
9. If stage cooking is desired, press STAGE.
• Enter cook time, radiant setting, fan setting, and power level for each stage by
repeating steps 4-8.
• To enter another cooking stage for that pad, press STAGE pad again. Up to four
different stages can be programmed for a total of 20 minutes microwave cooking
time.
10. Press the PROGRAM SAVE pad to save the programming into the pad.
What is stage
cooking?
Stage cooking enables up to
four different cooking cycles, or stages, to
be used consecutively without repeated
input from the user.
Example of Stage Cooking Conditions
Stage 1
Stage 2
Stage 3
Stage 4
Temp
250°C
250°C
250°C
250°C
Power
H (high)
3
0
0
Time
2:30
1:30
1:30
1:00
Heater
9
9
5
5
Fan
9
9
5
5
9
EZCard Operating Instructions (some models only)
PREHEAT
ON/OFF
TIME
ENTRY
TEMP
ENTRY
POWER
LEVEL
EZCard slot
STAGE
PROGRAM
SAVE
EZCard
To program the oven using the EZCard:
Oven must be in Standby mode (Preheat must be OFF)
1. Remove magnetic cover from bottom of control panel. Set
magnetic cover aside.
2. Insert the EZCard into the slot located below the vertical keypad.
• The EZCard can be inserted forwards or backwards.
3. Press and hold the PROGRAM SAVE pad for 3 seconds.
• AUTO, then PROG displays briefly, repeating this sequence every
second as the EZCard automatically programs the oven.
• When the oven programming is complete, done shows in the
display for 3 seconds and the oven beeps.
• The oven resets to the standby mode.
4. Remove the EZCard.
• The oven programming is now complete.
5. Place magnetic cover back over slot in bottom of control panel.
NOTE: If 00:00 displays, 3 beeps
sound and the display returns to
the Standby mode, the EZCard
was not detected.
• Reinsert the EZCard into the
slot and try each step again.
• If after several attempts, the
EZCard is still not detected,
contact Amana ComServ
Service Support.
– Inside the U.S.A. or Canada,
call toll-free at 866-426-2621.
– Outside the U.S.A. and
Canada, call 319-622-2808.
– Email:
Commercialservice@amana.com.
Caution:
DO NOT REMOVE EZCard while programming. Removing card during
programming can cause the oven’s keypad to freeze up.
STOP!
Use this option only to transfer data from the oven TO the
EZCard. This will overwrite all programming on the EZCard!
To transfer programming from the oven to the EZCard:
Oven must be in Standby mode (Preheat must be OFF)
1.
2.
3.
4.
5.
6.
7.
Remove magnetic cover from bottom of control panel. Set magnetic cover aside.
Insert the EZCard into the slot located below the vertical keypad.
• The EZCard can be inserted forwards or backwards.
Press the PROGRAM SAVE pad.
Press the START pad.
Press the 1 pad, the 3 pad, and then the 5 pad.
• The programming transfer will begin automatically and the display will show moving dashes.
• When the programming transfer is complete, done shows in the display for 3 seconds and the oven beeps.
• The oven resets to the standby mode.
Remove the EZCard.
• The programming transfer is now complete.
Place magnetic cover back over slot in bottom of control panel.
10
To order additional
EZCards, call the Amana
Commercial Inside Sales
Team toll-free at 800-2332366 (U.S.A. or Canada),
or 319-622-8307 (outside
the U.S.A. and Canada).
Using the Oven Control
CAUTION
To avoid risk of burns, handle utensils, accessories, and door with care. Allow oven, utensils, and
accessories to cool before cleaning. Oven, utensils, and accessories become hot during operation.
Cooking with Preprogrammed Pads
Follow the steps outlined below to use preprogrammed pads.
1.
2.
3.
4.
5.
Press PREHEAT ON/OFF to start the oven.
• Oven begins a preheat cycle.
• PREHEAT NOT READY displays with NOT flashing.
Oven reaches preheat temperature.
• Signal sounds and PREHEAT READY displays.
Enter selected item number using digit pad(s).
• ITEM must be flashing in display. If not, open and close door.
• If using single digit programming, press pad and oven begins automatically.
• For double digit programming, press pads in proper sequence and oven begins automatically.
Cooking cycle begins
• Total cooking time is displayed.
Oven finishes cooking sequence
• An end of cycle beep signals the end of the cooking cycle.
• Oven interior and accessories will be hot.
Manual Operation
To cook food using a specific entered time and power level.
1.
Press PREHEAT ON/OFF to start the oven.
• Preheat temperature and PREHEAT NOT READY displays with
NOT flashing.
2. Oven reaches preheat temperature.
• Signal sounds and PREHEAT READY displays.
3. ITEM must be flashing in display. If not, open and close oven door.
4. Press TIME ENTRY to program amount of cooking time.
• Enter desired cooking time by using numeric keypad.
• The total microwave cooking time (all stages combined) is 20
minutes.
5. If you wish to change oven temperature, press TEMP ENTRY and
enter desired oven temperature by using numeric keypad. If not, skip
to #6.
• Oven temperature can be set to either 450°F (240°C) or 475°F
(250°C).
6. Press and hold TEMP ENTRY to program the radiant heater. HTr
shows in the display. Radiant heater setting automatically defaults to 9
(highest).
• Set radiant heater by pressing pads 0 through 9.
• Pad 1 is the lowest heater setting; pad 9 is the highest heater setting.
0 turns off radiant heater.
7. Press POWER LEVEL to program level of microwave power. Power
level automatically defaults to High (100%).
• For a lower microwave power, press pads 1 (for 10%) through 9
(for 90%). 0 turns off microwave power.
8. Press and hold POWER LEVEL to program fan speed. FAn shows in the
display. Fan speed setting automatically defaults to 9 (fastest).
• Set fan speed by pressing pads 1, 3 or 9.
• Pad 1 is a slow fan speed; pad 3 is a medium fan speed; pad 9 is a
fast fan speed.
9. If stage cooking is desired, press STAGE.
• Enter cook time, oven temperature, radiant setting, fan setting, and
power level for each stage by repeating steps 4-9.
• To enter another cooking stage for that pad, press STAGE pad
again. Up to four different stages can be programmed for a total of
20 minutes microwave cooking time.
10. Place food in oven and press the START pad to begin the cooking
cycle.
11
The keypad
doesn’t work.
The keypad is designed only
to accept time entry within so
many seconds after the oven door is
closed. To start keypad entry, simply
open and close oven door.
Programming
Preheat Setting
The convection temperature setting
can be set between 240°C to 250°C
(450°F to 475°F). It is recommended
to set the preheat setting to the most
commonly used temperature. The
factory default preheat setting is
250°C (475°F).
To program the preheat setting:
1. Oven must be ON.
• Press PREHEAT ON/OFF.
2. Press PROGRAM SAVE pad.
3. Press TEMP pad.
4. Enter desired temperature by
using the numeric key pads.
5. Preheat temperature is changed.
User Options
Can I change an option?
CLEAN FILTR
This oven displays CLEAN FILTR every
7 days. When the message displays,
Amana recommends cleaning the air
filter thoroughly. Cleaning the air
filter will not shut off the
message. The message will
automatically stop displaying after 24
hours. Depending on microwave use
and environmental conditions, the
filter may need to be cleaned more or
less frequently. Once the frequency
is determined, set the option for the
appropriate time frame.
Air filter and vents must be cleaned
regularly to prevent overheating of the
oven. Refer to page 12 of the Owner’s
Manual for complete cleaning
instructions.
Options such as single or double digit pad programming and beep volume can
be changed to suit individual preferences.
To change options, STANDBY must display. If STANDBY is not
displayed, press PREHEAT ON/OFF pad.
1. Press HIDDEN pad.
• Pad is unmarked and located to the immediate left of PREHEAT ON/
OFF pad.
• Nothing will be displayed when HIDDEN pad is pressed.
2. Press PROGRAM SAVE pad.
• 0P:-- displays. Oven is now in options mode.
3. Press number pad that controls option to be changed.
• See table below for options.
• Current option will display.
4. Press number pad again to change the option.
• Each time pad is pressed, option will change.
• Match code displayed with code for desired option.
5. Press PROGRAM SAVE pad to save changes.
• To change additional options, repeat steps 3 - 5.
• Changes take affect after PROGRAM SAVE pad is pressed.
6. Press STOP/RESET to return to STANDBY, or open and close oven door.
Numbered Pads
Display
1
Preprogrammed Pads
2
Manual Time Entry
3
Reset to READY mode
4
Keybeep
OP:10
OP:11
OP:20
OP:21
OP:30
OP:31
OP:40
OP:41
OP:50
OP:51
OP:52
OP:53
OP:60
OP:61
OP:62
OP:63
OP:70
OP:71
OP:72
OP:73
OP:80
OP:81
OP:82
OP:83
OP:b0
OP:b1
Allows 10 (0-9) preprogrammed digit pads.
Allows 100 (00-99) preprogrammed digit pads.
Manual time entry/cooking not allowed
Manual time entry/cooking allowed
Opening oven door does not erase remaining cooking time and/or program
Opening oven door erases remaining cooking time and/or program
Keys do not beep when pressed (keybeep off)
Keys beep when pressed (keybeep on)
Keybeep volume OFF
Keybeep volume low
Keybeep volume medium
Keybeep volume high
Food done signal is a continuous beep until reset by user
Food done signal is a three second beep
Food done signal is four beeps, continuously.
Food done signal is four beeps, four times
Keypad time entry window is 15 seconds
Keypad time entry window is 30 seconds
Keypad time entry window is one minute
Keypad time entry window is two minutes
Both temperature warnings off
Warning only when preheat temperature does not match preprogrammed temperature
Warning only when actual oven cavity temperature is not to preheat temperature
Both temperature warnings on
°F
°C
°C is default in 50 Hz International models
STAGE PAD (E)
Clean Filter Message
OP:E0
OP:E1
OP:E2
OP:E3
Do not display message
Display message for 24 hours every 7 days
Display message for 24 hours every 30 days
Display message for 24 hours every 90 days
POWER LEVEL (A)
Altitude Adjustment
OP:A0
OP:A1
Use at an elevation below 5,000 ft.
Use at an elevation of 5,000 ft. or above
5
Keybeep Volume
6
Food Done Signal
7
Keypad Time Entry
8
Temperature Warnings
TEMP PAD (b)
Temperature Scale
Options (Factory Settings in Bold)
12
Care and Cleaning
Daily Cleaning Recommendations: Follow the recommendations below for proper maintenance of the Amana® Veloci™ oven.
Please Note: The use of caustic cleaning products or those containing ammonia, phosphates or chlorine can damage critical oven parts and may
void the warranty on those parts. Do not use water pressure type cleaning systems.
Recommended Cleaning Supplies:
Plastic scraper or plastic putty knife, scrub pad or nylon sponge, cleaning towel and EcoLab Grease Cutter NC.
! CAUTION
To prevent burns, handle utensils, accessories, and
door with care. Allow oven, utensils, and accessories to
cool before cleaning. Oven, utensils, and accessories
become hot during operation.
Shut Oven Off
Clean Oven Interior
Turn oven off by pressing PREHEAT
ON/OFF button. Open oven door
and allow oven to cool. Cooling
takes approximately 60-90 minutes.
Clean the oven door and interior using a
plastic or nylon scouring pad. Apply
necessary pressure to remove particles
from oven. If necessary, a plastic
scraper can be used to remove
remaining residue.
Remove Rack and
Accessories
Wipe Oven Interior
Using a damp clean towel, wipe the oven
interior. Rinse towel and wring dry and repeat
2-3 times to remove remaining oven cleaner
and particles from the oven.
After oven has cooled remove
accessories, rack and rack guides
from oven. Wash with warm, soapy
water (except for pizza stone) and
allow to air dry while cleaning oven
interior. Clean pizza stone by using a
plastic scraper and a damp cloth only.
Clean Air Filter
(reminder displays every 7 days)
Remove the air filter at the base of the oven
by turning the screws counter-clockwise on
each side of the filter. Wash filter in a mild
detergent solution made with warm water.
Rinse and dry thoroughly. Replace filter by
turning screws clockwise.
Remove Baked on
Particles
Use a plastic scraper to remove
baked on particles from oven floor,
rear, sides and door. When finished
scraping, use a damp cloth to remove
particles from oven.
Place Rack and Accessories
Back in Oven
Place rack guides and rack back in the
desired position of the oven. Place the oven
liner on the oven floor.
Spray Oven Interior
Clean Oven Exterior
Put on rubber gloves. Spray oven
door, sides and floor with EcoLab
Grease Cutter NC. Allow to soak for
5-10 minutes.
Clean exterior door, discharge vents,
magnetic door stop and other surfaces with a
clean cloth, sponge or nylon pad using a mild
detergent and warm water solution. Wring
cloth well to remove excess moisture before
wiping oven.
DO:
- Clean oven daily
- Use EcoLab Grease Cutter NC or another
non-caustic cleaner
- Remove food from oven at end of cycle
- Use only accessories that are both high
temperature oven-safe and microwave-safe
in the oven
-
DO NOT:
DO NOT use caustic cleaning products or those
containing ammonia, phosphates or chlorine
DO NOT use a water-pressure type cleaning system
DO NOT cook foods with plastic wrap on them
DO NOT use metal pans or foil in the oven
13
Before Calling for Service
! WARNING
To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time.
Only an authorized servicer should remove outer case.
Problem
Possible Cause
Confirm oven is plugged into dedicated circuit.
Confirm oven is on grounded circuit.
(Contact electrician to confirm)
Oven does not operate.
Check fuse or circuit breaker.
Oven operates intermittently.
Check air filter and discharge areas for obstructions.
If oven does not accept entries
when pad is pressed.
Make sure oven is on and preheated.
Open and close oven door. Press pad again.
Oven control is equipped with a self-diagnostic system. Self-diagnostic
system alerts you if there is an error or problem. When electronic control
signals a problem, follow steps listed below.
1. Record error number shown in display of oven.
2. Press STOP/RESET pad to clear ERR_.
3. Press PREHEAT ON/OFF pad to restart oven.
If oven malfunctions or shows
“
4. If ERR_ code does NOT re-appear, continue normal use of oven.
ERR_”:
5. If failure continues, unplug oven for one minute and plug back in, then
press PREHEAT ON/OFF pad.
6. If ERR_ code does NOT re-appear, continue normal use of oven.
7. If failure continues, discontinue use and contact an authorized Amana
servicer or call Amana toll free at 1-866-426-2621 inside the U.S.A. or
Canada, or 319-622-5511 outside the U.S.A. or Canada.
Oven fan turns on while oven is
not preheating or cooking.
Normal operation. Will run 45 minutes after oven is turned OFF.
"PREHEAT NOT READY"
displays when cook pad is
pressed.
Oven is operating normally. Display flashes "PREHEAT NOT READY" if
the preheat temperature is different than programmed cooking cycle
temperature.
Clean Filtr displays
This is normal and will appear for 24 hours every 7 days. This is a reminder
to keep the filter clean to keep the oven in peak performance. The
message will turn off by itself; a servicer does not need to be contacted.
HOT displays
Part No. 12878501
Revised 4/06
-
If a power interruption occurs and oven is at full temperature, HOT may
appear in the display. The oven will not operate until it cools down by
leaving door open for 20 minutes, or keeping door closed for 45
minutes.
-
Oven’s magnetron is overheated. Oven automatically interrupts
cooking sequence and turns on cooling fan until normal temperature is
reached. When magnetron cools to normal temperature, oven returns
to READY mode.
For full product documentation visit:
™
www.amanacommercial.com/wavelink
14
© 2006 Amana Commercial Products
Amana, Iowa 52204
Download PDF