Sharp XE-A41S Service manual

PROGRAMMING MANUAL
CODE : 00Z XEA41SUPME
LEAD-FREE SOLDER MODEL
ELECTRONIC
CASH REGISTER
MODEL
XE-A41S
CONTENTS
CHAPTER 1. MASTER RESET AND PROGRAM RESET . . . . . . 1 - 1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . 2 - 1
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE. . . . . . . . . . . . . . . . . . 3 - 1
Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
■ LEAD-FREE SOLDER
The PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The
alphabet following the LF mark shows the kind of lead-free solder.
Example:
<Solder composition code of lead-free solder>
Lead-Free
5mm
Solder composition
code (Refer to the
table at the right.)
a
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi
z
Sn-In-Ag-Bi
i
Sn-Cu-Ni
n
Sn-Ag-Sb
s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to
conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean
and file the tip with steel wool or a fine filer.
XE-A41S LEAD-FREE SOLDER
CHAPTER 1. MASTER RESET AND PROGRAM RESET
1. MASTER RESETTING
Master resetting clears the entire memory and resumes initial values.
Master resetting can be accomplished by using the following procedure:
Procedure :
1) Unplug the AC cord from the wall outlet.
2) Set the mode switch to the PGM position.
3) While holding down both the JOURNAL FEED key and [CL] key, plugin the AC cord to the wall outlet.
2. PROGRAM RESETTING (INITIALIZATION)
This resetting resumes the initial program without clearing memory.
This resetting can be operated at below sequence in PGM mode.
Procedure:
1) Unplug the AC cord from the wall outlet.
2) Set the mode switch to the PGM position.
3) While holding down both JOURNAL FEED key and RECEIPT FEED key, plugin the AC cord to the wall outlet.
XE-A41S
MASTER RESET and program reset
1–1
CHAPTER 2. PROGRAM MODE
1. READING STORED PROGRAMS
The machine allows you to read every program stored in the PGM mode.
■ Key sequence for reading stored program
Report name
Key sequence
Programming report 1
CA/AT/NS
Programming report 2
2 3 CA/AT/NS
[Auto] key programming report
1 3 CA/AT/NS
Printer density report
3 3 CA/AT/NS
PLU programming report (*1)
Start no.
@/FOR
End no.
PLU/SUB
(*1) PLU or UPC code range can be specified by entering the start and end numbers according to the following procedure.
When specifying a single time interval, PLU code or UPC code, the start number has only to be entered.
■ SAMPLE PRINTOUTS
1. Programming report 1
HEADER
DATE /TIME /CLERK NO
11/01/2003 12:34PM
123456#1234
01
BETTY___
MACHINE NO. /CC-NO. /
CLERK NAME
MODE TITLE
*PGM*
D01
T1234
0073
DPET.01xxxxxx
-1234.56
G0 C0
0073
D02
T1234
DPET.02
G0 C0
-1234.56
:
:
D99
T1234
0071
DPT.99
G0 C0
0.00
F01 ( - ) xx
007
-1000.00
000
F02 % 1xxxx
L100.00% T1234 -10.00%
000
F03 % 2xxxx
L100.00% T1234 -100.00%
F04 NET1
F05 TAX1 ST
F06 GRS TAX1
F07 RFD TAX1
F08 TAX1
F09 TX1 EXPT
:
:
F25 GRS MTAX
F26 RFD MTAX
7
F27 M-TAX
:
:
9
F37 ***RAxxx
9
F38 ***POxxx
F39 TRANS CT
F40 NET3
DEPT CODE /TAXABLE/
PROGRAM (*1)
TEXT
DEPT GROUP /COMMISSION
GROUP /PRICE WITH SIGN
(MAX department is decided by
PGM selection.)
FUNCTION NO. /TEXT /PROGRAM (*2)
AMOUNT WITH SIGN
FUNCTION NO. /TEXT /PROGRAM (*2)
HALO WITHOUT SIGN/
RATE WITH SIGN
FUNCTION NO. /TEXT
FUNCTION NO. /TEXT /HALO
FUNCTION NO. /TEXT /HALO
XE-A41S
008
F 41 CASH
008
F 42 CHECKxxx
008
F 43 CHRAGExx
F 44 CHARGEF 45 CHARGE2
008
F 46 CHARGE200
F 47 CONV 1
AAAA
9999.9999
F 48 CONV 2
F 49 ****CID
F 50 CA+CH ID
F 51 CHK /CG
F 52 COM.SAL1 10.00%
F 53 COM.SAL2 100.00%
F 54 NON COM.
:
F 76 COPY
F 77 GROUP01
:
F 85 GROUP09
F 86 DUE
F 87 TAX ST
SHARP
PRESENTS THE
BEST ECR
SHARP
IS
THE BEST
#5
00000000
00000011
#6
00000000
#7
0000
#10
#11
0
00000000
#15
00000000
#16
9999999.99
#20
007
#35
50
#50
10.0000%
T1
/ 1.00
1 0.11
2 0.23
3 0.57
4 0.78
5 1.11
4.0000%
T2
0.10
5.0000%
T3
0.20
-----T4
C#01
CLERK.01
C#02
CLERK.02
:
:
C#40
CLERK.40
PROGRAM MODE
2–1
FUNCTION NO. /TEXT /PROGRAM (*3)
FUNCTION NO. /TEXT /PROGRAM (*4)
CURRENCY SYMBOL /RATE
FUNCTION NO. /TEXT
FUNCTION NO. /TEXT/
COMMISSION RATE
FUNCTION NO. /TEXT
FUNCTION NO. /TEXT
LOGO TEXT
(It is according with LOGO FORMAT.)
(JOB# 5) FUNCTION SELECT
(JOB# 6) PRINT FUNCTION
(JOB# 7) RECEIPT PRINT FORMAT
(JOB#10) POWER SAVING PROGRAMMING
(JOB#11) LOGO FORMAT
(JOB#15) FUNCTION SELECT2
(JOB#16) UPC /EAN FUNCTION
(JOB#20) SENTINEL (CID HALO)
(JOB#35) ONLINE Timeout time
(JOB#50) TERMAL PRINTER DENSITY
CONTROL
TAX1 RATE
CYCLE
TAX /BREAK POINT AMOUNT
TAX2 RATE
LOWER TAX LIMIT
TAX3
TAX4 ("------": INHIBIT)
Clerk No. /Clerk name
: VARIOUS PROGRAM
Refer to the programming section
about the data of each JOB.
2. Programming report 2
(*1) DEPT PROGRAM : ABCD
A: KINDS
A
NORMAL
0
BOTTLE RETURN
1
HEADER
B: REGISTRATION TYPE
B
11/01/2003 12:34PM
NORMAL
0
123456#1234
SICS
1
*PGM*
#61
00000000
#62
00000000
#63
00000000
#64
00000000
#65
00000000
#66
00000000
#67
00000000
#68
00000000
#69
00000000
#70
00000000
#71
$00000000000.00
GT2
#72
$00000000000.00
GT3
#76
Z1 0000
#77
Z2 0000
#85
___$
#86
00
#87
TRAINING
#88
0
#95
99
DATE /TIME /CLERK NO
D
Inhibited
0
Open
1
Preset
2
Open and Preset
3
(*2) (−)/[%] PROGRAM : ABC
A: ENTRY FOR ITEM
A
ENABLE
0
DISABLE
1
B: ENTRY FOR SBTL
BETTY___
B
ENABLE
0
DISABLE
1
MACHINE NO. /CC-NO. /
CLERK NAME
MODE TITLE
C: LIMITATION DIGITS (*2) = 0 to 7
D: AMOUNT ENTRY TYPE
01
(JOB#61)
(JOB#62)
(JOB#63)
(JOB#64)
(JOB#65)
(JOB#66)
(JOB#67)
(JOB#68)
(JOB#69)
(JOB#70)
OTHERS1
OTHERS2
OTHERS3
OTHERS4
OTHERS5
OTHERS6
OTHERS7
OTHERS8
OTHERS9
OYTHERS10
GT2
GT3
GENERAL Z1 RESET COUNTER
GENERAL Z2 RESET COUNTER
DOMESTIC CURRENCY SYMBOL
TRAINING CLERK
TRAINING MODE TEXT
LANGUAGE MODE
(For the fixed messages)
MAX NUBMER OF DEPT
: OTHERS PROGRAM
Refer to the programming section about the data of each JOB.
C: LIMITATION DIGITS (for (−) key) = 0 to 7 (0 FIXED for [%n])
3. [Auto] key reading
(*3) MEDIA PROGRAM : ABC
A: Footer print on Receipt
A
No
0
Yes
1
B: Entry of amount tenderd
HEADER
DATE /TIME /CLERK NO
11/01/2003 12:34PM
123456#1234
B
Non compulsory (Cash, check),
Inhibit (Credit)
0
Compulsory
1
BETTY___
*PGM*
1
0
0
0
CA/AT
C: LIMITATION DIGITS (0 = INHIBIT) = 0 to 8
(*4) CONVERSION PROGRAM : AB
A: OPEN RATE ENTRY
------
MACHINE NO. /CC-NO. /
CLERK NAME
MODE TITLE
KEY TEXT
DELETE (NO KEY)
A
ENABLE
0
DISABLE
1
B: PRESET RATE ENTRY
01
4. Printer density report
B
ENABLE
0
DISABLE
1
HEADER
DATE /TIME /CLERK NO
11/01/2003 12:34PM
123456#1234
01
BETTY___
*PGM*
#50
50
10 : 0123456789AB
20 : 0123456789AB
30 : 0123456789AB
40 : 0123456789AB
50 : 0123456789AB
60 : 0123456789AB
70 : 0123456789AB
80 : 0123456789AB
90 : 0123456789AB
XE-A41S
PROGRAM MODE
2–2
MACHINE NO. /CC-NO. /
CLERK NAME
MODE TITLE
Thermal printer density
Printing Sample
(Light & Shade value between
10 to 90.)
5. PLU/UPC data report
2)
DEPT FUNCTION PROGRAMMING
0
ABCDEFGHIJK
HEADER
@/FOR
DPTn
DEPT SHIFT
11/01/2003 12:34PM
123456#1234
01
BETTY___
DATE /TIME /CLERK NO
0
MACHINE NO. /CC-NO. /CLERK NAME
YY
*PGM*
DEPT#
ABCDEFGHIJK
@/FOR
MODE TITLE
0001999999
(O1)
-1234.56
C0 1
P0001
PLU001xxxxxx
:
:
1234567890123#
1234567890123
(O1)
-1234.56
C0 1
:
:
START CODE (RANGE DATA)
END CODE (RANGE DATA)
PLU CODE /DEPT code
TEXT /PRICE WITH SIGN
COMMISSION GR. /Type(*1)
YY: Department code (01 to 99)
A: KINDS
UPC CODE /DEPT code
TEXT /PRICE WITH SIGN
COMMISSION GR. /Type(*1)
0
BOTTLE RETURN
1
★
C: Commission Group = 0 to 2
D: Taxable 4
-------
When PLU is deleted at the
programming JOB.
When PLU is deleted at the
programming JOB.
(*1) PROGRAM : Y
Y: PROGRAM
Y
SUBDEPT
0
PLU
1
0
Yes
1
0
Yes
1
1) PRICE PROGRAMMING FOR [DEPT.] & (−) KEYS
0
Yes
1
0
Yes
1
0
SICS
1
DEPT SHIFT
0
XXXXXX
(-)
I: SIGN
B
#/TM/SBTL
+
−
DEPT#
CA/AT/NS
★
DPTn
0
★
1
J: LIMITATION DIGITS = 0 to 7
YY: Department Code (01 to 99)
0 : OPEN PRICE REGISTRATION INHIBIT.
XXXXXX: Unit price (Max. 6digits)
If a price is set for a department which amount entry type is “INHIBIT” or
“OPEN”, its amount entry type is set as below automatically.
1
★
A
NORMAL
DPTn
XXXXXX
★
D
No
H: REGISTRATION TYPE
0
★
C
No
G: Taxable 1
★
B
No
F: Taxable 2
2. USER PROGRAMMING
A
No
E: Taxable 3
“PRESET”
A
NORMAL
B: Group = 0 to 9
NOTE :
The deleted PLU /UPC is not printed.
P0001
1234567890123#
YY
CA/AT/NS
DPTn
K: AMOUNT ENTRY TYPE
“INHIBIT”
“OPEN & PRESET” 1 “OPEN”
MRS = 0
D
Inhibited
0
Open
1
Preset
2
Open & Preset
3
★
MRS = 00000000071
(NORMAL, NON GROUP, NON TAXABLE, NORMAL, SIGN (+),
HALO = 7, OPEN)
(Dept 01-10 : Taxable1 = Yes, Dept11 - 99 : Non Taxable)
XE-A41S
PROGRAM MODE
2–3
3)
(-) & [%] KEY FUNCTION PROGRAMMING
5) PROGRAMMING FOR CONVERSION.
0
0
(-)
ABCDEFGH
@/FOR
CA/AT/NS
AB
%n
A: Taxable 4
A
No
0
Yes
1
B: Taxable 3
0
Yes
1
C: Taxable 2
0
Yes
1
D: Taxable 1
0
Yes
1
A
ENABLE
0
DISABLE
1
★
B
ENABLE
0
DISABLE
1
★
MRS = 00
★
6) PROGRAMMING FOR FUNCTION KEYS.
0
D
No
CA/AT/NS
B: PRESET RATE ENTRY
★
C
No
CLK#/CONV
A: OPEN RATE ENTRY
★
B
No
@/FOR
★
A
RA/AMT
@/FOR
RCPT/PO
CA/AT/NS
TAX
(for Manual-TAX)
E: SIGN
E
+
0
-
1
F: ENTRY FOR ITEM
A: LIMITATION DIGITS (0 = INHIBIT)
★
= 0 to 7 (for Manual TAX)
= 0 to 9 (for RA, PO)
F
ENABLE
0
DISABLE
1
★
MRS = 7 (Manual TAX), 9 (RA, PO)
7) PROGRAMMING FOR MEDIA KEYS.
G: ENTRY FOR SBTL
G
ENABLE
0
DISABLE
1
([#/ST] key is used for programming of CASH.)
★
0
ABC
H: LIMITATION DIGITS (for (−) key) = 0 to 7
CHK
@/FOR
CHn
CA/AT/NS
#/TM/SBTL
0 : • OPEN PRICE REGISTRATION INHIBIT (for (−) KEY).
(for CASH)
• FIXED for [%n]
MRS = 00001007
(NON-TAXABLE, MINUS SIGN, ITEM&SBTL, HALO = 7)
A: Footer print on Receipt
A
No
0
Yes
1
★
4) RATE PROGRAMMING FOR [%] KEY AND
CONVERSION KEY.
B: Entry of amount tenderd
0
%n
(RATE)
CA/AT/NS
CLK#/CONV
(RATE):
Noncompulsory (Cash, Check)/ Inhibit (Credit)
0
Compulsory
1
C: LIMITATION DIGITS (0 = INHIBIT) = 0 to 8
XXX.XX: Rate for % (0.00 to 100.00)
MRS = 008
XXXX.XXXX: Rate for EXCHANGE (0.0000 to 9999.9999)
The DECIMAL POINT must be entered for setting the decimal digits.
MRS = 0.00 (%n)
0.0000 (CONVERSION)
XE-A41S
PROGRAM MODE
2–4
B
★
8) DATA PROGRAMMING FOR PLU/UPC
11) PROGRAMMING OF DEPARTMENT TEXT
There are programmed by below key sequence.
The PLU code is increment antomatically when one programming data
of a PLU is set.
And it is operated continuously until depressing the [CA/AT/NS] key.
The JOB is antomatically finalized when a maximum PLU code is
programmed.
NO CHANGE
1
SBTL
(Basic programming sequence)
DPTn
DEPT SHIFT
DPTn
XX
DEPT CODE
DEPT#
SBTL
(CHARACTERS)
CA/AT/NS
XX: DEPT Code (1 to 99)
Basic operation consists of below 2 kinds.
(CHATACTERS): CHARCTER (Max. 16 Characters)
<Associate Dept & Price Entry>
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
(SCANNING)
XXXXXXXXXXXXX
PLU/UPC CODE
PLU/UPC
DPTn
(DATA)
DEPT SHIFT
) DEPT
CODE )
CA/AT/NS
DPTn
DEPT# (DATA) SBTL
YYY 3 [00] KEY
(Go to Next Code)
YYY: CHARACTER CODE (3 DIGITS)
(Code entry)
(or [000] KEY ACCORDING TO PGM PRESET)
<Parameter data Entry>
MRS = DEPT. xx (xx: DEPT Code)
(SCANNING)
XXXXXXXXXXXXX
PLU/UPC CODE
PLU/UPC
SBTL
(DATA)
CA/AT/NS
(Go to Next Code)
12) PROGRAMMING OF PLU/UPC TEXT
(Code entry)
(SCANNING)
9) PROGRAMMING OF DEPARTMENTS TO BE
ASSOCIATED WITH PRICE PRESET
SBTL
2
XXXXXXXXXXXXX
NO CHANGE
PLU/UPC
(CHARACTERS)
SBTL
CA/AT/NS
PLU/UPC CODE
(Code increment)
PLU/UPC DELETE
(SCANNING)
XXXXXXXXXXXXX
PLU/UPC CODE
(Code entry)
0
PLU/UPC
DPTn
YYYYYY
XXXXXXXXXXXXX: PLU CODE
CA/AT/NS
UPC (EAN) CODE
DEPT SHIFT DPTn
0
ZZ DEPT# YYYYYY
DEPT CODE
(Go to Next Code)
(Code entry)
XXXXXXXXXXXXX: PLU CODE
UPC (EAN) CODE
=
=
=
=
Max. 4digits (1 t o 9999)
Max. 13digits (EAN13,
EAN8, UPC-A, UPC-E)
(CHARACTERS): CHARACTER (Max. 16 Characters)
SBTL
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
Max. 4digits (1 t o 9999)
Max. 13digits (EAN13,
EAN8, UPC-A, UPC-E)
YYY3 [00] KEY
YYY: CHARACTER CODE (3 DIGITS)
ZZ: DEPT CODE (1 to 99)
(or [000] KEY ACCORDING TO PGM PRESET)
YYYYYY: UNIT PRICE (6 digits)
MRS = PLUxxxx (xxxx: PLU code)
MRS (UPC) = ALL SPACE
DELETE means to be set as a inhibited PLU in memory.
When it is assigned some DEPT for the inhibited (deleted) PLU,
the PLU is set the MRS value except its price.
MRS = DEPT1, Price: 0 (Create: PLU001 to PLU0020)
13) PROGRAMMING OF FUNCTION TEXT
NO CHANGE
10) PLU/UPC FUNCTION PROGRAMMING.
XXXXXXXXXXXXX
PLU/UPC CODE
SBTL
0
(SCANNING)
PLU/UPC
AB
SBTL
XX
@/FOR
(CHARACTERS)
SBTL
CA/AT/NS
CA/AT/NS
XX : FUNCTION CODE (Refer to the FUNCTION LIST)
(Code entry)
XXXXXXXXXXXXX: PLU CODE
UPC (EAN) CODE
=
=
(CHARACTERS) : CHARACTER (Max. 8 Characters)
Max. 4digits (1 t o 9999)
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
Max. 13digits (EAN13,
EAN8, UPC-A, UPC-E)
A: Commission Group = 0 to 2
B: PLU/SUB DEPT
3
YYY 3 [00] KEY
B
SUBDEPT
0
PLU
1
YYY: CHARACTER CODE (3 DIGITS)
★
( or [000] KEY ACCORDING TO PGM PRESET)
MRS = 01 (No Group, PLU type)
MRS
XE-A41S
= Refer to the following table
PROGRAM MODE
2–5
■ FUNCTION LIST
F-NO.
1
F-NO.
FUNCTION
(− )
DEFAULT
12345678
BOTTLE (+) DPT TOTAL
*BTTL TL
58
BOTTLE (−) DPT TOTAL
BTTL ( − )
SUBTOTAL
SUBTOTAL
57
(−)
DEFAULT
12345678
FUNCTION
2
%1
%1
59
3
%2
%2
60
MDS SBTL
MDSE ST
TOTAL
***TOTAL
CHANGE
4
NET1
NET1
61
5
TAXABLE1 ST
TAX1 ST
62
CHANGE
6
GROSS TAX1
GRS TAX1
63
ITEMS
ITEMS
7
REFUND TAX1
RFD TAX1
64
COMMISSION AMOUNT1
COM. AMT1
8
NET TAX1
TAX1
65
COMMISSION AMOUNT2
COM. AMT2
9
EXEMPT TAX1
TX1 EXPT
66
COMMISSION AMOUNT TOTAL
COM. TTL
10
TAXABLE2 ST
TAX2 ST
67
DEPT. REPO. TITLE
DEPT
11
GROSS TAX2
GRS TAX2
68
PLU/UPC REPO. TITLE
PLU/UPC
12
REFUND TAX2
RFD TAX2
69
TRANS. REPO. TITLE
TRANS.
13
NET TAX2
TAX2
70
CLERK REPO. TITLE
CLERK
HOURLY
14
EXEMPT TAX2
TX2 EXPT
71
HOURLY REPO. TITLE
15
TAXABLE3 ST
TAX3 ST
72
DAILY NET REPORT TITLE
DAILY
16
GROSS TAX3
GRS TAX3
73
GROUP REPORT TITLE
GROUP
17
REFUND TAX3
RFD TAX3
74
TL-ID REPORT TITLE
TL-ID
18
NET TAX3
TAX3
75
NON ADD CODE TEXT
#
19
EXEMPT TAX3
TX3 EXPT
76
COPY RECEIPT TITLE
COPY
20
TAXABLE4 ST
TAX4 ST
77
GROUP1
G ROUP01
21
GROSS TAX4
GRS TAX4
78
GROUP2
G ROUP02
22
REFUND TAX4
RFD TAX4
79
GROUP3
G ROUP03
23
NET TAX4
TAX4
80
GROUP4
G ROUP04
24
EXEMPT TAX4
TX4 EXPT
81
GROUP5
G ROUP05
25
GROSS M-TAX
GRS MTAX
82
GROUP6
G ROUP06
26
REFUND M-TAX
RFD MTAX
83
GROUP7
G ROUP07
M-TAX
84
GROUP8
G ROUP08
TTL TAX
85
GROUP9
G ROUP09
NET
86
DUE (for DISPLAY)
DUE
87
TAX ST (for DISPLAY ALL TAX DEL.)
TAX ST
27
28
29
NET M-TAX
TOTAL TAX
NET without TAX
30
NET2
NET2
31
REFUND
REFUND
32
VOID
VOID
33
VOID MODE
VO I D
34
MANAGER VOID
MGR VD
35
SBTL VOID
SBTL VD
36
NO SALE
NO S ALE
37
RA
***RA
14) PROGRAMMING OF LOGO TEXT
NO CHANGE
SBTL
PO
39
CUSTOMER
TRA NS CT
40
NET3 (SALES)
NET3
41
CASH
CASH
42
CHECK
CHECK
43
GROSS CHARGE1
CHARGE
44
REFUND CHARGE1
CHARGE -
45
GROSS CHARGE2
CHARGE2
46
REFUND CHARGE2
CHARGE2-
47
CONVERSION (PRESET RATE)
CONV 1
X
@/FOR
(CHARACTERS)
X: LINE NO. (1 to 6)
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
YYY3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
(Sample)
CONVERSION (OPEN RATE)
CONV 2
49
CASH IN DRAWER
****C ID
SHARP
PRESENTS THE
50
CASH+CHECK IN DRAWER
CA+ CH ID
CHECK CHANGE
CHK / CG
52
COMMISSION SALE1
COM. SAL1
53
COMMISSION SALE2
COM. SAL2
54
NON COMMISSION SALE
NON COM.
55
(+) DEPT TOTAL
*DEPT TL
56
(−) DEPT TOTAL
MRS =
DEPT ( − )
XE-A41S
CA/AT/NS
(CHARACTERS): CHARACTER (Max. 24 Characters)
48
51
SBTL
LINE NO.
***PO
38
4
PROGRAM MODE
2–6
BEST ECR
SHARP
IS
THE BEST
15) PROGRAMMING OF CLERK NAME
A: INTERVAL BETWEEN BREAKPOINTS
NO CHANGE
SBTL
5
XX
@/FOR
(CHARACTERS)
SBTL
A
BELOW 1 DOLLAR
0
1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR
1
CA/AT/NS
B: TAX TABLE No.
XX: CLERK NO. (1 to 40)
(CHARACTERS): CHARACTER (Max. 8 Characters)
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
1
TABLE2
2
TABLE3
3
TABLE4
4
TAX RATE : 0.0001 to 99.9999
YYY3 [00] KEY
CYCLE : 1 to 9999
YYY : CHARACTER CODE (3 DIGITS)
INITIAL TAX : 1 to 999
(or [000] KEY ACCORDING TO PGM PRESET)
LOWER TAX LIMIT : 1 to 99999
MRS = CLERKxx (xx: clerk no.)
BREAK POINT : 1 to 99999
MRS = NO TAX
16) FOREIGN CURRENCY SYMBOL PROGRAMMING
18) TAX RATE PROGRAMMING
NO CHANGE
SBTL
6
B
TABLE1
SBTL
(CHARACTERS)
CA/AT/NS
(Inhibition programming)
(CHARACTERS): CHARACTER (Max. 4 Characters)
0
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
SBTL
9
@/FOR
A
TAX NO.
@/FOR
xxx.xxxx
TAX RATE
0
YYY3 [00] KEY
@/FOR
xxxxx
LOWER TAX LIMIT
FOR ADD TAX
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
MRS = ____
( _ : space code)
SBTL
Note: This symbol is printed as the amount of CURRENCY CONVERSION for PRESET RATE only.
The amount symbol of CURRENCY CONVERSION for OPEN
RATE is not printed.
A : TAX 1 PROGRAMMING
1
TAX 2 PROGRAMMING
2
TAX 3 PROGRAMMING
3
TAX 4 PROGRAMMING
4
17) TAX TABLE PROGRAMMING
SBTL
8
AB
@/FOR
xx.xxxx
@/FOR
DECLARATION
OF TAX
% TAX RATE
RATE xxx.xxxx = 0.0000 to 100.0000 %
@/FOR
TAX RATE
LOWER TAX LIMITATION 0.00 to 999.99
(This is invalid in VAT system.)
(Table Delete programming)
MRS = DELETE
*
xxxx
CYCLE
@/FOR
xxx
INITIAL TAX
CA/AT/NS
@/FOR
19) COMMISSION RATE PROGRAMMING
0
(Table Delete programming)
SBTL
28
xxxxx
LOWER TAX LIMIT
@/FOR
xxxxx
@/FOR
@/FOR
A
@/FOR
XXX.XX
SBTL
CA/AT/NS
COMMISSION No.
SBTL
CA/AT/NS
A : COMMISSION NO. (1 or 2)
BREAK POINT
XXX.XX : COMMISSION RATE (0.00 to 999.99)
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAXTABLE.
(Case of interval between break point is 1 dollar or more and less than
100 dollar, 36 breakpoints is programmed for each table.)
The DECIMAL POINT must be entered for setting the decimal digits.
MRS = 0.00 (%)
* DEPRESSION OF THE [SBTL] KEY AT THE FOLLOWING POINTS
MEANS A TAX TABLE DELETE OPERATION.
XE-A41S
PROGRAM MODE
2–7
20) RATE HALO PROGRAMMING FOR [%] KEY
23) VARIOUS PROGRAMMING
(EACH FUNCTIONS PROGRAMMING)
0
SBTL
29
@/FOR
%n
XXX.XX
There are programmed by depressing ST-key after a data that want to
set. And it is operated continuously until depressing the TL-key
CA/AT/NS
(Programming sequence)
0
XXX.XX: % HALO (0.00 to 100.00)
SBTL
The DECIMAL POINT must be entered for setting the decimal digits.
MRS = 100.00 (%)
AB
@/FOR
(NK)
SBTL
CA/AT/NS
AB : JOB No.
NK : PROGRAMMING DATA. (Numeric Keys)
21) [AUTO] KEY PROGRAMMING
[JOB#1] MACHINE No. (6digits)
max 25
-- XXXXXX --
MRS = 000000
AUTO
AUTO
(Free key)
CA/AT/NS
[JOB#2] CONSECUTIVE No. (4digits)
Delete
-- XXXX --
MRS = 0000
It must be pushed same [AUTO] key as the programming [AUTO] key at
the end of any key entry.
[JOB#5] FUNCTION SELECT
-- ABCDEFGH --
MRS = 00000001
Note: [ESC] key cannot be set at [AUTO] key programming.
It acts as a key of ERROR ESCAPE function in this programming.
A: PO in REG mode
< [Auto] key function >
This machine has [AUTO] key which can be programmed the
key-sequence data.
When [AUTO] key is depressed, the machine works as same as the
programmed key-sequence is entered.
A
ENABLE
0
DISABLE
1
B: RA in REG mode
★
B
ENABLE
0
DISABLE
1
★
Executing mode : REG, MGR, OPXZ, X1/Z1, X2/Z2
C: SUBTOTAL VOID in REG mode
Setting mode : PGM
22) DATE, TIME PROGRAMMING
XXXXXXXX
DATE
HHMM
TIME
1
(MM
: 01 to 12)
(DD
: 01 to 31)
0
DISABLE
1
The date entry format complies with the applicable PGM-mode
programming.
0
DISABLE
1
HH: Hour (00 to 23)
MM: Minute (00 to 59)
0
DISABLE
1
MRS = DATE : 01012000 (DD/MM/YYYY)
TIME : 0000
XE-A41S
PROGRAM MODE
2–8
★
G
ENABLE
0
DISABLE
1
H: FRACTIONAL QUANTITY
Note: It cannot set the non-exist date (like Feb. - 30th)
★
F
ENABLE
G: NO SALE in REG mode
★
E
ENABLE
F: REFUND in REG mode
(YYYY: 2000 to 2099)
★
D
ENABLE
E: DIRECT VOID in REG mode
DATE) XXXXXXXX: YYYYMMDD (Year - month - Day) or
DDMMYYYY (Day - month - Year) or
MMDDYYYY (Month - day - Year)
TIME)
0
DISABLE
D: INDIRECT VOID in REG mode
#/TM/SBTL
C
ENABLE
★
H
YES (3digits decimal place)
0
NO
1
★
[JOB#6] PRINT FORMAT
-- ABCDEFGH --
[JOB#11] LOGO PRINTING
-- A --
MRS = 1
MRS = 00000011
A, B: Not used (Fixed at “00”)
A: LOGO MESSAGE CONTROL
C: TIME PRINTING (for all receipt)
C
PRINT
0
NOT PRINT
1
D: DATE PRINTING (for all receipt)
★
D
PRINT
0
NOT PRINT
1
E: CONSECUTIVE NO. PRINTING
★
0
NOT PRINT
1
★
0
SKIP
1
GRAPHIC LOGO AND 3-LINE FOOTER
2
6-LINE HEADER
3
GRAPHIC LOGO AND 3-LINE HEADER
4
3-LINE HEADER AND 3-LINE FOOTER
5
G
ENABLE
0
DISABLE
1
H: MANUAL TAX in REG mode
★
0
DISABLE
1
[JOB#16] UPC/EAN FUNCTION
NOT SKIP
0
MRS = 00000000
A, B: Not used (Fixed at “00”)
SKIP
1
★
-- ABCDEFGH --
MRS = 00000000
A, B: Not used (Fixed at “00”)
C
NOT PRINT
0
PRINT
1
D: MDSE SBTL PRINT AT [MDSE ST] KEY
★
0
PRINT
1
★
1
H: PURCHASE NO. PRINTING
H
PRINT
0
NOT PRINT
1
0
YES
1
Y
0
No (Disable)
1
E
YES
0
NO
1
★
F
COMPULSORY
0
INHIBITTED
1
G: P L U / U P C ( E A N ) P R I C E L O O K U P AT
REFUND ENTRY
MRS = 0030
Yes (Enable)
★
★
★
-- YXXX --
Y: POWER SAVING function when a time is displayed
★
D
NO
F: PRICE ENTRY after ISBN or ISSN
E, F, G: Not used (Fixed at “000”)
[JOB#10] POWER SAVING
0
YES
E: LERNING FUNCTION of UPC (EAN) ENTRY
D
NOT PRINT
C
NO
D: DEPT/PLU/UPC (EAN) code printing on receipt
C: SUBTOTAL PRINT [AT] [ST] KEY
★
-- ABCDEFGH --
C: DEPT/PLU/UPC (EAN) code printing on journal
[JOB#7] RECEIPT PRINT FORMAT
★
H
ENABLE
H
H: ZERO SKIP IN GENERAL,CLERK,HOURLY,
DAILY REPORT
★
-- ABCDEFGH --
G: TAX DELETE in REG mode
G
NOT SKIP
1
MRS = 000000000
A, B, C, D, E, F: Not used (Fixed at “000000”)
F: Not used (Fixed at “0”)
G: ZERO SKIP IN PLU/UPC REPORT
0
GRAPHIC LOGO ONLY
[JOB#15] FUNCTION SELECT2
E
PRINT
A
3-LINE HEADER INSTEAD OF GRAPHIC LOGO
XXX: POWER SAVING TIME to POWER OFF
= 001 to 254 (minutes)
or 999 (Inhibit)
XE-A41S
YES
0
NO
1
H: C/D check of UPC (EAN)
★
PROGRAM MODE
2–9
G
★
H
NO
0
YES
1
★
[JOB#20] SENTINEL (CID HALO)
-- XXXXXXXXX --
[JOB#62] OTHERS2 PROGRAMMING -- ABCDEFGH --
MRS = 999999999
MRS = 00000000
XXXXXXXXX : SENTINEL AMOUNT (9digits)
A: Not used (Fixed at “0”)
[JOB#35] ONLINE COMMUNICATION TIME OUT -- XXX --
B: ERROR BEEP for missoperation
B
MRS = 007
LOCK ERROR
0
XXX: Time out time (1 to 255 sec)
MISSOPERATION
1
Note: The device of ONLINE COMMUNICATION is USB Device only.
C: Key catch sound
[JOB#50] THERMAL PRINTER DENSITY CONTROL -- XX -MRS = 50
00 : 70 % for standard
50 : 100 % (Standard density)
99 : 130 % for standard
[JOB#61] OTHERS1 PROGRAMMING
MRS = 00100002
No
1
C: Programming of MINUS dept/PLU/UPC
C
Disable
0
Enable
1
0
No
1
D: Fractional treatment
D
Round off (4-DOWN, 5-UP)
0
Raising to unit
1
Disregarding
2
E: [00] key or [000] key selection for [00] key position
★
0
Disable
1
★
F
Yes
0
No
1
★
G
Yes
0
No
1
H: Addition to the hourly total in VOID MODE
★
E
Enable
G: Printing of VOID MODE in Z1 report
★
★
D
Yes
F: Printing of VOID MODE in Z2 report
A, B: Not used (Fixed at “00”)
★
H
No
0
Yes
1
★
E
[00] key
0
[000] key
1
F: Time format
F
12hour
0
24hour
1
G: Date format
0
E: VOID mode
-- ABCDEFGH --
C
Yes
D: Buffered Keyboard
XX: density (00 to 99)
★
★
[JOB#63] OTHERS3 PROGRAMMING -- ABCDEFGH -MRS = 01000001
A: Receipting at the time of NO SALE
★
G
M-D-Y
0
D-M-Y
1
Y-M-D
2
0
No
1
B: NO SALE after non-add code entry
★
A
Yes
B
Disable
0
Enable
1
C: NON-ADD code entry
H
Enable
0
0
0
Disable
1
1
1
2
2
3
3
D: Copy Receipt
XE-A41S
PROGRAM MODE
2 – 10
★
D
No
0
Yes
1
E: Entry that causes the merchandise SUBTOTAL
to be smaller than zero.
★
C
H: TAB
★
★
★
E
Enable
0
Disable
1
★
F: Subtotal entry before tendering
[JOB#66] OTHERS6 PROGRAMMING -- ABCDEFGH --
F
Noncompulsory
0
Compulsory
1
G: Subtotal entry before direct non-tender finalization
★
MRS = 10000000
A: AFTER-TRANSACTION RECEIPT
G
Noncompulsory
0
Compulsory
1
★
A
TOTAL ONLY
0
DETAILS
1
B: AMOUNT PRINTING WHEN PLU UNIT PRICE IS 0
H: Direct non-tender finalization after tendering
B
H
No
0
Disable
0
Yes
1
Enable
1
★
★
C: CONVERSION SBTL PRINTING OF NATIVE SBTL
C
[JOB#64] OTHERS4 PROGRAMMING -- ABCDEFGH --
Yes
0
MRS = 00000000
A: Printing of GT1 on Z report
No
1
★
A
Yes
0
No
1
D, E, F: Not used (Fixed at “000”)
★
G: Logo Text Print on Journal
B: Printing of GT2 on Z report
B
Yes
0
No
1
C: Printing of GT3 on Z report
★
0
No
1
D: Printing of Training GT on Z report
G
No
0
Yes
1
H: FOOTER PRINT CONTROL
C
Yes
★
★
H
ALL RECEIPTS
0
ON SELECTED FUNCTION KEY AT THE TIME
OF FINALIZATION
1
★
D
Yes
0
No
1
E: Printing of Z counter on Z report
★
[JOB#67] OTHERS7 PROGRAMMING -- ABCDEFGH -MRS = 00000000
A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)
E
Yes
0
No
1
F: Printing of DATA on PLU/UPC resetting report
★
[JOB#68] OTHERS8 PROGRAMMING
-- ABCDEFGH --
MRS = 00000000
A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)
F
★
Yes
0
No
1
[JOB#69] OTHERS9 PROGRAMMING -- ABCDEFGH --
G
MRS = 00100000
A, B: Not used (Fixed at “00”)
G: Reset GT1, 2, 3 at the general Z1 report
No
0
Yes
1
H: OP X/Z report
★
C: ECR data copy BAUD RATE (BPS)
H
Enable
0
Disable
1
[JOB#65] OTHERS5 PROGRAMMING
★
★
C
9600
0
19200
1
★
D, E: Not used (Fixed at “00”)
F: TAX PRINTING WHEN TAXABLE SUBTOTAL
IS ZERO
-- ABCDEFGH --
MRS = 00000000
A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)
No
0
Yes
1
G: TAX PRINTING WHEN TAX IS ZERO
PROGRAM MODE
2 – 11
★
G
Yes
0
No
1
H: Not used (Fixed at “0”)
XE-A41S
F
★
[JOB#70] OTHERS10 PROGRAMMING -- ABCDEFGH --
25) TRAINING MODE TEXT PROGRAMMING
MRS = 00000000
NO CHANGE
A: SPLIT PRICING COUNTING
SBTL
A
QUANTITY
0
PACKAGE
1
B: MULTIPLICATION ENTRY SYSTEM
0
SPLIT PRICING & MULTIPLICATION
1
SBTL
(CHARACTERS)
CA/AT/NS
★
(CHARACTERS): CHARACTER (Max. 8 characters)
★
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
B
MULTIPLICATION ONLY
87
YYY 3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
C, D, E, F, G, H: Not used (Fixed at “000000”)
MRS = TRAINING
[JOB#71] GT2 PROGRAMMING -- XXXXXXXXXXXXX -MRS = 0000000000000
26) TEXT CHANGING (TO DEFAULT TEXT)
XXXXXXXXXXXXX : GT (13digits)
0
[JOB#72] GT3 PROGRAMMING -- XXXXXXXXXXXXX --
SBTL
MRS = 0000000000000
88
@/FOR
X
CA/AT/NS
X: 0 = English text
3 = Spanish text
XXXXXXXXXXXXX : GT (13digits)
MRS = 0
[JOB#76] GENERAL Z1 RESET REPORT COUNTER -- XXXX -MRS = 0000
When this job is executed, below texts are set as default data.
XXXX : RESET COUNTER (4digits)
(a) Function text
(b) Each message text (LOGO, etc..)
[JOB#77] GENERAL Z2 RESET REPORT COUNTER
-- XXXX --
MRS = 0000
XXXX : RESET COUNTER (4digits)
HEADER
[JOB#86] TRAINING CLERK PROGRAMMING
11/01/2003 12:34PM
-- XX --
MRS = 00
123456#1234
X : CLERK No. = 0 (INHIBIT), 1 to 40
*PGM*
01
BETTY___
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
MODE TITLE
0
#88
LANGUAGE MODE
24) DOMESTIC CURRENCY SYMBOL PROGRAMMING
NO CHANGE
SBTL
85
(CHARACTERS)
SBTL
CA/AT/NS
27) RESETTING OF ALL COUNTER AND TOTALIZER
(CHARACTERS): CHARACTER (Max. 4 Characters)
Characters can be entered by using the character layout on keyboard or
using numeric keys on keyboard.
THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER
BY NUMERIC KEYS IS AS FOLLOWS:
SBTL
89
@/FOR
CA/AT/NS
All counter, totalizer, all GTs, and all Z counter are reset.
YYY 3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
MRS = ___$ ( _ : space code)
HEADER
This symbol is printed with (+) amount of domestic currency.
The programmed characters is printed at left side of amount.
11/01/2003 12:34PM
123456#1234
Ex) Case of " US$ ":
| DEPT.01
US$1.00 |
2
Programmed symbol
MACHINE NO. /CC-NO. /CLERK NAME
MODE TITLE
#89
JOB#
Ex) Case of “ US$”: (The currency symbol means “US$”)
|AAAADEPARTMENT01 US$10000.00 |
2
Programmed symbol
PROGRAM MODE
2 – 12
DATE/TIME/CLERK NO
*PGM*
If some space characters are programmed at the left side of symbol
(like “ $”), they are not counted as the number of character of the currency symbol. (In case of “ US$”, the number of character is 3.)
XE-A41S
01
BETTY___
[JOB#141] Programming data saving to SD CARD
[JOB#147] Programming data loading from SD CARD
28) MAXIMUM NUMBER OF DEPARTMENT
SBTL
95
@/FOR
XX
CA/AT/NS
The below data is saved or loaded.
Files are set in the folder for “Programming Data”.
XX : Max Number of DEPARTMENT (01 to 99)
This job is used for the limitation of below functions.
File Name
(1) Programming for the department code over the maximum number of department.
File/Table
No. (*1)
1 Date and Time mtimtbl
D0
2 Others
Programming
mopttbl
D1
(3) Registration for the PLU that is associated to department over
the maximum number of department.
3 Tax Table and
Rate
mtaxtbl
D7
(4) Printing for the department data over the maximum number of
department at PGM READING and XZ REPORTS.
4 Logo message mlgxtbl
D2
(2) Registration for the department code over the maximum number of department.
MRS = 99
5 Function
programming
FuncText
A4
Mfunctbl
D8
6 Department
deptdata
01
B000
(Label, Preset, Price, Text)
7 PLU/UPC
pludata
11
B000
(Label, Preset, Price, Text)
8 Clerk
CsrData
51
1000 (Label. Text)
29) SD CARD FUNCTION
[Key Sequence of SD Jobs]
SBTL
xxx
@/FOR
SBTL
(*1)
1
(*2)
CA/AT/NS : Execute operation (*3)
CL
: Cancel
Field (*1)
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted
to use at “Customer Support Tool” software on PC.
Notes: • If the folder for “Programming Data” dose not exist in SD
memory card, this job is inhibited. [FILE ACCESS ERROR]
(The SD memory card is not formatted by ECR.)
• If there is data of the same file name, the message of confirmation does not display.
Data is overwritten if there is data of the same file name.
xxx : JOB code
140 : Format SD CARD
141 : Save Programming Data (ECR 3 SD)
144 : Save All RAM Data (ECR 3 SD)
145 : Load Graphic Logo Data (ECR 1 SD)
147 : Load Programming Data (ECR 1 SD)
148 : Load All RAM Data (ECR 1 SD)
• Each files are used only for the “Customer Support Tool” software on PC. Any users dose not need to concern its contents.
(*1) When [SBTL] key is pushed, ECR prints the confirmation message
at “RECEIPT” (not print at JOURNAL) and enforces to select either
executing or canceling this job. The buffered keys are cleared.
[JOB#145] Graphic logo data loading
(*2) “1” is a keyword to execute this job.
The below data is loaded. Files are set in the folder for “LOGO Data”.
(*3) If the MODE SWITCH is turned to another mode from PGM position
or the AC POWER is off when job is executed, the job is cancelled.
File Name
Note: If AC POWER is off when ECR accesses SD CRAD, the contents in SD CARD may be broken.
The action of each job is as below.
[JOB#140] Format SD CARD
This job formats SD card. (It deletes all data on SD card.)
After formatting card, the folder \SHARP\ECRXXX01 is made to a root
directory.
And then, \ALL, \PROGRAM, \SALES, \EJPRINT, \EJ and \LOGO are
made to a folder “\SHARP\ECRXXX01”.
The file “SRECORD.REC” is made to both folder
“\SHARP\ECRXXX01\SALES“and”\SHARP\ECRXXX01\EJ”
and it is set the default data.
Notes: • All the data currently written in SD card is erased.
1 Graphic LOGO LOGO
File/Table
No. (*1)
Field (*1)
E0
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted
to use at “Customer Support Tool” software on PC.
Note: Files are created only for the “Customer Support Tool” software
on PC. Any users dose not need to concern its contents.
[JOB#144] All Data Saving
[JOB#148] All Data Loading
Notes: • In case of “DATA SAVING”, the message of confirmation for
overwritten the file on SD Card does not display. Data is overwritten if there is data of the same file name.
• In case of “DATA LOADING”, the condition of ECR will return
to past condition. However, the message of confirmation for
overwritten does not display.
• The file “SRECORD.REC” is used for control the structure
under each folder.Any users dose not need to concern its
contents.
The below data is saved or loaded. Files are set in the folder for “ALL
RAM BACKUP”.
File Name
1 All RAM data
All
Note: Each files are used only for the purpose of DATA BACKUP at
ECR. Any users dose not need to concern its contents.
XE-A41S
PROGRAM MODE
2 – 13
■ DISPLAY AND PRINT:
Key
OPERATION
Print
1 23 45 67 89 01 23 45 6
123456789012345678901234
[#/TM/STBL]
PGM
0
141 [@/FOR]
PGM
141
[#/TM/SBTL]
ARE YOU EXECUTE?
0
[1]
ARE YOU EXECUTE?
1
[CA/AT/NS]
ACCESSING CARD
NOTE
Numeric entry
(PRE-PRINT HEADDER)
!!!!!!!!!!!!!!!!!!!!!!!!
YOU SELECT SD CARD JOB
[1]-[CA/AT]KEY : EXECUTE
[CL]-KEY :
CANCEL
!!!!!!!!!!!!!!!!!!!!!!!!
Don't turn the mode key
while executing a job.
!!!!!!!!!!!!!!!!!!!!!!!!
(Issuing Receipt)
MESSAGE : MAX 8-lines
(The message is fixed in ROM.)
(Not count up CC# at this time.)
(Count up CC#.)
DISPLAY : ■ : Blinking while executing job.
(HEADER)
■
The buffered keys are cleared and the message is printed on
“receipt” only.
05/02/2006 12:34PM
01
123456#1234 BETTY___
PRINT
*PGM*
: JOB HEADDER is printed. And job code is printed.
(Job code is printed only at SD jobs)
#141
DISPLAY : ■ : Blinking while executing job.
PRINT : (NON)
(SD ACCESS)
Case of NORMAL END
Case of ERROR END
(No Card)
NO CARD
PGM SD FINAL
0. 00
(Issuing Receipt)
DISPLAY : Initial Display
PRINT : STATUS is printed (The message is fixed in ROM.)
PGM NO CARD
0. 00
(Issuing Receipt)
DISPLAY : ERROR MESSAGE (Refer to list of “ERROR MESSAGE”)
PRINT : ERROR MESSAGE (The message is fixed in ROM.)
Case of ERROR END
(ACCESS ERROR)
ACCESS ERROR
Case of CHANGING
MODE KEY (To cancel)
SD CANCEL
Case of POWER OFF
(Issuing Receipt)
ERROR MESSAGE
(Refer to list of “ERROR MESSAGE”)
(The message is fixed in ROM)
PRINT
: SD CANCEL MESSAGE (The message is fixed in ROM.)
(Issuing Receipt)
POWER OFF
PGM
0. 00
POWER OFF ERROR
AT THE DEVICE CONTROL
SET DATA&TIME AGAIN
DISPLAY : ERROR MESSAGE (Refer to list of “ERROR MESSAGE”)
PRINT : MESSAGE of POWER OFF (The message is fixed in ROM.)
(Issuing Receipt)
The message are printed on both RECIPT and JOURNAL.
XE-A41S
PROGRAM MODE
2 – 14
4. CHARACTER ASSIGNMENT METHOD
■ PROGRAMMING KEY LAYOUT
[XE-A41S]
RECEIPT JOURNAL
RA
/AMT
RCPT
/PO
-
@/FOR
%1
%2
NUMBER
VOID RFND
DC
SHIFT
ESC
/HELP
BS
SPACE
7
.
8
4
5
1
2
0
CL
9
6
PLU
/SUB
DEPT
#
25
30
5
A
10
24
4
B
C
9
2
00
1
D
8
G
H
7
I
14
J
20
L
13
M
19
N
18
O
R
37
17
31
11
Q
38
32
12
P
39
33
26
6
K
40
34
27
21
E
15
28
22
3
35
29
23
3
F
DEPT CLK#
SHIFT /CONV
S
36
16
T
INQ AUTO
U
X
TAX1
SHIFT
TAX2
SHIFT
V
Y
TAX CH1
W
Z
CHK CH2
MDSE #/TM
SBTL SBTL
CA/AT/NS
Note: The small characters on the bottom or lower right in each key indications or characters which can be used for character entries for text programming.
■ THE METHOD OF CHARACTER ENTRY AT TEXT PROGRAMMING
The character can be entered by using character key or character code.
When the character can be entered in the text programming, the key layout is changed from “Function and [DEPT] key layout” to “CHARACTER KEY
LAYOUT”.
In “CHARACTER KEY LAYOUT”, any key except the Numeric keys and [CL], [#/TM/SBTL], [CA/AT/NS] are assigned either the character or the control key for character entry.
Any character can be entered by following mathod.
By character key:
SHIFT
(CHARACTER KEY)
: Characters on Character key layout.
NUMBER
(NUMERIC KEY)
: Numeric character ("0", "1", . . . , "9")
By Numeric key (Character Code) :
xxx
[00]
xxx : Character Code
(The list of Control Key)
Key
SHIFT
Action
Entry to shift the following character key. (ex. [SHIFT] 3 [A] : Enter the character “a”.)
NUMBER Entry the following numeric key as the number character. (ex. [NUMBER] 3 [1] : Enter the character “1”.)
(DC)
Double size character: Change the following character to the double size character.
BS
Back Space : Delete the last character.
The status of [SHIFT], [NUMBER] and [DC] are keeping until pushing same control key in each text entry. (STAY DOWN type)
And the corresponding indication is lighted up on the display while their status is “on”.
(Example)
[SHIFT] 3 [A] [B] [C] 3 [SHIFT] 3 [A] [B] [C]
: Text “abcABC”.
[NUMBER] 3 [1] [2] [3] 3 [NUMBER] 3 [1] [2] [3] : Text “123” and numeric number 123.
[DC] 3 [A] [B] [C] 3 [(DC)] 3 [A] [B] [C]
: Text “ABCABC”.
XE-A41S
PROGRAM MODE
2 – 15
<Character Code Table for text programming> Printer
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
CHARACTER
CODE
001
á
049
1
098
b
147
ù
196
002
â
050
2
099
c
148
à
197
003
ê
051
3
100
d
149
Æ
198
004
î
052
4
101
e
150
φ
199
ì
053
5
102
f
151
Å
200
í
054
6
103
g
152
¤
201
007
ô
055
7
104
h
153
é
202
008
ó
056
8
105
i
154
è
203
û
057
9
106
j
155
Pt
204
ú
058
:
107
k
156
¡
205
059
;
108
l
157
Ñ
206
060
<
109
m
158
Õ
207
061
=
110
n
159
£
208
062
>
111
o
160
¥
209
063
?
112
p
161
210
Λ
064
@
113
q
162
211
017
Ψ
065
A
114
r
163
212
018
066
B
115
s
164
019
Γ
..
067
C
116
t
165
Ω
D
117
u
166
T
020
068
∆
E
118
v
167
T
021
069
Θ
F
119
w
168
T
022
070
023
Ξ
CODE
005
006
009
010
011
œ
012
013
ú
014
015
016
ó
024
Π
025
Σ
026
Υ
027
Φ
028
029
Ú
030
CHARACTER
P
š
213
.
071
G
120
x
169
T
072
H
121
y
170
1
073
I
122
z
171
1
074
J
123
{
172
1
075
K
124
|
173
2
076
L
125
}
174
2
077
M
126
ß
175
3
078
N
127
079
O
128
!!
177
080
P
129
1
081
Q
130
082
R
083
214
1
215
2
216
3
217
4
218
2
219
3
220
4
221
3
222
4
223
4
224
176
*
225
§
226
Ø
178
227
^
2
179
228
2
131
3
180
A
229
]
S
132
4
181
a
230
[
182
E
231
Á
031
Ó
032
(Space)
033
!
034
"
035
#
084
T
133
1
036
$
085
U
134
F
T
183
e
232
ä
037
%
086
V
135
1
184
I
233
ö
038
&
087
W
136
3
185
i
234
ü
039
'
088
X
137
p
186
U
235
æ
040
(
089
Y
138
p
187
u
236
å
041
)
090
Z
139
d
188
237
É
042
*
091
Ä
140
e
189
238
ñ
043
+
092
Ö
141
F
190
044
,
093
Ü
142
T
191
045
–
094
^
143
4
192
046
.
095
_
144
ç
193
047
/
096
145
O
194
048
0
097
146
¿
195
253
(DC)
a
/2
Note: The character of this table is for reference.Please see actual display.
(DC)
: Double Code
: ECR Control Character (Not used for text)
XE-A41S
PROGRAM MODE
2 – 16
Š
5. HELP FUNCTION
This function prints guidance messages of main cash register functions
by pushing the HELP key. If you push a number key and the HELP key
following the guidance messages, more detailed guidance messages
will be printed.
If [HELP] key is pressed on the ECR, the following receipt is printed.
HEADER
[PURPOSE]
The aim is to be able to easily program the register by printing the guidance messages.
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
HELP MENU
MODE TITLE
1-[HELP]:
2-[HELP]:
3-[HELP]:
4-[HELP]:
5-[HELP]:
6-[HELP]:
7-[HELP]:
DATE/TIME
TAX
DEPARTMENT
SALES Z REPORT
LOGO
RECEIPT
"NOT ASSIGNED"
IN THE DISPLAY
8-[HELP]: SD CARD
9-[HELP]: PC S/W INSTALL
-----------------------OTHER ISSUE: PLEASE CALL
1-800-BE-SHARP
[PROGRAMMING]
(REG/MGR-mode)
Even if ECR is in a receipt-off state, HELP printing is executed.
[OPERATION]
1. Available Mode of Help function
PGM, VOID, O/P X/Z, REG, MGR, X1/Z1, X2/Z2
2. The proper timing of when the HELP function will work is when the
transaction is finalized, not during the transaction operation.
Key operating sequences
1-[HELP]: DATE/TIME
Help Menu
X
HELP
Help No.
HEADER
<Help Menu>
key
[HELP]
No.
Print menu
1
Date/Time setup
2
Rate of TAX setup
3
Department setup
4
Sales Z report
5
Logo setting
6
Receipt issue
7
What is “NOT ASSIGNED” in the display
8
SD card command
9
Install PC software
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
1 DATE/TIME SETUP
MODE TITLE
(PGM MODE)
DATE:XXXXXXXX-[SBTL]
YYYYMMDD OR
MMDDYYYY OR
MMDDYYYY(DEFAULT)
TIME:HHMM-[SBTL]
(0000-2359)
EX) 08/01/2006 PM4:30
(DATE FORMAT=M-D-Y)
08012006-[SBTL]
1630-[SBTL]
XE-A41S
PROGRAM MODE
2 – 17
2-[HELP]: TAX
4-[HELP]: SALES Z REPORT
HEADER
HEADER
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
2 TAX RATE SETUP
MODE TITLE
(PGM MODE)
[SBTL]-9-[@]-N-[@]-R[@]-Q-[SBTL]-[CA]
N:TAX NUMBER (1-4)
R:RATE(0.0000-100.0000%)
Q:MIN. TAXABLE AMOUNT
(0.00-999.99)
EX) TAX1(RATE=6.25%),
MIN. AMT=$3.00
[SBTL]-9-[@]-1-[@]-6.25
-[@]-300-[SBTL]-[CA]
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
4 SALES Z REPORT
MODE TITLE
SALES Z REPORT SHOWS THE
DAILY/ PERIODIC SALES
1. DAILY Z REPORT
(X1/Z1 MODE)
[.]-[CA]: GENERAL
[.]-[PLU]: PLU
[.]-[CLK#]: CLERK
[.]-[SBTL]: HOURLY
2. PERIODIC Z REPORT
(X2/Z2 MODE)
[.]-[CA]: GENERAL
[.]-[PLU]: PLU
[.]-[CLK#]: CLERK
[.]-[SBTL]: DAILY NET
3-[HELP]: DEPARTMENT
5-[HELP]: LOGO
HEADER
HEADER
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
3 DEPARTMENT PRICE&TEXT
MODE TITLE
(PGM MODE)
1)PRICE
XX-[DEPT#]-YYYYYY[SBTL]-[CA]
XX:DEPARTMENT CODE(1-99)
YYYYYY:UNIT PRICE
(MAX.6DIGITS)
2)TEXT
[SBTL]-1-[.]-XX-[DEPT#](TEXT)-[SBTL]-[CA]
XX:DEPARTMENT CODE(1-99)
TEXT CAN BE ENTERED BY
USING THE CHARACTER
LAYOUT ON KEYBOARD OR
NUMERIC KEY ON KEYBOARD.
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
5 LOGO SETTING
MODE TITLE
(PGM MODE)
1)LOGO FORMAT
[SBTL]-11-[@]-A-[SBTL][CA]
A=0:3LINE HEADER
1:GRAPHIC LOGO ONLY
2:GRAPHIC+3LINE FOOTER
3:6LINE HEADER
4:GRAPHIC+3LINE HEADER
5:3LINE HEADER/FOOTER
2)LOGO TEXT
[SBTL]-4-[.]-L-[@](TEXT)-[SBTL]-[CA]
L:LINE NUMBER(1-6)
TEXT CAN BE ENTERED BY
USING THE CHARACTER
LAYOUT ON KEYBOARD OR
NUMERIC KEY ON KEYBOARD.
3)GRAPHIC LOGO
PLEASE REFER TO
CUSTOMER SUPPORT TOOL
XE-A41S
PROGRAM MODE
2 – 18
6-[HELP]: RECEIPT
9-[HELP]: PC S/W INSTALL
HEADER
HEADER
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
6 RECEIPT ISSUE
MODE TITLE
9 INSTALL PC SOFTWARE
MODE TITLE
WHETHER ISSUE RECEIPT OR
NOT CAN BE CHANGED BY
DEPRESSING [RCPT] KEY
IF THE INDICATOR
"_" APPEARS ON
DISPLAY, RECEIPT IS NOT
ISSUED, IN THIS CASE,
DEPRESSING [RCPT] KEY
WILL ENABLE RECEIPT
PRINT AGAIN
1.INSERT CUSTOMER
SUPPORT CD IN YOUR PC
2.INSTALLATION PROGRAM
RUNS AUTOMATICALLY
(FOR USB CONNECTION)
3.AFTER INSTALLATION
OF SOFTWARE,
-TURN OFF ECR
-CONNECT PC AND ECR VIA
USB CABLE
-TURN ON ECR
-SELECT "INSTALL THE
SOFTWARE
AUTOMATICALLY" AT
HARDWARE WIZARD
7-[HELP]: “NOT ASSIGNED” IN THE DISPLAY
HEADER
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
7 "NOT ASSIGNED"DISPLAY
MODE TITLE
[ERROR STATUS]
NO ENTRY OF CLERK CODE
[RESOLUTION]
ENTER A CLERK CODE
EX) ENTRY OF CLERK #1
1-[CLK#]
8-[HELP]: SD CARD
HEADER
05/02/2006 12:34PM
01
123456#1234
BETTY___
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./CLERK NAME
8 SD CARD COMMAND
MODE TITLE
(PGM MODE)
[SBTL]-XXX-[@]-[SBTL]
XXX=
140:FORMAT
141:SAVE PROGRAMMING
144:SAVE ALL RAM
145:LOAD GRAPHIC LOGO
147:LOAD PROGRAMMING
148:LOAD ALL RAM
(X1/Z1 MODE)
SAVE SALES DATA
650-[.]-[@]-[SBTL]
XE-A41S
PROGRAM MODE
2 – 19
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE
Roughly speaking, the following sales reports are available:
[Purpose]
1) OP X/Z reports (Individual cashier reports)
The above reports are each used to check sales data. The standard
purposes of taking these reports are as follows:
2) X1/Z1 reports (Daily total X and Z reports)
3) X2/Z2 reports (Periodic total X and Z reports)
OP X/Z reports : These reports are taken by operators in order to
report their own sales data.
4) Flash-read reports (Display sales amount)
X1/Z1 reports
: These reports are taken by the supervisor or manager in
order to check and report daily sales totals at that point.
In addition to the above reports that are to be used for program checking are also available.
X2/Z2 reports
: These reports are taken by the owner or manager in
order to check and report periodic (weekly or monthly)
totals.
Flash-read
: These reports are taken by the owner or manager in
order to check and display sales totals at that point.
[Operation]
In the table below those reports marked with a circle “{” can be executed.
PRINTING REPORT
MODE
REPORT NAME
KEY ENTRY
OPX/Z
X1/Z1
X
Z
X1
[CA/AT/NS]
−
−
{
[DEPT#]
−
−
{
DEPT IND. GROUP
NK3[@/FOR]3[DEPT#]
−
DEPT GROUP TOTAL
[0]3[@/FOR]3[DEPT#]
PLU/UPC BY RANGE
DATA FOR READING
X2/Z2
X2
Z2
{
{
−
{
−
−
{
−
{
−
−
−
{
−
{
−
[PLU/UPC]
−
−
{
{
{
{
PLU/UPC CODE
NK3
[DEPT SHIFT]3[PLU/UPC]
−
−
{
−
{
−
DEPT. CODE
TRANSACTION
[1] 3[CA/AT/NS]
−
−
O
−
{
−
TL-ID
[2] 3[CA/AT/NS]
−
−
{
−
{
−
CLERK (ALL)
[CLK#/CONV]
−
−
{
{
{
{
*1
CLERK (INDIVIDUAL)
[CLK#/CONV]
{
{
−
−
−
−
*1, *3
HOURLY (ALL)
[#/TM/SBTL]
−
−
{
{
−
−
*1
HOURLY (RANGE)
[#/TM/SBTL]
−
−
{
−
−
−
DAILY NET
[#/TM/SBTL]
−
−
−
−
{
{
GENERAL
DEPARTMENT
PLU/UPC BY DEPT
Z1
*1
GROUP NO.
TIME (HOUR)
*1, *2
*1, *5
*1
FLASH READING REPORT
MODE
REPORT NAME
DEPARTMENT
CID
SALES TOTAL
MODE:
KEY ENTRY
OPX/Z
X1/Z1
DATA FOR READING
X2/Z2
X
Z
X1
Z1
X2
Z2
[DPTn] or [DEPT SHIFT]3
[DPTn] or NK3[DEPT#]
{
−
−
−
−
−
[@/FOR]
{
−
−
−
−
−
*4
[CA/AT/NS]
{
−
−
−
−
−
*4
X : Daily operater X report
Z : Daily operater Z report
X1 : Daily X report
Z1 : Daily Z report
X2 : Periodic X report
Z2 : Periodic Z report
(X report) : The corresponding data is held in the ECR.
(Z report) : The corresponding data is cleared in the ECR.
XE-A41S
OP X/Z, X1/Z1, X2/Z2 MODE
3–1
DEPT CODE
*4
[Action]
• Stop of printing reports (Report cancel function):
This ECR has the function of report stopping for PLU/UPC report.
Individual counters for the following Z reports are incremented when
those reports are printed.
• Printing of GT on X reports:
This ECR dose not print any GT on X reports.
1) General daily total report (Z1)
2) General periodic total report (Z2)
*1 To read respective reports, it is necessary to follow the procedure
below.
[Additional function]
(1) Overflow mark
If the amount or quantity in any totalizer other than GT to be printed
on X or Z reports exceeds a programmed limit, the indication mark
(overflow mark) is printed for the totalizer concerned.
The overflow mark may be printed even if a totalizer does not reach
the maximum amount. This occurs, for example, when the amount
or quantity in the totalizer gets smaller than the maximum amount
due to the entry of a negative amount after the overflowing of the
totalizer. This means that when the totalizer overflows once, the
overflow mark (for example, “!!”) is printed.
Reading
(X report)
KEY
Resetting
(Z report)
*2 PLU/UPC code range can be specified by entering the start and
end numbers according to the following procedure.
When specifying a single PLU/UPC code, the start number has only
to be entered.
(2) MODE TITLE
Each report is printed MODE TITLE at a header of report.
The Report Titles are as follows.
All
Reading
Start No.
@/FOR
PLU/UPC
End No.
Resetting
(START No.) and (END No.) : PLU
UPC (FAN) CODE
(4digit)
(13digit)
*3 To read respective reports, it is necessary to follow the procedure
below. The clerk code does not need to enter at the OPX/Z mode.
In OPX/Z mode, it is issued the report of the assigned clerk.
*OPX*
OPZ report
*OPZ*
X1 report
*X 1*
Z1 report
*Z 1*
X2 report
*X 2*
Z2 report
*Z 2*
(3) Report cancel function
It can be cancelled by turned the mode switch to MGR position
while the data is printed. (In this case, the contents of memory are
not cleared.)
*4 Reading display only.
The displayed amount can be cleared by [CL] key.
KEY
(Display amount)
OPX report
CL
(Display initialize)
<Print sample of Report cancel>
*5 Hourly range can be specified by entering the start and end hour according to the following procedure.
When specifying a single hour, the start hour has only to be entered.
:
:
*
All
*
*
*
*
*
1 the report cancel symbol
123456789012345678901234
Reading
XX
Start
@/FOR
XX
End
Samples of respective reports are shown on the following pages.
#/TM/SBTL
Resetting
XE-A41S
OP X/Z, X1/Z1, X2/Z2 MODE
3–2
SD CARD FUNCTION
[Key Sequence of SD Jobs]
Spet 3) Create the “STATUS.REC” file in new sub-folder
when all files are saved completely.
[X1/Z1 Mode]
File Name
(*1) (*2)
xxx
@/FOR
1
SBTL
CA/AT/NS : Execute operation (*3)
CL
1 Status information
STATUS. REC
: Cancel
Step 4) Update the “SRECORD.REC” file for changing the structure of
sub-folder.
xxx:
JOB code
File Name
650: Save Sales Data (ECR 3 SD)
1 Record structure
(*1) When [SBTL]-key is pushed, ECR prints the confirmation
message at “RECEIPT” (not print at JOURNAL) and enforces to
select either executing or canceling this job. The buffered keys are
cleared.
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted to
use at “Customer Support Tool” software on PC.
(*2) “1” is a keyword to execute this job.
Note: Each files are used only for the “Customer Support Tool” software on PC. Any users dose not need to concern its contents.
(*3) If the MODE SWITCH is turned to another mode from X1Z1
position or the AC POWER is off when job is executed, the job is
cancelled.
Note: If AC POWER is off when ECR accesses SD CRAD, the contents in SD CARD may be broken.
The action of each job is as below.
[JOB#650] Sales data saving
All sales data (Daily and term) save in SD card.
This job is used for the purpose of using Electric Journal Data at the
“Customer Support Tool” software on PC. Maximum 400 times data is
kept in SD Card when the SD memory is not full.
The action is as below.
Step1) After reading the information of the current sub-folder in
“SRECORD.REC” file, ECR creates the new sub-folder under
the folder for “Sales Data”.
Its folder is named ASCII Character that is indicated the number of sales data in SD Card. (Example: “1”, “2”, “3”,......)
Step2) Save the below data in new sub-folder that is created above step.
File
Name
File/Table
No. (*1)
mtimtbl
D0
2 Department Sales
Dept
01
All fields
3 Transaction Sales
Trans
21
All fields
FuncText
A4
Hourly
61
1 Date and Time
(when a job is operated)
4 Hourly Sales
Field (*1)
All fields
5 Daily Net Sales
DailyNet
71
All fields
6 Clerk Sales
CsrData
51
All fields
7 PLU/UPC Sales
CsrSal
52
All fields
Plu
11
All fields, All range
XE-A41S
SRECORD. REC
OP X/Z, X1/Z1, X2/Z2 MODE
3–3
■ DISPLAY AND PRINT: X1/Z1 MODE)
JOB ENTRY OPERATION: (Common action for all Jobs)
Key
Display
Print
1 2 3 4 5 6 7 8 9 0 1 23 4 5 6
123456789012345678901234
650 [.] [@/FOR]
[#/TM/SBTL]
[1]
NOTE
X1Z1
650
ARE YOU EXECUTE?
0
Numeric entry
(PRE-PRINT HEADDER)
!!!!!!!!!!!!!!!!!!!!!!!!
YOU SELECT SD CARD JOB
[1]-[CA/AT]KEY : EXECUTE
[CL]-KEY :
CANCEL
!!!!!!!!!!!!!!!!!!!!!!!!
Don't turn the mode key
while executing a job.
!!!!!!!!!!!!!!!!!!!!!!!!
(Issuing Receipt)
The buffered keys are cleared and the message is
printed on "receipt" only.
MESSAGE : MAX 8-lines
(The message is fixed in ROM.)
(Not count up CC# at this time.)
ARE YOU EXECUTR?
1
[CA/AT/NS]
PRINT
(HEADER)
05/02/2006 12:34PM
123456#1234
01
: (Count up CC#.)
JOB HEADDER is printed.
And job code is printed.
(Job code is printed only at SD jobs)
BETTY___
*Z1*
#650
(SD ACCESS)
ACCESSING CARD
PRINT : (NON)
DISPLAY : ■ :Blinking
■
Case of NORMAL END
X1Z1 SD FINAL
0. 00
PRINT
(Issuing Receipt)
Case of ERROR END
(NO CARD)
NO CARD
X1Z1 NO CARD
0. 00
(Issuing Receipt)
Case of ERROR END
(ACCESS ERROR)
ACCESS ERROR
(Issuing Receipt)
Case of CHANGING MODE KEY
(to cancel)
SD CANCEL
: STATUS is printed
(The message is fixed in ROM.)
DISPLAY : Initial Display
ERROR MESSAGE
(Refer to list of “ERROR MESSAGE”)
(The message is fixed in ROM.)
ERROR MESSAGE
(Refer to list of “ERROR MESSAGE”)
(The message is fixed in ROM.)
PRINT
: SD CANCEL MESSAGE
(The message is fixed in ROM.)
PRINT
: MESSAGE of POWER OFF
(The message is fixed in ROM.)
(Issuing Receipt)
Case of POWER OFF
POWER OFF
X1Z1
POWER OFF ERROR
0. 00 AT THE DEVICE CONTROL
SET DATA&TIME AGAIN
(Issuing Receipt)
The messages are printed on both RECIPT and JOURNAL.
[ERROR CODE LIST]
No.
Description
MESSAGE (12Characters) DISPLAY
PRINT
01
SD card is not find
NO CARD
{
{
02
SD CARD PROTECT SWITCH is set “PROTECED”
CARD PROTECT
{
{
03
SD CARD WRITTING ERROR (Memory is full) (ECR cannot write the data on SD card.)
CARD FULL
{
{
04
SD CARD ACCESS ERROR (File is nothing)
ACCESS ERROR
{
{
SD CARD ACCESS ERROR (File data is failed) (ECR cannot read the data on SD card.)
FILE FAILED
{
{
OVER LIMIT.
{
{
05
:
10
:
<<< Reserved >>>
Over limitation of data records (Over max record in sales or EJ data.)
<<< Reserved >>>
99
SD CARD ERROR
(Anyhow error except above SD ERROR is occurred when ECR accesses SD Card.)
SD ERROR
{
{
xx
Power off is occurred at SD card job
POWER OFF
{
−
xx
Operation is canceled
SD CANCEL
{
{
Note: Column of DISPLAY/PRINT : “{” : Used, “−” : Not used.
XE-A41S
OP X/Z, X1/Z1, X2/Z2 MODE
3–4
COPYRIGHT  2006 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Information and Communication Systems Group
Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2006 October Printed in Japan t