S

P E C

F

I L E

P r o d u c t N u m b e r :

PT-VW431D

P r o d u c t N a m e :

LCD Projector

As of September 2012. Specifications and appearance are subject to change without notice.

SFL12M015

1 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Specifications

Main unit

Power supply

Power consumption

LCD panel

Lens

Throw ratio

Lamp

Screen size

Colors

Brightness*

Contrast* 2

Resolution

2

Panel size

Display method

Pixels

Pixel configuration

Center-to-corner uniformity*

Scanning frequency

2

HDMI

RGB

YP

B

P

R

(YC

Video/S-Video

Optical axis shift

Keystone correction range

Installation

Built-in speaker Size

Output power

Terminals

DIGITAL LINK

HDMI IN

COMPUTER (RGB) 1 IN

R, G, B

Y, P

B

B

(C

C

B

R

)

), P

R

(C

R

)

100 –240 V AC, 50/60 Hz

365 W

(0.3 W when

STANDBY MODE set to

ECO

,* 1 12.5 W when

STANDBY MODE set to

NETWORK

(19.7 W with DIGITAL LINK, 27.5 W, when

STANDBY MODE of

SOUND is set to

ON

.))

15.0 mm (0.59 inches) diagonal (16:10 aspect ratio)

Transparent LCD panel (× 3, R/G/B)

1,024,000 (1,280 × 800) × 3, total of 3,072,000 pixels

Stripe

Manual zoom (1.6×), manual focus,

F 1.60 – 2.12, f 15.28 – 24.62 mm

1.18 –1.90:1

280 W UHM lamp

0.76–7.62 m (30 – 300 inches) diagonally, 16:10 aspect ratio

Full color (16,777,216 colors)

4,300 lumens (

LAMP POWER

:

NORMAL

)

85%

3,500:1 (full on/off,

LAMP POWER

:

NORMAL

, with iris on)

1,280 × 800 pixels (Input signals that exceed this resolution will be converted to 1,280 × 800 pixels.) f

H

: 25 – 80 kHz, f

V

: 24 – 85 Hz, dot clock: 162 MHz or lower f

H

: 15 – 100 kHz, f

V

: 50 – 100 Hz, dot clock: 140 MHz or lower

(Signals exceeding the dot clock rate of 140 MHz are downsampled.)

480i (525i):

576i (625i): f f

H

H

15.75 kHz; f

15.63 kHz; f

V

V

60 Hz,

50 Hz,

480p (525p):

576p (625p): f

H

31.50 kHz; f

V

60 Hz, f

H

31.25 kHz; f

V

50 Hz,

720 (750)/60p: f

H

45.00 kHz; f

V

60 Hz,

720 (750)/50p: f

H

37.50 kHz; f

V

50 Hz,

1080 (1125)/60i: f

H

33.75 kHz; f

V

60 Hz,

1080 (1125)/50i: f

H

28.13 kHz; f

V

50 Hz f

H

: 15.75 kHz, f

V

: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60] f

H

: 15.63 kHz, f

V

: 50 Hz [PAL/PAL-N/SECAM] f

H

: 25 – 80 kHz, f

V

: 50 – 85 Hz, dot clock: 162 MHz or lower

Vertical: +48% (manual)

Vertical: ±30° (±20° with Real-Time Keystone Correction)

Ceiling/desk, front/rear (menu selection)

4 cm (1-9/16 inches) (round) × 1

10 W (monaural)

HDMI 19-pin × 1, Deep Color, HDCP compatible

480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p,

1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p,

1080 (1125)/50p

VGA (640 × 480) – WUXGA* audio signal: linear PCM

3 (1,920 × 1,200),

(sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)

D-sub HD 15-pin (female) × 1

G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;

B, R: 0.7 Vp-p, 75 ohms;

HD/VD, SYNC: high impedance, TTL (positive/negative)

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal);

P

B

(C

B

), P

R

(C

R

): 0.7 Vp-p, 75 ohms

As of September 2012

SFL12M015

2 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Power cord length

Cabinet materials

Dimensions (W × H × D)

Weight

Operation noise

Operating temperature

Operating humidity

COMPUTER (RGB) 2 IN / 1 OUT

R, G, B D-sub HD 15-pin (female) × 1

(input/output selectable using on-screen menu.)

G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;

B, R: 0.7 Vp-p, 75 ohms;

HD/VD, SYNC: high impedance, TTL (positive/negative)

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

VIDEO IN

S-VIDEO IN

COMPUTER AUDIO IN 1

RCA pin × 1, 1.0 Vp-p, 75 ohms

Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms

M3 (L, R) × 1, 0.5 Vrms

COMPUTER AUDIO IN 2 / MIC IN

M3 (L, R) × 1, 0.5 Vrms

VIDEO/S-VIDEO AUDIO IN

RCA × 2 (L/R × 1), 0.5 Vrms

AUDIO OUT

SERIAL IN

LAN/DIGITAL LINK

M3 (L, R) × 1 (monitor out: 0 – 2.0 Vrms, variable)

D-sub 9-pin (female) × 1, for external control (RS-232C compliant)

RJ-45 × 1, for network connection/DIGITAL LINK, 100Base-TX/10Base-

T, compliant with PJLink™

2.0 m (6 ft 7 in)

Molded plastic

379 × 107 * 4 × 305* 5

(14-29/32 × 4-7/32 * 4 mm

× 12* 5 inches)

Approximately 4.8 kg (10.6 lbs)

37 dB (

LAMP POWER

:

NORMAL

), 29 dB (

LAMP POWER

:

ECO

)

0 – 40 °C (32 – 104 °F)

20%– 80% (no condensation)

Remote control unit

Power supply

Operation range* 6

Dimensions (W × H × D)

Weight

Supplied accessories

3 V DC (R03/LR03/AAA type battery × 2)

Approximately 7 m (23 ft) when operated from directly in front of the signal receptor

52 × 110 × 18 mm (2-1/16 × 4-11/32 × 23/32 inches)

Approx. 67 g (2.4 oz) (including batteries)

Power cord (× 1) (× 2 for PT-VW431DEA)

AC power cord holder (× 1)

Wireless remote control unit (× 1)

Batteries for remote control (R03/LR03/AAA type × 2)

Carrying bag (× 1)

Computer cable (1.8 m (5 ft 11 in), for VGA) (× 1)

Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring and Control Software) (× 1)

Optional accessories

Replacement lamp unit

Replacement filter unit

Ceiling mount bracket

Bracket assembly

Digital interface box

ET-LAV200

ET-RFV200

ET-PKV100H (for high ceilings)

ET-PKV100S (for low ceilings)

ET-PKV200B

ET-YFB100

Weights and dimensions shown are approximate. Specifications subject to change without notice.

*1

When the

STANDBY MODE is set to

ECO

, network functions such as power on over the LAN network will not operate. Also, only certain commands can be received for external control using the serial terminal.

*2

*3

Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

*4

*5

With legs at shortest position.

Protruding parts not included.

*6

Operation range differs depending on environments.

As of September 2012

SFL12M015

3 / 1 3

S

P E C

LCD Projector

F

I L E

Dimensions

PT-VW431D

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

9 0. 5

( 3 - 9 /16 )

379 (14 -29 / 32 )

18 9. 5

( 7-15 / 32 )

Terminals

1 2 3 4

5 6 7 8 9 10 11

1 Computer 1 input

2 Computer 2 input / computer 1 output

3 HDMI input

4 LAN / DIGITAL LINK connector

5 Serial input

6 Video input

7 Audio input for video/S-Video

8 Audio input for computer 1

9 Audio input for computer 2 / mic input

10 Audio output

11 S-Video input

As of September 2012

SFL12M015

4 / 1 3

S

P E C

LCD Projector

F

I L E

Standard setting-up position

∅

38

(1-1/2)

PT-VW431D

NOTE:

Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and bracket assembly ET-PKV200B.

This illustration is not drawn to scale.

Upper edge of projected image

L

Projected image

L

Lower edge of projected image

143

(5-5/8)

162

(6-3/8)

unit : mm (inch)

L

Projected image

100

(3-15/16)

100

(3-15/16)

200

(7-7/8)

C a u t i o n :

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket. To prevent the projector from dropping, attach the wire that is included with the projector between the mounting bracket and the ceiling.

Projection distance for 16:10 aspect ratio screen

unit: meters (feet)

Projection size

[diagonal]

0.76 m

1.02 m

1.27 m

1.52 m

1.78 m

2.03 m

2.29 m

2.54 m

3.05 m

3.81 m

5.08 m

6.35 m

/

/

/

/ 120˝

150˝

200˝

250˝

7.62 m / 300˝

/

/

/

/

/

/ 70˝

80˝

/ 90˝

/ 100˝

30˝

40˝

50˝

60˝

Projection distance [L]

Min [wide]

1.8

2.0

2.3

2.5

0.7

1.0

1.3

1.5

3.1

3.8

5.1

6.4

7.7

(10.2)

(12.5)

(16.7)

(21.0)

(25.3)

(2.3)

(3.3)

(4.3)

(4.9)

(5.9)

(6.6)

(7.5)

(8.2)

Max [telephoto]

2.9

3.3

3.7

4.1

1.2

1.6

2.0

2.5

4.9

6.2

8.3

10.3

12.4

(3.9)

(5.2)

(6.6)

(8.2)

(9.5)

(10.8)

(12.1)

(13.5)

(16.1)

(20.3)

(27.1)

(33.9)

(40.6)

Height from the edge of screen to center of lens [ H ]

0.01

− 0.20

0.01

− 0.27

0.01

− 0.34

0.02

− 0.40

0.02

− 0.47

0.02

− 0.54

0.02

− 0.61

0.03

− 0.67

0.03

− 0.81

0.04

− 1.01

0.05

− 1.35

0.07

− 1.68

0.08

− 2.02

NOTE:

• The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.

(0.03

−

(0.03

−

(0.03

−

(0.07

−

(0.07

−

(0.07

−

(0.07

−

(0.10

−

(0.10

(0.13

(0.16

(0.23

(0.26

−

−

−

−

−

0.66)

0.89)

1.12)

1.31)

1.54)

1.77)

2.00)

2.20)

2.66)

3.31)

4.43)

5.51)

6.63)

As of September 2012

SFL12M015

5 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Projection distance for 16:9 aspect ratio screen

unit: meters (feet)

Projection size

[diagonal]

0.76 m

1.02 m

1.27 m

1.52 m

1.78 m

2.03 m

2.29 m

2.54 m

3.05 m

3.81 m

5.08 m

6.35 m

/

/

/

/

/

/

/

/

/

/

30˝

40˝

50˝

60˝

70˝

80˝

/ 90˝

/ 100˝

120˝

150˝

200˝

250˝

7.62 m / 300˝

Min [wide]

1.8

2.1

2.3

2.6

0.8

1.0

1.3

1.6

3.1

3.9

5.3

6.6

7.9

Projection distance [L]

(2.5)

(3.4)

(4.2)

(5.1)

(6.0)

(6.8)

(7.7)

(8.6)

(10.3)

(12.9)

(17.2)

(21.5)

(25.9)

Max [telephoto]

1.2

1.7

2.1

2.5

3.0

3.4

3.8

4.2

5.1

6.4

8.5

10.6

12.7

(3.9)

(5.6)

(6.9)

(8.2)

(9.8)

(11.2)

(12.5)

(13.8)

(16.7)

(21.0)

(27.8)

(34.8)

(41.7)

Height from the edge of screen to center of lens [ H ]

0.01

− 0.19

0.01

− 0.25

0.01

− 0.31

0.02

− 0.37

0.02

− 0.44

0.02

− 0.50

0.02

− 0.56

0.03

− 0.62

0.03

− 0.75

0.04

− 0.93

0.05

− 1.25

0.06

− 1.56

0.08

− 1.87

NOTE:

• The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.

(0.03

−

(0.03

−

(0.03

−

(0.07

−

(0.07

−

(0.07

−

(0.07

−

(0.10

−

(0.10

(0.13

(0.16

(0.20

(0.26

−

−

−

−

−

0.62)

0.82)

1.02)

1.21)

1.44)

1.64)

1.84)

2.03)

2.46)

3.05)

4.10)

5.12)

6.14)

Calculation of the projection distance

For a screen size different from the above, use the equation below to calculate the projection distance.

Aspect ratio 16:10 minimum L (m) = (diagonal screen size in inches) × 0.0257 – 0.0294

maximum L (m) = (diagonal screen size in inches) × 0.0414 – 0.0319

Aspect ratio 16:9 minimum L (m) = (diagonal screen size in inches) × 0.0264 – 0.0294

maximum L (m) = (diagonal screen size in inches) × 0.0426 – 0.0319

NOTE:

Distances calculated with the above equations will include a slight error.

As of September 2012

SFL12M015

6 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Shift range

Optical axis shift function allows to shift the position of a projected image as shown below.

• Floor mount • Ceiling mount

H

(Width of projected image)

H

(Width of projected image)

Standard postition of projected image

Standard postition of projected image

Installable angle

Install the projector at an angle within the range shown below.

• Vertical direction

The projector may be installed at a vertical angle of 30°.

• Horizontal direction

The projector may be installed at a horizontal angle of 15°.

+30°

+15°

-15°

-30°

As of September 2012

SFL12M015

7 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

List of compatible signals

The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 25 kHz to 80 kHz (15 kHz to 100 kHz for RGB signals), vertical scanning frequencies of

50 Hz to 120 Hz (50 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum (140 MHz maximum for RGB signals) can be input.

NOTE: The native resolution of this projector is 1,280 × 800 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.

Format Display mode

NTSC/NTSC4.43/PAL-M/PAL60

PAL/PAL-N/SECAM

480i (525i)

576i (625i)

480p (525p)

576p (625p)

720p

1035i

1080i

Display resolution

(dots)*

1

720 × 480i

720 × 576i

640 × 480i

768 × 576i

640 × 480

768 × 576

1280 × 720

1080/24p

VGA

1920 × 1035i

1920 × 1080i

1920 × 1080

640 × 400

640 × 480

MAC LC13

MAC13

SVGA

MAC16

XGA

720 × 400

640 × 480

800 × 600

832 × 624

1024 × 768

1024 × 768i

48.5

58.0

60.0

60.3

61.0

62.0

63.5

56.5

68.7

36.0

35.5

60.2

MAC19

1024 × 768

*1 The “i” appearing after the resolution indicates an interlaced signal.

32.7

34.5

35.2

37.9

37.9

38.0

38.6

46.9

37.5

37.9

37.9

43.3

31.5

35.0

35.0

48.1

53.7

49.7

44.0

46.9

47.0

48.4

Scanning frequency

H V

(kHz) (kHz)

15.7

15.6

15.7

15.6

31.5

31.3

45.0

37.5

33.8

33.8

28.1

27.0

31.5

31.5

59.9

50.0

59.9

50.0

59.9

50.0

60.0

50.0

60.0

60.0

50.0

24.0

70.1

59.9

51.1

55.4

56.3

60.3

61.0

60.5

60.3

75.0

72.2

85.1

74.6

54.6

58.2

58.3

60.0

75.0

72.8

74.4

85.0

70.1

66.6

66.7

60.0

72.0

75.0

74.9

75.7

77.1

79.4

70.1

85.0

87.2

87.0

75.1

65.2

74.7

78.8

79.3

81.0

84.3

83.4

75.0

94.5

47.3

44.9

80.0

40.0

40.0

40.1

38.6

49.5

50.0

56.3

57.3

31.5

31.5

31.5

36.0

28.3

31.3

30.2

32.7

36.4

36.0

59.1

63.0

61.7

65.0

29.5

74.3

74.3

74.3

74.3

74.3

74.3

25.2

25.2

Dot clock frequency

(MHz)

−

−

12.3

14.8

25.2

VIDEO/S-VIDEO

YP

B

P

R

/RGB

DIGITAL LINK/

HDMI/YP

B

P

R

/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

As of September 2012

SFL12M015

8 / 1 3

S

P E C

LCD Projector

F

I L E

Display mode

WXGA

Display resolution

(dots)*

1

1280 × 768

1280 × 800

MAC21

SXGA

MAC

SXGA+

WXGA+

UXGA

WSXGA+

WUXGA

1360 × 768

1366 × 768

1376 × 768

1152 × 870

1152 × 900

1280 × 960

1280 × 1024

1280 × 1024i

1280 × 960

1280 × 1024

1400 × 1050

1440 × 900

1600 × 1200

1680 × 1050

1920 × 1200

50.0

46.4

75.0

80.0

64.0

65.4

65.1

55.9

81.1

64.0

80.0

63.4

77.0

63.8

91.1

50.0

74.9

75.0

81.3

87.5

93.8

65.3

74.0

74.6

71.4

61.9

60.0

62.5

63.3

63.7

63.9

71.7

71.5

47.7

56.2

48.4

48.4

68.7

61.2

*1 The “i” appearing after the resolution indicates an interlaced signal.

NOTE: DIGITAL LINK and HDMI inputs share the same compatible signal.

47.8

60.3

68.6

41.2

49.6

49.7

56.0

57.6

58.2

60.0

62.8

63.9

Scanning frequency

H V

(kHz) (kHz)

59.9

74.9

84.8

50.0

60.1

59.8

70.0

72.0

70.0

72.0

74.9

60.0

75.1

60.2

60.1

59.9

59.9

60.0

60.0

65.0

60.0

72.0

60.2

85.0

86.0

94.0

86.7

75.1

70.0

75.0

60.0

59.9

59.9

58.6

60.0

60.0

60.0

67.2

76.1

60.2

75.0

84.8

60.0

72.0

60.0

60.0

75.1

65.2

75.6

66.0

60.0

PT-VW431D

Dot clock frequency

(MHz)

79.5

102.3

117.5

68.6

79.4

83.5

95.0

97.8

98.9

102.8

106.5

108.0

80.0

78.4

126.0

135.2

108.0

122.9

122.4

106.5

161.9

162.0

175.5

189.0

202.5

146.3

154.0

193.3

108.0

107.3

109.5

108.0

117.0

135.0

108.1

135.0

122.5

86.7

86.7

100.1

86.7

100.0

92.0

105.1

94.5

108.0

111.5

130.1

109.5

157.5

80.0

Format

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

DIGITAL LINK/

HDMI/RGB

RGB

As of September 2012

SFL12M015

9 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Serial connector

The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.

Pin assignments and signal names

1

6 9

5

D-sub 9-pin (female)

Serial input

3

4

5

No.

1

2

Signal name

–

TXD

RXD

–

GND

Description

NC

Send data

Receive data

NC

Ground

8

9

No.

6

7

Signal name

–

CTS

RTS

–

Description

NC

Connected internally

Connected internally

NC

Communication conditions (factory setting)

Signal level

Synchronization method

Baud rate

Parity

RS-232C-compliant

Start-stop synchronization

9,600 bps

None

Character length

Stop bit

X parameter

S parameter

8 bits

1 bit

None

None

Basic format

Transmission from the computer begins with STX, then command, parameter, and ETX are sent in this order. Add parameters according to the details of control.

STX C1 C2 C3 : P1 P2 ... Pn ETX

Start

(1 byte) Command

(3 bytes)

Colon

(1 byte) Parameters

End

(1 byte)

(undefined length)

NOTE: When sending commands without parameters, a colon (:) is not necessary.

Basic format with sub-commands

Same as the basic format without sub-commands

STX C1 C2 C3 : ETX

S1 S2 S3 S4 S5 E P1 P2 P3 P4 P5 P6

Sub-command

(5 bytes)

Parameters (6 bytes):

“+” or “-” sign (1 byte) with setting/adjusting value (5 bytes)

Operation (1 byte):

“=” (Sets the value designated by the parameters)

NOTE: When sending sub-commands that require no parameters, operation (E) and parameters are not necessary.

CAUTION

• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again.

• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.

• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10 seconds or more.

As of September 2012

SFL12M015

1 0 / 1 3

S

P E C

LCD Projector

F

I L E

Cable specifications

Projector

1

2

5

6

3

4

7

8

9

NC

NC

NC

NC

NC

NC

NC

NC

PC (DTE)

1

2

5

6

7

3

4

8

9

PT-VW431D

Control commands

Command: <Parameter> Function Callback: <Parameter> Parameter value

Min Max

P O N

P O F

A V L : < p l >

I I S : < i n p u t s i g n a l >

O F Z : < o f f o n >

V P M : S T D

V P M : D Y N

V P M : C I N

V P M : R E A

V P M : B B D

V P M : C B D

V P M : I M 1

V P M : I M 2

V P M : I M 3

V P M : I M 4

A U U

A U D

O S H

D Z U

D Z D

*

*

*

1/

1

1

* 2

Power on (standby mode on)

Power off (standby mode off)

Volume control

Input signal selection

Freeze

Picture mode: Standard

Picture mode: Dynamic

Picture mode: Cinema

Picture mode: Real

Picture mode: Blackboard

Picture mode: Colorboard

Picture mode: Image 1

Picture mode: Image 2

Picture mode: Image 3

Picture mode: Image 4

Volume up

Volume down

AV mute

Digital zoom: Enlargement

Digital zoom: Reduction

P O N

P O F

A V L : < p l >

I I S : < i n p u t s i g n a l >

O F Z : < o f f o n >

V P M : S T D

V P M : D Y N

V P M : C I N

V P M : R E A

V P M : B B D

V P M : C B D

V P M : I M 1

V P M : I M 2

V P M : I M 3

V P M : I M 4

A U U

A U D

O S H

D Z U

D Z D

*1 Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.

*2 These commands are effective when the standby mode is set to eco. (Other commands are not effective.)

–

–

–

–

–

–

–

1

–

–

–

63

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

0

–

–

–

0

–

–

–

–

–

–

–

–

As of September 2012

SFL12M015

1 1 / 1 3

S

P E C

LCD Projector

F

I L E

Status request commands

PT-VW431D

Command

Q P W

Q $ S

Q I N

Q A V

Q P M

Q F Z

Q $ L

Q S H

*

*

Description

Standby power status

Lamp status

Input signal status

Volume adjustment value

Picture mode status

Freeze status

Lamp run time

AV mute function status

Standard

Dynamic

Cinema

Real

Blackboard

Colorboard

Image 1

Image 2

Image 3

Image 4

B B D

C B D

I M 1

I M 2

I M 3

I M 4

Callback

<Parameter>

< p o w e r c o n d i t i o n >

< l a m p c o n d i t i o n >

< i n p u t s i g n a l >

< p l >

S T D

D Y N

C I N

R E A

< o f f _ o n >

< a c c t c h >

< o f f _ o n >

*

These commands are effective when the standby mode is set to eco. (Other commands are not effective.)

Parameter format

Parameter format

<pl>

<off on>

<input signal>

<power condition>

<lamp condition>

<acctch>

3

1

4

Size (Byte)

1

3

3 (1 or 2 bytes also possible when under control)

7

Definition

Decimal without signs: 0 to 999 (000, 001, 002...999)

Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)

Callback from the projector is 3 Byte.

0 = off, 1 = on

DL1 = DIGITAL LINK, HD1 = HDMI, RG1 = computer 1 (RGB),

RG2 = computer 2 (RGB), VID = video, SVD = S-Video,

SCT=Computer 1 (Scart)

When Digital interface box is connected to DIGITAL LINK terminal, and

INPUT is selected to DIGITAL LINK terminal and Digital interface box at the same time:

DL1: HD1 = HDMI 1

DL1: HD2 = HDMI 2

DL1: PC1 = Computer 1 (RGB)

DL1: PC2 = Computer 2 (RGB)

DL1: VID = Video

DL1: SVD = S-Video

000 = power off (standby mode off), 001 = power on (standby mode on)

0 = standby, 1 = lamp on under control, 2 = lamp on,

3 = lamp off under control

Decimal without signs: 0000 – 9999 hours

Command example

To set the volume to +30, send the command as shown below.

STX AVL : 30 ETX

Start Command Parameter End

NOTE: When sending commands without parameters, a colon (:) is not necessary.

As of September 2012

SFL12M015

1 2 / 1 3

S

P E C

LCD Projector

F

I L E

PT-VW431D

Notes on projector placement and operation

The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

1.

Never place objects on top of the projector while it is operating.

2.

Make sure there is the unobstructed space as shown below or more around the projector’s exhaust openings. In addition to this space, also ensure that there is a sufficient work space for removing and installing the lamp, filter and other parts.

3.

Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector so that cool or hot air from other air conditioning equipment does not flow directly toward the projector’s air intake or exhaust openings.

4.

Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the intake opening. This may cause the projector’s protective circuit to interrupt projector operation.

500 mm (1 ft 8 in) or more

500 mm (1 ft 8 in) or more

1,000 mm ( 3 ft 3 in) or more

Direction of air intake and exhaust

Intake

Exhaust

Operating the projector continuously

1. If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration becomes shorter.

2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less).

Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.

Product availability differs depending on region and country. This product may be subject to export control regulations.

PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.

All other trademarks are the property of their respective trademark owners.

As of September 2012

SFL12M015

1 3 / 1 3