Denon DN-A7100 - AV Surround Preamplifier User guide

AV SURROUND PREAMPLIFIER
DN-A7100
USER GUIDE
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
GUIDA DELL’UTENTE
GUÍA DEL USUARIO
GEBRUIKSAANWIJZING
GUIA DO UTILIZADOR
BRUKSANVISNING
ENGLISH
WARRANTY
For warranty information, contact your local DENON
distributor.
RETAIN YOUR PURCHASE RECEIPT
Your purchase receipt is your permanent record of a
valuable purchase. It should be kept in a safe place
to be referred to as necessary for insurance purposes
or when corresponding with DENON.
IMPORTANT
When seeking warranty service, it is the responsibility of
the consumer to establish proof and date of purchase.
Your purchase receipt or invoice is adequate for such
proof.
FOR U.K. ONLY
This undertaking is in addition to a consumer's
statutory rights and does not affect those rights in
any way.
DEUTSCH
GARANTIE
Bei Garantiefragen wenden Sie sich bitte an Ihren
DENON-Händler.
HEBEN SIE IHRE QUITTING GUT AUF
Die Quittung dient Ihnen als bleibende Unterlage
für Ihren wertvollen Einkauf Das Aufbewahren der
Quittung ist wichtig, da die darin enthaltenen Angaben
für Versicherungswecke oder bei Korrespondenz mit
DENON angeführt werden müssen.
WICHTIG!
Bei Garantiefragen muß der Kunde eine Kaufunterlage
mit Kaufdatum vorlegen. Ihren Quittung oder
Rechnung ist als Unterlage ausreichend.
FRANÇAIS
GARANTIE
Pour des informations sur la garantie, contacter le
distributeur local DENON.
CONSERVER L'ATTESTATION D'ACHAT
L'attestation d'achat est la preuve permanente
d'un achat de valeur. La conserver en lieu sur pour
s'y reporter aux fins d'obtention d'une couverture
d'assurance ou dans le cadre de correspondances
avec DENON.
IMPORTANT
Pour l'obtention d'un service couvert par la garantie,
il incombe au client d'établir la preuve de l'achat
et d'en corroborer la date. Le reçu ou la facture
constituent des preuves suffisantes.
ITALIANO
GARANZIA
L’apparecchio è coperto da una garanzia di buon
funzionamento della durata di un anno, o del periodo
previsto dalla legge, a partire dalla data di acquisto
comprovata da un documento attestante il nominativo
del Rivenditore e la data di vendita. La garanzia sarà
prestata con la sostituzione o la riparazione gratuita
delle parti difettose.
Non sono coperti da garanzia difetti derivanti da
uso improprio, errata installazione, manutenzione
effettuata da personale non autorizzato o, comunque,
da circostanze che non possano riferirsi a difetti di
funzionamento dell’apparecchio. Sono inoltre esclusi
dalla garanzia gli interventi inerenti l’installazione e
l’allacciamento agli impianti di alimentazione.
Gli apparecchi verranno riparati presso i nostri Centri
di Assistenza Autorizzati. Le spese ed i rischi di
trasporto sono a carico del cliente.
La casa costruttrice declina ogni responsabilità per
danni diretti o indiretti provocati dalla inosservanza
delle prescrizioni di installazione, uso e manutenzione
dettagliate nel presente manuale o per guasti dovuti ad
uso continuato a fini professionali.
ESPAÑOL
GARANTIA
Para obtener información acerca de la garantia
póngase en contacto con su distribuidor DENON.
GUARDE SU RECIBO DE COMPRA
Su recibo de compra es su prueba permanente de
haber adquirido un aparato de valor, Este recibo
deberá guardarlo en un lugar seguro y utilizarlo
como referencia cuando tenga que hacer uso del
seguro o se ponga en contacto con DENON.
IMPORTANTE
Cuando solicite el servicio otorgado por la garantia
el usuario tiene la responsabilidad de demonstrar
cuándo efectuó la compra. En este caso, su recibo
de compra será la prueba apropiada.
NEDERLANDS
GARANTIE
Voor inlichtingen omtrent garantie dient u zich tot uw
plaatselijke DENON.
UW KWITANTIE, KASSABON E.D. BEWAREN
Uw kwitantie, kassabon e.d. vormen uw bewijs van
aankoop van een waardevol artikel en dienen op een
veilige plaats bewaard te worden voor evt, verwijzing
bijv, in verbend met verzekering of bij correspondentie
met DENON.
BELANGRIJK
Bij een evt, beroep op de garantie is het de
verantwoordelijkheid van de consument een
gedateerd bewijs van aankoop te tonen. Uw
kassabon of factuurzijn voldoende bewijs.
PORTUGUÊS
GARANTIA
Para informações sobre a garantia, contactar o
distribuidor DENON local.
GUARDAR O RECIBO DE COMPRA
O recibo é o registo permanente da compra que
fez. Deve ser guardado num local seguro, para
ser apresentado em questões relacionadas com
o seguro ou para quando tiver de contactar a
DENON.
IMPORTANTE
Quando procurar assisténcia técnica ao abrigo da
garantia, é da responsabilidade do consumidor
estabelecer a prova e data de compra. O recibe é
prova adequada.
SVENSKA
GARANTI
För information om garantin, kontakta DENON
lokalagent.
SPAR KVITTOT
Kvittot är ett inköpsbevis på en värdefull vara. Det skall
förvaras säkert och hänvisas till vid försäkringsfall
eller vidkorrespondens mod DENON.
VIKTIGT
Fö att garantin skall gälla är det kundens sak att
framställa bevis och datum om köpet. Kvitto eller
faktura är tillräokligt bevis fö detta.
CE MARKING
English
The DN-A7100 is in conformity with the EMC directive and low-voltage directive.
Deutsch
Das Modell DN-A7100 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte.
English
-
Français
Le DN-A7100 est conforme à la directive EMC et à la directive sur les basses tensions.
Italiano
-
Il DN-A7100 è conforme alle direttive CEE ed a quelle per i bassi voltaggi.
Español
El DN-A7100 está de acuerdo con las normas EMC y las relacionadas con baja tensión.
Nederlands
De DN-A7100 voldoet aan de EMC eisen en de vereisten voor laag-voltage.
-
Português
O DN-A7100 conforma com as diretrizes EMC e de baixa voltagem.
Svenska
DN-A7100 är tillverkad i enlighet med EMC direktiven och direktiven för lågvoltsutrusning.
-
WARNINGS
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not insert anything into the equipment through
the ventilation holes.
Do not handle the mains cord with wet hands.
Do not cover the ventilation with any items such as
tablecloths, newspapers, curtains, etc.
No naked flame sources, such as lighted candles,
should be placed on the equipment.
When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
Make a space of about 0.2 meter around the unit.
No objects filled with liquids, such as vases, shall
be placed on the equipment.
When the switch is in the OFF position, the
equipment is not completely switched off from
MAINS.
The equipment shall be installed near the
power supply so that the power supply is easily
accessible.
- Do Not Touch Hot Spots During and Immediately
After Use.
- During and immediately after use, this product is
hot in areas other than the controls and rear panel
connection jacks. Do not touch hot spots and
especially the top panel. Contact with hot areas
can cause burns.
Deutsch
WARNHINWEISE
- Das Gerät nicht Regen oder Feuchtigkeit
aussetzen.
- Die Abdeckung nicht vom Gerät abnehmen.
- Keine Gegenstände durch die Belüftungsschlitze
stecken.
- Das Netzkabel nicht mit feuchten oder nassen
Händen anfassen.
- Decken Sie die Lüftungsöffnungen nicht mit einem
Tischtuch, einer Zeitung, einem Vorhang usw. ab.
- Es dürfen keine Gegenstände mit offener Flamme,
wie etwa brennende Kerzen, auf dem Gerät
aufgestellt werden.
- Beachten Sie bei der Entsorgung der verbrauchten
Batterien alle geltenden lokalen und überregionalen
Regelungen.
- Auf allen Geräteseiten muß ein Zwischenraum
von ungefähr 0,2 meter vorhanden sein.
- Auf das Gerät dürfen keine mit Flüssigkeiten
gefüllte Behälter, wie etwa eine Vase, gestellt
werden.
- Wenn der Schalter ausgeschaltet ist (OFFPosition), ist das Gerät nicht vollständig vom
Stromnetz (MAINS) abgetrennt.
- Das Gerät sollte in der Nähe einer Netzsteckdose
aufgestellt werden, damit es leicht an das
Stromnetz angeschlossen werden kann.
- Berühren Sie während oder unmittelbar nach dem
Gebrauch keine heißen Stellen des Gerätes.
- Während oder unmittelbar nach dem Gebrauch ist
dieses Produkt mit Ausnahme der Bedienelemente
und der Anschlussbuchsen auf der Rückseite heiß.
Berühren Sie die heißen Stellen und insbesondere
die Oberseite nicht. Der Kontakt mit heißen
Flächen kann zu Verbrennungen führen.
Français
AVERTISSEMENTS
- Ne pas exposer l’appareil à la pluie ni à l’humidité.
- Ne pas essayer de retirer le boîtier de l’appareil.
- Ne rien insérer dans l’appareil par les orifices de
ventilation.
- Ne pas manipuler le cordon d’alimentation avec
les mains mouillées.
- Ne pas recouvrir les ouïes de ventilation avec un
objet quelconque comme une nappe, un journal,
un rideau, etc.
- Ne placer aucune source de flamme nue, comme
une bougie allumée, sur l'appareil.
- Pour mettre au rebut les piles usées, respecter les
lois gouvernementales ou les règlements officiels
concernant l’environnement qui s'appliquent à
votre pays ou région.
- Veiller à ce qu’aucun objet ne soit à moins de 0,2
mètre des côtés de l'appareil.
- Aucun objet rempli de liquide, un vase par exemple,
ne doit être placé sur l'appareil.
- Lorsque l'interrupteur est sur la position OFF,
l'appareil n'est pas complètement déconnecté du
SECTEUR (MAINS).
- L'appareil sera installé près de la source
d'alimentation, de sorte que cette dernière soit
facilement accessible.
- Ne pas toucher aux zones chaudes pendant et
immédiatement après l’utilisation.
- Pendant l’utilisation et immediatement apres, cet
appareil est chaud en dehors des commandes
et des prises de raccordement arriere. Ne pas
toucher aux zones chaudes, et particulièrement
au panneau supérieur, pour éviter tout risque de
brûlure.
Italiano
-
-
-
AVVERTENZE
Non esporre l’apparecchio alla pioggia o
all’umidità.
Non rimuovere il coperchio dell’apparecchio.
Non introdurre oggetti all’interno dell’apparecchio
attraverso i fori di ventilazione.
Non toccare il cavo di alimentazione con le mani
bagnate.
Non coprire le fessure di ventilazione con tovaglie,
giornali, tende od oggetti analoghi.
Non posare sull'apparecchio sorgenti di fiamme
scoperte quali candele accese.
Smaltire le pile usate in conformità alle norme
governative o disposizioni ambientali vigenti nel
proprio paese o zona.
Lasciare 0,2 metro liberi tutto intorno l'unità.
Non mettere sull'apparecchiatura alcun contenitore
di liquido, come ad esempio dei vasi.
Quando l'interruttore è nella posizione OFF,
l'apparecchiatura non è completamente scollegata
da MAINS.
L’apparecchio va installato in prossimità della
fonte di alimentazione, in modo che quest’ultima
sia facilmente accessibile.
- Non toccare i punti caldi né durante, né
immediatamente dopo l’uso.
- Durante, e subito dopo l’utilizzo, questo prodotto
risulta essere molto caldo in alcune sue parti come
ad esempio i connettori del pannello posteriore.
Non toccare i punti caldi e specialmente la
superficie del pannello. Il contatto con parti calde
può provocare ustioni.
- No se deben colocar sobre el aparato recipientes
que contengan líquidos, como por ejemplo
jarrones.
- Cuando el interruptor está en la posición OFF, el
equipo no está completamente desconectado de
la alimentación MAINS.
- El equipo se instalará cerca de la fuente de
alimentación de manera que resulte fácil acceder
a ella.
Português
- No tocar las áreas calientes mientras la unidad
está en uso ni inmediatamente después.
-
- Mientras esta en funcionamiento e inmediatamente
despues de su uso, este producto presenta zonas
calientes en diversas partes, no exclusivamente
en el sector de los controles o en las conexiones
del panel posterior. No tocar las áreas calientes,
especialmente el panel superior dado que pueden
producirse quemaduras.
-
Nederlands
-
-
-
Español
-
-
ADVERTENCIAS
No exponga el equipo a la lluvia ni a la humedad.
No extraiga la tapa del equipo.
No introduzca nada en el interior del equipo a
través de los orificios de ventilación.
No maneje el cable de alimentación con las
manos mojadas.
No cubra la ventilación con objetos como manteles,
periódicos, cortinas, etc.
No deben colocarse sobre el equipo elementos
con fuego, por ejemplo velas encendidas.
Cuando se eliminen baterías usadas, deben
cumplirse las reglamentaciones oficiales o las
normas de protección medioambiental aplicables
en su país o en su zona.
Deje un espacio de unos 0,2 metro alrededor de la
unidad.
-
-
WAARSCHUWINGEN
Stel het apparaat niet bloot aan regen of vocht.
Verwijder de afdekplaat van het apparaat niet.
Duw niets door de ventilatieopeningen in het
apparaat.
Raak het netsnoer niet met natte handen aan.
Bedek de ventilatieopeningen niet met enige
voorwerpen, zoals tafelkleden, kranten, gordijnen,
enz.
Plaats geen brandende voorwerpen, zoals
kaarsen, op het apparaat.
Volg bij het weggooien van verbruikte batterijen de
overheidswetgeving of milieuvoorschriften op die
van kracht zijn in het land of de regio waarin u zich
bevindt.
Zorg dat er 0,2 meter vrije ruimte rond het toestel
is.
Plaats geen voorwerpen met een vloeistof erin,
zoals een bloemenvaas, op het apparaat.
Als de schakelaar op OFF staat, is het apparaat
niet volledig losgekoppeld van de netspanning
(MAINS).
De apparatuur wordt in de buurt van het stopcontact
geïnstalleerd, zodat dit altijd gemakkelijk
toegankelijk is.
- Raak hete gedeelten van het apparaat niet aan
tijdens en onmiddellijk na het gebruik.
- Tijdens en onmiddellijk na het gebruik is dit
product heet, behalve in de omgeving van de
bedieningstoetsen en de aansluitingen op het
achterpaneel. Raak geen hete plekken aan, vooral
niet het bovenpaneel. Contact met hete plekken
kan brandwonden veroorzaken.
-
-
-
-
-
ADVERTÊNCIAS
Não exponha o equipamento à chuva nem à
humidade.
Não retire a tampa do equipamento.
Não atire nada para dentro do equipamento
através dos orificíos de ventilação.
Não manuseie o cabo de alimentação com as
mãos molhadas.
Não cobrir os orifícios de ventilação com objectos
tais como toalhas de mesa, jornais, cortinas, etc.
Não colocar chamas abertas tais como velas
acesas, sobre o aparelho.
Ao deitar foras as pilhas usadas, favor observar os
regulamentos governamentais ou as regras com
respeito ao meio ambiente que se aplicam no seu
país ou área de residência.
Deixar um espaço de cerca de 0,2 metro ao redor
do aparelho.
Não colocar objectos com líquidos, como vasos,
em cima do equipamento.
Quando o interruptor está na posição OFF, o
equipamento não está desligado completamente
da corrente eléctrica.
O equipamento deve ser instalado perto da fonte
de alimentação para que a mesma seja de fácil
acesso.
- Não toque em focos de luz durante e imediatamente
a seguir à sua utilização.
- Durante e imediatamente a seguir à sua utilização,
este equipamento fica quente em determinadas
áreas com excepção aos controlos e às conexões
do painel traseiro. Não toque em pontos quentes
especialmente no topo do painel. O contacto com
áreas quentes pode causar queimaduras.
Svenska
VARNINGAR
- Utsätt inte utrustningen för regn eller fukt.
- Ta inte bort utrustningens hölje.
- För inte in föremål i utrustningen genom
ventilationshålen.
- Hantera inte nätsladden med våta händer.
- Täck inte för ventilationsöppningarna med
några föremål som till exempel bordsdukar,
dagstidningar, gardiner e.d.
- Inga föremål med öppen låga, som till exempel
tända stearinljus, bör placeras på utrustningen.
- Följ de lagar och miljöskyddsråd som gäller i det
land eller område där du bor när du gör dig av med
batterier.
- Se till att det finns omkring 0,2 meter fri plats runt
omkring enheten.
- Inga objekt som är fyllda med någon vätska,
till exempel blomstervaser, bör placeras på
apparaten.
- Även om strömbrytaren står i det avstängda läget
OFF, så är utrustningen inte helt bortkopplad från
det elektriska nätet (MAINS).
- Utrustningen ska vara installerad nära strömuttaget
så att strömförsörjningen är lätt att tillgå.
- Vidrör inte varma punkter under och omedelbart
efter användning.
- Bortsett från kontrollerna och anslutningsuttagen
på baksidan är den här produkten varm under och
omedelbart efter användning. Vidrör inte varma
punkter och särskilt inte ovansidan. Kontakt med
varma ytor kan orsaka brännskador.
FOREWORD ...........................................1
BASIC OPERATION (PLAYBACK)......25
EQUIPMENT MAINS WORKING SETTING ......................1
SELECTING AN INPUT SOURCE ...................................25
COPYRIGHT ......................................................................1
VIDEO CONVERT ............................................................25
INTRODUCTION ....................................1
SELECTING THE SURROUND MODE...........................26
A NOTE ABOUT RECYCLING ..............1
ADJUSTING THE TONE (BASS & TREBLE) CONTROL .....26
TEMPORARILY TURNING OFF THE SOUND ..................26
FEATURES .............................................3
USING THE SLEEP TIMER .............................................26
FRONT PANEL .......................................4
FL DISPLAY ........................................................................5
REAR PANEL .........................................6
SURROUND MODE .............................27
OTHER FUNCTION ..............................30
TV AUTO ON/OFF FUNCTION........................................30
ATTENUATION TO ANALOG INPUT SIGNAL ..................30
LISTENING THROUGH HEADPHONES .........................30
FUNCTION AND OPERATION ..........................................8
VIDEO ON/OFF ...............................................................30
OPERATION OF REMOTE CONTROL UNIT .................10
DISPLAY MODE ...............................................................30
GENERAL INFORMATION OF RC-1065
SELECTING ANALOG AUDIO INPUT OR
TO DN-A7100 ...................................................................11
DIGITAL AUDIO INPUT ...................................................30
CONNECTIONS ...................................12
RECORDING AN ANALOG SOURCE .............................31
CONNECTING SPEAKERS.............................................13
CONNECTING AUDIO COMPONENTS..........................14
CONNECTING VIDEO COMPONENTS..........................15
HT-EQ (HOME THEATER EQUALIZER) .........................31
7.1 CH INPUT ...................................................................31
AUX2 INPUT.....................................................................32
BASIC OPERATION (TUNER).............32
CONNECTING THE ANTENNA TERMINALS .................17
LISTENING TO THE TUNER ...........................................32
SETUP ..................................................19
PRESET MEMORY ..........................................................33
TROUBLESHOOTING .........................36
AND COMPONENT VIDEO INPUT) ................................20
RS-232C CONTROL SPECIFICATION ....37
3 PREFERENCE .............................................................22
4 SURROUND .................................................................22
5 PL II (PRO LOGIC II) MUSIC PARAMETER ..............23
6 CS II (CIRCLE SURROUND II) PARAMETER ...........23
7 7.1 CH INPUT LEVEL...................................................23
SIMPLE SETUP....................................24
EQUIPMENT MAINS WORKING SETTING
Your DENON product has been prepared to comply
with the household power and safety requirements
that exist in your area.
DN-A7100 can be powered by 230V AC only.
COPYRIGHT
Recording and playback of any material may
require consent. For further information refer to the
following:
—
—
—
—
A NOTE ABOUT
RECYCLING
Copyright Act 1956
Dramatic and Musical Performers Act 1958
Performers Protection Acts 1963 and 1972
Any subsequent statutory enactments and
orders
CAUTIONS ON INSTALLATION
For heat dispersal, leave at least 0.2 m/8 inch of
space between the top, back and sides of this unit
and the wall or other components.
• Do not obstruct the ventilation holes.
0.2 m (8 ins.)
0.2 m
(8 ins.)
0.2 m
(8 ins.)
This product’s packaging materials are recyclable
and can be reused. This product and the accessories
packed together are the applicable product to the
WEEE directive except batteries.
Please dispose of any materials in accordance with
your local recycling regulations.
When discarding the unit, comply with your local
rules or regulations.
Batteries should never be thrown away or incinerated
but disposed of in accordance with your local
regulations concerning chemical wastes.
RDS OPERATION ............................................................35
1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT
2 SPEAKER SETUP........................................................20
Thank you for purchasing the DENON DN-A7100
Surround receiver.
This remarkable component has been engineered
to provide you with many years of home theater
enjoyment. Please take a few minutes to read this
manual thoroughly before you connect and operate
the DN-A7100.
As there are a number of connection and configuration
options, you are encouraged to discuss your own
particular home theater setup with your DENON A/V
specialist dealer.
LIP.SYNC ..........................................................................32
ADVANCED CONNECTING ............................................16
ON SCREEN DISPLAY MENU SYSTEM ........................19
This section must be read before any connection is
made to the mains supply.
NIGHT MODE ..................................................................26
REMOTE CONTROL OPERATION .......8
SPEAKER PLACEMENT .................................................12
INTRODUCTION
ADJUSTING THE MAIN VOLUME ..................................26
DESCRIPTION .......................................2
ACCESSORIES ......................................3
FOREWORD
ENGLISH
TABLE OF CONTENTS
GLOBAL DESCRIPTION..................................................37
0.2 m
(8 ins.)
DETAILED DESCRIPTION ..............................................37
RECOMMENDATIONS OF COMMAND,
STATUS AND LAYER DEFINITION .................................39
RECOMMENDATIONS OF COMMAND,
STATUS AND LAYER .....................................................40
TECHNICAL SPECIFICATIONS ..........43
DIMENSIONS ......................................43
1
ENGLISH
DESCRIPTION
DTS was introduced in 1994 to provide 5.1 channels of
discrete digital audio into home theater systems.
DTS brings you premium quality discrete multichannel
digital sound to both movies and music.
DTS is a multichannel sound system designed to
create full range digital sound reproduction.
The no compromise DTS digital process sets the
standard of quality for cinema sound by delivering
an exact copy of the studio master recordings to
neighborhood and home theaters.
Now, every moviegoer can hear the sound exactly as
the moviemaker intended.
DTS can be enjoyed in the home for either movies or
music on of DVD’s, LD’s, and CD’s.
DTS-ES Extended Surround is a new multichannel
digital signal format developed by Digital Theater
Systems Inc. While offering high compatibility with
the conventional DTS Digital Surround format, DTSES Extended Surround greatly improves the 360degree surround impression and space expression
thanks to further expanded surround signals. This
format has been used professionally in movie
theaters since 1999.
In addition to the 5.1 surround channels (FL, FR, C,
SL, SR and LFE), DTS-ES Extended Surround also
offers the SB (Surround Back) channel for surround
playback with a total of 6.1 channels. DTS-ES
Extended Surround includes two signal formats with
different surround signal recording methods, as DTSES Discrete 6.1 and DTS-ES Matrix 6.1.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
“DTS”, “DTS-ES” and “Neo:6” are trademarks of
Digital Theater Systems, Inc.
The advantages of discrete multichannel systems
over matrix are well known.
But even in homes equipped for discrete multichannel,
there remains a need for high-quality matrix decoding.
This is because of the large library of matrix surround
motion pictures available on disc and on VHS tape; and
analog television broadcasts.
The typical matrix decoder of today derives a center
channel and a mono surround channel from twochannel matrix stereo material. It is better than a
simple matrix in that it includes steering logic to
improve separation, but because of its mono, bandlimited surround it can be disappointing to users
accustomed to discrete multichannel.
The stereo CD is a 16-bit medium with sampling at
44.1 kHz. Professional audio has been 20- or 24bit for some time, and there is increasing interest
in higher sampling rates both for recording and for
delivery into the home. Greater bit depths provide
extended dynamic range. Higher sampling rates
allow wider frequency response and the use of antialias and reconstruction filters with more favorable
aural characteristics.
Neo:6 offers several important improvements as
follow,
• Neo:6 provides up to six full-band channels of
matrix decoding from stereo matrix material. Users
with 6.1 and 5.1 systems will derive six and five
separate channels, respectively, corresponding to
the standard home-theater speaker layouts.
• Neo:6 technology allows various sound elements
within a channel or channels to be steered
separately, and in a way which follows naturally
from the original presentation.
• Neo:6 offers a music mode to expand stereo nonmatrix
recordings into the five- or six-channel layout, in a way
which does not diminish the subtlety and integrity of
the original stereo recording.
2
DTS 96/24 allows for 5.1channel sound tracks to be
encoded at a rate of 96kHz/24bits on DVD-Video
titles.
When DVD-video appeared, it became possible to
deliver 24-bit, 96 kHz audio into the home, but only in
two channels, and with serious limitations on picture.
This capability has had little use.
DVD-audio allows 96/24 in six channels, but a
new player is needed, and only analog outputs are
provided, necessitating the use of the D/A converters
and analog electronics provided in the player.
DTS 96/24 offers the following:
1. Sound quality transparent to the original 96/24
master.
2. Full backward compatibility with all existing
decoders. (Existing decoders will output a 48 kHz
signal)
3. No new player required: DTS 96/24 can be carried
on DVD-video, or in the video zone of DVD-audio,
accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality fullmotion video, for music programs and motion
picture soundtracks on DVD-video.
“DTS” and “DTS 96/24” are trademarks of Digital
Theater Systems, Inc.
Dolby Pro Logic IIx is fully compatible with Dolby
Surround Pro Logic technology and can optimally
decode the thousands of commercially available
Dolby Surround encoded video cassettes and
television programs with enhanced depth and
spatiality. It can also process any high-quality
stereo or Advanced Resolution 5.1-channel music
content into a seamless 6.1- or 7.1-channel listening
experience.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Dolby Digital identifies the use of Dolby Digital audio
coding for such consumer formats as DVD and DTV.
As with film sound, Dolby Digital can provide up
to five full-range channels for left, center, and right
screen channels, independent left and right surround
channels, and a sixth (“.1”) channel for low-frequency
effects.
Dolby Surround Pro Logic II is an improved matrix
decoding technology that provides better spatiality
and directionality on Dolby Surround program
material; provides a convincing three-dimensional
soundfield on conventional stereo music recordings;
and is ideally suited to bring the surround experience
to automotive sound. While conventional surround
programming is fully compatible with Dolby Surround
Pro Logic II decoders, soundtracks will be able to be
encoded specifically to take full advantage of Pro
Logic II playback, including separate left and right
surround channels. (Such material is also compatible
with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output
channels from 5.1-channel sources. This is done
using a matrix decoder that derives three surround
channels from the two in the original recording. For
best results, Dolby Digital EX should be used with
movies soundtracks recorded with Dolby Digital
Surround EX.
About Dolby Pro Logic IIx
Dolby Pro Logic IIx technology delivers a natural
and immersing 7.1-channel listening experience
to the home theater environment. A product of
Dolby’s expertise in surround sound and matrix
decoding technologies, Dolby Pro Logic IIx is a
complete surround sound solution that maximizes
the entertainment experience from stereo as well as
5.1-channel encoded sources.
Circle Surround II (CS-II) is a powerful and versatile
multichannel technology. CS-II is designed to enable
up to 6.1 multichannel surround sound playback
from mono, stereo, CS encoded sources and other
matrix encoded sources. In all cases the decoder
extends it into 6 channels of surround audio and a
LFE/subwoofer signal. The CS-II decoder creates a
listening environment that places the listener “inside”
music performances and dramatically improves
both hi-fi audio conventional surround-encoded
video material. CS-II provides composite stereo rear
channels to greatly improve separation and image
positioning – adding a heightened sense of realism
to both audio and A/V productions.
CS-II is packed with other useful feature like dialog
clarity (SRS Dialog) for movies and cinema-like bass
enrichment (TruBass). CS-II can enable the dialog
to become clearer and more discernable in movies
and it enables the bass frequencies contained in
the original programming to more closely achieve
low frequencies – overcoming the low frequency
limitations of the speakers by full octave.
Circle Surround II, Dialog Clarity, TruBass, SRS and
symbol are trademarks of SRS Labs, Inc.
Circle Surround II, Dialog Clarity and TruBass
technology are incorporated under license from SRS
Labs, Inc.
HDCD® (High Definition Compatible Digital ®) is a
patented process for delivering on Compact Disc the
full richness and details of the original microphone
feed.
HDCD encoded CDs sound better because they are
encoded with 20-bits of real musical information as
compared to 16-bits for all other CDs.
HDCD overcomes the limitation of the 16-bit CD
format by using a sophisticated system to encode
the additional four bits onto the CD while remaining
completely compatible with the CD format.
When listening to HDCD recordings, you hear more
dynamic range, a focused 3-D sound stage, and
extremely natural vocal and musical timbre. With
HDCD, you get the body, depth and emotion of the
original performance not a flat, digital imitation.
HDCD system manufactured under license from
Microsoft. This product is covered by one or more
of the following: In the United States 5,479,168
5,638,074 5,640,161 5,808,574 5,838,274 5,854,600
5,864,311 5,872,531 and in Australia 669,114 with
other patents pending.
HDMI, the
and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
The DN-A7100 incorporates the latest generation of
digital surround sound decoding technology such as
Dolby Digital EX, Dolby Digital, DTS-ES (Discrete
6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music),
Dolby Pro-Logic IIx (Movie, Music and Game), Circle
Surround II (Cinema and Music).
In addition, DENON has focused on the future.
By utilizing pre-out jacks, 7.1 direct inputs and a
RS-232C communication port, the DN-A7100 is
tomorrow’s technology, today!
The DN-A7100 incorporates the most advanced
Digital Signal Processing circuitry, along with a
Crystal® 192 kHz/24 bit D/A converter in each of
the 7 channels. Independent power supply circuits
are incorporated for the FL display, audio and
video sections for maximum separation, clarity
and dynamic range. Together with hand-selected
customized components, all elements work in
harmony to recreate the emotion, exactly as the artist
had intended.
The DN-A7100 is designed and engineered with
extensive feedback from custom installation experts,
dealers and consumers. It features multisource,
a RS-232C communication port and an extensive
array of both analog and digital inputs / outputs. With
6 assignable digital inputs (including Front Aux), 3
assingnable component inputs, SACD Multi Channel
(7.1 channel) direct inputs video convert system
and OSD output versatility is taken to a stunning
new level. Furthermore, the DN-A7100 can output
the OSD information through the Y/C (S-video) and
composite video outputs.
This unit has Simple Setup function for easy setup.
You can setup all speaker settings by just selecting
your room size and the number of your speakers with
Simple Setup function. You can also setup customized
settings just like conventional AV amplifiers.
• Dolby Digital EX, Dolby Digital ,
DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6)
• Dolby Pro Logic IIx (Movie, Music, Game)
• Circle Surround II (Movie, Music, Mono)
• HDCD decording
• 192 kHz/24 bit Crystal® DAC for all 8 Channels
• 32 bit Digital Surround Processing Chipsets
• Video Off Mode
• RS-232C Terminal for System Control
• Set Up Menu via all Video Output (Composite, SVideo and Component video)
• Auto Input Signal Detection
• Improved Station Name Input Method, 50 Presets
• Auto Adjust Function for Speaker Distance Settings
(Delay Time)
• XLR type Balanced Audio Input (AUX Input)
• Remote control
• Simple Setup Function
• Video convert system
• LIP.SYNC Funciton (Audio delay)
• XLR type Balanced Audio Output
ENGLISH
FEATURES
ACCESSORIES
Remote Controller RC-1065
AAA-size batteries × 2
AM Loop Antenna
FM Antenna
AC Power Cord
An easy-to-use universal remote control allows full
access to all of the operating functions.
User Guide
Service Station List × 1
3
ENGLISH
!0
FRONT PANEL
q
w e t ui o
r y
!0
!1
MUTE button
!1
!9
VOLUME control knob
Adjusts the overall sound level. Turning the control
clockwise increases the sound level.
ATT (Attenuate) button
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK indicator will illuminate. If this happens, you
should press the ATT button. “ATT” is displayed
when this function is activated.
The signal-input level is reduced by about half.
Attenuation will not work with the output signal of
“REC OUT” (TAPE, CD-R/MD and VCR output). This
function is memorized for each input function.
q
!3
!4
POWER switch and STANDBY
indicator
Press the button to turn the power ON, and press
again to turn it OFF. If the POWER switch is in the
ON position, the power of this unit can be turned ON/
OFF by pressing the POWER button on the remote
control unit.
When this unit is in the standby mode with the
POWER switch set to the ON position, pressing the
ENTER button also allows to turn the power on.
The STANDBY indicator lights up when this unit
is the standby mode (power OFF) by the remote
control unit.
w
KEY LOCK button
Press and hold this button for 3 seconds to set
KEY LOCK mode. When the KEY LOCK mode is
on, the unit can only be operated from the RS232C
or remote control, and operation by the main unit
keys is prohibited. Press and hold this button for 3
seconds to release the KEY LOCK mode.
e
KEY LOCK indicator
The indicator is illuminated when in KEY LOCK
mode.
4
!3
r
!2
SURROUND MODE button
You can select the surround mode by pressing this
button.
t
HDMI indicator
This indicator is illuminated when HDMI device is
connected to the DN-A7100.
y
INFRARED receiving sensor
window
This window receives infrared signals for the remote
control.
u
BAND button
Press this button to switch between FM and AM in
the TUNER mode.
i
T-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
(See page 33)
o
MENU button
This button is used to enter the SETUP MAIN
MANU.
CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 33)
!2
@2 @0 !8 !6
@3 @1 !9 !7 !5
!8
Press this button to mute the PreAMP output. Press it
again to return to the previous volume level.
INPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources.
The video SOURCE, such as TV, DVD, VCR1 and
DSS, selects video and audio simultaneously.
Audio function sources such as CD, TAPE, CDR/MD,
and TUNER may be selected in conjunction with a
Video source.
This feature (Sound Injection) combines a sound
from one source with a picture from another.
Choose the video source first, and then choose a
different audio source to activate this function.
!4
Cursor (1, 2, 3, 4) / ENTER button
Use these buttons when operating the SETUP MAIN
MENU and TUNER function.
!5
EXIT button
This button is used to exit from the SETUP MAIN
MENU.
!6
SIMPLE SETUP button
Press this button to enter the simple setup mode.
You can setup the speaker conditions (speaker sizes,
number of speakers, speaker delay times) quickly by
pressing the cursor buttons.
!7
DISPLAY button
When this button is pressed, the FL display mode
is changed as Surround Mode → Auto-display Off
→ Display Off → Input Function and the display off
indicator(DISP) lights up in condition of DISPLAY
OFF.
HT-EQ button
Used to turn on or off HT(Home Theater)-EQ mode.
This mode compensates for the audio portion of
a movie sounding “bright”. When this button is
pressed, “EQ” indicator lights up.
@0
MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 33)
@1
PURE DIRECT button
When this button is pressed once, “SOURCE DIRECT”
appears on the FL display. If pressed again, “PURE
DIRECT” appears. After 2 seconds, the FL display
indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct/source direct function
is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
@2
AUTO (Auto surround) button
Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the
receiver determines the surround mode corresponding
to a digital input signal automatically.
@3
HEADPHONE jack for stereo
headphones
This jack may be used to listen to the DN-A7100’s
output through a pair of headphones. Be certain
that the headphones have a standard 1 / 4” stereo
phono plug.
s
d
a
DISP
¡6
SLEEP
g
AUTO
AUTO SURR
TUNED
DIRECT
ST
V – OFF
DISC 6.1
This indicator lights when a digital input has been
selected.
j k ¡0
¡2
l ¡1
h
f
NIGHT
MT X 6.1
PEAK
ATT
EQ
¡3
SURROUND
DIGITAL
DIGITAL
L
C
¡7
DISP (Display Off) indicator
h
S
¡4
V (video)-OFF mode indicator
This indicator is illuminated when the Video-OFF
function is active.
s
j
SLEEP timer indicator
d
AUTO SURR (Auto Surround
mode) indicator
This indicator is illuminated to show that the AUTO
SURROUND mode is in use.
f
TUNER’s indicators
AUTO : This indicator illuminates when the
tuner’s Auto mode is in use.
TUNED : This indicator illuminates when the
tuner receives a sufficiently strong
radio signal.
ST(Stereo) : This indicator illuminates when an
FM station is being tuned into stereo
condition.
g
DTS-ES mode indicators
(DISC6.1, MTX6.1)
NIGHT mode indicator
This indicator is illuminated when the DN-A7100 is in
the Night mode, which reduces the dynamic range of
digital program material at low volume levels.
k
PEAK indicator
This indicator is a monitor for an analog audio input
signal. If the selected analog audio input signal is
greater than the capable level of internal processing,
this will illuminate. If this happens, you should press
the ATT button on the remote.
l
EQ mode indicator
This indicator is illuminated when the HT-EQ function
is active.
¡0
This indicator is illuminated when an analog input
source has been selected.
¡3
SR
This indicator is illuminated when the DN-A7100 is in
the display off condition.
This indicator is illuminated when the sleep timer
function in the main-room is in use.
ANALOG input indicator
R
LFE
SL
a
¡2
ANALOG
PCM
¡5
DIGITAL Input Indicator
ENGLISH
¡1
FL DISPLAY
ATT (Attenuation) indicator
This indicator is illuminated when the attenuation
function is active.
SIGNAL FORMAT indicators
2 DIGITAL, EX, 2 SURROUND, dts, ES, 96/24,
PCM
When the selected input is a digital source, some
of these indicators will be illuminated to display the
specific type of signal in use.
¡4
ENCODED CHANNEL STATUS
indicators
These indicators display the channels that are
encoded with a digital
input signal. If the selected digital input signal is
Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”,
“SR” and “LFE” will be illuminated.If the digital input
signal is 2 channel PCM-audio, “L” and “R” will be
displayed.
If Dolby Digital 5.1ch signal with Surround EX flag or
DTS-ES signal comes in, “L”, “C”, “R”, “SL”, “S” , “SR”
and “LFE” will be illuminated.
¡5
Main Information Display
This display shows messages relating to the status,
input source, surround mode, tuner, volume level or
other aspects of unit’s operation.
¡6
DIRECT (Puredirect) indicator
This indicator is illuminated when the DN-A7100 is in
the SOURCE DIRECT or PURE DIRECT mode.
¡7
HDCD indicator
When HDCD signal is decoded from digital input, this
indicator will light up.
These indicators will illuminate to show the DTS-ES
decoding mode (Discrete 6.1 or Matrix 6.1).
5
ENGLISH
t
REAR PANEL
q
w
e
r
t
y
u
i
MONITOR OUT
This is a monitor output and each one includes both
composite video and S-video configurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
i
o
y
!7 !6
q
!5 !4
!3
7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, SACD
multichannel player, or other components that has
a multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
w
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
!2
e
AM antenna and ground terminals
6
!0 o
AUDIO IN/OUT (CD, TAPE, CD-R/
MD, TV, DVD, VCR, DSS/VCR2)
These are the analog audio inputs and outputs. There
are 7 audio inputs (4 of which are linked to video
inputs) and 3 audio outputs (1 of which are linked to
video outputs). The audio jacks are nominally labeled
for cassette tape decks, compact disc players, DVD
players and etc.... The audio inputs and outputs
require RCA-type connectors.
r
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
!1
VIDEO IN/OUT
(TV, DVD, VCR, DSS/VCR2)
These are the video inputs and outputs. There
are 4 video inputs and 1 video outputs and each
one includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The video output channel can be used to be
connected to video tape recorders for making
recordings.
The input signals of video and S-video are converted
each other, and each of the converted video signals
can be output.
COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the DN-A7100.
The DN-A7100 has two component video input
connectors to obtain the color information (Y, CB,
CR) directly from the recorded DVD signal or other
video component and one component video output
connector to output it directly into the matrix decoder
of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
u
DIGITAL INPUT (Dig.1-5) /
OUTPUT (coaxial, optical)
These are the digital audio inputs and outputs. There
are 2 digital inputs with coaxial jacks, 3 with optical
jacks.
The inputs accept digital audio signals from a CD,
DVD, or other digital source component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD recorders,
CD recorders, or other similar components.
HDMI INPUT/OUTPUT
This unit has 2 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 20)
AC INLET
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
DN-A7100 can be powered by 230V AC only.
!0
DC TRIGGER output terminal
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
This output voltage is for (status) control only, It is not
sufficient for drive capability.
!1
Analog audio output level switch
(-10dBV/+4dBu)
This switch changes the standard output level of the
Balanced Analog audio signal.
!2
Balanced Analog audio output
(L, R, SL, SR, SBL, SBR, C, SW)
Balanced Analog audio output (XLR) for L (front
left), R (front right), C (Center), SL (surround left),
SR (surround right), SBL (surround back left), SBR
(surround back right) and SW (subwoofer).
Use these jacks for connection to external power
amplifiers.
!3
Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifier is used,
connect this jack to the subwoofer amplifier input. If
you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifier, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifier.
AUX1 analog audio input level
switch (-10dBV/+4dBu)
ENGLISH
!4
This switch changes the standard input level of the
AUX1 Balanced Analog audio signal.
!5
AUX1 analog audio input jacks
(L/R)
These auxiliary analog audio input jacks accept the
connections with analog audio signal output jacks
(XLR jacks) of other audiovisual devices.
!6
AUX1 VIDEO / DIGITAL AUDIO
INPUT
These auxiliary video/audio input jacks accept the
connections of a camcorder, portable DVD etc.
!7
RS-232C
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
DN-A7100 by using an external device.
7
ENGLISH
REMOTE CONTROL
OPERATION
FUNCTION AND OPERATION
Used to remotely control the unit. You can switch
between functions by pressing either the AMP or
TUNER source buttons.
z
POWER buttons
This buttons is used to turn the DN-A7100 on or off.
b
CL (Clear) button
(When TUNER mode is selected)
Used to call up SETUP MAIN MENU and adjust
speaker levels or 7.1 ch input level.
Selects the display mode for the front display of the
DN-A7100.
n
⁄5
c
(When TUNER mode is selected)
Used to select a preset station up and down.
x
DISPLAY button
SLEEP button
m
‹2
v
b
n
v
⁄6
⁄7
.
⁄0
⁄1
⁄2
⁄3
⁄4
⁄5
These buttons are used to switch between 0 to 9 of
the source components.
If the source is set to the AMP (amplifier), these
buttons are used to perform operations.
(When AMP mode is selected)
⁄9
1/AUTO button
Used to select auto surround.
m
,
Numeric buttons
⁄8
¤0
¤1
¤2
¤3
¤4
¤5
¤6
¤7
¤8
¤9
‹0
‹1
2/Dolby button
Used to select DOLBY mode.
3/dts button
Used to select dts mode.
4/CSII button
Used to select CSII mode.
PRESET +/– buttons
INFO button
(When AMP mode is selected)
When this button is pressed, the current setting are
displayed on the TV monitor.
1, 2, 3, 4 (CURSOR) / ENTER buttons
(When AMP mode is selected)
These buttons are used when controlling the cursor
of the DN-A7100.
.
CH/CAT3 (UP) / 4 (DOWN) buttons
(When TUNER mode is selected)
These buttons are used to change channels.
Not used on this unit.
9/NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This function
reduces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
P.DIRECT button
When this button is pressed, the tone control circuit
is bypassed.
⁄7
SURROUND button
T.TONE button
(When AMP mode is selected)
Used to enter the test tone menu.
6/VIRTUAL button
Used to select VIRTUAL mode.
8/STEREO button
Used to select STEREO mode.
Note:
Select the AMP as the source to use this remote
controll with the DN-A7100.
This button is used to selects the surround mode.
⁄0
7/M-CH ST button
Used to select Multi Channel Stereo.
SOURCE button
These buttons are used to switch the source of your
A/V Receiver / amplifer. Each time a source button is
pressed, the remote control changes to the source
which was pressed.
⁄6
,
5/EX/ES button
Used to select EX/ES mode.
0/7.1CH IN button
Press this button to select the output of an external
multi channel decoder.
8
CH. SEL button
(When TUNER mode is selected)
This button is used to erase the memory or program
of a source.
This button is used for setting the sleep timer.
z
x
c
⁄4
⁄8
BAND/LIP SYNC button
(When TUNER mode is selected)
Used to select a radio band.
(When AMP mode is selected)
Used to select LIP SYNC mode.
⁄9
T-MODE button
These buttons are used to adjust the tone control
of low frequency sound for left, right and subwoofer
speaker.
(When TUNER mode is selected)
Used to select auto stereo mode or mono mode
when the FM band is selected.
The “AUTO” indicator lights in the auto stereo
mode.
⁄2
¤0
⁄1
BASS +/- buttons
XMCAT button
(When TUNER mode is selected)
Press this button is used to select the XM Category
mode.
Not used on this unit.
⁄3
F.DIRECT button
(When TUNER mode is selected)
Used to select the "Frequency direct input".
P-SCAN button
(When TUNER mode is selected)
Used to start preset scan.
MEMO/HT-EQ button
(When TUNER mode is selected)
This button is used to store setting to memory or
program a source.
(When AMP mode is selected)
Used to turn on or off HT(Home Theater)-EQ mode.
This mode compensates for the audio portion of a
movie sounding “bright”.
When this button is pressed, “EQ” indicator light up.
¤2
A/D button
(When AMP mode is selected)
Used to switch between the analog and digital
inputs.
¤3
TUNING +/– buttons
(When TUNER mode is selected)
Used to tune a frequency station up and down.
¤4
MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN
MENU of the DN-A7100.
¤5
VOLUME +/– buttons
This button is used to adjust the volume for the
amplifier.
¤6
EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup
menu.
¤7
¤8
ATT button
ENGLISH
¤1
(When AMP mode is selected)
When the input signal is too high and the voice
distorts even by throttling the DN-A7100 VOLUME
control, turn on this function.
“ATT” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the
output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is
selected.
¤9
TREBLE +/- buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
‹0
T-DISP button
(When TUNER mode is selected)
Used to select the display mode in RDS.
‹1
PTY/V-OFF buton
(When TUNER mode is selected)
Used to display the programme type information of
the current station.
(When AMP mode is selected)
Used to turn off the video signal.
‹2
Infrared Transmitter
This transmitter emits infrared light. Press the
buttons while pointing the transmitter towards the
infrared receiver window of the DN-A7100.
MUTE button
This button is used to mute the audio for the
amplifier.
9
ENGLISH
OPERATION OF REMOTE CONTROL UNIT
REMOTE CONTROL
The distance between the transmitter of the remote
control and the IR SENSOR of the DN-A7100 should
be less than 5 meters. If the remote control is pointed
in a direction other than the IR SENSOR or if there is
an obstacle between them, use of the remote control
may not be possible.
LOADING BATTERIES
CAUTIONS ON BATTERIES
The life of the batteries used with the remote control
is about 4 months with normal use. Also be sure to
replace batteries earlier when you notice that they
are getting weak.
• Use “AAA” type batteries in this remote control
unit.
• We recommend that you use alkali batteries.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as
possible.
• When inserting the batteries, be careful to do so in
the proper direction, following the + and - marks in
the remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with correct
and
polarity.
3.
Close the cover until it clicks.
Remote-controllable range
DN-A7100
x. 5
m
o
ppr
A
60°
Remote control unit (RC-1065)
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
10
ENGLISH
GENERAL INFORMATION OF RC-1065 TO DN-A7100
To control the DN-A7100 by your RC-1065, you have to select the device AMP or TUNER by pressing the
SOURCE button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
TUNER MODE
POWER
SLEEP
DISPLAY
P-DIRECT
SURROUND
AUTO (1)
DOLBY (2)
dts (3)
BAND/LIP SYNC
CSII (4)
EX/ES (5)
VIRTUAL (6)
M-CH ST (7)
STEREO (8)
NIGHT (9)
7.1ch IN (0)
A/D
MEMO/HT-EQ
INFO
MENU
CURSOR 1 / 3 / 4 / 2
ENTER
T-TONE
EXIT
VOL+
VOLATT
MUTE
BASSBASS+
TREBLETREBLE+
PTY/V-OFF
CH-SEL
AUX1
AUX2
TUNER
TV
DVD
VCR
DSS/VCR2
CD
TAPE
CDR/MD
Turns the DN-A7100 on and off
Sets the sleep timer function
Changes the front display mode
Selects the pure direct mode
Selects the surround mode
Selects auto surround
Selects DOLBY mode
Selects dts mode
Select LIP SYNC mode
Selects CS2 mode
Selects EX/ES
Selects VIRTUAL mode
Selects the Multi Channel Stereo
Selects STEREO mode
Turns on or off NIGHT mode
Selects the 7.1ch input ports
Switches between the analog or digital inputs
Turns on or off HT-EQ mode
Turns on or off the “On Screen Display”
Display the current setting on the monitor
Moves the cursor for setting in “On Screen Display”
Enters the “On Screen Display”
Confirms the setting in “On Screen Display”
Enters the test tone menu
Exits from SETUP MENU
Adjusts up to the over all sound level
Adjusts down to the over all sound level
Reduces the analog input level
Decreases the sound temporarily
Adjusts down to the tone control of low frequency sound
Adjusts up to the tone control of low frequency sound
Adjusts down to the tone control of high frequency sound
Adjusts up to the tone control of high frequency sound
Turns on or off Video output
Calls up SETUP MENU and adjusts speaker level or 7.1ch input level
Input source select AUX1
Input source select AUX2
Input source select TUNER
Input source select TV
Input source select DVD
Input source select VCR
Input source select DSS/VCR2
Input source select CD
Input source select TAPE
Input source select CDR/MD
0-9
BAND/LIP SYNC
T-MODE
P-SCAN
CL
MEMO/HT-EQ
PRESETPRESET+
TUNINGTUNING+
INFO
F-DIRECT
T-DISP
PTY/V-OFF
AMP
Inputs the numeric
Select a radio band
Selects the auto stereo mode or mono mode
Starts preset scan
Clears the input data
Enters the tuner preset memory numbers
Selects a preset station down
Selects a preset station up
Tunes a frequency station down
Tunes a frequency station up
Shows preset information
Selects the “Frequency direct input”
Selects the display mode in RDS
Turns PTY group or type search mode on or off
Select AMP mode
* POWER, SLEEP, DISPLAY, P-DIRECT, SURROUND, VOL+, VOL–, MUTE, BASS+,
BASS–, TREBLE+, and TREBLE- keys can be selected in TUNER mode the same
as in AMP mode.
11
ENGLISH
CONNECTIONS
Front left and right speakers
We recommend to set the front L and R speakers
with 45-60 degrees from the listening position.
SPEAKER PLACEMENT
Center speaker
Align the front line of the center speaker with the front
L/R speakers. Or place the center speaker a little
backward from the line.
The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers,
a center speaker, surround left and right speakers,
a surround back left and right speakers, and a
subwoofer.
For best results we recommend that all front speakers
be of the same type, with identical or similar driver
units. This will deliver smooth pans across the front
sound stage as the action moves from side to side.
Your center channel speaker is very important as
over 80% of the dialog from a typical motion picture
emanates from the center channel.
It should possess similar sonic characteristics to the
main speakers. Surround channel speakers need not
be identical to the front channel speakers, but they
should be of high quality.
The surround back speaker is useful for playback
of Dolby Digital Surround EX or DTS-ES. One of
the benefits of both Dolby Digital and DTS is that
surround channels are discrete full range, while they
were frequency limited in earlier “Pro Logic’ type
systems.
Bass effects are an important part of home theater.
For optimal enjoyment a subwoofer should be used
as it is optimized for low frequency reproduction. If
you have full range front speakers, however, they
may be used in place of a subwoofer with proper
setting of the switches in the menu system.
Surround Left
Subwoofer
Front Left
Surround Back
Left
Front Center
0°
Surround Back
Right
22°
150°
30°
135°
110°
12
Surround Right
90°
Front Right
Surround left and right speakers
When the DN-A7100 is used in surround operation,
the preferred location for surround speakers is on
the side walls of the room, at or slightly behind the
listening position.
The center of the speaker should face into the
room.
Surround back left and right speakers
Surround back speakers are required when a full 7.1channel system is installed.
Speakers should be placed on a rear wall, behind the
listening position.
The center of the speaker should face into the
room.
HEIGHT OF THE SPEAKER UNITS
Front left and right speakers, and a center speaker
Align the tweeters and mid-range drivers on the
three front speakers at the same height, as best as
possible.
Surround left and right speakers, and surround
back speaker
Place the surround left, right and surround back
speakers higher than your ears by about 70cm – 1m.
Also place the speakers at the same height, as best
as possible.
70cm
1m
Subwoofer
We recommend using a sub-woofer to have
maximum bass effect. As the subwoofer only handles
low frequencies, its placement is not of particular
importance when used indoors.
Note:
Use magnetically-shielded speakers for front left, right
and the center speakers when the speakers are installed
near the TV.
Passive
subwoofer
INVERT
OUTPUT
INPUT
INPUT
LEVEL
BTL
EXT. CONT. IN
Surround
BACK
Right
Left
Powered
subwoofer
Power
Amplifier
HOT
MA X
VIDEO/
+5~13V DC
SYSTEM OUT
OUT
or
IN
GND
1
GND
3
COLD
REMOTE CONT.
MASTER SLAVE
MIN
2
F US E
INPUT
1
2
HOT
3
COLD
ENGLISH
XLR terminals are used for balanced inputs and
outputs.
CONNECTING SPEAKERS
OUTPUT
SPEAKER SYSTEM
MINIMUM 4 OHMS
CONNECTING A SUBWOOFER
Use the SW OUT jack (RCA-type connector) to
connect a powered subwoofer (power amplifier built
in).
If your subwoofer is a passive type (power amplifier
is not built in), connect a monaural power amplifier to
the SW OUT jack (RCA-type connector) and connect
the subwoofer to the amplifier.
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
R
SUB WOOFER
L
FRONT
R
L
SURROUND BACK
R
L
SURROUND
CENTER
INPUT
Main Amplifier
Center
Passive
subwoofer
Right
Left
Front
Right
Left
Surround
13
ENGLISH
CONNECTING AUDIO COMPONENTS
DIGITAL
INPUT
DIGITAL
OUTPUT
Tape Deck
CD player
CD recorder
DIGITAL OUT
OUTPUT
L
L
L
R
R
R
OUT IN
OUT IN
L
L
R
R
R L
R L
R L
L R
Analog Audio
L R
L R
L R
L R
L R
Digital Audio (coaxial)
Digital Audio (optical)
R L
The output audio signal from the TAPE OUT jack and
the CD-R/MD OUT jack is the same signal which is
currently selected.
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
14
R L
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 6 digital inputs, 2 coaxial jacks and 4
optical jacks (include AUX) , on the rear panel. You
can use these jacks to input PCM, Dolby Digital
and DTS bitstream signals from a CD, DVD, or
other digital source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These jacks
can be connected to a CD recorder-, or a MD deck
inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2,3 or
AUX1 (OPT) input jacks. Use 75 ohms coaxial
cables (for digital audio or video) for DIG-4,5 input
jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 20.
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.
There are 3 types of video jacks on the rear panel.
DVD player
AUDIO
OUT
S-VIDEO VIDEO
OUT
OUT
COMPONENT
VIDEO OUT
Y
CB / PB CR / PR
AUDIO
OUT
COMPONENT S-VIDEO
VIDEO IN
IN
Y
S-VIDEO
OUT
VIDEO jack
The video signal for the VIDEO jacks is the
conventional composite video signal.
S-VIDEO jack
The video signal is separated into luminance (Y) and
color (C) signals for the S-VIDEO jack. The S-VIDEO
signals enables high-quality color reproduction. If
your video component has an S-VIDEO output, we
recommend to use it. Connect the S-VIDEO output
jack on your video component to the S-VIDEO input
jack on this unit.
DIGITAL
OUT
CB / PB CR / PR
L R
L R
L
L
VIDEO
OUT
R
R
Component jack
Make component video connections to a TV or
monitor with component inputs to produce higher
quality video images. Use a component video cable
or 3 video cords to connect the component video out
jacks on the DN-A7100 to the monitor.
R L
L
R
L R
L R
R L
Video
R L
Video
S-VIDEO
S-VIDEO
L R
Analog Audio
L R
S-VIDEO
OUT IN
AUDIO
OUT
AUDIO
IN
L R
L R
VIDEO
OUT IN
Digital Audio
(coaxial)
Analog Audio
VIDEO
OUT
AUDIO
OUT
S-VIDEO
IN
VIDEO
IN
L R
L R
L R
DIGITAL
OUT
Satellite Tuner
VIDEO PROJECTOR
Digital Audio
(coaxial)
L R
Digital Audio
(optical)
ENGLISH
VIDEO, S-VIDEO , COMPONENT JACKS
CONNECTING VIDEO COMPONENTS
Digital Audio
(optical)
Notes:
• Be sure to connect the left and right audio channels
properly.
Red connectors are for the R (right) channel, and
white connectors are the for L (left) channel.
• Be sure to connect the inputs and outputs of the
video signals properly.
• If you connect the S-VIDEO or component signal
to the S-VIDEO or component jack on this unit, it
is not necessary to connect the conventional video
signal to the VIDEO (composite) jack. If you use
both video inputs, this unit gives priority to the SVIDEO signal.
• Each type of video jack works independently.
Signals input to the VIDEO (composite) and SVIDEO jacks or component are output to the
corresponding VIDEO (composite) and S-VIDEO
or component jacks, respectively.
• This unit has the “TV-AUTO ON/OFF” function to
turn the TV ON or OFF automatically, by sensing
the incoming video signal from the VIDEO jacks.
• You may need to setup the digital audio output
format of your DVD player, or other digital source
components. Refer to the instructions of the each
component connected to the digital input jacks.
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator with a Dolby Digital
decoder to connect a video disc player which has a
Dolby Digital RF output jack to the digital input jack
on this unit.
VCR
TV
15
ENGLISH
ADVANCED CONNECTING
L R
L R
L R
R L
R L
R L
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
NEUTRIK
CENTER
INPUT
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
Power
Amplifer
Subwoofer
DVD Audio player
or
Super Audio CD Multi
channel player
Front
Front
Center
Right
Left
Surround
Surround
Left
Right
Surround
Back Left
16
Surround
Back Right
CONNECTING MULTI CHANNEL AUDIO SOURCE
CONNECTING AN EXTERNAL POWER AMPLIFIER
The 7.1CH INPUT jacks are for multichannel audio
source such as a SACD multichannel player, DVD
audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 23.
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
FM Antenna
AM Loop
Antenna
FM External
Antenna
AM External
Antenna
Connecting the supplied FM antenna
The supplied FM antenna is for indoor use only.
During use, extend the antenna and move it in various
directions until the clearest signal is received.
Fix it with push pins or similar implements in the
position that will cause the least amount of distortion.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
ENGLISH
CONNECTING THE SUPPLIED ANTENNAS
CONNECTING THE ANTENNA TERMINALS
Connecting the supplied AM loop antenna
The supplied AM loop antenna is for indoor use
only.
Set it in the direction and position it to where you
receive the clearest sound. Put it as far away as
possible from the unit, televisions, speaker cables,
and power cords.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
1.
Press and hold down the lever of the AM
antenna terminal.
2.
3.
Insert the bare wire into the antenna terminal.
Release the lever.
CONNECTING AN FM OUTDOOR ANTENNA
ASSEMBLING THE AM LOOP ANTENNA
1.
Release the vinyl tie and take out the connection
line.
4.
Place the antenna on stable surface.
Notes:
• Keep the antenna away from noise sources (neon
signs, busy roads, etc.).
• Do not put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
CONNECTING AN AM OUTDOOR ANTENNA
2.
Bend the base part in the reverse direction.
An outdoor antenna will be more effective if it is
stretched horizontally above a window or outside.
Notes:
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
3.
Insert the hook at the bottom of the loop part
into the slot at the base part.
17
ENGLISH
HDMI JACK
This unit has two HDMI inputs and one HDMI output. It
can send digital video and audio signals from DVDs and
other sources directly to a display. It minimizes signal
degradation caused by analog conversion so that high
quality images can be enjoyed.
Select an input source from the OSD menu system.
(See page 20)
Notes:
• When the HDMI output is connected to a display
monitor that does not support HDCP, signals are not
output. To view images in HDMI, it is necessary to
connect to a display that supports HDCP.
• There may be no image output if connected to a
TV or display that is not compatible with the above
format.
• Refer to the instruction manual of the TV or display
to be connected to the DN-A7100 for detailed
information regarding the HDMI terminal.
* HDCP: High-bandwidth Digital Content Protection
• Disconnecting or connecting cables with the power
on can damage the equipment. Turn the power off
before disconnecting or connecting cables.
• Some DVD-Audio disks disable downmixing.
These types of disks are not played back correctly
unless the left, center, right and surround left and
right speakers, and subwoofer are connected.
• If a DVD player that does not support HDMI 1.1 is
connected to the DN-A7100, multi channel PCM
playback is not possible even with DVD-Audio
disks.
• If a DVD player or other device with DVI output is
connected to the DN-A7100, a separate audio cable
(optical-digital, coaxial digital or analog) is needed
for the audio signals. In this case, select the connected
audio input as explained in “1 INPUT SETUP”. (See
page 20)
• Multi channel PCM signals and audio signals of 62
kHz or higher that are input from the HDMI jack are
not output from the DIGITAL OUT jacks.
• Depending on the quiality of the cable used, the
HDMI signal may be affected by noise.
• Audio units that use sampling frequencies of 128
kHz and above are not supported.
DVD player
HDMI OUTPUT
CONNECTING HDMI DEVICES
An HDMI cable (sold separately) is used to connect
the HDMI jack on the DN-A7100 with the HDMI jack
on a DVD player, TV, projector or other component. To
transmit multichannel audio via HDMI, the connected
player must support multichannel audio transmission
through its HDMI jack.
HDMI video streaming is compatible with DVI in
principle. Therefore, it is possible to connect to a TV
or monitor that has a DVI terminal using an HDMI-DVI
conversion cable or plug. When connecting to a DVI
terminal, connect the audio signal separately.
Notes:
• Some HDMI components can be controlled over the
HDMI cable, but this receiver cannot control other
components this way.
• When connected to a monitor (i.e., TV, projector,
etc.) that does not support HDCP, video and audio
are not output.
• DVI cables come with 24-pin and 29-pin plugs. This
receiver supports 24-pin DVI-D cables; 29-pin DVI
cables cannot connect to it.
• Some source devices such as DVD players does not
support HDMI repeater like those of the DN-A7100.
In such case, pictures are not properly projected on
monitors such as TVs and projectors.
• When multiple components are connected to this
receiver, turn power to unused components off to
prevent interference between them.
18
Satellite Tuner
HDMI OUTPUT
VIDEO PROJECTOR
HDMI INPUT
After all components are connected, initial setup
must be performed.
ON SCREEN DISPLAY MENU SYSTEM
The DN-A7100 incorporates an on-screen menu
system, which makes various operations possible by
using the cursor (3, 4, 1, 2) and ENTER buttons on
the remote control or on the front panel.
Note:
To view the on-screen displays, make certain you have
made a connection from the Monitor Out jack on the
rear panel to the composite, S-Video, component video
input of your TV or projector. (see page 15)
1.
Press the AMP button of the remote control.(This
step is not needed when operating the setup
menus from the receiver itself.)
2.
Press the MENU button on the remote control
or set to display the “SETUP MAIN MENU” of
the OSD menu system.
SETUP MAIN MENU
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 3 : : DVD :AUTO : 1 : 1
: 1
VCR1:AUTO : - : : 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : A : : MAIN
NEXT
Select a desired sub-menu with the 3 or 4
cursor buttons, and press the ENTER button to
enter. The display will change to the selected
sub-menu. You can lock the condition of setup
to each sub-menu with the 1 or 2 or cursor
buttons.
Note:
If you desire to adjust any sub-menu, you need to set
it to UNLOCKED.
4.
If you desire to exit from this menu system,
press the EXIT button, or move the cursor to
EXIT and press the ENTER button.
1.
2.
3.
4.
5.
6.
7.
INPUT SETUP
:UNLOCK
SPEAKER SETUP:UNLOCK
PREFERENCE
:UNLOCK
SURROUND
:UNLOCK
PL II MUSIC
:UNLOCK
CS II
:UNLOCK
7.1 CH. INPUT:UNLOCK
EXIT
4 SURROUND
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
EXIT
3 PREFERENCE
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------CD
:AUTO : 4 :
:
TAPE:AUTO : - :
:
CD-R:AUTO : 5 :
:
AUX2:AUTO : - :
:
MAIN
RETURN
STANDBY MODE
TV-AUTO
OSD INFO
BILINGUAL
VIDEO CONVERT
HDMI
DC TRIGGER
:
:
:
:
NORMAL
DISABLE
ENABLE
MAIN
: ENABLE
MAIN
EXIT
MAIN
EXIT
5 PL II MUSIC PARAMETER
PARAMETER
: DEFAULT
PANORAMA
: OFF
DEMENSION
:
3
CENTER WIDTH :
3
EXIT
3-1 VIDEO CONVERT
There are 7 items in the SETUP MAIN MENU.
3.
ENGLISH
SETUP
2-1 SPEAKERS SIZE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
2-2 SPEAKERS DISTANCE
FRONT L
: 10
FRONT R
: 10
CENTER
: 10
SURR.L
: 10
SURR.R
: 10
SUB W
: 10
SURR.B L : 10
SURR.B R : 10
MAIN
RETURN
ft
ft
ft
ft
ft
ft
ft
ft
NEXT
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
EXIT
2-3 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
MAIN
ON
ON
ON
ON
ON
6 CS II PARAMETER
MAIN RETURN
EXIT
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
MAIN RETURN
EXIT
CD
:
TAPE :
CD-R :
AUX2 :
TUNER:
7.1CH:
EXIT
TRUBASS
SRS DIALOG
MAIN
: 0
: 0
EXIT
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
19
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL
INPUT AND COMPONENT VIDEO INPUT)
6 digital inputs, 3 component video inputs and 2
HDMI inputs can be assigned to a desired source.
Use this menu to select the digital input jack to be
assigned to the input source.
1.
Select “INPUT SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
Notes:
• When the TUNER is fixed to the analog input, you
can not select any digital input.
• When a DTS-LD or DTS-CD is playing, this setup is
not available. This is to avoid noise being generated
from the analog input.
• If “DIG” is selected and a DVD, compact disc or
LD is fast-forwarded during playback, decoded
signals may produce a skipping sound. In such cases,
change the setting to DIGITAL.
2 SPEAKER SETUP
After you have installed the DN-A7100, connected all
the components, and determined the speaker layout,
it is now time to perform the settings in the Speaker
Setup menu for the optimum sound acoustics for
your environment and speaker layout.
Before you perform the following settings, it is
important that you first determine the following
characteristics:
2-1 SPEAKERS SIZE
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 3 : : DVD :AUTO : 1 : 1
: 1
VCR1:AUTO : - : : 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : A : : MAIN
NEXT
EXIT
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------CD
:AUTO : 4 :
:
TAPE:AUTO : - :
:
CD-R:AUTO : 5 :
:
AUX2:AUTO : - :
:
MAIN
RETURN
2-1 SPEAKERS SIZE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
EXIT
2.
To select the input source and MODE, press
the 3 or 4 cursor buttons.
3.
To select “DIG” “HDMI” or “COMP” for the input
jack, press the 1 or 2 cursor buttons.
Select “DIG” for input sources, for automatic
detection of the digital input signal condition.
If there is not a digital signal present, but there
is an analog signal present, the analog signal
will be played.
Select “DIG”, when only a digital signal will be
used. Select “ANA” for input sources for which
no digital input jacks are used.
20
When setting the speaker size in the SPEAKER
SIZE sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel you
are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting lower
than approx. 100 Hz will be output from the
subwoofer.
If the Subwoofer is set to “NONE” and the front
speakers are set to “LARGE,” then the sound will
be output from both the left and right speakers.
4.
To select the vdieo source, select “HDMI” or
“COMP” by pressing the 3 or 4 cursor buttons,
and press the 1 or 2 cursor buttons to select
the vdieo source to be assigned .
5.
After you complete this portion of the set up,
move the cursor to MAIN with the 3 or 4 cursor
buttons and press the ENTER button.
1.
Select “SPEAKER SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
2.
To select the each speaker, press the 3 or 4
cursor buttons.
3.
To select the setting of each speaker size,
press the 1 or 2 cursor buttons.
4.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
• If “NONE” is selected for the Subwoofer setting,
then this setting is fixed to “LARGE.”
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are
connected.
LARGE:
Select if the surround left and right speakers are
large.
SMALL:
Select if the surround left and right speakers are
small.
SURR. BACK
NONE:
Select if no surround back left and right speakers
are connected.
2CH:
Select if the surround back left and right speakers
are connected.
1CH:
Select if the one surround back speaker is
connected.
In this case, the audio signal is emitted form the
Surround back L output terminal.
Notes:
If “NONE” is selected for the Surround L/R setting,
then this setting is fixed to “NONE.”
Note:
If “NONE” is selected for the Surround L/R setting,
then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the cutoff
frequency for the small speakers used. Select one of
the crossover frequency levels according to the size
of the small speaker connected.
80Hz → 100Hz → 120Hz → 150Hz → 180Hz
Notes:
• If using small front speakers, set a slightly higher
frequency. If using large front speakers, set a slightly
lower frequency.
• If Pure-Direct mode, 7.1CH Input is in use, this
function does not take effect.
BASS MIX
• The bass mix setting is only valid when “LARGE”
is set for the front speakers and “YES” is set for the
subwoofer during stereo playback .
This setting has effect only during playback of
PCM or analog stereo sources.
• When “BOTH” is selected, the low frequencies will
be played through the main L&R, as well as the
sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but
depending on the size and shape of the room,
interference may result in a decrease of the actual
volume of the low frequency range.
• By selecting “MIX”, the low frequencies will play
through the main L&R ONLY.
Note:
LFE signals during playback of Dolby Digital or DTS,
will be played through the sub woofer.
2-2 SPEAKERS DISTANCE
Use this parameter to specify the distance of each
speaker’s position from the listening position. The
delay time is automatically calculated according to
these distances.
Begin by determining the ideal or most commonly
used seating position in the room.
This is important for the timing of the acoustics to
create the proper sound space that the DN-A7100
and today’s sound systems are able to produce.
Note:
For speakers that you have selected “NONE” the
Speaker Configuration sub-menu will not appear
here. (There are several useful books and special
DVD and LD’s available to guide you through proper
home theater configuration. If you are unsure, have
your DENON dealer perform the installation for you.
They are trained professionals familiar with even the
most sophisticated custom installations. DENON
recommends the WWW.CEDIA.ORG website for
further information about this).
2-2 SPEAKERS DISTANCE
FRONT L
: 10
FRONT R
: 10
CENTER
: 10
SURR.L
: 10
SURR.R
: 10
SUB W
: 10
SURR.B L : 10
SURR.B R : 10
MAIN
RETURN
1.
ft
ft
ft
ft
ft
ft
ft
ft
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
EXIT
To select each speaker , press the 3 or 4
cursor buttons.
2.
To set the distance for each speaker , press the
1 or 2 cursor buttons.
3.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
FRONT L:
Set the distance from the front left speaker to your
normal listening position.
CENTER:
Set the distance from the center speaker to your
normal listening position.
FRONT R:
Set the distance from the front right speaker to
your normal listening position.
SURR. L:
Set the distance from the surround left speaker to
your normal listening position.
SURR. R:
Set the distance from the surround right speaker
to your normal listening position.
SUB W:
Set the distance from the subwoofer to your
normal listening position.
SURR. B L:
Set the distance from the surround back left
speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right
speaker to your normal listening position.
Notes:
• Set the distance to each speaker in meters (m) or feet
(ft) as follows.
m: 0.3 - 9 m in 0.3 m steps
ft: 1 - 30 ft in 1 ft steps
• For the speakers that you have selected “NONE” the
Speaker Size menu will not appear.
• The setting for Surr.Back L and Surr.Back R appears
if you set for it to, two surround back speakers in the
Speaker Size menu.
• The setting of Surr.Back appears if it is set for one
surround back speaker in the Speaker Size menu.
2-3. SPEAKERS LEVEL SETTING WITH TEST TONE
Here you will set the volume for each speaker so that
they are all heard by the listener at the same level.
We recommend using a SPL (Sound Pressure Level)
meter, when available.
Note:
The speaker level settings are not available in 7.1
Channel Input mode, CS mode and Multi Channel
Stereo mode.
2-3 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
TEST MODE :
Selects “MANUAL” or “AUTO” for generating
the mode of the test tone with the 1 or 2 cursor
buttons.
If you select “AUTO” , the test tone will be cycled
through in a circular pattern which is Left → Center →
Right → Surround Right → Surround Back Right →
Surround Back Left → Surround Left → Subwoofer
→ Left → .. increments of 2 seconds
for each channel.
Using the 1 or 2 cursor buttons, adjust the volume
level of the noise from the speaker so that it is the
same level for all the speakers.
ENGLISH
SURR. BACK SIZE
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
If you select “MANUAL”, adjust the output level of
each speaker as listed below.
1.
When you move the cursor to FRONT L by
pressing the 4 cursor button, the DN-A7100 will
emit a pink noise from the front left speaker.
Remember the level of this noise and then
press the 4 cursor button.
(Note that this can be adjusted to any level
between -10 and +10 dB in 1 dB intervals
except the subwoofer setting. The subwoofer
can be adjusted to any level between -15 and
+10 dB in 1 dB intervals.)
The DN-A7100 will now emit the pink noise
from the center speaker.
2.
Using the 1 and 2 cursor buttons, adjust the
volume level of the noise from the center
speaker so that it is the same level as the front
left speaker.
3.
Press the 4 cursor button again. The DNA7100 will now emit the pink noise from the
front right speaker.
4.
Repeat steps 2 and 3 above for the front
right and other speakers until all speakers are
adjusted to the same volume level.
After you complete this portion of the set up, press
the ENTER button, the cursor will move to “MAIN”
and then press the ENTER button to go to SETUP
MAIN MENU.
Notes:
• Speakers that you selected “NONE” for in the
Speaker Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears
if you have set it for two surround back speakers in
the Speaker Size menu.
• The setting of Surr.Back appears if you have set it for
one surround back speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input
sources, you will need to use the 7.1CH-INPUT sub
menu. (See page 23).
21
ENGLISH
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable
or disable with the 1 or 2 cursor buttons. (Video
cable connection: Refer to page 15)
3 PREFERENCE
3 PREFERENCE
STANDBY MODE
TV-AUTO
OSD INFO
BILINGUAL
VIDEO CONVERT
HDMI
DC TRIGGER
MAIN
1.
2.
: ECONOMY
:
: ENABLE
: MAIN
: ENABLE
3-1 VIDEO CONVERT
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
ON
ON
ON
ON
ON
4 SURROUND
4 SURROUND
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
MAIN
EXIT
Select “PREFERENCE” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
To select a desired content, press the 3 or 4
cursor buttons.
STANDBY MODE:
When this function is set to “ECONOMY”, you can
reduce the power consumption when the unit is in
the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the
“ECONOMY” setting.
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with the 1 or 2 cursor buttons.
OSD Info:
Select the OSD information function to enable or
disable with the 1 or 2 cursor buttons.
If you select “ENABLE”, the DN-A7100 will display
the status of the feature (Volume up/down, input
select, etc..) on the TV monitor. But if you do not
desire this information, select “DISABLE”.
BILINGUAL:
In the Bilingual mode, Dolby Digital and DTS
output is set to either “MAIN” or “SUB”. Select
“BILINGUAL” with the 1 and 2 cursor buttons,
then select MAIN ↔ SUB ↔ MAIN+SUB with the
1 or 2 cursor buttons.
MAIN RETURN
EXIT
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
HDMI AUDIO:
This setting determines whether to playback audio
input to the HDMI jacks through the DN-A7100 or
output it through the receiver to a TV or projector.
ENABLE: The audio input to the HDMI jacks
can be played back by this receiver.
In such case, audio signals are not
output to the TV or projector.
THROUGH: The audio input to the HDMI jacks is
not output from the output terminals
of the DN-A7100. Audio data is
output directly to the TV or projector.
This setting is used to listen to audio
on a multi channel TV, etc.
DC TRIGGER:
Select “DC TRIG SETUP” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
MAIN RETURN
CD
:
TAPE :
CD-R :
AUX2 :
TUNER:
7.1CH:
EXIT
You can select MAIN ROOM, REMOTE or DISABLE
by pressing 1 or 2 cursor buttons.
22
Notes:
• REMOTE is available for the external control. The
RC-1065 cannot operate this function.
• To select desired input source , press 3 or 4 cursor
button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor
buttons and press the ENTER button.
EXIT
1.
Select “SURROUND” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select a desired content , press the 3 or 4
cursor buttons.
SURR.MODE:
Select the desired surround mode with the 1 or 2
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
film soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a film
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the 1 or 2 cursor
buttons.
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
6 CS II (CIRCLE SURROUND II) PARAMETER
This sub-menu is to adjust the speaker levels for 7.1channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
6 CS II PARAMETER
Pro Logic II-Music mode creates a rich and enveloping
surround ambience from stereo sources such as
CDs.
In this mode, DN-A7100 includes three controls to
fine-tune the soundfield as follows.
TRUBASS
SRS DIALOG
7 7.1 CH INPUT LEVEL
: 0
: 0
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
5 PL II MUSIC PARAMETER
MAIN
PARAMETER
MAIN
EXIT
: DEFAULT
1.
PANORAMAA
: OFF
DIMENSION
:
3
CENTER WIDTH :
3
EXIT
Select “PL II MUSIC” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the ENTER
button.
PARAMETER:
Select “DEFAULT” or “CUSTOM” with the 1 or 2
cursor buttons.
If you select “CUSTOM”, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
1 or 2 cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level
in 1 level intervals with the 1 or 2 cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the 1 or 2 cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the center
is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
Select “CS II” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the
ENTER button.
2.
To Select desired contents as below, press the
3 or 4 cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1
level interval with the 1 or 2 cursor buttons.
TRUBASS produced by the speakers are an octave
below the actual physical capabilities of the speakers
adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the 1 or 2 cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
ENGLISH
5 PL II (PRO LOGIC II)
MUSIC PARAMETER
1.
Select “7.1CH INPUT” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select “VIDEO IN”, press 3 or 4 cursor
button.
3.
Using the 1 or 2 cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
1 or 2 cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔
AUX1 ↔ V-OFF ↔ LAST ↔
Notes:
• When select LAST, the source is set previous source
before 7.1 CH INPUT function is activated.
• When select V-OFF, no signal is emitted from monitor
out terminal.
4.
To Select desired channel , press the 3 or 4
cursor buttons.
5.
Using the 1 or 2 cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to “MAIN” with the 3 or 4
cursor buttons and press the ENTER button.
Notes:
• These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH-SEL button of the remote controller.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
23
ENGLISH
SIMPLE SETUP
You can setup the speaker conditions quickly with
SIMPLE SETUP menu. In this menu, the number
of speakers and speaker delay time can be set.
These settings can be changed more detail in “2.
SPEAKER” setup menu.
Press the SETUP button on the unit to enter this
menu.
1.
2. 4. 3. 5.
The relation of the speakers number and
conectted speaker
CHANNEL
7.1 ch
7.0 ch
6.1 ch
6.0 ch
5.1 ch
5.0 ch
4.1 ch
4.0 ch
3.1 ch
3.0 ch
2.1 ch
2.0 ch
Front
L/R
(F)
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
Front Surround Surround
Back L/R
L/R
Center
(SB)
(S)
(C)
SMALL SMALL
2ch
SMALL SMALL
2ch
SMALL SMALL
1ch
SMALL SMALL
1ch
SMALL SMALL
NONE
SMALL SMALL
NONE
NONE SMALL
NONE
NONE SMALL
NONE
SMALL NONE
NONE
SMALL NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
Sub
woofer
(SW)
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
The relation of the room size and floor space
1.
Press the SETUP button on the unit to enter
the “SPEAKERS” menu.
2.
Press 1 or 2 cursor button to select the speaker
number.
3.
Press the 4 cursor button to enter the “ROOM”
menu.
4.
Press 1 or 2 cursor button to select the room
size.
5.
After finishing all setup, press the 4 cursor
button to exit the SIMPLE SETUP menu.
Note:
All Simple Setup menu is reset when the speaker
setting is changed with Speaker Setup menu.
SIMPLE SETUP
: ?
EXIT
24
Floor
space
Width
(W)
Depth
(D)
SMALL
10 m2
2.7 m
3.6 m
MEDIUM
16 m2
3.6 m
4.5 m
LARGE
24 m2
4.5 m
5.4 m
Imaging Distance
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
6 ft. (1.8 m)
5 ft. (1.5 m)
4 ft. (1.2 m)
5 ft. (1.5 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
9 ft. (2.7 m)
8 ft. (2.4 m)
7 ft. (2.1 m)
8 ft. (2.4 m)
8 ft. (2.4 m)
The relation of the room size and floor space is a
roughly standard.
1.SPEAKERS : ?
2.ROOM
SIZE
(PLAYBACK)
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
first select the input source on the DN-A7100.
Example : DVD
To select DVD, turn the INPUT SOURCE knob on
the front panel or simply press the DVD button on
the remote.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• As the input is changed, the DN-A7100 will
automatically switch to the digital input, surround
mode, attenuation, and night mode status which
were entered during the configuration process for
that source.
• When an audio source is selected, the last video
input used remains routed to the VCR1 Output
and Monitor Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the Monitor
Output jacks and will be viewable on a TV monitor
connected to the DN-A7100.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
VIDEO CONVERT
When this function is activated, the video or
S-video signal can be emitted from the video, Svideo or component video output terminal.
To activate this function, select VIDEO CONVERT in
PREFERENCE menu and set ON.
Notes:
• The component video signal is emitted only from
component video output terminal.
When the video equipment is connected by
component terminal, connect the monitor and DNA7100 by the component terminal.
• This function is unavailable for the REC out
terminal.
• This function is unavailable for the still picture, fast
forward and reverse playing of the video component.
• If, while attempting to use the video convert feature,
the DN-A7100 cannot synchronize with the display
device, “NO SIGNAL” appears on the monitor, or
noise is generated, this feature cannot be used. All of
these signs are caused by equipment incompatibility;
there is nothing wrong with the DN-A7100.
In such case, set VIDEO CONVERT in the
PREFERENCE menu to OFF. Also, connect the
video input signal to the display device via the
MONITOR OUT terminal under VIDEO and the
S-video input signal to the display device via the
MONITOR OUT terminal under S-VIDEO.
HDMI
Example:
ENGLISH
BASIC OPERATION
Monitor is connected with the component.
HDMI
VIDEO
component
VIDEO
S-VIDEO
component
Monitor is connected with the video or S-video.
VIDEO
or S-VIDEO
Monitor is connected with the video or component.
S-VIDEO
VIDEO
component
VIDEO
S-VIDEO
component
HDMI
Notes of OSD menu:
HDMI: OSD menu is not displayed.
VIDEO/S-VIDEO/component: VIDEO CONVERT
of HDMI is not possible, thus the OSD menu is not
displayed.
VIDEO
component
or S-VIDEO
The signal cannot be converted from the component
to the video or S-video.
Notes of OSD menu:
• The setup menu can be displayed through all video
out (COMPONENT, S-VIDEO, VIDEO).
• The setting informations (e.g. volume setting) are
displayed through all video out when the VIDEO
CONVERT function are set ON.
Note:
No setting information is displayed when the
signal is emitted from the COMPONENT IN to
COMPONENT OUT.
• The setting informations (e.g. volume setting) are
displayed through the S-VIDEO or VIDEO out
when the VIDEO CONVERT function are set
OFF. When the S-VIDEO and VIDEO outputs are
used simultaneously, the setting informations are
displayed through the S-VIDEO out only.
25
ENGLISH
SELECTING THE SURROUND MODE
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
NIGHT MODE
Example: AUTO SURROUND
To select the surround mode during playback, press
the SURROUND button on the front panel or the
SURROUND buttons on the remote.
ADJUSTING THE MAIN VOLUME
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote control unit)
To adjust the bass effect, press BASS + or BASS
– on the remote.
To adjust the treble effect, press TREBLE + or
TREBLE – on the remote.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
Adjust the volume to a comfortable level using the
VOLUME control knob on the front panel or VOL
+/– buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOL + button on the remote, to
decrease the volume, turn counterclockwise or press
VOL – button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 21, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
26
USING THE SLEEP TIMER
TEMPORARILY TURNING OFF
THE SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.
To program the DN-A7100 for automatic standby,
press the SLEEP button on the remote.
Each press of the button will increase the time before
shut down in the following sequence.
OFF
90
10
80
20
30
40
70
60
50
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.
Press the NIGHT button on the remote to turn on the
NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late
at night.
To turn off the Night mode, press the NIGHT button
again.
The DN-A7100 is equipped with many surround
modes. These are provided to reproduce a variety of
surround sound effects, according to the content of
the source to be played.
The available surround modes may be restricted
depending on the input signal and speaker setup.
AUTO
When this mode is selected, the receiver determines
whether the digital input signal is Dolby Digital, Dolby
Digital Surround EX, DTS, DTS-ES, DTS 96/24 or
PCM-audio.
Surround EX & DTS-ES will operate for multichannel
source that has a Dolby Digital Surround EX or DTSES auto trigger flag in the digital signal.
When a Dolby Digital or DTS signal is input, the
number of channels for which the corresponding
signal is encoded will be played.
Inputting a Dolby Digital two channel signal with
Dolby surround status automatically subjects that
signal to Pro Logic IIx movie processing before play.
PCM 96 kHz source material can be played in this
mode.
Notes:
• When you use this mode with certain DVD and CD
players, performing operations such as “Skip” or
“Stop” may momentarily interrupt the output.
• When the signal is not decoded, the mode is changed
to AUTO mode automatically. Refer to page 29 to
confirm the available decoding mode.
2 MODE
EX/ES
(Dolby Digital, Pro Logic IIx MOVIE, Pro Logic IIx
MUSIC, Pro Logic IIx GAME, Pro Logic)
This mode is used with source materials encoded in
Dolby Digital and Dolby Surround.
This mode provides 6.1 channel surround for DOLBY
DIGITAL EX, DTS-ES encoded source material such
as DVD.
This mode cannot be used when an analog input has
been selected.
DOLBY DIGITAL
This mode is enabled when playing source materials
encoded in Dolby Digital.
Playing multichannel encoded 6.1 or 7.1-channel
Dolby Digital sources provides five main audio
channels (left, center, right, surround left and surround
right) and Low Frequency Effect channel.
Dolby Digital EX decoding is not available in this
mode.
Dolby Digital EX
In a movie theater, film soundtracks that have been
encoded with Dolby Digital surround EX technology
are able to reproduce an extra channel which has
been added during the mixing of the program.
This channel, called Surround Back, places sounds
behind the listener in addition to the currently
available front left, front center, front right, surround
right, surround left and subwoofer channels.
This additional channel provides the opportunity
for more detailed imaging behind the listener and
brings more depth, spacious ambience and sound
localization than ever before.
Dolby Digital EX is not available in the system without
surround back speaker(s).
Dolby Pro Logic IIx brings the excitement of surround
sound to any stereo mix, while making existing
Dolby Surround mixes sound more like discrete 5.1
channels Surround sound.
Dolby Pro Logic IIx has 3 modes. Please see below.
Pro Logic IIx MOVIE
This mode provides 6.1 or 7.1 channel surround
sound from Dolby Surround encoded stereo movie
sound tracks.
Pro Logic IIx MUSIC
This mode provides 6.1 or 7.1 channel surround
sound from conventional stereo sources, analog or
digital, such as CD, Tape, FM, TV, Stereo VCR, etc.
Pro Logic IIx GAME
Game mode restores the impact low-frequency
surround effects by routing them to the system’s
subwoofer.
Pro Logic
This mode emulated original Dolby Pro Logic
decoding (3/1 surround) suit for Dolby Surround
encoded stereo movie soundtracks.
Notes:
• Pro Logic IIx mode will decode as Pro Logic II
mode when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 20)
• Pro Logic IIx mode is available for a 2ch input signal
which is encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
DTS-ES (Discrete 6.1, Matrix 6.1)
DTS-ES adds the surround back channel audio to
the DTS 5.1-channel format to improve the acoustic
positioning and makes acoustic image movement
more natural with the 6.1-channel reproduction.
This receiver incorporates a DTS-ES decoder, which
can handle DTS-ES Discrete-encoded and DTS-ES
Matrix-encoded program sources from DVD, etc..
DTS-ES Discrete 6.1 features digital discrete
recording of all channels including the surround back
channel(s) and higher quality of audio reproduction.
DTS-ES is not available in the system without a
surround back speaker.
dts MODE
(dts, Neo:6 Cinema, Neo:6 Music)
This mode is for DTS encoded source materials such
as LASER DISC, CD, and DVD. Neo:6 is for some 2
channel sources.
dts : This mode is enabled when playing source
materials encoded in dts multichannel.
Playing multichannel encoded 5.1-channel dts
sources provides five main audio channels (left,
center, right, surround left and surround right) and
Low Frequency Effect channel.
dts-ES decoding is not available in this mode.
The DTS mode cannot be used when an analog
input has been selected.
Neo:6 Cinema, Neo:6 Music
This mode decodes 2-channel signals into 6channel signals using high-accuracy digital matrix
technology.
The DTS NEO:6 decoder has near-discrete properties
in the frequency characteristics of the channels as
well as in channel separation.
According to the signals to be played back, DTS
NEO:6 uses either the NEO:6 CINEMA mode
optimized for movie playback or the NEO:6 MUSIC
mode optimized for music playback.
ENGLISH
SURROUND MODE
Notes:
• Neo:6 mode is available to 2ch input signals which
are encoded in Dolby Digital or PCM Analog
format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
MULTI CH. ST
This mode is used to create a wider, deeper and more
natural soundstage from two channel source material.
This is done by feeding the left channel signal to
both left front and left surround speaker and the right
channel signal to both right front and right surround
speaker. Additionally, the center channel reproduces
a mix of the right and left channel.
CIRCLE SURROUND II
(CSII-CINEMA, CSII-MUSIC, CSII-MONO)
Circle Surround is designed to enable multichannel
surround sound playback of non-encoded and
multichannel encoded material.
Backward compatibility provides listeners with up to
6.1 channels of surround performance from entire
collection of music and film, including broadcast,
videotape and stereo recorded music.
Depending on source material, you can select CSIICinema mode, CSII-Music mode or CSII-Mono
mode.
CSII Cinema mode
This mode is suited for playing back Circle Surroundencoded and non-encoded film and television
soundtracks. Cinema Mode enables 6.1-channel
surround playback of 2-channel sources such as
Video Cassettes, TV broadcasts, streaming media
and DVDs.
CSII Music mode
This mode is suited for playing back Circle
Surround-encoded and non-encoded music. Music
Mode decodes, music DVDs, radio and TV music
broadcasts and CDs into enveloping 6.1-channel
surround.
27
ENGLISH
CSII-Mono mode
This mode plays back monaural recordings from
any source, including CDs, DVDs and TV and radio
broadcasts in compelling 6.1-channel surround.
Notes:
• CS II mode is available for 2ch input signals which
are encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
VIRTUAL
This mode creates a virtualized surround sound
experience from a two-speaker (front L and R)
playback system playing any multichannel audio
source (such as found on DVDs and digital
broadcasts), including Dolby Digital, Dolby Pro Logic
or DTS.
STEREO
This mode bypasses all surround processing.
In stereo program sources, the left and right channels
play normally when PCM-audio or analog stereo is
input.
With Dolby Digital and DTS sources, the 5.1
multichannels are converted to two channel stereo.
96 kHz PCM source material can be played back in
stereo mode.
SOURCE DIRECT
In the Source Direct mode, the tone control circuit
and bass management configuration are bypassed
for full-range frequency response and the purist
audio reproduction.
Notes:
• Speaker size is set to Front L/R = LARGE, Center =
LARGE, Surround L/R = LARGE and Subwoofer
= YES automatically. Tone controls, equalizer and
additional processing are deactivated.
• When you use this mode with certain DVD and CD
players, performing operations such as skip or stop
may momentarily interrupt the output.
PURE DIRECT
The Pure Direct mode further reduces sources of
noise in addition to effect of the Source Direct mode,
by blocking output from the video jacks (VIDEO,
S-VIDEO, COMPONENT VIDEO and HDMI) and
turning the FL display off.
28
CAUTION
NOTE for DTS signal
* Connected DVD player, laserdisc player or CD
player needs to support DTS digital output. You
may not be able to play some DTS source signals
from certain CD players and LD players even if you
connect the player to the DN-A7100 digitally. This
is because the digital signal has been processed
(such as the output level, sampling frequency or
frequency response), and the DN-A7100 cannot
recognize the signal as DTS data.
* Depending on the player used, DTS play may
produce a short noise. This is not a malfunction.
* While signals from a DTS laserdisc or CD are
playing in another surround mode, you cannot
switch to digital input or from digital input to analog
input from the INPUT SETUP in the MAIN MENU
or by pressing the A/D button.
* The outputs for VCR OUT, TAPE OUT, and CD-R/
MD OUT output analog audio signals only. Do not
record from CDs or LDs that support DTS using
these outputs. If you do, the DTS-encoded signal
will be recorded as noise.
NOTE for Dolby Digital Surround EX signal
* When playing Dolby Digital Surround EX-encoded
software in 6.1 channels, it is required to set the
EX/ES mode.
* Note that some of Dolby Digital Surround
EX-encoded software does not contain the
identification signal. In this case, set the EX/ES
mode manually.
NOTE for 96kHz PCM audio
* AUTO, PURE-DIRECT, and STEREO modes
can be used when playing PCM signals with
a sampling frequency of 96 kHz (such as from
DVDVideo discs that contain 24 bit, 96 kHz audio).
If such signals are input during playback in one of
the other surround modes, output from DN-A7100
will be muted.
* Certain DVD player models inhibit digital output.
For details, refer to the player’s operation manual.
* Some DVD formatted discs feature copy protection.
When using such disc, 96 kHz PCM signal is not
output from the DVD player. For details, refer to
the player’s operation manual.
NOTE for HDCD signal
* HDCD is effective only through digital input.
* You may not be able to play some HDCD source
signals from certain CD players if you connect the
player to the DN-A7100 digitally. This is because
the digital signal has been processed (such as
the output level, sampling frequency or frequency
response) and the DN-A7100 cannot recognize
the signal as HDCD data.
Surround
Mode
AUTO
SOURCE DIRECT
PURE DIRECT
EX/ES
DOLBY
(PL IIx movie)
(PL IIx music)
(PL IIx game)
(Pro Logic)
DTS
(Neo:6 Cinema)
(Neo:6 Music)
CS II Cinema
CS II Music
CS II Mono
STEREO
Output Channel
Input Signal
Decoding
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D(2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM(Audio)
PCM 96kHz
HDCD
Analog
Dolby D Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby D Surr. EX
Dolby D (5.1ch)
DTS-ES
DTS(5.1ch)
Multi-PCM
AAC (5.1ch)
Dolby D Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
Multi Ch-PCM
PCM (Audio)
Analog
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital EX
DTS-ES
DTS-ES
Multi Ch-PCM + Dolby EX
AAC EX
Dolby Digital 5.1
Dolby Digital 5.1
Pro Logic IIx
Pro Logic IIx
Multi Ch-PCM + PLIIx
Pro Logic IIx
Pro Logic IIx
DTS 5.1
DTS 96/24
DTS 5.1
Neo:6
Neo:6
Neo:6
Neo:6
CS II
CS II
CS II
CS II
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
PCM (Stereo)
Stereo
L/R
C
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
-
Front information display
SL SBL
SR SBR SubW Signal format indicators
O
O
O 2 DIGITAL
O
O 2 DIGITAL
- 2 DIGITAL
O
O
- 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O dts 96/24
O
O dts
O
O PCM
O
O PCM
- PCM
- PCM
- PCM HDCD
- ANALOG
O
O
O 2 DIGITAL
O
O 2 DIGITAL
- 2 DIGITAL
O
O
- 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O dts 96/24
O
O dts
O
O PCM
O
O PCM
- PCM
- PCM
- PCM HDCD
- ANALOG
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL
O
O
O dts , ES
O
O
O dts
O
O
O PCM
O
O AAC
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL
O
O
- 2 DIGITAL
O
O
- 2 DIGITAL , 2 SURROUND
O
O
O PCM
O
O
- PCM
O
O
- ANALOG
O
O dts, ES
O
O dts 96/24
O
O dts
O
O
- PCM
O
O
- ANALOG
O
O
- 2 DIGITAL
O
O
- 2 DIGITAL , 2 SURROUND
O
O
O PCM
O
O
O ANALOG
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL , 2 SURROUND
O 2 DIGITAL
O 2 DIGITAL
- 2 DIGITAL
- 2DIGITAL , 2 SURROUND
O dts, ES
O dts 96/24
O dts
O PCM
- PCM
- PCM
- PCM HDCD
- ANALOG
Channel status
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R, S
L, R
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
-
Surround
Mode
Virtual
Multi Ch.
Stereo
Output Channel
Input Signal
Decoding
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS (5.1ch)
PCM (Audio)
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Audio)
Analog
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Dolby Digital EX
Dolby Digital 5.1
Multi Channel Stereo
Multi Channel Stereo
DTS-ES
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
Multi Channel Stereo
Multi Channel Stereo
L/R
C
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Notes:
• Dolby Digital (2 ch: Lt/Rt): signal with Dolby
Surround flag Speakers are full set.
• No sound outputs from the surround speaker, center
speaker and subwoofer if the DVD disc has no
surround data.
Front information display
SL SBL
SR SBR SubW Signal format indicators
- 2 DIGITAL
- 2 DIGITAL
- 2 DIGITAL
- 2 DIGITAL , 2 SURROUND
- dts, ES
- dts
- PCM
- ANALOG
O
O
O 2 DIGITAL
O
O 2 DIGITAL
O
O
- 2 DIGITAL
O
O
- 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O dts
O
O PCM
O
O PCM
O
O
- PCM
O
O
- ANALOG
Abbreviations
L/R :
C:
SL/SR :
SBL/SBR :
SubW :
ENGLISH
The relation between the selected surround mode and the input signal
The surround mode is selected with the surround mode selector on DN-A7100 or the remote control unit. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That
relationship is as follows;
Channel status
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
-
Front speakers
Center speaker
Surround speakers
Surround Back speakers
Sub woofer speaker
29
ENGLISH
OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
VIDEO ON/OFF
When no video signal is connected to the DN-A7100
or a DVD, etc., is connected directly to your TV,
the unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFF button.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the DN-A7100.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 22 : System Setup)
2.
Connect your TV TUNER (etc) to the TVVIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
DN-A7100.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, the DN-A7100
turns ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the DN-A7100 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the DN-A7100
is set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT and VCROUT.
This function is memorized for each individual input
source.
DISPLAY MODE
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the DN-A7100’s
output through a pair of headphones. Be certain that
the headphones have a standard 1/4” stereo phono
plug.
You can select the display mode for the front display
of the DN-A7100.
To select this mode, press the DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition
30
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the A/D button.
When this button is pressed, the input mode is
switched in the following sequence.
→ HDMI Auto → HDMI → Digital Auto → Digital
→ Analog → HDMI Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 20)
In normal operation, the audio or video source
selected for listening through the DN-A7100 is sent
to the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR OUT in the record mode.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS/VCR2
to video cassette recorder connected to the VCR
OUT jack.
To record the input source signal you are currently
watching or listening to
1.
2.
1.
1.
1.
Select the input source to record by turning the
INPUT SOURCE knob on the front panel or
simply press the input selector buttons on the
remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the TAPE OUT, CD-R/MD OUT, VCR
OUT outputs for recording.
3.
Start recording to the recording component as
desired.
1.
Switch the video output source to VCR1 by
simply pressing the input selector buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote.
3.
Now “CD” has been selected as the audio input
source and “VCR1” as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
HT-EQ (HOME THEATER EQUALIZER)
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in
the following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
1.
The DN-A7100 is equipped for future expansion
through the use of Multi channel Super Audio CD
multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back the pre-out jacks without passing through the
surround circuitry.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources.
1.
4.
2.
4.
Press the HT-EQ button on the unit.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2.
7.1 CH INPUT
ENGLISH
RECORDING AN ANALOG SOURCE
To cancel this function, press the HT-EQ button
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.
3.
1.
31
ENGLISH
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press 7.1 CH IN on the remote to switch the 7.1
channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
4.
Adjust the main volume with the VOLUME
knob or the VOL –/+ buttons on the remote.
To cancel the 7.1 CH. INPUT setting, press 7.1 CH
IN on the remote.
Notes:
• 7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
1. 2.
Frequency scan step for AM is selectable.
Default setup is 9 kHz step, if your country’s standard
is 10 kHz step, Press BAND button on the remote
more than 6 seconds. Scan step will change.
LIP.SYNC
Note:
The LIP.SYSNC feature turns OFF (0 ms) in the
PURE DIRECT mode. When the PURE DIRECT
mode is deactivated, the set value of the LIP.SYSNC
feature is automatically restored.
1. 2.
1.
2.
2.
(Using the DN-A7100)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
2.
Press the 3 or 4 cursor buttons on the front
panel to select the desired station.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
2.
Press the TUNING – / + on the remote to tune
in the desired station.
DIRECT FREQUENCY CALL
(Using the DN-A7100)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
2.
Press the 3 or 4 cursor buttons on the front
panel for more than 1 second to start the auto
tuning function.
3.
Automatic searching begins then stops when a
station is tuned in.
1.
3.
2.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
2.
Press the TUNING – / + for more than 1 second
on the remote.
3.
Automatic searching begins then stops when a
station is tuned in.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
32
1.
LISTENING TO THE TUNER
AUTO TUNING
Depending on the image device (TV, monitor,
projector, etc.) connected to the DN-A7100, a time
lag can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the DNA7100 to correct the time lag between the sound
and image. It can be operated with the “LIP.SYNC”
and 1 and 2 cursor buttons of the remote controller.
Set the remote controller to the AMP mode before
operating the LIP.SYNC feature. The initial setting is
OFF (0 ms).The time lag can be adjusted in 10 ms
steps up to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
MANUAL TUNING
(TUNER)
Note:
Preset memory for the tuner will clear by changing
this setup.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
BASIC OPERATION
1.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
2.
Press the F.DIRECT on the remote, display will
show “FREQ - - - -”.
3.
Input your desired station’s frequency with the
numeric buttons on the remote.
4.
The desired station will automatically be tuned.
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
2. 4.
3.
AUTO PRESET MEMORY
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The “ST” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators are not illuminated.
If the signal is weak, it may be difficult to tune into
the station in stereo. In such a case, press the
T-MODE button on the front panel or remote.
“AUTO” indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the “ST”
indicator is not illuminated.
To return to auto stereo mode, press the T-MODE
button or press T-MODE button on the remote again.
AUTO indicator is illuminated on the display.
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2.
5.
2.
1.
To select FM, press the BAND button on the
front panel.
2.
While pressing the MEMORY button, press the
2 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3.
4.
3.
1.
2.
1.
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
During this time, the following operations are
possible.
2.
Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
The band can be changed by the BAND button.
3.
Enter the desired preset number by pressing
the numeric buttons.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
Operation stops automatically when all 50
preset memory positions are filled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
(Using the DN-A7100)
1.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel
(Using the remote control unit)
1.
Press the PRESET – / + buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote.
PRESET SCAN
The station is now stored in the specified preset
memory location.
(Using the remote control unit)
Each time the tuner finds a station, scanning
will pause and the station will be played for five
seconds.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
1.
(Using the DN-A7100)
4.
1. 3.
RECALLING A PRESET STATION
MANUAL PRESET MEMORY
PRESET MEMORY
ENGLISH
(FM) TUNING MODE (AUTO STEREO OR MONO)
3.
3.
1.
3.
(Using the remote control unit)
1.
Press the P-SCAN on the remote.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled first.
2.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3.
You can fast forward the preset stations by
pressing the PRESET –/+ continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CL button or P-SCAN on the remote.
33
ENGLISH
CLEARING STORED PRESET STATIONS
SORTING PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
2.
3.
2. 5. 6.
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press and hold the MEMORY
and the 4 cursor buttons.
“PRESET SORT” will appear on the display and
sorting will be done.
4.
After selecting the first character to be entered,
press the MEMORY or ENTER buttons, press
the MEMO button on the remote.
The entry in this column is fixed and the next
column starts to flash. Fill the next column the
same way.
5.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press PRESET
– / + buttons on the remote.
Note:
Unused columns should be filled by entering blanks.
6.
1.
Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote.
3.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or press the CL button
on the remote.
4.
“xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
1.
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote for
more than 3 seconds.
3.
The left most column of the station name
indicator flashes, indicating the character entry
ready status.
4.
When you press the 3 or 4 cursor buttons on
the front panel or the TUNING – / + buttons on
the remote, alphabetic and numeric characters
will be displayed in the following order:
2. 5. 6.
5.
4.
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
34
5.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
3.
2.
NAME INPUT OF THE PRESET STATION.
To save the name, press the MEMORY button
on the front panel or remote for more than 2
seconds.
Ten keypad
1
2
3
4
5
6
7
8
9
0
Press, press again, press again, etc.
A→B→C→1→A
D→E→F→2→D
G→H→I→3→G
J→K→L→4→J
M→N→O→5→M
P→Q→R→6→P
S→T→U→7→S
V→W→X→8→V
Y → Z → space → 9 → Y
–→+→/→0
Now in use in many countries, RDS (Radio Data
System) is a description of the station’s programming
hidden space in the FM signal.
Your new receiver is equipped with RDS to assist
in the selection of FM stations using station and
network names, rather than broadcast frequencies.
Additional RDS functions include the ability to search
for programme types.
RADIO TEXT
Some RDS stations broadcast RADIO TEXT, which is
additional information on the station and programme
being broadcast.
RADIO TEXT information appears as ‘running’ text
in the display. RADIO TEXT is transmitted character
by the radio station. As a result of that it may take
some time until the entire text has been completely
received.
RDS DISPLAY
PTY AUTO SEARCH
When a receiver is tuned to an FM station that is
transmitting RDS data, the Front Panel Information
Display will automatically show the station name or
RADIO TEXT in place of the typical display of the
station’s broadcast frequency.
To change the display, press the T-DISP button on
the remote.
Your receiver is equipped to automatically search for
stations transmitting any of 29 different programme
types. To search for a PTY, follow these procedures:
2.
2.
2.
PS (Program Service Name)
RT (RADIO TEXT)
3.
Once the desired PTY group or type has
been selected, press the PTY button while
the display blink (approx. 5 seconds). The
PTY Auto search will start, and the tuner will
pause at each station broadcasting RDS PTY
information corresponding to the selected
choice.
4.
To advance to the next RDS station with the
desired PTY, press the PTY button again within
5 seconds.
The RDS system categorizes programmes according
to their genre into different programme type (PTY)
groups. To display the programme type information
of the current station, press the PTY button in the
TUNER MODE on the remote.
1.
3.
4.
Frequency
1.
Press the PTY button in the TUNER MODE on
the remote controller. The current station’s PTY
will be displayed, or the currently selected PTY
group will be displayed in blinking if no station
or RDS data is present.
2.
To change to a new PTY type, press the 3 or 4
cursor button on the front panel or numeric or
PRESET – / + buttons on the remote until the
desired PTY is shown in the display.
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
DISPLAY
POP
ROCK
MOR
LIGHT
CLASSIC
NEWS
AFFAIR
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
OTHERS
OTHER
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
HOBBIES
JAZZ
COUNTRY
NATION
OLDIES
FOLK
DOCUMENT
ENGLISH
PROGRAMME TYPE (PTY) DISPLAY
RDS OPERATION
PROGRAMME TYPE
Pop Music
Rock Music
M. O. R. Music
Light classical
Serious classical
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Other Music
Weather
Finance
Children’s programmes
Social Affairs
Religion
Phone In
Travel
Hobbies
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
35
ENGLISH
TROUBLESHOOTING
SYMPTOM
Can not select EX/ES mode.
In case of trouble, check the following before calling for service:
1.
Are the connections made properly ?
2.
Are you operating the unit properly following the user’s guide ?
3.
Are the power amplifiers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest DENON
authorized dealer or the DENON Service Center in your country.
SYMPTOM
CAUSE
REMEDY
DN-A7100 cannot be turned The power plug is not connected.
up.
Connect the power plug to the outlet.
No sound and picture are output Mute is on.
even when power is on.
The input cable is not connected correctly.
Cancel mute using the remote control unit.
See the connection diagram and connect the cables
correctly.
The master volume control is turned all Adjust the master volume.
the way down.
REMEDY
Surround center= NONE has been Make the correct setting.
selected in SPEAKERS SIZE SETUP
Input signal is incompatible.
Use 5.1channel source.
Can not select Pro Logic IIx
mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select Neo:6 mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select CSII mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
No output to Sub Woofer Out.
Sub-woofer = NONE has been selected in Select Sub-woofer = YES.
SETUP mode.
Noise is produced during DTSencoded CD or laser disc play.
Analog has been selected for input.
Be sure to perform digital connection, select digital
input, then play.
A specific channel does not
produce output.
Nothing recorded on source.
Check the encoded channel on the source side.
FM or AM reception fails.
Antenna connection is incomplete.
Correctly connect the indoor FM and AM antennas to
FM and AM antenna outlets.
The SOURCE position is wrong.
Select correct position.
Noise is heard during AM
reception.
Reception is affected by other electrical Try changing location where the AM indoor antenna
fields.
is set up.
Incorrect Audio or Video for
selected source.
Input cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Noise is heard during FM
reception.
The radio waves from the broadcasting Install an FM outdoor antenna.
station are weak.
Incorrect Audio from a channel.
Speaker cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Cannot get programmed station Preset data has been erased.
when the PRESET button is
pressed.
Disconnecting power plug for long periods of time will
erase preset data. If that happens, input the preset
data again.
Control with the remote control
unit fails.
Replace all the batteries with new ones.
No Audio output from the center The center speaker cable connection is Connect the cable correctly.
channel speaker.
incomplete.
STEREO has been selected for Surround When STEREO is selected for Surround mode, no
mode.
sound will be output from the center speaker. Set
another Surround mode.
Center = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround speakers.
The surround speaker cable connection Connect the cable correctly.
is incomplete.
STEREO has been selected for Surround When STEREO has been selected for Surround
mode.
mode, no sound will be output from the surround
speaker. Set another Surround mode.
Surround = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround back speakers.
The surround back speaker cable Connect the cable correctly.
connection is incomplete.
Surround mode is not EX/ES mode.
Set surround mode EX/ES.
Surround back = NONE has been selected Make the correct setting.
in SPEAKERS SIZE SETUP
36
CAUSE
Batteries are consumed.
Remote controller’s function-key setting Select different position from which equipment will
is wrong.
be controlled.
The distance between this DN-A7100 and Move closer to this DN-A7100.
the remote commander is too far.
Something is blocking DN-A7100 and the Remove offending object.
remote commander.
Note:
After “PROTECT” appears on the unit’s display, the standby indicator may start flashing. If it does, there is a problem
in the unit or the connection. If this problem reoccurs even when power is activated from the remote control unit,
call for servicing.
ENGLISH
DETAILED DESCRIPTION
RS-232C CONTROL SPECIFICATION
The interface specification between the product and a Host controller is described below.
GLOBAL DESCRIPTION
CONNECTION FORMAT
OVERVIEW
A Host controller can control or watch out the product as a Slave very easily via the communication cable.
Physical connection
Host (Controller)
Slave (the product)
BLOCK DIAGRAM
RS232C cable (straight)
HOST
(Controller)
SLAVE
(The product)
Connector
D-SUB (9pin, male)
* The product connector is using D-SUB 9pin male.
* RS232C cable must use D-SUB 9pin female to connect the products.
INTERFACE CONNECTION SPECIFICATION OF THE PRODUCT
Processor Interface
UART
-
Signal name
N.C.
TxD (output)
RxD (input)
N.C.
GND
N.C.
N.C.
N.C.
N.C.
Connection device
RS232C Level shift driver
GND
-
TxD
RxD
RxD
TxD
GND
GND
(Serial setting <RS232C basic>)
Baud Rate
: 9600bps
Data Bits
: 8bit
Parity
: None
Stop bit
: 1bit
Handshaking : None
• Data transmission sequence from Host to Slave
D-Sub Pin
1
2
3
4
5
6
7
8
9
Connecter
RS232C
D-SUB
(9pin,male)
Host (Controller)
TxD
1 2 3 4 5
RxD
6 7 8 9
Slave (The product)
/
,
RxD
TxD
1. Host starts a data transmission from TxD.
2. Host performs the data transmission of the number of required bytes, and ends a transmission.
• Data transmission sequence from Slave to Host
Host (Controller)
TxD
RxD
Slave (The product)
/
,
RxD
TxD
1. Slave starts a data transmission from TxD.
2. Slave performs the data transmission of the number of required bytes, and ends a transmission.
37
ENGLISH
TRANSMISSION DATA FORMAT
THE TRANSACTION SEQUENCES AND THE REGULATIONS
Transmission data format from Host to Slave
The transaction sequences
There are two kinds of transmission data form from Host shown below.
The transactions have three kinds of sequence.
* A transaction is a Command from Host then Slave will be an answer by Status answer, ACK or NAK.
* A transaction is a Status request from Host then Slave will be an answer by Status answer or NAK.
* A transaction is Auto status feedback from Slave when a Slave’s status changed. (If the auto status feedback
is enabled.)
• Form1: Command
Command is a data that requests some status change.
Start character
: ‘@’
COMMAND
: see “Command list”
End character (CR) : 0Dh
start
‘@’
command
“xxx:”+“...”
end
0Dh
• Form2: Status request
Status request is a data that requests a answer of some status.
Start character
: ‘@’
Request status
: see “Status request list”
Request character : ‘?’
End character (CR) : 0Dh
start
‘@’
request status
“xxx:?”+“...”
end
0Dh
Transmission data format from Slave to Host
There are two kinds of transmission data form from Slave shown below.
The transaction regulations
The transactions have some kinds of regulation.
* An answer (ACK, NAK or Status answer) transmittion by Slave has to finish within 500ms when got a
Command or a Status request from Host.
* Host must not transmit an another Command or Status request until “it receives a answer by a previous
Command or Status request” or “it passes a term of waitinng time from a finishing of previous transmission
of a Command or a Status request “.
* Slave has to finish a transaction under 500ms when it sends Auto status feedback data.
Specification of Auto status feedback
There are some specific regulations about Auto status feedback.
* The product status has segmented into four layers of 1, 2, 3 and 4.
* The status of layer 1 are assigned most kindly status to Host. (The statuses of layer 2 are assigned kindly
status, the statuses of layer 3 are not so need status to Host and the statuses of layer 4 are probably no
wished statuses.)
* Each layer status can control transmit enable or disable by Host command. (The product default would be
all disables.)
* Slave sends auto status feedback by itself when the status is changed and if the status feedback is
enabled.
* The product defined and segmentationed layers are takeing in status list.
• Form1: ACK/NAK
ACK is a reply data from Slave when Slave got an acceptable command data from Host.
(ACK is sent to Host when Slave has no related status by the Command.)
Start character : ‘@’, ACK : 06h, End character (CR) : 0Dh
start
‘@’
ACK
06h
Example of the transactions
<Host>
CR
0Dh
Command
TxD
NAK is a reply data from Slave when Slave got an incorrect Command data, Status request data or some
other data from Host.
Start character : ‘@’, NAK : 15h, End character (CR) : 0Dh
start
‘@’
NAK
15h
38
max. 0.5 sec
Status answer
RxD
end
0Dh
RxD
TxD
a transaction
Example of the transactions
Status answers are reply data when Slave got an acceptable Request status or Command data from Host.
Auto status feedbacks are send to Host data when a Slave’s status is changed.
Start character
: ‘@’
Answer character : see “Status list”
End character (CR) : 0Dh
status
“xxx:”+“...”
max. 0.5 sec
Status answer,
ACK or NAK
a transaction
CR
0Dh
• Form2: Status answer and Auto status feedback
start
‘@’
<Slave>
Status
request
RECOMMENDATIONS OF COMMAND, STATUS AND LAYER DEFINITION
• Example of successful handshaking
HOST
Command
SLAVE
Command
acceptable
Related
Status answer
or
ACK
Request
acceptable
Status request
- All Commands, Statuses and Layers will be defined other specific document.
- [MANDATORY] The product MUST have Commands and the Statuses same as a remote controller buttons
(IR controller) of the product.
- All commands are required working by discreate as ON/OFF commands. (It means that do not support
TOGGLE command only.)
- All Commands and Statuses are defined same character size except ACK/NAK on the product.(Recommended
character length : 3~6 characters)
- It permits attaching 0x0A character to reply characters from the product. In this case, must suppose that the
object is followed altogether.
- Recommend to supports numbers or values direct setting command, if it has variable numbers or values.
ENGLISH
Examples of the handshaking flowchart
Status answer
Changed
some status!
Auto status
feedback
The product can reply ACK instead of related status, if the product can not send the related status
immediatly.
• Examples of handshaking error
HOST
Command
SLAVE
Command
incorrect
NAK
Status request
Request
incorrect
NAK
39
ENGLISH
Display and Menu contents
RECOMMENDATIONS OF COMMAND, STATUS AND LAYER
Command
This section is told how to define “Command”,”Status”and “Layer” of this product.
SLEEP
Normal Command list
Main function contents
POWER
AUDIO ATT
AUDIO MUTE
VIDEO MUTE
VOLUME
TONE BASS
TONE TREBLE
SOURCE Select
7.1 Channel Input
40
Command
TOGGLE
OFF
ON
TOGGLE
OFF
ON
TOGGLE
OFF
ON
TOGGLE
OFF
ON
VALUE
Reply from Slave
“PWR:0”
“PWR:1”
“PWR:2”
“ATT:0”
“ATT:1”
“ATT:2”
“AMT:0”
“AMT:1”
“AMT:2”
“VMT:0”
“VMT:1”
“VMT:2”
“VOL:0xxx”
UP
“VOL:1”
DOWN
VALUE
UP
DOWN
VALUE
UP
DOWN
TV
DVD
VCR1
DSS/VCR2
AUX1
AUX2
CD
CD-R
TAPE
TUNER
FM
AM
TOGGLE
OFF
ON
“VOL:2”
“TOB:0xxx”
“TOB:1”
“TOB:2”
“TOT:0xxx”
“TOT:1”
“TOT:2”
“SRC:1”
“SRC:2”
“SRC:3”
“SRC:5”
“SRC:9”
“SRC:A”
“SRC:C”
“SRC:D”
“SRC:E”
“SRC:F”
“SRC:G”
“SRC:H”
“71C:0”
“71C:1”
“71C:2”
MENU
“PWR:1”,
“PWR:2”
“ATT:0”(None),
“ATT:1”(OFF),
“ATT:2”(ON)
CURSOR
“AMT:1”,
“AMT:2”
VALUE
OFF
TOGGLE
OFF(EXIT)
ON
ENTER
UP
DOWN
LEFT
RIGHT
Command
TRG.1 OFF
“VMT:1”,
“VMT:2”
DC TRG.
TRG.1 ON
“VOL:xxx”
xxx = vol. value as +18 ~-99,
0db = “VOL: 00”,
-∞ = “VOL:-ZZ”
Simple Setup
“TOB:xxx”
xxx = vol. value as +6 ~-6
“TOT:xxx”
xxx = vol. value as +6 ~-6
“SRC:va”, (v ,a= ‘0’ – ‘I’)
(v = video, a = audio.)
v=0(V-OFF)
a=N(7.1CH)
“71C:1”(OFF),
“71C:2”(ON)
Reply from Slave
“SLP:0xx”
(xx=00~99)
“SLP:1”
“MNU:0”
“MNU:1”
“MNU:2”
“MNU:3”
“CUR:1”
“CUR:2”
“CUR:3”
“CUR:4”
CURSOR
(same as Menu Cursor )
Command
TOGGLE
OFF(EXIT)
ON
ENTER
UP
DOWN
LEFT
RIGHT
“SPL:xx”
“SPL:00”
“MNU:1”(non-Menu mode),
“MNU:2”(on Menu mode)
ACK
Reply from Slave
“DCT:11”
(DC TRG. 1 OFF)
“DCT:12”
(DC TRG. 1 ON)
“DCT:a”
(a=1:OFF,2:ON),a=TRG.1
Reply from Slave
“SSU:0”
“SSU:1”
“SSU:2”
“SSU:3”
“CUR:1”
“CUR:2”
“CUR:3”
“CUR:4”
“SSU:1”(non-Setup mode),
“SSU:2”(on Setupmode)
ACK
Surr. Mode
Tuner contents
Command
AUTO
STEREO
DOLBY
PL2xMOVIE
PL2 MOVIE
PL2xMUSIC
PL2 MUSIC
PL2xGAME
PL2 GAME
Dolby PROLOGIC
EX/ES
VIRTUAL 6.1
DTS ES
NEO6 CINEMA
NEO6 MUSIC
Multi Ch. STEREO
CSII CINEMA
CSII MUSIC
CSII MONO
VIRTUAL
DTS
DD+ PL2x MOVIE
DD+ PL2x MUSIC
SOURCE DIRECT
PURE DIRECT
UP
DOWN
Reply from Slave
“SUR:00”
“SUR:01”
“SUR:02”
“SUR:03”
“SUR:04”
“SUR:05”
“SUR:06”
“SUR:07”
“SUR:08”
“SUR:09”
“SUR:0A”
“SUR:0B”
“SUR:0E”
“SUR:0F”
“SUR:0G”
“SUR:0H”
“SUR:0I”
“SUR:0J”
“SUR:0K”
“SUR:0L”
“SUR:0M”
“SUR:0O”
“SUR:0P”
“SUR:0T”
“SUR:0U”
“SUR:1”
“SUR:2”
Command
VALUE
Tuner Frequency
Tuner Preset
Tuner mode
“SUR:x“
(x = ‘0’ ~’Z’)
Tuner RDS
Tuner MEMO
CLEAR
Tuner Numeric keys
UP
DOWN
Auto-UP
Auto-DOWN
VALUE
UP
DOWN
P-Scan start
P-Scan stop
TOGGLE
OFF(MONO)
ON(AUTO)
DISP
PTY
Key0,
Key1,
Key2,
Key3,
Key4,
Key5,
Key6,
Key7,
Key8,
Key9
Reply from Slave
“TFQ:0xxxxx”
(xxxxx = freq.)
“TFQ:1”
“TFQ:2”
“TFQ:3”
“TFQ:4”
“TPR:0ww”
“TPR:1”
“TPR:2”
“TPR:3”
“TPR:4”
“TMD:0”
“TMD:1”
“TMD:2”
“RDS:3”
“RDS:4”
“MEM:0”
“CLR:0”
“NUM:0” ,
“NUM:1” ,
“NUM:2” ,
“NUM:3” ,
“NUM:4” ,
“NUM:5” ,
“NUM:6” ,
“NUM:7” ,
“NUM:8” ,
“NUM:9”
“TFQ:xxxxx”
(xxxxx = Frequency)
if (xxxxx < 02000) band=AM;
else band=FM;
(ex.“08750” = FM87.50MHz)
ENGLISH
Surround contents
“TPR:ww”
(ww = current preset nr.)
(ww = 01 ~ ??)
“TMD:0”( - ),
“TMD:1” (MONO),
“TMD:2” (AUTO)
ACK
ACK
ACK
ACK
Specific Commands
Test Tone
(Force start/stop Test
Tone with Auto mode)
Night Mode
Command
TOGGLE
OFF
ON
NEXT
PREV
TOGGLE
OFF
ON
Reply from Slave
“TTO:0”
“TTO:1”
“TTO:2”
“TTO:3”
“TTO:4”
“NGT:0”
“NGT:1”
“NGT:2”
Command
VALUE
Lip Sync.
UP
DOWN
“TTO:1xy” (OFF),
“TTO:2xy” (ON, x= auto(0)/
manual(1), y= ch.)
“NGT:1”(OFF),
“NGT:2”(ON)
Auto status feedback
Command from Host
“AST:x” (x = ‘0’ ~ ’F’)
(The product default is all auto
status feedback disabled.)
bit 3 : Layer 4 ( 1 = Enable, 0 = Disable)
bit 2 : Layer 3 ( 1 = Enable, 0 = Disable)
bit 1 : Layer 2 ( 1 = Enable, 0 = Disable)
bit 0 : Layer 1 ( 1 = Enable, 0 = Disable)
Reply from Slave
same as
command define
Reply from Slave
“LIP:0xxx” (xxx = value)
xxx = 000 (OFF),
xxx = 010,020,...190,200
(ms)
“LIP:1”
“LIP:2”
“LIP:xxx”
(xxx = Lip Sync. value)
xxx = 000 (OFF),
xxx = 010,020,...190.200 ms
41
ENGLISH
STATUS REQUEST AND STATUS ANSWER LIST
Status request
Normal Status request and Status (answer and feedback) list
Status request
POWER
“PWR:?”
AUDIO ATT
“ATT:?”
AUDIO MUTE
“AMT:?”
VIDEO MUTE
“VMT:?”
VOLUME
TONE BASS
TONE TREBLE
“VOL:?”
“TOB:?”
“TOT:?”
SOURCE Select
“SRC:?”
Multi Channel
“71C:?”
Status answer and feedback
OFF
“PWR:1”
ON
“PWR:2”
OFF
“ATT:1”
ON
“ATT:2”
OFF
“AMT:1”
ON
“AMT:2”
OFF
“VMT:1”
ON
“VMT:2”
Volume value = xxx
“VOL:xxx”
Bass value = xxx
“TOB:xxx”
Treble value = xxx
“TOT:xxx”
Video+Audio source
(v ,a= ‘0’ – ‘F’)
“SRC:va”
(v = video, a = audio.)
OFF
“71C:1”
ON
“71C:2”
Lip Sync.
“LIP:?”
Status answer and feedback
Lip Sync. : xxx = 000 (OFF)
“LIP:xxx”
xxx = 010 ~ 200 (ms)
Status request
Night Mode
Status answer and feedback
OFF
“NGT:1”
ON
“NGT:2”
“NGT:?”
Status request
Tuner Frequency
“TFQ:?”
Tuner Preset
“TPR:?”
Tuner Mode
“TMD:?”
Status answer and feedback
xxxxx = frequency
if (xxxxx < 02000) band = AM;
“TFQ:xxxxx”
else band = FM;
xx = preset number (01 ~ ??)
“TPR:xx”
- (None)
“TMD:0”
OFF (MONO)
“TMD:1”
ON (AUTO)
“TMD:2”
Layer of the statuses
Status
Status request
SLEEP
“SLP:?”
MENU
“MNU:?”
Status request
Simple Setup
“SSU:?”
Status request
Digital Signal Format
42
“SIG:?”
Status answer and feedback
Sleep time (xx = 00 ~ 99)
“SLP:xx”
OFF
“MNU:1”
ON
“MNU:2”
Status answer and feedback
OFF
“SSU:1”
ON
“SSU:2”
Status answer and feedback
x=
‘0’ : No detect
‘1’ : D DIGITAL AC-3
‘2’ : D DIGITAL SURROUND
‘3’ : D DIGITAL SURR. EX
‘4’ : DTS
‘5’ : DTS ES DISCREATE
‘6’ : DTS ES MATRIX
“SIG:x”
‘7’ : AAC
x = signal
‘8’ : MPEG
‘9’ : MLP
‘A’ : PCM
‘B’ : HDCD
‘C’ : DSD
‘D’ : reserved
‘E’ : reserved
‘F’ : OTHER
POWER
AUDIO ATT
AUDIO MUTE
VIDEO MUTE
VOLUME
TONE BASS
TONE TREBLE
SOURCE Select
Multi Channel
SLEEP
MENU
Simple Setup
“PWR:”
“ATT:”
“AMT:”
“VMT:”
“VOL:”
“TOB:”
“TOT:”
“SRC:”
“71C:”
“SLP:”
“MNU:”
“SSU:”
Status
Surr. Mode
Test Tone
Night Mode
Signal Format
Lip Sync.
“SUR:”
“TTO:”
“NGT:”
“SIG:?”
“LIP:?”
Status
Tuner Frequency
Tuner Preset
Tuner Mode
“TFQ:”
“TPR:”
“TMD:”
Layer
1
3
1
1
1
1
1
1
1
2
4
4
Layer
2
1
3
4
4
Layer
3
2
2
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, the DNA7100 is equipped with a backup function
to prevent memory data such as the preset
memory from being erased.
HOW TO RESET THE UNIT
Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
To turn on the DN-A7100, press and hold the
CLEAR and KEY-LOCK buttons simultaneously for
3 seconds or more.
Remember that the procedure will reset the settings
of the SOURCE, Surround mode, delay time, TUNER
PRESET etc., to their initial settings.
Frequency Range ................................ 87.5 – 108.0 MHz
Usable Sensitivity ............................IHF 1.8 µV/16.4 dBf
Signal to Noise Ratio ................... Mono/Stereo 75/70 dB
Distortion......................................Mono/Stereo 0.2/0.3 %
Stereo Separation .........................................1 kHz 45 dB
Alternate Channel Selectivity .................± 300 kHz 60 dB
Image Rejection .........................................98 MHz 70 dB
Tuner Output Level ........... 1 kHz, ± 75 kHz Dev 800 mV
AM TUNER SECTION
Frequency Range ................................... 531 – 1602 kHz
Signal to Noise Ratio .............................................. 50 dB
Usable Sensitivity .................................... Loop 400mV/m
Distortion...................................400Hz, 30 % Mod. 0.5 %
Selectivity.................................................± 20 kHz 70 dB
AUDIO SECTION
Input Sensitivity/Impedance (volume at 0dB)
(RCA connectors) .............................. 220 mV/ 20 kohms
(XLR connectors)
(+4dBu) ...................................... 440 mV/ 20 kohms
(-10dBV)......................................110 mV/ 20 kohms
Output Level (volume at 0dB)
(+4dBu) ........................................... 300 mVrms typ.
(-10dBV)............................................ 75 mVrms typ.
Signal to Noise Ratio(Analog Input / Pure Direct)... 98 dB
Frequency Response
(Analog Input / Pure Direct) ....... 10 Hz – 90 kHz (± 3 dB)
THD ...................................................................... 0.03 %
Cross Talk ............................................... 80 dB (at 1kHz)
VIDEO
Television Format............................................ NTSC/PAL
Input Level/Impedance ........................... 1 Vp-p/75 ohms
Output Level/Impedance......................... 1 Vp-p/75 ohms
Video Frequency Response ........5 Hz to 8 MHz (– 1 dB)
Video Frequency (Component)...5 Hz to 80 MHz (– 1 dB)
S/N ........................................................................ 60 dB
482.6 mm (19 ins.)
ENGLISH
140.8 mm
(5-1/2 ins.)
re-attempt to operate the equipment
11 mm
(7/16 ins.)
-
FM TUNER SECTION
324.85 mm
(12-3/4 ins.)
353.85 mm
(13-7/8 ins.)
after waiting at least three minutes, reconnect
the plug to the AC line supply
18 mm
(3/4 ins.)
disconnect the plug from the AC line supply
-
DIMENSIONS
132.6 mm
(5-1/4 ins.)
-
TECHNICAL
SPECIFICATIONS
8.2 mm
(5/16 ins.)
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
GENERAL
Power Requirement ................................AC 230 V 50 Hz
Power Consumption ................................................ 40 W
Weight ................................................................. 7.66 Kg
ACCESSORIES
Remote Control Unit RC-1065 ....................................... 1
AAA-size batteries ........................................................ 2
FM Antenna ................................................................... 1
AM Loop Antenna .......................................................... 1
AC Power Cord ............................................................. 1
Service Station List ........................................................ 1
User guide ..................................................................... 1
Specifications subject to change without prior notice.
43
D&M Holdings Inc.
PROFESSIONAL BUSINESS COMPANY
TOKYO, JAPAN
http://www.dm-pro.jp
12/2006
Printed in China
00D5114595008
ecmf-d