Converters.TV | 702 | Specifications | Converters.TV 702 Specifications

AUDIO/VIDEO CONTROL RECEIVER
RX-D702B
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
INSTRUCTIONS
Model No.
Serial No.
LVT1437-007A
[J]
cover_RX-D702B[J]_f.p65
3
05.8.25, 1:20 PM
Warnings, Cautions, and Others
Mises en garde, précautions et indications diverses
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution––
STANDBY/ON button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON button in any position does not disconnect the
mains line. The power can be remote controlled.
Attention—Touche
STANDBY/ON!
Déconnectez la fiche d’alimentation secteur pour couper
STANDBY/ON,
l’alimentation complètement. La touche
dans n’importe quelle position, ne déconnecte pas le système
du secteur. L’alimentation ne peut pas être télécommandé.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
CAUTION
Changes or modifications not approved by JVC could void the
user’s authority to operate the equipment.
For U.S.A
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For U.S.A
Declaration of Conformity:
Trade Name:
JVC
Model Number:
RX-D702B
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
JVC Americas Corp.
Address:
1700 Valley Road, Wayne
New Jersey 07470
Telephone Number: 973-317-5000
For USB wireless transmitter
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may Cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment. To maintain
compliance with FCC RF exposure compliance requirements,
please avoid direct contact to the transmitting antenna during
transmitting.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
For Canada/pour le Canada
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
For Canada/pour le Canada
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
safety_RX-D702B[J]_f.p65
1
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
05.8.25, 1:20 PM
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance
from your unit, and retain this manual for future reference.
Features
Precautions
Hybrid Feedback Digital Amplifier
RX-D702B features the JVC-exclusive Hybrid Feedback Digital
Amplifier. Premium-grade parts and devices, and special
internal construction assure you will enjoy superior sound.
USB WIRELESS
By using the USB wireless transmitter supplied with RX-D702B,
sound reproduced from your PC can be transmitted to this
receiver. You can choose PC as another playback source for
RX-D702B.
Compatible with HDMI*
The HDMI (High Definition Multimedia Interface) is the standard
interface for the next-generation TV. By connecting the source
components, this receiver, and TV with the HDMI cables, digital
video signals and audio signals (including Dolby Digital, DTS)
are transmitted through the cables. You can enjoy digital video
and sound without AD/DA conversion with easy connection.
As RX-D702B supports up to HDMI version 1.1, this receiver
can digitally transmit 5.1-channel PCM with sampling rates of
96 kHz and 2-channel PCM with sampling rates of 192 kHz.
(These PCM signals are referred to as “multi channel PCM” in
this instruction.) You can enjoy digital sound without
deterioration. In addition, this receiver is compatible with
HDCP** (High-Bandwidth Digital Content Protection), and
HDCP contents can be viewed if you connect a HDCPcompatible TV to this receiver.
Power sources
• When unplugging the receiver from the wall outlet, always pull
the plug, not the AC power cord.
• Do not handle the AC power cord with wet hands.
• If you are not going to operate the receiver for an extended
period of time, unplug the AC power cord from the wall outlet.
Ventilation
The seven high power amplifiers built in this receiver will generate
heat inside the cabinet.
For safety, observe the following carefully:
• Make sure there is good ventilation around the receiver. Poor
ventilation could overheat and damage the receiver.
• Do not block the ventilation openings or holes. (If the ventilation
openings or holes are blocked by a newspaper or cloth, etc., the
heat may not be able to get out.)
Others
• Should any metallic object or liquid fall onto the unit, unplug the
unit and consult your dealer before operating any further.
• Do not use this receiver in a bathroom or places with water.
• Do not place any containers filled with water or liquids (such as
cosmetics or medicines, flower vases, potted plants, cups, etc.)
on top of this receiver.
• Do not disassemble the unit since there are no user serviceable
parts inside.
If anything goes wrong, unplug the AC power cord and consult
your JVC dealer.
* HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
** HDCP is the abbreviation of “High-Bandwidth Digital Content
Protection,” and is the high-reliable copy control technology
licenced by Digital Content Protection, LLC.
7.1 channel DAP (Digital Acoustic Processor)
Sound field simulation technology allows precise ambience
recreation of existing theaters and halls. Thanks to the highperformance DSP (Digital Signal Processor) and high-capacity
memory, you can enjoy 7.1-channel surround by playing 2channel or multi-channel software.
K2 Technology
K2 technology has been designed to enable natural audio
reproduction, achieving a drastic reduction in digital distortion
and creating original sound ambience with high precision.
CC (Compression Compensative) Converter
CC Converter eliminates jitter and ripples, achieving a drastic
reduction in digital distortion by processing the digital music
data in 24 bit–quantization and by expanding the sampling
frequency to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs
44.1 kHz signals)/192 kHz (for fs 48 kHz signals). By using the
CC Converter, you can obtain a natural sound field from any
source.
DCDi technology
DCDi (Directional Correlational Deinterlacing) technology,
developed by Faroudja, eliminates jagged edges generated in
progressive scan conversion. With DCDi, you can enjoy clear
and smooth video images on your display. For RX-D702B, this
function is applied only when the NTSC analog video signals
are transmitted to the receiver.
1
01-08RX-D702B[J]_f.p65
1
05.8.25, 0:59 PM
Table of Contents
Parts identification ................................................ 3
Getting started ...................................................... 6
Before Installation .................................................................. 6
Checking the supplied accessories ....................................... 6
Putting batteries in the remote control ................................... 6
Connecting the FM and AM antennas ................................... 7
Connecting the speakers ....................................................... 8
Connecting audio and video components ............................. 9
Connecting the power cord .................................................. 16
USB connection ................................................................... 17
Basic operations ................................................. 19
1 Turn on the power ............................................................
2 Select the source to play ..................................................
3 Adjust the volume ............................................................
Selecting the digital decode mode .......................................
Turning off the sounds temporarily ......................................
Changing the display brightness ..........................................
Turning off the power with the Sleep Timer .........................
Making sounds natural .........................................................
19
19
20
21
21
21
22
22
Basic settings ...................................................... 23
Setting the speaker information automatically
—Smart Surround Setup ............................................... 23
Basic setting items ............................................................... 25
Operation through on-screen display menus ....................... 25
Menu operation buttons ................................................... 25
Setup menu configuration ............................................... 26
Menu operating procedure ................................................... 27
Setting the items .................................................................. 28
Setting the speakers ....................................................... 28
Activating the EX/ES/PLIIx setting—EX/ES/PLIIx ........... 30
Selecting the main or sub channel—DUAL MONO ......... 30
Setting bass sound .......................................................... 30
Using the Midnight mode—MIDNIGHT ........................... 31
Setting the digital input (DIGITAL IN) terminals
—DIGITAL IN 1/2/3 ................................................... 31
Setting the Audio delay level—AUDIO DELAY ................ 31
Memorizing the volume level for each source
—ONE TOUCH OP ................................................... 32
Selecting the source for HDMI terminal and COMPONENT
VIDEO jacks—HDMI SELECT/CMPNT SELECT ..... 32
Selecting the output video signals—VIDEO OUTPUT .... 32
Superimposing the menus—SUPERIMPOSE ................ 32
Sound adjustments ............................................. 33
Basic adjustment items ........................................................
Operation through on-screen display menus .......................
Menu operation buttons ...................................................
Setup menu configuration ...............................................
Menu operating procedure ...................................................
Adjusting the items ..............................................................
Adjusting the speaker output levels .................................
Adjusting the equalization patterns
—DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz ........
Adjusting the bass sounds ..............................................
Adjusting the sound parameters for the
Surround/DSP modes ...............................................
33
33
33
34
35
36
36
37
37
37
Tuner operations ................................................. 39
Tuning in to stations manually .............................................. 39
Using preset tuning .............................................................. 39
Selecting the FM reception mode ........................................ 40
Creating realistic sound fields ........................... 41
Reproducing theater ambience ...........................................
Introducing the Surround modes .........................................
Introducing the DSP modes .................................................
Using the Surround/DSP modes .........................................
Activating the Surround/DSP modes ...................................
AV COMPU LINK remote control system ..........
Operating other JVC products ...........................
Operating other manufacturers’ products ........
Troubleshooting ..................................................
Specifications ......................................................
41
41
43
44
45
46
48
50
53
55
2
01-08RX-D702B[J]_f.p65
2
05.8.25, 0:59 PM
Remote control
Parts identification
A/V CONTROL RECEIVER
REMOTE CONTROL RM-SRXD701J
AUDIO
TV/VIDEO
1
DBS/CATV
VCR
DVR/DVD
TV
DBS
VCR
DVR/DVD
SIRIUS
FM/AM
USB
AUX
TV/SIRIUS
2
3
4
TV VOL
CHANNEL
i
VOLUME
DVR
o
5
6
DVD
MEMO
SELECT
MUTING
TUNING/REW
– CAT –
FF/TUNING
SETTING
;
DVD MENU
7
a
DISP
8
SET
ADJUST
EXIT
9
p
s
VIDEO INPUT
1
2
3
4
5
6
BAND
PREV
AUDIO INPUT
q
DECODE MODE
w
SURROUND
e
r
7
8
RETURN
FM MODE
10
0
10
D.EQ FREQ CC CONVERTER MEMORY DIMMER
C.TONE
D.EQ LEVEL
EFFECT
MIDNIGHT
TEST
SLEEP
SMART S.SETUP
t
y
L – FRONT – R
CENTER
SUBWFR
u
L – SURR – R
d
9
100
L – S. BACK – R
f
g
h
j
k
l
See pages in parentheses for details.
1 TV/VIDEO button (48, 50)
2 Standby/on buttons (19, 48 – 52)
AUDIO, TV/SIRIUS
, DBS/CATV
, VCR
,
DVR/DVD
3 Source selecting buttons (19, 39, 48 – 52)
TV, DBS, VCR, DVR/DVD, SIRIUS, FM/AM, USB, AUX
4 TV VOL (volume) +/– button (48, 50)
5 CHANNEL +/– button* (48 – 52)
6 • Operating buttons for video components* (48, 49, 51, 52)
, 3, REW, 4, 7, 8, FF, ¢
• Operating buttons for tuner (39)
( TUNING, TUNING 9
• Operating buttons for SIRIUS tuner (48)
MEMO, SELECT, ( CAT, CAT 9
7 SETTING button (25, 27)
8 • Cursor buttons (3, 2, 5, ∞) (25, 27, 28, 33, 35, 49, 52)
• SET button (25, 28, 33, 35)
9 ADJUST button (33, 35)
p VIDEO INPUT button (20)
q AUDIO INPUT button (20)
w DECODE MODE button (21)
e SURROUND button (30, 45)
r Adjusting buttons for Digital Equalizer (37)
D.EQ FREQ, D.EQ LEVEL +/–
t CC CONVERTER button (22)
y Adjusting buttons for Surround/DSP modes’ parameters
C (center).TONE, EFFECT (37, 38)
u Adjusting buttons for speaker and subwoofer output levels (36)
FRONT L +/–, FRONT R +/–, CENTER +/–, SUBWFR +/–,
SURR L +/–, SURR R +/–, S.BACK L +/–, S.BACK R +/–
i VOLUME +/– button (20)
o DVR/DVD mode selector* (49, 52)
; MUTING button (21)
a • DVD MENU button* (49, 52)
• DISP button (48)
s EXIT button (25, 28, 33, 35)
d • Numeric buttons* (40, 42, 48 – 52)
1 – 10, 0, +10, 100+
• BAND button (48)
• PREV button (48)
• RETURN button (48)
• FM MODE button (40)
f DIMMER button (21)
g MEMORY button (39, 40)
h SLEEP button (22)
j MIDNIGHT button (31)
k SMART S (surround). SETUP button (23, 24)
l TEST button (36)
* These buttons can be used for operating a JVC DVD recorder
or DVD player with the mode selector set to “DVR” or “DVD”
(see page 49).
If these buttons do not function normally, use the remote control
supplied with your DVD recorder or DVD player. Refer also to
the manuals supplied with the DVD recorder or DVD player for
details.
To open the cover of the remote
control, push here then slide
downward.
• When operating a DVD recorder (for JVC products
ONLY), set the mode selector (o) to “DVR.”
• When operating a DVD player, set the mode selector (o)
to “DVD.”
3
01-08RX-D702B[J]_f.p65
3
05.8.25, 0:59 PM
See pages in parentheses for details.
Front panel
1
2 3 4 5
6 7
8
SETTING
ADJUST
MASTER
VOLUME
/ MULTI JOG
HDMI
CC CONVERTER
p
SOURCE
SELECTOR
AUDIO/VIDEO CONTROL RECEIVER
STANDBY/ON
9
DVR / DVD
VCR
DBS
TV/SIRIUS
USB
FM/AM
AUX
SURROUND
SET / TUNER PRESET
PUSH-OPEN
r
t
How to open the front door
S-VIDEO
PHONES
DIGITAL
USB
VIDEO
L – AUDIO – R
AUX
q
w
e
Inside the front door
Press down on PUSH-OPEN.
1
2
3
4
5
6
7
STANDBY/ON button and standby lamp (19)
CC CONVERTER button (22)
SETTING button (25, 27)
ADJUST button (33, 35)
SURROUND button (45)
HDMI lamp (9, 20)
Source lamps (19)
DVR/DVD, VCR, DBS, TV/SIRIUS, USB, FM/AM, AUX
8 • SET button (25, 28, 33, 35)
• TUNER PRESET button (40)
9 • SOURCE SELECTOR (19, 40)
• MULTI JOG (25, 27, 28, 33, 35, 45)
p MASTER VOLUME control (20)
q PHONES jack (20)
w USB terminal (17)
e AUX input jacks (15)
Digital optical terminal, S-video jack, VIDEO jack,
AUDIO jacks
r Display window (5)
t Remote sensor (6)
4
01-08RX-D702B[J]_f.p65
4
05.8.25, 0:59 PM
Display window
1
2
3
5
4
7
6
89
0
-
=~
ANALOG DUAL MONO AUTO SURR RDS TA NEWS INFO TUNED STEREO AUTO MUTING ONE TOUCH OPERATION SLEEP
DIGITAL AUTO L C R HEADPHONE CC CONVERTER 1 2 AUTO MODE DIGITAL EQ C.TONE B.BOOST MIDNIGHT INPUT ATT
LINEAR PCM S.WFR LFE
PL x
DIGITAL
NEO : 6 DSP
LS S RS 3D-PHONIC
MHz
96 / 24
SB SB SB VIRTUAL SB
kHz
!
1
2
3
4
5
6
7
8
9
0
=
~
@
#$
%^ &
*
(
)
_
! Digital signal format indicators (20, 21, 41, 42)
LINEAR PCM,
,
, 96/24
@ Signal and speaker indicators (22)
# NEO:6 indicator (42)
$ VIRTUAL SB (surround back) indicator (44)
% 3D-PHONIC indicator (42, 43)
^ DSP indicator (43)
&
and
indicator (41 – 43)
* Main display
( B (bass).BOOST indicator (37)
) MIDNIGHT indicator (31)
_ Frequency unit indicators
MHz (for FM stations), kHz (for AM stations)
ANALOG indicator (20)
DIGITAL and DIGITAL AUTO indicator (20, 21)
DUAL MONO indicator (30)
AUTO SURR (surround) indicator (45)
HEADPHONE indicator (20, 43)
CC CONVERTER 1 and CC CONVERTER 2 indicator (22)
Tuner operation indicators (39)
TUNED, STEREO
DIGITAL EQ indicator (37)
AUTO MUTING indicator (40)
C (center).TONE indicator (38)
ONE TOUCH OPERATION indicator (32)
INPUT ATT (attenuate) indicator (37)
SLEEP indicator (22)
Rear panel
1
2
VCR(DBS) IN
3 4
DVR/DVD IN
5
6
7
USB WIRELESS
MONITOR OUT
8
AM LOOP
ANTENNA
SUBWOOFER
OUT
ANTENNA
HDMI
AV
COMPU LINK-III
DIGITAL OUT
DIGITAL IN
1(DVR/DVD)
2(DBS)
3(VCR)
ON
ID LEARNING
FM 75
PCM/STREAM
COAXIAL
AM EXT
CAUTION:SPEAKER IMPEDANCE 6 -16
COMPONENT VIDEO
DVD
MULTI IN
AUDIO
VIDEO
Y
TV/SIRIUS
L IN
DBS
IN
VCR
OUT(REC)
IN(PLAY)
DVR
DVR/DVD
OUT(REC)
IN(PLAY)
CENTER
SURR-L
FRONT
SUBWOOFER
SURR-R
VIDEO
PB
S-VIDEO
PR
DBS
IN
VCR
OUT(REC) IN(PLAY)
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
MONITOR
OUT
VCR(DBS) DVR/DVD
IN
IN
9
1 Power cord (16)
2 HDMI terminals (10, 11, 13, 14)
VCR(DBS) IN, DVR/DVD IN, MONITOR OUT
3 AV COMPU LINK-III terminals (46)
4 DIGITAL IN terminals (16)
• Coaxial: 1(DVR/DVD)
• Optical: 2(DBS)
• Optical: 3(VCR)
5 DIGITAL OUT terminal (16)
6 • USB WIRELESS ANTENNA terminal (17)
• USB WIRELESS switch (17)
• USB WIRELESS lamp (17)
7 ANTENNA terminals (7)
8 SUBWOOFER OUT jack (8)
RIGHT
R
MONITOR
OUT
p
LEFT
SURROUND BACK SPEAKERS
q
RIGHT
LEFT
RIGHT
SURROUND SPEAKERS
CENTER
SPEAKER
LEFT
FRONT SPEAKERS
e
w
9 VIDEO jacks (10 – 14)
VIDEO (composite video) jacks, S-VIDEO jacks
• Input: DBS IN, VCR IN (PLAY), DVR/DVD IN (PLAY)
• Output: VCR OUT (REC), DVR OUT (REC), MONITOR OUT
p COMPONENT VIDEO (Y, PB, PR) jacks (10 – 14)
VCR(DBS) IN, DVR/DVD IN, MONITOR OUT
q AUDIO jacks (10 – 14)
• Input: TV/SIRIUS IN, DBS IN, VCR IN (PLAY),
DVR/DVD IN (PLAY)
• Output: VCR OUT (REC), DVR OUT (REC)
w DVD MULTI IN jacks (12)
CENTER, SUBWOOFER, SURR – L, SURR – R
e Speakers terminals (8)
SURROUND BACK SPEAKERS, SURROUND SPEAKERS,
CENTER SPEAKER, FRONT SPEAKERS
5
01-08RX-D702B[J]_f.p65
5
05.8.25, 0:59 PM
Getting started
Putting batteries in the remote control
Before using the remote control, put two supplied batteries first.
1
Before Installation
General precautions
• Be sure your hands are dry.
• Turn the power off to all components.
• Read the manuals supplied with the components you are going
to connect.
Locations
• Install the receiver in a location that is level and protected from
moisture and dust.
• The temperature around the receiver must be between –5˚C
and 35˚C (23˚F and 95˚F).
• Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
• Leave sufficient distance between the receiver and the TV.
Handling the receiver
• Do not insert any metal object into the receiver.
• Do not disassemble the receiver or remove screws, covers, or
cabinet.
• Do not expose the receiver to rain or moisture.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• When you are away on travel or otherwise for an extended
period or time, remove the plug from the wall outlet. A small
amount of power is always consumed while the power cord is
connected to the wall outlet.
1
2
2
3
Press and slide the battery cover on the back
of the remote control.
Insert batteries.
Make sure to match the polarity: (+) to (+) and (–) to (–).
3
Replace the cover.
If the range or effectiveness of the remote control decreases,
replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell
batteries.
• Supplied butteries are for initial setup. Replace for continued
use.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
When using the remote control, aim the remote control directly at
the remote sensor on the front panel.
Remote sensor
The receiver has a built-in cooling fan which operates
while the receiver is turned on. Be sure to leave enough
ventilation to obtain sufficient cooling effect.
CAUTION:
Do not connect the AC power plug to the wall outlet until all
connections are completed.
Checking the supplied accessories
Check to be sure you have all of the following supplied
accessories. If anything is missing, contact your dealer
immediately.
•
•
•
•
•
•
•
Remote control (× 1)
Batteries (× 2)
AM loop antenna (× 1)
FM antenna (× 1)
USB wireless antenna (× 1)
USB wireless transmitter (Model number: QAL0708-001) (× 1)
USB extension cable (60 cm) (× 1)
6
01-08RX-D702B[J]_f.p65
6
05.8.25, 0:59 PM
Connecting the FM and AM antennas
Do not connect the AC power plug to the wall outlet until all connections are completed.
AM loop antenna
(supplied)
If FM reception is poor, connect an
outdoor FM antenna (not supplied).
Snap the tabs on the
loop into the slots of
the base to assemble
the AM loop antenna.
AM LOOP
If AM reception is poor, connect
an outdoor single vinyl-covered
wire (not supplied).
ANTENNA
FM 75
COAXIAL
AM EXT
FM antenna (supplied)
A
ENN
ANT
AM antenna connection
Connect the AM loop antenna supplied to the AM LOOP
terminals.
Connect the white cord to the AM EXT terminal, and connect the
black cord to the H terminal.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinyl-covered
wire (not supplied) to the AM EXT terminal. Keep the AM loop
antenna connected.
NOTES
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown on the
right.
• Make sure the antenna conductors do not touch
any other terminals, connecting cords and power
cord. This could cause poor reception.
FM antenna connection
Connect the FM antenna supplied to the FM 75 Ω COAXIAL
terminal as a temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable with a
connector, disconnect the supplied FM antenna.
7
01-08RX-D702B[J]_f.p65
7
05.8.25, 0:59 PM
Connecting the speakers
Do not connect the AC power plug to the wall outlet until all connections are completed.
Speaker Layout Diagram
SW
C
FL
Right surround
back speaker
(SBR)
SR
SL
SBL
Center
speaker (C)
FR
SBR
(*SB)
SUBWOOFER
OUT
CAUTION:SPEAKER IMPEDANCE 6 -16
*Left surround
back speaker
(SBL)
RIGHT
LEFT
SURROUND BACK SPEAKERS
RIGHT
LEFT
SURROUND SPEAKERS
RIGHT
CENTER
SPEAKER
LEFT
FRONT SPEAKERS
Right surround
speaker (SR)
Left surround
speaker (SL)
Right front
speaker
(FR)
Powered
subwoofer
(SW)
Left front
speaker
(FL)
CAUTIONS:
*When using a single speaker for the surround back speaker
• Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals (6 Ω – 16 Ω).
• DO NOT connect more than one speaker to one speaker
terminal.
You can enjoy the surround sound by one surround back
speaker. When using one surround back speaker,
– set “S BACK OUT” to “S BACK OUT: 1SPK” (see page 29) and
– connect the surround back speaker to the left surround back
speaker terminal. (No sound comes from the speaker if
you connect it to the right surround back speaker
terminal.)
Connecting the speakers
Turn off all components before making connections.
Connecting the powered subwoofer
1
2
3
4
By connecting a subwoofer, you can enhance the bass or
reproduce the original LFE signals recorded in digital software.
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cord
with RCA pin plugs (not supplied).
• Refer also to the manual supplied with your subwoofer.
1
Twist and remove the insulation at the end of each
speaker cord.
After connecting all the speakers and/or a subwoofer, set the
speaker setting information properly to obtain the best possible
surround effect. For details, see pages 23, 24, 28, and 29.
NOTE
2
Turn the knob counterclockwise.
3
Insert the speaker cord.
You can place a subwoofer wherever you like since bass sound is
non-directional. Normally place it in front of you.
• For each speaker, connect the (+) and (–) terminals on the
rear panel to the (+) and (–) terminals marked on the
speakers.
4
Turn the knob clockwise.
8
01-08RX-D702B[J]_f.p65
8
05.8.25, 0:59 PM
Connecting audio and video components
Do not connect the AC power plug to the wall outlet until all connections are completed.
Video conversion function
This receiver can convert the video signals output from video components. The chart below shows which video signals can be converted
into which signals by video conversion.
Video Input
Converted
Video Output
HDMI
HDMI
CMPNT (component)
CMPNT (component)
S (S-video)
S (S-video)
C (composite)
C (composite)
To use the video conversion function, you need to make the two
settings below when you finish connecting your TV and video
components.
VIDEO OUTPUT:
Select the settings according to the
connection method for your TV. See
page 32 for details.
VIDEO INPUT:
Select the settings according to the
connection method for your video
components. This setting is memorized
for each source. See pages 11 to 15 and
20 for details.
Converted video signals available vary depending on each source component. See also pages 10 to 15 for details.
NOTES
• HDMI signals cannot be converted into other video signals.
• With input video signals converted into HDMI signals, the playback picture may be distorted when you change the playback mode
(fast-forward, rewind, or pause, for example).
Before connecting video components
Before connecting video components, note the folllowing below.
IMPORTANT:
The HDMI video signals from the HDMI terminal are transmitted only through the HDMI MONITOR OUT terminal.
Therefore, if the TV is connected to the receiver through the VIDEO jack (MONITOR OUT), S-VIDEO jack (MONITOR OUT), or
COMPONENT VIDEO jacks (MONITOR OUT) and a playing video component is connected to the receiver through the HDMI terminal
(VCR (DBS) IN or DVR/DVD IN), you cannot view the playback picture on the TV.
NOTES
• When playing back audio and video with the HDMI connection, the HDMI lamp on the front panel lights up.
• Set the audio input setting to “HDMI” when you enjoy sound with the HDMI connection. See “Selecting the audio input setting” on page
20.
• When connecting a VCR or DBS to HDMI VCR (DBS) IN terminal, select “HDMI SELECT” (see page 32) correctly according to the
component you connect. If you do not, you cannot view the playback picture on the TV.
• By using a HDMI-DVI conversion cable, you can connect the source components or the TV with DVI output. When connecting those
components or TV, change the audio input setting to the setting other than “HDMI.” (See page 20.)
• This receiver is compatible with standard video formats. If non-standard video formats are coming in, the picture may not appear
properly on TV.
• The picture on the TV may not be the same aspect ratio as the ratio set on the source components.
• When connecting a TV to this receiver with an HDMI cable, the sound coming into this receiver is not transmitted to the speakers of the
TV. You can enjoy sound only from the speakers connected to this receiver.
• When connecting a TV to this receiver with an HDMI cable, turning a source component on or off, or changing the audio or video input
setting of this receiver frequently may cause a noise or interrupt the sound and picture. In this case, turn the receiver off and turn it on
again.
• When enjoying multi channel PCM sound with the audio input setting set to “HDMI” (see page 20), some functions are not available.
See page 12 for details.
• When you enjoy HDCP contents, sound and picture may not be transmitted to the speakers and TV for a few seconds in the beginning
for confirmation.
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound
output through this receiver may be distorted.
9
09-15RX-D702B[J]_f.p65
9
05.8.25, 0:59 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a TV:
Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video components.
Turn off all components before making connections.
: signal current
• When you connect other components, refer also to their manuals.
HDMI cable (not supplied)
MONITOR OUT
TV/SIRIUS
L IN
White
DB
IN
Stereo audio cable
(not supplied)
Red
Å
ı
TV
R
COMPONENT VIDEO
/DVD
PLAY)
MONITOR
OUT
Green
Y
Blue
PB
Red
Component video cable
(not supplied)
Ç
PR
VCR(DBS) DVR/DVD
IN
IN
Î
‰
MONITOR
OUT
S-video cable (not supplied)
Composite video cable (not supplied)
Select the appropriate VIDEO OUTPUT (see page 32)
according to the terminal used for TV connection referring
to the table below.
Connection method
HDMI
Component video
S-video
Composite video
VIDEO OUTPUT
HDMI
CMPNT
S
C
Å To left/right audio channel output
ı To HDMI input
Ç To component video input
• Connect Y, PB, and PR correctly.
Î To S-video input
‰ To composite video input
DO NOT use a TV through a VCR or a TV with a built-in
VCR; otherwise, the picture may be distorted.
NOTES
• If connecting a TV only with the HDMI cable and setting the video input setting (see page 20) to “HDMI,” the on-screen display does
not appear on the TV screen. When using on-screen display, set the video input setting to the setting other than HDMI.
• Select the audio and video input setting according to the connection method. See page 20 for details.
• In addition to using the HDMI cable, you can enjoy digital sound as well using a digital audio cable (coaxial or optical). For details of
digital audio connection, see page 16.
• When you enjoy contents protected by HDCP (High-Bandwidth Digital Content Protection, see page 1), connect a HDCP-compatible
TV to this receiver, otherwise, the picture may not appear properly.
10
09-15RX-D702B[J]_f.p65
10
05.8.25, 0:59 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a DVD recorder or DVD player
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
: signal current
HDMI cable (not supplied)
Red
) IN
White
DVR/DVD IN
HDMI
DVR
DVR/DVD
OUT(REC)
IN(PLAY)
White
Stereo audio cable
(not supplied)
Red
Å
ı
Ç
DVD recorder or
DVD player
FRONT
Î
COMPONENT VIDEO
Green
Y
Blue
PB
Red
DVR
DVR/DVD
OUT(REC) IN(PLAY)
Component video cable
(not supplied)
PR
VCR(DBS) DVR/DVD
IN
IN
‰ Ï Ì Ó
MONITOR
OUT
Composite video cable (not supplied)
S-video cable (not supplied)
Composite video cable (not supplied)
Select the appropriate VIDEO INPUT (see page 20) according
to the connection you have made. If you do not, you cannot
view the playback picture on the TV.
Available video input setting for each video output setting:
: Available –: Not available
VIDEO
OUTPUT
VIDEO INPUT
HDMI
CMPNT
HDMI
CMPNT
–
S
C
–
–
S
C
Å To left/right audio channel output
ı Only for DVD recorder: To left/right front channel
audio input
Ç To HDMI output
Î To component video output
• Connect Y, PB, and PR correctly.
‰ To composite video output
Ï To S-video output
Ì Only for DVD recorder: To S-video input
Ó Only for DVD recorder: To composite video input
–
–
NOTES
• Select the audio and video input setting according to the connection method. See page 20 for details.
• In addition to using the HDMI cable, you can enjoy digital sound as well using a digital audio cable (coaxial or optical). When shipped
from the factory, the digital coaxial terminal (DIGITAL IN 1 (DVR/DVD)) on the rear of the receiver is set for a DVD recorder and DVD
player. For details of digital audio connection, see page 16.
• If your DVD recorder or DVD player is equipped with the analog multi channel output terminals, you can enjoy the sound recorded in
DVD-Audio by connecting your DVD recorder or DVD player to DVD MULTI IN jacks. See page 12 for details.
When you enjoy the sound recorded in DVD-Audio with HDMI connection, see “When you enjoy sound recorded in DVD-Audio...” on
page 12.
11
09-15RX-D702B[J]_f.p65
11
05.8.25, 0:59 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
When you connect a DVD recorder or DVD player with its analog discrete output jacks (DVD MULTI IN):
If your DVD recorder or DVD player has analog 5.1 channel output jacks, use the connection below. When a DVD Audio disc is played
back, the original high-quality sounds can be reproduced by using this connection.
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
Green
COMPONENT VIDEO
Y
Blue
PB
Red
: signal current
Component video cable (not supplied)
Monaural audio cable
(not supplied)
PR
VCR(DBS) DVR/DVD
IN
IN
MONITOR
OUT
DVD
MULTI IN
Å
SUBWOOFER
DVR
DVR/DVD
IN(PLAY)
ı
DVD recorder or
DVD player
SURR-R
Monaural audio cable
(not supplied)
OUT(REC)
Ç
Stereo audio cable
(not supplied)
SURR-L
CENTER
White
‰ Ï
Ì Ó È Ô
Î
Red
DVR
OUT(REC)
DVR/DVD
IN(PLAY)
FRONT
Red
Stereo audio cable
(not supplied)
White
Composite video cable
(not supplied)
S-video cable (not supplied)
Composite video cable (not supplied)
Å To left/right surround channel audio output
ı To center channel audio output
Ç To component video output
• Connect Y, PB, and PR correctly.
Î To subwoofer output
‰ To left/right front channel audio output
When you enjoy sound recorded in DVD-Audio...
You can enjoy sound recorded in DVD-Audio both with analog
or digital methods.
– With analog method:
• connect your DVD recorder or DVD player to this receiver
according to the diagram above.
• select “A MULTI” in the audio input setting. (See page 20.)
– With digital method:
• connect your DVD recorder or DVD player and TV to this
receiver with the HDMI cables. (See page 11.)
• select “HDMI” in the audio input setting. (See page 20.)
NOTES
• When selecting “A MULTI” in the audio input setting or when
multi channel PCM signals (see page 42) are coming in with
selecting “HDMI” in the audio input setting, you can listen to
the front channel sounds (left and right) only by using the
headphones. 3D HEADPHONE mode (see page 43) is not
available.
Ï Only for DVD recorder: To left/right front channel
audio input
Ì To composite video output
Ó To S-video output
È Only for DVD recorder: To S-video input
Ô Only for DVD recorder: To composite video input
• When selecting “A MULTI” in the audio input setting or when
multi channel PCM signals (see page 42) are coming in with
selecting “HDMI” in the audio input setting, the following items
are not available:
– DECODE MODE (see page 21)
– CC Converter (see page 22)
– EX/ES/PLllx (see page 30)
– DUAL MONO (see page 30)
– SUBWFR OUT (see page 30)
– CROSSOVER (see page 31)
– LFE ATT (see page 31)
– MIDNIGHT (see page 31)
– AUDIO DELAY (see page 31)
– DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz (see page 37)
– BASS BOOST (see page 37)
– INPUT ATT (see page 37)
– Sound parameters for Surround/DSP modes (see pages 37
and 38)
– Surround/DSP modes (see pages 41 to 45)
• When you enjoy sound recorded in DVD-Audio through the
HDMI connection, use a DVD recorder or DVD player
compatible with HDMI version 1.1.
12
09-15RX-D702B[J]_f.p65
12
05.8.25, 7:23 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a VCR:
Turn off all components before making connections.
: signal current
• When you connect other components, refer also to their manuals.
HDMI cable (not supplied)
VCR(DBS) IN
HDMI
VCR
OUT(REC)
Å
Stereo audio cable
(not supplied)
AUDIO
ı
VCR
Å
IN(PLAY)
Ç
Î
Green
COMPONENT VIDEO
VCR
OUT(REC) IN(PLAY)
Y
Blue
PB
Red
‰ Ï
Ì Ó
Component video cable
(not supplied)
PR
VCR(DBS)
IN
DVR/DVD
IN
MONITOR
OUT
Composite video cable (not supplied)
S-video cable (not supplied)
Composite video cable (not supplied)
Select the appropriate VIDEO INPUT (see page 20) according
to the connection you have made. If you do not, you cannot
view the playback picture on the TV.
Available video input setting for each video output setting:
: Available –: Not available
VIDEO
OUTPUT
VIDEO INPUT
HDMI
CMPNT
S
C
Å
ı
Ç
Î
‰
Ï
Ì
Ó
To left/right audio channel input
To HDMI output
To left/right audio channel output
To component video output
• Connect Y, PB, and PR correctly.
To composite video output
To S-video output
To S-video input
To composite video input
HDMI
CMPNT
–
S
C
–
–
–
–
NOTES
• Select the audio and video input setting according to the connection method. See page 20 for details.
• In addition to using the HDMI cable, you can enjoy digital sound as well using a digital audio cable (coaxial or optical). When shipped
from the factory, the digital optical terminal (DIGITAL IN 3 (VCR)) on the rear of the receiver is set for a VCR. For details of digital audio
connection, see page 16.
• When connecting a VCR with a HDMI cable or component video cable, set “HDMI SELECT” or “CMPNT SELECT” to “VCR.” (see page
32)
13
09-15RX-D702B[J]_f.p65
13
05.8.25, 0:59 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a DBS tuner:
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
: signal current
Composite video cable (not supplied)
S-video cable (not supplied)
HDMI cable (not supplied)
VIDEO
VIDEO
VCR(DBS) IN
S-VIDEO
DBS
IN
HD
OU
Å
DBS
IN
OU
White
ı
Ç
Stereo audio cable
(not supplied)
Red
Î
‰
DBS tuner
Green
COMPONENT VIDEO
Y
Blue
PB
Red
Component video cable (not supplied)
PR
VCR(DBS) DVR/DVD
IN
IN
MONITOR
OUT
Select the appropriate VIDEO INPUT (see page 20) according
to the connection you have made. If you do not, you cannot
view the playback picture on the TV.
Available video input setting for each video output setting:
: Available –: Not available
VIDEO
OUTPUT
Å
ı
Ç
Î
‰
To HDMI output
To S-video output
To composite video output
To left/right audio channel output
To component video output
• Connect Y, PB, and PR correctly.
VIDEO INPUT
HDMI
CMPNT
S
C
HDMI
CMPNT
–
S
C
–
–
–
–
NOTES
• Select the audio and video input setting according to the connection method. See page 20 for details.
• In addition to using the HDMI cable, you can enjoy digital sound as well using a digital audio cable (coaxial or optical). When shipped
from the factory, the digital optical terminal (DIGITAL IN 2 (DBS)) on the rear of the receiver is set for a DBS tuner. For details of digital
audio connection, see page 16.
• When connecting a DBS tuner with a HDMI cable or component video cable, set “HDMI SELECT” or “CMPNT SELECT” to “DBS.” (see
page 32)
14
09-15RX-D702B[J]_f.p65
14
05.8.25, 0:59 PM
Do not connect the AC power plug to the wall outlet until all connections are completed.
7 Connecting a video component to the AUX input jacks
The AUX input jacks on the front panel (inside the front door) are convenient when connecting and disconnecting the component
frequently.
Before making connections, press PUSH-OPEN to show the jacks.
To enjoy the playback from the component connected to these jacks, select “AUX” as the source (see page 19).
How to open the front door
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
S-VIDEO
DIGITAL
VIDEO
L – AUDIO – R
Red
AUX
Video camera, etc.
Stereo audio cable
(not supplied)
White
Å
ı Ç
Î
Composite video cable (not supplied)
S-video cable (not supplied)
Digital optical cable (not supplied)
: signal current
Select the appropriate VIDEO INPUT (see page 20) according
to the connection you have made. If you do not, you cannot
view the playback picture on the TV.
Å
ı
Ç
Î
To left/right audio channel output
To composite video output
To S-video output
To digital optical output
Available video input setting for each video output setting:
: Available –: Not available
VIDEO INPUT
VIDEO
OUTPUT
HDMI
CMPNT
HDMI
–
–
CMPNT
–
–
S
C
–
–
–
–
S
NOTE
C
7 Connecting a SIRIUS radio
Select the audio and video input setting according to the
connection method. See page 20 for details.
Turn off all components before making connections.
• When you connect other components, refer also to their manuals.
5
3
2
∞
TV/SIRIUS
L IN
DB
IN
White
Red
Stereo audio cable
(not supplied)
R
SIRIUS radio
NOTES
• To connect KT-SR2000 (JVC SIRIUS radio) to this receiver, it is required to separately purchase KS-K6013 Home Docking Kit.
• You cannot use a digital audio cable (coaxial or optical) to connect a SIRIUS radio to this receiver.
• After connecting a SIRIUS radio to the TV IN jacks, change the source name to “SIRIUS.” See page 19 for details.
15
09-15RX-D702B[J]_f.p65
15
05.8.25, 0:59 PM
Digital audio connection
7 Digital output terminal
This receiver is equipped with three DIGITAL IN terminals—one
digital coaxial terminal and two digital optical terminals—and one
DIGITAL OUT terminal on the rear of the receiver.
To reproduce the digital sound, use the digital audio connection in
addition to the analog audio connection methods described on
pages 10 to 15.
You can connect any digital components which have an optical
digital input terminal.
Digital coaxial cable (not supplied)
Digital optical cable (not supplied)
DIGITAL OUT
PCM/STREAM
Turn off all components before making connections.
• When you connect other components, refer also to their
manuals.
Connecting digital recording equipment to the
DIGITAL OUT terminal enables you to perform
digital-to-digital recording.
7 Digital input terminals
NOTES
When the component has a digital coaxial output
terminal, connect it to the 1(DVR/DVD) terminal,
using a digital coaxial cable (not supplied).
• The digital signal format transmitted through the DIGITAL OUT
terminal is the same as that of the input signal. For example,
when the DTS signals are coming, the DTS signals are
transmitted.
• The digital audio signals coming through the following terminals
cannot be transmitted through the DIGITAL OUT terminal:
– USB WIRELESS ANTENNA terminal
– USB terminal
– HDMI VCR(DBS) IN terminal and HDMI DVR/DVD IN terminal
DIGITAL IN
1(DVR/DVD)
2(DBS)
3(VCR)
Connecting the power cord
When the component has a digital optical output
terminal, connect it to the 2(DBS) or 3(VCR)
terminal, using a digital optical cable (not supplied).
When all the audio/video connections have been made, connect
the AC power plug to the wall outlet. Make sure that the plugs are
inserted firmly. The standby lamp lights in red.
CAUTIONS:
Before connecting a digital
optical cable, unplug the
protective plug.
NOTES
• When shipped from the factory, the DIGITAL IN terminals on the
rear of the receiver have been set for use with the following
components:
– 1(DVR/DVD): For DVD recorder or DVD player
– 2(DBS):
For DBS tuner
– 3(VCR):
For VCR
If you connect other components, change the digital input
(DIGITAL IN) terminal setting correctly. See “Setting the digital
input (DIGITAL IN) terminals—DIGITAL IN 1/2/3” on page 31.
• Select the correct digital input mode. See “Selecting the audio
input setting” on page 20.
• Do not touch the power cord with wet hands.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
NOTES
• Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen
interference.
• The preset settings such as preset channels and sound
adjustment may be erased in a few days in the following cases:
– When you unplug the power cord.
– When a power failure occurs.
• When you unplug the power cord with the receiver on and
connect the power cord again, the receiver enters standby
mode.
16
16-18RX-D702B[J].p65
16
05.8.25, 1:00 PM
USB connection
This receiver is equipped with a USB terminal on the front panel
and a USB WIRELESS ANTENNA terminal on the rear. You can
enjoy the sound reproduced through your PC with either of the
following methods:
1 connecting a USB wireless antenna (supplied) to the USB
WIRELESS ANTENNA terminal and a USB wireless
transmitter (supplied) to your PC. (USB WIRELESS)
2 connecting your PC to the USB terminal with a USB cable (not
supplied). (USB TERMINAL)
When you connect your PC for the first time, follow the procedure
below.
• Remember you cannot send any signal or data to your PC from
this receiver.
• Use USB extension cable (supplied) if it is difficult to connect
the transmitter directly to the USB connector or the transmitter
becomes obstacle to other USB connectors.
4
Turn on the receiver, then slide the USB WIRELESS
switch on the rear to “ID LEARNING,” and select the
source as “USB WIRELESS.”
When you slide the switch, the lamp in the switch starts
flashing.
5
Set the volume to minimum.
IMPORTANT:
Always set volume to “0” when connecting or disconnecting
the other equipment.
6
Press and hold ID on the transmitter to make a wireless
communication with the receiver.
When you press and hold the button, the ID lamp on the
transmitter flashes.
USB WIRELESS TRANSMITTER
IMPORTANT:
CHANNEL
Check if your PC equipped with the CD-ROM drive is running on
Windows® 98 SE*, Windows® Me*, Windows® 2000* or Windows®
XP* and prepare its CD-ROM.
Preparation
1
7
Connect the antenna to the USB WIRELESS ANTENNA
terminal on the rear panel.
• Tighten the screw with the antenna upright.
USB wireless
antenna
(supplied)
USB WIRELESS
ANTENNA
ON
POWER
ID
PLAYER
When the receiver recognizes the transmitter, the lamp on the
rear of the receiver stops flashing and lights up.
1 For USB WIRELESS
Be sure to make USB WIRELESS communication
before connection and installation of the receiver.
During the procedure, you need to check the status
of the lamp on the rear of the receiver (turning on or
flashing).
ID
Slide the switch on the receiver to “ON.”
• If you do not, no sound signal is transmitted to the receiver.
NOTES
• The signal-reachable distance is about 30 m (100 ft.), but it may
differ depending on the operating conditions and circumstances.
• The PLAYER lamp on the transmitter keeps flashing when
starting the playback software in your PC.
• If no signals are transmitted from the transmitter for about 30
minutes, the transmitter enters “sleep” mode. The “L” and “R”
indicators go off from the display.
• Though the transmitter may become hot, it is not a malfunction.
2 For USB TERMINAL
1
Turn on your PC.
• If the PC has been turned on, quit all the applications now
running.
2
Turn on the receiver, and select the source as “USB
TERMINAL.”
3
Set the volume to minimum.
ID LEARNING
IMPORTANT:
Always set volume to “0” when connecting or disconnecting
the other equipment.
2
Turn on your PC.
• If the PC has been turned on, quit all the applications now
running.
3
Connect the USB wireless transmitter to the USB
connector of the PC.
Before connecting the transmitter to the PC, remove the cover
of the transmitter.
When you connect the transmitter, the USB drivers are
installed. The POWER and PLAYER lamp on the transmitter
light up.
USB wireless
transmitter (supplied)
4
Connect the receiver to the PC using a USB cable (not
supplied).
USB
PC
PC
USB cable
(not supplied)
USB WIRELESS TRANSMITTER
USB WIRELESS TRANSMITTER
POWER
ID
PLAYER
• Use “USB series A plug to B plug” cable when connecting.
CONTINUED ON THE NEXT PAGE
17
16-18RX-D702B[J].p65
17
05.8.25, 1:00 PM
How to install the USB drivers
The following procedure is described using the English version of
WindowsR XP. If your PC is running on a different version of
operation system in a different language, the screens shown on
your PC's monitor will differ from the ones used in the following
procedure.
The following procedure is applied both to USB WIRELESS and
USB TERMINAL.
1
The USB drivers are installed automatically.
• If the USB drivers are not installed automatically, install the
USB drivers by following the instructions on the PC’s
monitor.
2
Check if the drivers are correctly installed.
1. Open the Control Panel on your PC:
Select [Start] = [Control Panel].
2. Select [System] = [Hardware] = [Device Manager] =
[Sound, video and game controllers] = [Universal Serial
Bus controllers].
• The following window appears, and you can check whether
the drivers are installed.
If no sound comes from the speakers, check the following
items:
For both USB WIRELESS and USB TERMINAL
– check the USB device is recognized properly.
– check the playback software in your PC is compatible with the
USB device.
– open the Control Panel on your PC, select [Sounds and Audio
Devices] = [Audio] tab = [Sound playback] = [Default device],
and check [Default device] is set to [USB Audio device].
For USB WIRELESS
– select “USB WIRELESS” as the source.
– connect the USB wireless transmitter correctly with the USB
WIRELESS switch on the receiver “ON.”
– keep proper distance between the receiver and your PC.
– check the ID lamp on the transmitter and the signal indicators
“L” and “R” on the display light up.
For USB TERMINAL
– select “USB TERMINAL” as the source.
– connect the USB cable correctly.
NOTES
• DO NOT turn off the receiver or disconnect the transmitter or
the USB cable while installing the drivers and for several
seconds while your PC is recognizing the receiver.
• If your PC does not recognize the receiver, disconnect the
transmitter or the USB cable and connect it again. If it does not
work yet, restart Windows.
• The installed drivers can be recognized only when the
transmitter is connected to your PC or the USB cable is
connected between the receiver and your PC.
• The sound may not be played back correctly—interrupted or
degraded—due to your PC settings and PC specifications.
• In case that the transmitter has an influence on the wireless
systems (based on IEEE 802.11b/11g, the cordless telephone,
and the microwave oven), try measures below:
– press CHANNEL on the transmitter to search for another
frequency. Each time you press CHANNEL, the frequency
advances one channel up from CH 1 up to CH 13.
– press and hold CHANNEL for more than three seconds to
make sure the transmitter detects the best frequency
automatically.
– to keep the distance between the transmitter and the LAN
antenna utilize the supplied extension cord.
• Use a USB cable (version 1.1 or later). Recommended cord
length is 1.5 m.
Now PC is ready for playback through the USB connection.
After installation is completed, you can use your PC as the
playback source. The PC automatically recognizes the receiver
whenever the transmitter is connected to the PC or the USB cable
is connected between the PC and the receiver while the receiver
is turned on.
• When not using the PC as the playback source, disconnect the
transmitter or the USB cable.
* Microsoft®, Windows® 98 SE, Windows® Me, Windows® 2000,
and Windows® XP are registered trademarks of Microsoft
corporation.
To play back sounds on the PC, refer to the manuals supplied
with the sound reproduction application installed in the PC. Start
the application after the USB device is recognized.
When playing back with USB WIRELESS,
connect the transmitter and aim the transmitter at the antenna. If
any obstacles are in between, playback will be interrupted or the
wireless communication will be canceled.
If noise comes during playback or playback is interrupted
with USB WIRELESS, try measures below:
– press CHANNEL on the transmitter to search for another
frequency. Each time you press CHANNEL, the frequency
advances one channel up from CH 1 up to CH 13.
– press and hold CHANNEL for more than three seconds to make
sure the transmitter detects the best frequency automatically.
18
16-18RX-D702B[J].p65
18
05.8.25, 1:00 PM
2 Select the source to play
Basic operations
On the front panel:
Turn SOURCE SELECTOR until the source name
you want appears on the display.
The source lamp corresponding to the selected source lights in
red.
• As you turn SOURCE SELECTOR, the source changes as
follows:
ANALOG
AUTO SURR
L
TUNED STEREO
AUTO MUTING
R
S.WFR
MHz
2 2
1
3
DVR/DVD
VCR
DBS
TV (SIRIUS*)
USB WIRELESS
FM
AM
USB TERMINAL
(Back to the beginning)
AUX
Source lamps
DVR/DVD:
1
VCR:
DBS:
TV:
SIRIUS*:
USB WIRELESS:
2
3
1
2
3
4
5
6
7
8
9
10
0
10
USB TERMINAL:
FM:
AM:
AUX:
Select this for the DVD recorder or DVD
player.
Select this for the VCR.
Select this for the DBS tuner.
Select this for the TV.
Select this for the SIRIUS radio.
Select this for the PC component using
a wireless equipment.
Select this for the PC component.
Select this for an FM broadcast.
Select this for an AM broadcast.
Select this for the component connected
to the AUX jacks on the front panel
(inside the front door).
From the remote control:
Press one of the source selecting buttons.
• For “USB WIRELESS” and “USB TERMINAL,” press USB. Each
time you press USB, the mode alternates between “USB
WIRELESS” and “USB TERMINAL.”
• For “FM” and “AM,” press FM/AM. Each time you press FM/AM,
the mode alternates between “FM” and “AM.”
1 Turn on the power
Press
STANDBY/ON (or
remote control).
* Changing the source name
On the front panel ONLY:
Press SET when “TV” is selected as the source.
AUDIO on the
The standby lamp goes off and the source lamp of the current
source lights in red.
• “ASSIGN SIRIUS” appears on the display for a while.
ANALOG
Current source name appears.
AUTO SURR
L
R
S.WFR
ANALOG
AUTO SURR
L
TUNED STEREO
AUTO MUTING
R
S.WFR
MHz
To turn off the power (into standby)
Press
STANDBY/ON (or
AUDIO on the remote control)
again.
The standby lamp lights in red.
• When you change the source name to “TV,” press SET when
“SIRIUS” is selected as the source. “ASSIGN TV” appears on
the display for a while.
NOTE
When you change the source name to “SIRIUS,” you cannot
select “TV” as the source.
NOTES
• A small amount of power is consumed in standby mode. To turn
the power off completely, unplug the AC power cord.
• Turning a source component on before turning the receiver on
may cause a noise or interrupt the sound and picture. In this
case, turn both the source component and the receiver off, then
turn the receiver on before turning the source component on.
19
19-22RX-D702B[J]_f.p65
19
05.8.25, 1:00 PM
Selecting the video input setting
Select the proper video input setting according to the connection
method on pages 11 to 15.
From the remote control ONLY:
Press VIDEO INPUT to select the video input
setting.
NOTES
• “HDMI” is available only for the source with “HDMI” selected in
the video input setting (see the left column).
• “DIGITAL” is available for the source assigned for “DIGITAL IN
1,” “DIGITAL IN 2,” or “DIGITAL IN 3.” See page 31 for details.
Initial setting of VIDEO INPUT and AUDIO INPUT for
each source
• Each time you press the button, the input setting changes as
follows. This setting is memorized for each source.
L
C
Setting
VIDEO INPUT
AUDIO INPUT
DVR/DVD
HDMI
HDMI
VCR
HDMI
HDMI
DBS
S
Source
AUTO SURR
DIGITAL AUTO
R
S.WFR LFE
DIGITAL
LS
RS
HDMI
CMPNT (component)
S (S-video)
C (composite)
(Back to the beginning)
NOTES
• For “VCR” and “DBS,” you can select “HDMI” and “CMPNT” for
the source you assigned in “HDMI SELECT” and “CMPNT
SELECT” (see page 32).
• When the video input setting and the audio input setting are
both set to “HDMI,” changing the video input setting changes the
audio input setting to the appropriate setting.
Selecting the audio input setting
Select the proper audio input setting according to the connection
method (analog or digital) on pages 10 to 16.
• In case of digital connection using the terminals on the rear of
the receiver, you also need to select the correct digital input
terminal. (See “Setting the digital input (DIGITAL IN) terminals—
DIGITAL IN 1/2/3” on page 31.)
From the remote control ONLY:
Press AUDIO INPUT to select the audio input
setting.
L
C
SIRIUS
ANALOG (fixed)
DIGITAL (fixed)
USB TERMINAL
DIGITAL (fixed)
FM
ANALOG (fixed)
AM
ANALOG (fixed)
AUX
S
DIGITAL
3 Adjust the volume
To increase the volume, turn MASTER VOLUME
control clockwise (or press VOLUME + on the
remote control).
To decrease the volume, turn MASTER VOLUME
control counterclockwise (or press VOLUME – on
the remote control).
• When you adjust the volume, the volume level indication
appears on the display for a while.
ANALOG
AUTO SURR
L
R
S.WFR
CAUTION:
AUTO SURR
DIGITAL
ANALOG
USB WIRELESS
• Each time you press the button, the audio input setting changes
as follows. This setting is memorized for each source.
DIGITAL AUTO
DIGITAL
TV
R
S.WFR LFE
LS
RS
HDMI
DIGITAL
ANALOG
(Back
to
the
beginning)
A MULTI
Always set the volume to the minimum before starting any
sources. If the volume is set at its high level, the sudden blast of
sound energy can permanently damage your hearing and/or ruin
your speakers.
NOTE
HDMI (for “DVR/DVD,” “VCR” and “DBS”):
Select for the source with HDMI connection. The
receiver automatically detects the incoming
signal format, then the digital signal format
indicator (LINEAR PCM,
,
, or
96/24) for the detected signal lights up,
and the HDMI lamp on the front panel lights up.
DIGITAL*:
ANALOG*:
Select for the digital input setting. The receiver
automatically detects the incoming signal
format, then the digital signal format indicator
(LINEAR PCM,
,
, or
96/24)
for the detected signal lights up.
Select for the analog input setting. The ANALOG
indicator lights up on the display.
A MULTI (Only for “DVR/DVD”):
Select when connecting a DVD recorder or DVD
player to DVD MULTI IN jacks (see page 12).
The ANALOG indicator lights up on the display.
* When “TV” is selected as the source, only “DIGITAL” or
“ANALOG” appears on the display as the audio input setting.
The volume level can be adjusted within the range of “0” (minimum)
to “50” (maximum).
Listening with headphones
You can enjoy not only stereo software but also multi-channel
software through the headphones. (Sounds are down-mixed to the
front channels while playing multi-channel software.)
Connect a pair of headphones to the PHONES jack on the
front panel to activate the HEADPHONE mode.
The HEADPHONE indicator lights up on the display.
• You can also enjoy the Surround/DSP mode through the
headphones—3D HEADPHONE mode. For details, see page
43.
• Disconnecting a pair of headphones from the PHONES jack
cancels the HEADPHONE (or 3D HEADPHONE) mode and
activates the speakers.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume
can damage both the headphones and your hearing.
• Before removing headphones, as high volume may output from
the speakers.
20
19-22RX-D702B[J]_f.p65
20
05.8.25, 1:00 PM
Selecting the digital decode mode
Turning off the sounds temporarily
This receiver automatically detects the incoming digital signal
format when “HDMI” or “DIGITAL” is selected in the audio input
setting (see page 20). When “HDMI” or “DIGITAL” is selected, the
digital decode mode is set to “DGTL (Digital) AUTO,” and the
DIGITAL AUTO indicator lights up on the display.
If the following symptoms occur while playing Dolby Digital or DTS
software with “DGTL AUTO” selected, follow the procedure below:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching for or skipping chapters or
tracks.
From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers and headphones.
From the remote control ONLY:
To restore the sound, press MUTING again.
Press DECODE MODE to select “DOLBY
DIGITAL” or “DTS.”
• Each time you press DECODE MODE, the digital decode mode
changes as follows:
AUTO SURR
DIGITAL
L
DIGITAL
C
ANALOG
AUTO SURR
L
R
S.WFR
• Pressing VOLUME +/– (or turning MASTER VOLUME control
on the front panel) also restores the sound.
Changing the display brightness
R
You can dim the display—Dimmer.
S.WFR LFE
LS
RS
DGTL AUTO
DTS
“MUTING” appears on the display and the volume turns off.
DOLBY DIGITAL
(Back to the beginning)
• To play back software encoded with Dolby Digital, select
“DOLBY DIGITAL.”
• To play back software encoded with DTS, select “DTS.”
NOTE
“DOLBY DIGITAL” or “DTS” is automatically reset to “DGTL AUTO”
in the following cases:
– When you turn off the receiver.
– When you select another source.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1:
Dims the display slightly.
Dims the blue illumination slightly.
DIMMER 2:
Dims the display more than DIMMER 1.
Dims the blue illumination slightly (more than
DIMMER 1).
DIMMER 3:
Turns off the display and blue illumination.
(Temporarily canceled when you operate the
receiver.)
DIMMER OFF: Cancels the Dimmer (normal display).
The following digital signal format indicators on the display
indicate what type of signal comes into the receiver.
LINEAR PCM: Lights up when Linear PCM signal comes in.
• When the multi-channel PCM signal comes
in, “MULTI CH PCM” appears on the display
for a while.
:
Lights up when Dolby Digital signal comes in.
• Flashes when “DOLBY DIGITAL” is selected
for any software other than Dolby Digital.
:
Lights up when conventional DTS signal comes
in.
• Flashes when “DTS” is selected for any
software other than DTS.
96/24:
Lights up when DTS 96/24 signal comes in.
NOTE
When “DGTL AUTO” cannot recognize the incoming signal, no
digital signal format indicator lights up on the display.
21
19-22RX-D702B[J]_f.p65
21
05.8.25, 1:00 PM
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
SLEEP indicator
ANALOG
SLEEP
AUTO SURR
L
R
S.WFR
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Audio input setting (see page 20)
• Midnight mode (see page 31)
• Volume level for each source when One Touch Operation is
set to “ONE TOUCH OP: ON” (see page 32)
• Speaker output level (see page 36)
• Digital equalization pattern (see page 37)
• Bass boost (see page 37)
• Input attenuator mode (see page 37)
• Surround/DSP mode selection (see page 45)
10min 20min 30min 40min 50min 60min
OFF (canceled)
90min
80min
70min
NOTE
If the source is “FM” or “AM,” you can assign a different setting
for each band.
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly so that “SLEEP OFF” appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when you turn off the
receiver.
Making sounds natural
JVC’s CC (Compression Compensative) Converter eliminates
jitter and ripples, achieving a drastic reduction in digital distortion
by processing the digital music data in 24 bit-quantization and by
expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz
signals)/192 kHz (for fs 48 kHz signals) on the front speakers.
By using the CC Converter, you can obtain a natural sound field
from both digital and analog sources.
Press CC CONVERTER repeatedly.
• Each time you press the button, the mode changes as follows:
CC CNVRTR 1:
CC CNVRTR 2:
CC CNVRTR OFF:
Select when playing back an analog
source or a digital source with non
compressed digital sound signal (Linear
PCM).
The CC CONVERTER 1 indicator lights
up on the display.
Select when playing back a source with
compressed digital sound signal (Dolby
Digital or DTS).
The CC CONVERTER 2 indicator lights
up on the display.
Select when not using the CC Converter.
Signal and speaker indicators on the display
Signal indicators
L
C
Speaker indicators
R
L
S.WFR LFE
LS S RS
SB SB SB
ANALOG DUAL MONO AUTO SURR
DIGITAL AUTO L C R HEADPHONE
LINEAR PCM S.WFR LFE
PL x
DIGITAL
NEO : 6 DSP
LS S RS 3D-PHONIC
96 / 24
SB SB SB VIRTUAL SB
22
R
SB SB SB
The signal indicators light up as follows:
L:
• When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R:
• When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C:
Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes
in.
RS: Lights up when the right surround channel signal comes
in.
S:
Lights up when monaural surround signal comes in.
SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
NOTES
• When “A MULTI” is selected in the audio input setting (see
page 20), all the signal indicators except “SB,” “S,” and “LFE”
light up.
• When playing back multi-channel digital sound recorded in
DVD-Audio with HDMI connection (see pages 11 and 20),
the signal indicators may not light up correctly.
The speaker indicators light up as follows:
• The subwoofer indicator ( S.WFR ) lights up when
“SUBWOOFER” is set to “SUBWOOFER: YES.” For details,
see page 28.
• The other speaker indicators light up only when the
corresponding speaker is set to “SMALL” or “LARGE,” and
also when required for the current playback.
22
19-22RX-D702B[J]_f.p65
C
S.WFR LFE
LS S RS
05.8.25, 1:00 PM
From the remote control ONLY:
Basic settings
To obtain the best possible sound effect from Surround/DSP
modes (see pages 41 to 45), you need to set up the speaker and
subwoofer information after all the connections are completed.
From pages 23 to 32, how to set speakers and other basic items
of the receiver are explained.
1
2
3
4
5
6
7
8
9
10
0
10
1 Take your position where you listen to the
sound.
• Make sure speaker cables are connected firmly.
Setting the speaker information
automatically—Smart Surround Setup
The distance from your listening point to the speakers is one of
the important elements to obtain the best possible sound effect
from the Surround/DSP modes.
By using Smart Surround Setup, the following are automatically
calculated by one simple action—clapping hands.
• Speaker distance (compared to that of the closest speaker)
• Speaker output level (except the subwoofer)
2 Press and hold SMART S. SETUP until
“SETTING UP” flashes.
NOTES
• Before starting Smart Surround Setup, set the speaker
information correctly (SMALL, LARGE, or NO) according to your
speakers except the subwoofer (see page 28).
• When the setting is made by Smart Surround Setup, the
speaker distance and output level you have set before will be
inactive.
• You can see the setting process on the TV screen and the
display during Smart Surround Setup. If you have turned off the
display, cancel the Dimmer (see page 21); otherwise, you
cannot see the information on the display.
• Smart Surround Setup will not be done correctly if you or other
object blocks the sound.
• When you change your speakers, do the following procedure
again.
In this section, the on-screen display on the TV screen is used
for explaining.
• The on-screen display does not appear on the TV screen
when the video input setting (see page 20) is set to “HDMI.”
*3
*2
*1
SMART SURROUND SETUP
FL
C
FR
SL
*7
*6
*1
*2
*3
*4
*5
*6
*7
SETTING UP
SBL
FL :
C :
FR :
SR :
SBR:
SBL :
SL :
SR
SBR
*4
*5
Left front speaker
Center speaker
Right front speaker
Right surround speaker
Right surround back speaker
Left surround back speaker
Left surround speaker
3 When “CLAP YOUR HANDS.” appears, clap
your hands over your head once while the
indications still remain.
• On the display, “SETTING UP” stops flashing.
The receiver starts detecting the level of the sound coming
through each speaker (except the subwoofer).
CONTINUED ON THE NEXT PAGE
23
23-32RX-D702B[J]_f.p65
23
05.8.25, 1:01 PM
When your clapping sound is detected successfully
When your clapping sound is not detected correctly
• On the TV screen, “SUCCESSFUL,” “RESULT,” and the setting
values appear. The setting values are shown for about 10
seconds.
Ex.:
*8
“SETTING UP” appears again after one of the following
messages. In this case, repeat step 3.
SMART SURROUND SETUP
FL+2
C 0
FR+2
+0.3m
*10
STD
+0.3m
SL
SUCCESSFUL
SR
+2
+2
+0.5m
RESULT
+0.5m
+0.6m
+0.6m
+4
+4
SBL
SBR
*9
• On the display, “SUCCESSFUL” appears, then the setting
values are shown as follows for about 10 seconds:
Ex.:
*8
SILENT:
• The receiver detects sound from only the left
and right front speakers.
• The receiver detects no sound from the front
speakers and detects sound from at least one of
the other speakers.
SILENT-ALL: The receiver cannot detect any sound from any
speaker for about 10 seconds.
AGAIN:
• The receiver cannot detect sound from the left
or right front speaker.
• The receiver fails to calculate the speakers'
output level and difference of each speaker's
position in distance.
In the following cases, set the speakers manually.
• When “SILENT” appears twice in succession
The setting is partially made. (The distance of the speakers
from which sound has not been detected is set to “+9.0m
(+30ft).”)
The receiver exits from Smart Surround Setup.
• When “MANUAL” appears
*9
FL
C
SBR
FR
SBL
*10
SR
SL
*8
Standard channel (the closest speaker).
This speaker position now works as the reference
position (“0m/ft”) and other speakers’ distance is
shown by the difference with this reference speaker
position.
*9
Difference of each speaker position in distance (in
meters or feet).
*10 Each speaker’s output level (–6 to +6).
When finishing displaying the setting values
On the TV screen, “COMPLETED” appears, then “TEST TONE”
and “END” appear. On the display, “TEST? END?” appears.
• To adjust the speakers’ output levels manually, press TEST (see
page 36).
• To erase the on-screen display, press SET or any button except
TEST.
• The receiver returns to normal operation mode automatically if
no operations are done for about 10 seconds.
Ex.:
SMART SURROUND SETUP
FL+2
C 0
FR+2
+0.3m
SL
+6
+0.5m
STD
+0.3m
TESTTONE
SR
END
+2
+0.5m
+0.6m
+4
SBL
+0.6m
+4
SBR
The receiver fails to detect the sound three times. The receiver
exits from Smart Surround Setup.
To cancel Smart Surround Setup, press EXIT while “SETTING
UP” flashes.
• No other operations can be accepted after “SETTING UP” stops
flashing. Complete the Smart Surround Setup.
To check the current setting made by Smart Surround Setup,
press SMART S. SETUP while the receiver is in normal operation
mode.
The setting values appear. On the display, the setting values are
shown one after another.
• The current setting is not indicated but “MANUAL” appears if you
change the following settings after using Smart Surround Setup:
– If you change speaker distance manually.
– If you change one of the speaker sizes either from “NO” to
“SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO.”
To check the current setting, see each setting item of the
speaker distance (see page 29) and the speaker output level
(see page 36).
• If you have not used Smart Surround Setup, “NO S.S.S.”
appears.
NOTES
• When Smart Surround Setup does not work properly, try
measures below:
– set the volume to “0.”
– turn off the components (TV, DVD player, DVD recorder, or
subwoofer, for example) near this receiver or the speakers.
• The speaker distance and output level manually set will be
applied instead of those set by using Smart Surround Setup in
the following cases:
– When you change one of the speaker distances (see page
29).
– When you change one of the speaker sizes either from “NO”
to “SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO”
(see page 28).
• When you want to adjust the speaker distance and output level
manually, see pages 29 and 36.
• When the headphone is in use, the receiver returns to normal
operation mode without showing “TEST TONE.”
• The speakers which are set to “NO” in the speaker setting (see
page 28) are not indicated clearly on the TV screen.
• Do not clap your hands so hard that it may hurt your hands.
24
23-32RX-D702B[J]_f.p65
24
05.8.25, 6:58 PM
Basic setting items
You can adjust the following items. See pages in parentheses for
details.
• You cannot select the items which is not available with the
current setting. For example, when “S BACK SPK” is set to “S
BACK SPK: NO,” you cannot select the following items:
S BACK OUT, SB SPK DIST., SBL SPK DIST., SBR SPK DIST.
• The name of the item shown below is the on-screen display
indication and the name in parentheses is the display indication.
Items
To do
SUBWOOFER
(SUBWOOFER)
Register your subwoofer. (28)
Items
To do
CMPNT SELECT Select the source for COMPONENT VCR
(CMPNT SELECT) (DBS) in jacks. (32)
VIDEO OUTPUT Select the output video signal according to
(VIDEO OUTPUT) the connection method for a TV. (32)
SUPERIMPOSE
Select to superimpose the menus on the
(SUPERIMPOSE) TV screen. (32)
* If you have used Smart Surround Setup on pages 23 and 24,
these settings are not required.
NOTE
FRONT SPK
(FRONT SPK)
Register your front speaker size. (28)
CENTER SPK
(CENTER SPK)
Register your center speaker size. (28)
SURR SPK
Register your surround speaker size. (28)
(SURROUND SPK)
Some items are not available when multi channel PCM (see page
42) signals recorded in DVD-Audio are coming. See page 12 for
details.
Operation through on-screen display
menus
S BACK SPK
(S BACK SPK)
Register your surround back speaker size. (28)
S BACK OUT
(S BACK OUT)
Register the number of your surround back
speaker(s). (29)
DISTANCE UNIT
(DIST UNIT)
Select the measuring unit for the speaker
distance. (29)
Menu operation buttons
FL SPK DIST.*
(FRONT L DIST)
Register the distance from the left front
speaker to your listening point. (29)
On the front panel:
FR SPK DIST.*
(FRONT R DIST)
Register the distance from the right front
speaker to your listening point. (29)
C SPK DIST.*
(CENTER DIST)
Register the distance from the center speaker
to your listening point. (29)
SL SPK DIST.*
(SURR L DIST)
Register the distance from the left surround
speaker to your listening point. (29)
SR SPK DIST.*
(SURR R DIST)
Register the distance from the right surround
speaker to your listening point. (29)
SBL SPK DIST.* Register the distance from the left surround
(S BACK L DIST) back speaker to your listening point. (29)
You can make adjustments to the basic settings easily by using
the on-screen display menus.
Button / JOG
SET button
move to the selected menu or return to the
previous SETTING MENU.
MULTI JOG
• select a menu or an item.
• change a setting.
SBR SPK DIST.* Register the distance from the right surround
(S BACK R DIST) back speaker to your listening point. (29)
SB SPK DIST.*
(S BACK DIST)
Register the distance from the surround back
speaker to your listening point. (29)
EX/ES/PLIIx
(EX/ES/PLIIx)
Select the EX/ES/PLIIx reproduction mode. (30)
DUAL MONO
(DUAL MONO)
Select the Dual Mono sound channel. (30)
SUBWFR OUT
(SUBWOOFER OUT)
Select sounds emitted from the subwoofer. (30)
CROSSOVER
(CROSSOVER)
Select the cutoff frequency to the subwoofer. (31)
LFE ATT
(LFE ATT)
Attenuate the bass (LFE) sounds. (31)
MIDNIGHT
(MIDNIGHT MODE)
Reproduce a powerful sound at night. (31)
DIGITAL IN 1
(DIGITAL IN 1)
Select the component connected to the digital
coaxial terminal—1(DVR/DVD). (31)
DIGITAL IN 2
(DIGITAL IN 2)
Select the component connected to the digital
optical terminal—2(DBS). (31)
DIGITAL IN 3
(DIGITAL IN 3)
Select the component connected to the digital
optical terminal—3(VCR). (31)
AUDIO DELAY
(AUDIO DELAY)
Set the audio delay time to correct
synchronization between video and audio
signals. (31)
To do
SETTING button show setting item previously selected.
From the remote control:
Button
To do
SETTING button show setting item previously selected.
5 / ∞ buttons
select a menu or an item.
SET button
move to the selected menu or return to the
previous SETTING MENU.
EXIT button
exit from the SETTING MENU.
2 / 3 buttons
change a setting.
ONE TOUCH OP Memorize the volume level for each source.
(ONE TOUCH OP) (32)
HDMI SELECT
(HDMI SELECT)
Select the source for HDMI VCR (DBS) in
terminal. (32)
CONTINUED ON THE NEXT PAGE
25
23-32RX-D702B[J]_f.p65
25
05.8.25, 1:01 PM
Setup menu configuration
• Items on the menus shown below are all set to the initial values when shipped from the factory.
• Some of the menus or some items on the menu cannot be shown or cannot be adjusted depending on the current settings and the
connections. (For details, see the respective explanations in this section.)
SETTING MENU (5)
Press SET
SETTING MENU (1)
SETTING MENU (1)
5
SUBWOOFER
:
NO
FRONT
SPK
: LARGE
CENTER
SPK
: SMALL
SURR
SPK
: SMALL
S BACK
SPK
: SMALL
S BACK
OUT
:
2SPK
∞
:ENTER
:EXIT
SETTING MENU (2)
SETTING MENU (2)
5
DISTANCE UNIT : meter
FL
SPK DIST.
:
3.0m
FR
SPK DIST.
:
3.0m
C
SPK DIST.
:
3.0m
SL
SPK DIST.
:
3.0m
SR
SPK DIST.
:
3.0m
SBL SPK DIST.
:
3.0m
SBR SPK DIST.
:
3.0m
∞
:ENTER
:EXIT
SETTING MENU (3)
SETTING MENU (3)
5
EX/ES/PLIIx :
AUTO
DUAL MONO
:
MAIN
SUBWFR OUT :
LFE
CROSSOVER
:
100Hz
LFE ATT
:
0dB
MIDNIGHT
:
OFF
∞
:ENTER
:EXIT
SUBWOOFER
See page 28
FRONT SPEAKER
See page 28
CENTER SPEAKER
See page 28
SURROUND SPEAKER
See page 28
SURROUND BACK SPEAKER
See page 28
SURROUND BACK OUT
See page 29
DISTANCE UNIT
See page 29
FL
SPK DISTANCE
See page 29
FR
SPK DISTANCE
See page 29
CENTER SPK DISTANCE
See page 29
SL
SPK DISTANCE
See page 29
SR
SPK DISTANCE
See page 29
SBL SPK DISTANCE
See page 29
SBR SPK DISTANCE
See page 29
EX/ES/PLIIx
See page 30
DUAL MONO
See page 30
SUBWOOFER OUT
See page 30
CROSSOVER
See page 31
LFE ATT
See page 31
MIDNIGHT MODE
See page 31
DIGITAL IN 1
See page 31
DIGITAL IN 2
See page 31
DIGITAL IN 3
See page 31
AUDIO DELAY
See page 31
ONE TOUCH OPERATION
See page 32
HDMI SELECT
See page 32
COMPONENT SELECT
See page 32
VIDEO OUTPUT
See page 32
SUPERIMPOSE
See page 32
SETTING MENU (4)
SETTING MENU
5
DIGITAL IN 1
DIGITAL IN 2
DIGITAL IN 3
AUDIO DELAY
ONE TOUCH OP
∞
(4)
: DVR/DVD
:
DBS
:
VCR
:
OFF
:
OFF
:EXIT
:ENTER
SETTING MENU (5)
SETTING MENU
5
HDMI
SELECT
CMPNT SELECT
VIDEO OUTPUT
SUPERIMPOSE
∞
:ENTER
(5)
:
:
:
:
VCR
VCR
HDMI
ON
:EXIT
SETTING MENU (1)
26
23-32RX-D702B[J]_f.p65
26
05.8.25, 1:01 PM
Menu operating procedure
When operating, the on-screen display appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32).
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
In this section, the operation of the remote control is used for explaining.
Ex.: When setting DIGITAL IN 1 terminal.
Operations
On the TV screen
1 To start the setting, press SETTING.
On the display
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
x
ATT
HP
MHz
kHz
SETTING MENU (1)
5
SUBWOOFER
:
NO
FRONT
SPK
: LARGE
CENTER
SPK
: SMALL
SURR
SPK
: SMALL
S BACK
SPK
: SMALL
S BACK
OUT
:
2SPK
The setting item previously selected can be shown
on the TV screen by pressing SETTING on the front
panel when the receiver is in normal operation
mode.
∞
:ENTER
The submenu previously
selected appears.
:EXIT
The setting item previously selected
appears.
2 To select the desired submenu, press
5 or ∞ repeatedly.
There are five screens from “SETTING MENU (1)”
to “SETTING MENU (5).” To change the screen,
simply pressing 5 or ∞ repeatedly. You can go to
the next/previous screen.
• On the front panel, turn MULTI JOG.
Button indications on the screen
The buttons for operating the menu are shown on the TV screen. You can operate the menu with these buttons.
SETTING MENU (1)
5
SUBWOOFER
:
NO
FRONT
SPK
: LARGE
CENTER
SPK
: SMALL
SURR
SPK
: SMALL
S BACK
SPK
: SMALL
S BACK
OUT
:
2SPK
∞
:ENTER
:EXIT
Usable buttons and their functions
DIGITAL IN 1
DIGITAL IN 1 :2DVR/DVD3
23:OPERATE
:BACK
Usable buttons and their functions
CONTINUED ON THE NEXT PAGE
27
23-32RX-D702B[J]_f.p65
27
05.8.25, 1:01 PM
3 Press SET.
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
x
ATT
HP
MHz
kHz
DIGITAL IN 1
DIGITAL IN 1 :2DVR/DVD3
23:OPERATE
The current setting of the
selected item appears.
:BACK
The selected submenu appears.
4 To select the appropriate setting, press
2 or 3 repeatedly, then press SET.
The on-screen display returns to the previous
SETTING MENU. In this example, “SETTING MENU
(4)” appears on the TV screen and “DIGITAL IN 1”
appears on the display.
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
x
ATT
HP
MHz
kHz
DIGITAL IN 1
DIGITAL IN 1 :2DVR/DVD3
DVR/DVD
TV
• On the front panel, turn MULTI JOG, then press
SET.
DBS
VCR
5 Repeat steps 2 to 4 to set other items
if necessary.
NOTE
To exit from menu operations, press EXIT on the remote control. On the front panel, press SETTING.
Setting the items
When performing the basic settings viewing the indications on the display, the indications are slightly different from what is shown
on the on-screen display.
This is because of the limited number of characters shown on the display.
Ex.: • “SUBWOOFER: YES” is shown as “SUBWFR <YES>” on the display.
• “CROSSOVER: 100Hz” is shown as “CROSS <100Hz>” on the display.
Setting the speakers
To obtain the best possible surround effect from the Surround and
DSP modes, register the setting about the speaker after all
connections are completed.
7 Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker), SURR
SPK (surround speakers), S BACK SPK (surround
back speakers)
7 Setting subwoofer information—SUBWOOFER
Register the sizes of all the connected speakers.
Select whether you have connected a subwoofer or not.
LARGE
Select when the cone speaker size is larger
than 12 cm (4 3/4 inches).
SMALL
Select when the cone speaker size is smaller
than 12 cm (4 3/4 inches).
NO
Select when you have disconnected a speaker.
(Not selectable for the front speakers.)
SUBWOOFER: YES
SUBWOOFER: NO
Select when you have connected a
subwoofer.
The subwoofer indicator ( S.WFR ) lights up
on the display. You can adjust the
subwoofer output level (see page 36).
Select when you have disconnected a
subwoofer. Selecting this changes the
front speaker size to “LARGE” (see the
right column).
Initial setting: LARGE (for the front speakers)
SMALL (for other speakers)
Initial setting: SUBWOOFER: NO
28
23-32RX-D702B[J]_f.p65
28
05.8.25, 1:01 PM
7 Setting the surround back speaker(s)
—S BACK OUT
C
FL
Register the number of the surround back speaker(s).
S BACK OUT: 1SPK
Select when you use 1 surround back
speaker.
S BACK OUT: 2SPK
Select when you use 2 surround back
speakers.
FR
3.3 m
(11 ft)
3.0 m
(10 ft)
2.7 m
(9 ft)
2.4 m
(8 ft)
2.1 m
(7 ft)
Initial setting: S BACK OUT: 2SPK
SL
SR
NOTES
• If you have selected “SMALL” for the front speaker size, you
cannot select “LARGE” for other speakers.
• When “SUBWOOFER” is set to “SUBWOOFER: NO,” the front
speaker size is fixed to “LARGE” (and you cannot select
“SMALL”).
• When “SURR SPK” is set to “SMALL,” you cannot select
“LARGE” for the surround back speaker.
• When “SURR SPK” is set to “NO,” the surround back speaker is
fixed to “NO.”
• When “S BACK SPK” is set to “NO,” you cannot select “S BACK
OUT.”
• When “S BACK OUT” is set to “S BACK OUT: 1SPK,” connect
the surround back speaker to the left surround back speaker
terminal (see page 8). No sound comes from the surround back
speaker if you connect it to the right surround back speaker
terminal.
7 Setting the speaker distance
The distance from your listening point to the speakers is one of
the important elements to obtain the best possible sound effect
from the Surround/DSP modes.
By referring to the speaker distance, the receiver automatically
sets the delay time of the sound through each speaker so that
sounds through all the speakers can reach you at the same time.
SBL
SBR
In this case, set the distance as follows:
Left front speaker (FL):
“FL SPK DIST.: 3.0m (10ft)”
Right front speaker (FR):
“FR SPK DIST.: 3.0m (10ft)”
Center speaker (C):
“C SPK DIST.: 3.0m (10ft)”
Left surround speaker (SL):
“SL SPK DIST.: 2.7m (9ft)”
Right surround speaker (SR):
“SR SPK DIST.: 2.7m (9ft)”
Left surround back speaker (SBL): “SBL SPK DIST.: 2.4m (8ft)”
Right surround back speaker (SBR): “SBR SPK DIST.: 2.4m (8ft)”
NOTES
• You cannot set the speaker distance for the speakers you have
set to “NO.”
• If you have selected “S BACK OUT: 1SPK” for “S BACK OUT”
(see the left column), “SB SPK DIST.” appears instead of “SBL
SPK DIST.” and “SBR SPK DIST..”
7 Measuring unit—DISTANCE UNIT
Select which measuring unit you use.
DISTANCE UNIT: meter Select to set the distance in meters.
DISTANCE UNIT: feet
Select to set the distance in feet.
Initial setting: DISTANCE UNIT: meter
7 Speaker distance—
FL SPK DIST. (for the left front speaker),
FR SPK DIST. (for the right front speaker),
C SPK DIST. (for the center speaker),
SL SPK DIST. (for the left surround speaker),
SR SPK DIST. (for the right surround speaker),
SBL SPK DIST. (for the left surround back speaker),
SBR SPK DIST. (for the right surround back speaker)
Adjustable range: 0.3 m to 9.0 m in 0.3 m intervals
(1 ft to 30 ft in 1 ft intervals)
Initial setting: 3.0 m (10 ft) for all speakers
29
23-32RX-D702B[J]_f.p65
29
05.8.25, 1:01 PM
Activating the EX/ES/PLIIx setting—EX/ES/
PLIIx
Selecting the main or sub channel
—DUAL MONO
Depending on this setting, available Surround modes for digital
multi-channel software vary—EX/ES/PLIIx reproduction or 5.1channel reproduction. Select an appropriate setting for your
enjoyment.
• For details about relation between EX/ES/PLIIx setting and
available Surround mode, see page 44.
• To activate the Surround mode, see page 45.
You can select the playback sound (channel) you want while
playing digital software recorded (or broadcasted) in Dual Mono
mode (see page 42), which includes two monaural channels
separately. When the receiver detects Dual mono signals, the
DUAL MONO indicator lights up on the display.
EX/ES/PLIIx: AUTO
According to the incoming signal, an appropriate
Surround mode is applied.
• For Dolby Digital Surround EX and DTS-ES
software, 7.1-channel reproduction is applied*.
• For the other multi-channel (more than 4
channel) encoded software, 5.1-channel
reproduction is applied.
DUAL MONO: MAIN Select to play back the main channel (Ch 1).*
Signal indicator “L” lights up while playing
back this channel.
DUAL MONO: SUB Select to play back the sub-channel (Ch 2).*
Signal indicator “R” lights up while playing
back this channel.
DUAL MONO: ALL
EX/ES/PLIIx: ON
Select to apply 7.1-channel reproduction to both
5.1-channel and 6.1-channel encoded software.
EX/ES/PLIIx: PLIIx MOVIE
Select to apply PLIIx MOVIE reproduction to
both 5.1-channel and 6.1-channel encoded
software.
EX/ES/PLIIx: PLIIx MUSIC
Select to apply PLIIx MUSIC reproduction to
both 5.1-channel and 6.1-channel encoded
software.
EX/ES/PLIIx: OFF
Select to cancel the EX/ES/PLIIx reproduction.
Initial setting: EX/ES/PLIIx: AUTO
* For some Dolby Digital Surround EX software, Dolby Digital 5.1channel reproduction (“DOLBY DIGITAL”) may be applied even
though you have selected “AUTO”. In this case, select “ON” to
apply “DOLBY D EX.” (See page 44.)
Select to play back both the main and subchannels (Ch 1/Ch 2).*
Signal indicators “L” and “R” light up while
playing back these channels.
Initial setting: DUAL MONO: MAIN
* Dual Mono signals can be heard from the following speakers—L
(left front speaker), R (right front speaker), and C (center
speaker), with respect to the current Surround setting:
With Surround Activated
Dual Mono
setting
Without
Surround
Center speaker setting
SML/LRG
L
R
MAIN
Ch 1
Ch 1
L
Ch 1
C
ALL
Ch 1
Ch 2
Ch 1+Ch 2
SUB
Ch 2
Ch 2
Ch 2
NO
R
L
R
Ch 1
Ch1
Ch 1+Ch 2 Ch 1+Ch 2
Ch 2
Ch 2
NOTE
The Dual Mono format is not identical with bilingual broadcasting
for TV programs. So this setting does not take effect while
watching such bilingual programs.
Setting bass sound
NOTES
• This function is not available when “SURR SPK” is set to “NO”
(see page 28).
• When “S BACK SPK” is set to “NO” (see page 28), the Virtual
Surround Back (see page 44) is applied for EX/ES/PLIIx
reproduction and the VIRTUAL SB indicator lights up on the
display.
7 Setting subwoofer output—SUBWFR OUT
The subwoofer emits the LFE signals* and the bass elements of
each speaker set to “SMALL.”
You can make the bass elements of the front speaker channels
(MAIN) emitted through the subwoofer.
SUBWFR OUT: LFE
Select to emit the LFE signals and
the bass elements of each speaker
set to “SML.”
SUBWFR OUT: LFE+MAIN
Select to emit the bass elements of
the front speakers’ channels (MAIN)
when no bass elements are emitted
through the subwoofer in “SW: LFE.”
Initial setting: SUBWFR OUT: LFE
NOTE
When “SUBWOOFER” is set to “SUBWOOFER: NO” (see page
28), this function is not available.
* The LFE signals are emitted only when playing the following
software with the LFE signals:
– Dolby Digital multi channel software
– DTS multi channel software
When playing analog source or linear PCM software, no LFE
signals are emitted.
30
23-32RX-D702B[J]_f.p65
30
05.8.25, 1:01 PM
7 Setting the crossover frequency—CROSSOVER
Small speakers cannot reproduce the bass sounds efficiently. If
you use a small speaker in any position, this receiver
automatically reallocates the bass sound elements assigned to
the small speaker to the large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers (see page 28),
this function will not take effect (“CROSS OFF” appears).
CROSSOVER: 80Hz
Select when the cone speaker unit built in
the speaker is about 12 cm (4 3/4 inches).
CROSSOVER: 100Hz Select when the cone speaker unit built in
the speaker is about 10 cm (3 15/16 inches).
CROSSOVER: 120Hz Select when the cone speaker unit built in
the speaker is about 8 cm (3 3/16 inches).
Initial setting: CROSSOVER: 100Hz
NOTE
Crossover frequency is not valid for the HEADPHONE and 3D
HEADPHONE modes.
7 Setting the low frequency effect attenuator
—LFE ATT
If the bass sound is distorted while playing back software
encoded with Dolby Digital or DTS, set the LFE level to eliminate
distortion.
• This function takes effect only when the LFE signals come in.
LFE ATT: 0dB
Normally select this.
LFE ATT: –10dB
Select when the bass sound is distorted.
Setting the digital input (DIGITAL IN)
terminals—DIGITAL IN 1/2/3
When you use the digital input terminals, register what
components are connected to which terminals—DIGITAL IN 1/2/3
(see page 16) so that the correct source name will appear when
you select the digital source.
Select one of the following components for each terminal:
DVR/DVD For the DVD player (or DVD recorder).
DBS
For the DBS tuner.
VCR
For the VCR.
TV
For the TV.
Initial setting: For “DIGITAL IN 1”: DVR/DVD
For “DIGITAL IN 2”: DBS
For “DIGITAL IN 3”: VCR
NOTES
• You cannot assign the same component for different terminals.
The priority order for assignment is as follows:
“DIGITAL IN 1” > “DIGITAL IN 2” > “DIGITAL IN 3.”
Ex.: When “DIGITAL IN 1” is set to “DVR/DVD.”
DIGITAL IN 1 DVR/DVD
DBS
VCR
TV
For “DIGITAL IN 2,” “DBS,” “VCR,” and “TV” are selectable.
• In this case, “VCR” is selected.
DIGITAL IN 2 DVR/DVD
DBS
VCR
TV
For “DIGITAL IN 3,” “DBS” and “TV” are selectable.
Initial setting: LFE ATT: 0dB
DIGITAL IN 3 DVR/DVD
Using the Midnight mode—MIDNIGHT
You can enjoy a powerful sound at night using the Midnight mode.
When the Midnight mode is activated, the MIDNIGHT indicator
lights up on the display.
MIDNIGHT: OFF
MIDNIGHT: 1
MIDNIGHT: 2
Select when you want to enjoy surround
with its full dynamic range. (No effect
applied.)
Select when you want to reduce the
dynamic range a little.
Select when you want to apply the
compression effect fully (useful at night).
Initial setting: MIDNIGHT: OFF
DBS
: Selectable
VCR
TV
: Not selectable
• Setting “DIGITAL IN 1” affects “DIGITAL IN 2” and “DIGITAL IN
3” settings. When you have changed “DIGITAL IN 1,” confirm the
components assigned to “DIGITAL IN 2” and “DIGITAL IN 3.”
Setting the Audio delay level
—AUDIO DELAY
Synchronization between audio and video reproduction can be
possibly disturbed because video signal decoding is timeconsuming compared to the audio signal decoding.
On this setting, you can correct synchronization between video
and audio signals by delaying the audio signal timing.
Adjustable range: OFF and 10 ms to 100 ms (in 10 ms intervals)
From the remote control:
Initial setting: AUDIO DELAY: OFF
Press MIDNIGHT repeatedly to select either one of the
above.
1
2
3
4
5
6
7
8
9
10
0
10
31
23-32RX-D702B[J]_f.p65
31
05.8.25, 1:01 PM
Memorizing the volume level for each
source—ONE TOUCH OP
Selecting the output video signals
—VIDEO OUTPUT
This receiver memorizes some settings separately for each
source. In addition, you can store the volume level for each source
with the other memorized settings. (See page 22.)
• This receiver memorizes the volume level
– when you turn off the power, and
– when you change the source.
To use the video conversion function (see page 9), you need to
select this setting according to the connection method for a TV.
VIDEO OUTPUT: HDMI
Select this when connecting a TV with the HDMI cable.
VIDEO OUTPUT: CMPNT
ONE TOUCH OP: ON
Select to store the volume level separately for each
source. (The ONE TOUCH OPERATION indicator lights
up on the display.)
ONE TOUCH OP: OFF
Select this not to store the volume level.
Select this when connecting a TV with the component
video cable.
VIDEO OUTPUT: S
Select this when connecting a TV with the S-video cable.
VIDEO OUTPUT: C
Select this when connecting a TV with the composite
video cable.
Initial setting: ONE TOUCH OP: OFF
To recall the volume level
With the ONE TOUCH OPERATION indicator lit, the volume level
for the currently selected source is recalled when the source is
selected.
To cancel the One Touch Operation
Set One Touch Operation to “ONE TOUCH OP: OFF” so that the
ONE TOUCH OPERATION indicator goes off from the display.
Selecting the source for HDMI terminal and
COMPONENT VIDEO jacks—HDMI SELECT/
CMPNT SELECT
When you connect a VCR or a DBS tuner to the VCR (DBS) IN
terminal (jacks) in HDMI terminal or COMPONENT VIDEO jacks
on the rear of the receiver, you need to select either “VCR” or
“DBS” according to the component you connect.
If you have not selected appropriate source, you cannot view the
playback picture on the TV.
For the HDMI terminal:
HDMI SELECT: VCR
Select this when assigning the HDMI terminal for
a VCR.
HDMI SELECT: DBS
Select this when assigning the HDMI terminal for
a DBS tuner.
Initial setting: HDMI SELECT: VCR
For the COMPONENT VIDEO jacks:
Initial setting: VIDEO OUTPUT: HDMI
NOTE
To transmit the video signals selected in this setting, you need to
connect a TV and this receiver with the cable which can transmit
the selected video signals.
Superimposing the menus
—SUPERIMPOSE
You can select whether or not to superimpose the on-screen
display on the TV screen.
SUPERIMPOSE: ON
Select to superimpose the on-screen display on the TV
screen.
SUPERIMPOSE: OFF
Select to cancel superimposition. The on-screen display will
be shown on the blue background screen.
Initial setting: SUPERIMPOSE: ON
NOTES
• Some on-screen displays appear on the TV screen regardless
of this setting.
• When the video input setting (see page 20) is set to “CMPNT,”
the on-screen display will be shown on the blue background
screen even though “SUPERIMPOSE” is set to
“SUPERIMPOSE: ON.”
• The on-screen display does not appear on the TV screen when
the video input setting (see page 20) is set to “HDMI.”
CMPNT SELECT: VCR
Select this when assigning the COMPONENT
VIDEO jacks for a VCR.
CMPNT SELECT: DBS
Select this when assigning the COMPONENT
VIDEO jacks for a DBS tuner.
Initial setting: CMPNT SELECT: VCR
32
23-32RX-D702B[J]_f.p65
32
05.8.25, 1:01 PM
Sound adjustments
You can make sound adjustment to your preference after
completing basic setting.
Basic adjustment items
You can adjust the following items. See pages in parentheses for
details.
• You cannot select the items which is not available with the
current setting.
• The name of the item shown below is the on-screen display
indication and the name in parentheses is the display indication.
Items
To do
SUBWOOFER LEVEL*1 Adjust the subwoofer output level. (36)
(SUBWFR LVL)
FRONT L LEVEL*1*2 Adjust the left front speaker output level.
(FRONT L LVL)
(36)
FRONT R LEVEL*1*2 Adjust the right front speaker output level.
(FRONT R LVL)
(36)
CENTER LEVEL*1*2
(CENTER LVL)
Items
To do
DIMENSION
(DIMENSION)
Adjust sound localization pattern. (38)
CENTER GAIN
(CENTER GAIN)
Adjust the sound localization of the center
channel. (38)
CENTER TONE*1
(CENTER TONE)
Make the center tone soft or sharp. (38)
CNTR ALIGNMENT
(CENTER ALIGN)
Align the vertical localization of the center
channel signals. (38)
*1 You can adjust these items directly from the remote control.
*2 If you have used Smart Surround Setup on pages 23 and 24,
these settings are not required.
NOTE
Some items are not available when multi channel PCM (see page
42) signals recorded in DVD-Audio are coming. See page 12 for
details.
Operation through on-screen display
menus
You can make adjustments to the basic settings easily by using
the on-screen display menus.
Menu operation buttons
On the front panel:
Adjust the center speaker output level. (36)
SURR L LEVEL*1*2 Adjust the left surround speaker output level.
(SURR L LVL)
(36)
SURR R LEVEL*1*2 Adjust the right surround speaker output
(SURR R LVL)
level. (36)
S BACK L LEVEL*1*2 Adjust the left surround back speaker output
(S BACK L LVL)
level. (36)
1 2
S BACK R LEVEL* *
(S BACK R LVL)
Adjust the right surround back speaker
output level. (36)
S BACK LEVEL*1*2 Adjust the surround back speaker output
(S BACK LVL)
level. (36)
DIGITAL EQ 63Hz (D EQ 63Hz)*1
DIGITAL EQ 250Hz (D EQ 250Hz)*1
DIGITAL EQ 1kHz (D EQ 1kHz)*1
DIGITAL EQ 4kHz (D EQ 4kHz)*1
DIGITAL EQ 16kHz (D EQ 16kHz)*1
Adjust the equalization pattern of each
band. (37)
Button / JOG
To do
ADJUST button
show adjustment item previously selected.
SET button
move to the selected menu or return to the
previous ADJUST MENU.
MULTI JOG
• select a menu or an item.
• change a setting.
From the remote control:
BASS BOOST
(BASS BOOST)
Boost the bass level. (37)
INPUT ATT
(INPUT ATT)
Attenuate the input level of analog source.
(37)
EFFECT*1
(EFFECT)
Adjust the effect level. (37)
ROOM SIZE
(ROOM SIZE)
Select the room size for your virtual listening
room. (37)
LIVENESS
(LIVENESS)
Select the liveness level for your virtual
listening room. (38)
EXIT button
exit from the ADJUST MENU.
PANORAMA
(PANORAMA)
Add “wraparound” sound effect with sidewall image. (38)
2 / 3 buttons
change a setting.
CENTER WIDTH
(CENTER WIDTH)
Adjust the center channel localization
between the center speaker and the left/
right speakers. (38)
Button
To do
ADJUST button
show adjustment item previously selected.
5 / ∞ buttons
select a menu or an item.
SET button
move to the selected menu or return to the
previous ADJUST MENU.
CONTINUED ON THE NEXT PAGE
33
33-38RX-D702B[J]_f.p65
33
05.8.25, 1:14 PM
Setup menu configuration
• Items on the menus shown below are all set to the initial values when shipped from the factory.
• Some of the menus or some items on the menu cannot be shown or cannot be adjusted depending on the current settings and the
connections. (For details, see the respective explanations in this section.)
• The “ADJUST MENU (2),” “ADJUST MENU (3),” and “ADJUST MENU (4)” screen cannot be shown depending on the current settings
and the connections.
ADJUST MENU (4)
Press SET
ADJUST MENU (1)
ADJUST MENU (1)
5
SUBWOOFER
LEVEL :
0
FRONT
L
LEVEL :
0
FRONT
R
LEVEL :
0
CENTER
LEVEL :
0
SURR
L
LEVEL :
0
SURR
R
LEVEL :
0
S BACK L
LEVEL :
0
S BACK R
LEVEL :
0
∞
:ENTER
:EXIT
SUBWOOFER
LEVEL
See page 36
FRONT
L
LEVEL
See page 36
FRONT
R
LEVEL
See page 36
LEVEL
See page 36
CENTER
SURR
L
LEVEL
See page 36
SURR
R
LEVEL
See page 36
S BACK L
LEVEL
See page 36
S BACK R
LEVEL
See page 36
63Hz
See page 37
DIGITAL EQ 250Hz
See page 37
DIGITAL EQ
1kHz
See page 37
DIGITAL EQ
4kHz
See page 37
DIGITAL EQ 16kHz
See page 37
BASS BOOST
See page 37
INPUT ATT
See page 37
EFFECT
See page 37
ROOM SIZE
See page 37
LIVENESS
See page 38
PANORAMA
See page 38
CENTER WIDTH
See page 38
DIMENSION
See page 38
CENTER GAIN
See page 38
CENTER TONE
See page 38
CNTR ALIGNMENT
See page 38
ADJUST MENU (2)
ADJUST MENU (2)
5
DIGITAL EQ
63Hz
DIGITAL EQ 250Hz
DIGITAL EQ
1kHz
DIGITAL EQ
4kHz
DIGITAL EQ 16kHz
BASS BOOST
∞
:ENTER
DIGITAL EQ
:
0
:
0
:
0
:
0
:
0
: OFF
:EXIT
ADJUST MENU (3)
ADJUST MENU (3)
5
INPUT ATT
:
NORMAL
EFFECT
:
3
ROOM SIZE
:
3
LIVENESS
:
3
∞
:ENTER
:EXIT
ADJUST MENU (4)
ADJUST MENU (4)
5
PANORAMA
:
CENTER WIDTH
:
DIMENSION
:
CENTER GAIN
:
CENTER TONE
:
CNTR ALIGNMENT:
∞
:ENTER
OFF
3
4
0.3
3
OFF
:EXIT
ADJUST MENU (1)
34
33-38RX-D702B[J]_f.p65
34
05.8.25, 1:14 PM
Menu operating procedure
When operating, the on-screen display appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32).
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
In this section, the operation of the remote control is used for explaining.
Ex.: When adjusting subwoofer output level.
Operations
1 To start the adjustment, press
ADJUST.
The setting item previously selected can be shown
on the TV screen by pressing ADJUST on the front
panel when the receiver is in normal operation
mode.
On the TV screen
On the display
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
x
ATT
HP
MHz
kHz
ADJUST MENU (1)
5
SUBWOOFER
LEVEL :
0
FRONT
L
LEVEL :
0
FRONT
R
LEVEL :
0
CENTER
LEVEL :
0
SURR
L
LEVEL :
0
SURR
R
LEVEL :
0
S BACK L
LEVEL :
0
S BACK R
LEVEL :
0
∞
:ENTER
:EXIT
The submenu previously
selected appears.
The setting item previously selected
appears.
2 To select the desired submenu, press
5 or ∞ repeatedly.
There are four screens from “ADJUST MENU (1)” to
“ADJUST MENU (4).” To change the screen, simply
pressing 5 or ∞ repeatedly. You can go to the next/
previous screen.
• On the front panel, turn MULTI JOG.
3 Press SET.
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEPAUTO MODE
x
SUBWOOFER
LEVEL
SUBWOOFER
LEVEL :2
03
The current setting of the
selected item appears.
23:OPERATE
:BACK
The selected submenu appears.
4 To select the appropriate setting, press
2 or 3 repeatedly, then press SET.
The on-screen display returns to the previous
ADJUST MENU. In this example, “ADJUST MENU
(1)” appears on the TV screen and “SUBWFR LVL”
appears on the display.
• On the front panel, turn MULTI JOG, then press
SET.
O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEPAUTO MODE
x
SUBWOOFER
LEVEL
SUBWOOFER
LEVEL :2
–10
03
0
+10
5 Repeat steps 2 to 4 to set other items
if necessary.
NOTE
To exit from menu operations, press EXIT on the remote control. On the front panel, press ADJUST.
35
33-38RX-D702B[J]_f.p65
35
05.8.25, 1:14 PM
Button indications on the screen
From the remote control:
The buttons for operating the menu are shown on the TV screen.
You can operate the menu with these buttons.
ADJUST MENU (1)
5
SUBWOOFER
LEVEL :
0
FRONT
L
LEVEL :
0
FRONT
R
LEVEL :
0
CENTER
LEVEL :
0
SURR
L
LEVEL :
0
SURR
R
LEVEL :
0
S BACK L
LEVEL :
0
S BACK R
LEVEL :
0
∞
:ENTER
:EXIT
LEVEL
SUBWOOFER
LEVEL :2
2
3
4
5
6
7
8
9
10
0
10
1,3
2
1
Usable buttons and their functions
SUBWOOFER
1
Press TEST to check the speakers’ output balance.
• On the TV screen, “TEST TONE” appears. The indicator
corresponding to the speaker appears while a test tone
comes out of the speakers.
EX.:
03
TEST TONE
SW
FL
C
+1
+5
0
FR
-3
SL
+8
23:OPERATE
:BACK
+5
SBL
Usable buttons and their functions
When performing the basic settings viewing the indications
on the display, the indications are slightly different from what
is shown on the on-screen display.
This is because of the limited number of characters shown
on the display.
Ex.: • “SUBWOOFER LEVEL: +10” is shown as “SUBWFR
+10” on the display.
• “BASS BOOST: OFF” is shown as “B BOOST
<OFF>” on the display.
Adjusting the speaker output levels
SUBWOOFER LEVEL (subwoofer output level),
FRONT L LEVEL (left front speaker output level),
FRONT R LEVEL (right front speaker output level),
CENTER LEVEL (center speaker output level),
SURR L LEVEL (left surround speaker output level),
SURR R LEVEL (right surround speaker output level),
S BACK L LEVEL (left surround back speaker output level),
S BACK R LEVEL (right surround back speaker output level)
You can adjust the speaker output levels.
Adjust all the speakers’ output levels so that you can listen to the
sounds from all the speakers at the same level.
• Once you have made an adjustment, it is memorized for each
source.
L
C
R
SR
SBR
SBL
SL
(Back to the beginning)
SW
• You can adjust the speaker output levels without the test
tone.
2
Adjust the speaker output levels.
Press the + or – button corresponding to the speaker
you want to adjust.
3
Press TEST again to stop the test tone.
NOTES
• No test tone comes out of the speakers for which the
speaker setting is set to “NO” (see page 28).
• No test tone is available when the headphones are in use.
• If you have selected “S BACK OUT: 1SPK” for “S BACK
OUT” (see page 29), press S. BACK L +/– to adjust the
output level.
Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)
Initial setting: 0 (dB) for all speakers
NOTES
• If you have selected “NO” for a speaker (see page 28), the
output level for the corresponding speaker is not adjustable.
• If you have selected “HDMI” or “A MULTI” in the audio input
setting (see page 20), “S BACK LEVEL,” “S BACK L LEVEL,”
and “S BACK R LVL” are not adjustable.
• If you have selected “S BACK OUT: 1SPK” for “S BACK OUT”
(see page 29), “S BACK LEVEL” appears instead of “S BACK L
LEVEL” and “S BACK R LEVEL.”
• While using the headphones, you can adjust only the left and
right front speakers’ output level.
36
33-38RX-D702B[J]_f.p65
36
-5
SBR
• On the display, “TEST L” starts flashing, and a test tone
comes out of the speakers clockwise.
Adjusting the items
•
•
•
•
•
•
•
•
SR
-6
05.8.25, 1:14 PM
Adjusting the equalization patterns—
DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz
You can adjust equalization patterns in five frequency bands
(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the
front speakers.
• Once you have made an adjustment, it is memorized for each
source.
Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)
7 Attenuating the input signal—INPUT ATT
When the input level of analog source is too high, the sound will
be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
• Once you have made an adjustment, it is memorized for each
source.
• You cannot adjust this item directly from the remote control.
INPUT ATT: ON
Select to attenuate the input signal level.
The INPUT ATT indicator lights up on
the display.
INPUT ATT: NORMAL
Select to deactivate attenuation.
Initial setting: 0 (dB) for all bands
• When adjustment is made, the DIGITAL EQ indicator lights up
on the display.
If no adjustment is required, set all the frequency bands to
“0 (dB).”
• The DIGITAL EQ indicator goes off from the display.
Initial setting: INPUT ATT: NORMAL
Adjusting the sound parameters for the
Surround/DSP modes
From the remote control:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press D. EQ FREQ repeatedly to
select the band you want to adjust.
2
Press D. EQ LEVEL + or – to adjust
the equalization pattern of the
selected band.
3
Repeat steps 1 and 2 to adjust
other bands.
1
2
3
4
5
6
7
8
9
10
0
10
1
2
You can adjust the Surround/DSP sound parameters to your
preference.
• For details about the Surround/DSP modes, see pages 41 to 43.
7 Adjusting the effect level for DSP modes
—EFFECT
This setting is available only when one of the DSP modes (except
ALL CH STEREO) is in use. To activate DSP mode, see page 45.
• Once you have made an adjustment, it is memorized for each
DSP mode.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: EFFECT: 3
As the number increases, the effect becomes stronger.
Normally, select “3.”
Adjusting the bass sounds
From the remote control:
7 Reinforcing the bass—BASS BOOST
Press EFFECT repeatedly to select the level you want to
adjust.
You can boost the bass level—Bass Boost.
• Once you have made an adjustment, it is memorized for each
source.
• You cannot adjust this item directly from the remote control.
BASS BOOST: ON
Select to boost the bass level.
The B.BOOST indicator lights up on the
display.
BASS BOOST: OFF
Select to deactivate the Bass Boost.
1
2
3
4
5
6
7
8
9
10
0
10
Initial setting: BASS BOOST: OFF
NOTE
This function affects only the sound coming out through the front
speakers.
7 Adjusting the virtual room size for DSP modes
—ROOM SIZE
This setting is available only when one of the DSP modes (except
ALL CH STEREO) is in use. To activate DSP mode, see page 45.
• If “SURROUND SPK” is set to “NO” (see page 28), this item is
not adjustable.
• Once you have made an adjustment, it is memorized for each
DSP mode.
• You cannot adjust this item directly from the remote control.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: ROOM SIZE: 3
As the number increases, the interval between reflections
increases so that you will feel as if you were in a larger room.
Normally, select “3.”
37
33-38RX-D702B[J]_f.p65
37
05.8.25, 1:14 PM
7 Adjusting the liveness effect for DSP modes
—LIVENESS
7 Adjusting the sound localization of the center
channel—CENTER GAIN
This setting is available only when one of the DSP modes (except
ALL CH STEREO) is in use. To activate DSP mode, see page 45.
• If “SURROUND SPK” is set to “NO” (see page 28), this item is
not adjustable.
• Once you have made an adjustment, it is memorized for each
DSP mode.
• You cannot adjust this item directly from the remote control.
This setting is available only when Neo:6 Music is in use.
• If “CENTER SPK” is set to “NO” (see page 28), this item is not
adjustable.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot adjust this item directly from the remote control.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: LIVENESS: 3
As the number increases, the attenuation level of reflections over
time decreases so that acoustics change from “Dead” to “Live.”
Normally, select “3.”
7 Adjusting the panorama control for Pro Logic IIx
Music and Pro Logic II Music—PANORAMA
This setting is available when Pro Logic IIx Music or Pro Logic II
Music is activated for the analog or digital 2-channel sound signal.
To activate Pro Logic IIx Music or Pro Logic II Music, see page 45.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot adjust this item directly from the remote control.
PANORAMA: ON
Select to add “wraparound” sound effect
with side-wall image.
PANORAMA: OFF
Select to listen to originally recorded
sound.
Initial setting: PANORAMA: OFF
7 Adjusting the center channel localization for Pro
Logic IIx Music and Pro Logic II Music—CENTER
WIDTH
Adjustable range: 0 to 1.0 (in 0.1 step intervals)
Initial setting: CENTER GAIN: 0.3
As the number increases, the center channel will be localized
clearly.
Normally, select “0.3.”
7 Adjusting the center tone—CENTER TONE
This setting is available when one of the Surround/DSP modes is
in use. To activate Surround/DSP mode, see page 45.
• If “CENTER SPK” is set to “NO” (see page 28), this item is not
adjustable.
• This setting is common to all Surround modes, and is
memorized separately for DSP modes.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: CENTER TONE: 3
As the number increases, the dialogue becomes stronger.
Normally, select “3.”
• When the center tone is set to other than “CENTER TONE: 3,”
the C.TONE indicator lights up on the display.
From the remote control:
Press C. TONE repeatedly to select the level you want to
adjust.
1
2
3
4
5
6
7
8
9
10
0
10
This setting is available when Pro Logic IIx Music or Pro Logic II
Music is activated for the analog or digital 2-channel sound signal.
To activate Pro Logic IIx Music or Pro Logic II Music, see page 45.
• If “CENTER SPK” is set to “NO” (see page 28), this item is not
adjustable.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot adjust this item directly from the remote control.
Adjustable range: OFF and 1 to 7 (in 1 step intervals)
Initial setting: CENTER WIDTH: 3
As the number increases, the center channel sound moves
toward the left and right speakers.
Normally, select “3.”
7 Adjusting the sound localization position for Pro
Logic IIx Music and Pro Logic II Music
—DIMENSION
This setting is available when Pro Logic IIx Music or Pro Logic II
Music is activated for the analog or digital 2-channel sound signal.
To activate Pro Logic IIx Music or Pro Logic II Music, see page 45.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot adjust this item directly from the remote control.
Adjustable range: 1 to 7 (in 1 step intervals)
7 Aligning the vertical localization of the center
channel for Surround/DSP modes
—CNTR ALIGNMENT
This setting is available when one of the Surround/DSP modes
(except PLIIx MUSIC, PLII MUSIC, NEO:6 MUSIC, and ALL CH
STEREO) is in use. To activate Surround/DSP mode, see page
45.
• If “CENTER SPK” is set to “NO” (see page 28), this item is not
adjustable.
• Once you have made an adjustment, it is memorized for each
Surround/DSP mode.
• You cannot adjust this item directly from the remote control.
CNTR ALIGNMENT: ON
Select this when you cannot feel as
if the actors or singers are
speaking or singing on the screen.
CNTR ALIGNMENT: OFF
Center alignment is turned off.
Initial setting: DIMENSION: 4
As the number increases, the sound localization moves towards
forward from backward.
Normally, select “4.”
Initial setting: CNTR ALIGNMENT: OFF
38
33-38RX-D702B[J]_f.p65
38
05.8.25, 1:14 PM
Tuner operations
Tuning in to stations manually
From the remote control ONLY:
1 Press FM/AM to select the band.
The last received station of the selected band is tuned in.
• Each time you press the button, the band alternates
between “FM” and “AM.”
ANALOG
TUNED STEREO AUTO MUTING
L
R
S.WFR
MHz
Tuner operations are mainly done from the remote control.
2 Press repeatedly or hold TUNING 9 or
( TUNING until the station you want is
tuned in.
• Pressing (or holding) TUNING 9 increases the
frequency.
• Pressing (or holding) ( TUNING decreases the
frequency.
NOTES
• When you hold and release TUNING 9 or ( TUNING, the
frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the
TUNED indicator lights up on the display.
• When an FM stereo program is received, the STEREO
indicator also lights up.
FM/AM
TUNING/REW
FF/TUNING
Using preset tuning
Once a station is assigned a channel number, the station can
be quickly tuned simply by selecting the number. You can
preset up to 30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
1
2
3
4
5
6
8
9
7
FM MODE
10
0
There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step 2 again.
From the remote control ONLY:
10
MEMORY
1 Tune in to the station you want to preset
(see “Tuning in to stations manually”
above).
• If you want to store the FM reception mode for this
station, select the FM reception mode you want. See
“Selecting the FM reception mode” on page 40.
ANALOG
TUNED STEREO AUTO MUTING
L
R
S.WFR
MHz
2 Press MEMORY.
The channel number position starts flashing on the
display for about 5 seconds.
ANALOG
TUNED STEREO AUTO MUTING
L
NOTE
R
S.WFR
MHz
When you have selected “FM” or “AM” by using SOURCE
SELECTOR on the front panel, the remote control may not
work for tuner operations. To use the remote control for tuner
operations, select “FM” or “AM” by using FM/AM button on the
remote control.
CONTINUED ON THE NEXT PAGE
39
39-40RX-D702B[J]_f.p65
39
05.8.25, 1:04 PM
3 Press the numeric buttons (1 – 10, +10) to
On the front panel:
select a channel number while the channel
number position is flashing.
2 1,3
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
ANALOG
TUNED STEREO
L
Before you start, remember...
AUTO MUTING
R
S.WFR
MHz
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1 Turn SOURCE SELECTOR to select “FM” or
4 Press MEMORY again while the selected
channel number is flashing on the display.
The selected channel number stops flashing.
The station is assigned to the selected channel number.
“AM.”
The last received station of the selected band is tuned in.
2 Press TUNER PRESET.
5 Repeat steps 1 to 4 until you store all the
“P” appears on the display, and MULTI JOG now works for
selecting preset channels.
stations you want.
3 Turn MULTI JOG to select a preset channel
To erase a stored preset station
number.
Storing a new station on a used channel number erases the
previously stored one.
• To increase the preset channel numbers, turn MULTI JOG
clockwise.
• To decrease the preset channel numbers, turn MULTI JOG
counterclockwise.
To tune in a preset station
From the remote control:
Selecting the FM reception mode
1 Press FM/AM to select the band.
The last received station of the selected band is tuned in and
the numeric buttons now work for tuner operations.
• Each time you press the button, the band alternates
between “FM” and “AM.”
ANALOG
TUNED STEREO
L
AUTO MUTING
R
S.WFR
MHz
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station
(see page 39).
From the remote control ONLY:
While listening to an FM station, press FM MODE.
• Each time you press the button, the FM reception mode
alternates between “AUTO MUTING” and “MONO.”
2 Press the numeric buttons (1 – 10, +10) to
select a preset channel number.
ANALOG
TUNED STEREO
L
AUTO MUTING
Normally select this.
When a program is broadcast in stereo,
you will hear stereo sound; when in
monaural, you will hear monaural sound.
This mode is also useful to suppress
static noise between stations. The AUTO
MUTING indicator lights up on the display.
MONO
Select this to improve the reception (but
stereo effect will be lost).
In this mode, you will hear noise while
tuning in to the stations. The AUTO
MUTING indicator goes off from the
display. (The STEREO indicator also goes
off.)
AUTO MUTING
R
S.WFR
MHz
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
Initial setting: AUTO MUTING
40
39-40RX-D702B[J]_f.p65
40
05.8.25, 1:04 PM
Creating realistic
sound fields
Introducing the Surround modes
■ Dolby Digital*
Dolby Digital is a digital signal compression method, developed by
Dolby Laboratories, and enables multi-channel encoding and
decoding.
• When Dolby Digital signal is detected through the digital input,
the
indicator lights up on the display.
Dolby Digital 5.1CH
Reproducing theater ambience
In a movie theater, many speakers are located on the walls to
reproduce impressive multi-channel sound, reaching you from all
directions.
With these many speakers, sound localization and sound
movement can be expressed.
Surround/DSP modes built in this receiver can create almost the
same Surround sound as you can feel in a real movie theater.
Dolby Digital 5.1CH (DOLBY DIGITAL) encoding method records
and digitally compresses the left front channel, right front channel,
center channel, left surround channel, right surround channel, and
LFE channel signals (total 6 channels, but the LFE channel is
counted as 0.1 channel. Therefore, called 5.1 channel).
Dolby Digital enables stereo surround sounds, and sets the cutoff
frequency of the surround treble at 20 kHz, compared to 7 kHz for
Dolby Pro Logic. As such, the sound movement and “being-there”
feeling are enhanced much more than Dolby Pro Logic.
Dolby Digital EX
Dolby Digital EX (DOLBY D EX) is a digital surround encoding
format that adds the third surround channels, called “surround
back.”
Compared to the conventional Dolby Digital 5.1CH, these newly
added surround back channels can reproduce more detailed
movements behind you while viewing the video software. In
addition, surround sound localization will become more stable.
■ Dolby Surround
Dolby Pro Logic II
Dolby Pro Logic II is a multi-channel playback format to convert
2-channel software into 5-channel (plus subwoofer). The matrixbased conversion method used for Dolby Pro Logic II makes no
limitation for the cutoff frequency of the surround treble and
enables stereo surround sound.
• This receiver provides three types of Dolby Pro Logic II
modes—Pro Logic II Movie (PLII MOVIE), Pro Logic II Music
(PLII MUSIC), and Pro Logic II Game (PLII GAME).
When Dolby Pro Logic II is activated, the
indicator lights
up on the display.
SW
C
FL
SBL
(SB)
Suitable for playing any Dolby Surround encoded
software. You can enjoy a sound field very close
to the one created with discrete 5.1-channel
sounds.
PLII MUSIC
Suitable for playing any 2-channel stereo
software. You can enjoy wide and deep sounds.
PLII GAME
Suitable for playing a video game. You can enjoy
sounds with “being there” feeling.
FR
SR
SL
PLII MOVIE
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
SBR
CONTINUED ON THE NEXT PAGE
41
41-45RX-D702B[J]_f.p65
41
05.8.25, 1:05 PM
Dolby Pro Logic IIx
DTS Neo:6
Dolby Pro Logic IIx is a newly introduced multi-channel playback
format to convert not only multi-channel software but 2-channel
software into 7.1 channel (or 6.1 channel) that developed from
Dolby Pro Logic II. The matrix-based conversion method used for
Dolby Pro Logic IIx makes no limitation for the cutoff frequency of
the surround treble.
• This receiver provides three types of Dolby Pro Logic IIx
modes—Pro Logic IIx Movie (PLIIx MOVIE), Pro Logic IIx
Music (PLIIx MUSIC), and Pro Logic IIx Game (PLIIx GAME).
When Dolby Pro Logic IIx is activated, “PLIIx MOVIE,” “PLIIx
MUSIC,” or “PLIIx GAME” appear and the
indicator
lights up on the display.
DTS Neo:6 is another conversion method to create 6-channel
(plus subwoofer) from analog/digital 2-channel software by using
the high precision digital matrix decoder used for DTS-ES Matrix
6.1ch.
• This receiver provides the following DTS Neo:6 modes—Neo:6
Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
When one of them is activated, the NEO:6 indicator lights up on
the display.
PLIIx MOVIE
Suitable for playing any Dolby Surround encoded
software. You can enjoy a sound field with a
natural wraparound effect.
PLIIx MUSIC
Suitable for playing any 2-channel stereo
software. You can enjoy wide and deep 7.1channel sounds.
PLIIx GAME
Suitable for playing a video game. You can enjoy
7.1-channel sounds with “being there” feeling.
This mode is available for both an analog and
digital 2-channel signal.
• To enjoy software encoded with Dolby Digital, connect the
source component using the digital terminal on the rear of this
receiver. (See page 16.)
■ DTS**
DTS is another digital signal compression method, developed by
Digital Theater Systems, Inc., and enables multi-channel
encoding and decoding (1ch up to 6.1ch).
• When DTS signal is detected through the digital input, the
indicator lights up on the display.
NEO:6 CINEMA Suitable for playing movies. You can get the
same atmosphere with 2-channel software as
with 6.1-channel software. It is also effective for
playing software encoded with conventional
surround formats.
NEO:6 MUSIC
Suitable for playing music software. The front
channel signals bypass the decoder (resulting in
no loss of sound quality) and the surround
signals transmitted through the other speakers
expand the sound field naturally.
** “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks
of Digital Theater Systems, Inc.
When using Surround mode, the sounds come out of the
activated speakers which the Surround mode requires.
• If either “SURROUND SPK” or “CENTER SPK” is set to “NO”
in the speaker setting (see page 28), the corresponding
channel signals are allocated to and emitted through the front
speakers.
• If both “SURROUND SPK” and “CENTER SPK” are set to
“NO” in the speaker setting (see page 28), JVC’s original 3DPHONIC processing (which has been developed to create the
surround effect through the front speakers only) is used. The
3D-PHONIC indicator lights up on the display.
DTS Digital Surround
DTS Digital Surround (DTS) is another discrete 5.1 channel
digital audio format available on CD, LD, and DVD software.
Compared to Dolby Digital, the DTS Digital Surround format has a
lower audio compression rate which enables it to add breadth and
depth to the sounds reproduced. As such, DTS Digital Surround
features natural, solid, and clear sound.
DTS Extended Surround (DTS-ES)
DTS-ES is another multi-channel digital encoding format.
It greatly improves the 360-degree surround impression and
space expression by adding the third surround channel—surround
back channel.
DTS-ES includes two signal formats with different surround signal
recording methods—DTS-ES Discrete 6.1ch (ES DISCRETE)
and DTS-ES Matrix 6.1ch (ES MATRIX).
DTS-ES Discrete 6.1ch has been designed to encode (and
decode) a 6.1-channel signal discretely to avoid interference with
each channel.
DTS-ES Matrix 6.1ch has been designed to add an extra
surround channel to DTS Digital Surround 5.1-channel. By using a
matrix encoding/decoding method, an additional “surround back”
channel signal is encoded (and decoded) in both the left and right
surround channel signals.
DTS 96/24
In recent years, there has been increasing interest in higher
sampling rates both for recording and for reproducing at home.
Higher sampling rates allow wider frequency range and greater bit
depths provide extended dynamic range.
DTS 96/24 is a multi-channel digital signal format (fs 96 kHz/24
bits) introduced by Digital Theater Systems, Inc. to deliver “betterthan-CD sound quality” into the home.
and 96/24
• When DTS 96/24 signal is detected, the
indicators light up. You can enjoy its 5.1-channel sound with fullquality.
About other digital signals
Linear PCM
Uncompressed digital audio data used for DVDs, CDs, and
Video CDs.
DVDs support 2 channels with sampling rates of 48/96 kHz, at
quantization of 16/20/24 bits. On the other hand, CDs and
Video CDs are limited to 2 channels with 44.1 kHz at 16 bits.
• When Linear PCM signal is detected, the LINEAR PCM
indicator lights up.
Multi channel PCM
Uncompressed multi channel digital audio data used for DVDAudios.
DVD-Audios support up to 5.1 channels with sampling rates of
44.1/48/88.2/96 kHz and 2 channels with sampling rates of
44.1/48/88.2/96/176/192 kHz, at quantization of 16/20/24 bits.
• When Multi channel PCM signal is detected, the LINEAR
PCM indicator lights up and “MULTI CH PCM” appears on
the display for a while.
Dual Mono
Dual Mono can be easily understood when you think of the
bilingual broadcast for TV programs (however, the Dual Mono
format is not identical with those analog formats).
This format is now adopted in Dolby Digital, DTS, and so on. It
allows two independent channels (called main channel and
sub-channel) to be recorded separately.
• You can select either channel you want to listen to (see
page 30).
42
41-45RX-D702B[J]_f.p65
42
05.8.25, 1:05 PM
Introducing the DSP modes
The sound heard in a concert hall, club, etc. consists of direct
sound and indirect sound—early reflections and reflections from
behind. Direct sounds reach the listener directly without any
reflection. On the other hand, indirect sounds are delayed by the
distances of the ceiling and walls. These direct sounds and
indirect sounds are the most important elements of the acoustic
surround effects.
The DSP modes can create these important elements, and give
you a real “being there” feeling.
Reflections from behind
Early reflections
When using the DAP mode, the sounds come out of all the
connected and activated speakers.
• If “SURROUND SPK” is set to “NO” in the speaker setting
(see page 28), JVC’s original 3D-PHONIC processing (which
has been developed to create the surround effect through the
front speakers only) is used.
The 3D-PHONIC indicator lights up on the display.
■ MONO FILM
In order to reproduce a more acoustic sound field in your listening
room while viewing monaural sound video software (analog and
2-channel digital signals including Dual Mono signal), you can use
this mode.
The surround effect will be added, and the sound localization of
actor’s words will be improved.
This mode cannot be used for multi-channel digital signals.
Direct sounds
The DSP modes include the following modes:
• Digital Acoustic Processor (DAP) modes—HALL1, HALL2, LIVE
CLUB, DANCE CLUB, PAVILION, THEATER1, THEATER2
• MONO FILM—Used for all types of 2-channel signals (including
Dual Mono signal)
• All Channel Stereo mode (ALL CH STEREO)
When one of the DSP modes is activated, the DSP indicator lights
up on the display.
When “MONO FILM” is used, sounds come out of all the
connected (and activated) speakers.
• If “SURROUND SPK” is set to “NO” in the speaker setting
(see page 28), JVC’s original 3D-PHONIC processing (which
has been developed to create the surround effect through the
front speakers only) is used.
The 3D-PHONIC indicator lights up on the display.
• If incoming signals change from 2-channel digital signal to
another digital signal type, “MONO FILM” is canceled and an
appropriate Surround mode is activated.
■ All Channel Stereo mode (ALL CH STEREO)
This mode can reproduce a larger stereo sound field using all the
connected (and activated) speakers. This mode cannot be used
if “SURROUND SPK” is set to “NO” in the speaker setting
(see page 28).
■ Digital Acoustic Processor (DAP) modes
You can use the following DAP modes in order to reproduce a
more acoustic sound field in your listening room.
HALL1
Reproduces the spatial feeling of a large
shoebox-shaped hall designed primarily for
classical concerts. (Its seating capacity is about
2000.)
HALL2
Reproduces the spatial feeling of a large
vineyard-shaped hall designed primarily for
classical concerts. (Its seating capacity is about
2000.)
LIVE CLUB
Reproduces the spatial feeling of a live music club
with a low ceiling.
DANCE CLUB Reproduces the spatial feeling of a rocking dance
club.
PAVILION
Reproduces the spatial feeling of an exhibition
hall with a high ceiling.
THEATER1
Reproduces the spatial feeling of a large theater
where the seating capacity is about 600.
THEATER2
Reproduces the spatial feeling of a small theater
where the seating capacity is about 300.
Sound reproduced from
normal stereo
Sound reproduced from All
Channel Stereo mode
3D HEADPHONE mode
If you connect a pair of headphones while one of the
Surround/DSP modes is in use, the 3D HEADPHONE mode is
activated without respect to the type of software played back.
“3D HEADPHONE” appears on the display and the DSP and
HEADPHONE indicators light up.
NOTE
When “THEATER1” or “THEATER2” is activated while playing
back 2-channel analog or digital source, the built-in Dolby Pro
Logic II decoder is activated and the
indicator lights up.
43
41-45RX-D702B[J]_f.p65
43
05.8.25, 1:05 PM
Using the Surround/DSP modes
Available Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.
• The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the
surround channels. For example, (3/2) indicates that the signals are encoded with three front signals (left/right/center) and two (stereo)
surround signals.
• For EX/ES/PLIIx setting, see page 30.
• Surround/DSP modes are not available when selecting “A MULTI” in the audio input setting (see page 20) or when multi channel PCM
(see page 42) signals recorded in DVD-Audio are coming in.
EX/ES/PLIIx setting
Incoming Signal Type
Dolby Digital
AUTO
ON
3,5
PLIIx MOVIE
3
Dolby Digital Surround EX
DOLBY D EX*
DOLBY D EX*
D+PLIIx MOVIE*
Dolby Digital (3/2, 2/2)
DOLBY DIGITAL
DOLBY D EX*3
D+PLIIx MOVIE*2,3
Dolby Digital (3/1, 2/1, 3/0, 1/0)
OFF
3
D+PLIIx MUSIC*
DOLBY DIGITAL
D+PLIIx MUSIC*3
DOLBY DIGITAL
DOLBY DIGITAL
Dolby Digital (Dual Mono)
DTS
PLIIx MUSIC
2,3
DUAL MONO
DTS-ES Discrete*1
DTS-ES DSCRT*3
DTS-ES DSCRT*3
DTS+PLIIx MOVIE*2,3 DTS+PLIIx MUSIC*3
DTS SURROUND
DTS-ES Matrix*1
DTS-ES MATRIX*3
DTS-ES MATRIX*3
DTS+PLIIx MOVIE*2,3 DTS+PLIIx MUSIC*3
DTS SURROUND
DTS (3/2, 2/2)*1
DTS SURROUND
DTS+NEO:6*3
DTS+PLIIx MOVIE*2,3 DTS+PLIIx MUSIC*3
DTS SURROUND
DTS (3/1, 2/1, 3/0, 1/0)
DTS (Dual Mono)
DTS
DUAL MONO
Analog/LINEAR PCM
Dolby Digital (2/0)
PLIIx MOVIE*4/
PLIIx MUSIC*4/
PLIIx GAME*4/
NEO:6 CINEMA/
NEO:6 MUSIC
PLII MOVIE/
PLII MUSIC/
PLII GAME/
NEO:6 CINEMA/
NEO:6 MUSIC
*1 DTS 96/24 processing is not applied when the EX/ES/PLIIx setting is activated. If you want to apply the processing, set the EX/ES/
PLIIx setting to “OFF” (see page 30).
*2 When “S BACK OUT” is set to “SB OUT: 1SPK,”
D+PLIIx MOVIE is changed to DOLBY D EX and DTS+PLIIx MOVIE is changed to
DTS+ EX.
*3 When “S BACK SPK” is set to “NO,” Virtual Surround Back is activated for the modes and the VIRTUAL SB indicator lights up on the
display.
*4 When “S BACK SPK” is set to “NO,” PLllx MOVIE, PLllx MUSIC, and PLllx GAME are changed to PLll MOVIE, PLll MUSIC, and PLll
GAME respectively.
*5 For some Dolby Digital Surround EX software, Dolby Digital 5.1-channel reproduction (“DOLBY DIGITAL”) may be applied even
though you have selected “AUTO”. In this case, select “ON” to apply “DOLBY D EX.”
About the DSP modes
• The following DSP modes are available except when selecting “A MULTI” in the audio input setting (see page 20) or when multi
channel PCM (see page 42) signals recorded in DVD-Audio are coming in.
HALL1, HALL2, LIVE CLUB, DANCE CLUB, PAVILION, THEATER1, THEATER2
• If an incoming signal is a multi-channel (more than 2 channel) digital signal, “MONO FILM” is not available.
• If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is not available.
Virtual Surround Back
This function creates the great surround effect from the behind as if you have connected the surround back speaker. The VIRTUAL
SB (Surround Back) indicator lights up on the display.
If you have connected (and activated) the surround speakers, you can use Virtual Surround Back without connecting the surround
back speaker.
Virtual Surround Back is activated when EX/ES/PLIIx is set to other than “OFF” and when playing back the software including the
following signals:
– Dolby Digital Surround EX
– DTS-ES
– Dolby Digital or DTS with 4-channels or more
44
41-45RX-D702B[J]_f.p65
44
05.8.25, 1:05 PM
Activating the Surround/DSP modes
On the front panel:
2
1,3
Available Surround/DSP modes vary depending on the speaker
settings and the incoming signals. For details, see page 44.
Activating one of the Surround/DSP modes automatically
recalls the memorized settings and adjustments.
• To adjust the speaker output level, see page 36.
• When activating one of the Surround/DSP modes, you
can adjust CENTER TONE. (see page 38)
• When activating one of the Surround/DSP modes
(except PLIIx MUSIC, PLII MUSIC, NEO:6 MUSIC, and
ALL CH STEREO), you can adjust CNTR ALIGNMENT. (see
page 38)
• When activating “NEO:6 MUSIC,” you can adjust CENTER
GAIN. (see page 38)
• When activating the DSP mode (except ALL CH
STEREO), you can adjust the following settings:
EFFECT (see page 37)
ROOM SIZE (see page 37)
LIVENESS (see page 38)
• When activating “PLIIx MUSIC” and “PLII MUSIC”, you
can adjust the following settings:
PANORAMA (see page 38)
CENTER WIDTH (see page 38)
DIMENSION (see page 38)
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1 Select and play any source.
• Surround/DSP modes are not available when selecting “A
MULTI” in the audio input setting (see page 20) or when
multi channel PCM (see page 42) signals recorded in DVDAudio are coming in.
• Make sure you have selected the input mode (analog or
digital) correctly.
2 Press SURROUND.
MULTI JOG now works for selecting Surround/DSP modes.
3 Turn MULTI JOG to select the Surround/DSP
mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
DIGITAL AUTO
Selecting the Surround/DSP modes
DIGITAL
L
C
R
S.WFR LFE
LS
RS
From the remote control:
1
1
4
2
3
5
6
7
8
9
10
0
10
2
1 Select and play any source.
• Surround/DSP modes are not available when selecting “A
MULTI” in the audio input setting (see page 20) or when
multi channel PCM (see page 42) signals recorded in DVDAudio are coming in.
• Make sure you have selected the input mode (analog or
digital) correctly.
2 Press SURROUND repeatedly to select the
Surround/DSP mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
DIGITAL AUTO
DIGITAL
L
C
R
S.WFR LFE
LS
RS
Surround modes*2
AUTO SURROUND*1
HALL1
HALL2
LIVE CLUB
DANCE CLUB
PAVILION
THEATER1
THEATER2
MONO FILM*3
ALL CH STEREO*4
(Back to the beginning)
SURROUND OFF
*1 “AUTO SURROUND” is the initial setting.
*2 Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page
44.
*3 If an incoming signal is a multi-channel (more than 2
channel) digital signal, “MONO FILM” is not available.
*4 If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is
not available.
AUTO SURROUND*1
Surround modes*2
HALL1
HALL2
LIVE CLUB
DANCE CLUB
PAVILION
THEATER1
THEATER2
MONO FILM*3
ALL CH STEREO*4
(Back to the beginning)
SURROUND OFF
*1 “AUTO SURROUND” is the initial setting.
*2 Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page
44.
*3 If an incoming signal is a multi-channel (more than 2
channel) digital signal, “MONO FILM” is not available.
*4 If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is
not available.
To cancel Surround/DSP modes
Turn MULTI JOG so that “SURROUND OFF” appears on the
display.
When you select “AUTO SURROUND”
You can enjoy the Surround mode easily.
• For details about the Surround modes, see page 44.
• When “AUTO SURROUND” is activated, the AUTO SURR indicator
lights up on the display.
How does “AUTO SURROUND” work?
• If a multi-channel signal comes in, an appropriate Surround
mode will be selected automatically.
• If a Dolby Digital 2-channel signal with surround signal comes
in, “PLIIx MOVIE” or “PLII MOVIE” will be selected.
• If a Dolby Digital 2-channel signal without surround signal
comes in, “SURROUND OFF (stereo)” will be selected.
• If a Linear PCM signal comes in, “SURROUND OFF (stereo)”
will be selected.
NOTE
“AUTO SURROUND” does not take effect in the following cases:
– While playing an analog source,
– While selecting one of the fixed digital decode mode—“DOLBY
DIGITAL” or “DTS” (see page 21).
To cancel Surround/DSP modes
Press SURROUND repeatedly so that “SURROUND OFF”
appears on the display.
45
41-45RX-D702B[J]_f.p65
45
05.8.25, 1:05 PM
NOTES
AV COMPU LINK
remote control
system
• When connecting the receiver and a TV with the AV COMPU LINK
EX terminal by using a component video cable, you cannot use
Automatic selection of TV’s input mode (see page 47).
• When connecting only the VCR and DVD player to this receiver,
connect it directly to the receiver using cable with the monaural
mini-plugs.
• You can connect only the TV with AV COMPU LINK EX or AV
COMPU LINK-III terminal to the AV COMPU LINK-III terminal.
Connections 2: Video cable connection
The AV COMPU LINK remote control system allows you to
operate JVC’s video components (TV, DVD player*, and VCR)
through this receiver.
This receiver is equipped with the AV COMPU LINK-III, which has
added a function to operate JVC’s video components through the
component video jacks. To use this remote control system, you
need to connect the video components you want to operate,
following the diagrams below and the procedures on page 47.
• Refer also to the manuals supplied with your video components.
* “DVD player” on pages 46 and 47 can be replaced with “DVD
recorder.”
Connections 1: AV COMPU LINK connection
TV
AV
COMPU LINK-III
AV
COMPU LINK EX
This receiver is equipped with three types of the video terminals
other than the HDMI terminals—composite video, S-video, and
component video, and the signals coming into this receiver
through one type of video terminals can output only through the
terminal of the same type. So you need to connect the video
components to this receiver using one of the following three ways.
• When using the AV COMPU LINK remote control system, set
the video output and video input setting for the DVD player and
the VCR correctly (see “Selecting the video input setting” on
page 20 and “Selecting the output video signals—VIDEO
OUTPUT” on page 32); otherwise, the correct input for this
receiver will not be selected on the TV.
Case 1:
When connecting the source equipment to the receiver
through the S-video terminals, connect this receiver to the
TV’s video input 1 terminal using S-video cables.
S-video cable
Source
equipment
RX-D702B
Monaural mini-plugs
(not supplied)
AV
COMPU LINK-III
Case 2:
When connecting the source equipment to the receiver
through the composite video jacks, connect this receiver
to the TV’s video input 2 terminal (composite video input)
using composite video cables.
Source
equipment
RX-D702B
AV
COMPU LINK
IMPORTANT:
Source
equipment
RX-D702B
46
46
Component video cable
TV
To video input 2
(Component)
The AV COMPU LINK remote control system cannot control the
DBS tuner connected to the DBS IN jacks.
46-47RX-D702B[J]_f.p65
TV
Case 3:
When connecting the source equipment to the receiver
through the component video jacks, connect this receiver
to the TV’s video input 2 terminals (component video
input) using component video cables.
Component video cable
VCR
Composite video cable
To video input 2
(Composite)
AV
COMPU LINK
DVD player
TV
To video input 1
Composite video cable
Monaural
mini-plugs
(not supplied)
S-video cable
05.8.25, 1:05 PM
Connecting procedure
1 If you have already plugged your VCR, DVD
player, TV, and this receiver into the AC
outlets, unplug their AC power cords first.
2 Connect your VCR, DVD player, TV, and this
receiver as follows, using the cables with the
monaural mini-plugs (not supplied).
• See “Connections 1” on the previous page.
3 Connect the audio input/output jacks on the
VCR, DVD player, TV, and this receiver using
the audio cables.
• See pages 10 to 13.
4 Connect the video input/output jacks on the
VCR, DVD player, TV, and this receiver using
the S-video cables, composite video cables,
or component video cables.
• See “Connections 2” on the previous page.
5 Plug the AC power cords of the connected
components and this receiver into the AC
outlets.
6 When turning on the TV for the first time after
the AV COMPU LINK connection, turn the TV
volume to the minimum using the TV volume
control on the TV.
7 Turn on other connected components first,
then turn on this receiver.
• When turning on the VCR, use the remote control supplied
with this receiver (press VCR
).
The AV COMPU LINK remote control system allows you to use
the five basic functions listed below.
Remote control of the TV, DVD player, and VCR using this
remote control
One-touch DVD play
Simply by starting playback on the DVD player, you can enjoy the
DVD playback without setting other switches manually.
The following is set automatically:
• Turning on the receiver.
• Changing the source to “DVR/DVD.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
Automatic selection of TV’s input mode
• When you select “TV” as the source to play on the receiver, the
TV automatically changes the input mode to the TV tuner so
that you can watch TV.
• When you select “DVR/DVD,” “VCR,” “DBS,” or “AUX” as the
source to play on the receiver with “VIDEO OUTPUT” (see page
32) set to the setting other than “VIDEO OUTPUT: HDMI,” the
TV automatically changes the input mode to the appropriate
position (either video input 1 or video input 2) so that you can
view the playback picture.
NOTE
This function does not work when you connect this receiver and
the TV with the AV COMPU LINK EX terminal using a component
video cable. In this case, reconnect the TV referring to Case 1 or
Case 2 on page 46.
Automatic power on/off
The TV, DVD player, and VCR turn on and off along with the
receiver.
When you turn on the receiver;
• If the previously selected source is “TV” or “DBS,” only the TV
will turn on automatically.
• If the previously selected source is “DVR/DVD,” the TV and DVD
player will turn on automatically.
• If the previously selected source is “VCR,” the TV and VCR will
turn on automatically.
When you turn off the receiver, the TV, DVD player, and VCR will
turn off.
NOTE
If you turn off the receiver while recording on the VCR, the VCR
will not turn off, but continue recording.
See pages 48 and 49 for details.
• Aim the remote control directly at the remote sensor on each
component.
One-touch video play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy the video playback without setting other
switches manually. The receiver automatically turns on and
changes the source to “VCR.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab, press the
play (3) button on the VCR or on the remote control. So, you can
get the same result.
47
46-47RX-D702B[J]_f.p65
47
05.8.25, 1:05 PM
Operating other
JVC products
7 VCR
7 SIRIUS radio
You can use the supplied remote control to operate not only
this receiver but also other JVC products.
• Refer also to the manuals supplied with the other products.
– Some JVC VCRs can accept two types of the control
signals—remote codes “A” and “B.” This remote control can
operate a VCR whose remote control code is set to “A.”
– Some JVC DVD recorders can accept four types of the control
signals. This remote control can operate a DVD recorder
whose remote control code is set to the initial code. For
details, refer to the manual supplied with the DVD recorder.
• To operate other products, aim the remote control directly at the
remote sensor on the target product.
7 TV
1
2
3
1
2
3
4
5
6
4
5
6
7
8
9
7
8
9
10
0
10
10
0
10
You can always perform the following operation:
VCR
:
Turn on or off the VCR.
After pressing VCR, you can perform the following operations on
the VCR.
1
2
3
4
5
6
7
8
9
10
0
10
CHANNEL +/–:
Change the channel numbers on the VCR.
1 – 9, 0:
Select the channel numbers on the VCR.
3:
Start playback.
7:
Stop playback.
8:
Pause playback. To release it, press 3.
FF:
Fast-wind a tape.
REW:
Rewind a tape.
+ 3:
Start recording.
+ 8:
Enter recording pause. To start recording,
press 3.
After pressing SIRIUS, you can perform the following operations
on the SIRIUS radio.
You can always perform the following operations:
TV/SIRIUS
:
Turn on or off the SIRIUS radio.
CAT 9/( CAT:
Change the category of the program.
TV VOL +/–:
Adjust the volume on the TV.
CHANNEL +/–:
TV/VIDEO:
Change the input mode (either video
input or TV tuner) on the TV.
Change the channel numbers on the
SIRIUS radio.
1 – 6, BAND:
Store or tune in to the preset channel.
MEMO:
Store information on the display of the
SIRIUS radio.
SELECT:
Select an highlighted item on the display of
the SIRIUS radio.
DISP:
Change the text size on the display of the
SIRIUS radio.
PREV:
Return to the previous channel.
After pressing TV, you can perform the following operations on the
TV.
TV/SIRIUS
:
Turn on or off the TV.
CHANNEL +/–:
Change the channel numbers.
1 – 9, 0, 100+ (+10):
Select the channel numbers.
RETURN (10):
Switch between the previous channel
and the current channel.
NOTE
The remote control may not operate properly for a SIRIUS radio
other than KT-SR2000 (JVC SIRIUS radio).
48
48-52RX-D702B[J].p65
48
05.8.25, 1:05 PM
7 DVD recorder or DVD player
You can always perform the following operation:
DVR/DVD
1
2
3
4
5
6
7
8
9
10
0
10
:
Turn on or off the DVD recorder or DVD
player.
To operate the DVD
recorder, set the
mode selector to
“DVR.”
After pressing DVR/DVD, you can perform the following operations
on the DVD recorder and DVD player.
3:
Start playback.
To operate the DVD
player, set the mode
selector to “DVD.”
7:
Stop playback.
8:
Pause playback. To release it, press 3.
¢:
Skip to the beginning of the next
chapter.
4:
Return to the beginning of the current
(or previous) chapter.
DVD MENU:
Display the menu recorded on discs.
After pressing DVR/DVD or DVD MENU, you can perform the
following operations on the DVD recorder and DVD player.
5/∞/3/2:
Select an item on the menu screen.
SET:
Enter the selected item, channel
number, chapter/title number, or track
number (if required).
After setting the mode selector correctly, you can perform the
following operations on the DVD recorder or DVD player.
See the instructions supplied with the DVD recorder or DVD
player for details.
Only for DVD recorder operations:
CHANNEL +/–:
Change the channel numbers.
7 Changing the remote control code for DVD
recorder
1 – 9, 0:
Select a channel number (while stopped)
or a chapter/title number, track number
(while playing back). Press SET to enter
the number.
Some JVC DVD recorders can accept four types of the control
signals. You can assign one of four codes to the remote
control supplied with this receiver for operating your DVD
recorder. For details, refer to the manual supplied with the
DVD recorder.
+ 3:
Start recording.
+ 8:
Enter recording pause. To start recording,
press 3.
Initial setting: 03
1 Set the mode selector to “DVR.”
Only for DVD player operations:
1 – 10, 0, +10:
2 Press and hold DVR/DVD
.
Select a chapter/title number, track
number, menu item, etc.
3 Press DVR/DVD.
4 Enter the remote control code you want using
buttons 1 – 4, and 0.
EX.: To enter the code “2”, press 0, then 2.
Code for DVR
Number to enter
1
2
3
4
01
02
03
04
5 Release DVR/DVD
If these buttons do not function normally, use the remote
control supplied with your DVD recorder or DVD player.
Refer also to the manuals supplied with the DVD recorder
or DVD player for details.
.
Now, the remote control code has been changed.
49
48-52RX-D702B[J].p65
49
05.8.25, 1:05 PM
Manufacturers’ codes for TV
Operating other
manufacturers’
products
By changing the transmittable signals, you can use the
supplied remote control to operate other manufacturers’
products.
• Refer also to the manuals supplied with the other products.
• To operate those components with the remote control, first you
need to set the manufacturers’ codes each for the TV, VCR,
CATV converter, DBS tuner, and DVD player.
• After replacing batteries of the remote control, set the
manufacturers’ codes again.
• All the functions may not be assigned to the buttons in some
equipment.
❏ Changing the transmittable signals for operating
a TV
1 Press and hold TV/SIRIUS
.
2 Press TV.
3 Enter the manufacturer’s code using buttons
1 – 9, and 0.
See “Manufacturers’ codes for TV” on the right.
4 Release TV/SIRIUS
.
Now, you can perform the following operations on the TV.
TV VOL +/–:
Adjust the volume on the TV.
TV/VIDEO:
Change the input mode (either TV or
VIDEO).
After pressing TV, you can perform the following operations on
the TV.
TV/SIRIUS
:
Manufacturer
JVC
Akai
Bell+Howell
Centurion
Coronad
Daewoo
Emerson
Fisher
GE•Pana
GE•RCA
Gold Star
Hitachi
KTV
Magnavox
Marantz
Mitsubishi
Panasonic
Philips
Pioneer
Proscan
Quasar
Radioshack
RCA
Samsung
Sanyo
Sears
Sharp
Sony
Symphonic
Toshiba
Zenith
Codes
01
02
03
04
05
06, 07, 08
09, 10, 11, 12, 13
14
15, 16
17
18, 19
20, 21
22, 23
24
25
25
26, 27
24
28
29
30
31
02, 17, 32, 33, 34, 35
36, 37
14
38
39
40
41, 42
38
43, 44
Initial setting: 01
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
Turn on or off the TV.
CHANNEL +/–:
Change the channel numbers.
1 – 9, 0, 100+ (+10):
Select the channel numbers.
See the instructions supplied with the TV for details.
5 Try to operate your TV by pressing TV/SIRIUS
.
When your TV turns on or off, you have entered the correct
code.
If more than one code is listed for your brand of TV, try each
one until the correct one is entered.
50
48-52RX-D702B[J].p65
50
05.8.25, 1:05 PM
❏ Changing the transmittable signals for operating
a VCR
1 Press and hold VCR
Manufacturer
.
2 Press VCR.
3 Enter the manufacturer’s code using buttons
1 – 9, and 0.
See “Manufacturers’ codes for VCR” on the right.
4 Release VCR
.
Now, you can perform the following operation on the VCR.
VCR
:
Turn on or off the VCR.
After pressing VCR, you can perform the following operations
on the VCR.
CHANNEL +/–:
Change the channel numbers on the
VCR.
1 – 10, 0, +10:
Select the channel numbers on the VCR.
3:
Start playback.
7:
Stop playback.
8:
Pause playback.
FF:
Fast-wind a tape.
REW:
Rewind a tape.
+ 3:
Start recording.
+ 8:
Enter recording pause. To start
recording, press this button then 3.
Manufacturers’ codes for VCR
JVC
Aiwa
Akai
Bell+Howell
Daewoo
Emerson
Fisher
G.E.
Go Video
Gold Star
Go-Video A
Go-Video B
Hitachi
Magnavox
Mitsubishi
NEC
Panasonic
Philips
RCA
Samsung
Sanyo
Scott
Sharp
Shintom
Sony
Symphonic
Teknica
Toshiba
Zenith
Codes
01, 02, 03, 04
05
06, 07, 08
09
10
11, 12, 13, 14, 15
16, 17, 18, 19
20, 21
22
23
24
25
20, 26
27, 28, 29
30, 31, 32, 33
34, 35
36, 37
27
38
39, 40, 41
16, 17, 18, 19
42
43, 44
45
46, 47, 48, 49, 50, 51
52
53, 54
55
56
See the instructions supplied with the VCR for details.
Initial setting: 01
5 Try to operate your VCR by pressing VCR
.
When your VCR turns on or off, you have entered the correct
code.
If more than one code is listed for your brand of VCR, try each
one until the correct one is entered.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
51
48-52RX-D702B[J].p65
51
05.8.25, 1:05 PM
❏ Changing the transmittable signals for operating
a CATV converter or DBS tuner
❏ Changing the transmittable signals for operating
a DVD player
1 Press and hold DBS/CATV
1
2
3
4
.
2 Press DBS.
3 Enter the manufacturer’s code using buttons
1 – 9, and 0.
See “Manufacturers’ codes for CATV converter” or
“Manufacturers’ codes for DBS tuner” below.
4 Release DBS/CATV
.
Now, you can perform the following operation on the CATV
converter or DBS tuner.
Set the mode selector to “DVD.”
Press and hold DVR/DVD .
Press DVR/DVD.
Enter the manufacturer’s code using buttons
1 – 9, and 0.
See “Manufacturers’ codes for DVD player” below.
5 Release DVR/DVD
.
Now, you can perform the following operation on the DVD
player.
DVR/DVD
:
Turn on or off the DVD player.
3:
Start playback.
4:
After pressing DBS, you can perform the following operations
on the CATV converter or DBS tuner.
Return to the beginning of the current
chapter (or fast-forward for some
models).
¢:
Skip to the beginning of the next chapter
(or fast-reverse for some models).
CHANNEL +/–:
7:
Stop playback.
8:
Pause playback.
DVD MENU:
Display the menu recorded on DVD
VIDEO discs.
1 – 9, 0, +10:
Select the chapter number.
DBS/CATV
:
Turn on or off the CATV converter or
DBS tuner.
Change the channel numbers on the
CATV converter or DBS tuner.
1 – 10, 0, 100+ (+10):
Select the channel numbers on the
CATV converter or DBS tuner.
See the instructions supplied with the CATV converter or DBS
tuner for details.
5 Try to operate your CATV converter or DBS
tuner by pressing DBS/CATV
.
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If more than one code is listed for your brand of CATV
converter or DBS tuner, try each one until the correct one is
entered.
Manufacturers’ codes for CATV converter
Manufacturer
G.I.
Gemini
Hamlin
Jerrold
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
S. Atlanta
Samsung
Tocom
Zenith
5/∞/3/2:
Select an item on the menu screen.
SET:
Enter the selected item.
See the instructions supplied with the DVD player for details.
6 Try to operate your DVD player by pressing
DVR/DVD
01
02
03, 04, 05, 06
07, 08, 09, 10, 11, 12, 13, 14, 15
16, 17, 18
19
20, 21, 22
23, 24
25, 26, 27, 28, 29, 30
31, 32
33, 34, 35
36
37
38, 39
Manufacturer
Codes
40
41
42
43
44
45
46
47
48
Initial setting: 40
.
When your DVD player turns on or off, you have entered the
correct code.
Manufacturers’ codes for DVD player
Codes
Manufacturers’ codes for DBS tuner
Echostar
G.I.
Hitachi
Hughes
Panasonic
Primestar
RCA
Sony
Toshiba
After pressing DVR/DVD or DVD MENU, you can perform the
following operations on the DVD recorder and DVD player.
Manufacturer
JVC
Hitachi
Kenwood
Magnavox
Marantz
Mitsubishi
Onkyo
Panasonic
Philips
Pioneer
Proscan
RCA
Samsung
Sony
Toshiba
Yamaha
Zenith
Codes
01
02
03, 04
05
06
07
08, 09
10
06
11
12
12
13
14
05
15
05, 16
Initial setting: 01
If more than one code is listed for your brand of DVD player,
try each one until the correct one is entered.
NOTE
You cannot use this remote control to operate other
manufacturers’ DVD recorder.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
52
48-52RX-D702B[J].p65
52
05.8.25, 1:05 PM
Troubleshooting
Use this chart to help you solve daily operational problems. If
there are any problems you cannot solve, contact your JVC’s
service center.
PROBLEM
The power does not come on.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
The receiver turns off (enters standby
mode).
Speakers are overloaded because of high
volume.
1. Stop the playback source.
2. Turn on the receiver again, then turn the
volume down.
Speakers are overloaded because of a
short circuit at the speaker terminals.
Check the speaker wiring. If speaker wiring
is not short-circuited, contact your dealer.
The receiver is overloaded because of a
high voltage.
Consult your dealer after unplugging the
power cord.
“OVER HEAT” flashes on the display,
then the receiver turns off.
The receiver is overloaded because of high
volume or long time usage.
Turn the volume down or turn off the
receiver for a while and turn it on again.
If the receiver turns off soon after doing
solutions above, consult your dealer after
unplugging the power cord.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring, then reconnect if
necessary (see page 8) after unplugging
the power cord.
Connections are incorrect.
Check the audio connections (see pages
10 to 18) after unplugging the power cord.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute (see
page 21).
An incorrect audio input setting (analog or
digital) is selected.
Select the correct audio input setting
(analog or digital).
Sound from one speaker only.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary (see page 8) after unplugging
the power cord.
Sounds are intermittently distorted by
the outside noise such as a lightning
discharge.
When you use the digital coaxial connection,
the sounds may be intermittently distorted
by the outside noise such as a lightning
discharge but the sound will be restored
automatically.
This is not a malfunction.
No picture on the TV screen.
Either the video input setting or video
output setting is incorrect.
Select the correct setting (see page 20 or
32).
No picture on the TV screen when
“VCR” or “DBS” is selected as the
source.
Either “HDMI SELECT” or “CMPNT
SELECT” (see page 32) is not assigned for
each source correctly.
Select the correct setting.
On-screen display does not appear on
the TV screen.
The video input setting is set to “HDMI.”
Set the video input setting to the setting
other than “HDMI.” (see page 20)
HDMI signals do not come on.
A video or audio format not compatible with
this receiver and/or TV is played.
Check the video or audio format of the
signal to see if it is compatible with this
receiver and/or TV.
A HDCP-compatible TV is not connected.
Connect a HDCP-compatible TV (see page
10).
The receiver failed to recognize HDMIconnected components.
Disconnect the HDMI cable and connect it
again.
A HDMI cable longer than 5 m (15 ft) is
used.
Use a HDMI cable shorter than 5 m (15 ft)
to assure stable operation and picture
quality.
Power
Sound and picture
SOLUTION
POSSIBLE CAUSE
CONTINUED ON THE NEXT PAGE
53
53-55RX-D702B[J]_f.p65
53
05.8.25, 1:06 PM
Remote control
PROBLEM
POSSIBLE CAUSE
SOLUTION
Remote control does not operate as
you intend.
The remote control is not ready for your
intended operation.
Set the mode selector correctly, then press
the corresponding source selecting button
before operation.
Remote control does not work.
There is an obstruction hiding the remote
sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
The mode selector is set to the incorrect
position.
Set the mode selector to the proper
position.
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select another station.
The wrong antenna is being used.
Check with your dealer to be sure you have
the correct antenna.
Antennas are not connected properly.
Check the connections.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
Tuner
Continuous hiss or buzzing during FM
reception.
Occasional cracking noise during FM
reception.
54
53-55RX-D702B[J]_f.p65
54
05.8.25, 1:06 PM
Video
Specifications
Video Input Sensitivity/Impedance:
Composite video: DVR/DVD, VCR, DBS:
1 V(p-p)/75 Ω
S-video: DVR/DVD, VCR, DBS:
Y (luminance):
1 V(p-p)/75 Ω
C (chrominance, burst):
0.286 V(p-p)/75 Ω
Component: DVR/DVD, VCR (DBS):
Designs and specifications are subject to change without
notice.
Y (luminance):
1 V(p-p)/75 Ω
PB, PR:
0.7 V(p-p)/75 Ω
Video Output Level/Impedance:
Composite video: DVR, VCR, MONITOR OUT:
1 V(p-p)/75 Ω
S-video: DVR, VCR, MONITOR OUT:
Amplifier
Output Power
1 V(p-p)/75 Ω
0.286 V(p-p)/75 Ω
Component: MONITOR OUT:
At stereo operation:
Front channels:
Y (luminance):
C (chrominance, burst):
150 W per channel, min. RMS, driven
into 6 Ω at 20Hz to 20 kHz with no
more than 0.8% total harmonic
distortion.
Y (luminance):
1 V(p-p)/75 Ω
PB, PR:
0.7 V(p-p)/75 Ω
Synchronization:
Negative
At surround operation:
Front channels:
150 W per channel, min. RMS, driven into
6 Ω at 1 kHz with no more than 0.8% total
harmonic distortion.
HDMI
Center channel:
150 W, min. RMS, driven into 6 Ω at 1 kHz,
with no more than 0.8% total harmonic
distortion.
HDMI Output (Ver. 1.0): MONITOR OUT
Surround channels: 150 W per channel, min. RMS, driven into
6 Ω at 1 kHz, with no more than 0.8%
total harmonic distortion.
Surround back channels:
150 W per channel, min. RMS, driven into
6 Ω at 1 kHz, with no more than 0.8% total
harmonic distortion.
HDMI Input (Ver. 1.1):
VCR (DBS), DVR/DVD
FM tuner (IHF)
Tuning Range:
87.5 MHz to 108.0 MHz
Usable Sensitivity:
12.8 dBf (1.2 µV/75 Ω)
Monaural:
50 dB Quieting Sensitivity:
Monaural:
16.0 dBf (1.7 µV/75 Ω)
Stereo:
37.5 dBf (20.5 µV/75 Ω)
Stereo Separation at REC OUT:
Audio
35 dB at 1 kHz
Audio Input Sensitivity/Impedance:
DVR/DVD, VCR, DBS, TV:
330 mV/47 kΩ
Audio Input (DIGITAL IN)*:
AM tuner
Tuning Range:
Coaxial: DIGITAL IN 1(DVR/DVD):
0.5 V(p-p)/75 Ω
Optical: DIGITAL IN 2(DBS), 3(VCR):
–21 dBm to –15 dBm
(660 nm ±30 nm)
530 kHz to 1 710 kHz
General
Power Requirements:
AC 120 V
Power Consumption:
195 W (at operation)
USB: USB WIRELESS
, 60 Hz
1.0 W (in standby mode)
USB TERMINAL
Dimensions (W x H x D): 435 mm x 91.5 mm x 371 mm
* Corresponding to Linear PCM, Dolby Digital, and DTS (with
sampling frequency—32 kHz, 44.1 kHz, 48 kHz).
(17 3/16 inches x 3 5/8 inches x 14 5/8 inches)
Mass:
7.8 kg (17.2 lbs)
Audio Output Level:
DVR, VCR:
330 mV
Signal-to-Noise Ratio (’66 IHF/’78 IHF): 80 dB/62 dB
Frequency Response (6 Ω):
20 Hz to 20 kHz (±1 dB)
Bass Boost:
+4 dB ±1 dB at 100 Hz
Equalization (at DSP operation):
Center frequency:
63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz
Control range:
±8 dB
USB WIRELESS SYSTEM
The USB wireless transmitter supplied with this receiver supports
Direct Sequence Spreading Spectrum (DSSS) using 2.4 GHz
frequency band.
55
53-55RX-D702B[J]_f.p65
55
05.8.25, 1:06 PM
warranty.p65
1
05.8.25, 1:20 PM
warranty.p65
2
05.8.25, 1:20 PM
RX-D702B
AUDIO / VIDEO CONTROL RECEIVER
EN
© 2005 Victor Company of Japan, Limited
cover_RX-D702B[J]_f.p65
2
0805RYMMDWJEIN
05.8.25, 1:20 PM
Download PDF