Quadra-Fire | 2100 Millennium | Operating instructions | Quadra-Fire 2100 Millennium Operating instructions

R
2100 MILLENNIUM WOOD STOVE
Advanced Combustion Technology (ACT)
Tested and
Listed by
C
O-T L
Beaverton
Oregon USA
OMNI-Test Laboratories, Inc.
This manual contains instructions for Installation, Operation & Maintenance. Please read this entire manual
before you install and use your new room heater. Failure to follow instructions may result in property
damage, bodily injury, or even death.
IMPORTANT SAFETY NOTES:
1) When installing your stove, particular attention should be paid to fire protection. If this room heater is not properly installed,
a house fire may result. To reduce the risk of fire, follow the installation instructions. Contact local building, fire officials
or authority having jurisdiction about restrictions, installation inspection and permit requirements in your area.
2) CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or
“freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.
3) During operation, if any part of the stove starts to glow, the stove is in an overfired condition. Close the air controls
completely by pulling them out, until the glowing has stopped. OVERFIRING VOIDS YOUR WARRANTY!
4) Cool ashes should be disposed of carefully, using a metal container.
5) Do not burn wet or green wood. Store wood in a dry location.
6) DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not
burn treated wood, or wood with salt (driftwood, etc.). Burning materials other than wood (including charcoal) under
adverse conditions may generate carbon monoxide in the home, resulting in illness or possible death.
7) Do not permit creosote or soot to accumulate excessively in the chimney or inside the firebox.
8) Check your chimney system thoroughly when installing into an existing metal or masonry chimney. Seek professional
advice if in doubt about its condition.
9) Do not connect this unit to a chimnney flue already serving another appliance.
10) Comply with all minimum clearances to combustibles as shown in this manual for this appliance.
11) Build fire on brick firebox floor. Do not use grates, andirons or other methods to support fuel.
12) HOT WHILE IN OPERATION! Keep children, pets, clothing and furniture away. Contact can cause skin burns.
13) Do not connect to any air distribution duct or system.
14) RISK OF FIRE! Do not operate with stove door or ash removal system door open.
15) For further information refer to NFPA 211 (US) or CAN/CSA-B365 (Canada).
16) Do not operate without fully assembling all components. Burning your stove wthout the legs attached (if supplied with
unit) will void your warranty, and could present a serious safety hazard.
17) Do not operate with broken glass.
PRIOR TO FIRST FIRE: Remove all labels from glass. Clean all plated surfaces with a glass cleanser and soft cloth to
prevent staining from fingerprint oils. See page 20 for details.
1445 North Highway
Colville, WA 99114
SAVE THESE INSTRUCTIONS
Part 250-6931C
November 3 2004
www.quadrafire.com
2100 ACT Millennium Wood Stove
R
Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and performance.
This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make
products that will satisfy your needs. Our Research and Development facility then employs the world’s most advanced
technology to achieve the optimum operation of our stoves, inserts and fireplaces. And yet we are old-fashioned when it
comes to craftsmanship. Each unit is meticulously fabricated and gold surfaces are hand-finished for lasting beauty and
enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspection. Additionally, we feel
it is important to offer you several finishing options and accessories to complement your home’s décor, individualize the
use of your appliance, and provide financial options in acquiring a quality hearth appliance. Ask your Quadra-Fire Dealer
for information on these options. From design, to fabrication, to shipping: Our guarantee of quality is more than a word, it’s
Quadra-Fire tradition, and we proudly back this tradition with a Limited Lifetime Warranty.
Prior to installation, we ask you to take a few moments to read this manual. It has been our experience that your
overall enjoyment of your new appliance will be greatly enhanced by becoming familiar with its installation, operation
and maintenance. We wish you and your family many years of enjoyment in the warmth and comfort of your hearth
appliance. Thank you for choosing Quadra-Fire.
With warm regards,
���������������������������
Alan Trusler
Senior Vice President
Dealer Channel
���������������������������
Dan Henry
Vice President
Research & Development
���������������������������
Mike Derosier
Vice President
Marketing & Product Planning
Page 2
_________________________
Jason Olmstead
Vice President &
General Manager
Dave Fiebelkorn
Materials Manager
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
TABLE OF CONTENTS
MODEL NAME
QUADRA-FIRE 2100
MILLENNIUM WOOD STOVE
Serial Number
Date Purchased
Dealership Where Purchased
Dealer Phone
Listings & Safety Cautions .................................. 4
Installation Materials Needed .............................. 4
Venting System Overview ................................... 4
Dimensions .......................................................... 5
Vent Specifications .............................................. 5
Serial Number Label Location ............................. 5
Locating Your Stove ............................................ 5
Clearances to Combustibles ............................... 6
Floor Protection ................................................... 7
INSTALLATION METHODS:
Chimney Height / Draft & 2-10-3 Rule ................. 8
Flue Systems & Chimney Connections ............... 9
Masonry Chimney ............................................... 10
Solid Pack with Metal Supports ........................... 10-11
Metal Pre-Fab Chimney ...................................... 12
Mobile Home ....................................................... 13
OPERATING INSTRUCTIONS:
The Burning Process ........................................... 15
Start-Up & Primary Air Systems .......................... 15
Operating Instructions ......................................... 16
Burning Guidelines .............................................. 16
Building a Fire ..................................................... 16
Opacity ................................................................ 17
Burn Rates .......................................................... 17
Wood Selection ................................................... 17
Blower Operation ................................................. 17
Additional Information:
After completing your warranty card, attach your sales receipt
and warranty stub here for future reference.
NOTICE!
When this heater is not properly installed, a house
fire may result. To reduce the risk of fire, follow the
installation instructions. Contact local building or fire
officials about restrictions and installation inspection
requirements in your area. Please read this entire
manual before you install and use your new room
heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
250-6931C November 3, 2004
MAINTENANCE:
Creosote Removal ............................................... 18
Chimney Cleaning ............................................... 18
Firebrick .............................................................. 18
Overfiring ............................................................. 18
Ash Disposal ...................................................... 18
Glass Care & Cleaning ........................................ 18
Plated Surfaces ................................................... 18
ACCESSSORY / PARTS REPLACEMENT
Outside Air Kit ...................................................... 14
Brick Replacement .............................................. 19
Blower Installation and Operation ....................... 19
Door Handle Assembly ........................................ 20
Glass Replacement ............................................. 20
Baffle Removal & Installation .............................. 20
Exploded View ..................................................... 21
Accessory & Replacement Parts List .................. 22
Warranty Policy ................................................... 23
Page 3
R
2100 ACT Millennium Wood Stove
LISTINGS & SAFETY CAUTIONS
These installation instructions describe the installation and
operation of the QUADRA-FIRE 2100 Millennium woodstove.
This stove meets the U.S. Environmental Protection Agency’s
1990 particulate emission standards. The 2100 Millenium is
listed by OMNI-Test Laboratories, Inc. to UL Safety Standard
1482, and ULC S627, and (UM) 84-HUD. The 2100 Millennium
is approved for mobile home installations when not installed
in a sleeping room and when an outside combustion air inlet
is provided. The structural integrity of the mobile home floor,
ceiling, and walls must be maintained. The stove must be
properly grounded to the frame of the mobile home and use only
listed double-wall connector pipe. Outside Air Kit, part 831-1780
must be installed in a mobile home installation.
Check with your local building code agency before you begin
your installation to ensure compliance with local codes, including
the need for permits and follow-up inspections. Be sure local
building codes do not supersede UL specifications and always
obtain a building permit so that insurance protection benefits
cannot be unexpectedly cancelled. If any assistance is required
during installation, please contact your local dealer.
Inspect and clean vent system frequently in accordance with the
instructions contained in this manual. Do not connect this unit
to a chimney serving another appliance.
When using optional Blower, part 831-1701, route power cord
away from unit. Do not route cord under or in front of appliance.
Do not elevate fire. Build wood fire directly on firebrick.
Do not overfire - if heater or chimney connector glows, you are
overfiring. Stove thermometer recommended.
Operate only with the door closed. Open only to add fuel to
the fire. Operating with the door open can cause hot embers or
sparks to fall out and a fire may result.
INSTALLATION MATERIALS NEEDED FOR SAFETY
CHIMNEY CONNECTOR (also known as flue pipe or stove
pipe): The chimney connector joins the stove to the chimney
(see page 9). It must be 6” (152mm) minimum diameter 24
MSG black or blued steel, or an approved air-insulated double
wall venting pipe.
FIRE SAFETY: To provide reasonable fire safety, the following should
be given serious consideration:
1. Install at least one smoke detector on each floor of your home
to ensure your safety. They should be located away from the
heating appliance and close to the sleeping areas. Follow
the smoke detector manufacturer’s placement and installation
instructions, and be sure to maintain regularly.
2.
A conveniently located Class A fire extinguisher to contend with
small fires resulting from burning embers.
3.
A practiced evacuation plan, consisting of at least two escape
routes.
4.
A plan to deal with a chimney fire as follows:
In the event of a chimney fire:
A.
B.
C.
D.
Notify fire department
Prepare occupants for immediate evacuation.
Close all openings into the stove.
While awaiting fire department, watch for ignition of
adjacent combustibles from overheated stove pipe, hot
embers or sparks from the chimney.
VENTING SYSTEM
The venting system consists of a chimney connector and a chimney.
These get extremely hot during use. Temperatures inside the
chimney may exceed 2000°F (1100°C) in the event of a creosote
fire. To protect against the possibility of a house fire, the chimney
connector and chimney must be properly installed and maintained.
An approved thimble must be used when a connection is made
through a combustible wall to a chimney. A chimney support package
must be used when a connection is made through the ceiling
to a prefabricated chimney. These accessories are absolutely
necessary to provide safe clearances to combustible wall and ceiling
material. Follow venting manufacturer’s clearances when installing
venting system.
This stove may be connected to a lined masonry chimney or a listed
high temperature prefabricated approved metal chimney. Do not
connect it to a chimney serving another appliance. To do so will
affect the safe operation of both appliances.
THIMBLE: A manufactured or site-constructed device installed in
combustible walls through which the chimney connector passes
to the chimney (see pages 10-11). It is intended to keep the
walls from igniting.
WARNING! NEVER DRAW OUTSIDE COMBUSTION AIR FROM A
WALL, FLOOR OR CEILING CAVITY OR FROM ANY ENCLOSED
SPACE SUCH AS AN ATTIC OR GARAGE.
CHIMNEY SYSTEMS:
WARNING! DO NOT ATTEMPT TO OPERATE THIS WOODSTOVE
WITHOUT READING AND UNDERSTANDING THESE OPERATING INSTRUCTIONS THOROUGHLY. FAILURE TO OPERATE
THIS APPLIANCE PROPERLY MAY CAUSE A HOUSE FIRE.
A. APPROVED MASONRY (see specifications on page 9) with
at least 5/8” (16mm) fire clay lining joined with refractory
cement or other listed system suitable for use with wood
stoves.
B. PREFABRICATED 6" (152mm) listed high temperature (UL
103 HT or ULC S629M) chimney. Components required by
manufacturers for installation such as the chimney support
base, firestop (as appropriate), attic insulation shield,
insulated tee, etc., are necessary to assure a safe chimney
installation. Use only components manufactured for the
chimney. Chimney installation should meet NFPA 211
standards.
Page 4
WARNING! THIS APPLIANCE IS HOT WHILE IN OPERATION
AND MAY REMAIN SO UP TO 40 MINUTES AFTER THERE
IS NO FUEL IN THE FIREBOX. IF THIS APPLIANCE IS IN
A HIGH TRAFFIC AREA OR CHILDREN MAY BE NEAR IT
IS RECOMMENDED THAT YOU PURCHASE A DECORATIVE
BARRIOR TO GO IN FRONT OF THE APPLIANCE. ALWAYS
KEEP CHILDREN AWAY WHILE IT IS OPERATING AND DO NOT
LET ANYONE OPERATE THIS APPLIANCE UNLESS THEY ARE
FAMILIAR WITH THESE OPERATION INSTRUCTIONS.
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
DIMENSIONS
FRONT VIEW
SIDE VIEW
21-3/8" (543mm)
7-7/16"
(189mm)
CL
25-7/8" (657mm)
10-11/16"
(271mm)
23-1/16" (332mm)
5-3/8"
(137mm)
CL
13-5/8" (346mm)
17.0" (432mm)
12-3/4"
(324mm)
9-3/8"
(238mm)
Back of the stove to glass
22.0" (559mm)
26-1/2"
(673mm)
15-3/4" (400mm)
15-1/2" (393mm)
CL
3-3/8" (86mm)
SERIAL NUMBER LABEL LOCATION:
ON BACK OF STOVE
VENT SPECIFICATIONS
Single Wall: Six inch (6”) (152mm) diameter, minimum 24 MSG black or blued steel connector pipe, with a listed factory-built
chimney type UL103 HT* suitable for use with solid fuels, or a masonry chimney, and the referenced clearances.
Double Wall/Mobile Home: Six inch (6”) (152mm) diameter, listed double wall air insulated connector pipe with listed
factory-built UL103 HT* Class “A” chimney, or a masonry chimney (Mobile Home must be equipped with a spark arrestor),
and the referenced clearances. Use only double-wall connector pipe, Dura-Vent DVL, Selkirk metalbestos DS or Security
DL double wall connector. or any listed double-wall connector pipe.
*In Canada must comply with CAN/ULC-S269 for the 650°C Factory-built chimney.
LOCATING YOUR STOVE
WHEN LOCATING YOUR STOVE consider safety, convenience, traffic flow, and the fact that the stove will need a chimney
and chimney connector. It is a good idea to plan your installation on paper, using exact measurements for clearances and
floor protection, before actually beginning the installation. If you’re not using an existing chimney, place the stove where
there will be a clear passage for a factory-built listed chimney through the ceiling and roof.
AVOID FIRE: Maintain the designated clearances to combustibles. Insulation must not touch the chimney. You must maintain
the designated air space clearance around the chimney. This space around a chimney is necessary to allow natural heat
removal from the area. Insulation in this space will cause a heat buildup, which may ignite wood framing. NOTE: Clearances
may only be reduced by means approved by the regulatory authority having jurisdiction.
WE RECOMMEND that a qualified building inspector and your insurance company representative review your plans before
and after installation.
250-6931C November 3, 2004
Page 5
2100 ACT Millennium Wood Stove
R
CLEARANCES TO COMBUSTIBLES (UL AND ULC)
BACKWALL / SIDEWALL
A
ALCOVE SIDE VIEW
B
90° OFF TOP
UP & OUT CEILING
CLEARANCE
C
D
H
G
*
A
G
B
STOVE TO CEILING
CLEARANCE
CORNER INSTALLATION
ALCOVE TOP VIEW
E
F
C
E
D
F
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.
A
B
C
D
E
F
G
H
INSTALLATION: Full Vertical OR Horizontal with Minimum 2 Foot Vertical Off Stove Top
SINGLE WALL PIPE
16 (406) 13.5 (343) 19 (483) 11.5 (292)
9.5 (241) 17(432)
DOUBLE WALL PIPE
9 (229)
8 (203)
6 (152)
19 (483)
11 (279)
43 (1092) 18 (457)*
16 (406) 43 (1092)
5 (127)
INSTALLATION: 90° Elbow Off Top of Stove Through Backwall
SINGLE WALL PIPE
16 (406) 13.5 (343) 19 (483) 11.5 (292)
9.5 (241) 17 (432)
DOUBLE WALL PIPE
9 (228)
8 (203)
6 (152)
19 (483) 11 (279)
43 (1092)
16 (406) 43 (1092)
18 (457)*
5 (127)
INSTALLATION: ALCOVE
Six inch (6") (152mm) diameter listed double wall air insulated connector pipe with UL
103 HT listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark
arrestor). Maximum depth of alcove shall be no more than 48"(1220mm) with a minimum height of 43" (1092mm) to top
of unit, and the referenced clearances.
DOUBLE WALL PIPE
11.5 (292) 9.5 (241)
22 (559)
14 (356)
N/A
N/A
43 (1092)
**
* NPFA MINIMUM CLEARANCE - NOT TESTED
** SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED
Page 6
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
FLOOR PROTECTION
FLOOR PROTECTION: Floor protector must be noncombustible material, extending beneath heater and to the
front/sides/rear as indicated. The floor must be non-combustible or otherwise adequately protected from radiant
heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible
floor is not sufficient.
In US installations, it is necessary to install a floor protector of 3/8" thick metal clad millboard or equivalent at least 16"
(406mm) in front of glass door and 8" (203mm) to both sides of the fuel loading door. Open the door and measure 8”
(203mm) from the side edge of the opening in the face of the stove. See *exception below.
In Canada, similar floor protection must be provided 18" (457mm) in front and 8" (203mm) from the sides and rear
of the stove. See *exception below.
*EXCEPTION: Non-combustile floor protection must extend beneath the flue pipe when installed with horizontal venting
and extend 2” (51mm) beyond each side.
NOTE: Drawings are for illustration purposes only and are not to scale.
50-1/2"
io
3-5/8"
t
op
2
/8
5
9-
"
33-1/2"
4-3/8"
re
d
-1
/
8"
ui
"
24
USA
co
16
29-5/8"
minimum
38
re
q
o
co ptio
ve na
ra l
ge
USA
ve
"
8"
ra
g
e
38"
minimum
Fuel loading door
16" from glass
na
ge
o
co ptio
ve na
ra l
ge
ra
e
ov
lc
33-1/2"
203mm (8")
203mm
(8")
203mm
(8")
1248mm
(49-1/8")
minimum
457mm (18")
CANADA
940mm (37-3/8")
minimum
250-6931C November 3, 2004
Must extend 2" (51mm) beyond each
side of pipe (shaded area)
USA: REQUIRED
CANADA: RECOMMENDED
Page 7
R
2100 ACT Millennium Wood Stove
CHIMNEY HEIGHT/DRAFT
To be sure that your Quadra-Fire stove burns properly, the chimney draft (static pressure) should be approximately -.10”
water column (W.C.) during a high burn and -.04” W.C. during a low burn, measured 6” (152mm) above the top of the stove
after one hour of operation at each burn setting.
NOTE: These are guidelines only, and may vary somewhat for individual installations.
Your Quadra-Fire stove was designed for and tested on a 6” (152mm) chimney, 12’-14’ (360-420cm) high, (includes stove
height) measured from the base of the stove. The further your stack height or diameter varies from this configuration, the
possibility of performance problems exists. In addition, exterior conditions such as roof line, surrounding trees, prevailing
winds and nearby hills can influence stove performance. Your local dealer is the expert in your geographic area and can
usually make suggestions or discover solutions that will easily correct your flue problem, allowing your woodstove and its
flue system to operate correctly and provide safe and economical heat for your home.
A masonry chimney or a listed factory-built UL103 HT Class “A” chimney must be the required height above the roof and
any other nearby obstructions. The chimney must be at least 3’ (91cm) higher than the highest point where it passes
through the roof and at least 2’ (61cm) higher than the highest part of the roof or structure that is within 10’ (305cm) of the
chimney, measured horizontally. See 2-10-3 Rule below.
These are safety requirements and are not meant to assure proper flue draft.
We recommend using a minimum total system height of 12' (360cm), measured from the flue collar to the top of the
chimney (not including chimney cap).
Availability of combustion air: A source of air (oxygen) is necessary in order for combustion to take place. It is important
to realize that whatever combustion air is consumed by the fire must be replaced. If you are using room air, the air is
replaced via air leakage that occurs around windows and under doors, etc. However, in most newly constructed houses,
mobile homes, or even existing homes that are fitted with tightly sealed doors and windows, the area from which the
combustion air is taken is relatively air tight. In these cases, an outside air source must be made available to feed
combustion air from outside the home into the stove. An Outside Air Kit is available for your stove as an option, Part
831-1780. The kit is a requirement for mobile home installations. Check with the local authorities in your area for
the requirements in your location.
2-10-3 RULE
3 ft Min
(91cm)
2 ft Min (61cm)
10 ft Min
(305cm)
WARNING!
ALWAYS FOLLOW CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS FOR PROPER
INSTALLATION.
CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE AND
CEILING OR WALL. THE CONNECTOR SHALL NOT PASS THROUGH AN ATTIC OR ROOF SPACE,
CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING. MAINTAIN MINIMUM
CLEARANCES TO COMBUSTIBLES AS REFERENCED ON PAGES 9, 10, 11 & 12.
Page 8
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
FLUE SYSTEMS
There are two separate and different parts to a flue system: the
chimney connector and the chimney itself.
A.
B.
Single wall connector or stove pipe. This must be at least
24 gauge mild steel or 26 gauge blue steel. The sections
must be attached to the stove and to each other with
the crimped (male) end pointing toward the stove. See
Chimney Connector Diagram below. All joints, including
the connection at the stove collar, should be secured
with three sheet metal screws. Make sure to follow
the minimum clearances to combustibles as set out on
page 6 of this manual. Where passage through the wall,
or partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365 (Canada).
Factory-built listed chimney connector (vented). A listed
connector (vented) must be used when installing this unit
in a mobile home. The listed connectors must conform to
each other to ensure a proper fit and seal.
TOWARDS
STOVE
FLUE
GAS
DIRECTION
R
MASONRY CHIMNEY (Cont’d)
The flue should be checked to determine that it is not too
large for the stove. NFPA 211 allows the cross-sectional
area of the flue to be no more than 3 times the crosssectional area of the flue collar of the stove (28 x 3 =
84 square inches). It is recommended that a chimney
with a larger diameter than 6” (152mm) be relined,
since the oversized flue can cause poor performance
and contribute to the accumulation of creosote. (See
page 8 for more information about troubleshooting draft
problems).
CAUTION! DO NOT CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING ANOTHER APPLIANCE.
When connecting the stove through a combustible wall to
a masonry chimney, special methods are needed. There
are several ways to make this connection, including
the construction of a masonry thimble. In Canada, the
installation shall conform to CAN/CSA-B365. Check with
your local building authorities and/or consult the National
Fire Protection Association (NFPA 211). Refer to Figure
11B on page 11 and Figures 12A &12B on page 12
Wood Stud 2"
(51mm)
Clearance
from chimney
wall
Fireclay liner 5/8"
(16mm) Minimum
or Equivalent.
Header
FIGURE 9A - Chimney Connector
MASONRY CHIMNEY
For optimal performance, masonry chimneys used to vent this
appliance should be lined with a 6" (152mm) stainless steel
liner. Installations into a clay flue without a stainless steel liner
may reduce draw which affects performance, cause the glass
to darken and produce excessive creosote.
Ensure that a masonry chimney meets the minimum standards
of the National Fire Protection Association (NFPA) Standard
211. It must have at least a 5/8" (16mm) fire clay liner or a
listed chimney liner system. See Figure 9B. Make sure there
are no cracks, loose mortar or other signs of deterioration
and blockage. It is best to have the chimney inspected by a
professional, and be sure to have the chimney cleaned before
the stove is installed and operated.
Fireclay liner 5/8"
(16mm) Minimum
or Equivalent.
Sill support
Thimble Assembly:
12" (305mm) of brick
separation between
clay liner and
combustibles.
FIGURE 9B
WARNING!! IF INSTALLING THIS MODEL TO A MASONRY CHIMNEY, ALWAYS BE SURE THE CHIMNEY IS IN GOOD
CONDITION AND THAT IT MEETS THE MINIMUM STANDARDS OF THE NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
STANDARD 211. A FACTORY BUILT CHIMNEY MUST BE 6” (152mm) UL103 HT.
THIS APPLIANCE IS MADE WITH A 6 INCH (152mm) DIAMETER CHIMNEY CONNECTOR AS THE FLUE COLLAR ON THE
UNIT. CHANGING THE DIAMETER OF THE CHIMNEY CAN AFFECT DRAFT AND CAUSE POOR PERFORMANCE. IT IS NOT
RECOMMENDED TO USE OFFSETS OR ELBOWS AT ALTITUDES ABOVE 4000 FEET ABOVE SEA LEVEL OR WHEN THERE
ARE OTHER FACTORS THAT AFFECT FLUE DRAFT.
250-6931C November 3, 2004
Page 9
2100 ACT Millennium Wood Stove
R
SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE
For the method of installation to a masonry chimney shown in Figures 12A & 12B on page 12, it will be necessary to
purchase a 12” (305mm) long 8" (203mm) inside diameter, section of prefabricated listed solid pack chimney to use as a
thimble. Purchase a wall spacer, trim collar, and a wall band manufactured to fit the chimney section you purchase.
The safety features of this system are twofold: 1) A 2" (51 mm) air space between the chimney section and combustible
wall; and, 2) The 1" (25mm) air space around the chimney connector as it passes through the chimney section to
the chimney.
The location of the opening through the wall to the chimney must leave a minimum 18" (457mm) vertical clearance
between the connector pipe and the ceiling (or minimum recommended from pipe manufacturer) to prevent the
ceiling from catching fire.
Measure for the center-line as shown in Figure 10A below. Cut an opening in the wall large enough to accommodate the
outside dimension of the chimney section plus the minimum air space specified by its manufacturer. It may be necessary
to cut the wall studs and install a header and a sill frame to maintain the wall support. The hole in the chimney must have
at least an 8" (203mm) diameter fire clay liner or equivalent, secured with refractory mortar. If it is necessary to cut a hole
in the chimney liner, use extreme care to keep it from shattering.
FIGURE 10B
FIGURE 10A
Wall
Opening
FIRECLAY FLUE
LINER WITH AIR
SPACE
CONCRETE CAP
RAFTER
Center of Hole
Center Line
Center Line
1" (25mm) CLEARANCE
WITH FIRESTOP
CEILING
JOIST
FLASHING
EAVE
COMBUSTIBLE
1" (25mm)
CLEARANCE
THIMBLE,
12" (305mm)
OF BRICK
Add center-line measurement to
depth measurement of your floor
protector. Mark this combined measurement at correct wall location
for your installation, maintaining
minimum clearance to combustibles,
and mark wall for a 10" x 10" (254mm
x 254mm) square hole.
SHEATHING
FLOOR
PROTECTOR
AIRTIGHT
CLEANOUT DOOR
WARNING! ALWAYS FOLLOW CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS FOR PROPER INSTALLATION.
CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE AND CEILING OR WALL, NEVER
PASSING THROUGH A COMBUSTIBLE CEILING OR WALL. THE CONNECTOR SHALL NOT PASS THROUGH AN ATTIC OR
ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING. MAINTAIN MINIMUM CLEARANCES
TO COMBUSTIBLES AS REFERENCED ON PAGE 6.
Page 10
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE (Cont’d)
First, make the frame for the thimble, ensuring it is
no smaller than 14" (368mm) square, to maintain a 2"
(51mm) air space around the chimney section.
Attach the wall spacer to the chimney side of the frame.
Then insert the frame into the opening, toe nailing it to
the wall studs. Install the wall band in the framing to
secure the chimney section in place.
Insert a single section of chimney connector into the
chimney through the wall band, being sure it does
not protrude into the chimney beyond the edge of the
chimney flue lining.
Apply high temperature furnace cement to the end of
the chimney section and install it over the connector,
through the wall spacer. Tighten the wall band to
hold the chimney section firmly in place and against
the chimney.
Min. Chimney Clearance
to Wall Spacer and
Combustibles - 2" (51mm)
Min. Clearance
2" (51mm)
1" (25mm) Air
Space to Chimney
Chimney Flue
Fireclay
Liner or
Equivalent
Chimney
Connector
Chimney Section
Trim Collar
Wall Band
Wall Spacer
Masonry Chimney
Constructed to NFPA 211
FIGURE 11A
Install the trim collar on the outside of the opening.
Check to make sure there is a 1" (25mm) air space
between the connector and the chimney section.
During installation be certain that a 2" (51mm) air space
to the wood framing is maintained. Do not fill this space
with insulation. Insulation in this air space will cause a
heat buildup which may ignite the wood framing.
Fire Clay
Flue Liner
Masonry
Trim Collar
Wall Spacer
Chimney Section
with 2" (51mm)
Clearance to
Combustibles
Wall Band to
Secure
Chimney
Connector
Wood Studs Used for
Framing - Spaced 2"
(51mm) clearance
from Masonry
FIGURE 11B
250-6931C November 3, 2004
Page 11
2100 ACT Millennium Wood Stove
R
CONNECTION TO A METAL PRE-FABRICATED CHIMNEY
When a metal prefabricated chimney is used,
the manufacturer’s installation instructions
must be followed precisely. You must also
purchase (from the same manufacturer) and
install the ceiling support package or wall passthrough and “T” section package, firestops
(where needed), insulation shield, roof flashing,
chimney cap, etc. Maintain the proper
clearance to the structure as recommended by
the manufacturer. This clearance is usually a
minimum of 2” (51mm), although it may vary by
manufacturer or for certain components.
There are basically two methods of metal
chimney installation. One method is to install
the chimney inside the residence through the
ceiling and the roof (Figure 12A). Install an
Maintain 2" (51mm)
Clearance
FOLLOW THE CHIMNEY MANUFACTURERS’
Specified
Clearance
Ceiling
Chimney
Connector
Listed Chimney
To Stove
Ceiling Support
Combustible Wall
Chimney
Connector
*
* Refer to Clearances
to Combustibles
*
Floor
Protector
an exterior chimney that runs up the outside
of the residence (Figure 12B). This method
of installation requires at a minimum a wall
pass-through device, a wall support package,
insulated “T” section and roof flashing. The
components illustrated may not look exactly like
the system you purchase, but they demonstrate
the basic components you will need for a
proper and safe installation.
IMPORTANT!
Storm Collar
Attic
Insulation
Shield
Combustible
Ceiling
Joists
Flashing
attic insulation shield to maintain the specified
clearance to insulation. Insulation in this air
space will cause a heat buildup which may ignite
the ceiling joists.The other method is to install
The chimney must be the required height
above the roof or other obstruction for safety
and proper draft operation. The chimney
must be a minimum of 3’ (91cm) higher than
the highest point where it passes through the
roof, and at least 2’ (61cm) higher than
the highest part of the roof or structure
that is within 10’ (305cm) of the chimney,
measured horizontally (2-10-3 Rule Figure
on page 8).
Listed
Chimney
Listed Cap
FIGURE 12A - INTERIOR CHIMNEY
Combustible Outside Wall
Maintain 2" (51mm)
Clearance Through Eave
Listed
Chimney Pipe
Listed Cap
2" (51mm)
Clearance
Chimney
Connector
Listed Chimney
Flashing
To Stove
Insulated " T "
Wall Support
Combustible
Ceiling
Trim Collar
on Inside
Wall
*
Wall Spacer on
Outside Wall
Insulated " T "
Chimney
Connector
*
Floor
Protector
*
Combustible Wall
*Refer to Clearances to Combustibles
INSTALLATION INSTRUCTIONS AND MAINTAIN
CLEARANCES AS SPECIFIED ON PAGE 7.
FIGURE 12B -EXTERIOR CHIMNEY
In Canada when using a factory-built chimney, make sure it is safety listed, Type UL 103 HT CLASS "A"
or conforming to CAN/ULC-S629, STANDARD FOR 650°C FACTORY-BUILT CHIMNEYS.
Page 12
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
MOBILE HOME INSTALLATION
1.
2.
3.
You must use a Quadra-Fire Outside Air Kit Part 831-1780 for installation in a mobile home.
An outside air inlet must be provided for combustion and must
remain clear of leaves, debris, ice and/or snow. It must be
unrestricted while unit is in use to prevent room air starvation
Spark Arestor Cap
which can cause smoke spillage and an inability to maintain a
fire. Smoke spillage can also set off smoke alarms.
Stove must be secured to the mobile home structure by bolting
pedestal through hearth pad and into floor.
Stove must be grounded with #8 solid copper grounding wire
or equivalent and terminated at each end with N.E.C. approved
grounding device.
4.
Stove must be installed with an approved UL103 HT ventilated
chimney connector, UL103 HT chimney, and terminal cap with
spark arrestor. Never use a single wall connector (stove
pipe) in a mobile home installation. Use only double-wall
connector pipe, Dura-Vent DVL, Selkirk metalbestos DS or
Security DL double-wall connector or any listed double-wall
connector pipe.
5.
Refer to page 6 of this manual or the Serial Number label on
the back of the stove for clearances to combustibles.
6.
7.
Storm Collar
Roof Flashing
Joist Shield/Firestop
Double wall
connector pipe
Outside Air
Rear Vent
Floor Protector
Floor protection requirements on page 7 must be followed
precisely.
In Canada, this appliance must be connected to a 6”
(152mm) factory-built chimney conforming to CAN/ULC629M, STANDARD FOR FACTORY BUILT CHIMNEYS. Floor
protection referenced on page 7 must be followed.
8.
Use silicone to create an effective vapor barrier at the location
where the chimney or other component penetrates to the
exterior of the structure.
9.
Follow the chimney and chimney connector manufacturer’s
instructions when installing the flue system for use in a
mobile home.
NOTE: Offsets from the vertical, not exceeding 45°, are allowed
per Section 905(a) of the Uniform Mechanical Code (UMC).
Offsets greater than 45° are considered horizontal and are
also allowed, providing the horizontal run does not exceed
75% of the vertical height of the vent. Construction, clearance
and termination must be in compliance with the UMC Table 9C.
This installation also complies with NFPA 211.
Outside Air Floor Vent
WARNING: NEVER DRAW COMBUSTION AIR FROM
A WALL, FLOOR OR CEILING CAVITY OR FROM
ANY ENCLOSED SPACE SUCH AS AN ATTIC OR
GARAGE.
CAUTION: THE STRUCTURAL INTEGRITY OF THE
MOBILE HOME FLOOR, WALL AND CEILING/ROOF
MUST BE MAINTAINED. (i.e., DO NOT CUT THROUGH
FLOOR JOIST, WALL STUD, CEILING TRUSS, ETC.)
WARNING: DO NOT INSTALL IN SLEEPING ROOM.
NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5 ft (411cm) from ground
level for transportation purposes.
10. Burn wood only. Other types of fuels may generate poisonous gases (e.g., carbon monoxide).
11. If unit burns poorly while an exhaust blower is on in home, (i.e., range hood), then increase combustion air.
250-6931C November 3, 2004
Page 13
2100 ACT Millennium Wood Stove
R
OUTSIDE AIR KIT INSTALLATION
Part 831-1780
Included in Kit: 1 front cover; fiberglass rope; 2 vent straps; venting flange & 4 screws; termination cap & screws. Discard
the 2 side covers and 1 rear cover as they are not needed for your Quadra-Fire 2100 Millennium.
Items Needed for Installation: 4” flex pipe in the length as required for your installation; Phillips screwdriver; Silicone
sealant; Drills and saws necessary for cutting holes through the wall or flooring in your home.
1. Remove all materials from packing box.
2. Using a #2 Phillips screwdriver, remove 2 bolts beneath the ashcatcher. Reuse bolts to install front cover. Be certain
that the cover is pushed back as far as possible.
3. Floor installation: Cut a 4” (102mm) minimum hole in the floor to accommodate outside air piping. Use 4” (102mm)
metal flex or rigid piping to directly connect outside air to the unit or into vented crawl space. (Do not put flex into a
non-vented crawl space). Use the supplied termination cap with a rodent screen. Seal between the floor and the pipe
with silicone to prevent moisture penetration. Install fiberglass sealing rope under each side of pedestal.
4. Rear/wall installation: Use the knockout plate in rear of the pedestal for exterior wall venting. Cut a 4” (102mm) hole in
outside wall to accommodate outside air piping. Use 4” (102mm) metal flex or rigid piping to directly connect outside air
to stove intake. Use the supplied termination cap with a rodent screen. Seal between the wall and the pipe with silicone
to prevent moisture penetration. Install fiberglass sealing rope under each side of pedestal.
FLEX FLANGE
(if needed for rear exit)
FRONT COVER
CL
3-3/8" (86mm)
FIBERGLASS SEALING ROPE
4" (102mm)
FLEX LINE
(Not Included)
Page 14
OUTSIDE AIR
TERMINATION CAP
(contains rodent screen)
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
OPERATING INSTRUCTIONS
IMPORTANT - PLEASE READ BEFORE USING STOVE
BURNING PROCESS
FINAL STAGE
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order
to improve the situation, we at Quadra-Fire have developed
cleaner-burning wood stoves that surpass the requirements
for emissions established by our governing agencies. These
wood stoves, like any other appliances, must be properly
operated in order to insure that they perform the way they are
designed to perform. Improper operation can turn most any
wood stove into a smoldering environmental hazard.
The final stage of burning is the charcoal stage. This
occurs when the flammable gases have been mostly
burned and only charcoal remains. This is a naturally
clean portion of the burn. The coals burn with hot blue
flames.
KINDLING or 1st STAGE
It helps to know a little about the actual process of burning
in order to understand what goes on inside a stove. The first
stage of burning is called the kindling stage. In this stage, the
wood is heated to a temperature high enough to evaporate
the moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat from
the coals and tends to cool the stove.
Fire requires three things to burn: fuel, air and heat. So, if
heat is robbed from the stove during the drying stage, the
new load of wood has reduced the chances for a good clean
burn. For this reason, it is always best to burn dry, seasoned
firewood. When the wood isn’t dry, you must open the air
controls and burn the stove at a high burn setting for a longer
time to start it burning. The heat generated from the fire
should be warming your home and establishing the flue draft,
not evaporating the moisutre out of wet, unserasoned wood,
resulting in wasted heat.
The air control in the center of the pedestal is called the
Start -Up Air Control; it is used during the kindling stage
of burning. It must be closed (pulled out) after the first 5
to 15 minutes.
It is very important to reload your stove while enough
lively hot coals remain in order to provide the amount of
heat needed to dry and rekindle the next load of wood.
It is best to open the air controls for a short while before
reloading. This livens up the coalbed. Open door
slowly so that ash or smoke does not exit stove through
opening. You should also break up any large chunks
and distribute the coals so that the new wood is laid
on hot coals.
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To
do this we need to learn to burn our stoves in the cleanest
way possible. Doing this will allow us to continue using
our wood stoves for many years to come.
AIR CONTROLS
START-UP AIR SYSTEM
The combustion air enters at the rear of the firebox
through the rear air tubes. This air supply is controlled
by the Start-up Air Control.
PRIMARY AIR SYSTEM
The primary air enters at the upper front of the firebox,
near the top of the glass door. This preheated air
supplies the necessary fresh oxygen to mix with the
unburned gases, helping to create secondary, tertiary
and quaternary combustions. This air is regulated by the
Primary Control. For more primary air push control in,
for less air pull control out.
2nd STAGE
The next stage of burning, the secondary stage, is the period
when the wood gives off flammable gases which burn above
the fuel with bright flames. During this stage of burning it is
very important that the flames be maintained and not allowed
to go out. This will ensure the cleanest possible fire. If you
are adjusting your stove for a low burn rate, you should close
down the air to the point where you can still maintain some
flame. If the flames tend to go out, the stove is set too low
for your burning conditions. The air control, immediately
beneath the ashcatcher, is the one used to adjust the stove
for burn rates. This is called the Primary Control. See
Figure 15A.
250-6931C November 3, 2004
PRIMARY AIR
CONTROL
START-UP AIR
CONTROL
FIGURE 15A
OPEN - PUSH IN Rod
CLOSE - PULL OUT Rod
Page 15
R
2100 ACT Millennium Wood Stove
OPERATING INSTRUCTIONS (Cont’d)
IMPORTANT - PLEASE READ BEFORE USING STOVE
For maximum operating efficiency with the lowest emissions, follow these operating procedures:
1.
2.
3.
4.
Regardless of desired heat output, when loading stove, burn your Quadra-Fire with both air controls wide
open for 5 to 15 minutes.
Regulate burn rate (heat output) by using the Primary Control (immediately under ashcatcher). The Start-Up
Air Control (in the center of the pedestal) is mainly for initial start-up and reloading.
Heat output settings: Following 5 to 15 minutes of burning with controls wide open (see #1 above):
Burn dry, well-seasoned wood.
BTU / Hr
Below 10,000
10,000 - 15,000
15,000 - 30,000
Maximum Heat
Start-Up Air Control
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
Closed after 5 to 15 minutes
*Primary Control
Pull to Stop
1” - 1-1/4” open
1-1/4” - 2” open
Fully open
*NOTE: These are approximate settings, and will vary with type of wood or chimney draft. Due
to altitude and other environmental circumstances, this operation information is a guideline only.
Similar burn rates may be obtained using other settings unique to your situation.
WARNING: Do not operate with Start-Up Air
Control in the open positionin excess of 15
minutes! Risk of extreme temperatures! Prolonged operation of this stove with the StartUp Air Control in the open position may cause
the combustible materials around the stove to
exceed safe temperature limits.
BUILDING A FIRE
CAUTION: Before lighting your first fire in the stove: 1) make certain that the baffle is correctly positioned.
It should be resting against the rear support; 2) Follow instructions on page 18 for cleaning plated surfaces,
and; 3) Remove all labels from glass.front.
CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start
or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.
There are many ways to build a fire. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning
kindling, which in turn ignites the slow-burning firewood. Here is one method that works well:
1.
Place several wads of crushed paper on the firebox floor. Heating the flue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
2.
3.
4.
Lay small dry sticks of kindling on top of the paper.
Open Start-Up Air Control and Primary Air Control fully.
Make sure that no matches or other combustibles are in the immediate area of the stove. Be sure the room is adequately
ventilated and the flue unobstructed.
Light the paper in the stove. NEVER light or rekindle stove with kerosene, gasoline, or charcoal lighter fluid; the
results can be fatal.
Once the kindling is burning quickly, add several full-length logs 3” (76mm) or 4” (102mm) in diameter. Be careful not
to smother the fire. Stack the pieces of wood carefully: near enough to keep each other hot, but far enough away from
each other to allow adequate air flow between them.
When ready to reload the stove, add more logs. Large logs burn slowly, holding a fire longer. Small logs burn fast
and hot, giving quick heat.
Adjust the Start-Up Air Control and Primary Control; the more you close down the Primary Control, the lower and slower
the fire will burn. The more you open the Primary Control, the more heat will be produced. The Start-Up Air Control
is only used for the first 5 to 15 minutes.
5.
6.
7.
8.
As long as there are hot coals, repeating steps 7 and 8 will maintain a continuous fire throughout the season.
NOTE: The special high temperature paint that your stove is finished with will cure as your stove heats. You will notice an
odor and perhaps see some vapor rise from the stove surface; this is normal. We recommend that you open a window
until the odor dissipates and paint is cured.
NOTE: Stove should be run full open for 15 minutes a day to keep air passages clean.
WARNING! ALWAYS OPERATE THIS APPLIANCE WITH THE DOOR
CLOSED AND LATCHED EXCEPT DURING START-UP AND REFUELING .
Page 16
WARNING! DO NOT LEAVE THE FIRE UNATTENDED WHEN THE DOOR
IS UNLATCHED. UNSTABLE FIREWOOD COULD FALL OUT OF THE
FIREBOX CREATING A FIRE HAZARD TO YOUR HOME.
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
OPERATING INSTRUCTIONS (Cont’d)
OPACITY
This is the measure of how cleanly your stove is burning. Opacity is measured in percent; 100% opacity is when an object
is totally obscured by the smoke column from a chimney, and 0% opacity means that no smoke column can be seen. As you
become familiar with your stove, you should periodically check the opacity. This will allow you to know how to burn your stove
as nearly smoke-free as possible (goal of 0% opacity).
BURN RATES
STARTING FIRE: Open (push in) both controls fully. After a wood load has been burning for 5 to 15 minutes (longer for very
large pieces) close the Start-Up Air Control by pulling it out (in the center of the pedestal).
HIGH: Leave the Primary Air Control fully open (immediately under the ashcatcher). It is important to do this when reloading the
stove. Failure to do this could result in excessive emissions (opacity).
After a wood load has been burning for 5 to 15 minutes on High to achieve the following burn rates
set the controls as listed below:
MEDIUM HIGH: Close the Primary Air Control to 1-1/4” to 2” (32-51mm) open, Start-Up Air is closed.
MEDIUM LOW: Close the Primary Control to 1” -1-1/4” (25-32mm) open. Start-Up Air is closed.
LOW: Gradually close down the Primary Control, making sure to maintain flames in the stove. (Start-Up Air is closed.) It is very
important to maintain flames in your stove during the first few hours of a low burn, to avoid excessive air pollution.
WOOD SELECTION AND STORAGE
CAUTION: DO NOT STORE WOOD CLOSER THAN THE REQUIRED CLEARANCES TO COMBUSTIBLE OF THE STOVE OR
WITHIN THE SPACE REQUIRED FOR LOADING AND ASH REMOVAL.
Burn only dry seasoned wood. Store wood under cover, out of the rain and snow. Dry and well-seasoned wood will not only
minimize the chance of creosote formation, but will give you the most efficient fire. Even dry wood contains at least 15% moisture
by weight, and should be burned hot enough to keep the chimney hot for as long as it takes to dry the wood out - about one hour.
It is a waste of energy to burn unseasoned wood of any kind.
Dead wood lying on the forest floor should be considered wet, and requires full seasoning time. Standing dead wood can
be considered to be about two-thirds seasoned. To tell if wood is dry enough to burn, check the ends of the logs. If there
are cracks radiating in all directions from the center, it is dry. If your wood sizzles in the fire, even though the surface is
dry, it may not be fully cured.
Splitting wood before it is stored reduces drying time. Wood should be stacked so that both ends of each piece are exposed to
air, since more drying occurs through the cut ends than the sides. This is true even with wood that has been split. Store wood
under cover, such as in a shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc., as uncovered wood can
absorb water from rain or snow, delaying the seasoning process.
BLOWER OPERATING INSTRUCTIONS
(see blower installation instructions on page 19)
If your Quadra-Fire wood stove is equipped with an optional blower, you should follow these guidelines:
1.
Initial (cold) start-up: Leave blower off until your stove is hot and a good coalbed is established. The blower may be
turned on approximately 15 minutes after loading the stove with fuel.
2.
High burn setting: The blower may be left on throughout the burn.
3.
Medium or Medium-High burn setting: The blower should be left off until a good burn is established, then turned on
at a medium or high rate.
4.
Low burn setting: The blower tends to cool off the stove. If you are using wet wood or a very low burn setting, leave
blower off until the burn is well established. Then, if you wish, turn the blower on at a lower rate. Too high a blower setting
with a low burn rate may adversely affect emissions.
5.
The blower is equipped with a speed control. The highest blower speed is obtained by turning the speed control to ON” and
then adjusting counterclockwise towards “OFF” as far as possible without turning the blower off. For a low blower speed,
turn the control knob clockwise as far as possible.
250-6931C November 3, 2004
Page 17
2100 ACT Millennium Wood Stove
R
MAINTENANCE and GLASS CARE
CREOSOTE
FIREBRICK
FORMATION AND NEED FOR REMOVAL: When wood is
The firebox of your Quadra-Fire stove is lined with high quality
firebrick, which has exceptional insulating properties. There is no
need to use a grate; simply build a fire on the firebox floor of your
stove. Do not operate stove without firebrick.
burned slowly, it produces tar and other organic vapors
which combine with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool
chimney flue of a newly-started or a slow-burning fire. As
a result, creosote residue accumulates on the flue lining.
When ignited, this creosote creates an extremely hot fire
which may damage the chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every two months during the heating season to
determine if a creosote or soot buildup has occurred. If
creosote or soot has accumulated, it should be removed
to reduce the risk of a chimney fire.
INSPECTION: Inspect the system at the stove connection
and at the chimney top. Cooler surfaces tend to build
creosote deposits quicker, so it is important to check the
chimney from the top as well as from the bottom.
REMOVAL: The creosote or soot should be removed with
a brush specifically designed for the type of chimney in
use. A chimney sweep can perform this service. It is also
recommended that before each heating season the entire
system be professionally inspected, cleaned and repaired
if necessary.
CHIMNEY CLEANING
Remove all ash from the firebox and extinguish all hot
embers before disposal. Allow the stove to cool completely.
Disconnect flue pipe or remove baffle from stove before
cleaning chimney. Otherwise residue can pile up on top of
the baffle and the stove will not work properly. Close the
door tightly and proceed with sweeping the chimney. Clean
out fallen ashes from the firebox.
DISPOSAL OF ASHES
Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed
on a noncombustible floor or on the ground, well away from
all combustible materials, pending final disposal. If the
ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container
until all cinders have thoroughly cooled.
OVERFIRING
Do not overfire. Using flammable liquids or too much
wood, burning trash in the stove, or allowing too much
air into the stove may result in overfiring. If the chimney
connector or stove glows red or even worse, white, the
stove is overfired. This condition may ignite creosote in
the chimney, which can be dangerous, possibly causing
a house fire. If you overfire, immediately close the air
controls and door, if open, to reduce the air supply to the
fire. Overfiring will void the stove warranty.
Page 18
GLASS CARE
NOTE: REMOVE ALL LABELS FROM GLASS BEFORE LIGHTING THE
FIRST FIRE IN YOUR STOVE.
Quadra-Fire stoves are equipped with ceramic super heat-resistant
glass, which can only be broken by impact or misuse. Do not slam
stove door or impact the glass. When closing door, make sure
that logs do not protrude against the glass. Clean glass with a
nonabrasive glass cleaner, such as Windex. Abrasive cleaners may
scratch and cause glass to crack. Inspect glass regularly. If you find
a crack or break, immediately put the fire out and return the door to
your dealer for replacement of glass before further use.
A portion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes” the
glass, helping to keep smoke from adhering to its surface. When
operated at a low burn rate, less air will be flowing over the glass
and the smokey, relatively cool condition of a low fire will cause the
glass to become coated. Operating the stove with the Primary Air
Control all the way open for 15-20 minutes should remove the built
up coating. If the deposits on the glass are not very heavy, normal
glass cleaners work well. Heavier deposits may be removed by using
a damp cloth dipped in wood ashes or by using a commercially
available oven cleaner. After using an oven cleaner, it is advisable
to remove any residue with a glass cleaner or soap and water. Oven
cleaner left on during the next firing can permanently stain the glass
and damage the finish on plated metal surfaces.
CARE AND CLEANING OF PLATED SURFACES
Clean plated surfaces with vinegar or a glass cleaner before lighting
your first fire.
CAUTION:
Do not use polishes with abrasives as it will
scratch the surface.
WARNING: When the appliance is equipped with a plated door,
you must clean all the fingerprints and oils from the surface before
firing the appliance for the first time. Use a glass cleaner or
vinegar and towel to remove the oils. If not cleaned properly
before lighting your first fire, the oils can cause permanent
markings on the plating. After the plating is cured, the oils will
not affect the finish and little maintenance is required: just wipe
clean as needed.
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
BRICK REPLACEMENT INSTRUCTIONS
Brick Set Part 831-1890
1. After the coals have completedly cooled, remove all old brick
2.
Remove new brick set from box and lay out to diagram shown.
3.
Lay bottom bricks in unit.
4.
Install rear bricks on the top of the bottom bricks. Slide top
of bricks under clip on back of firebox wall and push bottom
of brick back.
5.
Brick Size
9.0" x 4-1/2" x 1-1/4"
9.0" x 2-1/2" x 1-1/4”
7.0” x 4-1/2" x 1-1/4"
7.0" x 4-1/2" x 1-1/4"
5
6-3/4" x 4-1/2" x 1-1/4"
(with hole)
Qty in Set
12
3
1
1
1
1
2
4
2
1
1
1
1
1
Install side bricks. Slide top of brick under clips on side of
firebox and push the bottom of the brick until it is flush with
the side of the unit.
Nbr
1
2
3
4
3
1
and ash from unit and vacuum firebox.
1
1
1
1
1
2
5
Use Part 832-0550 when ordering individual brick. Provide
brick dimension or copy this page, mark the desired brick and
take it to your authorized dealer.
INSTALLATION OF OPTIONAL BLOWER, Part 831-1701
The blower is shipped fully assembled and ready for installation.
1. Remove the three bolts (1/4”-20 Phillips Head) on the outer skin at the bottom rear of stove.
2. Align holes in mounting flange of blower with bolt holes in stove. Blower should be positioned around bottom of rear outer skin
as shown in drawing below.
3. Reinsert and tighten bolts, securing blower onto outer wall of stove.
Do not remove ground from plug. Plug blower cord into a grounded outlet. Route power cord away from stove in such a
manner to avoid heat from the stove, traffic, or other damage. Do not route cord under or in front of stove.
ADJUSTING THE BLOWER SPEED CONTROL, IF NECESSARY*
*The blower speed control for this unit is
adjusted at the factory, and normally does
not require further adjustment.
NOTE: When the speed control is turned clockwise, it
will click on to high speed. Continue to turn the
speed control clockwise to decrease the speed. At
full clockwise, the blower should blow gently, but
should not stop.
1.
With the unit plugged in, turn the speed control knob
to slow (full clockwise).
2.
With a small screwdriver, adjust the blower speed by
turning the adjustment mechanism through the hole
on the side of the speed control.
3.
Adjust the speed so the blower runs slowly, but does
not stop. Turn clockwise to slow the blower and
counterclockwise to increase the speed.
250-6931C November 3, 2004
BLOWER SPEED CONTROL
Blower
Mounting
Flange
Outer
Skin
Page 19
R
2100 ACT Millennium Wood Stove
DOOR HANDLE ASSEMBLY
1.
2.
3.
4.
5.
6.
Install washer on door handle shaft.
Slide door handle through door.
Install second washer(s) as shown.
Install key in groove.
Align groove in latch cam with key; slide latch cam over shaft
Install locknut.
CAUTION! DO NOT OVERTIGHTEN LOCKNUT. DOOR
HANDLE NEEDS TO MOVE SMOOTHLY.
7. Install spring handle turning in a counter-clockwise motion to
desired location on handle.
Latch Cam
Door Cross Section
(example)
Locknut
Spring
Handle
Door Handle
Spacing
Washers
Square Key
GLASS REPLACEMENT
Replace with 5mm ceramic glass only, Part: 832-0050
1.
2.
3.
4.
5.
6.
7.
8.
9.
Ensure that the fire is out and the stove is cool to the touch.
Protect a table or counter top with padding or towels.
Remove the door with the broken glass by lifting the door up and off of the hinges.
Lay door face down on a table or counter making sure the handle hangs over the edge so the door lays flat, on a soft surface.
Remove the screws from each glass retainer and remove the glass. (if screws are difficult to remove, soak with penetrating oil first).
Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and right sides).
Replace the glass retainers. Be careful not to cross thread the screws.
Tighten each retainer just a few turns until each is secured. Check again for centering of glass in door frame. Then continue to
tighten each retainer alternately, a few turns at a time, until the glass is secure. DO NOT OVERTIGHTEN.
Replace the door on the appliance.
BAFFLE REMOVAL AND INSTALLATION
NOTE: The baffle in the 2100 Millennium is 2700° Fiber Board. Removing hardware exposed to combustion processes can be
frustrating. If your reason for removing the baffle is simply to clean the chimney, you have alternatives which will save time and effort.
Call a qualified chimney sweep or an authorized Quadra-Fire dealer for details.
1. Remove all ash from the firebox, and extinguish all hot embers before disposal into a metal container.
2. With a 3/16” allen wrench, remove the 2 front secondary combustion tube retainer bolts on the secondary air channel under
the end of the front tubes. See Figure 20A. NOTE: Soak the bolts with penetrating oil for at least 15 minutes before
trying to remove them.
3. To remove the secondary combustion tubes, slide the tube to one side until one end is out of its hole. Then, while lifting that end of
the fiber board, pull the tube up over the secondary air channel and out of the hole at the other end.
4. Slide fiber board forward to front of stove, tilt down and slide through the door. See Figure 20B.
5. To install the fiber board baffle, repeat steps 2 through 4 in reverse. Be sure that the fiber board baffle is pushed back fully.
FIGURE 20A - Allen wrench on retainer bolt
Page 20
FIGURE 20B - Baffle & Ceramic Blanket
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
EXPLODED VIEWS
4
1
Nbr
1
2
3
4
5
6
7
8
9
10
11
Part Name
Door, Cast
Door Handle
Glass, Replacement
Glass Frame Assembly
Glass Frame Screws (10)
Hinge Pins
Latch, Cam
Latch Cam key
Locking Nut
Spring Handle, 1/2”
Trim for Door
(Trim Door Assembly only)
12 Washer, Spacing
5
9
8
6
7
10
2
12
3
11
DOOR, GLASS AND DOOR HANDLE ASSEMBLY
1
5
4
Nbr
7
6
2
3
250-6931C November 3, 2004
1
2
3
4
5
6
7
Part Name
Baffle, Fiberboard
Door Frame
Glass Assembly
Hinge Pins (2)
Manifold Tubes (3)
Oak Trim, Pedestal (2)
Spring Handles (2)
for Air Controls
Page 21
2100 ACT Millennium Wood Stove
R
ACCESSORIES
831-1701 . . . . . Blower Assembly
832-1082 . . . . . Door Assembly, Black (installed on the stove)
832-1902 . . . . . Door Assembly, Gold Trim
DR-21NL. . . . . . Door Assembly, Nickel Trim
UK-DRNL . . . . . Nickel Upgrade Kit (includes (2) hinge pins, (3) spring handles)
831-1780 . . . . . Outside Air Kit
SERVICE PARTS
831-2040
831-1890
832-0550
473-5040
832-1680
832-0050
831-1900
832-0620
832-0630
. . . . . Baffle, Fiberboard
. . . . . Brick Set
. . . . . Brick, Pumice, Single (give dimensions needed, see page 21)
. . . . . Door Handle Assembly
. . . . . Door Rope, 3/4”, cut to size in the field
. . . . . Glass Assembly for Door, with gasketing
. . . . . Manifold tubes, set of 3
. . . . . Spring Handle, Door, ½”, Gold
. . . . . Spring Handle, Air Control, ¼”, Gold, (pair)
APPLIANCE
2100 Millennium
Advanced Combustible Technology (ACT)
Page 22
21M-GT
2100 Millennium, Gold Trim Door, Pedestal
21M-NT
2100 Millennium, Nickel Trim Door, Pedestal
250-6931C November 3, 2004
2100 ACT Millennium Wood Stove
R
Lifetime Warranty
LIMITED LIFETIME WARRANTY
The Hearth & Home Technologies limited Lifetime Warranty guarantees that the following components will work as designed
for the lifetime of the stove or Hearth & Home Technologies will repair or replace them. These items include but are not limited
to steel and cast iron components, all gas burners, gas logs, combustion chambers, heat exchanger systems, stainless steel
firebox components, plating, doors, glass damaged by thermal breakage, steel baffle supports, steel and ceramic baffles and
manifold tubes. Labor is for the first five years.
THREE YEAR WARRANTY
Our EZ Clean firepots are covered under Hearth & Home Technologies three-year warranty program. Labor is for 3 years.
TWO YEAR WARRANTY
All electrical components such as but not limited to blowers, wiring, vacuum switches, speed controls, control boxes,
thermodisc switches, pilot assembly, gas valves, thermostats and remotes are covered under Hearth & Home Technologies
two-year warranty program. Labor is for two years.
ONE YEAR WARRANTY
Porcelain finishes are warranted against manufacturer defects for one year. Labor to repair or replace these parts is covered
for one year, reimbursed per our warranty service fee schedule.
CONDITIONS
This warranty is non-transferable and is made to the original retail purchaser only provided that the purchase was made
through an authorized dealer of Hearth & Home Technologies. It must be installed and operated at all times in accordance with
the Installation and Operating Instructions furnished with this product, as well as any applicable local and national codes. Any
alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
Labor to repair or replace items covered under the limited Lifetime Warranty will be covered for the first five years per our
warranty service fee reimbursement schedule. Parts covered under the limited Lifetime Warranty will be covered for the
lifetime of the appliance up to a maximum of ten (10) years after Hearth & Home Technologies discontinues the model and two
(2) years for optional accessories. Adjustments, regular maintenance, cleaning and temporary repairs do not qualify for a
service call fee and will not be covered. The replacement of consumer replaceable items and installation of upgraded
component parts do not quality for a service call fee, and will not be covered.
This limited Lifetime Warranty does not extend to or include surface finish on the appliance, door gasketing, glass gasketing,
glass, firebrick, pellet logs, igniters, kaowool or other ceramic insulating materials. It does not cover installation or
operational-related problems such as overfiring, use of corrosive driftwood, downdrafts or spillage caused by environmental
conditions, nearby trees, buildings, hilltops, mountains, inadequate venting or ventilation, excessive offsets, or negative air
pressures caused by mechanical systems such as furnaces, fans, clothes dryers, etc.
Any installation, construction, transportation, or other related costs or expenses arising from defective part(s), repair,
replacement, etc., will not be covered by this warranty, nor will Hearth & Home Technologies assume responsibility for them.
Further, Hearth & Home Technologies will not be responsible for any incidental, indirect, or consequential damages, except as
results in damage to the interior or exterior of the building in which this appliance is installed. This limited Lifetime Warranty
does not apply to the venting components, hearth components or other accessories used in conjunction with the installation of
this product not manufactured by Hearth & Home Technologies
This warranty is void if the stove has been overfired or operated in atmospheres contaminated by chlorine, fluorine, or other
damaging chemicals, the stove is subjected to prolonged periods of dampness or condensation, or there is any damage to the
stove or other components due to water or weather damage which is the result of, but not limited to, improper chimney or
venting installation. Hearth & Home Technologies may, at its discretion, fully discharge all obligations with respect to this
warranty by either repairing or replacing the unit, or refunding the wholesale price of the defective part(s).
This limited Lifetime Warranty is effective on all appliances sold after May 1, 2002 and supersedes any and all warranties
currently in existence.
Policy 250-8620 Rev F
250-6931C November 3, 2004
Page 23
R
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer,
call 1-800-926-4356
CAUTION
• Do NOT discard this manual.
• Important operating and maintenance
instructions included.
• Read, understand and follow these instrucitons for safe installation and operation.
• Leave this manual with party responsible for
use and operation.
ATTENTION INSTALLERS:
PLEASE RETURN THESE INSTRUCTIONS TO THE HOME
OWNER WHEN THE INSTALLATION IS COMPLETE.
This product may be covered by one or more of the following patents: (United States) 4593510,
4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062,
5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502,
6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436;
(Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending.
Page 24
250-6931C November 3, 2004
Download PDF

advertising