Vidifox PV 700ST User Manual

Vidifox®
Document Camera
PV 700ST
USER MANUAL
Please read this User Manual thoroughly before you use the document camera. Keep the CD-ROM in
a convenient place so you can use it quickly if you need to.
Please visit us at http://www.waninusa.com where you can get product support, the latest driver
updates, and answers to frequently asked questions (FAQs) and technical questions.
1
PRECAUTIONS
NOTICES: PLEASE READ CAREFULLY BEFORE USE










Use the document camera under the rated electric conditions.
Do not place the document camera on any unstable surface. It may fall and cause injuries or
damages.
Do not place this device directly under sunlight or near heaters.
Do not place this device near water.
Keep the camera away from acid or alkali gas.
Do not place this document camera in humid, dusty, windy or vibrant locations.
The recommended operating environment is:
Temperature:
32ºF-113ºF (0ºC--45ºC)
Humidity:
less than 75%
Always unplug BEFORE cleaning the device. Use a damp soft-cloth for cleaning. Do not
use volatile solvent.
When this equipment functions abnormally, such as smoke, smell, noise, immediately
unplug and call for professional assistance.
Unplug the document camera or shut off the power when not in use.
Legal Notice
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Compilation and Publication Notice
This manual has been compiled and published to cover the latest product’s descriptions and
specifications. The contents of this manual and the specifications of this product are subject to
change without notice.
Wanin USA reserves the right to make changes without notice in the specifications and materials
contained herein and shall not be responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to typographical and other errors relating
to the publication.
© 2012 Wanin USA Inc. All Rights Reserved.
2
Table of Contents
1. PARTS IDENTIFICATION.................................................................5
2. CONTROL PANEL ..............................................................................6
3. Annotation Functions on Touch Screen....………………….……….8
4. INPUTS AND OUTPUTS ....................................................................9
5. REMOTE CONTROL ........................................................................10
6. CONNECTIONS..................................................................................13
6.1. COMPUTER CONNECTION .........................................................................................13
6.2. USB-A CONNECTION ...................................................................................................14
6.3. VGA OUTPUT CONNECTION......................................................................................15
6.4. C-VIDEO OUTPUT CONNECTION..............................................................................15
6.5. S-VIDEO OUTPUT CONNECTION ..............................................................................16
6.6. DVI OUTPUT CONNECTION .......................................................................................16
7. COMMUNICATE WITH COMPUTER ..........................................17
7.1. COMPUTER REQUIREMENTS ....................................................................................17
7.2. CONTROL VIA RS232 ...................................................................................................17
7.3. USB FUNCTION.............................................................................................................22
7.3.1. USB-A...................................................................................................................22
7.3.2. USB-B ...................................................................................................................22
7.3.2.1. COMPUTER REQUIREMENTS ..............................................................20
7.3.2.2. PREPARATION FOR INSTALLATION ...................................................20
7.3.2.3. SOFTWARE INSTALLATION .................................................................24
7.3.2.4. START THE SOFTWARE .....................................................................28
7.3.2.5. IMAGE CONTROL...................................................................................29
7.3.2.6. IMAGE CAPTURE AND VIDEO RECORDING.....................................31
7.3.2.7. SETTING ...................................................................................................32
7.3.2.8. IMAGE MODIFY ....................................................................................33
8. FEATURES .........................................................................................41
LIGHT.....................................................................................................................................41
ZOOM IN AND ZOOM OUT ................................................................................................41
POSITIVE/NEGATIVE CONVERSION ...............................................................................41
FOCUS ADJUSTMENT .........................................................................................................41
BRIGHTNESS ADJUSTMENT .............................................................................................42
WHITE BALANCE ADJUSTMENT .....................................................................................42
IMAGE FREEZE ....................................................................................................................42
IMAGE ROTATE....................................................................................................................42
3
SPLIT SCREEN......................................................................................................................42
TITLE FUNCTION ................................................................................................................42
PICTURE IN PICTURE FUNCTION ....................................................................................42
IMAGE SAVE.........................................................................................................................42
IMAGE RECALL ...................................................................................................................42
RGB INPUT SWITCH ...........................................................................................................43
OUTPUT SWITCH.................................................................................................................43
USB IMAGE CAPTURE AND VIDEO RECORDING.........................................................43
RS232 CONTROL ..................................................................................................................43
9. SPECIFICATION ...............................................................................43
10. TROUBLE-SHOOTING..................................................................44
11. PACKING LIST................................................................................45
12. TECHNICAL SUPPORT .................................................................46
4
1. PARTS IDENTIFICATION
1.
Remote control IR receiver
2.
Camera
3.
LED light box
4.
Upper mechanical arm
5.
Main mechanical arm
6.
Side panel
7.
Back panel
8.
Control panel
9.
LCD
5
2. CONTROL PANEL
1. POWER: Turn on/off the power.
2. MENU ENTER:
a. Activate the on screen menu.
b. Display the selected image in Image Recall mode.
3. PC | CAM : Press this button to toggle between the image from the Camera and the VGA input.
4. AUTO : a. Carry out automatic adjustment for focus, color and white balance.
b. When in Image Recall mode, press this button to delete a selected image.
5. ZOOM+/-: Image zoom in and zoom out control.
6
3. Annotation Functions on Touch Screen
1、
: Enter to the setting menu
2、
：Active the function menu
1、
：Image split
2、
：Title function
3、
：Brightness+
4、
：Brightness-
5、
：Image freeze
6、
：Image rotate
7、
：Focus+
8、
：Focus-
9、
：Image capture
10、
：Text/Picture function
11、
：Lamp on/off
12、
：Image mirror
13、
：Picture-in-picture function
14、
：Negative/positive conversion
15、
：Image recall
16、
：Exit
3、
：Annotation function
1、
：Select writing pen
2、
：Select clear pen
3、
：Rubber
4、
：Delete all annotation
5、
：Cursor
6、
：Select the pen's color: Red
7
7、
：Select the pen's color:Yellow
8、
：Select the pen's color:Blue
9、
：Select the thickness of writing
10、
：Select the thickness of writing
11、
：Select the thickness of writing
8
4. INPUTS AND OUTPUTS
1. DC 12V: Power input.
2. RS 232: Serial port, to control the document camera from a computer via this port.
3. DVI: DVI-A signal output.
4. AUDIO OUT: Audio output.
5. VGA OUT: VGA (RGB) signal output (15 pin D-SUB).
6. PC OUT: VGA (RGB) signal output (15 pin D-SUB).
7. VGA IN: VGA (RGB) signal input (15 pin D-SUB).
8. AUDIO IN: Audio input.
9. USB-A: Communicate with a USB device, such as a USB mouse or USB drive stick.
10. USB-B:
a. In USB Video Mode, capture images or record video into a connected
computer via provided software;
b. In USB Disc Mode, download saved images to a connected computer.
9
5. REMOTE CONTROL
1.
: Turn the document camera on or off.
2. PC/CAM: Press this button to toggle the output image between the document camera and
VGA-IN.
10
3. MIR: Output right-and-left, up-and-down mirror image
4. Output Format: Press this button to activate the Output Format selection menu on screen. Use
Up and Down arrows to select a desired output format, press MENU ENTER button to
confirm.
5. Arrow Buttons:
a. In Image Recall Mode, use arrow buttons to navigate the thumbnail images;
b. In On-Screen Menu mode, use arrow buttons to select menu items (see details below).
6. MENU ENTER
a. In Camera mode, press and hold the MENU ENTER button to enter the On-Screen Menu
mode, then
1. Use left and right arrow buttons to navigate the menu bar;
2. Press MENU ENTER button briefly to enter the submenu;
3. Use up and down arrows to select a function;
4. Use left and right arrows to change parameters of the selected function.
5. Press and hold MENU ENTER button at anytime to exit the On-Screen Menu mode.
b. In Image Recall mode, press MENU ENTER button to display a selected image.
7.
: Turn the LED light on or off.
8.
: Activate the USB Mode selection menu on screen. Use Up and Down arrows to select
USB Disc, USB Video, or Exit, press MENU ENTER button to confirm.
9. Save: Capture the current image. If a USB drive is connected to the document
camera, the image will be saved to the USB drive; otherwise, the image will be saved to internal
memory.
10. RECALL:
a. In Camera Mode, press this button to enter the Image Recall mode.
(1) When no USB drive is connected to the document camera, thumbnails of images in the
internal memory will be displayed. Use PAGE+/- keys to navigate between pages; Use
arrow keys to select a thumbnail; Press MENU ENTER button to display the selected
image.
(2) When a USB drive is connected to the document camera, contents of the USB drive
will be displayed on screen. Use up and down arrows to select a folder or image file;
Press MENU ENTER button to enter the selected folder or display the selected image.
b. In Image Recall mode, press this button to go back to an upper level.
11. Page +/-: in Image Recall mode, navigate between pages of thumbnail images.
12. AUTO DEL:
a. In Camera mode, carry out automatic adjustment for focus, color and white balance.
b. In Image Recall mode, press this button to delete a selected image.
13. TITLE: Enable the title function.
14. Zoom+/-: Image zoom in and zoom out control.
11
15. Split: Split screen, enable the comparison between the frozen image and live image.
16. Bri+/-: Image brightness adjustment.
17. Frz: Freeze/unfreeze the image
18. Fc+/-: Adjust focus manually, focus far and focus near.
19.
: Rotate the image by 90o, 180o, 270o.
20. Sharp+/-: Adjust sharpness of the image.
21. Neg: Switch the image between positive and negative colors.
22. PIP: Active the Picture in Picture function. Press PIP, it will appear the saved picture, then
select on picture for PIP picture.
23. T/P: Switch the output image between the text mode and picture mode.
12
6. CONNECTIONS
6.1. COMPUTER CONNECTION
13
6.2. USB-A CONNECTION
14
6.3. VGA OUTPUT CONNECTION
15
6.4. DVI OUTPUT CONNECTION
16
7. COMMUNICATE WITH COMPUTER
7.1. COMPUTER REQUIREMENTS
The PC's hardware and software configurations shall not be less than the following requirements：
Operating system: Windows XP
CPU: 1.8 GHz
Physical memory: 512M
Video memory: 64M
7.2. CONTROL VIA RS232
PV 700ST can be controlled from a computer via RS232.
1. Double click the RS232 software in provided CD to run the install shield wizard.
Then you will see the software setup window:
Read terms, select "I accept the terms in the license agreement" Click Next:
17
Click Change to change the installation directory if needed, then click Next:
Click Install to install the software to the computer:
18
Click Finish, the software installation is complete:
2. Connect the computer to the PV 700ST with a RS232 cable, turn on the power of PV 700ST.
3. Double click on
or click start->All Programs->Visualizer_RS232->
Visualizer_RS232.exe to run the RS232 software, you will see the icon
the control interface on the top right of the screen:
: Zoom+
19
on the task bar and
: Zoom: Auto
: Display all functions
: Minimize
: Close
4. Click on
, you will see the following control panel.
5. Properly set the software.
Select the corresponding model number
Select the right COM port
20
Note:
* If the selected model does not have certain functions, the corresponding buttons in the software
interface are displayed in light gray and are not clickable.
* All models require 15 seconds start-up time to start the software.
6. Button instruction
Button
Function
Power On
Power on the unit
Power Off
Stand by
PC In/Home
Switch between PC and Visualizer inputs
VGA /Video Out Switch between VGA and Video outputs
F reeze
Image Freeze
L ight
Toggle between arm light and no light
Brightness+
Increase the brightness
Brightness-
Decrease the brightness
Focus+
Focus far
Focus-
Focus near
Zoom+
Zoom in
Zoom-
Zoom out
Page+
Page up
Page-
Page down
Red+
Increase the red hue
Red-
Decrease the red hue
21
Blue+
Increase the blue hue
Blue-
Decrease the blue hue
S harpness+
Increase the sharpness
S harpness-
Decrease the sharpness
A uto
Auto focus, brightness and color
S ave
Save image
Recall
Recall saved images
NEG
Switch between negative and positive image
modes
B/W
Switch between color and black/white modes
S plit
Split screen
M irror
Mirror image
T/P
Switch between text and image modes
Rotate
Rotation
P IP
Picture in picture
XGA
Switch
between
output modes
E nter
Enter
U p
Up
D own
Down
L eft
Left
Right
Right
22
SXGA,
XGA,
and
WXGA
USB
USB function selection
T itle
Title freeze
M enu
Menu
7.3. USB FUNCTION
7.3.1. USB-A
USB-A connector can be used to communicate with a USB mouse, a USB drive, or other USB slave
device.
1. USB Mouse
The USB mouse will be automatically activated when pluged into the USB-A connector of PV
700ST, you can use it to annotate on the image.
2. USB Drive
 Connect a USB drive to PV 700ST, then press Recall button to access the USB drive.
 Use the left and right arrows to exit or enter a folder.
 Use the up and down arrows to select an image.
 Press Menu Enter to display the selected image.
 Press Recall button to exit.
7.3.2. USB-B
7.3.2.1. COMPUTER REQUIREMENTS
Visualizer_USB Camera software is an application that allows users to capture images, preview and
record video under the Windows operating systems.
Visualizer_USB Camera software runs on MS Windows XP, Windows 7, and Vista operating
systems. The minimal requirements for the computer hardware are:
Operating system: Windows XP
CPU: 1.8 GHz
Physical memory: 512M
Video memory: 64M
23
7.3.2.2. PREPARATION FOR INSTALLATION
To install and uninstall, please login in as system administrator, otherwise, the install/uninstall
will fail.
Please connect the unit to the PC before starting installation.
Please select the right software to install: Visualizer_USB(x32):
Windows XP, 32bit. Visualizer_USB(Windows7 x64): Windows
7, 64bit.
Visualizer_USB(Vista x64): Windows Vista, 64bit.
For Vista system, please do not choose “Use User Account Control (UAC) to help protect your
computer”, follow the step to complete the setting:
1. Open the control panel, then click User accounts:
2. Click on “Turn User Account Control on or off”, you will see:
24
3. Do not tick the option “Use User Account Control (UAC) to help protect your computer”:
For Windows 7, please change the User account control setting to Never Notify. Follow the step
to complete the setting:
1. Click on the right key of the mouse, choose properties:
25
2. Click on Action center:
3. Click on Change User Account Control Setting, then choose Never notify.
26
7.3.2.3. SOFTWARE INSTALLATION
Double click to run the software installation package, the following dialogue appears, click "Next":
Read the terms, select "I accept the terms in the license agreement." Click "Next", as the following
figure.
27
The following dialogue box appears, click "Next":
The default installation directory is Program Files, C: \ Program Files \, you can select a different
installation directory, as shown:
28
Click on "Change" to change the directory, as shown:
Click on "OK", the following figure appears. Click "Next".
29
Click on "Install" to complete installation, as shown:
Click on "Finish” to complete the installation, as shown:
30
Then you will see the following interface, which is an installation package for 2005 environment. If
your PC already has this installed, click on "No" to exit, otherwise, click on "Yes" to install it.
7.3.2.4. START THE SOFTWARE
Note: To use the software, the document camera’s USB mode has to be set to USB Video mode.
Please follow the instruction below:
A. Make sure the USB cable is disconnected from the unit.
B. Press the USB button on the remote, a dialog box appears on the screen, under which you
will see USB disk or USB video, use the arrow keys on the remote or control panel to
select the USB video mode.
The remote and the front panel are inactive while the software is in use.
Double click on the short cut
on the desktop, then click on Device, select the right
model number, see below:
31
Then click on
, or select Video->Play, you will see the interface:
7.3.2.5 IMAGE CONTROL

Zoom in and Zoom out
Zoom In （Ctrl+I）: Left-click the Zoom In command button to enlarge the image.
Zoom Out（Ctrl+O）: Left-click the Zoom Out command button to shrink the image.
32

Focus adjustment
F ocus Far（Ctrl+R）: Left click the Focus Far command button to focus far.
Focus Near（Ctrl+N）: Left click the Focus Near command button focus near.

Image Brightness adjustment
Bright More （Ctrl+B）: Left click the Bright More button to increase the brightness.
Bright Less （Ctrl+L）: Left click the Bright Less button to reduce the brightness.

Sharpness adjustment
Sharp More: Left click the Sharp More button to increase the sharpness.
Sharp Less: Left click the Sharp Less button to reduce the sharpness.

Auto focus
Auto （Ctrl+U）: Left click the Auto button to auto adjust the focus.

Mirror adjustment
Mirror（Ctrl+M）: Left
click
the
Mirror
button
to
adjust
image
mirror, horizontal mirror, vertical mirror, and horizontal /vertical mirror.

Image red hue adjustment
Red More: Left click the Red More button to increase the red hue.
Red Less: Left click the Red Less button to reduce the red hue.

Image blue hue adjustment
Blue More: Left click the Blue More button to increase the blue hue. Blue
Less: Left click the Blue Less button to reduce the blue hue.
33
to
normal

Image black and white/ color adjustment
Mono/Color（Ctrl+K） :
between the
Left
click
the
Mono/color
button
to
toggle
black-white and color modes.

Positive and negative film images
Neg（Ctrl+G） : Left click the Neg button to toggle between the positive and negative
modes.
7.3.2.6. IMAGE CAPTURE AND VIDEO RECORDING
Left click on
to capture images. The captured images will be automatically saved into the
default destination folder. The path and file name are displayed in software status bar on the bottom
of the window. Shown below:
and does
not work. The detailed information is displayed on the software status bar in the bottom of the
window. The video is automatically saved in the default folder or pre-set folder.
Left click on
to start recording. The setting button will changes to
34
7.3.2.7. SETTING
The captured images and recorded videos will be saved into the folders of Images and Videos
respectively, which are created by the system automatically. To set a different path to which the
image/video is be to saved, click on
appears below.
on the left side of the window, a pop up dialog box
Save the captured images into a different folder
Click on the button next to the "select a folder to save picture files" text box to set the path for
captured images.
Save the recorded video into a different folder and set up parameters for videos
Click on the button next to the "Select a folder to save video files:" text box to set the path for videos.
You can also change the video settings. The Audio input (optional) drop down box offers the options
of recording video with or without sound. Shown below:
The length of video that can be recorded box displays the longest recording time for videos to be
saved in the preset path. Shown below:
Click on Save to complete.
35
7.3.2.8. IMAGE MODIFY
Click on

, you will see the interface:
Grapic selection and move
Click on
to choose a line, circle, rectangle or curve that placed in the image,
then move to another place.

Line
Click on
to place a beeline in the image, shown as below:
36
Click on
to change the setting of the chosen line:
Line width: change the width of the line.
X, Y: change the position of the line.
Color: change the color of the line.
Width, Height: Change the angle of the line.

Rectangle
Click on
to place a rectangle in the image, shown as below:
Click on
to change the setting of the chosen rectangle:
37
Line width: change the line width of the rectangle.
X, Y: change the position of the rectangle.
Color: change the line color of the rectangle.
Fill Color: Tick it to fill color in the rectangle.
Width, Height: Change the shape of the rectangle by changing the angle of two adjacent lines
of the rectangle.

Circle
Click on
to place a circle in the image, shown as below:
38
Click on
to change the setting of the chosen circle:
Line width: change the line width of the circle.
X, Y: change the position of the circle.
Color: change the line color of the circle.
Fill Color: Tick it to fill color in the circle.
Width, Height: change the size of the circle.

Curve
Click on
to place a curve in the image, shown as below:
39
Click on
to change the setting of the chosen curve:
Line width: change the line width of the curve.
X, Y: change the position of the curve.
Color: change the line color of the curve.

Graphic default setting
Click on

to change the setting of the graphic:
Graphic delete
Click on
to delete the chosen graphic.
40
Delete all graphics
Click on
to delete all graphics placed in the image.
8. FEATURES
LIGHT
Press “LAMP” to turn on or turn off the light.
ZOOM IN AND ZOOM OUT
Press "ZOOM+"or "ZOOM-"
POSITIVE/NEGATIVE CONVERSION
Press the Neg button on the remote control, the output image will be converted to negative color.
Press it again, the output image will be converted back to original color.
FOCUS ADJUSTMENT
When the PV 700ST is turned on the focus automatically adjusts to the stage, it
is usually not necessary to re-adjust the focus if you are only working with flat
materials (text, photos, etc.).
41
Only 3D objects require a focus adjustment. Press the “AUTO” button to auto focus. Press the
"FOCUS+" or "FOCUS-" button to focus manually.
BRIGHTNESS ADJUSTMENT
If the image effect is not satisfactory, you can adjust the brightness to get a better image effect.
Use the “BRIGHT+” or “BRIGHT-” button to adjust the brightness.
WHITE BALANCE ADJUSTMENT
Each time the lighting condition changes, the user should adjust the white balance of the image.
Press the “AUTO” button to adjust the white balance automatically.
IMAGE FREEZE
The freeze function allows you to discretely prepare the next image without interrupting current
presentation. Press "Freeze" on remote control to freeze and unfreeze the image.
IMAGE ROTATE
Press “Rotate” on the control panel to rotate the image by 90o, 180o, 270o.
SPLIT SCREEN
Press “SPLIT” to compare two images or compare two different views of one object side by side.
TITLE FUNCTION
Press “TITLE” to enable the title function.
PICTURE IN PICTURE FUNCTION
Press “PIP” on remote control to active the picture in picture function.
IMAGE SAVE
The PV 700ST offers the opportunity of storing 400 images on board. You can recall them by just
pressing
one
of
the
numerical
buttons
on
the
front
panel
or
remote
control.
Press"SAVE" to capture the image displayed.
IMAGE RECALL
By pressing “RECALL”, all saved images are displayed in the thumbnail index mode for easy
42
selection.
RGB INPUT SWITCH
Press the “PC | CAM” to select the VGA input signal instead of the signal from camera.
OUTPUT SWITCH
Use “OUTPUT” to select DVI signals output instead of VGA signal.
USB IMAGE CAPTURE AND VIDEO RECORDING
The USB port can be used to capture still images from the PV 700ST into a computer. In this way,
the PV 700ST can be used as a 3-D scanner for your computer.
RS232 CONTROL
The RS232 terminal allows you to integrate the PV 700ST into any sophisticated central
control system. RS232 also enable you to control the PV 700ST via computer.
9. SPECIFICATION
Model
PV 700ST
Sensor
1/3" CMOS
Pixels
Zoom
2Megapixel
fMeMegapixe
9x optical,
12x digital
l
15
Frame rate
Shooting area
Focus
Max: 13.5" x 10.6" /34.3 cm x 26.9 cm
Min: 0.1" x 0.1"/0.3 cm x 0.3 cm
Auto/manual
Output resolution
XGA, SXGA,720P
Resolution(Horizontal)
≥750 TV lines
White balance
Auto/manual
Color adjustment
Yes
Brightness adjustment
Yes
Negative&Positive conversion
Yes
Image capture
Yes, 400 NON-volatile images
Video recording
Yes(via USB)
43
Image rotation
Yes
Image split
Yes
Image freeze
Yes
Picture in picture
Yes
Title
Yes
OSD
Yes
Menu
Yes
Inputs
VGA ×1, AUDIO ×1
Outputs
DVI×1,VGA ×2, AUDIO ×1
USB2.0
Slave×1(USB camera), Host×1
RS232
x1(computer controllable)
Remote control
Yes(360°controllable)
Light source
LED light box
Kensington lock
Yes
Operating temperature
32°F ~113°F
Dimensions
Folded:12.6"×7.5"×5.6", Setup:15.7"×7.5"×19.7"
Power supply
12V DC power adapter
Weight(net)
6.2lbs/2.8kg
10. TROUBLE-SHOOTING:
Symptoms
Possible causes/counter-measures
No image
1. Power cord is not properly connected.
2. Cables are not properly connected.
3. Power switch is not turned on.
4. Change the output resolution.
Image bending
1.
Camera not in right position, adjust the camera.
2.
Distortion of LCD display, press the “Auto adjust” of the
LCD.
Out of focus or blurring
1. The object is too close to the lens.
image
2. Focus is on the top point of zoom, press ZOOM-.
3. Auto-focus is not on: press AUTO again.
4. Fog on the lens in damp climate. It will disappear
gradually when the equipment warms up.
44
If the problem still remains after checking the above, consult your dealer or authorized service
personnel.
11. PACKING LIST
Item
Quantity
Power cord
1
Power adaptor(12V/2A)
1
VGA cable
1
Mini jack audio cable
1
Switch cable
1
USB cable(2.0)
1
Remote control
1
User manual(CD)
1
Stylus
1
45
12. TECHNICAL SUPPORT
Wanin USA is committed to providing highest possible stand of customer service.
We can be
reached:
By Phone
Call us at 1-877-369-3130. Our technical support staff provides technical assistance from 9:00AM
through 5:00PM Pacific Standard Time, Monday through Friday. Please gather the following
information before calling:
- Product model name(s) and numbers
- Product serial number(s)
- Detailed questions or problem descriptions.
Online
Technical support is also available online at Wanin USA’s web site at www.waninusa.com.
You can enter your questions and concerns through our online form, email us at
[email protected].
Wanin USA Inc.
12961 Ramona Blvd., Irwindale, CA 91706
Toll Free: 1-877-369-3130
E-mail: [email protected]
©2012 Wanin USA Inc. All Rights Reserved.
46
Fax: 626-609-3380
Web: www.waninusa.com
">