GF8100 M2+ TE Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ............................................................ 1
1.1
Before You Start ................................................................................ 1
1.2
Package Checklist ............................................................................. 1
1.3
Motherboard Features...................................................................... 2
1.4
Rear Panel Connectors ..................................................................... 3
1.5
Motherboard Layout......................................................................... 4
Chapter 2: Hardware Installation ............................................. 5
2.1
Installing Central Processing Unit (CPU)....................................... 5
2.2
FAN Headers...................................................................................... 7
2.3
Installing System Memory ................................................................ 8
2.4
Connectors and Slots ....................................................................... 10
Chapter 3: Headers & Jumpers Setup ..................................... 12
3.1
How to Setup Jumpers .................................................................... 12
3.2
Detail Settings.................................................................................. 12
Chapter 4: RAID Functions ..................................................... 19
4.1
Operation System............................................................................ 19
4.2
Raid Arrays ...................................................................................... 19
4.3
How RAID Works............................................................................. 19
Chapter 5: Useful Help ............................................................ 23
5.1
Driver Installation Note.................................................................. 23
5.2
Software............................................................................................ 24
5.3
Extra Information............................................................................ 29
5.4
AMI BIOS Beep Code....................................................................... 31
5.5
Troubleshooting............................................................................... 32
Appendix: SPEC In Other Language........................................ 34
German.................................................................................................................. 34
France .................................................................................................................... 36
Italian..................................................................................................................... 38
Spanish ................................................................................................................... 40
Portuguese ............................................................................................................ 42
Polish...................................................................................................................... 44
Russian ................................................................................................................... 46
Arabic..................................................................................................................... 48
Japanese ................................................................................................................ 50
GF8100 M2+ TE
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
IDE Cable X 1
Serial ATA Cable X 1
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)
Note: The package contents may differ by area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Socket AM2+
CPU
AMD Athlon 64 / Athlon 64 FX / Athlon 64 x2
/ Sempron / PhenomX3 processors
Chipset
Support HyperTransport 3.0
Supports up to 5.2 GT/s Bandwidth
GeForce 8100
Low Pin Count Interface
ITE 8718
Super I/O
Provides the most commonly used legacy
Super I/O functionality
Environment Control initiatives
H/W Monitor
ITE's "Smart Guardian" function
DDR2 DIMM Slots x 2
Dual Channel Mode DDR2 memory module
Main
Max Memory Capacity 8GB
Supports DDR2 533 / 667 / 800
Memory
Each DIMM supports 256MB/512MB/
Supports DDR2 1066 (by AM2+ CPU)
1GB/2GB/4GB DDR2
Registered DIMM and ECC DIMM is not supported
Graphics
Integrated in GeForce 8100 Chipset
IDE
Integrated IDE Controller
SATA II
Integrated Serial ATA Controller
LAN
Realtek RTL 8201CL PHY
Sound
ALC662
Max Shared Video Memory is 512MB
DX10 / HDCP / PureVideo support
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4,
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
10 / 100 Mb/s auto negotiation
Half / Full duplex capability
5.1 channels audio out
High Definition Audio
PCI Express Gen2 x16 slot
x1
Supports PCI-E Gen2 x16 expansion cards
PCI slot
x2
Supports PCI expansion cards
On Board
Floppy connector
x1
Each connector supports 2 Floppy drives
Connector
IDE Connector
x1
Each connector supports 2 IDE device
SATA Connector
x4
Each connector supports 1 SATA devices
Front Panel Connector
x1
Supports front panel facilities
Slots
2
computing
Supports Hyper Transport 3.0 and PowerNow
(Maximum Watt: 95W)
FSB
AMD 64 Architecture enables 32 and 64 bit
GF8100 M2+ TE
SPEC
Back Panel
I/O
Front Audio Connector
x1
Supports front panel audio function
CD-in Connector
x1
Supports CD audio-in function
CPU Fan header
x1
CPU Fan power supply (with Smart Fan function)
System Fan header
x1
System Fan Power supply
CMOS clear header
x1
Restore CMOS data to factory default
USB connector
x3
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
Printer Port Connector
x1
Each connector supports 1 Printer port
Serial port Connector
x1
Connects to RS-232 Port
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
DVI port
x1
Connect to DVI-D monitor
VGA port
x1
Connect to D-SUB monitor
LAN port
x1
Connect to RJ-45 ethernet cable
USB Port
x4
Connect to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
Board Size
175 mm(W) x 245 mm(L)
MicroATX
Special
RAID 0 / 1 / 5 / 0+1 support
Features
Hybrid SLI support (by nVIDIA driver)
Biostar Reserves the right to add or remove support
OS Support Windows XP / VISTA
1.4
for any OS With or without notice.
REAR PANEL CONNECTORS
PS/2
Mouse
LAN
Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
PS/2
Keyboard
VGA
DVI-D
USBX2
USBX2
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
JKBMS
JATXPWR2
JKB_PWR
VGA
DIMMB1
DVI
AM2+
DIMMA1
Socket
JATXPWR1
JUSB1
IDE
JUSBPWR1
JUSBLAN1
JCFAN
GeForce
8100
JAUDIO1
JUSBPWR2
BAT1
JUSB4 JUSB2 JUSB3
JCMOS
PEX16_1
LAN
BIOS
Super I/O
PCI1
SATA1
JCDIN
SATA3
JAUDIOF
PCI2
Codec
JCOM
SATA2
JPRNT
SATA4
FDD
JSFAN
Note: ■ represents the 1st pin.
4
JPANEL1
GF8100 M2+ TE
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Remove the socket protection cap.
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN. This completes the installation.
Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU
transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.
6
GF8100 M2+ TE
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN: CPU Fan Header
Pin
1
2
3
4
1
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control (By Fan)
JSFAN: System Fan Header
Pin
1
2
3
1
Assignment
Ground
+12V
FAN RPM rate
sense
3
Note:
The JCFAN supports 4-pin head connector. The JSFAN supports 3-pin head connector.
When connecting with wires onto connectors, please note that the red wire is the positive
and should be connected to pin#2, and the black wire is Ground and should be
connected to GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
DIMMA1
DIMMB1
A. Memory Modules
8
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
GF8100 M2+ TE
B. Memory Capacity
DIMM Socket
Location
DDR2 Module
DIMMA1
256MB/512MB/1GB/2GB/4GB
DIMMB1
256MB/512MB/1GB/2GB/4GB
Total Memory
Size
Max is 8GB.
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status
DIMMA1
DIMMB1
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
9
Motherboard Manual
2.4
CONNECTORS AND SLOTS
FDD: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cable.
2
34
1
33
IDE: IDE/ATAPI Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two drives.
10
40
39
2
1
GF8100 M2+ TE
PEX16_1: PCI-Express Gen2 x16 Slot
-
PCI-Express 2.0 compliant.
Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
2X bandwidth over the PCI-Express 1.0 architecture.
PEX16_1
PCI1/PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
11
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
PWR_LED
On/Off
+ + -
9
1
+ SPK
Pin
1
2
3
4
5
6
7
8
12
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
16
8
RST
HLED
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
GF8100 M2+ TE
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
12
24
1
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
3 2
4
1
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note:
Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.
13
Motherboard Manual
JUSB2~JUSB4: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
JUSB2
JUSB4 JUSB3
10
9
2
1
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
NC
Key
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
SATA 1 SATA3
SATA 2 SATA4
1
4
7
14
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
GF8100 M2+ TE
JAUDIOF: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JCDIN: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.
Pin
1
2
3
4
1
4
Assignment
Left Channel
Input
Ground
Ground
Right Channel
Input
15
Motherboard Manual
JCMOS: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
3
1
Pin 1-2 Close:
Normal Operation (default).
3
3
1
1
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
JCOM: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
16
2
10
1
9
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
NC
GF8100 M2+ TE
JPRNT: Printer Port Connector
This header allows you to connect printer port on the PC.
2
1
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
25
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
17
Motherboard Manual
JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V for USB ports at front panel (JUSB2~JUSB4).
Pin 2-3 Close:
JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V STB for USB ports at front panel (JUSB2~JUSB4).
1
JUSBPWR1
1
3
Pin 1-2 close
3
3
1
1
JUSBPWR2
3
Pin 2-3 close
JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse
3
1
3
1
Pin 1-2 close
+5V for PS/2 keyboard and
mouse.
3
1
Pin 2-3 close
+5V STB for PS/2 keyboard
and mouse.
18
GF8100 M2+ TE
CHAPTER 4: RAID FUNCTIONS
4.1
OPERATION SYSTEM
Supports Windows XP Home/Professional Edition, and Windows Vista.
4.2
RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1.
RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment.
This technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
-
Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files.
No capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
19
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.
Features and Benefits
-
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
20
Block 1
Block 2
Block 3
GF8100 M2+ TE
RAID 0+1:
RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.
Features and Benefits
-
-
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
GeForce
8100
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
21
Motherboard Manual
RAID 5:
RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained
by ensuring that the parity information for any given block of data is placed on a
different drive from those used to store the data itself.
Features and Benefits
-
Drives: Minimum 3.
Uses: RAID 5 is recommended for transaction processing and general
purpose service.
Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.
Drawbacks: Individual block data transfer rate same as a single disk.
Write performance can be CPU intensive.
Fault Tolerance: Yes.
Disk 1
DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY
Disk 2
GeForce
8100
DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11
Disk 3
PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12
※
22
For more detailed setup information, please refer to the Driver CD, or go to
http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s Guide.
GF8100 M2+ TE
CHAPTER 5: USEFUL HELP
5.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
23
Motherboard Manual
5.2
SOFTWARE
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
*informa
ti on that you
must provide. Wi thout
this information, you may
not be able to send out
the mail.
This bl ock will show
the i nformation which
would be collected in
the mail .
conditi on
*Describe
of your system.
your area or
*Select
the area cl ose to you.
Provide the e-ma il
address that you would
like to send the copy to.
e the name of
*Provid
the memory module
manufacturer.
Provide the name of
the power suppl y
manufacturer and the
model no.
Send the mail out.
Exi t thi s dialog.
Save these in forma tion to a .txt file
24
GF8100 M2+ TE
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
25
Motherboard Manual
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
AWARD BIOS
Show current BIOS information
AMI BIOS
Online Update function
Clear CMOS function
(Only for AMI BIOS)
(Only for AWARD BIOS)
Save current BIOS
to a .bin file
Update BIOS
with a BIOS file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
After the saving process, finish
dialog will show. Click on OK to
complete the BIOS Backup
procedure.
26
GF8100 M2+ TE
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
27
Motherboard Manual
<Online Update> (for AMI BIOS only)
Automatically download and update the latest BIOS via internet; make sure
that the computer is connected to the internet before using this function.
After clicking on the Online Update
button, the utility will search for the
latest BIOS from internet. If there is
a new BIOS version, the utility will
ask you to download it. Click Yes to
proceed.
If there is no other newer BIOS
version, the utility will also tell you that
your BIOS has been the latest version.
Download completes; the utility will
ask you to program (update) the
BIOS. Click Yes to proceed.
The programming procedure may take minutes, please do not make any
operation during the programming process.
After the updating process, the utility will
ask you to reboot the system. Click OK
to reboot.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. Online Update is completed.
All the information and content above about the T-Series software are subject to be
changed without notice. For better performance, the software is being continuously
updated. The information and pictures described above are for your reference only.
The actual information and settings on board may be slightly different from this manual.
28
GF8100 M2+ TE
5.3
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
29
Motherboard Manual
BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIO-Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.
5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.
6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.
z
z
30
This utility only allows storage device with FAT32/16 format and single
partition.
Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
GF8100 M2+ TE
5.4
AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13
Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)
POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8
Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)
Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3
6, 7
8
Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.
31
Motherboard Manual
5.5
TROUBLESHOOTING
Probable
1.
Solution
No power to the system at all
1.
Make sure power cable is
Power light don’t illuminate, fan
securely plugged in.
inside power supply does not turn 2.
Replace cable.
on.
3.
Contact technical support.
2.
Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard drive is spinning.
module snaps into place.
System does not boot from hard disk
1.
Check cable running from disk to
drive, can be booted from optical drive.
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive.
1.
Back up data and applications
Hard disk can be read and applications
files.
can be used but booting from hard disk 2.
Reformat the hard drive.
is impossible.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
32
GF8100 M2+ TE
This page is intentionally left blank.
33
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGE
GERMAN
Spezifikationen
Sockel AM2+
CPU
AMD Athlon 64 / Athlon 64 FX / Althlon 64
X2 / Sempron / PhenomX3 Prozessoren
(Maximales Watt: 95W)
FSB
Chipsatz
GeForce 8100
Low Pin Count-Schnittstelle
Bietet die häufig verwendeten alten Super
Unterstützt DDR2 533 / 667 / 800
Jeder DIMM unterstützt 256MB/512MB/
1GB/2GB/4GB DDR2.
Integrierter GeForce 8100-Chipsatz
IDE
Integrierter IDE-Controller
SATA
Integrierter Serial ATA-Controller
LAN
Realtek RTL 8201CL PHY
Unterstützt DDR2 1066 (by AM2+ CPU)
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
Max. 512MB gemeinsam benutzter Videospeicher
Unterstützt DX10 / HDCP / PureVideo
Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus
Unterstützt PIO-Modus 0~4,
Datentransferrate bis zu 3 Gb/s
Konform mit der SATA-Spezifikation Version 2.0.
10 / 100 Mb/s Auto-Negotiation
Halb-/ Vollduplex-Funktion
HD
5.1-Kanal-Audioausgabe
Audio-Unters ALC662
Unterstützt High-Definition Audio
tützung
34
Hardware-Überwachung
Dual-Kanal DDR2 Speichermodul
Arbeitsspeich Max. 8GB Arbeitsspeicher
Grafik
Umgebungskontrolle,
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 2
Steckplätze
Unterstützt Hyper Transport 3.0 und PowerNow
Bandbreite von bis zu 5.2 GT/s
E/A-Funktionen.
er
64-Bit-Datenverarbeitung
Unterstützt HyperTransport 3.0 mit einer
ITE8718
Super E/A
Die AMD 64-Architektur unterstützt eine 32-Bit- und
PCI Express Gen2 x16 Steckplatz
x1
PCI-Steckplatz
x2
GF8100 M2+ TE
Spezifikationen
Onboard-Ans
chluss
Diskettenlaufwerkanschluss
x1
Jeder Anschluss unterstützt 2 Diskettenlaufwerke
IDE-Anschluss
x1
Jeder Anschluss unterstützt 2 IDE-Laufwerke
SATA-Anschluss
x4
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
CD-IN-Anschluss
x1
Unterstützt die CD Audio-In-Funktion
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x3
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Rückseiten-E
/A
Platinengröß
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Druckeranschluss Anschluss
x1
Serieller Anschluss
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
VGA-Anschluss
x1
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
DVI-Anschluss
x1
Jeder Anschluss unterstützt 1 Druckeranschluss
175 mm (B) X 245 mm (L)
e
Sonderfunkti Unterstützt RAID 0 / 1 / 5 / 0+1
onen
OS-Unterstü
tzung
Unterstützt Hybrid SLI (by nVIDIA driver)
Biostar behält sich das Recht vor, ohne Ankündigung
Windows XP / VISTA
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
35
Motherboard Manual
FRANCE
SPEC
Socket AM2+
UC
Processeurs AMD Athlon 64 / Athlon 64 FX L'architecture AMD 64 permet le calcul 32 et 64 bits
/ Althlon 64 X2 / Sempron / PhenomX3
Prend en charge Hyper Transport 3.0 et PowerNow
(Watt maximum : 95W)
Bus frontal
Chipset
Prend en charge Hyper Transport 3.0
jusqu'à une bande passante de 5.2 GT/s
GeForce 8100
Interface à faible compte de broches
ITE 8718
Super E/S
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Module de mémoire DDR2 à mode à double voie
Mémoire
Capacité mémoire maximale de 8 Go
principale
Chaque DIMM prend en charge des DDR2
de 256Mo/512Mo/1Go/2Go/4Go
LAN
Realtek RTL 8201CL PHY
Connecteur
embarqué
36
Mémoire vidéo partagée maximale de 512 Mo
Prise en charge DX10 / HDCP / PureVideo
Prend en charge le mode PIO 0~4,
Conforme à la spécification SATA Version 2.0
10 / 100 Mb/s négociation automatique
Half / Full duplex capability
Sortie audio à 5.1 voies
ALC662
Prise en charge de l'audio haute définition
audio HD
Fentes
Les DIMM à registres et DIMM avec code correcteurs
Taux de transfert jusqu'à 3 Go/s.
Prise en
charge
Prend en charge la DDR2 1066 (by AM2+ CPU)
Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133
Contrôleur IDE intégré
Contrôleur Serial ATA intégré
Prend en charge la DDR2 533 / 667 / 800
d'erreurs ne sont pas prises en charge
Graphiques Integré dans la chipset GeForce 8100
SATA
Moniteur de matériel
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 2
IDE
Initiatives de contrôle environnementales,
Fente PCI Express Gen2 x16
x1
Fente PCI
x2
Connecteur de disquette
x1
Connecteur IDE
x1
Chaque connector prend en charge 2 lecteurs de
disquettes
Chaque connecteur prend en charge 2 périphériques
IDE
GF8100 M2+ TE
SPEC
Connecteur SATA
x4
Connecteur du panneau avant
x1
Connecteur Audio du panneau avant x1
Connecteur d'entrée CD
x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB
x3
Connecteur d'alimentation
x1
Chaque connecteur prend en charge 1 périphérique
SATA
Prend en charge les équipements du panneau avant
Prend en charge la fonction audio du panneau avant
Prend en charge la fonction d'entrée audio de CD
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB de
panneau avant
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
Connecteur de Port d'imprimante
x1
Connecteur de Port série
x1
Clavier PS/2
x1
Souris PS/2
x1
E/S du
Port VGA
x1
panneau
Port LAN
x1
arrière
Port USB
x4
Fiche audio
x3
Port DVI
x1
Chaque connector prend en charge 1 Port
d'imprimante
Dimension
s de la
175 mm (l) X 245 mm (H)
carte
Fonctionnal Prise en charge RAID 0 / 1 / 5 / 0+1
ités
Prise en charge Hybrid SLI (by nVIDIA
spéciales
driver)
Support SE Windows XP / VISTA
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
37
Motherboard Manual
ITALIAN
SPECIFICA
Socket AM2+
CPU
Processori AMD Athlon 64 / Athlon 64 FX
/ Althlon 64 X2 / Sempron / PhenomX3
(Watt massimo: 95W)
FSB
Chipset
L’architettura AMD 64 abilita la co mputazione 32
e 64 bit
Supporto di Hyper Transport 3.0 e PowerNow
Supporto di HyperTransport 3.0 fino a
5.2 GT/s di larghezza di banda
GeForce 8100
Interfaccia LPC (Low Pin Count)
ITE 8718
Super I/O Fornisce le funzionalità legacy Super
I/O usate più comunemente.
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 2
Modulo di memoria DDR2 a canale doppio
Memoria
Capacità massima della memoria 8GB
Supporto di DDR2 533 / 667 / 800
principale
Ciascun DIMM supporta DDR2
Supporto di DDR2 1066 (by AM2+ CPU)
256MB/512MB/1GB/2GB/4GB
DIMM registrati e DIMM ECC non sono supportati
Grafica
Integrata nel Chipset GeForce 8100
La memoria video condivisa massima è di 512 MB
Supporto DX10 / HDCP / PureVideo
Modalità Bus Master Ultra DMA 33 / 66 / 100 /
IDE
Controller IDE integrato
133
Supporto modalità PIO Mode 0-4
SATA
Controller Serial ATA integrato
LAN
Realtek RTL 8201CL PHY
Supporto
audio HD
Alloggi
Velocità di trasferimento dei dati fino a 3 Gb/s.
Compatibile specifiche SATA Versione 2.0.
Negoziazione automatica 10 / 100 Mb/s
Capacità Half / Full Duplex
Uscita audio 5.1 canali
ALC662
Supporto audio High-Definit ion (HD)
Alloggio PCI Express Gen2 x16 x1
Alloggio PCI
x2
Connettori Connettore floppy
x1
Ciascun connettore supporta 2 unità Floppy
su scheda Connettore IDE
x1
Ciascun connettore supporta 2 unità IDE
x4
Ciascun connettore supporta 1 unità SATA
Connettore SATA
38
GF8100 M2+ TE
SPECIFICA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore CD-in
x1
Supporta la funzione input audio CD
Collettore ventolina CPU
x1
Collettore ventolina sistema
x1
Collettore cancellaz ione CMOS
x1
Connettore USB
x3
Connettore alimentazione
x1
Alimentazione ventolina CPU (con funzione Smart
Fan)
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB
pannello frontale
(24 pin)
Connettore alimentazione
x1
(4 pin)
Connettore Porta stampante
x1
Connettore Porta seriale
x1
Tastiera PS/2
x1
Mouse PS/2
x1
I/O
Porta VGA
x1
pannello
Porta LAN
x1
posteriore Porta USB
x4
Dimension
i scheda
Connettore audio
x3
Porta DVI
x1
Ciascun connettore supporta 1 Porta stampante
175 mm (larghezza) x 245 mm
(altezza)
Caratterist Supporto RAID 0 / 1 / 5 / 0+1
iche
Supporto Hybrid SLI (by nVIDIA
speciali
driver)
Sistemi
operativi
supportati
Biostar si riserva il diritto di aggiungere o
Windows XP / VISTA
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
39
Motherboard Manual
SPANISH
Especificación
Conector AM2+
CPU
La arquitectura AMD 64 permite el procesado de 32 y
Procesadores AMD Athlon 64 / Athlon 64 64 bits
FX / Athlon 64 X2 / Sempron / PhenomX3 Soporta las tecnologías Hyper Transport 3.0 y
(Vatio máximo: 95W)
FSB
Conjunto
de chips
PowerNow
Admite HyperTransport 3.0 con un ancho
de banda de hasta 5.2 GT/s
GeForce 8100
Interfaz de cuenta Low Pin
ITE 8718
Súper E/S
Le ofrece las funcionalidades heredadas
de uso más común Súper E/S.
Módulo de memoria DDR2 de canal Doble
Memoria
Capacidad máxima de memoria de 8GB
principal
Cada DIMM admite DDR de 256MB/
GeForce 8100
Admite DX10 / HDCP / PureVideo
SATA
Controlador ATA Serie Integrado
Red Local
Realtek RTL 8201CL PHY
40
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s
Funciones Half / Full dúplex
Salida de sonido de 5.1 canales
ALC662
Soporte de sonido Alta Definición
Ranura PCI Express Gen2 x16
X1
Ranura PCI
X2
Conectores Conector disco flexible
en placa
ECC
Memoria máxima de vídeo compartida de 512 MB
Controlador IDE integrado
Ranuras
Admite DDR2 de 1066 (by AM2+ CPU)
Integrados en el conjunto de chips
IDE
sonido HD
Admite DDR2 de 533 / 667 / 800
No admite DIMM registrados o DIMM compatibles con
512MB/1GB/2GB/4GB
Soporte de
Monitor hardware
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 2
Gráficos
Iniciativas de control de entorno,
X1
Cada conector soporta 2 unidades de disco flexible
Conector IDE
X1
Cada conector soporta 2 dispositivos IDE
Conector SATA
X4
Cada conector soporta 1 dispositivos SATA
GF8100 M2+ TE
Especificación
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Conector de entrada de CD
X1
Soporta función de entrada de sonido de CD
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X1
Cabecera de borrado de CMOS
X1
Conector USB
X3
Conector de alimentación
X1
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Conector Puerto de impresora
X1
Conector Puerto serie
X1
Teclado PS/2
X1
Ratón PS/2
X1
Panel
Puerto VGA
X1
trasero de
Puerto de red local
X1
E/S
Puerto USB
X4
Conector de sonido
X3
Puerto DVI
X1
Tamaño de
la placa
175 mm. (A) X 245 Mm. (H)
Funciones
Admite RAID 0 / 1 / 5 / 0+1
especiales
Admite Hybrid SLI (by nVIDIA driver)
Soporte de
sistema
operativo
Cada conector soporta 1 Puerto de impresora
Windows XP / VISTA
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
41
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
Socket AM2+
CPU
A arquitectura AMD 64 permite uma computação de
Processadores AMD Athlon 64 / Athlon 64 32 e 64 bits
FX / Althlon 64 X2 / Sempron / PhenomX3 Suporta as tecnologias Hyper Transport 3.0 e
(Watt máximo: 95W)
FSB
Chipset
Especificaç
ão Super
I/O
Memória
principal
Placa
gráfica
PowerNow
Suporta a tecnologia HyperTransport 3.0
com uma largura de banda até 5.2 GT/s
GeForce 8100
ITE 8718
Interface LPC (Low Pin Count).
Proporciona as funcionalidades mais
Iniciativas para controlo do ambiente
utilizadas em termos da especificação
Monitorização do hardware
Super I/O.
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x 2
Módulo de memória DDR2 de canal duplo
Capacidade máxima de memória: 8 GB
Suporta módulos DDR2 533 / 667 / 800
Cada módulo DIMM suporta uma
Suporta módulos DDR2 1066 (by AM2+ CPU)
memória DDR2 de 256MB/512MB/
Os módulos DIMM registados e os DIMM ECC não são
1GB/2GB/4GB
suportados
Memória de vídeo máxima partilhada: 512 MB
Integrada no chipset GeForce 8100
IDE
Controlador IDE integrado
SATA
Controlador Serial ATA integrado
LAN
Realtek RTL 8201CL PHY
Suporta as funções DX10 / HDCP / PureVideo
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3 Gb/s.
Compatibilidade com a especificação SATA versão 2.0.
Auto negociação de 10 / 100 Mb/s
Capacidade semi/full-duplex
Suporte
para áudio
de alta
Saída de áudio de 5.1 canais
ALC662
Suporta a especificação High-Definition Audio
definição
Ranhuras
Ranhura PCI Express Gen2 x16
x1
Ranhura PCI
x2
Conectores Conector da unidade de disquetes
x1
Cada conector suporta 2 unidades de disquetes
na placa
Conector IDE
x1
Cada conector suporta 2 dispositivos IDE
Conector SATA
x4
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
42
GF8100 M2+ TE
ESPECIFICAÇÕES
Conector de áudio frontal
x1
Conector para entrada de CDs
x1
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema x1
Conector para limpeza do CMOS
x1
Conector USB
x3
Conector de alimentação
x1
Suporta a função de áudio no painel frontal
Suporta a entrada de áudio a partir de CDs
Alimentação da ventoinha da CPU (com a função
Smart Fan)
Alimentação da ventoinha do sistema
Cada conector suporta 2 portas USB no painel frontal
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Entradas/S
aídas no
painel
traseiro
Tamanho
da placa
Conector da para impressora
x1
Conector da Porta série
x1
Teclado PS/2
x1
Rato PS/2
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Tomada de áudio
x3
Porta DVI
x1
Cada conector suporta 1 Porta para impressora
175 mm (L) X 245 mm (A)
Característi Suporta as funções RAID 0 / 1 / 5 / 0+1
cas
Suporta as funções Hybrid SLI (by nVIDIA
especiais
driver)
Sistemas
operativos
suportados
A Biostar reserva-se o direito de adicionar ou remover
Windows XP / VISTA
suporte para qualquer sistema operativo com ou sem
aviso prévio.
43
Motherboard Manual
POLISH
SPEC
Socket AM2+
Procesor
AMD Athlon 64 / Athlon 64 FX / Althlon 64
X2 / Sempron / PhenomX3 Procesory
(Maksymalny Watt: 95W)
FSB
Chipset
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
bitowe
Obsługa Hyper Transport 3.0 oraz PowerNow
Obsługa HyperTransport 3.0 o szerokości
pasma do 5.2 GT/s
GeForce 8100
Gniazda DDR2 DIMM x 2
Moduł pamięci DDR2 z trybem podwójnego kanału
Pamięć
Maks. wielkość pamięci 8GB
Obsługa DDR2 533 / 667 / 800
główna
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR2 1066 (by AM2+ CPU)
256MB/512MB/1GB/2GB/4GB DDR2
Brak obsługi Registered DIMM oraz ECC DIMM
Interfejs Low Pin Count
ITE 8718
Super I/O
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne
Monitor H/W
funkcje Super I/O.
Funkcja ITE "Smart Guardian"
Maks. wielkość współdzielonej pamięci video wynosi
Grafika
Zintegrowana w chipsecie GeForce 8100
512 MB
Obsługa DX10 / HDCP / PureVideo
IDE
Zintegrowany kontroler IDE
SATA
Zintegrowany kontroler Serial ATA
LAN
Realtek RTL 8201CL PHY
Obsługa
audio HD
Gniazda
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
10 / 100 Mb/s z automatyczną negocjacją szybkości
Działanie w trybie połowicznego / pełnego dupleksu
5.1 kanałowe wyjście audio
ALC662
Obsługa High-Definition Audio
Gniazdo PCI Express Gen2 x16
x1
Gniazdo PCI
x2
Złącza
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 napędy dyskietek
wbudowan
Złącze IDE
x1
Każde złącze obsługuje 2 urządzenia IDE
e
Złącze SATA
x4
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
44
GF8100 M2+ TE
SPEC
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wejścia CD
x1
Obsługa funkcji wejścia audio CD
Złącze główkowe wentylatora procesora
Zasilanie wentylatora procesora (z funkcją Smart Fan)
x1
Złącze główkowe wentylatora
Zasilanie wentylatora systemowego
systemowego x1
Złącze główkowe kasowania CMOS x1
Złącze USB
x3
Każde złącze obsługuje 2 porty USB na panelu
przednim
Back Panel
I/O
Wymiary
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Złącze Port drukarki
x1
Złącze Port szeregowy
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Gniazdo audio
x3
Port DVI
x1
Każde złącze obsługuje 1 Port drukarki
175 mm (S) X 245 mm (W)
płyty
Funkcje
Obsługa RAID 0 / 1 / 5 / 0+1
specjalne
Obsługa Hybrid SLI (by nVIDIA driver)
Obsluga
systemu
operacyjne
go
Biostar zastrzega sobie prawo dodawania lub
Windows XP / VISTA
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
45
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(централь
ный
процессор
)
FSB
Набор
микросхем
Гнездо AM2+
Процессоры AMD Athlon 64 / Athlon 64
FX / Althlon 64 X2 / Sempron / PhenomX3
(Максимальный ватт: 95W)
пропускной способностью до 5.2 GT/s
GeForce 8100
Модуль памяти с двухканальным режимом DDR2
Основная
Максимальная ёмкость памяти 8 ГБ
память
Каждый модуль DIMM поддерживает
256МБ/512МБ/1ГБ/2ГБ/4ГБ DDR2
SATA
Локальная
сеть
Поддержка DDR2 1066 (by AM2+ CPU)
Не поддерживает зарегистрированные модули
Интерфейс с низким количеством выводов
Обеспечивает наиболее используемые
действующие функциональные
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Guardian" (Интеллектуальная
возможности Super I/O.
IDE
Поддержка DDR2 533 / 667 / 800
DIMM and ECC DIMM
ITE 8718
Графика
Поддержка Hyper Transport 3.0 и PowerNow
Поддержка HyperTransport 3.0 с
Слоты DDR2 DIMM x 2
Super I/O
Архитектура AMD 64 разрешать обработка данных
на 32 и 64 бит
защита)
Встроенная в набор микросхем GeForce
8100
Максимальная совместно используемая видео
память составляет 512 МБ
Поддержка DX10 / HDCP / PureVideo
Встроенное устройство управления
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133
встроенными интерфейсами устройств Поддержка режима PIO 0~4,
Встроенное последовательное
скорость передачи данных до 3 гигабит/с.
устройство управления ATA
Соответствие спецификации SATA версия 2.0.
Автоматическое согласование 10 / 100 Мб/с
Realtek RTL 8201CL PHY
Частичная / полная дуплексная способность
Звуковая
поддержка
жесткого
Звуковая поддержка High-Definition
ALC662
5.1канальный звуковой выход
диска
Слоты
Встроенны
й разъём
46
Слот PCI Express Gen2 x16
x1
Слот PCI
x2
Разъём НГМД
x1
Разъём IDE
x1
Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей
GF8100 M2+ TE
СПЕЦ
Разъём SATA
x4
Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
Входной звуковой разъём
x1
Поддержка звуковых функций на лицевой панели
Разъём ввода для CD
x1
Поддержка функции ввода для CD
Контактирующее приспособление
Источник питания для вентилятора центрального
вентилятора центрального
процессора (с функцией интеллектуального
процессора
x1
Контактирующее приспособление
вентилятора системы
x1
вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB-разъём
x3
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Разъём Порт подключения
Задняя
панель
средств
ввода-выв
ода
Размер
панели
Каждый разъём поддерживает 2 USB-порта на
лицевой панели
Каждый разъём поддерживает 1 Порт подключения
принтера
x1
Разъём Последовательный порт
x1
Клавиатура PS/2
x1
Мышь PS/2
x1
Порт VGA
x1
Порт LAN
x1
USB-порт
x4
принтера
Гнездо для подключения
наушников
x3
Порт DVI
x1
175 мм (Ш) X 245 мм (В)
Специальн
ые
техническ
Поддержка RAID 0 / 1 / 5 / 0+1
ие
Поддержка Hybrid SLI (by nVIDIA driver)
характери
стики
Поддержк
а OS
Biostar сохраняет за собой право добавлять или
Windows XP / VISTA
удалять средства обеспечения для OS с или без
предварительного уведомления.
47
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪AM2+‬ﻡﻘﺒﺲ‬
‫وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪AMD Athlon 64 / Athlon 64 FX / Sempron /‬ﻡﻌﺎﻟﺠﺎت‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫اﻟﻤﺮآﺰیﺔ‬
‫‪PhenomX3 / Althlon 64 X2‬‬
‫‪ PowerNow‬و ‪Hyper Transport 3.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)و‪: 95‬ﻗﺼـــﻮى واط(‬
‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ‪ 5.2 GT/s‬ﺑﺘﺮدد یﺼﻞ إﻟﻰ‪HyperTransport 3.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪GeForce 8100‬‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪Super I/O‬‬
‫‪ITE 8718‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺡﺎﻟﺔ اﻷﺟﻬﺰة‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫ﻋﺪد‪2‬‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻡﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﺑﺎیﺖ و‪ /1‬و‪ /2‬و‪ 4‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬
‫‪ GeForce 8100‬ﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻡﺘﻜﺎﻡﻞ‪IDE‬ﻡﺘﺤﻜﻢ‬
‫‪SATA‬‬
‫ﻡﺘﻜﺎﻡﻞ‪Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪Realtek RTL 8201CL PHY‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫ﻡﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR2‬وﺡﺪة ذاآﺮة‬
‫ﺳﻌﺎت ‪ 800 / 667 / 533‬ﻡﻴﺠﺎ ﺑﺎیﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫ﺳﻌﺎت ‪ 1066‬ﻡﻴﺠﺎ ﺑﺎیﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫)‪(DDR2 1066 is by AM2+ CPU‬‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﻡﻴﺠﺎ ﺑﺎیﺖ‪512‬أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ‬
‫‪DX10 / HDCP / PureVideo‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫ﺟﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪3.‬ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ‬
‫‪ 2.0.‬اﻹﺹﺪار ‪SATA‬ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻡﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬
‫‪ALC662‬‬
‫اﻟﺘﻌﺮیﻒ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻡﻦ‬
‫ﻓﺘﺤﺔ ‪PCI Express Gen2 x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد‪2‬‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ‬
‫اﻟﻠﻮﺡﺔ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫‪IDE‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺟﻬﺰة‬
‫ﻡﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد‪4‬‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺡﺪ ﻡﻦ أﺟﻬﺰة‬
‫اﻟﻔﺘﺤﺎت‬
‫‪48‬‬
‫‪GF8100 M2+ TE‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬
‫اﻟﻠﻮﺡﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﺡﺠﻢ اﻟﻠﻮﺡﺔ‬
‫ﻡﺰایﺎ ﺥﺎﺹﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪49‬‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫ﻋﺪد ‪1‬‬
‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫وﺹﻠﺔ ﻡﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪3‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺡﺔ ﻡﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪ‪3‬‬
‫ﻡﻨﺎﻓﺬ ‪DVI‬‬
‫ﻋﺪد ‪1‬‬
‫ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫‪ 175‬ﻡﻢ )ﻋﺮض( ‪ 245 X‬ﻡﻢ )ارﺗﻔﺎع(‬
‫‪RAID 0 / 1 / 5 / 0+1‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)‪Hybrid SLI (by nVIDIA driver‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪Windows XP / VISTA‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫ﺑﺪون إﺥﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
Socket AM2+
CPU
FSB
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
AMD Athlon 64 / Athlon 64 FX / Althlon 64 能です
X2 / Sempron / PhenomX3 プロセッサ
ハイパートランスポート3.0とクールアンドクワイアットを
(最高のワット: 95W)
サポートします
5.2 GT/sのバンド幅までハイパートランスポ
ート3.0をサポートします
チップセッ
GeForce 8100
ト
DDR2 DIMMスロット x 2
デュアル チャンネルモードDDR2メモリモジュール
メインメモ
最大メモリ容量8GB
DDR2 533 / 667 / 800 をサポート
リ
各DIMMは 256MB/512MB/1GB/2GB/4GB DDR2 1066 をサポート (by AM2+ CPU)
DDR2をサポート
登録済みDIMMとECC DIMMはサポートされません
低ピンカウントインターフェイス
ITE 8718
Super I/O
もっとも一般に使用されるレガシーSuper I/O
機能を採用しています。
グラフィッ
最大の共有ビデオメモリは512MBです
GeForce 8100チップセットに統合
統合IDEコントローラ
SATA
統合シリアルATAコントローラ
LAN
Realtek RTL 8201CL PHY
H/Wモニター
ITEの「スマートガーディアン」機能
DX10 / HDCP / PureVideo のサポート
クス
IDE
環境コントロールイニシアチブ、
Ultra DMA 33 / 66 / 100 / 133バスマスタモード
PIO Mode 0~4のサポート、
最高3Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
10 / 100 Mb/秒のオートネゴシエーション
半/全二重機能
HDオーディ
オのサポー
5.1チャンネルオーディオアウト
ALC662
ハイデフィニションオーディオのサポート
ト
PCI Express Gen2 x16スロット
x1
PCIスロット
x2
オンボード
フロッピーコネクタ
x1
各コネクタは2つのフロッピードライブをサポートします
コネクタ
IDEコネクタ
x1
各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ
x4
各コネクタは1つのSATAデバイスをサポートします
スロット
50
GF8100 M2+ TE
仕様
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CDインコネクタ
x1
CDオーディオイン機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x3
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
電源コネクタ(24ピン)
背面パネル
I/O
ボードサイ
x1
電源コネクタ(4ピン)
x1
プリンタポートコネクタ
x1
シリアルポートコネクタ
x1
PS/2キーボード
x1
PS/2マウス
x1
VGAポート
x1
LANポート
x1
USBポート
x4
オーディオジャック
x3
DVIポート
x1
各コネクタは1つのプリンタポートをサポートします
175 mm (幅) X 245 mm (高さ)
ズ
特殊機能
RAID 0 / 1 / 5 / 0+1 のサポート
Hybrid SLI のサポート(by nVIDIA driver)
OSサポート Windows XP / VISTA
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
2008/10/06
51