Extron electronics | DMS 3600 | Setup guide | Extron electronics DMS 3600 Setup guide

Setup Guide
Matrix Switchers
DMS 1600
DMS 3600
Configurable Digital Video Matrix Switchers
N
Extron USA - West
Headquarters
+800.633.9876
Inside USA and
Canada Only
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
+800.633.9876
Inside USA and
Canada Only
+800.3987.6673
Inside Europe Only
+800.7339.8766
Inside Asia Only
+81.3.3511.7655
+400.883.1568
+81.3.3511.7656 FAX Inside China Only
+31.33.453.4040
+65.6383.4400
+1.919.863.1794
+31.33.453.4050 FAX +65.6383.4664 FAX
+1.714.491.1500
+1.919.863.1797 FAX
+1.714.491.1517 FAX
Extron China
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
+86.21.3760.1568
+86.21.3760.1566
FAX
© 2010 Extron Electronics All rights reserved. www.extron.com
68-1829-50 Rev. B
12 10
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in the
literature provided with the equipment.
This symbol is intended to alert the user of the presence
of uninsulated dangerous voltage within the product’s
enclosure that may present a risk of electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for
future reference.
Follow Warnings • Follow all warnings and instructions marked
on the equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are
not recommended by the equipment manufacturer because
they may be hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et la
maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans
le boîtier de l’appareil de  tensions dangereuses non
isolées posant des risques d’électrocution.
Attention
Lire les instructions • Prendre connaissance de toutes les
consignes de sécurité et d’exploitation avant d’utiliser le
matériel.
Conserver les instructions • Ranger les consignes de sécurité afin
de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements
et consignes marqués sur le matériel ou présentés dans la
documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation
ni d’outils non recommandés par le fabricant du matériel car cela
risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im Lieferumfang
enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung)
geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses Produktes
gefährliche Spannungen, die nicht isoliert sind und die
einen elektrischen Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten
Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen
Sicherheit des Produktes sollten Sie aufbewahren, damit Sie im
Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle
Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder
Zusatzgeräte, die nicht ausdrücklich vom Hersteller empfohlen
wurden, da diese eine Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre
instrucciones importantes de operación y mantenimiento
(o cambio de partes) que se desean destacar en el
contenido de la documentación suministrada con
los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de
seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario,
deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios
que no sean especificamente recomendados por el fabricante,
ya que podrian implicar riesgos.
Warning
Power sources • This equipment should be operated only from the
power source indicated on the product. This equipment is intended
to be used with a main power system with a grounded (neutral)
conductor. The third (grounding) pin is a safety feature, do not
attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely,
remove all power cords from the rear of the equipment, or the
desktop power module (if detachable), or from the power source
receptacle (wall plug).
Power cord protection • Power cords should be routed so that they
are not likely to be stepped on or pinched by items placed upon or
against them.
Servicing • Refer all servicing to qualified service personnel. There
are no user-serviceable parts inside. To prevent the risk of shock,
do not attempt to service this equipment yourself because opening
or removing covers may expose you to dangerous voltage or other
hazards.
Slots and openings • If the equipment has slots or holes in the enclosure,
these are provided to prevent overheating of sensitive components
inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is
incorrectly replaced. Replace it only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source
d’alimentation indiquée sur l’appareil. Ce matériel doit être utilisé
avec une alimentation principale comportant un fil de terre (neutre).
Le troisième contact (de mise à la terre) constitue un dispositif de
sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans
danger, déconnectez tous les cordons d’alimentation de l’arrière de
l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou
encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons
d’alimentation de manière à ce que personne ne risque de marcher
dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de
réparation-maintenance par un technicien qualifié. Aucun des éléments
internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger
d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même
à ces opérations car l’ouverture ou le retrait des couvercles risquent de
l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des
orifices, ceux-ci servent à empêcher les composants internes sensibles
de surchauffer. Ces ouvertures ne doivent jamais être bloquées par
des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de
la batterie. Remplacer uniquement avec une batterie du meme type ou
d’un ype equivalent recommande par le constructeur. Mettre au reut
les batteries usagees conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt
angegebene Stromquelle betrieben werden. Dieses Gerät wurde für
eine Verwendung mit einer Hauptstromleitung mit einem geerdeten
(neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen
Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht
umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu
trennen, sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus
der externen Stomversorgung (falls dies möglich ist) oder aus der
Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß
sie nicht im Weg liegen und niemand darauf treten kann oder Objekte
darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des
Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks
versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim
Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags
und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im
Gehäuse aufweist, dienen diese zur Vermeidung einer Überhitzung
der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals
von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen
oder einen vergleichbaren Batterietyp, der auch vom Hersteller
empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den
Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a
la fuente/tipo de alimentación eléctrica indicada en el mismo. La
alimentación eléctrica de este equipo debe provenir de un sistema
de distribución general con conductor neutro a tierra. La tercera
pata (puesta a tierra) es una medida de seguridad, no puentearia ni
eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad
la acometida de alimentación eléctrica al equipo, desenchufar
todos los cables de alimentación en el panel trasero del equipo, o
desenchufar el módulo de alimentación (si fuera independiente), o
desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación
eléctrica se deben instalar en lugares donde no sean pisados ni
apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos
de personal calificado. En el interior no hay partes a las que el
usuario deba acceder. Para evitar riesgo de electrocución, no intentar
personalmente la reparación/mantenimiento de este equipo, ya que al
abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos
u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/
alojamiento, es para evitar el sobrecalientamiento de componentes
internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en
la posición incorrecta. Cambiar esta batería únicamente con el mismo
tipo (o su equivalente) recomendado por el fabricante. Desachar las
baterías usadas siguiendo las instrucciones del fabricante.
Extron® Warranty
Extron Electronics warrants this product against defects in materials and
workmanship for a period of three years from the date of purchase. In the event of
malfunction during the warranty period attributable directly to faulty workmanship
and/or materials, Extron Electronics will, at its option, repair or replace said
products or components, to whatever extent it shall deem necessary to restore
said product to proper operating condition, provided that it is returned within the
warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle
East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse,
improper handling care, electrical or mechanical abuse, abnormal operating
conditions, or modifications to the product that were not authorized by Extron.
NOTE:
If it has been determined that the product is defective, please call
Extron and ask for an Applications Engineer at (714) 491-1500 (USA),
31.33.453.4040 (Europe), 65.6383.4400 (Asia), or 81.3.3511.7655 (Japan)
to receive an RA# (Return Authorization number). This will begin the
repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include
the serial number and a description of the problem, as well as the name of the
person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with
respect to the product and its quality, performance, merchantability, or fitness for
any particular use. In no event will Extron Electronics be liable for direct, indirect,
or consequential damages resulting from any defect in this product even if Extron
Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that
some provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Front Panel Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. The Class A limits
are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Front Panel Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
NOTE:
This unit was tested with shielded cables on the peripheral devices.
Shielded cables must be used with the unit to ensure compliance
with FCC emissions limits.
Contents
Introduction........................................1
Remote Control................................11
About this Guide.................................1
About the DMS 1600 and
DMS 3600..........................................2
Configurability....................................3
Selected SIS Commands....................11
Establishing a Network
(Ethernet) Connection..................11
Establishing a USB Port
Connection....................................12
Host-to-Switcher instructions.......13
Command/Response Table
for SIS Commands.........................14
Installing and Starting the
Control Program.............................18
Installing the Program..................18
First-time Connection
Considerations..............................19
Starting the Program....................20
Accessing the HTML Pages...............22
Configuring for Network
Communication............................22
Loading the Start-up Page...........23
Installation..........................................5
Rear Panel............................................5
A Note on I/O Boards......................5
Making Connections.......................7
Front Panel..........................................8
Front Panel Operations.....................9
Creating a Tie......................................9
Viewing Ties
(and Muting Outputs)......................9
Saving or Recalling a Preset.............10
Locking Out the Front Panel
(Executive Mode)............................10
Maintenance and Modifications..25
Removing and Installing
an I/O Board or Blank Panel...........25
Removing and Installing
a Power Supply Module.................27
Removing and Installing
a Fan................................................29
DMS 1600 and DMS 3600 • Contents
i
Introduction
This section gives an overview of the DMS 1600 and DMS 3600 and
describes their features. Topics that are covered include:
• About this Guide
• About the DMS 1600 and DMS 3600
About this Guide
NOTES: • For more information on any subject in this guide, see
the DMS 1600 and DMS 3600 User Guide, available on
the Extron DVD or at www.extron.com.
• Throughout this guide, both products are referred to as
"DMS matrix switchers" unless a significant difference
is noted in their features or operation.
This setup guide helps you to easily and quickly set up and configure
your Extron DMS 1600 and DMS 3600 switcher. Step by step
instructions show you how to:
• Connect the hardware
• Perform basic operations
• Use both the front panel controls and selected
Simple Instruction Set (SIS™) commands
• Load and start the Matrix Switchers Control Program
• Connect to the built-in HTML pages, which you can use to operate
the switcher
• Replace the input/output (I/O) boards, power supplies, and fans
ii
DMS 1600 and DMS 3600 • Contents
DMS 1600 and DMS 3600 • Introduction
1
About the DMS 1600 and DMS 3600
Configurability
A
B
D
A
B
C
D
A
B
C
D
A
B
17 - 20
A
B
21 - 24
A
B
A
B
A
B
A
B
A
B
A
B
1-4
D
C
25 - 28
B
9 - 12
C
29- 32
B
A
DVI-D INPUTS
33 - 36
A
13- 16
The DMS 1600 and DMS 3600 (see figure 1) are configurable matrix
switchers that distribute DVI signals. I/O boards route signals that
are compatible with all Extron DVI video product lines. The matrix
switcher routes any input signal to any combination of outputs.
The matrix switcher can route multiple input/output configurations
simultaneously.
DVI-D OUTPUTS
C
D
C
D
C
D
C
D
C
D
C
D
C
D
C
D
C
D
FAN ASSEMBLY
5-8
DVI Equipped
PCs
Compact HDTV
Camera Systems
FAN ASSEMBLY
HD Camera
FOXBOX Rx DVI
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
DVI-D INPUTS
DVI-D INPUTS
DVI-D INPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
REMOTE
LAN
RS232/RS422
ACT LINK
PRIMARY POWER SUPPLY
HDTV Monitors
MODE
ON
POWER
12V
1.0A MAX
DVI-D
MODE
Digital Monitors
DVI Projectors
RESET
REDUNDANT POWER SUPPLY
OVER OVER
FIBER
ALARM
FIBERALARM
1 2
FOXBOX 4G Rx DVI
Tx Rx
Tx Rx
FOXBOX 4G Tx DVI
PRIMARY
1 2
1 2
100-240V
50/60Hz
1.2A MAX.
ANAHEIM, CA
FOXBOX Tx DVI
POWER
12V
1.0A MAX
MODE
ON
DVI-D OUTPUT
POWER
12V
1.0A MAX
DVI-D INPUT
AUDIO
RS-232
OVER FIBER ALARM
AUDIO
Extron
DMS 3600
Analog Monitor
Modular DVI Matrix Switcher
Tx Rx
1 2
FOXBOX 4G
Rx DVI
FOXBOX
4G Tx DVI Tx Rx
1 2
By adding or removing I/O boards within certain rules that are
detailed in "Configurability rules", below, you can expand and
contract the DMS 1600 and DMS 3600 from a 4-input by 4-output
matrix to up to:
Configurability rules
• The top slot (slot 1) MUST contain a 4x4 DVI input and output
board.
• The next slot (slot 2) can contain any of the three board types
(a 4x4 DVI input and output board, a 4 DVI input board, or a
4 DVI output board).
• After you insert a 4 DVI input board or a 4 DVI output board, all
active boards underneath it MUST be the same type.
ADJUST
INPUTS
2
3
4
5
6
MUTE
AUTO
IMAGE
SIZE
BRIGHT
/CONT
DETAIL
MENU
FREEZE
PIP
PRESET
POSITION
COLOR
/TINT
ZOOM
/PAN
NEXT
7
CONFIG
UPS 507
UNVERSAL SIGNAL PROCESSOR
PC
• 4x4 DVI input and output board
• 4 DVI input board
• 4 DVI output board
• A 4x4 DVI input and output board can be followed (in the slot
directly underneath it) by any of the board types.
RS-232
OVER FIBER ALARM
1 2
1
There are three types of I/O boards available:
There are certain rules for configuring the DMS matrix switcher for
proper operation, as detailed below:
100-240V
50/60Hz
1.2A MAX.
INPUTDVI-D OUTPUT AUDIO AUDIORS-232
RS-232
• The DMS 1600 can include up to four I/O boards.
• The DMS 3600 can include up to nine I/O boards.
• DMS Matrix 1600 — A 16-input by 16-output matrix
• DMS Matrix 3600 — A 36-input by 36-output matrix
REDUNDANT
POWER
12V
1.0A MAX
The DMS 1600 and DMS 3600 are assembled from I/O boards.
USP 507
• If you install a blank panel, all slots under it MUST contain blank
panels (you cannot skip a slot).
Figure 1. Typical DMS 1600 Application
The matrix switcher can be remotely controlled via its Ethernet LAN
port, a serial port, or a USB port using either the Windows-based
Extron Matrix Switchers Control Program or the SIS.
The switcher has two internal, hot-swappable 100 VAC to 240 VAC,
50-60 Hz, 175-watt power supplies that provide worldwide power
compatibility and reliability.
2
DMS 1600 and DMS 3600 • Introduction
DMS 1600 and DMS 3600 • Introduction
3
Installation
This section describes installation of the DMS matrix switchers,
including connections and features. Topics that are covered include:
• Rear Panel
• Front Panel
Rear Panel
A Note on I/O Boards
See figure 2. Each I/O board is identified by the input and output
connector numbers supported by the board position. The input and
output numbers on the boards are identified as locations A through
D.
Location A
Input
Location A
Input 1
OUT
IN
1-4
A
Input 2
OUT
OUT
IN
A
5-8
B
DVI-D INPUTS
OUT
B
A
ANAHEIM, CA
IN
Input 3
A
OUT
IN
C
OUT
C
IN
B
B
DVI-D INPUTS
OUT
Output
Input 4
IN
Output 1
OUT
D
IN
C
C
OUT
IN
A
D
Output 2
OUT
IN
D
Slot 1
(1-4)
F
IN
E
D
DV
OUT
B
E
OUT
IN
F
Slot 2
(5-8)
9 - 12
Slot 3
13 - 16
No board
installed
Slot 4
100-240V
No board
installed
PRIMARY POWER SUPPLY
50/60Hz 1.2A MAX.
Input 5
Input 6
Input 7
Input 8
Figure 2. Arrangement of Inputs and Outputs on the I/O boards
The board position designators correspond to the input and
output numbers served by that position (1 through 4, 5 through 8,
and so on).
The location designators, A through D, correspond to the DVI input or
output, grouped with inputs on the left and outputs on the right and
numbered from left to right.
The input numbers supported by the I/O board in locations
5 through 8 are as follows: A = 5, B = 6, C = 7, D = 8.
4
DMS 1600 and DMS 3600 • Introduction
DMS 1600 and DMS 3600 • Installation
5
1
1-4
8
A
B
A
B
5-8
ANAHEIM, CA
Making Connections
2
DVI-D INPUTS
DVI-D INPUTS
C
D
A
B
C
D
A
B
DVI-D OUTPUTS
DVI-D OUTPUTS
C
D
C
D
a DVI-I Input connectors — Connect DVI cables between these ports
and the DVI output ports of the digital video sources.
b DVI-I Output connectors — Connect DVI displays for the routed
direct digital image.
DVI-D INPUTS
9 - 12
c Remote port — If desired, connect a control system or computer
to the rear panel Remote RS-232/RS-422 port.
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REMOTE
LINK
PRIMARY
100-240V
50-60Hz
1.2A MAX.
LAN
4
REDUNDANT
100-240V
50-60Hz
1.2A MAX.
ACT
3
RS-232/RS-422
5
RESET
13 - 16
DVI-D INPUTS
PRIMARY POWER SUPPLY
REDUNDANT POWER SUPPLY
7
6
7
Figure 3. DMS 1600 Switcher Rear Panel
1
8
1-4
A
B
2
DVI-D INPUTS
C
D
A
B
DVI-D OUTPUTS
d Ethernet port (LAN connector) — If desired, connect a network
C
D
C
D
C
D
C
D
C
D
C
D
C
D
WAN or LAN hub, a control system, or a computer to the Ethernet
RJ-45 port.
FAN ASSIMBLY
D
A
B
C
D
A
B
A
B
17 - 20
A
B
A
B
5-8
C
21 - 24
A
B
A
B
DVI-D INPUTS
13- 16
9 - 12
Network connection — Wire as a patch (straight-through) cable.
DVI-D INPUTS
A
B
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
DVI-D OUTPUTS
Computer or control system connection — Wire the interface
cable as a crossover cable.
NOTE:
The factory default IP address is 192.168.254.254.
e Reset button — Initiates four levels of reset of the matrix switcher.
For different reset levels, press and hold the recessed button while
the switcher is running or while you power up the switcher.
See the DMS 1600 and DMS 3600 User Guide, available on the
Extron DVD or at www.extron.com.
29- 32
25 - 28
FAN ASSIMBLY
DVI-D OUTPUTS
Pin RS-232 Function RS-422 Function
1
— Not used
—
Not used
2
Tx Transmit
Tx– Transmit (–)
5
1
3
Rx Receive
Rx– Receive (–)
4
— Not used
—
Not used
5
Gnd Ground
Gnd Ground
6
— Not used
—
Not used
9
6
7
— Not used
Rx+ Receive (+)
8
— Not used
Tx+ Transmit (+)
9
— Not used
—
Not used
Figure 5. Remote RS-232/RS-422 Output Connector Wiring
33 - 36
f Power connectors — Plug the switcher into two grounded AC
sources.
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
N
PRIMARY POWER SUPPLY
REMOTE
LAN
RS232/RS422
ACT LINK
NOTE:
RESET
REDUNDANT POWER SUPPLY
REDUNDANT
100-240V
50-60Hz
2.5A MAX.
PRIMARY
100-240V
50-60Hz
2.5A MAX.
For reliability, connect the power cord from the
Redundant power connector to either an
uninterruptible power source or to a power source
that is completely independent of the primary power
source.
ANAHEIM, CA
6
7
Figure 4. DMS 3600 Switcher Rear Panel
3
4 5
7
g Primary and Redundant power supply indicator LEDs —
Green — Indicates that the associated power supply is operating
within normal tolerances.
Red — Indicates that the associated power supply is operating
outside the normal tolerances or has failed. See "Removing and
Installing a Power Supply Module" to replace the power supply.
h Fans — See "Removing and Installing a Fan".
6
DMS 1600 and DMS 3600 • Installation
DMS 1600 and DMS 3600 • Installation
7
Front Panel Operations
Front Panel
CONTROL
CONFIG
ENTER
PRESET
VIEW
ESC
PRIMARY
REDUNDANT
POWER SUPPLY
DMS 1600
TMDS DIGITAL MATRIX SWITCHER
This section describes simple DMS matrix switcher operation from the
front panel. Topics that are covered include:
• Creating a Tie
9
10
Figure 6. Front Panel Features
i Configuration port — If desired, connect a control system or
computer to the front panel Configuration port, a mini USB B
port.
j Primary and Redundant Power Supply LEDs —
NOTE:
The meaning of these indicators is identical to the
LEDs on the power supplies (item g).
• Viewing Ties (and Muting Outputs)
• Saving or Recalling a Preset
• Locking Out the Front Panel (Executive Mode)
Creating a Tie
1. Press and release the Esc button to clear any input button, output
button, or control button indicators that may be lit.
2. Press and release the desired input button.
The button lights to indicate the selection.
Green — Indicates that the associated power supply is operating
within normal tolerances.
Red — Indicates that the associated power supply is operating
outside the normal tolerances or has failed. See "Removing and
Installing a Fan" to replace the power supply.
5
3. Press and release the desired output buttons.
The output buttons blink to indicate the potential ties.
3
4
8
ENTER
The Enter button blinks to indicate
the need to confirm the change.
4. Press and release the Enter button. All button indicators turn off.
See figure 2 in the "Installation" section. The input numbers
supported by the I/O board in locations 5 through 8 are as follows:
A = 5, B = 6, C = 7, D = 8.)
Viewing Ties (and Muting Outputs)
1. Press the View button. Output buttons light for outputs that have
no ties established.
NOTE:
If an output button blinks, that output is muted. To
toggle mute on and off, press and hold the output
button for 2 seconds.
2. Press an input button. The buttons for all tied outputs light.
3. Press an output button. The buttons for the tied input and all tied
outputs light.
4. Press the View button again to exit View mode. All input and
output buttons return to an unlit state.
8
DMS 1600 and DMS 3600 • Installation
DMS 1600 and DMS 3600 • Front Panel Operations
9
Saving or Recalling a Preset
1. Save a preset — Press and hold the Preset button until it flashes.
Save a
preset
PRESET
2 seconds
PRESET
Press and hold.
The Preset button blinks.
Recall a preset — Press and release the Preset button.
Recall a
preset
PRESET
PRESET
Press and release.
• Installing and Starting the Control Program
The Preset button lights.
INPUTS
2
3
4
5
This section describes using the remote control features of the
DMS matrix switchers to control the devices. Topics that are covered
include:
• Selected SIS Commands
All input and output buttons with assigned presets light red.
When a preset is saved, the configuration data at
assigned preset locations will be overwritten.
1
Remote Control
• Accessing the HTML Pages
Selected SIS Commands
You can use Simple Instruction Set (SIS) commands for operation and
configuration of the switchers. You can run these commands from
a PC connected to a serial port (item c on page 7), Ethernet port
(item d on page 7), or USB port (item i on page 8) on the switcher.
6 15 16
2. Press and release the desired input or output button.
Establishing a Network (Ethernet) Connection
The button blinks red to indicate that
this preset is selected to save or recall.
1
ENTER
NOTE:
The Enter button blinks
red to indicate the need to
activate the save or recall.
3. Press and release the Enter button.
Locking Out the Front Panel (Executive Mode)
Establish a network connection as follows:
To toggle the lock on and off, simultaneously press and hold the
Enter button and the Esc button until the Preset and View buttons
blink twice (approximately 2 seconds).
Press and hold the Enter and
Esc buttons simultaneously to
toggle executive mode on or off.
C O NT R O L
ENTER PRESET
VIEW
ESC
ENTER PRESET
VIEW
1. Open a TCP socket to port 23 using the IP address of the switcher.
NOTE:
The factory default IP address is 192.168.254.254.
The switcher responds with a copyright message including the
name, firmware version, and part number of the product, and the
current date and time.
C O NT R O L
2 seconds
The first time you connect to the switcher via the LAN
port, you may need to change the default settings (IP
address, subnet mask, and [optional] administrator name
and password) of the controller (see "Configuring for
Network Communication").
ESC
The Preset and View buttons
blink twice to indicate the
mode change.
Release the buttons.
NOTES: • If the switcher is not password-protected, the device
is now ready to accept SIS commands.
• If the switcher is password-protected, a password
prompt appears.
2. If necessary, enter the appropriate password.
If the password is accepted, the switcher responds with Login
User or Login Administrator.
If the password is not accepted, the Password prompt reappears.
10
DMS 1600 and DMS 3600 • Front Panel Operations
DMS 1600 and DMS 3600 • Remote Control
11
Connection timeouts
The Ethernet link times out and disconnects after a designated period
of time of no communications. By default, this timeout value is set
to 5 minutes but the value can be changed (see the "Configure port
timeout SIS command" on page 17.)
NOTE:
Extron recommends leaving the default timeout at
5 minutes and periodically issuing the Query (Q) command
to keep the connection active or disconnecting the socket
and reopening the connection when necessary.
Number of connections
Host-to-Switcher instructions
The switcher accepts SIS commands through its serial port, its USB
port, or its LAN port. SIS commands consist of one or more characters
per command field. They do not require any special characters
to begin or end the command character sequence. Each switcher
response to an SIS command ends with a carriage return and a line
feed (CR/LF = ]), which signals the end of the response character
string. A string is one or more characters.
NOTE:
The table that begins on the next page is a partial
list of SIS commands. For a complete listing, see the
DMS 1600 and DMS 3600 User Guide.
A switcher can have up to 200 simultaneous TCP connections,
including all HTTP sockets and Telnet connections. When the
connection limit is reached, the switcher accepts no new connections
until some have been closed. No error message or indication is
given that the connection limit has been reached. To maximize the
performance of your switcher, keep the number of connections low
and close unnecessary open sockets.
Verbose mode
Telnet connections to a switcher can be used to monitor for changes
that occur on the switcher, such as front panel operations and
SIS commands from other Telnet sockets or a serial port. For a Telnet
session to receive change notices from the switcher, the Telnet session
must be in verbose mode 1 or 3 (see the "Set verbose mode SIS
command" on page 17.) In verbose mode 3, the Telnet socket reports
changes using messages that resemble SIS command responses.
Establishing a USB Port Connection
A standard USB cable and the Extron DataViewer utility, version 2.0 or
newer, can be used for connection to the DMS switcher Configuration
port. The USB cable, available at any local electronics store, should be
terminated on one end with a mini USB B male connector
NOTE:
12
Before you use the USB port for the first time, install the
USB driver on your computer. The simplest way to do this
is to install version 8.0 or newer of the Matrix Switchers
Control Program and then run the Found New Hardware
Wizard (see "Installing the Program" and "First-time
Connection Considerations".)
DMS 1600 and DMS 3600 • Remote Control
DMS 1600 and DMS 3600 • Remote Control
13
14
Command/Response Table for SIS Commands
DMS 1600 and DMS 3600 • Remote Control
Command
ASCII Command
Response
(Host to Unit)
(Unit to Host)
Additional Description
Create ties
NOTES:
• Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%.
• The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
•The ! tie command, the & tie command, and the % tie command can be used interchangeably.
•The ! read tie command, & read tie command, and the % read tie command can be used interchangeably.
Tie input X! to output X@
Example (see Notes, above):
X!*X@!
1*3!
OutX@•InX!•All]
Tie input X! to output X@
Example (see Notes, above):
X!*X@&
10*4&
OutX@•InX!•RGB]
Tie input X! to output X@
Example (see Notes, above):
X!*X@%
7*5%
OutX@•InX!•Vid]
Read output tie
X@&
X@%
X@!
X!]
X!]
X!]
Read output tie
Read output tie
NOTE:
X! = Input number
X@ = Output number
Out03•In01•All]
Out04•In10•RGB]
Out05•In07•Vid]
Tie input X! to output X@.
Tie input 1 to output 3.
Tie input X! to output X@.
Tie input 10 to output 4.
Tie input X! to output X@.
Tie input 7 to output 5.
Input X! is tied to output X@.
Input X! is tied to output X@.
Input X! is tied to output X@.
00 – maximum number of inputs for your configuration (00 = untied)
01 – maximum number of outputs for your configuration
Command
ASCII Command
Response
(Host to Unit)
(Unit to Host)
VmtX@*1]
Mute output X@ (no signal is output).
Read channel mute
X@*1B
X@*0B
X@B
Unmute output X@ (signal is output).
1 = mute on, 0 = mute off.
Global channel mute
1*B
Global channel unmute
0*B
View output mutes
EVM}
VmtX@*0]
X#]
Vmt1]
Vmt0]
X#1X#2 ... X#n]
Channel mute commands
Channel mute
Channel unmute
Additional Description
Mute all outputs.
Unmute all outputs.
Each X# response is the mute status of an
output, starting from output 1.
n = the maximum number of outputs for your
configuration.
Save and recall presets
NOTE: If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
DMS 1600 and DMS 3600 • Remote Control
Save current configuration as a
global preset
Example:
X$,
SprX$]
Command character is a comma.
9,
Spr09]
Save current ties as preset 9.
Recall a global preset
X$.
RprX$]
Command character is a period.
5.
Rpr05]
Recall preset 5, which becomes the current
configuration.
Example:
NOTE:
X@ = Output number
X# = Mute status
X$ = Global preset number
01 – maximum number of outputs for your model
0 = not muted, 1 = muted
01 – 32
15
16
Command
DMS 1600 and DMS 3600 • Remote Control
ASCII Command
Response
(Host to Unit)
(Unit to Host)
Information requests
Information request
I
Request part number
N
Request part number and board
configuration
Query controller firmware
version
Example:
*N
VX%XX^•AX%XX^•SX&1X&2...X&n]
In the response:
VX%XX^ shows the number of available inputs
and outputs for this configuration.
AX%XX^ has no meaning for this product.
SX&1X&2...X&n shows the board type installed in
each slot. n is the highest numbered board in
your system, 4 or 9.
See the DMS 1600 and DMS 3600 User Guide
X*]
for part numbers.
n is the highest numbered board in your
X*.X&1X&2X&3...X&n]
system, 4 or 9
NOTE:
X(]
Q
1.23]
X% = Inputs
X^ = Outputs
X& = Board installed
Total number of inputs for this switcher
Total number of outputs for this switcher
X0 = No board installed
C1 = 4 inputs by 4 outputs
X* = Part number
60-nnnn-nn
X( = Firmware version number to second decimal place (x.xx)
Command
IP setup
Set IP address
Read IP address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set DHCP on or off
Read DHCP on/off status
Set verbose mode
Read verbose mode
DMS 1600 and DMS 3600 • Remote Control
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
NOTE:
Q
ASCII Command
Response
(host to unit)
(unit to host)
EX1)CI}
ECI}
EX1)CS}
ECS}
EX1)CG}
ECG}
EX1!DH}
EDH}
EX1@CV}
ECV}
E0*X1#TC}
E0TC}
E1*X1#TC}
E1TC}
IpiX1)]
Additional Description
The factory-installed controller firmware
version is 1.23 (sample value only).
C2 = 4 inputs by 0 outputs
C3 = 0 inputs by 4 outputs
Additional description
X1)]
IpsX1)]
X1)]
IpgX1)]
X1)]
IdhX1!]
X1!]
VrbX1@]
X1@]
Pti0*X1#]
X1#]
Pti1*X1#]
X1#]
X1) = IP address nnn.nnn.nnn.nnn
X1! = DHCP
0 = off, 1 = on
X1@ = Verbose mode
0 = clear or none (default for Telnet connection)
X1# = Port timeout interval
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
17
Installing and Starting the Control Program
Another way to operate the switcher is via the Windows®-based
Matrix Switchers Control Program. This program is contained on the
Extron Software Products DVD (included with the switcher). Run
this program on a PC connected to a serial port (item c on page 7),
Ethernet port (item d on page 7), or USB port (item i on page 8)
on the switcher. The program must be installed on a Windows-based
computer and cannot be run from the DVD.
NOTE:
For details on operating the program see the “Matrix
Software” section in the DMS 1600 and DMS 3600 User
Guide.
Installing the Program
NOTE:
To run this program while your computer is connected to
the Configuration (USB) port, use version 8.0 or newer of
the Matrix Switchers Control Program.
1. Insert the DVD into the drive. The Extron software DVD window
should appear automatically.
4. Follow the on-screen instructions. The installation program creates
a C:\Program Files\Extron\Matrix_Switchers directory and an
“Extron Electronics\Matrix Switchers” group folder. It installs the
following four programs:
•
•
•
•
MATRIX Switcher+ Control Program
MATRIX Switcher+ Help
Uninstall MATRIX Switcher
Check for Matrix Updates
First-time Connection Considerations
LAN port connection
If you connect your PC to the switcher via the LAN port, and it
is the first time you have done so, you may change the default
settings (IP address, subnet mask, and [optional] administrator name
and password) on the controller (see "Configuring for Network
Communication" for details.)
USB port connection
When you connect your PC to the DMS matrix switcher via the USB
port for the first time, the Found New Hardware Wizard opens.
1
Figure 7. Software DVD Window
NOTE:
If the window does not open automatically, run
Launch.exe from the DVD.
2. Click the Software tab.
3. Scroll to the Matrix Switchers program and click
Install.
Figure 8. Select Matrix Switchers Program
18
DMS 1600 and DMS 3600 • Remote Control
1
Activate the connected USB port for your device as follows:
NOTE:
If you have not installed the latest Matrix Switchers
Control Program, click Cancel and install the program.
Reconnect the switcher to the Configuration port.
1. Select the No, not this time radio button and click Next.
The wizard installs the necessary driver to access the switcher via
the Configuration (USB) port (this may take a few minutes).
DMS 1600 and DMS 3600 • Remote Control
19
2. On the next page that appears, select the Install the
software automatically radio button and click Next. Follow
the on-screen instructions. The wizard assigns the driver necessary
to access the switcher to the connected Configuration (USB) port
(this may take a few minutes).
3. If you selected IP [LAN] in step 2, the IP Connection window
appears.
3. Click Finish to exit the wizard.
NOTE:
You may need to repeat these steps if you
subsequently connect the switcher to a different USB
port on the same computer.
Starting the Program
1. Click Start > Programs > Extron Electronics > Matrix
Switchers > MATRIX Switcher + Control Pgm.
The Comm Port Selection window appears.
Figure 10. IP Connection Window
a. Examine the Matrix IP Address field, which displays the
last Matrix IP address entered.
If necessary, enter the correct IP address in the field.
NOTE:
192.168.254.254 is the factory-specified default
value for this field.
b. If the switcher is password-protected, enter the appropriate
administrator or user password in the Password field.
c. Click Connect. The Matrix Switchers Control Program is ready
for operation.
Figure 9. Comm Port selection Window
2. Choose the comm (serial) port that is connected to the switcher,
USB, or IP [LAN].
NOTE:
For a comm port, check the baud
rate displayed in the Comm Port
Selection window. If you need
to change the baud rate, click the
Baud button and double-click the
desired baud rate.
Click OK.
If you selected a serial port or the USB port in step 2, the Matrix
Switchers Control Program is ready for operation.
20
DMS 1600 and DMS 3600 • Remote Control
DMS 1600 and DMS 3600 • Remote Control
21
Accessing the HTML Pages
NOTE:You must ping the DMS matrix switcher as shown in
step 5 for the IP address change to take place. The
response should show the new IP address, as shown in
the following figure.
Another way to configure and operate the switcher is via its factoryinstalled HTML pages, which are always available and cannot be
erased or overwritten. The HTML pages that are pre-loaded on the
switcher are accessible through its LAN port, connected via a LAN or
WAN, using a web browser such as Microsoft® Internet Explorer® (see
item d on page 7, for connection information.)
Configuring for Network Communication
The first time you connect a PC to a switcher via its LAN port, you
may need to temporarily change the IP settings of the PC in order
to communicate with the controller. Then you must change the
default settings of the controller (IP address, subnet mask, and
[optional] administrator name and password) in order to use the unit
on an intranet (LAN) or on the Internet. After you have set up the
DMS matrix switcher for network communication, you can reset the
PC to its original network configuration.
NOTE:
The computer and the switcher must both be
connected to the same subnet on a LAN (using a
straight-through cable). Alternatively, you can use
a crossover Ethernet cable to connect the controller
directly to the computer.
5. Execute a ping command by entering ping followed by a space
and the new IP address at the command prompt. For example:
ping 10.13.197.7
C:\>ping 10.13.197.7
Pinging 10.13.197.7 with 32 bytes of data:
Reply
Reply
Reply
Reply
from
from
from
from
10.13.197.7:
10.13.197.7:
10.13.197.7:
10.13.197.7:
NOTE:
NOTE:
The switcher must be configured with the factory
default IP address (192.168.254.254) before the ARP
command is executed, as described below.
4. At the PC, access the MS-DOS® command prompt, then enter the
arp –s command. Type in the desired new IP address for the unit
(obtained in step 1) and the MAC address of the unit (from the
rear panel of the unit). For example:
arp –s 10.13.197.7 00-05-A6-03-69-B0 and then press
<Enter>.
After receiving the arp -s command, the controller changes to
the new address and starts responding to the ping requests, as
described in step 5.
DMS 1600 and DMS 3600 • Remote Control
You can reconnect using either Telnet or a web
browser to verify that the update was successful.
arp –d 10.13.197.7 removes 10.13.197.7 from the ARP table
or
arp –d* removes all static IP addresses from the ARP table.
Loading the Start-up Page
NOTES: • If your Ethernet connection to the matrix switcher
is unstable, try turning off the proxy server in your
web browser. In Microsoft Internet Explorer, click
Tools > Internet Options > Connections > LAN
Settings, uncheck the Use a proxy server...
box, and then click OK.
• For details on operating the switcher via HTML
pages, see the "HTML Operation" section in the
DMS 1600 and DMS 3600 User Guide.
1. Start the web browser program.
2. Click in the Address field.
3. Enter the Matrix IP address in the Address field.
NOTE:
22
TTL=128
TTL=128
TTL=128
TTL=128
6. After verifying that the IP address change was successful, enter
and issue the “arp –d” command at the DOS prompt. For example:
2. Obtain the MAC address (UID #) of the switcher from the label
on its rear panel. The MAC address should have this format:
00-05-A6-xx-xx-xx.
3. If the switcher has never been configured and is still set for factory
defaults, go to step 4. If not, perform a mode 4 system reset. For
detailed information on reset modes, see “Reset Operations” in
the DMS 1600 and DMS 3600 User Guide.
time<10ms
time<10ms
time<10ms
time<10ms
Ping statistics for 10.13.197.7:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Use the ARP command to configure the IP address as follows:
1. Obtain a valid IP address for the DMS matrix switcher from the
network administrator.
bytes=32
bytes=32
bytes=32
bytes=32
192.168.254.254 is the factory-specified default value
for this field.
DMS 1600 and DMS 3600 • Remote Control
23
4. Press the keyboard <Enter> key. The switcher checks whether it is
password-protected.
If the switcher is not password-protected, it checks and
downloads the HTML start-up page. The switcher is ready for
operation via HTML remote control.
Maintenance and
Modifications
If the switcher is password-protected, it downloads the Enter
Network Password dialog box.
This section describes repairing and reconfiguring the
DMS matrix switchers by replacing components. Topics that are
covered include:
• Removing and Installing an I/O Board or Blank Panel
• Removing and Installing a Power Supply Module
• Removing and Installing a Fan
Removing and Installing an I/O Board or Blank Panel
Circuit boards can be added or removed to increase or decrease the
I/O configuration (size) of the switcher.
Figure 11. Enter Network Password Dialog Box
NOTE:
A User name entry is not required.
5. Enter the appropriate administrator or user password in the
Password field and click OK.
6. The switcher downloads the HTML start-up page. The switcher is
ready for operation via HTML remote control.
NOTES: • For proper cooling and air flow, boards or blank panels
should be installed in all locations during normal
switcher operations.
• See "A Note on I/O Boards" in the "Installation"
section to understand the different arrangement of
connectors on the I/O boards.
Remove and replace an I/O board or blank panel as follows:
NOTE:
The I/O boards are hot-swappable. You do not need to
power down the switcher to remove an I/O board.
1. For an I/O board, disconnect any connected cables.
2. Rotate the left and right knurled knobs to completely loosen the
captive screws (see figure 13 on the next page).
3. Gently pull on the knurled knobs to loosen the board or panel
from the backplane.
4. Slide the board or panel out of the chassis.
Figure 12. Downloaded Start-up Page
24
DMS 1600 and DMS 3600 • Remote Control
DMS 1600 and DMS 3600 • Maintenance and Modifications
25
Removing and Installing a Power Supply Module
Align the board edges
with the plastic guides.
D
S 44
DV
I
DM
UT
S
C
TP
I-D
D
OU
DV
S 44
I
DM
B
UT
S
C
S
C
TP
I-D
D
OU
DV
S 44
A
DV
CAUTION:
I
DM
B
UT
TP
I-D
OU
LY
DV
D
DV
The two power supply modules (primary power supply and redundant
power supply) are identical and hot-swappable. Each power supply
module has a two-color LED, visible on the rear panel, that indicates
the status of the power supply outputs. If the LED is lit green, the
power supply is operating normally. If the LED is lit red, the supply
has failed and should be replaced at the earliest opportunity. LEDs
with identical meanings are also on the front panel.
PP
A
WER
B
SU
T PO
AN
ND
DU
RE
C
TS
D
PU
I-D
IN
A
D
DV
S 44
B
TP
1-8
I-D
C
B
I-D
LY
IN
PP
9 - 16
DV
A
17 - 24
, CA
EIM
I
C
OU
DV
TS
AH
S
UT
D
IN
B
PU
AN
DV
DM
C
TS
PU
I-D
DV
A
A
WER
SU
Y PO
AR
B
A
IM
PR
D
25 - 32
X.
A MA
1.2
/60
REDUNDANT
Hz
V
50
40
0-2
TS
C
PU
I-D
IN
DV
B
PRIMARY
A
X.
The power supply modules are hot-swappable. You do
not need to power down the switcher to install or remove
either power supply module.
A MA
Hz
1.2
/60
V
50
40
0-2
10
RE
Knurled Knobs
Figure 13. Remove and Install an I/O Board
CAUTION:
NOTE:
IN
RESET
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REMOTE
LINK
LAN
ACT
TRI-LEVEL BI-LEVEL
RS-232/RS-422
10
H
ITC E
SW NC
RE
FE
The DMS matrix switchers use double pole/neutral
fusing. Power must be disconnected before servicing
internal components.
1. Rotate the left and right knurled knobs to completely loosen the
captive screws (see figure 14).
Do not touch the electronic components or the
connectors on the backplane or on the circuit
boards without being electrically grounded.
Handle circuit boards by their edges only.
Electrostatic discharge can damage circuits, even
if you cannot feel, see, or hear it.
D
I
S 44
DV
DM
S
UT
C
S
UT
C
S
UT
C
TP
I-D
D
OU
I
DV
S 44
DV
DM
B
TP
I-D
5. Place the removed board on an anti-static surface or in an antistatic container.
TP
I-D
S
UT
C
TP
D
DV
B
I-D
I-D
OU
LY
PP
A
WER
B
SU
T PO
AN
ND
DU
RE
B
C
TS
D
PU
I-D
IN
A
DV
A
B
C
TS
D
PU
I-D
IN
1-8
9 - 16
DV
A
A
B
C
TS
LY
PU
, CA
EIM
AH
AN
I-D
PP
IN
WER
DV
SU
Y PO
AR
B
IM
17 - 24
PR
A
25 - 32
X.
A MA
1.2
REDUNDANT
Hz
/60
V
50
40
0-2
Align the power
supply edges with
the plastic guides.
PRIMARY
RESET
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REMOTE
LINK
LAN
TRI-LEVEL BI-LEVEL
RS-232/RS-422
10
ACT
8. Gently slide the board or blank panel into the enclosure. For an
I/O board, slide the board toward the front panel until it meets
resistance.
I
S 44
DM
A
DV
C
TS
IN
DV
D
OU
DV
D
DV
7. For an I/O board, align the board with the left and right chassis
guides (above).
I
S 44
DM
B
PU
6. For an I/O board, orient the board to be installed so that
connector A (of either the input group of connectors or the
output group of connectors) is on the left and connector D (of the
same group of connectors) is on the right.
D
OU
DV
A
X.
A MA
Hz
1.2
/60
V
50
40
0-2
H
ITC E
SW NC
RE
FE
10
RE
9. Gently seat the board or panel in the backplane.
10.Tighten the left and right knurled knobs to lock the board or
panel in place. Use a screwdriver to tighten the knurled knobs.
Power
LED
Knurled
Knobs
Figure 14. Remove and Install a Power Supply Module
2. Gently pull on the handle to loosen the power supply from the
backplane.
3. Slide the power supply out of the chassis.
4. Orient the power supply module to be installed with the LED to
the right.
26
DMS 1600 and DMS 3600 • Maintenance and Modifications
DMS 1600 and DMS 3600 • Maintenance and Modifications
27
5. Align the flanges on the power supply module with the left and
right power supply guides.
3. Gently pull on the screws to loosen the fan from the backplane.
4. Slide the fan out of the chassis.
6. Gently slide the power supply module into the enclosure until the
power supply meets resistance.
5. Orient the fan to be installed so that the printing on the back of
the panel is right-side up.
7. Gently seat the power supply in the backplane.
6. Align the flanges on the fan with the top and bottom fan guides.
8. Tighten the left and right knurled knobs to lock the power supply
in place. Use a screwdriver to tighten the knurled knobs.
7. Gently slide the fan into the enclosure until the fan meets
resistance.
8. Gently seat the fan in the backplane.
Removing and Installing a Fan
9. Tighten the top and bottom knurled knobs to lock the fan in
place. Use a screwdriver to tighten the knurled knobs.
The DMS 1600 has a single fan module. The DMS 3600 has two
identical fan modules. The fan modules are hot-swappable. If a fan
fails, it should be replaced at the earliest opportunity.
NOTE:
10.Secure the row identification plate to the fan.
The fans modules are hot-swappable. Either fan can
be removed or installed without powering down the
switcher.
1. Remove and retain the two screws that secure the row
identification plate (identifying the rows of the adjacent DVI input
and output connectors) to the fan. Retain the plate.
2. Rotate the top and bottom knurled knobs to completely loosen
the captive screws (see figure 15).
D
I
S 44
DV
DM
S
C
UT
TP
I-D
D
OU
I
DV
S 44
DV
DM
B
S
C
UT
TP
I-D
D
OU
I
DV
S 44
B
S
C
UT
TP
I-D
D
OU
I
DV
D
S 44
B
S
C
UT
TP
I-D
D
IN
DV
DM
A
OU
LY
DV
C
TS
PU
I-D
DV
DM
A
PP
A
WER
B
SU
T PO
DV
AN
ND
DU
RE
B
C
TS
D
PU
I-D
IN
A
DV
A
B
C
TS
D
PU
I-D
IN
DV
A
B
C
TS
PU
I-D
LY
IN
PP
DV
WER
A
SU
Y PO
AR
B
IM
PR
A
X.
A MA
1.2
REDUNDANT
Hz
/60
V
50
40
0-2
PRIMARY
RESET
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
X.
A MA
Hz
1.2
/60
V
50
40
0-2
H
ITC E
SW NC
RE
FE
10
RE
1-8
Align the fan
module edges with
the plastic guides.
, CA
EIM
AH
25 - 32
17 - 24
AN
9 - 16
REMOTE
LINK
LAN
ACT
TRI-LEVEL BI-LEVEL
RS-232/RS-422
10
Knurled
Knobs
Figure 15. Remove and Install a Fan
28
DMS 1600 and DMS 3600 • Maintenance and Modifications
DMS 1600 and DMS 3600 • Maintenance and Modifications
29
Download PDF