Vision Fitness | R2000 | User manual | ASSEMBLY INSTRUCTIONS

R2000

ASSEMBLY INSTRUCTIONS

To avoid possible damage to this Fitness Cycle, please follow these assembly instructions.

Carefully remove all its parts from the box, lay them out and review the parts list.

If any parts are missing, please call 1-800-335-4348, Ext 12

Before proceeding, find your Fitness Cycle’s serial number, located on the underside of main frame, and enter here:

Refer to this number when calling for service.

I T A L L S T A R T S W I T H A V I S I O N

R2000

Parts Diagram

523

130

125

R2000

Parts

VISION FITNESS R2000 Parts Description

Part # Description

Rear Foot and Seat Support Parts

#106

#182

#184

#91

#96

#186

#121

Rear Foot Assembly

Top Attachment Bolts

Top Attachment Washers

Bolt Plate

Seat Rail Support Post

Support Post Bolts-Bottom

Seat Rail

Count Dimensions

1

4

1

7

1

1

7 20mm L x 8mm D

60mm L x 8mm D

Seat Parts

#115

#137

#136

#195

#196

#110

#182

#184

#133

#520

#523

Seat Frame

Seat Cushion Back

Seat Cushion Bottom

Seat Cushion Bolts

Seat Cushion Bolt Washers

Seat Mount Handlebars

Handlebar Attachment Bolts

Handlebar Attachment Washers

Rubber Seat Rail Cap

Seat Knob

Seat Rail End Cap

Console Parts

#101

#182

#184

153

#75

#88

Console Mast

Console Mast Attachment Bolts

Console Mast Attachment Washers 6

Console

1

6

RPM Sensor Wire

Console Mast Rubber Cover

1

1

1

Other Parts

#152

#199

#130

#125

Pedals

Pedal Straps

Tension Knob and Cable

Tension Knob Bolt

1

1

2

2

4

4

8

1

1

8

1

1

1

1

1

55mm L x 6mm D

20mm L x 8mm D

20mm L x 8mm D

R2000

Assembly

Step 1 • Seat Support and Rear Foot

1: Attach the Seat Rail Support Post (96) to the top of the Rear Foot Assembly

(106) with four Bottom Support Post Bolts (186), four Washers (184) and

Bolt Plate (91). Tighten with a 5mm allen wrench.

Step 2 • Seat Rail

1: Place the Seat Rail (121) on the Seat Rail Support (96). Thread the four

Attachment Bolts (182) with Washers (184) through the top of the Seat

Rail Support (96) into the Seat Rail (121).

2: Slide the Seat Frame (115) onto the Seat Rail (121) from the front of the

Seat Rail. After the Seat Frame (115) is on the Seat Rail (121) insert the

Seat Knob (520) into a hole to prevent the Seat Frame (115) from sliding forward.

3: Slip the Rubber Seat Rail Cap (133) onto the front end of the Seat Rail

(121), slide the Rubber Seat Rail Cap (133) back to expose the three front attachment bolt holes.

4: Place the Seat Rail Assembly (121) into the main frame bracket. Thread the three Attachment Bolts (182) with Washers(184) through the Seat Rail

(121) in the main frame bracket. Tighten all Attachment Bolts (182) securely to the main frame bracket. Slide down the Rubber Seat Rail Cap

(133) until it is flush with the side covers.

5: Place the seat rail end cap over the rear end rail and snap to the top of the seat rail end post.

Note: ALWAYS HOLD THE SEAT KNOB OUT WHEN ADJUSTING THE SEAT

HEIGHT. TURN THE INNER KNOB CLOCKWISE TO LOCK IN PLACE.

184

182

523

96

END CAP

SIDE VIEW

121

FRONT VIEW

R2000

Assembly

Step 3 • Seat Assembly

1: Secure the Seat Mount Handlebars (110) to the Seat Frame (115) with four

Seat Attachment Bolts (182) and Washers (184).

2: When mounting the Seat Cushion Bottom (136), you have two sets of holes to choose from. Using the rear set of holes is recommended for most people. For a smaller person, you may choose to use the forward set of bolt holes. Mount the Seat Cushion Bottom (136) to the Seat Frame

(115) with four of the Seat Cushion Bolts (195) and Seat Cushion Bolt

Washers (196). Do not fully tighten any bolt until all four bolts are started.

3: Mount the Seat Cushion Back (137) to the Seat Frame (115) using the remaining four Seat Cushion Bolts (195) and Washers (196). Do not fully tighten any bolt until all four bolts are started.

R2000

Assembly

Step 4 • Pedals

1: Identify the left and right Pedals (152) and the left and right Pedal Straps(199). Attach the correct straps to each pedal, then thread each Pedal into the correct left and right crank arms and tighten.

The Pedals and Straps are marked with either an L or an R.

NOTE: IT IS VERY IMPORTANT TO FULLY TIGHTEN EACH PEDAL. FAILURE TO DO SO WILL RESULT

IN LOOSENING AND NOISE. USE THE WRENCH PROVIDED OR A 15MM OPEN END WRENCH.

125

130

Step 5 • Console Mast

1: Unfold the RPM Sensor Wire (75) that is folded into the top frame bracket.

Straighten this wire and remove any kinks by drawing the cable through your fingers.

2: Slip the Tension Knob cable (130) along with the RPM Sensor Wire (75) through the Rubber Console Mast Cover (88), then rest the Rubber Console Mast Cover over the top frame bracket.

3: Holding the Console Mast (101) above the top frame bracket, guide the RPM Sensor

Wire (75) through the Console Mast while simultaneously sliding the Console Mast onto the top frame bracket.

4: Slide the Rubber Console Mast Cover (88) up to expose the bolt holes in the Console

Mast (101), then bolt to the frame using six Attachment Bolts (182). Make sure all these bolts are tight. Now slide the Rubber Console Mast Cover (88) back down to cover the bolt heads.

R2000

Final Assembly

Step 6 • Cable Connection

1: Locate the Tension Knob and upper cable assembly (130). Turn the Tension Knob to position 1. Reach inside the opening of the Console Mast (101) and connect the

Upper Magnet Shift Cable (130) to the lower cable hook-slide on the end of the

Lower Magnet Shift Cable (66), as shown in the accompanying illustrations.

2: Insert the cable through the slot and draw the tension cable with the copper end

(130) into the metal bracket notch (131) and insert the cable.

3: Push the cable into the console mast (101). Insert the tension knob assembly to the console mast. Attach bolt (125) through the front of the console mast and tighten down the tension knob assembly.

NOTE: When the tention knob

(130) is inserted into the console mast (101) the Upper

Magnet Shift Cable (130) must be placed in the top of the console mast (101), between the tension knob (130) and the console (153).

130

Step 7 • Console

1: Plug the RPM Sensor Wire (75) into the Console (153). DO NOT PINCH the RPM Sensor Wire between the

Console (153) and the Console Mast (101). Make sure the Sensor Wire fits in the slot cut in the

Console Mast Mount.

2: Mount the Console (153) to the Console Mast (101) using the two Console Attachment Bolts found in the back of the Console.

Step 8 • Install Batteries and Test Operation

1: Remove the battery compartment lid on the back of the Console (153) and install the Batteries. Two AA

Batteries are required.

2: Test ride the bike and make sure that all console feedback functions are operational.

153

75

101

621-D East Lake Street

P.O. Box 280

Lake Mills, WI 53551

(920) 648-4090