Advertisement
Advertisement
1 of 4 Q U ICK STA R T G U I DE 1 Carefully unpack box. 2 Unlock and open front panel of unit for access to internal components. START HERE r IM P O RTA N T! We recommend mounting Ascent T1 on a gooseneck pedestal with the included hardware. If using alternate mounting, the optional Ascent 10' Cable Extension (p/n 16-X-EXT) should be purchased. Follow the instructions included with the extension before moving on. Failure to do so may result in no signal! Continued on next page... What’s what? All the important components labeled for you r Ascent WILL NOT WORK until the activation process is COMPLETE! Antenna Cable SIM Card Follow the Activation Guide or call Summit Control at (844) 259-8265 to activate your unit. Terminal Block If you have your own SIM card, see page 4 and follow the instructions entitled, Installing a Custom SIM Card. IM P O RTA N T! For wiring to gate operator or door opener Camera Mounting Location For future camera kit or third-party camera Speaker Connector Speaker can be disconnected temporarily if unit is intermittently beeping. This is usually due to a SIM card that is not yet activated. Reset Button For performing hard reset Unit shown with front panel fully open. Internal wiring not shown for clarity. C A U TIO N ! WA RN IN G ! AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH! Please use all four screws when mounting unit to a pedestal; leave the “hockey puck” antenna in place, even if using the extension; and seal any holes or gaps created in the enclosure. ALWAYS CHECK that the GATE PATH IS CLEAR BEFORE OPERATING! Failure to follow these instructions can result in damage to the unit! Reversing or other safety devices should ALWAYS BE USED! 2 of 4 QUIC K STAR T GU I DE Connect wires Gate Operator / Door Opener Third-Party 12–24-VAC/DC Power Source LOAD POWER 12–24 VAC/DC N/O COM N/C COM N/O N/C COM N/O NEG. (–) POS. (+) GND N/O POWER 12–24 VAC/DC RELAY A RELAY B EVENT S T OP ! Before proceeding, double check that wiring is correct and unit has power! For additional wiring options, see page 3. © 2016 Security Brands, Inc. 4 Close and lock front panel. CLOSE STOP OPEN COM REVERSE LOOP C A U TIO N ! If you will not be using the supplied 12-VAC transformer, please go to page 4 and follow the procedure, Using a Third-Party Power Source. Do not exceed 24 VAC/DC! Failure to choose a compatible power source can damage unit! Ascent T1 Terminal Block COM Relay B can be wired to a second device in the same manner. STATUS FREE EXIT POS. (+) GROUND NOTE: The GROUND terminal is optional unless required by local code(s).If using, please connect to earth ground or equivalent. COM + – OR RADIO Supplied 12-VAC Transformer COM Feed wires through back of unit and connect as shown. NEG. (–) 3 N INSTALLATION COMPLETE! Now follow the Activation Guide to create an account and begin using Ascent. QSG-16T1-EN Rev. B (9/2016) 3 of 4 QUIC K STAR T GU I DE A Status Check B Event Input Wiring to enable Gate Status Check Wiring for accessories such as a request-to-exit device Gate Operator (If equipped with limit switches) N/C Close Limit Switch N/O COM N/C Open Limit Switch N/O Optional wire splices COM Request-to-Exit (Summit Access Control S-RTE-P is shown) STATUS POWER 12–24 VAC/DC RELAY A RELAY B EVENT Ascent T1 Terminal Block STATUS POWER 12–24 VAC/DC RELAY A RELAY B N/O COM N/C COM N/O N/C COM N/O NEG. (–) POS. (+) GND Connected as shown in Step 3 N/O N/O COM N/C COM N/O N/C COM N/O NEG. (–) POS. (+) GND N/O Connected as shown in Step 3 EVENT Ascent T1 Terminal Block 4 of 4 QUIC K STAR T GU I DE IM P OR T ANT ! r Using a Third-Party Power Source (Optional) If you would like to use a third-party power source, such as solar, verify that it conforms to the following specs: Input Current Draw 1 Installing a Custom SIM Card (Optional) 12–24 VAC/DC no more than 10% under or over less than 90 mA @ 12 VDC less than 60 mA @ 24 VDC Connect wires to unit as shown in 3a Step 3. Slide SIM card holder in OPEN direction and lift to swing open. ? NEED HELP © 2016 Security Brands, Inc. Connect wires to your power source, 3b making sure you connect positive to positive and negative to negative. 2 Remove existing SIM card and install new SIM card. C A U TIO N ! Double check that you’ve wired from positive on Ascent to positive on your power source and negative on Ascent to negative on your power source. Reverse polarity can damage Ascent! 3 Swing cover back down completely and slide in CLOSE direction to lock. Call us at (844) 259-8265 or visit summitcontrol.com/contact We are available Mon–Fri / 8am–5pm Central. QSG-16T1-EN Rev. B (9/2016) ">

Public link updated
The public link to your chat has been updated.
Advertisement