Security Brands 25-S1 Ascent Switch Installation Guide

1 of 2
I n s ta l l G U I D E
1
Model 25-S1
Unpack box and make sure you have all items shown here.
Ascent Unit
Remove screws and open unit cover
for wiring and setup.
2

STOP

This is a cellular accessory for a gate or door.
An uninterrupted cellular connection
CANNOT BE GUARANTEED!
An emergency egress or primary entry
mechanism SHOULD ALWAYS BE USED!
(transmitter, fire box, mechanical release)
Consult with your dealer, distributor, and/or
system designer for more information.
r
12-V AC/DC Adapter
IM P O R TA N T
r
Screwdriver
W A RNI NG


This Ascent unit WILL NOT WORK until the
activation process is COMPLETE!
AUTOMATIC GATES CAN CAUSE SERIOUS
INJURY OR DEATH!
See the included Activation Guide to get this
unit activated.
ALWAYS CHECK THAT THE GATE PATH IS
CLEAR BEFORE OPERATING!
If you need help or have any questions, please
contact Summit Control at (972) 474-6422.
REVERSING OR OTHER SAFETY DEVICES
SHOULD ALWAYS BE USED!
r
IM P O R TA N T
r
If mounting in a location that will shield the
puck antenna, the
4G LTE Antenna Extension Kit
(Model 16-ANTX-1)
should be purchased and installed.
Failure to do so may result in NO SIGNAL!
What’s what?
CA U TI O N


Leave the “hockey puck” antenna in place
even if using an antenna extension.
Seal all openings created in the enclosure.
Failure to follow these instructions can
damage the unit!
Unit shown with cover removed.
Internal wiring not shown for clarity.
All important components labeled
Power Indicator LED
Relay Status LED
Relay is active when lit.
Digital Input Terminals
For connecting accessory
devices. Scan QR code on next
page for wiring instructions.
Cellular Antenna Jacks
Cellular antenna extension kits
connect here.
Smart SIM Card
Press in gently to eject.
Relay Terminals
For wiring to device to be
controlled. See Page 2.
WiFi/Bluetooth Antenna Jack
Power Terminals
For wiring to included power
supply. See Page 2.
Call (972) 474-6422
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
Flip page to continue...
2 of 2
I n s ta l l G U I D E
Connect wires
Consult gate/door opener
manual for exact connections.

Feed wires through one or both
cable glands, and connect as shown
using included screwdriver.
Terminals vary widely across
manufacturers and models.
When connecting the power supply, remember to
connect positive to positive and negative to
negative to avoid damage.
Additional wiring diagrams can
be found online.
N/C
COM
N/O
POS. (+)
NEG. (–)
We recommend using 18-gauge
stranded wire for all connections.
RELAY B
RELAY A
12-V AC/DC Adapter
(included)
The GROUND terminal is
optional unless required by local
code(s). If using, please connect
to earth ground or equivalent.
POWER
12–24 VDC
Ascent Power and Relay Terminals
If plugging into duplex outlet,
remove screw from outlet plate,
and secure with included screw.
(shown with components removed for clarity)

STOP

Before going forward, double check all
wiring and make sure the unit has power!
A wiring diagram for connecting to Wiegand
devices can be found below.
For connecting accessories not mentioned,
please scan the QR code on this page.
Notes
4
Tighten cable gland locknuts, replace
unit cover, and fasten screws.
CA U TI O N

Reversing polarity can damage the unit and
void the warranty!
Some power terminals may be different from that
shown and may be pluggable style.
POWER (+)
POWER (–)
COM
RADIO
FREE EXIT
COM
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
3
Model 25-S1
Gate Operator / Door Opener
N
IN STALLATION COMPLETE!
Now follow the Activation Guide to create an
account and begin using Ascent.
Need More?
Use the QR code below to
get access to more
resources, including how-to
videos and additional wiring
diagrams for connecting
accessory devices.
© 2024 Security Brands, Inc. All rights reserved.
IG-25S1-EN-US
Rev. A (4/2024)
">