1 of 2
I n s ta l l G U I D E
1
Model 25-C2
Unpack box and make sure you have all items shown here.
Ascent Unit
Unlacth and open unit door for wiring
and setup.
2
STOP
This is a cellular accessory for a gate or door.
An uninterrupted cellular connection
CANNOT BE GUARANTEED!
An emergency egress or primary entry
mechanism SHOULD ALWAYS BE USED!
(transmitter, fire box, mechanical release)
Consult with your dealer, distributor, and/or
system designer for more information.
r
12-V AC/DC Adapter
IM P O R TA N T
r
W A RNI NG
This Ascent unit WILL NOT WORK until the
activation process is COMPLETE!
AUTOMATIC GATES CAN CAUSE SERIOUS
INJURY OR DEATH!
See the included Activation Guide to get this
unit activated.
ALWAYS CHECK THAT THE GATE PATH IS
CLEAR BEFORE OPERATING!
If you need help or have any questions, please
contact Summit Control at (972) 474-6422.
REVERSING OR OTHER SAFETY DEVICES
SHOULD ALWAYS BE USED!
r
IM P O R TA N T
r
If mounting in a location that will shield the
puck antenna, the
4G LTE Antenna Extension Kit
(Model 16-ANTX-1)
should be purchased and installed.
Failure to do so may result in NO SIGNAL!
What’s what?
CA U TI O N
Leave the “hockey puck” antenna in place
even if using an antenna extension.
Seal all openings created in the enclosure.
Failure to follow these instructions can
damage the unit!
Unit shown with door fully open.
Internal wiring not shown for clarity.
All important components labeled
Cellular Antenna Jacks
Cellular antenna extension kits
connect here.
Screwdriver
WiFi/Bluetooth Antenna Jack
Power Indicator LED
Digital Input Terminals
For connecting accessory
devices. Scan QR code on next
page for wiring instructions.
Wiegand Terminals
For wiring to Wiegand devices.
See Page 2.
Relay Status LEDs
Relay is active when lit.
Relay Terminals
For wiring to gate operator or
door opener. See Page 2.
Status LEDs are next
Power Terminals
For wiring to included power
supply. See Page 2.
Smart SIM Card
Press in gently to eject.
Call (972) 474-6422
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
Flip page to continue...
2 of 2
I n s ta l l G U I D E
3
Model 25-C2
Connect wires
Consult gate/door opener
manual for exact connections.
Feed wires through one or both
cable glands, and connect as shown
using included screwdriver.
Terminals vary widely across
manufacturers and models.
When connecting the power supply, remember to
connect positive to positive and negative to
negative to avoid damage.
CA U TI O N
Reversing polarity can damage the unit and
void the warranty!
Additional wiring diagrams can
be found below and online.
We recommend using 18-gauge
stranded wire for all connections.
Ascent terminals can be unplugged to make wire
connections easier.
POWER (+)
POWER (–)
COM
RADIO
FREE EXIT
COM
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
NEG. (–)
POS. (+)
N/C
COM
N/O
N/C
COM
N/O
Relay B can be connected in same manner.
12-V AC/DC Adapter
(included)
The GROUND terminal is
optional unless required by local
code(s). If using, please connect
to earth ground or equivalent.
RELAY B
RELAY A
POWER
If plugging into duplex outlet,
remove screw from outlet plate,
and secure with included screw.
12–24 VDC
Ascent Power and Relay Terminals
STOP
Gate Operator / Door Opener
Tighten cable gland locknuts, and then
close and latch door of unit.
4
N
Before going forward, double check all
wiring and make sure the unit has power!
A wiring diagram for connecting to Wiegand
devices can be found below.
IN STALLATION COMPLETE!
For connecting accessories not mentioned,
please scan the QR code on this page.
Now follow the Activation Guide to create an
account and begin using Ascent.
A Wiegand Device
C A U TIO N
Feed wires through one or both cable glands, and
connect as shown using included screwdriver.
Disconnect power to the Ascent unit
before connecting Wiegand devices.
These terminals are used to connect a Wiegand device such
as a card reader or Wiegand keypad.
Failure to disconnect power can
damage the unit!
Either set of Wiegand terminals can be used for wiring and
then configured in Summit Control.
Need More?
Use the QR code below to
get access to more
resources, including how-to
videos and additional wiring
diagrams for connecting
accessory devices.
WIEGAND 1
WIEGAND 2
Ascent Wiegand Terminals
© 2024 Security Brands, Inc. All rights reserved.
+12V
LED 1
LED 2
DATA 1
DATA 0
GND
LED 1
LED 2
+12V
DATA 0
DATA 1
GND
LED 1
LED 2
+12V
DATA 0
DATA 1
GND
Ascent terminals can
be unplugged to
make wire
connections easier.
WIEGAND INPUTS
Wiegand Device
IG-25C2-EN
Rev. 1 (4/2024)
">
