1 of 4
Q U ICK STA R T G U I DE
Model 25-K1
1
Carefully unpack box and make sure you have all items
shown below. (Screwdriver not shown)
What’s what?
Important components labeled
Unit shown with front panel fully open.
Internal wiring not shown for clarity.
Antenna Cables
Ascent Unit
r
12-V AC/DC Adapter
(PS-12DC1)
I M PO R TA NT !
Ascent WILL NOT WORK until the
activation process is COMPLETE!
Follow the Activation Guide or call
Summit Control at (844) 259-8265 to
activate your unit.
Key
Carriage Bolt
( 4x )
Hex Nut
( 4x )
S T OP !
Relay Status LEDs
Relay is active when lit.
This is a cellular accessory for a gate/door,
so an uninterrupted cellular connection
CANNOT BE GUARANTEED.
An emergency egress or primary entry
mechanism SHOULD ALWAYS BE USED
(transmitter, fire box, mechanical release).
Connection Terminals
For wiring to all external devices including
gate operator or door opener
Consult with your dealer, distributor, and/or
system designer for more information.
Power Terminals
W A R NING!
AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
For wiring to compatible AC/DC power source
2
Unlock and open front panel
of unit for wiring and setup.
ALWAYS CHECK that the GATE PATH
IS CLEAR BEFORE OPERATING!
SIM Card
Reversing or other safety devices
SHOULD ALWAYS BE USED!
C A U TIO N !
Please use all four screws when mounting unit to pedestal. Leave “hockey puck” antenna
in place, even if using extension. Seal any holes or gaps created in unit enclosure.
Failure to follow instructions can damage unit!
Continued on next page...
2 of 4
QUIC K STAR T GU I DE
3
Connect wires
Model 25-K1
Ascent Connection Terminals
Feed wires through back of unit
and connect as shown using
included screwdriver.
STATUS
DIGITAL INPUTS EVENT
Gate Operator / Door Opener
RELAY B
RELAY A
J5
J4
12–24 VAC/DC
POWER
Excessive force can damage unit.
J7
12–24 VAC/DC
J8
J9
J6
Before going forward,
double check wiring and
ensure unit has power!
For additional wiring
options, see Page 3.
© 2019 Security Brands, Inc. All rights reserved.
4
Consult gate operator or
door opener manual for
exact connections.
12-V AC/DC Adapter
(Model PS-12DC1 included)
Terminals vary widely
across manufacturers
and models.
The GROUND terminal is optional unless
required by local code(s). If using, please
connect to earth ground or equivalent.
Close and lock front panel.
5
Make sure gate path is clear, then
key in temporary code 2012 on
keypad and confirm gate opens.
2
0
1
2
Adding and deleting codes is done through
Summit Control and NOT from the keypad!
CLOSE
STOP
OPEN
COM
REVERSE LOOP
COM
FREE EXIT
COM
RADIO
COM
NEG. (–)
POS. (+)
N/C
COM
N/O
N/C
N/O
GND
N/O
GND
#2
COM
Relay B can be wired to a second device
in the same manner.
OR
Third-Party 12–24-VAC/DC
Power Source
S T OP !
GND
If plugging into duplex outlet,
remove screw from outlet plate,
and secure with included screw.
+ –
#1
OPEN
NEG. (–)
POS. (+)
J3
CLOSE
Ascent
Power
Terminals
GND
POWER
Additional wiring diagrams
can be found on Page 3.
C A U TIO N !
If you will not be using the 12-V AC/DC adapter,
please go to Page 4 and follow the procedure,
Using a Third-Party Power Source.
Do not exceed 24 VAC/DC! Failure to choose a
compatible power source can damage unit!
N
INSTALLATION COMPLETE!
Now follow the Activation Guide to create
an account and begin using Ascent.
QSG-25K1-EN
Rev. G (5/2019)
3 of 4
QUIC K STAR T GU I DE
N/O
Connected as
shown in Step 3
Optional
wire
splices
Connected as
shown in Step 3
N/C
Close Limit Switch
N/O
COM
N/C
Open Limit Switch
N/O
COM
Gate Operator
N/C
J4
COM
J5
J6
N/O
RELAY A
N/C
RELAY B
COM
J9
GND
J8
N/O
YOU MUST USE A DRY CONTACT!
OPEN
Gate Status Check WILL NOT WORK
with a decoder!
J7
DIGITAL INPUTS EVENT
GND
STATUS
#2
Exceeding 3 V can damage unit!
r I M P OR T AN T!
N/C
N/O
GND
COM
J4
N/O
J5
N/C
RELAY A
COM
RELAY B
J6
N/O
J9
GND
GND
#1
J8
CLOSE
GND
OPEN
J7
DIGITAL INPUTS EVENT
#2
STATUS
Ascent Connection Terminals
#1
Ascent Connection Terminals
Wiring for accessories such as a request-to-exit device
GND
The Status Terminals are designed for
low voltage (3 V or less). Check the
voltage on your status wires before
connecting. If it is above 3 V, you will
need to contact Technical Support.
B Event Input
CLOSE
Wiring to enable Gate Status Check
CAU T I ON !
GND
A Status Check
Model 25-K1
Request-to-Exit
(if equipped with limit switches)
(S-RTE-P is shown)
4 of 4
QUIC K STAR T GU I DE
Model 25-K1
IM P OR T ANT !
r
Using a
Third-Party
Power Source
(Optional)
Connect wires to unit as shown in
If you would like to use a third-party
power source, such as solar, verify that
it conforms to the following specs:
Input
Current Draw
12–24 VAC/DC
no more than 10% beyond this range
less than 260 mA @ 12 VDC
less than 160 mA @ 24 VDC
3a Step 3.
Connect wires to your power source,
3b making sure you connect positive to
C A U TIO N !
Double check that you’ve wired from
positive on Ascent to positive on your
power source and negative on Ascent to
negative on your power source.
Reverse polarity can damage unit!
positive and negative to negative.
r
IM P O RTA N T!
We recommend mounting Ascent on a
gooseneck pedestal using included hardware.
If using alternate mounting, the
4G LTE Antenna Extension Kit
(p/n 16-ANTX-1)
should be purchased and installed.
Failure to do so may result in NO SIGNAL!
? NEED HELP
© 2019 Security Brands, Inc. All rights reserved.
Call (844) 259-8265
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
QSG-25K1-EN
Rev. G (5/2019)
">
