Samsung 765DFX User`s manual

User’s Manual
Index
Main Page
On-Screen Display
General
Highlight Zone
Safety Instructions
Troubleshooting
Natational
Check List
Power
Q&A
Installation
Self-Test Feature Check
Cleaning
Other
Introduction
Specifications
Unpacking
General Specifications
Front
Preset Display Modes
Rear
PowerSaver
Bottom
Setup
Information
Connecting Your Monitor
Service
Installing the Monitor Driver
Terms
— Windows 2000
Regulatory
— Other Operating System
Natural Color
Base Installation
Authority
2
User’s Manual
3
Safety Instructions
Notational
Warning/Caution
Failure to follow directions noted by this symbol could result in bodily harm or damage
to equipment.
Notation Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
User’s Manual
4
Safety Instructions
Power
When not used for extended periods of time, set your PC to DPMS. If using a screen saver,
set it to the active screen mode.
If the size of your monitor is small, or if the same image is present for long periods of time, you
may see afterimages due to damage to the flourescent substance on the inside of the CDT.
•
Do not use a damaged or loose plug.
•
•
Do not pull the plug out by the wire nor touch the plug
with wet hands.
•
•
This may cause an electric shock or fire.
Use only a properly grounded plug and recepticle.
•
•
This may cause an electric shock or fire.
An improper ground may cause electric shock or equipment damage
Do not excessively bend the plug and wire nor place
heavy objects upon them, which could cause damage.
•
Failure to do so may cause an electric shock or fire.
User’s Manual
5
Safety Instructions
Power
•
Disconnect the plug from the outlet during storms or
lightening or if it is not used for a long period of time.
•
•
Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an
outlet.
•
This may cause a fire.
User’s Manual
Safety Instructions
Installation
•
Do not cover the vents on the monitor cabinet.
•
•
Put your monitor in a location with low humidity and a
minimum of dust.
•
•
This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
•
•
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
•
•
Bad ventilation may cause a breakdown or fire.
The monitor can cause injury by falling.
Set down the monitor carefully.
•
It could be damaged or broken.
6
User’s Manual
7
Safety Instructions
Installation
•
Do not place the monitor face down.
•
•
The CDT surface may be damaged.
Do not use the monitor without the monitor stand.
•
•
It could break down or cause a fire due to bad ventilation.
If the monitor must be used without the supplied stand, take steps to
insure proper ventilation.
User’s Manual
8
Safety Instructions
Clean
When cleaning the monitor case or the surface of the CDT, wipe with a slightly
moistened, soft fabric.
Do not clean Flat monitor with water. Use a water-diluted mild detergent.
(Some detergents contain significant amounts of alcohol-based solvents, which
can damage (color change) or crack the monitor case. The antiglare/anti-static
surface coating on the CDT may also be affected.)
Dilute the detergent (1:10 ratio) with water before using.
•
Do not spray detergent directly on the monitor.
•
Use the recommended detergent with a smooth cloth.
•
•
•
If the connector between the plug and the pin is dusty or
dirty, clean it properly with a dry cloth.
•
•
You can prevent the coated CDT from being damaged or the monitor
cabinet from being dissolved, cracked or discolored.
You can buy a recommended detergent at any Samsung Service
Center.
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal
objects on the monitor.
•
•
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug and
then contact a service center.
User’s Manual
9
Safety Instructions
Other
•
Do not remove cover(or back). No user serviceable parts
inside.
•
•
•
If your monitor does not operate normally - in particular,
if there are any unusual sounds or smells coming from
it - unplug it immediately and
contact an authorized dealer or service.
•
•
This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let
your eyes rest for 5 minutes.
•
•
This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor.
•
•
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
This will reduce eye fatigue.
Do not use or store inflammable substances near the
monitor.
•
This may cause an explosion or fire.
User’s Manual
10
Safety Instructions
Other
•
Do not try to move the monitor by pulling on the wire or
the signal cable.
•
•
Do not move the monitor right or left by pulling only the
wire or the signal cable.
•
•
This may cause a breakdown, electric shock or a fire due to damage
to the cable.
Never insert anything metallic into the monitor openings.
•
•
This may cause a breakdown, electric shock or a fire due to damage
to the cable.
This may cause an electric shock, fire or injury.
Keep the monitor away from any magnetic substances.
•
This may cause discoloring or distortion of the image.
User’s Manual
Introduction
Unparking
•
Monitor and Stand
(Some models include a stand attached. )
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
•
Power Cord
•
Stand
•
Quick Setup Guide
•
Warranty Card
(Not available in all locations)
•
User's Guide and
Driver Installation CD
•
USB Hub (Option)
11
User’s Manual
12
Introduction
Front
The Highlight Zone ensures clear images on TVs, video conferencing systems
or photos by emphasizing a certain area on the screen.
Use this button to Exit the active menu or the OSD.
2. Exit button
These buttons allow you to highlight and adjust items in the menu.
3. Adjust buttons
Use this button to open the OSD and activate a highlighted menu item.
4. Menu button
This light glows green during normal operation, and blinks amber once as the
5. Power indicator
monitor saves your adjustments.
Use this button to turn the monitor on and off.
6. Power button
Note:
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.
1. Highlight button
User’s Manual
13
Introduction
Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
2. Signal Cable
Note:
Connect the power cord for your monitor to the power port on the back of the
monitor.
Connect the signal cable to the video port on your computer, video board, video
card, or graphics card.
See Connecting Your Monitor for further information regarding cable connections.
User’s Manual
14
Introduction
Bottom
1. Signal Cable
2. Power Port
3. Tilt/Swivel Base
Connect the signal cable to the video port on your computer, video board, video
card, or graphics card.
Connect the power cord for your monitor to the power port on the back of the
monitor.
You can separate the base from the monitor.
User’s Manual
15
Setup
Connecting Your Monitor
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the video port on your computer, video board, video card, or graphics
card.
3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the
pins on your adapter (Adapter not included). A PC-compatible computer does not need an
adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is
Note:
complete.
Setup
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (Europe)
http://www.samsungmonitor.com/ (USA)
http://www.sec.co.kr/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Windows ME/98/95
1. Insert CD into the CD-ROM driver.
2. Click "Windows ME/98/95 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
Setup
Windows XP/2000
1. Insert CD into the CD-ROM driver.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. If you can see following "Message" window, then click the "Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
6. Monitor driver installation is completed.
Setup
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (Europe)
http://www.samsungmonitor.com/ (USA)
http://www.sec.co.kr/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Microsoft® Windows® XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Setup
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
Setup
This
is
your
Thi monitor
it driver
di
i under
d certifying
tif i MS logo,and
l
d this
thi installation
i t ll ti don't
d 't damage
d
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click "Start" , "Setting" , "Control Panel".
Double click the "Display" Icon.
Choose the "Settings" tab and then click "Advanced..".
Choose "Monitor".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
Choose "Display a list of the known drivers for this device so that I can choose a
specific driver" then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver).
Click the "Open" button, then click "OK" button.
Choose your monitor model and click the "Next" button then click "Next" button.
Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button.
And click the "Finish" button then the "Close" button.
Setup
Microsoft® Windows® Millennium Operating System
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click "Start" , "Setting" , "Control Panel".
Double click "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area.
Choose "Specify the location of the driver".
Choose "Display a list of all the driver in a specific location.." then click "Next" button.
Click the "Have Disk" button
Specify A:\(D:\driver) then click "OK" button.
Select "Show all devices" and choose the monitor that corresponds to the one you
connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties
dialogue box.
(You can get some other screen for warning message or others, then click the appreciate
option for your monitor.)
Microsoft® Windows® 98 Operating System
1.
2.
3.
4.
5.
6.
7.
8.
9.
Click "Start" , "Setting" , "Control Panel".
Double click "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area then click "Next" button.
Choose "Display a list of all the driver.." then click "Next" button.
Click the "Have Disk" button, then click "browse.." button.
Specify A:\(D:\driver) then click "OK" button.
The "Select Device" dialogue box will appear. Select "Show all devices" then choose the
monitor that corresponds to the one you connected to your computer and click OK.
10. Continue choosing "Close" button and "O.K" button until you close the Display Properties
dialogue box.
Microsoft® Windows® 95 Operating System
First determine the Windows 95 version installed on your computer by right-clicking the My
Computer icon on PC and selecting Properties. The version number is listed under System.
Perform the steps for the appropriate version.
Version 4.00.950A
1. Click Start, Settings, Control Panel, and then double-click "Display" icon.
2. In the "Display Properties" window, click the "Settings" tab and click "Change Display
Type".
3. In the "Change Display Type" window, click "Change" and then click "Have Disk".
4. Click "browse.." button and specify A:\(D:\driver) and click "OK".
5. In the Select Device window, click the appropriate monitor model and then click OK.
6. Continue choosing "Close" button and "OK" button until you close the "Display
Properties" dialogue box.
Version 4.00.950B
1. Click Start, Settings, Control Panel, and then double-click "Display" icon.
2. In the "Display Properties" window, click the Settings tab and then click "Advanced
Properties" button.
3. In the "Advanced Display Properties" window, click the "Monitor" tab and then click
"Change" button.
4. In the "Select Device" window, click "Have Disk" button.
5. Click "browse.." button and specify A:\(D:\driver) and click "OK".
6. In the "Select Device" window, click the appropriate monitor model and then click "OK".
Setup
7. C
Continue
choosing
"Close"" b
button
button
the "Di
"Display
7
ti
h
i "Cl
tt and
d "OK" b
tt until
til you close
l
th
l
Properties" dialogue box.
Microsoft® Windows® NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note: If there is no Mode at All Display Modes, select the level of resolution and vertical
frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1.
2.
3.
4.
5.
6.
7.
Press Enter at the first and the second screen after executing the X86Config file.
The third screen is for setting your mouse.
Set a mouse for your computer.
The next screen is for selecting a keyboard.
Set a Keyboard for your computer.
The next screen is for setting your monitor.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency
directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual
execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
User’s Manual
Setup
Base Installation
Tilt/Swivel Base
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.
Note:
The base is detachable.
21
User’s Manual
22
Setup
Base Installation
Attaching and Removing the Bose
1 Attaching the Base
1. Place the monitor upside-down on a flat work
surface.
2. Align the tabs on the base with the corresponding slots
on the bottom of the monitor.
3.Press the base onto the monitor until the tabs are
fully engaged in the slots.
4. Push the base toward the front of the monitor until the
release latch clicks into the locked position.
* Do not bend the snap.
User’s Manual
23
Setup
Base Installation
Attaching and Removing the Bose
2 Removing the Base
5. Squeeze and pull up on the release latch on the
base.
Note:
6. Push the base toward the back of the monitor and lift up
to remove the base.
The base will align with the monitor slots in only one position.
User’s Manual
On-Screen Display
1. Highlight button: The Highlight Zone ensures clear images on TVs,
video conferencing systems or photos by emphasizing a certain area
on the screen.
2. Exit button: Use this button to Exit the active menu or the OSD.
3. Adjust buttons: These buttons allow you to highlight and adjust
items in the menu.
4. Menu button: Use this button to open the OSD and activate a
highlighted menu item.
24
User’s Manual
25
On-Screen Display
Menu
How to adjust
Brightness/Contrast
Adjust Brightness and Contrast.
1
2
Push the ◀▶ ( ◑ ) or ▲ ▼ (
) button. The brightness/contrast display
will appear.
Push the ▲ button to increase the brightness or the ▼ button to decrease
the brightness.
Push the ◀ button to increase the contrast or the ▶ button to decrease the
contrast.
OSD lock/unlock
1
2
Push and hold in the Menu (
) button for 10 seconds or more to Lock
the OSD.
(In this case, even if you click the Menu button(
), the control screen
will not be printed.)
Push and hold in the Menu (
) button for 10 seconds or more to
UnLock the OSD.
User’s Manual
26
On-Screen Display
Menu
How to adjust
Position
Follow these instructions to change the Position of the monitor's entire
display.
1
2
3
Push the Menu(
) button.
Push the Menu(
) button to open the Position adjustment screen.
Use the ▲ and ▼ buttons to change the vertical position of the monitor's
viewing area; use the ◀ and ▶ buttons to change the horizontal position of
the monitor's viewing area.
Size
Follow these instructions to change the size of the monitor's entire
display.
1
2
3
4
Push the Menu(
) button.
Push the ◀ button or ▶ button until the Position/Size screen is displayed.
push the ▲ button or ▼ button to select Size.
Push the Menu(
) button to open the Size adjustment screen.
Use the ▲ and ▼ buttons to change the vertical size of the monitor's
viewing area; use the ◀ and ▶ buttons to change the horizontal size of the
monitor's viewing area.
User’s Manual
27
On-Screen Display
Menu
How to adjust
Zoom
Follow these instructions to get a close-up or a longshot view of the
monitor's viewing area.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Position/Size screen is displayed.
Push the ▲ button or ▼ button to select zoom.
Push the Menu (
) button to open the zoom adjustment screen.
Use the ◀ button to decrease the screen viewing area. Use the ▶ button to
enlarge the screen viewing area.
Parallel/Rotation
Adjust the parallelogram setting when the display is leaning left or right;
adjust the rotation setting when the entire display is tilted left or right.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Geometry screen is displayed.
Push the Menu (
) button to open the Parallel/Rotation adjustment
screen.
Use the ◀ button or ▶ button to adjust the parallel setting;
Use the ▲ button or ▼ button to adjust the rotation setting.
User’s Manual
28
On-Screen Display
Menu
How to adjust
Pincushion/Trapezoid
Adjust the pincushion setting when the sides of the display are bowed
in or bowed out; adjust the trapezoid setting when the top or bottom of
the display is too large or small.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Geometry screen is displayed.
push the▲ button or ▼ button to select Pincushion/Trapezoid.
Push the Menu (
) button to open the Pincushion/Trapezoid
adjustment screen.
Use the ◀ button or ▶ button to adjust the pincushion setting;
Use the ▲ button or ▼ button to adjust the trapezoid setting.
Pinbalance
Adjust the pinbalance setting when the sides of the display are bowed
towards the left or right.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Geometry screen is displayed.
Push the ▲ button or ▼ button to select Pinbalance.
Push the Menu (
) button to open the Pinbalance adjustment screen.
Use the button or button to adjust the Pinbalance setting.
User’s Manual
29
On-Screen Display
Menu
How to adjust
Linearity
Adjust the linearity setting when the display image is compressed at the
left,right or top,bottom.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Geometry screen is displayed.
Push the ▲ button or ▼ button to select Linearity.
Push the Menu (
) button to open the Linearity adjustment screen.
Use the ◀ button or ▶ button to adjust the vertical Linearity.
User’s Manual
30
On-Screen Display
Menu
How to adjust
9300K/6500K
Color temperature is a measure of the "Warmth"of the image colors. The
available range is between 6500 to 9300K.
1
2
3
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Color screen is displayed.
Push the ▲ button or ▼ button to select 9300K (Bluish colors) or 6500K
(Reddish colors).
Clear Moire
A 'moiré' pattern can appear on your screen, looking like a series of
concentric circles or arcs. To eliminate this pattern, use the clear moiré
adjustments.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Screen OSD is displayed.
Push the Menu (
) button to open the Clear Moire adjustment screen.
Use the ◀ button or ▶ button to adjust horizontal moiré;
Use the ▲ button or ▼ button to adjust vertical moiré.
User’s Manual
31
On-Screen Display
Menu
How to adjust
Degauss
The Degauss feature will remove color impurities caused by magnetic
fields. Do not use the Degauss feature more than once within a
30-minute period. Note: The monitor may buzz momentarily, the image
colors may change and the image will jiggle for a few seconds. These
effects are normal.
1
2
3
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Advanced screen is displayed.
Push the Menu (
) button to execute the degauss function. The
degaussing screen will appear. After a few seconds, the degauss main
menu will return.
Recall
Use the recall feature to reset these monitor settings to their original
levels: Position, Size, Pincushion, Trapezoid, Parallelogram,
Pinbalance, Rotation, Clear Moire.
Note: If you have selected "Yes", all settings listed above will be reset.
All other settings will remain the same.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Advanced screen is displayed.
Push the ▲ button or ▼ button to select Recall.
Push the Menu (
) button to open the recall selection screen
Push the ◀ button to select YES. If you don't want to reset the monitor,
use the ▶ button to select NO.
User’s Manual
32
On-Screen Display
Menu
How to adjust
Video Input Level
Some video cards use video signals higher than 1.0V which causes the
display to be very bright. For those video cards, use this feature to
select the 1.0 V Level.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Advanced screen is displayed.
Push the ▲ button or ▼ button to select Video Input Level.
Push the Menu (
) button to open the Video Input Level selection
screen.
Use the ◀ or ▶ buttons to select 0.7 V or 1.0 V.
Display Timing
You can see the frequency (user control mode) used by the user, the
polarity of the operational signals, the default frequency (default mode)
set when you buy the monitor and the resolution level. Note: These
screens do not allow any changes to the settings, they are for
information only.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Menu screen is displayed.
Push the Menu (
) button to open the Display Timing adjustment
screen.
Use the ▼ button to see the user control mode and the default mode.
User’s Manual
33
On-Screen Display
Menu
How to adjust
Menu Duration
The menu will automatically turn off if no adjustments are made for a
certain time period. You can set the amount of time the menu will wait
before it turns off.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Menu screen is displayed.
Push the ▲ button or ▼ button to select Menu Duration.
Push the Menu (
) button to open the Menu Duration selection screen.
Use the ◀▶ or ▲ ▼ buttons to select 3, 7, 10, 20 or 50 seconds. 10
seconds is the default value.
Language
Follow these steps to change the language used in the menu. You can
choose one of ten languages. (English,German,French, Italian,
Portuguese, Spanish, Swedish, Russian, Polish ,or Magyar. Polish and
Magyar may not be available for some products. ) Note:The language
chosen affects only the language of the OSD. It has no effect on any
software running on the computer.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the Menu screen is displayed.
Push the ▲ button or ▼ button to select Languages.
Push the Menu (
) button to open the Languages selection screen.
Use the ▲ button or ▼ button to select the language you would like to
use.
User’s Manual
34
On-Screen Display
Menu
How to adjust
Menu Color
1
2
3
4
Push the (
) button.
Push the ◀ button or ▶ button until the 'Menu' screen is displayed.
Push the ▲ button or ▼ button to select Menu Color.
Push the Menu (
) button to open the Menu Color selection screen.
Use the ▲ button or ▼ button to select Menu Color 1 or Menu Color 2.
Halftone
Use this function to see the transparent on-screen display.
1
2
3
4
Push the Menu (
) button.
Push the ◀ button or ▶ button until the 'Menu' screen is displayed.
Push the ▲ button or ▼ button to select Halfton.
Push the Menu (
) button to open the Halfton selection screen.
Use the ◀ button or ▶ button to select off or on.
User’s Manual
35
On-Screen Display
Menu
How to adjust
Highlight
This function is to execute or cancel the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the Menu (
) button.
Push the ◀ button or ▶ button to cancel, execute or enlarge the entire
screen.
Position
This function is to move the Highlight Zone horizontally or vertically.
1
2
3
Push the Highlight (
) button.
Push the◀button or▶button to select the Screen Position Adjustment and
then push the Menu (
) button.
Push the ◀ button or ▶ button to move the position of the Highlight Zone
horizontally and use the push the ▲ button or ▼ button to move it
vertically.
User’s Manual
36
On-Screen Display
Menu
How to adjust
Size
This function is to adjust the size of the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the ◀ button or ▶ button to select the Screen Size Adjustment and
then push the Menu (
) button.
Push the ◀ button or ▶ button to move the size of the Highlight Zone
horizontally and use the push the ▲ button or ▼ button to move it
vertically.
Contrast
This function is to use the Contrast of the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the ◀ button or ▶ button to select the Contrast Adjustment and then
push the Menu (
) button.
Push the ◀ button or ▶ button to adjust the Contrast of the Highlight
Zone.
User’s Manual
37
On-Screen Display
Menu
How to adjust
Color
This function is to adjust the color of the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the ◀ button or ▶ button to select the Color Adjustment and then
push the Menu (
) button.
Push the ▲ button or ▼ button to select a color from R, G or B.
Push the ◀ button or ▶ button to adjust the R, G or B color of the Highlight
Zone.
Zoom
This function is to enlarge or reduce the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the ◀ button or ▶ button to select theEnlargement and Reduction
Adjustment and then push the Menu (
) button
Push the ◀ button or ▶ button to enlarge or reduce the Highlight Zone.
User’s Manual
38
On-Screen Display
Menu
How to adjust
Sharpness
This function is to adjust the sharpness of the Highlight Zone.
1
2
3
Push the Highlight (
) button.
Push the ◀ button or ▶ button to select the Sharpness Adjustment and
then push the Menu (
) button
Push the ◀ button or ▶ button to adjust the sharpness of the Highlight
Zone.
User’s Manual
39
Troubleshooting
Check List
Before calling for service, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the
warranty card, the phone number on the Information section or contact your dealer.
Symptom
Check List
Solutions
No images on the
screen. I cannot turn on
the monitor.
Is the power cord connected properly?
Check the power cord connection and
supply.
Can you see "No Connection, Check
Signal Cable" on the screen?
Check the signal cable connection.
If the power is on, reboot the computer
to see the initial screen(the login
screen), which can be seen.
If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows 98/95) and then change the
frequency of the video card.
(Refer to the Preset Display Modes)
Note: If the initial screen (the login
screen) does not appear, contact a
service center or your dealer.
Can you see "Sync. Out of Range"
on the screen?
You can see this message when the
signal from the video card exceeds the
maximum resolution and frequency that
the monitor can properly handle.
Adjust the maximum resolution and
frequency that the monitor can properly
handle.
I cannot see the On
Screen Display.
There is no image on the screen. Is
the power indicator on the monitor
blinking at 1 second intervals?
The monitor is in PowerSaver mode.
Have you locked the On Screen
Display (OSD) Menu to prevent
changes?
Unlock the OSD by pressing the MENU
button for at least 10 seconds.
Press a key on the keyboard or move
the mouse to activate the monitor and
restore the image on the screen.
User’s Manual
40
Troubleshooting
Check List
Symptom
The image on the
screen is shaking.
Check List
Solutions
Check the monitor configuration to
see if it is in Interlace Mode. (Interlace
Mode: Vertical frequency 43Hz,
87Hz(i), etc)
The signal from the video card exceeds
the maximum resolution and frequency
of the monitor.
Are there any magnetic products such
as a power adapter, speaker or a high
voltage wire near by?
Move the monitor away from anything
that can create a strong magnetic field.
Is the voltage stable?
The screen image can appear to shake
or vibrate at a particular time of day due
to low supply voltage.
The screen image can also appear to shake or vibrate if there is a problem
with the video card or the computer's main board.
The screen shows
strange colors or just
black and white.
The screen suddenly
has become
unbalanced.
Is the screen displaying only one color
as if looking at the screen through a
cellophane paper?
Check the signal cable connection.
Have the screen colors become
strange after running a program or
due to a crash between applications?
Reboot the computer.
Has the video card been set properly?
Set the video card by referring to the
video card manual.
Have you changed the video card or
the driver?
Adjust screen image position and size
using the OSD.
Have you adjusted the resolution or
frequency to the monitor?
Adjust the resolution and frequency at
the video card.
(Refer to the Preset Display Modes).
Make sure the video card is fully
inserted in it's slot.
The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.
The screen is out of
focus or OSD cannot be
adjusted.
Have you adjusted the resolution or
frequency on the monitor?
Adjust the resolution and frequency of
the video card.
(Refer to the Preset Display Modes).
User’s Manual
Troubleshooting
Check List
Symptom
Check List
Solutions
The screen is partially
distorted.
Are there any magnetic products such
as an adapter, speaker or a high
voltage wire near the monitor?
Enter the OSD and perform a
"Degauss".
Keep the monitor away from any
magnetic products.
LED is blinking but no
images on the screen.
Is the frequency properly adjusted
when checking the Display Timing on
the menu?
Adjust the frequency properly by
referring to the video card manual and
the Preset Display Modes.
(The maximum frequency per
resolution may differ from product to
product.)
There are only 16 colors
shown on the screen.
The screen colors have
changed after changing
the video card.
There is a message that
reads "Unrecognized
monitor, Plug & Play
(VESA DDC) monitor
found".
Have the Windows colors been set
properly?
For Windows 98(95):
Set the colors properly at the Control
Panel, Display, Settings.
For Windows 3.1:
Adjust the colors of the screen using
the VGA utility provided by the video
card.
Has the video card been set properly?
Set the video card by referring to the
video card manual.
Have you installed the monitor driver?
Install the monitor driver according to
the Driver Installation Instructions.
See the video card manual to see if
the Plug & Play (VESA DDC) function
can be supported.
Install the monitor driver according to
the Driver Installation Instructions.
41
User’s Manual
42
Troubleshooting
Check List
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver
and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the
Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to
reinstall the adapter (video) driver.
Tips for Highlight Zone
The Highlight Zone function can be optimized with a moving image and so please use it in the moving
image screen.
1. To protect CDT against the screen brightness, the Highlight Zone function persists for three hours and then
automatically stops. So please reset it to continue.
2. Once the Highlight Zone has been switched off, you can't select any of the other menus within the
Hightlight Zone.
3. When the Highlight Zone function is operated, the surrounding brightness of screen may become dark.
4. Depending on the video card you use, a color saturation phenomenon may occur in the Highlight Zone.
In this case, slightly lower the contrast of the Highlight Zone and the color saturation will be reduced.
5. The Highlight feature is designed for movig image and so please use it in the moving image screen.
If problems repeatedly occur, contact an authorized service center.
Note:
User’s Manual
43
Troubleshooting
Q&A
Question
How can I change the frequency?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the
version of the driver used.
(Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows 95/98: Set the resolution at the Control Panel,
Display, Settings.
Windows 3.1: Change the resolution and the colors using the
VGA Utility provided by the video card.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows 95/98: Set the function at BIOS-SETUP of the
computer or the screen saver. (Refer to Windows/Computer
Manual).
Windows 3.1: Set the function using the VGA
Utility provided by the video card.
The monitor makes a sound when it is
turned on.
This is normal as some sound may be generated when the
metal case and the electromagnet, which are installed to
block any electromagnetic waves, interact with each other.
How can I clean the outer case/Picture
tube?
Disconnect the power cord and then clean the monitor with a
soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the
case. Do not allow any water to go inside the monitor.
Question
Answer
There is no Highlight Zone although I Check to see if the Contrast value of the Highlight Zone is 0
or if you changed the mode without closing the program.
turned the Highlight Zone on.
Check if the Highlight Zone Full Screen function has been
The Position, Size and the Zoom
functions of the Highlight Zone do not used and not released. If it is on, those three functions will
not work.
work.
Note: If this problem keeps happening, reinstall the program.
If you cannot solve this problem, contact the service center.
User’s Manual
44
Troubleshooting
Self-Test Feature Check
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
Self-Test Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
.
3. Turn on the monitor.
If your monitor works normally, the following screen appears.
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during
normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and
computer system; your monitor is functioning properly.
User’s Manual
45
Troubleshooting
Self-Test Feature Check
Werning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen
goes blank although the power indicator LED is still on. The message may indicate that the
monitor is out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the
monitor.
1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another
room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet
(one meter) of the monitor.
3. Degauss the monitor if any devices were removed from the area.
Useful Tips
.
.
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC
or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync. Out
of Range, etc. In this case, first check the source of the problem, and then contact a service center
or your dealer.
Judging the monitor's working condition
If there is no image on the screen or an "Sync. Out of Range" message comes up, disconnect the
cable from the computer while the monitor is still powered on.
. If there is a message coming up on the screen or if the screen goes white, this means the
monitor is in working condition.
. In this case, check the computer for trouble.
Specifications
General
General
Model Name
SyncMaster 955b
Picture Tube
Type
19"(48cm) Full square type (45.8cm viewable)
Deflection angle
90°
Dot Pitch
0.22 mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static
Maximum Resolution
1600 Dots, 1200 Lines @68Hz
Active Display
Horizontal
352 ± 3 mm
Vertical
264 ± 3 mm
Synchronization
Horizontal
30 ~ 85 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Specifications
General
Maximum Pixel Clock
185 MHz
Power Supply
90 ~ 264VAC, 60/50 Hz ± 3Hz
Power Consumption
110W (Max), 100W (Nom)
Dimensions (WxDxH)
440x454x461mm (with Stand)
Weight
19.0 kg
Environmental considerations
Operating
Temperature: 32°F ~ 104°F(0°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will
proceed automatically, unless the user wishes to select alternate settings.
Note:
Design and specifications are subject to change without prior notice.
Specifications
General
General
Model Name
SyncMaster 950b
Picture Tube
Type
19"(48cm) Full square type (45.8cm viewable)
Deflection angle
90°
Dot Pitch
0.22 mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static
Maximum Resolution
1600 Dots, 1200 Lines @68Hz
Active Display
Horizontal
352 ± 3 mm
Vertical
264 ± 3 mm
Synchronization
Horizontal
30 ~ 85 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Specifications
General
Maximum Pixel Clock
185 MHz
Power Supply
90 ~ 264VAC, 60/50 Hz ± 3Hz
Power Consumption
110W (Max), 100W (Nom)
Dimensions (WxDxH)
440x454x461mm (with Stand)
Weight
19.0 kg
Environmental considerations
Operating
Temperature: 32°F ~ 104°F(0°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will
proceed automatically, unless the user wishes to select alternate settings.
Note:
Design and specifications are subject to change without prior notice.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be
adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to
the video card manual and adjust the screen as follows.
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 800 x 600
53.674
85.061
56.250
+/+
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1280 x 1024
79.976
75.025
135.00
+/+
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of the
Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by
switching your monitor into a low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you move the computer's mouse or press a key on
the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card
installed in your computer. Use a software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
Power-off Mode EPA/ENERGY
2000
Green
Green, Blinking
100W(Nominal)
110W(Maximum)
Less than 3W
This monitor is EPA ENERGY STAR ® compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR ® Partner, SAMSUNG has determined that this product
meets the ENERGY STAR ® guidelines for energy efficiency.
Specifications
General
General
Model Name
SyncMaster 955DF
Picture Tube
Type
19"(48cm) DynaFlat (45.8cm viewable)
Deflection angle
90°
Dot Pitch
0.22 mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static
Maximum Resolution
1600 Dots, 1200 Lines @68Hz
Active Display
Horizontal
352 ± 3 mm
Vertical
264 ± 3 mm
Synchronization
Horizontal
30 ~ 85 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Specifications
General
Maximum Pixel Clock
185 MHz
Power Supply
90 ~ 264VAC, 60/50 Hz ± 3Hz
Power Consumption
110W (Max), 100W (Nom)
Dimensions (WxDxH)
440x460x461mm (with Stand)
Weight
21.0 kg
Environmental considerations
Operating
Temperature: 32°F ~ 104°F(0°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will
proceed automatically, unless the user wishes to select alternate settings.
Note:
Design and specifications are subject to change without prior notice.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be
adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to
the video card manual and adjust the screen as follows.
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 800 x 600
53.674
85.061
56.250
+/+
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1280 x 1024
79.976
75.025
135.00
+/+
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of the
Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by
switching your monitor into a low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you move the computer's mouse or press a key on
the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card
installed in your computer. Use a software utility installed on your computer to set up this feature.
State
Power Indicator
Power Consumption
Normal Operation
Power-off Mode EPA/ENERGY
2000
Green
Green, Blinking
100W(Nominal)
110W(Maximum)
Less than 3W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR ® Partner, SAMSUNG has determined that this product
meets the ENERGY STAR ® guidelines for energy efficiency.
Specifications
General
Model Name
SyncMaster 763DFX
Picture Tube
Type
17"(43cm) DynaFlat X (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static
Maximum Resolution
1280 Dots, 1024 Lines @65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
110 MHz
Power Supply
90 ~ 264VAC, 60/50 Hz ± 3Hz
Power Consumption
90W (Maximum), 80W (Nominal)
Dimensions (WxDxH)
398 x 412 x 400mm (with Stand)
Weight
15.9 kg
Environmental considerations
Operating
Temperature: 32°F ~ 104°F(0°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Specifications
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Specifications
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
State
Normal Operation
Power-off Mode EPA/ENERGY
2000
Power Indicator
Green
Green, Blinking
Power Consumption
80W(Nominal)
90W(Maximum)
Less than 3W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product
meets the ENERGY STAR® guidelines for energy efficiency.
Specifications
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 800 x 600
53.674
85.061
56.250
+/+
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of
the screen horizontally is called Horizontal Cycle and the inverse
number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
Model Name
SyncMaster 765DFX
Picture Tube
Type
17"(43cm) DynaFlat X (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static
Maximum Resolution
1600 Dots, 1200 Lines @68Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 85 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
185 MHz
Power Supply
90 ~ 264VAC, 60/50 Hz ± 3Hz
Power Consumption
100W (Maximum), 90W (Nominal)
Dimensions (WxDxH)
398 x 412 x 400mm (with Stand)
Weight
15.9 kg
Environmental considerations
Operating
Temperature: 32°F ~ 104°F(0°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Specifications
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Specifications
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
State
Normal Operation
Power-off Mode EPA/ENERGY
2000
Power Indicator
Green
Green, Blinking
Power Consumption
90W(Nominal)
100W(Maximum)
Less than 3W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product
meets the ENERGY STAR® guidelines for energy efficiency.
Specifications
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 800 x 600
53.674
85.061
56.250
+/+
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1280 x 1024
79.976
75.025
135.00
+/+
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of
the screen horizontally is called Horizontal Cycle and the inverse
number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
User’s Manual
52
Information
Service
● U.S.A.
Samsung Computer Products Customer Service 400 Valley Road,
Suite 201, Mt. Arlington, NJ 07856
Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864)
Fax. : (973)601-6001
http://samsungmonitor.com/
● BRAZIL
Samsung Eletronica da Amazonia Ltda.R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP SAC : 0800 124 421
http://www.samsung.com.br/
● CANADA
Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax. : (905) 542-1199
http://www.samsung.ca
● COLOMBIA
Samsung Electrinics Colombia
Cra 9 No 99A-02 Of. 106 Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 – 2068
http://www.samsung-latin.com/
e-mail : soporte@samsung-latin.com
● PANAMA
Samsung Electronics Latinoamerica( Z.L.) S.A. Calle 50 Edificio Plaza Credicorp,
Planta Baja Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
http://www.samsung-latin.com/
● SOUTH AFRICA
Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext
16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
http://www.samsung.co.za
● UKRAINE
(user manual)
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE
IN UKRAINE 4 Glybochitska str. Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
www.samsung.com.ua (warranty card)
MTI - SAMSUNG SERVICE 9 LEPSE str.KIEV, UKRAINE
TEL. 8-044-4584532
swbills@mti.com.ua
● SWEDEN/DENMARK/NORWAY/FINLAND
Samsung Electronics AB Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
http://www.samsung.se
● PERU
● HUNGARY
● GERMANY
● FRANCE
Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
http://www.samsungperu.com
TELEPLAN Rhein-Main GmbH Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
http://www.samsung.de/
● AUSTRALIA
Samsung Electronics Australia Pty Ltd.
Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
http://www.samsung.com.au/
● ITALY
Samsung Electronics Italia SpA
Via C. Donat Cattin, 5-20063 Cernusco sul Naviglio (Mi)
Tel. : 167-010740
http://www.samsung-italia.com
● ESPAÑA
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
http://samsung.es/
● United Kingdom
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
<European Service Center & National Service>
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
http://samsungservice.co.uk/
● THAILAND
HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING,1st-2nd
Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD ,
SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
Samsung Electronics Magyar Rt. 1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
http://www.samsung.hu
SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2
66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
http://www.samsungservices.com
● PORTUGAL
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, N 2 - 1 Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120
http://www.samsung.pt/
● NETHERLANDS/BELGIUM/LUXEMBOURG
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
● CHILE
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
http://www.sonda.com/
http://www.samsung.cl/
● MEXICO
Samsung Electronics Mexico S.A. de C.V.Saturno 44 Col.
Nueva Industrial Vallejo Del. Gustavo A. Madero C.P. 07700 Mexico D.F.
Tel. 01 57 47 51 00
Fax. 01 57 47 52 02
RFC: SEM950215S98
http://www.samsung.com.mx/
IMPORTADO POR :
SAMSUNG ELECTRONICS MEXICO S.A. DE C.V.
SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO
DEL. GUSTAVO A. MADERO C.P. 07700
MEXICO D.F. TEL. 5747-5100
RFC: SEM950215S98
EXPORTADO POR :
SAMSUNG ELECTRONICS CO.,LTD.
JOONG-ANG DAILY NEWS BLDG.
7 SOON-WHA-DONG CHUNG-KU,
C.P.O BOX 2775, 1144 SEOUL, KOREA
User’s Manual
53
Information
Terms
•
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher
the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
•
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for
the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this case,
flickering of the screen can be detected. To avoid this problem, there is a Flicker-free Mode using a
vertical frequency over 70 Hz.
•
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is
called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.
Unit: kHz
•
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method.
The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace
method is the same as that used in TVs.
•
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the
monitor to exchange information automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
•
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'.
This number shows the accuracy of the display. High resolution is good for performing multiple tasks
as more image information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal
dots (horizontal resolution) and 768 vertical lines (vertical resolution).
•
Highlight Zone
The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by
emphasizing a certain area on the screen.
User’s Manual
54
Information
Regulatory
•
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the following
warning:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television receptions,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
. Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliancecould void the
user's authority to operate the equipment. If necessary, consult your dealeror an experienced radio/television
technician for additional suggestions. You may find thebooklet called How to Identify and Resolve Radio/TV
Interference Problems helpful. This
booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government
Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Declaration of conformity for products Marked with FCC Logo
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
85 West Tasman Drive
San Jose, CA 95134 USA
Tel) 408-544-5124
Fax) 408-544-5191
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be
suitable for connection to any UL Listed personal computer with similar configuration. Before making the
connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and
that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type
(parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with
NEMA configuration 6-15P type (tandem blades) plug cap.
User’s Manual
55
Information
Regulatory
•
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil Numérique de classe Brespecte toutes les exigences du R?glemont ICES-003 sur les
équipements produisant des interférences au Canada.
•
MPR II Compliance
•
European Notice (Europe only)
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
.
.
.
.
.
•
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC)
and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
EN55022:1998 - Radio Frequency Interference
EN55024:1998 - Electromagnetic Immunity
EN61000-3-2:1995+A1+A2 - Power Line Harmonics
EN61000-3-3:1995 - Voltage Fluctuations
EN60950 - Product Safety.
PCT Notice
User’s Manual
56
Information
Regulatory
•
TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to reducing
the burden on the environment and to the further development of environmentally-adapted electronic
products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment.The main problem as far as monitors and other
electronic equipment are concerned is that environmentally harmful substances are used both in the products
and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to
be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from
both the working and natural environment viewpoints. Since all types of conventional electricity generation
have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.)
it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since
it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international environmental
labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The Swedish
Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for Nature
Conservation) and NUTEK (The National Board for Industrial and Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and
magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product
must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must
be adhered to in each country where the company conducts its operations policy. The energy requirements
include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a
lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for the
user. Labelled products must meet strict environmental demands, for example in respect of the reduction of
electric and magnetic fields, along with physical and visual ergonomics and good usability.
User’s Manual
57
Information
Regulatory
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by this product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also be obtained via the Internet,
using the address:
http://www.tco-info.com/
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In
turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame
retardant substances. These are related to another group of environmental toxins, PCBs, which are
suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals, due
to the bioaccumulative processes. Flame retardants have been found in human blood and researchers fear
that disturbances in foetus development may occur. TCO'95 demand requires that plastic components
weighing more than 25 grams must not contain organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. TCO'95 requirement Permits the inclusion of lead since
no replacement has yet been developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. TCO'95 requirement states that
batteries may not contain more than 25 ppm (parts per million) of cadmium. The colour-generating layers of
display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is
toxic in high doses. TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per
million) of mercury. It also demands that no mercury is present in any of the electrical or electronics
components concerned with the display unit.
CFCs (freons)
.
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded
foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere,
causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer
(malignant melanoma).
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the
manufacturing of the product or its packaging.
User’s Manual
58
Information
Regulatory
•
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a
product developed for professional use. Your purchase has also contributed to reducing the burden on the
environment and also to the further development of environmentally adapted electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was developed as
a joint effort by the TCO(The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens Energimyndighet(The
Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric and
magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish Society
for Nature Conservation). These demands impose restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs(freons)and chlorinated solvents, among other things. The
product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which
must be adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
User’s Manual
59
Information
Regulatory
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet,
using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is
to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants
are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive
damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have
been found in human blood and researchers fear that disturbances in foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the
printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement
states that batteries, the colour-generating layers of display screens and the electrical or electronics
components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in
high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light
system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing
this exception when a Mercury free alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture
and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs
break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on
earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion
of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
User’s Manual
60
Information
Natural Color
•
Natural Color Software Program
Die Natural Color S/W ist die Lösung für dieses Problem. Dieses Programm ist ein Farbverwaltungssystem,
daß von Samsung Electronics mit Zusammenarbeit von Korea Electronics & Telecommunications
Forschungsinstitut (ETRI) entwickelt wurde. Dieses System ist nur bei einem Samsung Monitor anwendbar
und ermöglicht, daß die Farbe des Bildes auf dem Monitor den gleichen Effekt zeigt, wie auf dem gedruckten
bzw. gescannten Bild.
Bitte schauen Sie auf die Hilfe (F1) Funktion in dem Software Programm für weitere Informationen.
Installation der Natural Color Software
Legen Sie die CD, die mit dem Samsung Monitor beigefügt ist, in den CD-ROM Treiber ein.
Das Installationsprogramm erscheint automatisch auf dem Bildschirm. Klicken Sie auf das Natural Color,
um das Programm zu installieren.
Wenn Sie das Programm manuell installieren möchten, so legen Sie die CD in den CD-ROM Treiber ein,
drücken Sie auf das [Start] Zeichen des Windows und wählen Sie [Execute].
Geben Sie D:\color\kor\setup.exe ein und dann drücken Sie auf die Eingabetaste.
Wenn der Treiber, wo die CD angetrieben wird nicht D:\ sein sollte, müssen Sie den entsprechenden Treiber
eingeben.
Wie Sie das Natural Color software Programm löschen.
Wählen Sie [Setting]/[Control Panel] auf dem [Start] Menü und dann mit einem Doppelklick auf das [Add/
Delete a program].
Wählen Sie Natural Color aus der Liste aus und dann klicken Sie auf das [Add/Delete] Zeichen.
User’s Manual
61
Information
Authority
Information in this document is subject to change without notice.
ⓒ 2001 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is
strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT
are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of
Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the
U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd.
has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product
names mentioned herein may be the trademarks or registered trademarks of their respective owners.