Elite PRO730HD Operating instructions

XV-HTD340.book 1 ページ 2003年12月27日 土曜日 午前10時30分
DVD/CD Receiver
XV-HTD340
Speaker System
S-HTD340
Register your product at:
www.pioneerelectronics.com
• Protect your new investment
The details of your purchase will be on file for reference in the event of an
insurance claim such as loss or theft.
• Receive free tips, updates and service bulletins on
your new product
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
Operating Instructions
XV-HTD340.book 2 ページ 2003年12月27日 土曜日 午前10時30分
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D1-4-2-3_En
IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND
D1-4-2-6-1_En
KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En
CAUTION
– PREVENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD.
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
ATTENTION – POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER
CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR UNE PRISE DE
COURANT OU UNE AUTRE SORTIE
DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE
D2-4-4-1_EF
A DECOUVVERT.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to lead, a chemical known to
the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
Wash hands after handling
D36-P4_En
For U.S. and Australia Model
WARNING – TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
D1-4-2-1_En
C67-7-3_En
XV-HTD340.book 3 ページ 2003年12月27日 土曜日 午前10時30分
IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
product is operated.
RETAIN INSTRUCTIONS — The safety and
operating instructions should be retained for
future reference.
HEED WARNINGS — All warnings on the product
and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
CLEANING — The product should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides
or other volatile liquids since they may corrode
the cabinet.
ATTACHMENTS — Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
WATER AND MOISTURE — Do not use this
product near water — for example, near a
bathtub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
VENTILATION — Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
POWER SOURCES — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company.
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the
appliance should be unplugged from the outlet
when left un-used for a long period of time.
GROUNDING OR POLARIZATION
• If this product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
• If this product is equipped with a three-wire
grounding type plug, a plug having a third
(grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
POWER-CORD PROTECTION — Power-supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
OUTDOOR ANTENNA GROUNDING — If an
outside antenna or cable system is connected to
the product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode. See Figure A.
LIGHTNING — For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
POWER LINES — An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken
to keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
OBJECT AND LIQUID ENTRY — Never push
objects of any kind into this product through
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the product.
SERVICING — Do not attempt to service this
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
DAMAGE REQUIRING SERVICE — Unplug this
product from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
• When the power-supply cord or plug is
damaged.
• If liquid has been spilled, or objects have fallen
into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
• If the product has been dropped or damaged in
any way.
• When the product exhibits a distinct change in
performance — this indicates a need for service.
REPLACEMENT PARTS — When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK — Upon completion of any service
or repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
WALL OR CEILING MOUNTING — The product
should not be mounted to a wall or ceiling.
HEAT — The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Fig. A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
D1-4-2-2_En
XV-HTD340.book 4 ページ 2003年12月27日 土曜日 午前10時30分
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
D8-10-1-3_EF
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate
the equipment.
D8-10-2_En
CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION : THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.
CAUTION
• Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous
radiation exposure.
• The use of optical instruments with this
product will increase eye hazard.
H013_En
This product is for general household purposes.
Any failure due to use for other than household
purposes (such as long-term use for business
purposes in a restaurant or use in a car or ship)
and which requires repair will be charged for
even during the warranty period.
K041_En
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
D6-8-2-1_En
Energy-saving design
This system is designed to use 0.5W of
electricity when power is switched to
standby.
XV-HTD340.book 5 ページ 2003年12月27日 土曜日 午前10時30分
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future
reference.
Contents
01 Before you start
Remote control . . . . . . . . . . . . . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What’s in the box . . . . . . . . . . . . . . . . . . . . .
Putting the batteries in the remote control . .
Using the remote control . . . . . . . . . . . . . .
Disc / content format playback
compatibility . . . . . . . . . . . . . . . . . . . . . . . .
CD-R/RW compatibility . . . . . . . . . . . . . . .
DVD-R/RW compatibility . . . . . . . . . . . . . .
PC-created disc compatibility . . . . . . . . . .
Compressed audio compatibility . . . . . . . .
About WMA . . . . . . . . . . . . . . . . . . . . . . . .
JPEG file compatibility . . . . . . . . . . . . . . . .
7
7
7
8
8
8
8
9
9
9
9
02 Connecting up
Connecting the speakers . . . . . . . . . . . . . .
Placing the speakers . . . . . . . . . . . . . . . . .
Wall-mounting the surround speaker
system . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to your TV . . . . . . . . . . . . . . . .
Connecting using the S-video output . . . .
Connecting using the component video
output . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to TV audio through this
system . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using this unit with a Pioneer plasma
display . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the SR+ mode with a Pioneer
plasma display . . . . . . . . . . . . . . . . . . . . .
Connecting the supplied antennas . . . . . . .
Assembling the loop antenna . . . . . . . . .
AM loop antenna . . . . . . . . . . . . . . . . . . .
FM wire antenna . . . . . . . . . . . . . . . . . . .
Connecting the power . . . . . . . . . . . . . . . .
10
11
13
13
14
14
16
16
17
18
18
18
19
19
03 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . 20
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
04 Getting started
Switching on and setting up . . . . . . . . . . .
Setting the clock . . . . . . . . . . . . . . . . . . .
Using the Room Setup. . . . . . . . . . . . . . . .
Setting up the remote to control your TV . .
Using the on-screen displays . . . . . . . . . . .
Playing discs . . . . . . . . . . . . . . . . . . . . . . .
Basic playback controls . . . . . . . . . . . . .
Resume and Last Memory . . . . . . . . . . . .
Changing discs . . . . . . . . . . . . . . . . . . . . .
DVD-Video disc menus . . . . . . . . . . . . . .
Video CD PBC menus . . . . . . . . . . . . . . . .
Listening to the radio . . . . . . . . . . . . . . . . .
Improving poor FM reception . . . . . . . . .
Memorizing stations . . . . . . . . . . . . . . . .
Listening to station presets . . . . . . . . . . .
Listening to other sources . . . . . . . . . . . . .
26
27
27
28
29
29
30
31
32
33
34
34
35
35
36
36
05 Listening to your system
About the listening modes. . . . . . . . . . . . .
Auto listening mode . . . . . . . . . . . . . . . . .
Listening in surround sound . . . . . . . . . . .
Dolby Pro Logic II Music settings . . . . . .
Using the Advanced Surround effects . . . .
Using Front Surround . . . . . . . . . . . . . . . .
Adjusting the Advanced and Front
Surround effect level . . . . . . . . . . . . . . . .
Listening in stereo . . . . . . . . . . . . . . . . . . .
Listening with headphones . . . . . . . . . . . .
Enhancing dialogue. . . . . . . . . . . . . . . . . .
Listening with a virtual surround back
speaker . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Quiet and Midnight listening
modes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the bass and treble . . . . . . . . . .
Boosting the bass level . . . . . . . . . . . . . . .
37
37
38
38
39
39
40
40
40
41
41
41
42
42
5
En
XV-HTD340.book 6 ページ 2003年12月27日 土曜日 午前10時30分
06 Playing discs
Playing only CDs and WMA/MP3 discs
(CD mode) . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning discs . . . . . . . . . . . . . . . . . . . . .
Playing in slow motion . . . . . . . . . . . . . . . .
Frame advance/frame reverse . . . . . . . . . .
Using the Disc Navigator to browse the
contents of a disc . . . . . . . . . . . . . . . . . . .
Looping a section of a disc . . . . . . . . . . . .
Using repeat play . . . . . . . . . . . . . . . . . . . .
Using random play . . . . . . . . . . . . . . . . . .
Creating and editing a DVD program list . .
Creating and editing a non-DVD program
list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other functions available from the
program menu . . . . . . . . . . . . . . . . . . . .
Searching a disc . . . . . . . . . . . . . . . . . . . .
Switching subtitles . . . . . . . . . . . . . . . . . .
Switching DVD audio language . . . . . . . . .
Switching audio channels when playing
a Video CD . . . . . . . . . . . . . . . . . . . . . . . . .
Zooming the screen . . . . . . . . . . . . . . . . . .
Switching camera angles . . . . . . . . . . . . .
Displaying disc information . . . . . . . . . . . .
11 Initial Settings menu
43
43
43
44
44
45
45
46
47
48
50
50
51
51
51
51
51
52
07 Viewing JPEG discs
Playing a JPEG slideshow . . . . . . . . . . . . . 53
Using the JPEG Disc Navigator and
Photo Browser . . . . . . . . . . . . . . . . . . . . . . 53
Zooming the screen . . . . . . . . . . . . . . . . . . 54
08 Using the timer
Setting the wake-up timer . . . . . . . . . . . . . 55
Turning the wake-up timer on/off . . . . . . . 56
Setting the sleep timer . . . . . . . . . . . . . . . . 56
09 Surround sound and other
settings
Using the System Setup menu . . . . . . . . .
Surround and sound setup options . . . . .
SR+ control options for Pioneer plasma
displays . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the channel levels . . . . . . . . . . . . .
58
58
59
60
10 Video Adjust menu
Video Adjust . . . . . . . . . . . . . . . . . . . . . . . 62
Creating your own presets . . . . . . . . . . . . 62
6
En
Using the Initial Settings menu . . . . . . . . . . 63
Video Output settings . . . . . . . . . . . . . . . . . 63
Language settings . . . . . . . . . . . . . . . . . . . . 64
Display settings . . . . . . . . . . . . . . . . . . . . . . 64
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Parental Lock . . . . . . . . . . . . . . . . . . . . . . 65
12 Additional information
Optional system settings . . . . . . . . . . . . . . . 67
System Setup menu options in standby . .67
Resetting the system . . . . . . . . . . . . . . . . . . 68
Using and taking care of discs . . . . . . . . . . 68
Titles, chapters and tracks . . . . . . . . . . . . 68
DVD Video regions . . . . . . . . . . . . . . . . . . 68
Handling discs . . . . . . . . . . . . . . . . . . . . . 69
Storing discs. . . . . . . . . . . . . . . . . . . . . . . 69
Discs to avoid . . . . . . . . . . . . . . . . . . . . . . 69
Proper installation and maintenance of
this system . . . . . . . . . . . . . . . . . . . . . . . . . 70
Hints on installation . . . . . . . . . . . . . . . . . 70
Cleaning the pickup lens . . . . . . . . . . . . . 70
Problems with condensation . . . . . . . . . . 70
Moving the system unit. . . . . . . . . . . . . . . 70
Power cord caution. . . . . . . . . . . . . . . . . . 70
Connecting external antennas. . . . . . . . . . . 71
Connecting auxiliary components . . . . . . . . 71
Recording mode . . . . . . . . . . . . . . . . . . . . 72
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 73
General . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
DVD/CD/Video CD player . . . . . . . . . . . . . 74
WMA/MP3/JPEG discs . . . . . . . . . . . . . . . 75
Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Error Messages. . . . . . . . . . . . . . . . . . . . . 76
Screen sizes and disc formats. . . . . . . . . . . 77
Widescreen TV users . . . . . . . . . . . . . . . . 77
Standard TV users. . . . . . . . . . . . . . . . . . . 77
Selecting languages using the language
code list . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Language code list . . . . . . . . . . . . . . . . . . . 78
Country code list . . . . . . . . . . . . . . . . . . . . . 78
Preset code list . . . . . . . . . . . . . . . . . . . . . . 79
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Specifications . . . . . . . . . . . . . . . . . . . . . . . 81
XV-HTD340.book 7 ページ 2003年12月27日 土曜日 午前10時30分
Before you start
01
Chapter 1
Before you start
Features
• 24-bit / 96kHz compatible DAC
This system is fully compatible with high
sampling-rate discs, capable of delivering
exceptional sound quality in terms of dynamic
range, low-level resolution and high-frequency
detail.
• Surround sound entertainment with
Dolby Digital and DTS software
The built-in Dolby Digital and DTS decoders let
you enjoy great surround sound with Dolby
Digital and DTS discs.
• Pure Cinema progressive scan video
When connected to a progressive scancompatible TV or monitor using the
component video outputs, you can enjoy
extremely stable, flicker free images, with the
same frame refresh rate as the original movie.
• Picture zoom
See Zooming the screen on page 51.
• MP3 and WMA compatibility
See Compressed audio compatibility on page 9.
• JPEG compatibility
See JPEG file compatibility on page 9.
• Graphical on-screen displays
Setting up and using your DVD home theater
system is made easy using the graphical onscreen displays.
What’s in the box
Please confirm that the following accessories
are in the main system box when you open it.
• Remote control
• AA/R6P dry cell batteries x2
• Video cable (yellow plugs)
• AM loop antenna
• FM wire antenna
• Power cord
• These operating instructions
• Warranty card
Please confirm that the following accessories
are in the speaker box when you open it.
• Speaker cables x6
• Non-skid pads for speakers (1 sheet)
Putting the batteries in the
remote control
• Open the battery compartment cover
and insert the batteries as shown.
Use two AA/R6P batteries and follow the
indications (, ) inside the compartment.
Close the cover when you’re finished.
• Energy saving design
This system is designed to use 0.5 W of power
when in standby.
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe
the following:
• Don’t mix new and old batteries together.
7
En
XV-HTD340.book 8 ページ 2003年12月27日 土曜日 午前10時30分
01
Before you start
• Don’t use different kinds of battery
together—although they may look similar,
different batteries may have different voltages.
however that some disc types, such as recordable CD and DVD, may be in an unplayable
format—see below for further compatibility
information.
• Make sure that the plus and minus ends of
each battery match the indications in the
battery compartment.
DVD-Video
• Remove batteries from equipment that
isn’t going to be used for a month or more.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Audio CD
DVD-R
Video CD
DVD-RW
CD-R
CD-RW
H048 En
Using the remote control
Keep in mind the following when using the
remote control:
• Make sure that there are no obstacles
between the remote and the remote sensor
on the system unit.
• The remote has a range of about 23 ft. /
7 m at an angle of less than 30º.
• Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the system unit’s remote
sensor.
• Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this system.
• Replace the batteries when you notice a
fall off in the operating range of the remote.
Disc / content format playback
compatibility
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
Fujicolor CD
• KODAK Picture CD
•
is a trademark of Fuji Photo Film Co. Ltd.
CD-R/RW compatibility
• This system will play CD-R and CD-RW
discs recorded in CD Audio or Video CD
format, or as a CD-ROM containing MP3,
WMA or JPEG files. However, any other
content may cause the disc not to play, or
create noise/distortion in the output.
• This system cannot record CD-R or CD-RW
discs.
• Unfinalized CD-R/RW discs recorded as
CD Audio can be played, but the full Table
of Contents (playing time, etc.) will not be
displayed.
DVD-R/RW compatibility
• Compatible formats: DVD-Video, Video
Recording (VR)*
* Edit points may not play exactly as edited;
screen may go momentarily blank at edited
points.
• Unfinalized playback: No
8
En
XV-HTD340.book 9 ページ 2003年12月27日 土曜日 午前10時30分
Before you start
• WMA/MP3/JPEG file playback on DVD-R/
RW: No
01
About WMA
PC-created disc compatibility
Discs recorded using a personal computer
may not be playable in this unit due to the
setting of the application software used to
create the disc. In these particular instances,
check with the software publisher for more
detailed information.
Discs recorded in packet write mode (UDF
format) are not compatible with this player.
Check the DVD-R/RW or CD-R/RW software
disc boxes for additional compatibility
information.
Compressed audio compatibility
• Compatible formats: MPEG-1 Audio Layer 3
(MP3), Windows Media Audio (WMA)
• Sampling rates: 32, 44.1 or 48kHz
• Bit-rates: Any (128Kbps or higher recommended)
• VBR (variable bit rate) MP3 playback: Yes
• VBR WMA playback: No
• WMA lossless encoding compatible: No
• DRM (Digital Rights Management)
compatible: Yes (DRM-protected audio
files will not play in this player). See also
DRM in the Glossary on page 80.
• File extensions: .mp3, .wma (these must be
used for the player to recognize MP3 and
WMA files – do not use for other file types)
The Windows Media® logo printed on the box
indicates that this player can playback
Windows Media Audio content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media® Player version 7, 7.1, Windows Media®
Player for Windows® XP, or Windows Media®
Player 9 Series.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
JPEG file compatibility
• Compatible formats: Baseline JPEG and
EXIF 2.1* still image files up to 8 megapixels are supported (maximum resolution
is 5120 x 5120 pixels).
*File format used by digital still cameras
• File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use
for other file types)
• File structure: Up to 999 files per folder
• File structure: Up to 999 files per folder
9
En
XV-HTD340.book 10 ページ 2003年12月27日 土曜日 午前10時30分
02
Connecting up
Chapter 2
Connecting up
Connecting the speakers
• Before making or changing any rear panel connections, make sure that all the components
are switched off and unplugged from the power supply.
Surround right
XV-HTD340
VIDEO
OUT
Surround left
IN
CONTROL
Y
S-VIDEO
OUT
VIDEO
SPEAKERS
FRONT
R
L
SUB
WOOFER
SURROUND
CENTER
R
L
AUDIO
Gray
OUT
COAXIAL IN
L
LINE 2
IN
Blue
R
LINE 1
Subwoofer
Green
Front right
Front left
Center
Purple
Red
White
Connect each speaker using the color-coded speaker cable. Match them to the colored labels
above the speaker terminals.
10
En
XV-HTD340.book 11 ページ 2003年12月27日 土曜日 午前10時30分
Connecting up
02
3 Connect to the speaker terminals on the
rear of the speakers in the same way.
• These speaker terminals can be under
HAZARDOUS VOLTAGE. When you
connect or disconnect the speaker cables,
to prevent the risk of electric shock, do not
touch uninsulated parts before
disconnecting the power cord.
• Do not connect any of the supplied
speakers to any other amplifier. This may
result in malfunction or fire.
This system has been designed for best
performance when connected to the
supplied speakers. We do not, therefore,
recommend that you connect and use
other speakers with this system.
1 Twist and pull off the protective shields
on each wire.
2 Connect to the speaker terminals on the
rear of the system unit.
Match the colored wire with the color-coded
label (above the tabs), then insert the colored
wire into the red (+) tab and the other wire with
the black (–) tab.
• Remove the supplied non-skid pads from
the paper, and stick four onto the base of
each satellite speaker. Actual speakers
supplied may differ from those shown.
Placing the speakers
Depending on the size and characteristics of
your room, you can choose to place your
speakers in one of two ways using this system:
• Standard surround 5-spot setup – This is
a standard multichannel surround sound
speaker setup for optimal 5.1 channel
home theatre sound.
Front left
System
unit
Subwoofer
Front right
Center
Surround
left
Surround
right
11
En
XV-HTD340.book 12 ページ 2003年12月27日 土曜日 午前10時30分
02
Connecting up
Front left
Center
Front right
Where you put your speakers in the room has a
big effect on the quality of the sound. The
following guidelines should help you to get the
best sound from your system.
Subwoofer
Listening position
Surround
right
Surround
left
• Front surround 3-spot setup – This setup
is ideal when rear surround speaker
placement isn’t possible or you want to
avoid running long speaker cables in your
listening area. Use this setup together with
the Front Surround modes to take
advantage of wall and ceiling reflections
for a very realistic surround effect.
Surround
left
System
unit
Front
left
Surround
right
Subwoofer
See About the listening modes on page 37 for
more on using the different listening modes
with each speaker setup.
Front
right
• The subwoofer can be placed on the floor.
Ideally, the other speakers should be at
about ear-level when you’re listening to
them. Putting the speakers on the floor
(except the subwoofer), or mounting them
very high on a wall is not recommended.
• For the best stereo effect, place the front
speakers 6–9 ft. / 2–3 m apart, at equal
distance from the TV.
• Install the center speaker above or below
the TV so that the sound of the center
channel is localized at the TV screen.
• When using a 5-spot setup, install the
surround speakers slightly above ear level,
if possible.
Center
Center
Front
left
Front
right
Subwoofer
Surround
left
Surround
right
Listening position
12
En
• Make sure that all speakers are securely
installed (if you choose to install the center
speaker on top of the TV, be sure to secure
it by suitable means). This not only
improves sound quality, but also reduces
the risk of damage or injury resulting from
speakers being knocked over or falling in
the event of external shocks such as
earthquakes.
XV-HTD340.book 13 ページ 2003年12月27日 土曜日 午前10時30分
Connecting up
02
• The front, center and surround speakers
supplied with this system are magnetically
shielded. However, placing them extremely
close to a television may result in color
distortion on the screen. If this happens,
move the speakers a little further away and
switch off the television for 15–30 minutes.
• The subwoofer is not magnetically shielded
and so should not be placed near a TV or
monitor.
Wall-mounting the surround speaker
system
• If you are unsure of the qualities and
strength of the walls, consult a
professional for advice.
• Pioneer is not responsible for any
accidents or damage that result from
improper installation.
Connecting to your TV
This system has three different kinds of video
output that you can use to connect up your TV.
Check the available inputs on your TV to see
which you can use.
Before mounting
• Remember that the speaker system is
heavy and that its weight could cause the
wood screws to work loose, or the wall
material to fail to support it, resulting in the
speaker falling. Make sure that the wall you
intend to mount the speakers on is strong
enough to support them. Do not mount on
plywood or soft surface walls.
• Do not connect a VCR between this system
and your TV as DVD playback will be
affected.
• Use the supplied video cable to connect
the VIDEO OUT jack to a video input on
your TV.
• Mounting screws are not supplied. Use
screws that are suitable for the wall
material and that will support the weight of
the speaker.
VIDEO
INPUT
TV
3–5 mm
10 mm
Wood screw
PR
VIDEO
OUT
PB
IN
CONTROL
COMPONENT
VIDEO OUT
Y
S-VIDEO
OUT
VIDEO
Protrusion: 5-7mm
SPEAKERS
FRONT
R
L
SUB
WOOFER
CENTER
13
En
XV-HTD340.book 14 ページ 2003年12月27日 土曜日 午前10時30分
02
Connecting up
Connecting using the component
video output
• Placing the system unit too close to your TV
may cause interference, especially if you’re
using an indoor antenna. If you notice
interference, move the system unit away
from the TV.
Connecting using the S-video output
If your TV has an S-video input, you can use this
instead of the standard video output for a
better quality picture.
If your TV has component video inputs, you can
use these instead of the standard video output
to connect this system to your TV. This should
give you the best quality picture from the three
types of video output available.
• Use a component video cable (not
supplied) to connect the COMPONENT
VIDEO OUT to a set of component inputs
on your TV.
• Use an S-video cable (not supplied) to
connect the S-VIDEO OUT to an S-video
input on your TV.
Line up the small triangle below the jack with
the same mark on the plug before plugging in.
COMPONENT
INPUT
TV
S-VIDEO
INPUT
TV
PR
VIDEO
OUT
PB
IN
CONTROL
COMPONENT
VIDEO OUT
Y
S-VIDEO
OUT
VIDEO
SPEAKERS
PR
VIDEO
OUT
PB
FRONT
R
IN
L
SUB
WOOFER
CONTROL
COMPONENT
VIDEO OUT
Y
S-VIDEO
OUT
VIDEO
SPEAKERS
FRONT
R
L
SUB
WOOFER
CENTER
• The S-video output is switchable between
S1 and S2 formats for compatibility with all
TVs. See Video Output settings on page 63
for more on this.
14
En
• The component video output is switchable
between interlaced and progressive
formats. See Video Output settings on
page 63 and Watching progressive scan
video from the component video outputs
below for more on this.
02_Connecting_Up.fm 15 ページ 2003年12月27日 土曜日 午前11時52分
Connecting up
Watching progressive scan video from
the component video outputs
Compared to interlace video, progressive scan
video effectively doubles the scanning rate of
the picture, resulting in a very stable, flickerfree image. Progressive scan video is available
only from the component video output. There
are a few things to keep in mind when
switching the Component Out (page 63)
setting to Progressive:
• When set to Progressive, there is no video
output from the VIDEO OUT (composite)
and S (S-video) jacks.
• If you want to display video on more than
one monitor simultaneously, make sure
the player is set to Interlace.
• If you connect a TV that is not compatible
with a progressive scan signal and switch
the setting to Progressive, you will not be
able to see any picture at all. In this case,
press STANDBY/ON to put the system
in standby, then press and hold the front
panel (stop) button for about 8 seconds
until the display shows Mem.Clr.?. Press
the front panel or button
so that the display shows Interlace?. Press
the front panel button to set to
interlace and switch the system back on.
02
connection to the ‘standard definition’ output
(Interlace). If there are questions regarding our
TV set compatibility with this model, please
contact our customer service center.
This system is compatible with the following
Pioneer displays and monitors:
Plasma display
PDP-505HD, PDP-5030HD, PDP-4330HD,
PDP-5040HD, PDP-4340HD, PRO-10000HD,
PRO-800HD, PRO-1000HDI, PRO-800HDI,
PRO-1110HD, PRO-910HD, PDP-4300, PDP5031
Projection monitor receiver
SD-533HD5, SD-643HD5, PRO-710HD, PRO610HD, PRO-510HD, PRO-720HD, PRO620HD, PRO-520HD, PRO-730HD, PRO630HD, PRO-530HD, PRO-730HDI, PRO530HDI
Compatibility of this player with
progressive-scan and high-definition
TVs.
This player is compatible with progressive
video Macro Vision System Copy Guard.
Consumers should note that not all highdefinition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525
progressive scan picture problems, it is
recommended that the user switch the
15
En
02_Connecting_Up.fm 16 ページ 2003年12月27日 土曜日 午前11時52分
02
Connecting up
Listening to TV audio through this
system
You can connect the audio output of your TV to
this system so that broadcast TV sound is
played through this system.
• Connect a stereo audio cable (not
supplied) from the audio outputs of your
TV to the TV IN jacks on this system.
Using this unit with a Pioneer
plasma display
If you have a Pioneer plasma display (models
PRO-1110HD, PRO-910HD, PDP-5040HD,
PDP-4340HD), you can use an SR+ cable (see
note below) to connect it to this unit and take
advantage of various convenient features,
such as automatic video input switching of the
plasma display when the input is changed.
AUDIO
OUTPUT
TV
Pioneer plasma display
CONTROL
Media receiver
OUT
PR
VIDEO
OUT
ANTENNA
AUDIO
OUT
IN
PB
IN
CONTROL
COMPONENT
VIDEO OUT
Y
S-VIDEO
OUT
VIDEO
AM LOOP
ANTENNA
IN
COAXIAL IN
LINE 2
L
L
R
R
LINE 1
FM
UNBAL
75
TV
• If you find that the TV audio is distorting
when played through this system, you can
set the input attenuator to reduce the input
signal level. See Optional system settings
on page 67 to do this.
16
En
SPEAKERS
• Use a 3-ringed miniplug SR+ cable to
connect the CONTROL IN jack of this unit
through a media receiver to the CONTROL
OUT jack of your plasma display.
Before you can use the extra SR+ features, you
need to make a few settings in the unit. See
SR+ control options for Pioneer plasma displays
on page 59 for detailed instructions.
XV-HTD340.book 17 ページ 2003年12月27日 土曜日 午前10時30分
Connecting up
Using the SR+ mode with a Pioneer
plasma display
When connected using an SR+ cable, a
number of features (such as automatic video
input switching and volume muting on the
plasma display) become available to make
using this unit with your Pioneer plasma
display even easier.
See also SR+ control options for Pioneer
plasma displays on page 59 for information on
setting up the unit.
1 Make sure that the plasma display and
this unit are switched on and that they are
connected with an SR+ cable.
See Using this unit with a Pioneer plasma
display above for more on connecting these
components.
02
• The automatic volume muting feature is
enabled separately; see SR+ control
options for Pioneer plasma displays on
page 59. (You can also use the System
Setup menu to switch the SR+ mode of
this unit.)
• If you disconnect the SR+ cable or switch
the plasma display off while SR+ is on, the
setting automatically reverts to SR+ OFF.
This displays an error if you switch the
input of the unit with the plasma display
switched off. Likewise, if this unit is
switched off, the link with the plasma
display will be terminated.
2 To switch SR+ mode on/off, press SR+
(SHIFT + 7).
The front panel display shows the new setting;
SR+ ON or SR+ OFF.
• If SR+ Error shows in the display, it means
there is a communication problem
between the unit and the plasma display.
Check all connections and retry.
• The 3-ringed SR+ cable from Pioneer is
commercially available under the part
number ADE7095. Contact the Pioneer
Customer Support division for more
information on obtaining an SR+ cable.
• You won’t be able to use the remote sensor
of this unit with the CONTROL IN jack of
this unit connected to the CONTROL OUT
jack of your plasma display. You can use
the remote sensor of the plasma display
(even in standby) as long as the power isn’t
switched off.
17
En
XV-HTD340.book 18 ページ 2003年12月27日 土曜日 午前10時30分
02
Connecting up
Connecting the supplied antennas
The supplied antennas provide a simple way to listen to AM and FM radio. If you find that reception
quality is poor, an outdoor antenna should give you better sound quality—see Connecting external
antennas on page 71 for more on how to do this.
FM wire (PAL)
antenna
AM loop antenna
AC IN
ANTENNA
AUDIO
OUT
IN
AM LOOP
ANTENNA
IN
COAXIAL IN
LINE 2
L
L
R
R
LINE 1
FM
UNBAL
75
TV
Assembling the loop antenna
AM loop antenna
1 Bend the stand in the direction
indicated.
1 Pull off the protective shields of both
AM antenna wires.
2 Press the antenna terminal tabs to open
and insert one wire into each terminal.
3 Release the tabs to secure the AM
antenna wires.
2
18
En
Clip the loop onto the stand.
4 Place the AM antenna on a flat surface
and point in the direction giving the best
reception.
Avoid placing near computers, television sets
or other electrical appliances and do not let it
come into contact with metal objects.
XV-HTD340.book 19 ページ 2003年12月27日 土曜日 午前10時30分
Connecting up
02
Connecting the power
• It’s also possible to fix the AM antenna to a
wall using two screws (see illustration
below). Before fixing, make sure that the
reception is satisfactory.
Before connecting the power and switching on
for the first time make sure that everything is
connected properly.
AC IN
ANTENNA
FM wire antenna
• Connect the FM wire antenna to the FM
UNBAL 75Ω terminal in the same way as
the AM loop antenna.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Don’t drape
loosely or leave coiled up.
AM LOOP
ANTENNA
FM
UNBAL
75
Power outlet
1 Plug one end of the supplied power
cord into the AC INLET.
• The signal ground (
) is designed to
reduce noise that occurs when an antenna
is connected. It is not an electrical safety
ground.
2 Plug the other end into a household
power outlet.
• See Connecting auxiliary components on
page 71 for details of other connections
you can make with this system.
19
En
XV-HTD340.book 20 ページ 2003年12月27日 土曜日 午前10時30分
03
Controls and displays
Chapter 3
Controls and displays
Front panel
1
2
3
5
6
7
8
9
10
11
EXCHANGE
OPEN/CLOSE
FM/AM/ST.
DIRECT PLAY
1
4
2
3
4
5
DVD/CD
TUNER
TV/L1/L2
DISC SKIP
STANDBY/ON
PHONES
VOLUME
DISC
1
2
3
4
5
CD MODE TIMER
DOWN
19
18
17
16 15 14
1 STANDBY/ON (page 26)
Press to switch the system on or into standby.
2 DIRECT PLAY buttons (page 30)
Press to start playback of any disc in the
player.
3 DVD/CD (page 29)
Press to switch to the DVD/CD function. Also
starts/pauses/resumes playback of the
currently loaded disc.
4 TUNER FM/AM/ST. (page 34)
Press to switch to the tuner function, then
between bands and station presets.
5 TV/L1/L2 (page 36)
Press to switch between the external sources,
TV, LINE 1 (L1) and LINE 2 (L2).
6 and Press to skip tracks/chapters; press and hold
to scan backwards/forwards.
20
En
UP
13
12
• When in listening to the tuner, use to tune
to stations or select presets.
7 Press to stop playback.
8 Press to start or resume playback. During
playback, press to pause; press again to
restart playback.
9
DISC SKIP (page 30, 32)
• During playback, press to start playing the
next disc in the player.
• If the disc tray is open while no disc is
playing, the tray rotates one disc space.
• If the disc tray was opened using the
EXCHANGE button, then pressing DISC
SKIP rotates the disc tray two disc spaces.
XV-HTD340.book 21 ページ 2003年12月27日 土曜日 午前10時30分
Controls and displays
03
10 EXCHANGE (page 32)
Press during playback to open the disc tray
without stopping playback. Press again to
close the disc tray.
16 CD MODE indicator (page 43)
Lights when the CD Mode is on. In this mode,
the system only plays audio CDs and WMA/
MP3 discs.
11 OPEN/CLOSE
Press to open/close the disc tray.
17 Display
See Display on page 21 for detailed
information.
12 Disc tray
18 DISC indicators
Shows which disc spaces are currently
occupied.
13 VOLUME control
Use to adjust the volume.
14 Timer indicator (page 55)
Lights when the timer is set.
19 PHONES jack
Headphone jack.
15
This mark indicates compatibility with DVDRW discs recorded on a DVD recorder in
Video Recording (VR) mode.
Display
1 2
3
4
5
MIDNIGHT QUIET
6
7
8
9
PGM
RPT -1
RDM
ATT
10 11
REC MODE
kHz
MHz
20
1
19
12
13
14
PRO LOGIC
DIGITAL
ADV.SURR.
Neo:6
PRGSVE
18 17 16 15
Tuner indicators (page 34)
Lights when a broadcast is being
received.
Lights when a stereo FM broadcast is
being received in auto stereo mode.
Lights when FM mono reception is
selected.
2 Lights when a disc is playing.
3 MIDNIGHT (page 41)
Lights when the Midnight mode is selected.
4 QUIET (page 41)
Lights when the Quiet mode is selected.
21
En
XV-HTD340.book 22 ページ 2003年12月27日 土曜日 午前10時30分
03
Controls and displays
5
Lights to indicate random or repeat play of all
discs loaded.
3.1 channel sound with Dialogue
enhancement on the center
channel
6 PGM (page 47)
Lights when a program list has been
programmed.
5.1 channel surround sound with
Virtual Surround Back mode active
7 RPT and RPT-1 (page 45)
RPT lights during repeat play. RPT-1 lights
during repeat one-track play.
(When headphones are connected, none of
the speaker indicators are lit.)
8 RDM (page 46)
Lights during random play.
15 PRGSVE (page 63)
Lights when progressive scan video output is
selected.
9 ATT (page 67)
Lights when the input attenuator is active for
the currently selected analog input.
10 REC MODE (page 72)
Lights when Rec Mode is on.
11 Timer indicators (page 55)
18 kHz / MHz
Indicates the unit of the frequency shown in
the character display (kHz for AM, MHz for
FM)
Lights when the sleep timer is active
19 Character display
13 2 DIGITAL (page 38)
Lights during playback of a Dolby Digital
source.
14 Speaker indicators
These show which speakers are being used to
output the current source (they are not
placement diagrams). The illustrations below
show some example displays.
5.1 channel surround sound
Stereo (2.1 channel) sound
22
17
(page 38)
Lights during playback of a DTS source.
Lights when the timer is set
12 2 PRO LOGIC II (page 38)
Lights during Dolby Pro Logic II decoding.
En
16 ADV.SURR. (page 39)
Lights when one of the Advanced or Front
Surround listening modes is selected.
(page 51)
20
Lights during multi-angle scenes on a DVD
disc.
XV-HTD340.book 23 ページ 2003年12月27日 土曜日 午前10時30分
Controls and displays
03
2 OPEN/CLOSE
Press to open/close the disc tray.
Remote control
STANDBY/ON
OPEN/CLOSE
1
2
FM/AM
3
DVD/CD
4
SOUND
MODE
6
8
L1/L2
TUNER
TV
LINE
DIALOGUE
VIR. SB
BASS MODE
SURROUND ADVANCED
AUDIO SUBTITLE ANGLE
FRONT
SURROUND
ZOOM
DISC 1
DISC 2
DISC 3
CD MODE
ROOM
SETUP
DISC 4
DISC 5
DISC SKIP
MUTE
10
7
9
4 SOUND MODE
Use to adjust the tone and effect levels/
settings. (pages 38–42)
5 Surround sound and enhancement
buttons
SURROUND (page 38)
Use to select a Surround mode.
VOLUME
TOP MENU
SYSTEM SETUP
11
13
DIALOGUE (SHIFT + SURROUND)
(page 41)
Use to select a Dialogue mode.
12
TUNE +
HOME
MENU
DVD MENU
ST –
ENTER
ST +
QUIET/
MIDNIGHT
RETURN
TUNE –
14
16
5
3 Function select buttons
Press to select the source you want to listen to
(DVD/CD, TUNER, TV, LINE).
FOLDER
ADVANCED (page 39)
Use to select an Advanced Surround
mode.
15
FOLDER
VIR. SB (SHIFT + ADVANCED) (page 41)
Press to switch the Virtual Surround Back
speaker effect on/off.
PROGRAM REPEAT RANDOM
CLEAR
TEST TONE CH LEVEL
TIMER
17
FRONT SURROUND (page 39)
Use to select a Front Surround listening
mode.
ENTER
SR +
DISPLAY
SHIFT
INPUT
DIMMER
TV CONTROL
19
CHANNEL VOLUME
18
BASS MODE (SHIFT + FRONT
SURROUND) (page 42)
Use to select a Bass Mode.
5.1ch DVD SURROUND SYSTEM
6
DVD buttons
AUDIO (page 51)
Press to select an audio channel or
language.
• Functions printed in green on the remote
control are accessed using the SHIFT
button. Press the function button you want
while holding down SHIFT.
1 STANDBY/ON (page 26)
Press to switch the system on or into standby.
SUBTITLE (page 51)
Press to display/change the subtitle
display.
ANGLE (page 51)
Press to change camera angle during DVD
multi-angle scene playback.
23
En
XV-HTD340.book 24 ページ 2003年12月27日 土曜日 午前10時30分
03
Controls and displays
ZOOM (page 51)
Press to change the screen zoom level.
7
ROOM SETUP (page 27)
Press to start Room Setup.
8
Disc selection buttons
DISC select buttons (page 29)
Use to select discs in the player.
ENTER
Press to select an option or execute a
command.
TUNE +/–
Use to tune the radio.
• If the disc tray is open while no disc is
playing, the tray rotates one disc space.
ST +/–
Use to select station presets when
listening to the radio.
• If the disc tray was opened using the
EXCHANGE button (front panel only), then
pressing DISC SKIP rotates the disc tray
two disc spaces. (page 30, 32)
14 QUIET/MIDNIGHT (page 41)
Use to select Quiet and Midnight listening
modes.
• Use with SHIFT for CD MODE: Use to
switch CD Mode on/off. (page 43)
15 RETURN
Press to return to a previous menu screen.
10 VOLUME
Use to adjust the volume.
11 HOME MENU / SYSTEM SETUP
• Press to display (or exit) the on-screen
menu for Initial Settings, Play Mode
functions, etc.
• Use with SHIFT for SYSTEM SETUP: Use to
make various system and surround sound
settings. (page 58)
12 DVD MENU / TOP MENU
• Press to display a DVD-Video disc menu, or
the Disc Navigator if a VR mode DVD-RW,
CD, Video CD, WMA/MP3 or JPEG disc is
loaded.
• Use with SHIFT for TOP MENU: Use to
display the top menu of a DVD disc in the
play position (this may be the same as
pressing DVD MENU).
24
Cursor buttons
Use the cursor buttons (///) to
navigate on-screen displays and menus.
DISC SKIP / CD MODE
• During playback, press to start playing the
next disc in the player.
9 MUTE
Press to mute all sound from the speakers and
headphones (press again to cancel).
En
13 Cursor buttons, ENTER and tuning
buttons
16 Playback controls
Press to start or resume playback.
and /
Use for reverse slow motion playback,
frame reverse and reverse scanning.
and /
Use for forward slow motion playback,
frame advance and forward scanning.
/ FOLDER –
Press to jump to the beginning of the
current chapter/track, then to previous
chapters/tracks.
Press SHIFT + to jump to the
beginning of the previous folder
/ FOLDER +
Press to jump to the next chapter/track (or
folder by pressing SHIFT + ).
XV-HTD340.book 25 ページ 2003年12月27日 土曜日 午前10時30分
Controls and displays
Press to pause playback; press again to
restart.
Press to stop playback.
17 Number buttons and SHIFT functions
Use the number buttons for selecting
chapters/tracks from a disc directly; use with
the SHIFT button to access the functions
printed in green.
PROGRAM (SHIFT + 1) (page 47)
Use to program/play a program list.
REPEAT (SHIFT + 2) (page 45)
Use to select a repeat play mode.
RANDOM (SHIFT + 3) (page 46)
Use to select a random play mode.
03
18 TV CONTROL buttons
These buttons are dedicated to control the TV
assigned to the TV button.
Use to turn on/off the power of the TV.
INPUT
Use to select the TV function.
TV CHANNEL +/–
Use to select channels.
TV VOLUME +/–
Use to adjust the volume on your TV.
19 SHIFT
Use to access the functions/commands
printed in green on the remote (press the
button for the function you want while holding
down SHIFT).
TEST TONE (SHIFT + 4) (page 60)
Use to output the test tone (for speaker
setup).
CH LEVEL (SHIFT + 5) (page 60)
Use to adjust the speaker level.
TIMER (SHIFT + 6) (page 55)
Press to display the clock and to access the
timer menu.
SR+ (SHIFT + 7) (page 17)
Press to switch SR+ on or off.
DISPLAY (SHIFT + 8) (page 52)
Press to display/change disc information
shown on-screen.
DIMMER (SHIFT + 9)
Press to switch between normal and
dimmed front panel display.
CLEAR
Press to clear an entry.
ENTER
Press to select menu options, etc. (works
exactly the same as the ENTER button in 13
above).
25
En
XV-HTD340.book 26 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
Chapter 4
Getting started
Switching on and setting up
After making sure everything is connected up
properly, you’re ready to switch on. The first
thing to do is to tell the system what kind of TV
you’re using, standard or widescreen.
After that you can set up the surround sound
for your room, and set the clock so that you can
use the timer features.
1 Press STANDBY/ON (on the remote or
on the front panel) to switch the system
on.
Also make sure that your TV is switched on and
that the video input is set to this system. You
should see the welcome screen displayed.
Welcome to Pioneer DVD!
Thank you for purchasing this Pioneer DVD player.
Before using, please take a little time
to setup your DVD player
Put the batteries into the remote control
STANDBY/ON
Next, press the [ENTER] button on the remote control
and start the Let's Get Started Menu
Next
ROOM
SETUP
2 Press ENTER to move on to the next
screen.
SYSTEM SETUP
3 Use the / (cursor left/right) buttons
to select either ‘Wide screen’ or ‘Standard
size screen’ according to the kind of TV you
have, then press ENTER.
See also Screen sizes and disc formats on
page 77 if you’re not sure which one to choose.
ENTER
TIMER
ENTER
Let's Get Started Menu
What kind of TV do you have?
SHIFT
Use the
/
cursor buttons
to choose, then press ENTER
Wide screen (16:9)
26
En
Standard size screen (4:3)
XV-HTD340.book 27 ページ 2003年12月27日 土曜日 午前10時30分
Getting started
4
04
Press ENTER again to finish setting up.
Let's Get Started Menu
2 If ‘Clock ADJ?’ isn’t already shown in
the display, press or (cursor left or
right) until you see it.
3
Setup complete
choose [Complete],
to start again choose [Back]
5
Complete
Press ENTER.
4 Use the / (cursor up/down) buttons
to set the hour.
If you're finished setting up,
Back
• Use the (cursor right) button to select
BACK then press ENTER if you want to go
back and change the setting you just
made.
Press ENTER.
6 Use the / (cursor up/down) buttons
to set the minute.
7 Press ENTER to confirm.
The display flashes to indicate the clock is set.
• Press TIMER (SHIFT + 6) anytime to
display the clock.
• You can also use the OPEN/CLOSE
button on the front panel or the function
buttons (DVD/CD, TUNER, etc.) to switch
the system on from standby.
• The system switches on, but there is
nothing displayed on my TV.
Make sure that the TV is set to the correct
video input (not a TV channel). For
example, if you connected this system to
the VIDEO 1 input on your TV, switch your
TV to VIDEO 1.
Setting the clock
• If you unplug the system from the wall
outlet, or there is a power outage, you will
need to set the clock again.
Using the Room Setup
After you have set up your speakers to your
liking (see Placing the speakers on page 11),
make sure you calibrate your system for
surround sound. This is a quick and easy way
to get good surround sound for your room.
For more detailed surround sound setup, see
Surround sound and other settings on page 58.
Setting the clock allows you to use the timer
features.
1 If the system isn’t already on, press
STANDBY/ON to switch it on.
1
2
Press TIMER (SHIFT + 6).
• If you are adjusting the clock, rather then
setting it for the first time, press TIMER
(SHIFT + 6) again.
Press ROOM SETUP.
• If you have previously set up the room type
and seating position, the display will show
the current room settings.
27
En
XV-HTD340.book 28 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
3
Press ENTER.
4 Use the / (cursor up/down) buttons
to select a room type then press ENTER.
Choose one of the following depending on your
room size:
• S – Smaller than average room
• M – Average room
• L – Larger than average room
5 Use the / (cursor up/down) buttons
to select a seating position setting, then
press ENTER.
Choose one of the following depending on
where your main listening position is:
• Fwd – If you are nearer to the front
speakers than the surround speakers
• Mid – If you are equal distance from the
front and surround speakers
• Back – If you are nearer to the surround
speakers than the front speakers
• The Room Setup automatically sets up
channel levels and channel delay. If you
have already set the channel levels
manually (see Setting the channel levels on
page 60), you will see Room Set? in the
display when you first press the ROOM
SETUP button. If you continue, the previous
settings will be overwritten.
1
Switch on your TV.
2 Find the name of the manufacturer of
your TV in the Preset Code List on page 79.
Next to each manufacturer is one or more
three digit codes. These tell the remote what
kind of TV you have.
If the name of the manufacturer of your TV
does not appear in the table, you won’t be able
to set up this remote to control your TV. Note
that there are also cases where the preset
codes listed for a manufacturer in the table
may not work for your TV.
3 Point the remote at your TV, hold down
the CLEAR button, then enter the three
digit code for your TV.
The remote transmits an on/off signal to the TV.
If you’ve entered the correct code, your TV
should switch off.
If your TV doesn’t turn off, repeat the procedure
using the next code in the list until your TV
switches off successfully. Once set, you can
then use the individual TV controls shown
below.
TV CONTROL
INPUT
CHANNEL
VOLUME
Button
What it does
Switches your TV on or into
standby.
CHANNEL +/– Changes the TV channel.
Setting up the remote to
control your TV
You can set up the supplied remote to control
your TV using the TV CONTROL buttons.
VOLUME +/–
Adjusts the volume.
INPUT
Switches the TV’s input
between the built in TV tuner
and an external video source.
• The default setting is for a Pioneer TV.
28
En
XV-HTD340.book 29 ページ 2003年12月27日 土曜日 午前10時30分
Getting started
04
Using the on-screen displays
For ease of use, this system makes extensive
use of graphical on-screen displays (OSDs).
You should get used to the way these work as
you’ll need to use them when setting up the
system, using some of the playback features,
such as program play, and when making more
advanced settings for audio and video.
All the screens are navigated in basically the
same way, using the cursor buttons to change
the highlighted item and pressing ENTER to
select it.
• Throughout this manual, ‘Select’ means
use the cursor buttons to highlight an item
on-screen, then press ENTER.
• The button guide at the bottom of every
OSD screen shows you which buttons
you’ll need to use for that screen.
Playing discs
HOME
MENU
ENTER
RETURN
The basic playback controls for playing DVD,
CD, Video CD and WMA/MP3 discs are
covered here. Further functions are detailed in
chapter 6.
STANDBY/ON
OPEN/CLOSE
DVD/CD
ENTER
Button
What it does
HOME
MENU
Displays/exits the on-screen
display
Changes the highlighted menu
item
ENTER
Selects the highlighted menu
item (both ENTER buttons work
in exactly the same way)
RETURN
Returns to the main menu
without saving changes
DISC 1
DISC 2
DISC 3
CD MODE
DISC 4
DISC 5
DISC SKIP
VOLUME
ENTER
1 If the system isn’t already on, press STANDBY/ON to switch on.
If you’re playing a DVD or Video CD, also turn
on your TV and make sure that it is set to the
correct video input.
29
En
XV-HTD340.book 30 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
2 Press OPEN/CLOSE to open the disc
tray.
3 Load a disc.
Load a disc with the label side facing up in the
front-most disc space, using the disc tray
guide to align the disc. (If you’re loading a
double-sided DVD disc, load it with the side you
want to play face down.)
If you’re playing a DVD or Video CD, a menu
may appear. See DVD-Video disc menus on
page 33 and Video CD PBC menus on page 34
for how to navigate these.
If you’re playing an MP3, WMA or JPEG disc, it
may take a few seconds before playback starts,
depending on the complexity of the file
structure on the disc.
If you loaded a CD/CD-R/RW containing
JPEGs, a slideshow will start. See Viewing JPEG
discs on page 53 for more on playing these
discs.
• See also Options on page 65 if the disc
contains both WMA/MP3 audio files and
JPEG picture files.
Disc number
If you want to load more discs, press DISC SKIP
(remote or front panel) to rotate the disc tray.
You can load up to five discs at once.
• Do not place discs in the two partially
accessible disc spaces, as it easy to
misalign them. Use only the front-most
space.
5 Use the VOLUME +/– button (or the
front panel VOLUME knob) to adjust the
volume.
Basic playback controls
The following table shows the basic controls on
the remote for playing discs. You can find other
playback features in Playing discs on page 43.
• Do not load more than one disc in a space.
ENTER
• Before loading or removing discs, always
wait for the disc mechanism to come to a
complete stop.
• Do not rotate the disc tray by hand. Always
use the DISC SKIP button.
• Sometimes, when the disc tray
mechanism is moving, the controls are
inoperative.
4 Press (remote) or (front panel) to
start playback of the disc loaded in the
front-most disc space.
Alternatively, use the DVD/CD or DISC buttons
on the remote, or the DIRECT PLAY buttons on
the front panel to start playback of other discs.
30
En
FOLDER
FOLDER
ENTER
XV-HTD340.book 31 ページ 2003年12月27日 土曜日 午前10時30分
Getting started
04
Button
What it does
Button
What it does
Starts playback.
DVD and Video CD: If the display
shows Resume or Last Mem
playback starts from the resume
or last memory point (see also
Resume and Last Memory
below.)
Numbers
Pauses a disc that’s playing, or
restarts a paused disc.
Use to enter a title/track number. Press ENTER to select (or
wait a few seconds).
• If the disc is stopped, playback starts from the selected
title (for DVD) or track number
(for CD/Video CD/WMA/MP3).
• If the disc is playing, playback
jumps to the start of the
selected chapter or track.
Stops playback.
DVD and Video CD: The display
shows Resume. Press again
if you want to cancel the resume
function. (See also Resume and
Last Memory below.)
Press to start fast reverse
scanning. Press (play) to
resume normal playback.
• You may find with some DVD discs that
some playback controls don’t work in
certain parts of the disc. This is not a
malfunction.
Using the front panel controls
The OPEN/CLOSE and (stop) buttons on
the front panel work the same way as the
remote control equivalents.
Press to start fast forward
scanning. Press (play) to
resume normal playback.
Skips to the start of the current
track or chapter, then to
previous tracks/chapters.
The front panel scan and skip buttons (
and ) are combined. Press once for
chapter/track skip, or press and hold for
scanning.
Skips to the next track or
chapter.
Resume and Last Memory
FOLDER +/– Skips to the next/previous folder
when playing MP3 or WMA
discs.
When you stop playback of a DVD or Video CD
disc, Resume is shown in the display indicating that you can resume playback again
from that point.
If the disc tray is not opened, the next time you
start playback the display shows Resume and
playback resumes from the resume point.
31
En
XV-HTD340.book 32 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
For DVD discs only: If you change discs using
the DISC SKIP, DISC or DIRECT PLAY buttons,
or take the disc out of the player, the play position is stored in memory. When you load the
disc next time, the display shows Last Mem
and you can resume playback (this works for
up to five discs).
2 Load a disc with the label side facing
up, using the disc tray guide to align the
disc.
If you want to clear the resume/last memory
point, press (stop) while Resume or Last
Mem is displayed.
• When a Video CD is loaded, the Resume
point is lost if the system is switched off, or
switched to a function other than DVD/CD.
• For the Last Memory function to work, you
must press (stop) to stop playback
before opening the disc tray or changing
the disc.
• The Last Memory function doesn’t work
with VR format DVD-RW discs.
Changing discs
You can change any of the discs not in the play
position using the EXCHANGE button on the
front panel. Because the disc in the play
position is unaffected, you can use this button
to change discs even during playback.
1
Press EXCHANGE to open the disc tray.
• The EXCHANGE button only works when
there is at least one disc loaded.
Disc number
• If you want to load more discs, press DISC
SKIP to rotate the disc tray two disc spaces.
• Before loading or removing discs, always
wait for the disc mechanism to come to a
complete stop.
• Load discs only in the two fully accessible
disc spaces. Do not try and load discs into
any of the other spaces; they may not load
correctly and cause the system to
malfunction.
• Do not rotate the disc tray by hand. Always
use the DISC SKIP button.
• Do not obstruct the movement of the disc
tray.
3 Press EXCHANGE or OPEN/CLOSE to
close the disc tray.
• Always use the OPEN/CLOSE or
EXCHANGE button to close the disc tray
after exchanging discs. Never push the
disc tray shut by force.
• After I load a DVD disc, it ejects
automatically after a few seconds!
32
En
XV-HTD340.book 33 ページ 2003年12月27日 土曜日 午前10時30分
Getting started
Most likely, the disc is the wrong region for
your system. The region number should be
printed on the disc; check it against the
region number of the system (which you
can find on the rear panel). See also DVD
Video regions on page 68.
If the region number is OK, it may be that
the disc is damaged or dirty. Clean the disc
and look for signs of damage. See also
Using and taking care of discs on page 68.
• Why won’t the disc I loaded play?
04
DVD-Video disc menus
Many DVD-Video discs contain menus from
which you can select what you want to watch.
They may give access to additional features,
such as subtitle and audio language selection,
or special features such as slideshows. See the
disc packaging for details.
Sometimes DVD-Video menus are displayed
automatically when you start playback; others
only appear when you press DVD MENU or
TOP MENU.
First check that you loaded the disc the
right way up (label side up), and that it’s
clean and not damaged. See Using and
taking care of discs on page 68 for
information on cleaning discs.
TOP MENU
DVD MENU
ENTER
If a disc loaded correctly won’t play, it’s
probably an incompatible format or disc
type, such as DVD Audio or DVD-ROM. See
Disc / content format playback compatibility
on page 8 for more on disc compatibility.
RETURN
• I have a widescreen TV so why are there
black bars at the top and bottom of the
screen when I play some discs?
ENTER
SHIFT
Some movie formats are such that even
when played on a widescreen TV, black
bars are necessary at the top and bottom of
the screen. This is not a malfunction.
• I have a standard (4:3) TV and set the system
to show widescreen DVDs in pan & scan
format, so why do I still get black bars top
and bottom with some discs?
Some discs override the display
preferences of the system, so even if you
have 4:3 (Pan & Scan) selected, those
discs will still be shown in letterbox format.
This is not a malfunction.
Button
What it does
TOP MENU Displays the ‘top menu’ of a DVD
(SHIFT +
disc—this varies with the disc.
DVD
MENU)
DVD
MENU
Displays a DVD disc menu—this
varies with the disc and may be
the same as the ‘top menu’.
Moves the cursor around the
screen.
33
En
XV-HTD340.book 34 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
Button
What it does
Button
What it does
ENTER
Selects the current menu option.
RETURN
Returns to the previously
displayed menu screen.
Displays the previous menu page
(if there is one).
Displays the next menu page (if
there is one).
ENTER
Press to select highlighted menu
option.
Numbers
Highlights a numbered menu
option (some discs only). Press
ENTER to select.
Video CD PBC menus
Listening to the radio
Some Video CDs have menus from which you
can choose what you want to watch. These are
called PBC (Playback control) menus.
The tuner can receive both FM and AM
broadcasts, and lets you memorize your
favorite stations so you don’t have to manually
tune in every time you want to listen.
You can play a PBC Video CD without having to
navigate the PBC menu by pressing (stop)
then starting playback using a number button
to select a track, rather than (play) (or on the front panel).
STANDBY/ON
FM/AM
TUNER
ENTER
RETURN
SYSTEM SETUP
TUNE +
ST –
ENTER
ST +
RETURN
TUNE –
ENTER
ENTER
SHIFT
34
En
Button
What it does
RETURN
Displays the PBC menu.
Numbers
Selects a numbered menu
option.
XV-HTD340.book 35 ページ 2003年12月27日 土曜日 午前10時30分
Getting started
04
1 If the system isn’t already on, press
STANDBY/ON to switch on.
1 Press SYSTEM SETUP (SHIFT + HOME
MENU).
2 Press TUNER to switch to the tuner,
then press repeatedly to select the AM or
FM band.
The display indicates the tuner band and the
frequency.
2 Use the / (cursor left/right) buttons
to choose ‘FM Mode ?’, then press ENTER.
• If you’re using the front panel controls, the
TUNER button switches between FM, AM
and station presets (see Memorizing
stations on page 35).
3 Tune to a frequency.
There are three tuning modes—manual, auto,
and high-speed:
• Manual tuning: Press TUNE +/–
repeatedly to change the displayed
frequency.
• Auto tuning: Press and hold TUNE +/–
until the frequency display starts to move,
then release. The tuner will stop on the next
station it finds. Repeat to search for other
stations.
• High-speed tuning: Press and hold TUNE
+/– until the frequency display starts to
move rapidly. Keep the button held down
until you reach the frequency you want. If
necessary, fine tune the frequency using
the manual tuning method.
3 Use the / (cursor up/down) buttons
to select ‘FM Mono’ or ‘FM Auto’, then
press ENTER.
Select Auto in step 3 to switch back to autostereo mode (the stereo indicator lights when
receiving a stereo broadcast).
Memorizing stations
You can save up to 30 station presets so that
you always have easy access to your favorite
stations without having to tune in manually
each time.
1 Tune to an AM or FM radio station.
For the FM band, select mono or auto-stereo
reception as necessary. This setting is saved
along with the preset.
2 Press SYSTEM SETUP (SHIFT + HOME
MENU).
3 Use the / (cursor left/right) buttons
to choose ‘St. Memory?’ then press ENTER.
4 Use the / (cursor up/down) buttons
to select the station preset you want.
There are 30 preset locations; each can store
one station preset.
5
Press ENTER to save the station preset.
• You can use the and buttons on the front panel instead of the
TUNE +/– buttons.
Improving poor FM reception
If you’re listening to an FM station in stereo but
the reception is weak, you can improve the
sound quality by switching to mono.
• If the system is unplugged from the power
supply completely, saved stations will
remain for several days, after which you’ll
have to save them again.
35
En
XV-HTD340.book 36 ページ 2003年12月27日 土曜日 午前10時30分
04
Getting started
Listening to station presets
1 Make sure the TUNER function is
selected.
2 Use ST +/– or the number buttons to
select a station preset.
• If you are using the front panel controls,
press TUNER FM/AM/ST. until you’re in
station preset mode, then use the and buttons to select a station
preset.
Listening to other sources
You can connect up to three external sources
(TV, satellite receiver, etc.) to this system,
including one digital source. See also Listening
to TV audio through this system on page 16 and
Connecting auxiliary components on page 71.
STANDBY/ON
L1/L2
TV
LINE
1 If the system isn’t already on, press STANDBY/ON to switch on.
Also make sure that the external source (TV,
satellite receiver, etc.) is switched on.
2
Select the source you want to listen to.
• If you’re using the remote control, press TV
to select the TV input, or use the LINE (L1/
L2) button to select the LINE 1 or LINE 2
input.
• The TV/L1/L2 button on the front panel
switches between the three inputs.
3 If necessary, start playback of the
external source.
36
En
XV-HTD340.book 37 ページ 2003年12月27日 土曜日 午前10時30分
Listening to your system
05
Chapter 5
Listening to your system
About the listening modes
Auto listening mode
As explained in Placing the speakers on
page 11, there are two basic surround speaker
setup options available. Of course you can
select any of the listening modes regardless of
how you place your speakers, but you will
achieve the best surround effect by using the
listening modes in conjunction with your
speaker setup:
The Auto listening mode is the simplest way to
listen to any source as it was mastered: the
output from the speakers mirrors the channels
from the source material.
• Standard surround 5-spot setup – Use
the Standard (Listening in surround sound
on page 38) and Advanced (Using the
Advanced Surround effects on page 39)
surround listening modes with this setup.
• Front surround 3-spot setup – See Using
Front Surround on page 39 for the options
available with this speaker setup.
Make sure you have completed Using the
Room Setup on page 27. For a more detailed
surround sound setup, see Using the System
Setup menu on page 58.
SURROUND
• Press SURROUND to select the ‘Auto’
listening mode.
If the source is Dolby Digital or DTS, the
2 DIGITAL or DTS indicator on the front panel
lights.
• Any previously active Dolby Pro Logic or
Advanced Surround mode is canceled
when Auto listening mode is selected.
• Certain features explained in this section
may not be possible depending on the
source (for example, 88.2 / 96 kHz sources),
or a conflicting system setting. See Error
Messages on page 76 for more on this.
37
En
XV-HTD340.book 38 ページ 2003年12月27日 土曜日 午前10時30分
05
Listening to your system
Listening in surround sound
You can listen to any source—stereo or
multichannel, analog or digital—in surround
sound. Surround sound is generated from
stereo sources using one of the Dolby Pro
Logic decoding modes.
• When listening in Dolby Digital / DTS
mode, two-channel material will
automatically be played in surround sound
using Dolby Pro Logic II decoding.
• Dolby Digital / DTS sources that use only
the center channel cannot be played back
in surround sound.
SURROUND
Dolby Pro Logic II Music settings
When listening in Dolby Pro Logic II Music
mode, there are three further parameters you
can adjust: Center Width, Dimension, and
Panorama.
• Press SURROUND repeatedly to select a
listening mode (or press SURROUND then
use the / (cursor up/down) buttons).
The listening mode choices that appear in the
display will vary according to the type of source
that’s playing.
1 With Dolby Pro Logic II Music mode
active, press SOUND MODE.
2 Use the / (cursor left/right) buttons
to select ‘C Width’, ‘Dimen.’ or ‘Pnrm.’
• C Width (Center Width): Makes the center
channel wider (higher settings) or
narrower (lower settings)
• Dimen. (Dimension): Makes the sound
more distant (minus settings), or more
forward (positive settings)
• Auto – See Auto listening mode above.
• Dolby Digital / DTS – Dolby Digital or DTS
decoding (depending on the source).
• Pnrm. (Panorama): Creates more spacious
surround sound
• Pro Logic – 4.1 channel surround sound
for use with any two-channel source
• PL II Movie – Pro Logic II 5.1 channel
surround sound, especially suited to movie
sources, for use with any two-channel
source
• PL II Music – Pro Logic II 5.1 channel
surround sound, especially suited to music
sources, for use with any two-channel
source (see also Dolby Pro Logic II Music
settings below)
• Stereo – See Listening in stereo below
38
En
3 Use the / (cursor up/down) buttons
to adjust the setting.
Center Width is adjustable between 0 and 7;
Dimension between –3 and +3. Panorama is
On or Off.
4
Press ENTER to confirm.
XV-HTD340.book 39 ページ 2003年12月27日 土曜日 午前10時30分
Listening to your system
Using the Advanced Surround
effects
Advanced Surround effects can be used with
multichannel or stereo sources for a variety of
additional surround sound effects. The 5-spot
setup described in Placing the speakers on
page 11 should be used with these effects.
For more options, see Adjusting the Advanced
and Front Surround effect level below.
05
Using Front Surround
The Front Surround modes are effective when
you are using the Front surround 3-spot
speaker setup as described in Placing the
speakers on page 11. The surround speakers
should be placed on top of the front speakers
and oriented either towards the walls, or
straight ahead, depending on which mode you
are using (see below).
For more options, see Adjusting the Advanced
and Front Surround effect level below.
ADVANCED
FRONT
SURROUND
ENTER
• Press ADVANCED to select an Advanced
Surround mode (or press ADVANCED then
use the / (cursor up/down) buttons).
Press repeatedly to select from:
• Adv. Movie – Gives a movie theater-type
sound
• Adv. Music – Gives a concert hall-type
sound
• Expanded – Creates an extra wide
surround field
• TV Surr. – Designed for mono or stereo TV
broadcasts and other sources
• Sports – Designed for sports and other
programs based on commentary
• Game – Creates surround sound from
video game sources
• Press FRONT SURROUND to select an
Front Surround mode (or press FRONT
SURROUND then use the / buttons).
Press repeatedly to select from:
• Frt. Movie – The Front Surround Movie
mode emphasizes directionality, giving you
a realistic movie theater-type sound.
• Frt. Music – The Front Surround Music
mode provides greater breadth and depth
to music sources, enveloping you with a
concert hall-type sound.
• ExtraPower – The Extra Power mode gives
additional energy and depth to a stereo
source by using the surround speakers in
addition to the front speakers.
• 5ch Stereo – Designed to give powerful
surround sound to stereo music sources
39
En
XV-HTD340.book 40 ページ 2003年12月27日 土曜日 午前10時30分
05
Listening to your system
If you have selected Frt. Movie or Frt. Music,
you will achieve best results by turning each
surround speaker about 60º towards the
closest wall. With ExtraPower, orient the
surround speakers in the same direction as the
front speakers (towards the listening position).
Listening in stereo
You can listen to any source—stereo or
multichannel, analog or digital—in stereo.
When playing a multichannel source, stereo
sound is created by downmixing all channels
to the front left/right speakers and the
subwoofer.
SURROUND
60º
Frt. Movie / Frt. Music
ExtraPower
Adjusting the Advanced and Front
Surround effect level
You can emphasize or reduce the effect of the
Advanced and Front Surround modes as you
like. You can set the effect level for all modes
independently.
1 With one of the Advanced or Front
Surround modes active, press SOUND
MODE.
2 Use the / (cursor left/right) buttons
to select ‘Effect’.
3 Use the / (cursor up/down) buttons
to adjust the effect level.
The effect level can be adjusted from 10 (min)
to 90 (max).
4
40
En
Press ENTER to confirm.
• Press SURROUND repeatedly until
‘Stereo’ shows in the display.
Any active Advanced Surround or Front
Surround mode is canceled.
Listening with headphones
When headphones are connected, only the
Stereo (default) and Phones Surround (virtual
surround sound for headphones) modes are
available.
When you disconnect them it reverts to the
previous mode.
• With headphones connected, press
ADVANCED or FRONT SURROUND to select
‘Phones Surround’ or SURROUND to select
‘Stereo’.
XV-HTD340.book 41 ページ 2003年12月27日 土曜日 午前10時30分
Listening to your system
05
Enhancing dialogue
• Default setting: Dialog Off
The Dialogue Enhancement feature is
designed to make the dialog stand out from
other background sounds in a TV or movie
soundtrack.
DIALOGUE
SHIFT
• Press DIALOGUE (SHIFT + SURROUND)
to select the amount dialog enhancement.
Press repeatedly to select from:
• Dialog Off – No dialog enhancement
• Dialog Mid – Moderate dialog
enhancement
• Dialog Max – Strong dialog enhancement
Listening with a virtual
surround back speaker
• Default setting: Vir. SB Off
The Virtual Surround Back feature can be used
when listening in surround sound (using the 5spot setup described in Placing the speakers on
page 11) to simulate an added surround back
channel. In a real theater the surround back
speaker would be directly behind you, creating
more cohesive and realistic surround sound.
• You can’t use Virtual Surround Back when
using the Stereo listening mode (or Auto
with stereo sources).
• If you are using the The Front surround 3spot setup (see Placing the speakers on
page 11), switch the Virtual Surround
Back feature off.
• If there is no surround channel, Virtual
Surround Back has no effect.
Using Quiet and Midnight
listening modes
• Default setting: Off
The Quiet listening feature reduces excessive
bass or treble in a sound source. You can use
this feature if the music is a little bit harsh and
you would like a smoother sound.
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels. The effect automatically adjusts
according to the volume at which you’re
listening.
QUIET/
MIDNIGHT
• Press QUIET/MIDNIGHT repeatedly to
switch between ‘Quiet’, ‘Midnight’ and
‘Off’.
VIR. SB
SHIFT
• Press VIR. SB (SHIFT + ADVANCED)
repeatedly to switch between ‘Vir. SB On’
and ‘Vir. SB Off’.
41
En
XV-HTD340.book 42 ページ 2003年12月27日 土曜日 午前10時30分
05
Listening to your system
Adjusting the bass and treble
Use the bass and treble controls to adjust the
overall tone.
SOUND
MODE
• Press BASS MODE (SHIFT + FRONT
SURROUND) repeatedly to choose an
option that fits the source you’re listening
to.
• Music – Can be used with music to give a
deeper bass sound
• Cinema – Good for action movies or
movies with lots of sound effects
• P. Bass – Can be used with music sources
to bring the beat of the music (or
soundtrack) to the forefront
• Off – Switch off the bass boost if it causes
excessive bass (i.e. it sounds ‘boomy) in
the source
ENTER
1
Press SOUND MODE.
2 Use the / (cursor left/right) buttons
to select ‘Bass’ or ‘Treble’.
3 Use the / (cursor up/down) buttons
to adjust the sound.
The bass and treble can be adjusted from –3 to
+3.
4
Press ENTER to confirm.
• Bass and treble adjustment is not possible
when the Quiet or Midnight modes are
active.
Boosting the bass level
There are three bass modes you can use to
enhance the bass in a source.
BASS MODE
SHIFT
42
En
XV-HTD340.book 43 ページ 2003年12月27日 土曜日 午前10時30分
Playing discs
06
Chapter 6
Playing discs
• You can't switch on CD mode while playing
a DVD or Video CD. Stop playback first.
• Some DVD discs restrict the use of some
functions (random or repeat, for example).
This is not a malfunction.
• Although program play is not possible in
CD mode, it is possible to program a
playlist. When you start program play-back,
however, CD mode is canceled.
• When playing Video CDs, some of the
functions are not available during PBC
playback. If you want to use them, start the
disc playing using a number button to
select a track.
• Repeat and random play is possible in CD
mode (see Using repeat play on page 45
and Using random play on page 46).
• Many features are not available when
using unfinalized CD-R/RW discs.
Playing only CDs and WMA/
MP3 discs (CD mode)
Using this feature you can play only the CDs
and WMA/MP3 discs loaded in the disc tray—
automatically skipping over any DVDs and
Video CDs loaded. This may be useful if you
have a mixture of discs loaded but only want to
play music: you don't have to keep track of what
kind of disc is where in the disc tray.
1 Press CD MODE (SHIFT + DISC SKIP) to
switch CD mode on.
• The indicator on the front panel lights
when CD mode is on.
2 Press (play) to start playback.
The first CD loaded automatically starts to play.
Once all the CD/WMA/MP3 discs loaded have
played, playback automatically stops.
• To cancel the CD mode, press CD MODE
(SHIFT + DISC SKIP) again.
• If you open the disc tray and load a DVD,
Video CD or JPEG disc in the front-most
position then press (play) (on the front
panel), CD mode is canceled.
Scanning discs
You can fast-scan discs forward or backward at
various different speeds.
1 During playback, press or to
start scanning.
• There is no sound while scanning DVDs
and Video CDs, and no subtitles while
scanning DVDs.
2 Press repeatedly to increase the
scanning speed.
• The scanning speed is shown on-screen.
3
To resume playback, press (play).
• When scanning a Video CD or a WMA/MP3
track, playback automatically resumes at
the end or beginning of the track.
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached on a DVD disc.
Playing in slow motion
You can play DVDs and Video CDs at four
different forward slow motion speeds. DVD
discs can also be played at two reverse speeds.
43
En
XV-HTD340.book 44 ページ 2003年12月27日 土曜日 午前10時30分
06
Playing discs
1
During playback, press (pause).
2 Press and hold / or / until
slow motion playback starts.
• The slow motion speed is shown onscreen.
• There is no sound during slow motion
playback.
3 Press repeatedly to change the slow
motion speed.
4 To resume normal playback, press (play).
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
Frame advance/frame reverse
You can advance or back up DVD discs frameby-frame. With Video CDs you can only use
frame advance.
1
During playback, press (pause).
2 Press / or / to reverse or
advance a frame at a time.
3 To resume normal playback, press (play).
• Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
Using the Disc Navigator to
browse the contents of a disc
Use the Disc Navigator to browse through the
contents of a disc to find the part you want to
play. You can use the Disc Navigator when a
disc is playing or stopped (a disc must be
loaded).
1 Press HOME MENU and select ‘Disc
Navigator’ from the on-screen display.
Disc Navigator
44
En
• With most discs, you can also press DVD
MENU to go directly to the Disc Navigator.
2 Select what you want to play.
Depending on the type of disc you have loaded,
the Disc Navigator looks slightly different.
The screen for DVD discs shows the titles on
the left and the chapters on the right. Select a
title, or a chapter within a title.
Disc Navigator
DVD
Title 1-10
Chapter 1-3
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
For a VR format DVD-RW disc select between
the PlayList and Original areas of the disc, or
a title. Press (cursor right) to preview the
title.
• You can’t switch between Original and
PlayList during playback.
• Not all VR format DVD-RW discs have a
Playlist.
Disc Navigator
DVD-RW
Original
Play List
Title(1-03)
01. 3/31 FIRST LEAGUE
02. 4/28 SECOND LEAGUE
03. 4/29 FINAL ROUND
The screen for CDs and Video CDs shows a list
of tracks.
Disc Navigator
Track 1-10
CD
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
Track 07
Track 08
XV-HTD340.book 45 ページ 2003年12月27日 土曜日 午前10時30分
Playing discs
06
The screen for WMA/MP3 discs shows the
folder names on the left and the track names
on the right (note that any folder and track
names that contain accented or non-roman
characters, will show up with generic names –
F_033, T_035, etc.).
1 During playback, press HOME MENU
and select ‘Play Mode’.
2 Select ‘A-B Repeat’ from the list of
functions on the left.
Play Mode
Select a folder, or a track within a folder.
Disc Navigator
WMA/MP3
Folder 1-17
Track 1-10
001. ACP
002. Nth Degree
003. Pfeuti
004. Live
005. Glitch music
006. CodHead
007. Thermo
008. Missing Man
001. Gravity deluxe
002. Tesla's patent
003. Border dispute
004. Delayed by rain
005. Accident incident
006. Pigeon post
007. Outernational
008. Vacuum tube
Playback starts after you press ENTER.
• Another way to find a particular place on a
disc is to use one of the search modes. See
Searching a disc on page 50.
A-B Repeat
Repeat
Random
Program
Search Mode
A(Start Point)
B(End Point)
Off
3 Press ENTER on ‘A(Start Point)’ to set
the loop start point.
4 Press ENTER on ‘B(End Point)’ to set the
loop end point.
After pressing ENTER, playback jumps back to
the start point and plays the loop.
• The minimum loop time is 2 seconds.
5 To resume normal playback, select ‘Off’
from the menu.
Looping a section of a disc
Using repeat play
The A-B Repeat function allows you to specify
two points (A and B) within a track (CD and
Video CD) or title (DVD) that form a loop which
is played over and over.
There are various repeat play options,
depending on the kind of disc loaded. It’s also
possible to use repeat play together with
program play to repeat the tracks/chapters in
the program list (see Creating and editing a
DVD program list on page 47 and Creating and
editing a non-DVD program list on page 48).
• You can’t use A-B Repeat with WMA/MP3
discs.
45
En
XV-HTD340.book 46 ページ 2003年12月27日 土曜日 午前10時30分
06
Playing discs
1 During playback, press HOME MENU
and select ‘Play Mode’.
• If you’ve created a program list, Program
Repeat is also available.
2 Select ‘Repeat’ from the list of functions
on the left.
• During random playback (see below),
Random Repeat is also available.
Using random play
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Title Repeat
Chapter Repeat
Repeat Off
3 Select a repeat play option.
If program play is active, select Program
Repeat to repeat the program list, or Repeat
Off to cancel.
• For DVD discs, select Title Repeat or
Chapter Repeat (or Repeat Off).
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Title Repeat
Chapter Repeat
Repeat Off
With a DVD you can choose to play titles or
chapters within a title in a random order. With
CDs, Video CDs, MP3 or WMA discs, you can
play all the discs at random, or just the
contents of a single disc.
You can set the random play option when a
disc is playing or stopped. However, you can't
use random play together with program play.
• You can’t use random play with VR format
DVD-RW discs, or while a DVD disc menu
is being displayed.
1 Press HOME MENU and select ‘Play
Mode’.
2 Select ‘Random’ from the list of
functions on the left.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
• For CDs and Video CDs, select All Discs
Repeat, Disc Repeat or Track Repeat (or
Repeat Off).
• For WMA/MP3 discs, select All Discs
Repeat, Disc Repeat, Folder Repeat or
Track Repeat (or Repeat Off).
3
Random Title
Random Chapter
Random Off
Select a random play option.
• For DVD-Video discs, select Random Title
or Random Chapter (or Random Off)
Play Mode
• You can also use the REPEAT (SHIFT + 2)
button on the remote to select a repeat play
mode. The repeat mode is indicated in the
front panel display and on-screen. The
repeat modes available are the same as
when choosing from the Play Mode menu.
46
En
A-B Repeat
Repeat
Random
Program
Search Mode
Random Title
Random Chapter
Random Off
XV-HTD340.book 47 ページ 2003年12月27日 土曜日 午前10時30分
Playing discs
• For CDs, Video CDs and WMA/MP3 discs,
select Random All, Random Disc (or
Random Off).
• The Random All function ignores DVDs
loaded in the player.
• Use the following controls during random
play:
Button
What it does
Stop and cancel random play.
Selects another track/chapter at
random from those remaining.
Returns to the beginning of the
current track/chapter. You can't
go back further than this.
• You can also use the RANDOM (SHIFT +
3) button on the remote to select a random
play mode. The random mode is indicated
in the front panel display and on-screen.
The random modes available are the same
as when choosing from the Play Mode
menu. Press ENTER to start random play.
• To cancel random playback without
stopping playback, press CLEAR. The disc
will play to the end, then stop.
Creating and editing a DVD
program list
This feature lets you program the play order of
titles and chapters on the DVD disc currently in
the play position.
If you want to program the play order of CDs,
Video CDs or WMA/MP3 discs, see Creating
and editing a non-DVD program list on page 48.
06
1 Make sure that the DVD disc you want
to make the program list for is in the play
position.
Use the DISC select buttons on the remote, or
the DIRECT PLAY buttons on the front panel to
select the disc.
2 Press HOME MENU and select ‘Play
Mode’.
• Alternatively, press PROGRAM (SHIFT +
1) and skip to step 5.
3 Select ‘Program’ from the list of
functions on the left.
Play Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
A-B Repeat
Repeat
Random
Program
Search Mode
4 Select ‘Create/Edit’ from the list of
program options.
Play Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
A-B Repeat
Repeat
Random
Program
Search Mode
5 Select a title or chapter for the first/
next step in the program list.
Program
Program Step
01.
02.
03.
04.
05.
06.
07.
08.
-01
Disc
. DVD
. CD
. DVD
. ???
. ---
Title 1-38
Chapter 1-4
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
Chapter 004
• You can’t use Program play with VR format
DVD-RW discs, or while a DVD disc menu
is being displayed.
47
En
XV-HTD340.book 48 ページ 2003年12月27日 土曜日 午前10時30分
06
Playing discs
• When this screen first appears, the first
title on the disc is highlighted. From here
you can select a title, or a chapter within a
title.
• Some titles and/or chapters of DVD discs
may be grayed out, depending on the disc.
Grayed out titles/chapters can’t be added
to the program list.
6 Press ENTER to add the highlighted
item to the program list.
The program step number automatically
moves to the next position.
Program
Program Step
01.
02.
03.
04.
05.
06.
07.
08.
-01
Disc
. DVD
. CD
. DVD
. ???
. ---
Title 1-38
Chapter 1-4
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 001
Chapter 002
Chapter 003
Chapter 004
7 Add further items to the program list in
the same way.
• A program list can contain up to 24 steps.
• To clear a step in the program list, move to
the Program Step column, highlight the
step to clear and press CLEAR.
• To insert a step in the program list, move to
the Program Step column and highlight
the step where you want a new step to
appear. After you select a title/chapter, all
the program steps will move down one to
make space for the new one.
8
48
En
To play the program list, press (play).
• Program play remains active until you turn
off program play (see below), erase the
program list (see below), or switch off the
system.
Creating and editing a nonDVD program list
This feature lets you program the play order of
folders and tracks on the CDs, Video CDs and
WMA/MP3 discs loaded.
If you want to program the play order of a DVD
disc, see Creating and editing a DVD program
list on page 47.
1 Make sure that a non-DVD disc is in the
play position.
Use the DIRECT PLAY buttons on the front
panel to select a disc.
2 Press HOME MENU and select ‘Play
Mode’.
• Alternatively, press PROGRAM (SHIFT +
1) and skip to step 5.
3 Select ‘Program’ from the list of
functions on the left.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
4 Select ‘Create/Edit’ from the list of
program options.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
Create/Edit
Playback Start
Playback Stop
Program Delete
XV-HTD340.book 49 ページ 2003年12月27日 土曜日 午前10時30分
Playing discs
06
5 Select a folder or track for the first/next
step in the program list.
Program
Program Step
01.
02.
03.
04.
05.
06.
07.
08.
-01
Disc
. WMA/MP3
. CD
. DVD
. ???
. ---
Folder 1-6
Track 1-10
001. Electro A-M
002. Electro N-Z
003. Rock 1
004. Rock 2
005. Jazz
006. Classical
001. Gravity Deluxe
002. Tesla's Patent
003. Border Dispute
004. Delayed by Rai
005. Pigeon Post
006. Outernational
007. Panic Button
008. Accident Incide
• When this screen first appears, the first
folder or track of the disc in the play
position is highlighted. From here you can
select something on this disc, or move left
to the Disc column and select something
from one of the other discs loaded.
6 Press ENTER to add the highlighted
item to the program list.
The program step number automatically
moves to the next position.
Program
Program Step
01.
02.
03.
04.
05.
06.
07.
08.
. WMA/MP3
. CD
. DVD
. ???
. ---
Folder 1-6
Track 1-10
001. Electro A-M
002. Electro N-Z
003. Rock 1
004. Rock 2
005. Jazz
006. Classical
001. Gravity Deluxe
002. Tesla's Patent
003. Border Dispute
004. Delayed by Rai
005. Pigeon Post
006. Outernational
007. Panic Button
008. Accident Incide
• To clear a step in the program list, move to
the Program Step column, highlight the
step to clear and press CLEAR.
• With CDs and Video CDs, select a track.
• To insert a step in the program list, move to
the Program Step column and highlight
the step where you want a new step to
appear. After you select a folder/track, all
the program steps will move down one to
make space for the new one.
• Any DVDs loaded are shown grayed out
and can’t be selected.
• If a tray position is empty, ‘– – –’ is
displayed.
Disc
7 Add further items to the program list in
the same way.
• A program list can contain up to 24 steps.
• With WMA/MP3 discs, you can select a
folder, or an individual track in a folder.
• If the system has not yet determined the
type of disc in a tray position, ‘???’ is
displayed as the disc type. If you select it,
‘??? 1-999’ is displayed in the middle and
right columns. You can add items to the
program list from this disc, although what
you select must actually exist on the disc
for it to play. Also, if the disc is a DVD,
program play will be canceled when it
comes to that disc in the program list
-001-003
-001-003
8
To play the program list, press (play).
• Program play remains active until you turn
off program play (see below), erase the
program list (see below), or switch off the
system.
• Use the following controls during program
play:
Button
What it does
HOME
MENU
Save the program list and exit
the program edit screen without
starting playback.
Skip to the next step in the
program list.
49
En
XV-HTD340.book 50 ページ 2003年12月27日 土曜日 午前10時30分
06
Playing discs
Button
What it does
CLEAR
Switch off program play. Press
while stopped to erase the
program list.
RETURN
Exit the program edit screen
without saving any changes.
1 Press HOME MENU and select ‘Play
Mode’.
2 Select ‘Search Mode’ from the list of
functions on the left.
The search options that appear depend on the
kind of disc loaded. The screen below shows
the DVD search options.
Play Mode
A-B Repeat
Repeat
Random
Program
Search Mode
• The current playlist is erased if you change
the type of disc in the play position (DVD or
non-DVD) or select Program Delete from
the Play Mode menu.
• DVD playback follows commands recorded
on the disc. There may be cases where
program play is automatically canceled or
may not work. This is not a malfunction
• With Video CDs that feature PBC playback,
make sure that the disc is stopped before
you start making the program list.
3
Title Search
Chapter Search
Time Search
Select a search mode.
• The disc must be playing in order to use
time search.
4 Use the number buttons to enter a title,
chapter, folder or track number, or a time.
Play Mode
Other functions available from the
program menu
A-B Repeat
Repeat
Random
Program
Search Mode
There are a number of other options in the
program menu in addition to Create/Edit.
• Playback Start – Starts playback of a
saved program list
• Program Delete – Erases the program list
and turns off program play
Searching a disc
50
En
Input Chapter
0 0 1
• For a time search, enter the number of
minutes and seconds into the currently
playing title (DVD) or track (Video CD) you
want playback to resume from. For
example, press 4, 5, 0, 0 to have playback
start from 45 minutes into the disc. For 1
hour, 20 minutes and 30 seconds, press 8,
0, 3, 0.
• Playback Stop – Turns off program play,
but does not erase the program list
You can search DVD discs by title or chapter
number, or by time. CDs can be searched by
track number, and Video CDs by track number
or time. WMA/MP3 discs can be searched by
folder or track number.
Title Search
Chapter Search
Time Search
5
Press ENTER to start playback.
XV-HTD340.book 51 ページ 2003年12月27日 土曜日 午前10時30分
Playing discs
06
Switching subtitles
Some DVD discs have subtitles in one or more
languages; the disc box will usually tell you
which subtitle languages are available. You
can switch subtitle language during playback.
• Press SUBTITLE repeatedly to select a
subtitle option.
Current / Total
Subtitle
1/2
English
Switching audio channels
when playing a Video CD
When playing a Video CD, you can switch
between stereo, just the left channel or just the
right channel.
• Press AUDIO repeatedly to select an
audio channel option.
Audio
Stereo
Zooming the screen
• Some discs only allow you to change
subtitle language from the disc menu.
Press DVD MENU to access.
Using the zoom feature you can magnify a part
of the screen by a factor of 2 or 4, while
watching a DVD or Video CD.
• To set subtitle preferences, see Language
settings on page 64.
1 During playback, use the ZOOM button
to select the zoom factor (Normal, 2x or
4x).
• Since DVD and Video CD has a fixed
resolution, picture quality will deteriorate,
especially at 4x zoom. This is not a
malfunction.
Switching DVD audio
language
When playing a DVD disc recorded with dialog
in two or more languages, you can switch
audio language during playback.
• Press AUDIO repeatedly to select an
audio language option.
Audio
Current /Total
1/2
French
Dolby Digital 3/2.1CH
• Some discs only allow you to change audio
language from the disc menu. Press DVD
MENU to access.
• To set audio language preferences, see
Language settings on page 64.
2 Use the cursor buttons to change the
zoomed area.
You can change the zoom factor and the
zoomed area freely during playback.
• If the navigation square at the top of the
screen disappears, press ZOOM again to
display it.
• If you are displaying subtitles, these will
disappear when the screen is zoomed.
They will reappear when you return the
screen to normal.
Switching camera angles
Some DVD discs feature scenes shot from two
or more angles—check the disc box for details.
51
En
XV-HTD340.book 52 ページ 2003年12月27日 土曜日 午前10時30分
06
Playing discs
When a multi-angle scene is playing, a
icon appears on screen and in the front panel
display to let you know that other angles are
available (this can be switched off if you
prefer—see Display settings on page 64).
1
4
1 16
Disc no.
Track no.
Elapsed track time
• During playback (or when paused),
press ANGLE to switch angle.
1
4
3 20
Disc no.
Track no.
Remaining track time
Displaying disc information
1 Ds c
53 15
OSD disc information
Various track, chapter and title information
can be displayed on-screen while a disc is
playing.
• To show/switch/hide the information
displayed, press DISPLAY (SHIFT + 8)
repeatedly.
• When a disc is playing, the information
appears at the top of the screen.
Front panel display information
Limited disc information also appears in the
front panel display. Press DISPLAY (SHIFT +
8) to change the displayed information.
• DVD / DVD-RW displays
2
52
En
• CD and Video CD displays
2
8 49
Disc no.
Chapter no.
Elapsed title time
2 T 1 1 07 00
Disc no.
Title no.
Remaining title time
2
Disc no.
Chapter no.
Remaining chapter
time
2
0 42
Disc no.
Remaining disc time
• WMA/MP3 disc displays
4
2
0 35
Disc no.
Track no.
Elapsed track time
4 EVERYBOD
Disc no.
Track name
4 BE S T_OF_
Disc no.
Folder name
• JPEG disc displays
2 T I GER_01
Disc no.
File name
2 ZOO_TR I P
Disc no.
Folder name
XV-HTD340.book 53 ページ 2003年12月27日 土曜日 午前10時30分
Viewing JPEG discs
07
Chapter 7
Viewing JPEG discs
Playing a JPEG slideshow
After loading a CD/CD-R/RW containing JPEG
pictures, press (play) to start a slideshow
from the first folder/picture on the disc. The
pictures in each folder are displayed in
alphabetical order.
Pictures are automatically adjusted so that
they fill as much of the screen as possible (if
the aspect ratio of the picture is different to
your TV screen you may notice black bars at the
sides, or at the top and bottom of the screen).
While the slideshow is running:
Button
What it does
Pauses the slideshow; press
again to restart.
Displays the previous picture.
Use with SHIFT to jump to the
first file in the previous folder.
Displays the next picture.
Use with SHIFT to jump to the
first file in the next folder.
ANGLE
ZOOM
DVD
MENU
Pauses the slideshow and
rotates the currently displayed
picture 90º clockwise. Press (play) to restart slideshow).
Pauses the slideshow and zooms
the screen (see below). Press (play) to restart slideshow).
Displays the Disc Navigator
screen (see below).
FOLDER +/ Skips to the next/previous folder
FOLDER – when playing a JPEG disc.
• The (pause), ANGLE and ZOOM buttons
do not work while the display shows
LOADING.
• The time it takes for a file to load increases
with large file sizes.
• Up to 999 files are viewable on a disc. If
there are more files than this on a disc, only
the first 999 files are viewable.
• If you want to play the WMA/MP3 tracks on
a disc that also contains JPEG picture files,
you should first set the Photoviewer
option to Off. See Options on page 65.
Using the JPEG Disc Navigator
and Photo Browser
Use the JPEG Disc Navigator to find a
particular folder or picture by filename on the
disc in the play position; use the Photo
Browser to find a picture within a folder by
thumbnail image.
1 Press DVD MENU to display the Disc
Navigator screen.
Disc Navigator
Folder 1-2
JPEG
001. F_001
002. F_002
File 1-40
001. FL000001
002. FL000002
003. FL000003
004. FL000004
005. FL000005
006. FL000006
007. FL000007
008. FL000008
The left column shows the folders on the disc,
the right column shows the files in a folder.
53
En
XV-HTD340.book 54 ページ 2003年12月27日 土曜日 午前10時30分
07
Viewing JPEG discs
2 Use the cursor buttons (///) to
navigate.
When a file is highlighted, a thumbnail image
is displayed.
• When a folder is highlighted you can press
ENTER to open the Photo Browser screen
for that folder. See below for more on using
the Photo Browser.
3 To resume the slideshow from the
highlighted file, press ENTER.
Using the Photo Browser
Zooming the screen
Using the zoom feature you can magnify a part
of the screen by a factor of 2 or 4, while viewing
pictures from a JPEG disc.
1 During slideshow playback, use the
ZOOM button to select the zoom factor.
• Normal
• 2x
• 4x
Normal
The Photo Browser displays nine thumbnail
images at a time from the current folder.
1 From the Disc Navigator screen,
highlight a folder to display then press
ENTER.
The Photo Browser screen opens with the first
nine pictures displayed as thumbnails.
Zoom 2x
Zoom 4x
Photo Browser
2 / 40
Live at Soft
• The slideshow is paused when the screen
is zoomed.
2 Use the cursor buttons (///) to
highlight a thumbnail picture.
• Use the track skip buttons ( and ) to
see the previous / next page of thumbnails.
Keep the button pressed if you want to skip
several pages; release when you reach the
page you want.
• To return to the Disc Navigator screen,
press RETURN.
3 Press ENTER to display the selected
thumbnail full size on screen.
The slideshow resumes from the selected
picture.
54
En
• Since JPEG pictures have a fixed
resolution, picture quality may deteriorate,
especially at 4x zoom. This is not a
malfunction.
2 Use the cursor buttons (///) to
change the zoomed area.
You can change the zoom factor and the
zoomed area freely.
3 To resume the slideshow, press (play).
XV-HTD340.book 55 ページ 2003年12月27日 土曜日 午前10時30分
Using the timer
08
Chapter 8
Using the timer
Setting the wake-up timer
Use the wake-up timer to set the system to
switch on at any time and start playing
whatever source you want.
1 Select the source you want played.
For example, press TUNER (TUNER FM/AM/
ST. on the front panel) to select the radio as
your source.
2 Prepare the source.
For example, tune in the radio station you want
to wake up to.
• The clock must be set to the correct time
for the wake-up timer to work properly (see
Setting the clock on page 27).
FM/AM
TUNER
L1/L2
TV
LINE
4 Press TIMER (SHIFT + 6) twice to reach
the timer menu.
6 Use the / (cursor left/right) buttons
to select ‘Timer Edit?’ then press ENTER.
7 Set the switch-on time.
Use the / (cursor up/down) buttons to set
the hour, then press ENTER. Set the minute in
the same way, pressing ENTER when you’re
done.
VOLUME
ENTER
8 Set the switch-off time.
Use the / (cursor up/down) buttons to set
the hour, then press ENTER. Set the minute in
the same way, pressing ENTER when you’re
done.
TIMER
ENTER
SHIFT
Set the volume.
5 Use the / (cursor left/right) buttons
to select ‘Wake-Up?’ then press ENTER.
STANDBY/ON
DVD/CD
3
After pressing ENTER this last time, the wakeup indicator lights, and the switch-on, switchoff times, the function (DVD/CD, etc.) and
volume are confirmed in the display.
9 Switch the system into standby mode.
The wake-up timer will not work if the system is
left on!
55
En
XV-HTD340.book 56 ページ 2003年12月27日 土曜日 午前10時30分
08
Using the timer
Setting the sleep timer
• You can check the timer settings in
standby by pressing TIMER (SHIFT + 6)
twice. (Press TIMER (SHIFT + 6) once to
display the current time.)
Turning the wake-up timer on/off
If the wake-up timer is on, it will switch on the
system everyday at the time you have set.
1 Press TIMER (SHIFT + 6) twice to reach
the timer menu.
2 Use the / (cursor left/right) buttons
to select ‘Wake-Up?’ then press ENTER.
The sleep timer switches off the system after a
specified time so you can fall asleep without
worrying about it.
• If you set the sleep timer while either the
wake-up timer is active, the earlier switch
off time takes priority.
STANDBY/ON
FM/AM
DVD/CD
TUNER
L1/L2
TV
LINE
3 Use the / (cursor left/right) buttons
to select ‘Timer On?’ or ‘Timer Off?’.
• You must have the timer set (see above) to
select On. The wake-up timer switches on
and off according to your previous settings.
4
Press ENTER.
ENTER
• The wake-up timer will automatically be
canceled if the clock is reset.
TIMER
ENTER
SHIFT
56
En
XV-HTD340.book 57 ページ 2003年12月27日 土曜日 午前10時30分
Using the timer
08
1 Press TIMER (SHIFT + 6) twice to reach
the timer menu.
2 Use the / (cursor left/right) buttons
to select ‘Sleep?’ then press ENTER.
3 Use the / (cursor up/down) buttons
to select a switch-off time then press
ENTER.
Choose between the following options:
• Sleep Auto – Available only in CD mode;
the system switches off automatically after
the currently playing disc has finished.
• Sleep 90 – System switches off after 90
minutes
• Sleep 60 – System switches off after an
hour
• Sleep 30 – System switches off after 30
minutes
• Off – cancels the sleep timer
4 To check how much time is left, repeat
steps 1 and 2.
The remaining time is displayed momentarily.
57
En
XV-HTD340.book 58 ページ 2003年12月27日 土曜日 午前10時30分
09
Surround sound and other settings
Chapter 9
Surround sound and other settings
Using the System Setup menu
All the available settings in the setup menu are
listed in Surround and sound setup options and
SR+ control options for Pioneer plasma displays
below. See the notes in each section for
additional information about the settings.
Follow the steps below to customize the
settings in the System Setup menu.
5 When you’re done, press ENTER to
leave the System Setup menu.
• The System Setup menu is exited
automatically after 5 minutes of inactivity.
• You can’t make these settings with the
Recording Mode (page 72) switched on.
Surround and sound setup options
SYSTEM SETUP
ENTER
The Room Setup feature (page 27) is designed
to give you a basic surround sound setup,
however you can make more detailed settings
that may improve the surround sound in your
listening room. Note that the first setting in
each section is the default.
Front speakers distance setting
Specifies the distance from your listening
position to the front speakers:
SHIFT
1 Press SYSTEM SETUP (SHIFT + HOME
MENU).
2 Use the / (cursor left/right) buttons
to choose the setting you want to adjust.
The current setting is shown for each option as
you cycle through the display. See below for a
full list and description of each.
3 Use the / (cursor up/down) buttons
to adjust the setting.
4 Repeat steps 2 and 3 to make other
settings.
• Front 1 ft. ~ Front 30 ft. – Distance can
be set in increments of 1 ft. The default is
10 ft.
Center speaker distance setting
Specifies the distance from your listening
position to the center speaker:
• Center 1 ft. ~ Center 30 ft. – Distance
can be set in increments of 1 ft. The default
is 10 ft.
Surround speakers distance setting
Specifies the distance from your listening
position to the surround speakers:
• Surr. 1 ft. ~ Surr. 30 ft. – Distance can be
set in increments of 1 ft. The default is 10 ft.
58
En
XV-HTD340.book 59 ページ 2003年12月27日 土曜日 午前10時30分
Surround sound and other settings
Dynamic Range Control
LFE attenuator setting
Specifies the amount of dynamic range
adjustment to Dolby Digital or DTS
soundtracks:
Dolby Digital and DTS audio sources include
ultra-low bass tones. Set the LFE attenuator as
needed to prevent the ultra-low bass from
distorting the sound.
• DRC Off – No dynamic range adjustment
(use when listening at higher volume)
• DRC Mid. – Mid setting
• DRC High – Dynamic range is reduced
(loud sounds are reduced in volume while
quieter sounds are increased)
• This setting works only with Dolby Digital
and some DTS soundtracks. For other
sources you can create a similar effect
using the Midnight mode (see Using Quiet
and Midnight listening modes on page 41).
Dual mono setting
Specifies how dual mono encoded Dolby
Digital or DTS soundtracks should be played.
You can also use this setting to switch the
audio channel on DVD-RW discs recorded with
two separate soundtracks.
• L-Ch1 R-Ch2 – Both channels are played
through the front speakers
• Ch1 Mono – Only channel 1 is played
• Ch2 Mono – Only channel 2 is played
09
• LFE ATT 0 – The LFE channel is played with
no attenuation
• LFE ATT 10 – LFE channel is attenuated by
10dB
• LFE Off – LFE channel is not played
SR+ control options for Pioneer
plasma displays
Make the following settings if you have
connected a Pioneer plasma display to this
unit using an SR+ cable (not supplied).
Note that in the function settings below, the
number of video inputs may change depending
on your display. See also Using this unit with a
Pioneer plasma display on page 16.
Control mode setting
• SR+ Off – Switches SR+ off (this unit and
the plasma display work independently)
• SR+ On – Switches SR+ on (this unit
sends control signals to the plasma
display)
The following settings are only available if the
Control mode setting (above) is switched on.
Volume control setting
• On the Ch1 Mono and Ch2 Mono settings
the sound comes only from the center
speaker (or from the front speakers if
listening in STEREO mode).
• This setting works only with dual mono
encoded Dolby Digital or DTS soundtracks.
See the disc packaging for channel
information.
• Vol C.Off – This unit does not control the
volume of the plasma display
• Vol C.On – When this unit is switched to
an input that used the plasma display
(DVD, for example), the volume on the
plasma display is muted so only sound
from this unit is heard.
59
En
XV-HTD340.book 60 ページ 2003年12月27日 土曜日 午前10時30分
09
Surround sound and other settings
Function setting for DVD input
• DVD -> OFF/PDP1–5/PDPTV – Matches
the DVD function of this unit with a
numbered video input on the plasma
display. For example, DVD -> PDP2
matches the DVD input with video input 2
on the plasma display.
Function setting for TV input
• TV -> OFF/PDP1–5/PDPTV – Matches the
TV function of this unit with a numbered
video input on the plasma display. For
example, TV -> PDP1 matches the TV
input with video input 1 on the plasma
display.
Setting the channel levels
You can set the relative channel levels from
your main listening position for all of the
listening modes independently (except
STEREO).
If you used the Room Setup feature (page 27),
the channel levels for each listening mode will
already be set. However, you can still fine-tune
the levels here if you need to.
SURROUND
ADVANCED
VOLUME
Function setting for L1 input
• LINE1 -> OFF/PDP1–5/PDPTV – Matches
the LINE (L1) function of this unit with a
numbered video input on the plasma
display. For example, LINE1 -> PDP3
matches the LINE1 input with video input 3
on the plasma display.
ENTER
TEST TONE CH LEVEL
Function setting for L2 input
• LINE2 -> OFF/PDP1–5/PDPTV – Matches
the LINE (L2) function of this unit with a
numbered video input on the plasma
display. For example, LINE2 -> PDP3
matches the LINE2 input with video input 3
on the plasma display.
SHIFT
1 Select a listening mode.
Press SURROUND, ADVANCED or FRONT
SURROUND repeatedly to select the listening
mode you want.
2 Press TEST TONE (SHIFT + 4) to hear the
test tone.
The test tone is output in the following order
(from the speakers active in the current
listening mode):
• L – Front left speaker
• C – Center speaker
• R – Front right speaker
• RS – Right surround speaker
60
En
XV-HTD340.book 61 ページ 2003年12月27日 土曜日 午前10時30分
Surround sound and other settings
09
• LS – Left surround speaker
• SW – Subwoofer
3 Use the VOLUME +/– button to adjust
the volume to an appropriate level.
Turn down the volume to -40dB or less to
ensure you have adequate headroom.
4 Use the / (cursor up/down) buttons
to adjust the speaker levels in turn.
You should hear the test tone at the same
volume from each speaker when seated in the
main listening position. The channel level
range is ± 10 dB.
5 When you’re done, press ENTER to exit
test tone setup.
• The speaker volume can be adjusted while
listening to any sound source you want by
pressing CH LEVEL (SHIFT + 5) and then
using the / (cursor up/down) buttons
to adjust the channel levels. After you’re
finished with one channel, use the /
(cursor left/right) buttons to move to the
next.
• When the AUTO listening mode is
selected, using the test tone method will
adjust levels for multichannel sources
only. Use CH LEVEL (SHIFT + 5) and the
/ (cursor up/down) buttons (see tip
above) to set levels for the AUTO listening
mode with two channel sources.
• Since the subwoofer produces ultra-low
frequencies its sound may seem quieter
than it actually is.
61
En
XV-HTD340.book 62 ページ 2003年12月27日 土曜日 午前10時30分
10
Video Adjust menu
Chapter 10
Video Adjust menu
Video Adjust
• Default setting: Standard
2 Press (cursor down) to select
‘Detailed Settings’ then press ENTER.
From the Video Adjust screen you can select
the standard video presentation or define
presets of your own.
1 Press HOME MENU and select ‘Video
Adjust’ from the on-screen display.
Video Adjust
Video Adjust
Memory1
Detailed Settings
3
Adjust the picture quality settings.
Memory1
Recall Settings
2 Use the / (cursor left/right) buttons
to select a preset.
Memory1
Contrast
min
max
Brightness
min
min
max
max
Chroma Level
Video Adjust
Standard
• Use the / (cursor up/down) buttons to
select a setting.
• Standard
• Memory1–2 – Use for saving your own
presets (see below)
3 Press ENTER to make the setting and
exit the Video Adjust screen.
• Use the / (cursor left/right) buttons to
adjust the current setting.
• Press DISPLAY (SHIFT + 8) to switch
between full and single view.
• You can switch between preset numbers in
the Recall Settings menu item.
You can adjust any or all of the following
picture quality settings:
• Depending on the disc and the TV/monitor,
you may not see the effect clearly.
Creating your own presets
You can create up to two presets of your own.
1 Select one of the Memory presets (see
above).
62
En
• Contrast – Adjusts the contrast between
light and dark.
• Brightness – Adjusts the overall
brightness.
• Chroma Level – Adjusts how saturated
colors appear.
4 Press ENTER to save the preset and exit
the Video Adjust screen.
XV-HTD340.book 63 ページ 2003年12月27日 土曜日 午前10時30分
Initial Settings menu
11
Chapter 11
Initial Settings menu
Using the Initial Settings menu
The Initial Settings menu gives you complete
control in setting up your DVD system,
including video output settings and parental
lock settings, among others.
If an option is grayed out it means that it
cannot be changed at the current time. This is
usually because a disc is playing. Stop the
disc, then change the setting.
1 Press HOME MENU and select ‘Initial
Settings’ from the on-screen display.
Initial Settings
2 Use the cursor buttons and ENTER to
select the setting and option you want to
set.
All the settings and options are explained on
the following pages.
• In the table below, the default setting is
shown in bold: other settings are shown in
italics.
• Some settings, such as TV Screen, Audio
Language and Subtitle Language may be
overridden by the DVD disc. Often these
settings can also be made from the DVD
disc menu.
Video Output settings
Setting
Option
What it means
TV Screen
4:3 (Letter Box)
(See also Screen sizes
and disc formats on
page 77.)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with black bars top and bottom.
4:3 (Pan & Scan)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with the sides cropped so that the image fills the screen.
16:9 (Wide)
Set if you have a widescreen TV.
Interlace
Set if your TV is not compatible with progressive scan video.
Progressive
Set if your TV is compatible with progressive scan video (see
your TV’s instruction manual for details). Press ENTER once
more to confirm (or RETURN to cancel).
Note that progressive scan video is only output from the
component video jacks and that there is no output from the
composite and S-video jacks when this setting is selected.
Component Out
(See also Connecting
using the component
video output on
page 14.)
63
En
XV-HTD340.book 64 ページ 2003年12月27日 土曜日 午前10時30分
11
Initial Settings menu
Setting
Option
What it means
S-Video Out
S2
Standard setting.
(See also Connecting
using the S-video output S1
on page 14.)
If you find that the picture is stretched or distorted on the
default S2 setting, try changing it to this setting.
Language settings
Setting
Option
What it means
Audio Language
English
If there is an English soundtrack on the disc then it will be
played.
Languages as displayed If there is the language selected on the disc, then it will be
played.
Subtitle Language
Other Language
Select to choose a language other than the ones displayed (see
Selecting languages using the language code list on page 77).
English
If there is are English subtitles on the disc then they will be
displayed.
Languages as displayed If there is the subtitle language selected on the disc, then it will
be displayed.
DVD Menu Language
Other Language
Select to choose a language other than the ones displayed (see
Selecting languages using the language code list on page 77).
w/Subtitle Lang.
DVD disc menus will be displayed in the same language as
your selected subtitle language, if possible.
Languages as displayed DVD disc menus will be displayed in the selected language, if
possible.
Subtitle Display
Other Language
Select to choose a language other than the ones displayed (see
Selecting languages using the language code list on page 77).
On
Subtitles are displayed according to your selected subtitle
language (see above).
Off
Subtitles are always off by default when you play a DVD disc
(note that some discs override this setting).
Display settings
Setting
Option
What it means
OSD Language
English
On-screen displays of the player are in English.
Languages as displayed On-screen displays are shown in the language selected.
64
En
XV-HTD340.book 65 ページ 2003年12月27日 土曜日 午前10時30分
Initial Settings menu
11
Setting
Option
What it means
On Screen Display
On
Operation displays (Play, Resume, Scan, and so on) are
shown on-screen.
Off
Operation displays are not shown.
On
A camera icon is displayed on-screen during multi-angle
scenes on a DVD disc.
Off
No multi-angle indication is shown.
Setting
Option
What it means
Parental Lock
See below
See Parental Lock below.
Photo Viewer
On
Only the JPEG files are shown on discs that contains both
WMA/MP3 audio files and JPEG picture files.
Off
WMA/MP3 audio file playback is possible.
Angle Indicator
Options
Parental Lock
• Default level: Off; Default password: none;
Default Country code: us (2119)
To give you some control over what your
children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If
your player is set to a lower level than the disc,
the disc won’t play.
Some discs also support the Country Code
feature. The player does not play certain
scenes on these discs, depending on the
Country Code you set.
• Not all discs use Parental Lock, and will
play without requiring the password first.
• If you forget your password, you’ll need to
reset the player to register a new password.
(see Resetting the system on page 68)
Registering a new password
You must register a password before you can
change the Parental Lock level or enter a
Country code.
1
Select ‘Password’.
Initial Settings
Video Output
Language
Display
Options
Parental Lock
PhotoViewer
Password
Level Change
Country Code
2 Use the number buttons to enter a 4digit password.
The numbers you enter show up as asterisks
(*) on-screen.
3 Press ENTER to register the password.
You will return to the Options menu screen.
65
En
XV-HTD340.book 66 ページ 2003年12月27日 土曜日 午前10時30分
11
Initial Settings menu
Changing your password
To change your password, confirm your
existing password then enter a new one.
1
Select ‘Password Change’.
2 Use the number buttons to enter your
existing password, then press ENTER.
3 Enter a new password and press ENTER.
This registers the new password and you will
return to the Options menu screen.
Setting/changing the Parental Lock
1
Select ‘Level Change’.
2 Use number buttons to enter your
password, then press ENTER.
3
Select a new level and press ENTER.
• Press (cursor left) repeatedly to lock
more levels (more discs will require the
password); press (cursor right) to
unlock levels. You can’t lock level 1.
This sets the new level and you will return to the
Options menu screen.
Setting/changing the Country code
You can find the Country code list on page 78.
1
Select ‘Country Code’.
2 Use number buttons to enter your
password, then press ENTER.
3 Select a Country code and press ENTER.
There are two ways you can do this:
• Select by code letter: Use / (cursor up/
down) to change the Country code.
• Select by code number: Press (cursor
right) then use the number buttons to enter
the 4-digit Country code.
66
En
• The new Country code is set and you will
return to the Options menu screen. Note
that the new Country code doesn’t take
effect until the next disc is loaded (or the
current disc is reloaded).
XV-HTD340.book 67 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
12
Chapter 12
Additional information
Optional system settings
System Setup menu options in standby
These settings are accessed by using the
System Setup menu while in standby.
Below are all the available settings in the setup
menu. The first setting in each section is the
default. See also the notes in each section for
additional information about the settings.
SYSTEM SETUP
Child lock setting
ENTER
The Child Lock feature is useful when you’ve
set the wake-up timer and don’t want the
system switched on before it activates.
• Lock On – Makes the front panel buttons
and controls inoperative.
• Lock Off – Restores regular use of the
front panel buttons and controls.
Clock format setting
SHIFT
Specifies how the clock is displayed:
Switch the system into standby.
• 12-Hour – Sets the clock to show in 12hour format in the display.
2 Press SYSTEM SETUP (SHIFT + HOME
MENU).
• 24-Hour – Sets the clock to show in 24hour format in the display.
1
3 Use the / (cursor left/right) buttons
to choose the setting you want to adjust
then press ENTER.
The current setting is shown for each option as
you cycle through the display. See below for a
full list and description of each.
4 Use the / (cursor up/down) buttons
to adjust the setting.
5 Repeat steps 2 and 3 to make other
settings.
6
Press ENTER to confirm.
TV attenuator setting
If the source connected to the TV analog input
is producing distortion through the speakers,
the attenuator will reduce the signal level.
• ATT 6dB – Reduces the signal level by 6dB.
• ATT 10dB – Reduces the signal level by
10dB.
• ATT Off – No attenuation
Line attenuator setting
If the source connected to the LINE analog
input is distorting, the attenuator can reduce
the signal level.
• ATT 6dB – Reduces the signal level by 6dB.
67
En
XV-HTD340.book 68 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
• ATT 10dB – Reduces the signal level by
10dB.
• ATT Off – No attenuation
Frequency step setting
If you find that you can’t tune into stations
successfully, the frequency step may not be
suitable for your country/region.
Using and taking care of discs
Titles, chapters and tracks
DVD discs are generally divided into one or
more titles. Titles may be further subdivided
into chapters.
• FM 50. AM 9
• FM 100. AM 10
Title 1
Title 2
Title 3
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 1 Chapter 2
System demo setting
Switches the automatic demo feature on or off
(this starts when the system is plugged in for
the first time):
CDs and Video CDs are divided into tracks.
• Demo On – Switches the demo feature on.
Use this procedure to reset all system settings
to the factory default.
1
Switch the system into standby.
2 Press and hold the front panel (stop)
button for about 8 seconds until the
display shows ‘Mem.Clr.?’.
3 Press the front panel button.
All the system’s settings are now reset, and
you should see the ‘Let’s Get Started’ screen.
68
En
Track 3 Track 4
Track 5
Track 6
Folder A
Track 2
Track 3
Folder B
Folder C
Track 1
File 1
.jpg
.jpg
.mp3
.mp3
CD-ROMs contain folders and files. WMA/MP3
files are referred to as tracks. Folders may
contain further folders.
Track 1
Resetting the system
Track 2
.mp3
• After setting the clock, the demo mode
switches off automatically. However, if you
unplug the system from the wall outlet, the
demo mode will revert to Demo On (and
the clock will be reset).
Track 1
.mp3
• Demo Off – Switches the demo feature off.
File 2
DVD Video regions
All DVD Video discs carry a region mark on the
case somewhere that indicates which
region(s) of the world the disc is compatible
with. Your DVD system also has a region mark,
which you can find on the rear panel. Discs
from incompatible regions will not play in this
system. Discs marked ALL will play in any
system.
XV-HTD340.book 69 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
The diagram below shows the various DVD
regions of the world.
12
If necessary, use a cloth soaked in alcohol, or a
commercially available CD/DVD cleaning kit to
clean a disc more thoroughly. Never use
benzine, thinner or other cleaning agents,
including products designed for cleaning vinyl
records.
Storing discs
Handling discs
When holding discs of any type, take care not
to leave fingerprints, dirt or scratches on the
disc surface. Hold the disc by its edge or by the
center hole and edge.
Damaged or dirty discs can affect playback
performance. Take care also not to scratch the
label side of the disc. Although not as fragile as
the recorded side, scratches can still result in
a disc becoming unusable.
Should a disc become marked with
fingerprints, dust, etc., clean using a soft, dry
cloth, wiping the disc lightly from the center to
the outside edge as shown in the diagram
below.
Although CDs and DVD discs are more durable
than vinyl records, you should still take care to
handle and store discs correctly. When you're
not using a disc, return it to its case and store
upright. Avoid leaving discs in excessively cold,
humid, or hot environments (including under
direct sunlight).
Don't glue paper or put stickers onto the disc,
or use a pencil, ball-point pen or other sharptipped writing instrument. These could all
damage the disc.
For more detailed care information see the
instructions that come with discs.
Do not load more than one disc into the player
at a time.
Discs to avoid
Wipe lightly from the center of the disc using
straight strokes.
Discs spin at high speed inside the player. If
you can see that a disc is cracked, chipped,
warped, or otherwise damaged, don't risk
using it—you could end up damaging the
player.
Don’t wipe the disc surface using circular
strokes.
69
En
XV-HTD340.book 70 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
This system is designed for use with
conventional, fully circular discs only. Use of
shaped discs is not recommended for this
product. Pioneer disclaims all liability arising
in connection with the use of shaped discs.
Proper installation and
maintenance of this system
Hints on installation
We want you to enjoy using this system for
years to come, so please bear in mind the
following points when choosing a suitable
location for it:
Do...
Use in a well-ventilated room.
Place on a solid, flat, level surface, such as
a table, shelf or stereo rack.
Don’t...
Use in a place exposed to high
temperatures or humidity, including near
radiators and other heat-generating
appliances.
Place on a window sill or other place where
the system will be exposed to direct
sunlight.
Use in an excessively dusty or damp
environment.
Place directly on top of an amplifier, or
other component in your stereo system
that becomes hot in use.
Use near a television or monitor as you may
experience interference—especially if the
television uses an indoor antenna.
Use in a kitchen or other room where the
system may be exposed to smoke or steam.
Use on a thick rug or carpet, or cover with
cloth—this may prevent proper cooling of
the system unit.
70
En
Place on an unstable surface, or one that is
not large enough to support all four of the
system unit’s feet.
Cleaning the pickup lens
The DVD player’s lens should not become dirty
in normal use, but if for some reason it should
malfunction due to dust or dirt, consult your
nearest Pioneer authorized service center.
Although lens cleaners are commercially
available, we do not recommend using them
since some may damage the lens.
Problems with condensation
Condensation may form inside the system unit
if it is brought into a warm room from outside,
or if the temperature of the room rises quickly.
Although the condensation won’t damage the
system, it may temporarily impair its
performance. For this reason you should leave
it to adjust to the warmer temperature for
about an hour before switching on and using.
Moving the system unit
If you need to move the main unit, first remove
all discs, then press STANDBY/ON on the
front panel to turn the system off. Wait for
Good Bye to disappear from the display, then
unplug the power cord. Never lift or move the
system during playback—discs rotate at a high
speed and may be damaged.
• Unplugging the system before Good Bye
disappears from the display may cause the
system to return to the factory settings.
Power cord caution
Handle the power cord by the plug part. Do not
pull out the plug by tugging the cord, and never
touch the power cord when your hands are
wet, as this could cause a short circuit or
XV-HTD340.book 71 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
electric shock. Do not place the system unit, a
piece of furniture, or other object on the power
cord or pinch the cord in any other way. Never
make a knot in the cord or tie it with other
cords. The power cord should be routed so that
they are not likely to be stepped on. A damaged
power cord can cause a fire or give you an
electric shock. Check the power cord once in a
while. If you find it damaged, ask your nearest
Pioneer authorized service center or your
dealer for a replacement.
12
Connecting auxiliary components
This system has both stereo analog inputs and
outputs, as well as a coaxial digital input. Use
these to connect external components, such
as your VCR, MD or CD-R recorder.
Tape deck, etc.
AUDIO
INPUT
AUDIO
OUTPUT
Connecting external antennas
External AM antenna
Use 5–6 meters (15–18 feet) of vinyl-insulated
wire and set up either indoors or outdoors.
Leave the AM loop antenna connected.
ANTENNA
AUDIO
IN
AM LOOP
ANTENNA
IN
COAXIAL IN
Outdoor antenna
L
LINE 2
Indoor
antenna
(vinyl-coated
wire)
OUT
L
R
R
LINE 1
FM
UNBAL
75
TV
ANTENNA
AM LOOP
ANTENNA
15–18 ft. / 5–6m
FM
UNBAL
75
External FM antenna
Use 75Ω coaxial cable to hook up an external
FM antenna.
75Ω coaxial cable
ANTENNA
AM LOOP
ANTENNA
FM
UNBAL
75
• Connect the LINE 1 (IN) jacks to the
analog outputs of an external playback
component.
These include components such as a VCR or
cassette deck. Connect using RCA pin-plug
stereo cables.
• Connect the LINE 1 (OUT) jacks to the
analog inputs of an external recording
component.
These include components such as a cassette
deck, VCR, MD or another recorder with analog
inputs. Connect using RCA pin-plug stereo
cables.
• Connect the COAX IN (LINE 2) jack on
the rear panel to the coaxial digital output
of an external playback component.
COA
XIA
L IN
LIN
E2
71
En
XV-HTD340.book 72 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
These include digital components such as an
MD player, digital satellite, or a game system.
Connect using a coaxial digital cable (not
supplied).
• If you find that the LINE 1 audio is
distorting when played through this
system, you can set the input attenuator to
reduce the input signal level. See Optional
system settings on page 67 to do this.
Recording mode
The Recording mode allows you to make
surround-compatible analog recordings from
the LINE 1 (OUT) jacks. Dolby multichannel
sources will be downmixed to stereo for
improved playback with systems that can
provide matrix-decoding (like Dolby ProLogic).
1
Press SOUND MODE.
2 Use the Use the / (cursor left/right)
buttons to select ‘Rec Mode?’.
3
Press ENTER.
4 Use the / (cursor up/down) buttons
to select ‘R.Mode On’ or ‘R.Mode Off’.
• R.Mode On – A surround-compatible
downmix (left-total/right-total, or Lt/Rt) of
Dolby multichannel sources is output,
(suitable for Dolby Surround Pro Logic or
other matrix decoding).
• R.Mode Off – A simple stereo downmix
(left-only/right-only, or Lo/Ro) is output
(suitable for playback on a two-channel
stereo system or on headphones).
72
En
• When Recording mode is on, most
surround sound-related functions cannot
be used. The display will briefly blink
RecMode On if you try and use a
prohibited function while Recording mode
is on.
• When Recording mode is off, the audio
from the analog output may be interrupted,
depending on the operation.
• The Recording mode automatically
switches off if you change the input
function (DVD/CD, TUNER, etc.) or switch
the power off.
XV-HTD340.book 73 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
12
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
• If the system is not operating normally due to external effects such as static electricity,
disconnect the power plug from the outlet and insert again to resume normal operation.
General
Problem
Remedy
The power does not turn
on.
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the rear
panel. This could cause the system to shut off automatically.
No sound is output when
a function is selected.
• If you’re using the line input, make sure the component is connected
correctly (see Connecting auxiliary components on page 71).
• Press MUTE on the remote control to turn muting off.
• Adjust the VOLUME.
No image is output when
playing discs.
• Make sure the TV is connected correctly (see Connecting to your TV on
page 13).
• Reset the video output to interlace (see Watching progressive scan video
from the component video outputs on page 15).
No sound from surround
or center speakers.
• Refer to Setting the channel levels on page 60 to check speaker levels.
• Check that you haven’t selected the STEREO sound mode (see Listening
in stereo on page 40).
• Make sure the speakers are connected properly (see Connecting the
speakers on page 10).
Can’t operate the remote
control.
• Replace the batteries (see Putting the batteries in the remote control on
page 7).
• Operate within 23 ft. / 7 m, 30° of the remote sensor on the front panel
(see Using the remote control on page 8).
• Remove any obstacles or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
• You won’t be able to use the remote sensor of this unit with the
CONTROL IN jack of this unit connected to the CONTROL OUT jack of
your plasma display. You can use the remote sensor of the plasma display
(even in standby) as long as the power isn’t switched off.
73
En
XV-HTD340.book 74 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
Problem
Remedy
Sound Demo shows in
the display and the unit
can’t be controlled.
• Press and hold (stop) on the front panel for about five seconds. The
disc tray ejects automatically to indicate the Sound Demo mode is
disabled.
Timer indicator is blinking • Unplug the system, then plug back in. Wait for one minute then switch
and the system will not
on.
switch on.
• Make sure the fan at the rear of the system unit is not being blocked.
• Check that the speakers are connected correctly.
• Make sure the voltage of the mains power source is correct for the
model.
• If the problem persists, take it to your nearest Pioneer
authorized service center or your dealer for servicing.
DVD/CD/Video CD player
Problem
Remedy
The disc is ejected
automatically after
loading.
• Clean the disc.
• Align the disc properly in the disc guide.
• If the region number on a DVD-video disc does not match the number
on the system unit, the disc cannot be used (see DVD Video regions on
page 68).
• Allow time for any condensation inside the system unit to evaporate.
Avoid using the system near an air-conditioning unit.
Playback is not possible.
• If the disc is loaded upside down, reload the disc with the label side face
up.
Picture playback stops
• Press (stop), then (play) to start playback again.
and the operation buttons • Switch the power off once, then on again using the front panel
cannot be used.
STANDBY/ON button.
74
En
Settings are canceled.
• When the power is cut due to power failure or by unplugging the power
cord, settings will be canceled.
No picture/No color.
• Check that connections are correct and that plugs are inserted fully.
• Check the instruction manual of the TV/monitor to make sure the TV/
monitor settings are incorrect.
Screen is stretched or
aspect does not change.
• The TV Screen setting is incorrect. Set the TV Screen option to match
the TV/monitor you're using (see Video Output settings on page 63).
CD won’t play.
• Set the PhotoViewer menu option in the Initial Settings menu to Off to
be able to play some copy-protected CDs. See Options on page 65.
XV-HTD340.book 75 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
Problem
Remedy
When recorded on a VCR
or passed through an AV
selector, there is
disturbance in the
playback picture.
• This system uses copy-protection technology which may prevent
recording or cause picture problems when connected through a VCR or
AV selector. This is not a malfunction.
Picture disturbance
during playback or dark.
• This system is compatible with Macro-Vision System copy guard. Some
discs include a copy prevention signal, and when this type of disc is
played back, stripes etc., may appear on some sections of the picture
depending on the TV. This is not a malfunction.
• Discs respond differently to particular system functions. This may result
in the screen becoming black for a brief instant or shaking slightly when
the function is executed. These problems are largely due to differences
between discs and disc content and are not malfunctions of this system.
Noticeable difference in
DVD and CD volume.
• DVDs and CDs use different recording methods. This is not a
malfunction.
12
WMA/MP3/JPEG discs
Problem
Remedy
CD-ROM disc is not
• Make sure that the CD-ROM was recorded using the ISO 9660 disc
recognized by the system. format. See Disc / content format playback compatibility on page 8 for
other disc compatibility information.
Files don’t show up in the • The files on the disc must be named with the correct file extension:
Disc Navigator/Photo
.mp3 for MP3 files; .wma for WMA files; .jpg for JPEG files (upper or lowerBrowser.
case is OK). See Disc / content format playback compatibility on page 8 for
other disc compatibility information.
Can play JPEG files, but
not WMA/MP3 files on
the same disc (or vice
versa).
• Set the PhotoViewer menu option in the Initial Settings menu to Off to
be able to access the WMA/MP3 files. Set to On to be able to play the
JPEG files. See Options on page 65.
Can’t play WMA files.
• The files were recorded using DRM (digital rights management). This is
not a malfunction. See DRM in the Glossary on page 80.
Tuner
Problem
Remedy
Auto tuning does not pick • The radio signal is weak. Auto tuning will only detect radio stations with
up some stations.
a good signal. For more sensitive tuning, connect an outdoor antenna.
75
En
XV-HTD340.book 76 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
Problem
Remedy
Sound is mono only.
• Check that the tuner is not set to FM mono (see Improving poor FM
reception on page 35).
Considerable noise in
radio broadcasts.
• Tune into the correct frequency.
• Connect the antenna (see Connecting the supplied antennas on page 18
and Connecting external antennas on page 71).
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall.
• Connect an outdoor FM antenna (see Connecting external antennas on
page 71).
• Adjust the direction and position for best reception.
• Connect an additional internal or external AM antenna (see AM loop
antenna on page 18 and Connecting external antennas on page 71).
• Turn off any other equipment that may be causing the noise or move it
away from the system unit.
• The tuning interval is incorrect for your country or region. Try switching
the tuning interval (frequency step) (see TV attenuator setting on page 67).
Error Messages
76
En
Message
Description
Child Lock
• This message appears when the front panel buttons are pressed when
the child lock feature is active. See Child lock setting on page 67 for more
on switching on/off the child lock.
Rec Mode On
• Blinks rapidly for 2 seconds when an operation is prohibited because
the Recording Mode is on (see Recording mode on page 72).
Phones In
• Blinks rapidly for 2 seconds when an operation is prohibited because
headphones are connected.
96k Stereo
• Blinks rapidly for 2 seconds when an operation is prohibited because
the source is digital 88.2 or 96kHz PCM.
No Surr. SP
• Blinks rapidly for 2 seconds when an operation is prohibited because
there is no surround speaker output.
Muting
• Blinks rapidly for 2 seconds when an operation is prohibited because
the sound is muted (press the MUTE button to turn the sound on).
Exit
• Appears briefly when a menu is automatically exited after a set period of
inactivity.
SR+ Error
• Appears when there is a communication problem between the unit and
the plasma display. Check all connections and retry.
XV-HTD340.book 77 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
Screen sizes and disc formats
DVD-Video discs come in several different
screen aspects, ranging from TV programs,
which are generally 4:3, to CinemaScope
widescreen movies, with an aspect ratio of up
to about 7:3.
12
Set to 4:3 (Pan&Scan), widescreen discs are
shown with the left and right sides cropped.
Although the picture looks larger, you don’t
actually see the whole picture.
Televisions also come in different aspect
ratios; ‘standard’ 4:3 and widescreen 16:9.
Widescreen TV users
If you have a widescreen TV, the TV Screen
setting (page 63) of this system should be set
to 16:9 (Wide).
Please note that many widescreen discs
override the system’s settings so that the disc
is shown in letterbox format regardless of the
setting.
When you watch discs recorded in 4:3 format,
you can use the TV controls to select how the
picture is presented. Your TV may offer various
zoom and stretch options; see the instructions
that came with your TV for details.
Please note that some movie aspect ratios are
wider than 16:9, so even though you have a
widescreen TV, these discs will still play in a
‘letterbox’ style with black bars at the top and
bottom of the screen.
Standard TV users
If you have a standard TV, the TV Screen setting
(page 63) of this system should be set to 4:3
(Letter Box) or 4:3 (Pan&Scan), depending on
which you prefer.
Set to 4:3 (Letter Box), widescreen discs are
shown with black bars top and bottom.
• Using the 16:9 (Wide) setting with a
standard 4:3 TV, or either of the 4:3 settings
with a widescreen TV, will result in a
distorted picture.
Selecting languages using the
language code list
Some of the language options allow you to set
your preferred language from any of the 136
languages listed in the Language code list on
page 78.
1
Select ‘Other Language’.
2 Use the / (cursor left/right) buttons
to select either a code letter or a code
number.
3 Use the / (cursor up/down) buttons
to select a code letter or a code number.
See Language code list on page 78 for a
complete list of languages and codes.
77
En
XV-HTD340.book 78 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
Language code list
Language (Language code letter), Language code
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
German (de), 0405
Italian (it), 0920
Spanish (es), 0519
Dutch (nl), 1412
Russian (ru), 1821
Chinese (zh), 2608
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar), 0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh), 0208
Bislama (bi), 0209
Bengali (bn), 0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz), 0426
Esperanto (eo), 0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Panjabi (pa), 1601
Polish (pl), 1612
Pashto, Pushto (ps), 1619
Portuguese (pt), 1620
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swedish (sv), 1922
Swahili (sw), 1923
Tamil (ta), 2001
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Country code list
Country, Country code, Country code letter
Argentina, 0118, ar
Australia, 0121, au
Austria, 0120, at
Belgium, 0205, be
Brazil, 0218, br
Canada, 0301, ca
Chile, 0312, cl
China, 0314, cn
Denmark, 0411, dk
Finland, 0609, fi
France, 0618, fr
Germany, 0405, de
78
En
Hong Kong, 0811, hk
India, 0914, in
Indonesia, 0904, id
Italy, 0920, it
Japan, 1016, jp
Korea, Republic of, 1118, kr
Malaysia, 1325, my
Mexico, 1324, mx
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Philippines, 1608, ph
Portugal, 1620, pt
Russian Federation, 1821, ru
Singapore, 1907, sg
Spain, 0519, es
Switzerland, 0308, ch
Sweden, 1905, se
Taiwan, 2023, tw
Thailand, 2008, th
United Kingdom, 0702, gb
United States of America, 2119, us
XV-HTD340.book 79 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
12
Preset code list
Please note that there are cases where only certain functions may be controllable after assigning
the proper preset code, or the codes for the manufacturer in the list will not work for the model
that you are using.
ACURA 644
ADMIRAL 631
AIWA 660
AKAI 632, 635, 642
AKURA 641
ALBA 607, 639, 641, 644
AMSTRAD 642, 644, 647
ANITECH 644
ASA 645
ASUKA 641
AUDIOGONIC 607, 636
BASIC LINE 641, 644
BAUR 631, 607, 642
BEKO 638
BEON 607
BLAUPUNKT 631
BLUE SKY 641
BLUE STAR 618
BPL 618
BRANDT 636
BTC 641
BUSH 607, 641, 642, 644, 647,
656
CASCADE 644
CATHAY 607
CENTURION 607
CGB 642
CIMLINE 644
CLARIVOX 607
CLATRONIC 638
CONDOR 638
CONTEC 644
CROSLEY 632
CROWN 638, 644
CRYSTAL 642
CYBERTRON 641
DAEWOO 607, 644, 656
DAINICHI 641
DANSAI 607
DAYTON 644
DECCA 607, 648
DIXI 607, 644
DUMONT 653
ELIN 607
ELITE 641
ELTA 644
EMERSON 642
ERRES 607
FERGUSON 607, 636, 651
FINLANDIA 635, 643, 655
FINLUX 632, 607, 645, 648,
653, 654, 655
FIRSTLINE 640, 644
FISHER 632, 635, 638, 645
FORMENTI 632, 607, 642
FRONTECH 631, 642, 646
FRONTECH/PROTECH 632
FUJITSU 648, 629
FUNAI 640, 646, 658
GBC 632, 642
GE 601, 608, 607, 610, 617, 602,
628, 618
GEC 607, 634, 648
GELOSO 632, 644
GENEXXA 631, 641
GOLDSTAR 610, 623, 621, 602,
607, 650
GOODMANS 607, 639, 647, 648,
656
GORENJE 638
GPM 641
GRAETZ 631, 642
GRANADA 607, 635, 642, 643,
648
GRADIENTE 630, 657
GRANDIN 618
GRUNDIG 631, 653
HANSEATIC 607, 642
HCM 618, 644
HINARI 607, 641, 644
HISAWA 618
HITACHI 631, 633, 634, 636, 642,
643, 654, 606, 610, 624, 625, 618
HUANYU 656
HYPSON 607, 618, 646
ICE 646, 647
IMPERIAL 638, 642
INDIANA 607
INGELEN 631
INTERFUNK 631, 632, 607, 642
INTERVISION 646, 649
ISUKAI 641
ITC 642
ITT 631, 632, 642
JEC 605
JVC 613, 623
KAISUI 618, 641, 644
KAPSCH 631
KENDO 642
KENNEDY 632, 642
KORPEL 607
KOYODA 644
LEYCO 607, 640, 646, 648
LIESENK&TTER 607
LOEWE 607
LUXOR 632, 642, 643
M-ELECTRONIC 631, 644, 645,
654, 655, 656, 607, 636, 651
MAGNADYNE 632, 649
MAGNAFON 649
MAGNAVOX 607, 610, 603, 612,
629
MANESTH 639, 646
MARANTZ 607
MARK 607
MATSUI 607, 639, 640, 642, 644,
647, 648
MEDIATOR 607
MEMOREX 644
METZ 631
MINERVA 631, 653
MITSUBISHI 609, 610, 602, 621,
631
MULTITECH 644, 649
NEC 659
NECKERMANN 631, 607
NEI 607, 642
NIKKAI 605, 607, 641, 646, 648
NOBLIKO 649
NOKIA 632, 642, 652
NORDMENDE 632, 636, 651,
652
OCEANIC 631, 632, 642
ORION 632, 607, 639, 640
OSAKI 641, 646, 648
OSO 641
OSUME 648
OTTO VERSAND 631, 632, 607,
642
PALLADIUM 638
PANAMA 646
PANASONIC 631, 607, 608,642,
622
PATHO CINEMA 642
PAUSA 644
PHILCO 632, 642
PHILIPS 631, 607, 634, 656
PHOENIX 632
PHONOLA 607
PROFEX 642, 644
PROTECH 607, 642, 644, 646,
649
QUELLE 631, 632, 607, 642, 645,
653
R-LINE 607
RADIOLA 607
RADIOSHACK 610, 623, 621,
602
RBM 653
RCA 601, 610, 615, 616, 617, 618,
661, 662, 609
REDIFFUSION 632, 642
REX 631, 646
ROADSTAR 641, 644, 646
SABA 631, 636, 642, 651
SAISHO 639, 644, 646
SALORA 631, 632, 642, 643
SAMBERS 649
SAMSUNG 607, 638, 644, 646
SANYO 635, 645, 648, 621, 614
SBR 607, 634
SCHAUB LORENZ 642
SCHNEIDER 607, 641, 647
SEG 642, 646
MCMICHAEL 634
SEI 632, 640, 649
SELECO 631, 642
SHARP 602, 619, 627
SIAREM 632, 649
SIEMENS 631
SINUDYNE 632, 639, 640, 649
SKANTIC 643
SOLAVOX 631
SONOKO 607, 644
SONOLOR 631, 635
SONTEC 607
SONY 604
SOUNDWAVE 607
STANDARD 641, 644
STERN 631
SUSUMU 641
SYSLINE 607
TANDY 631, 641, 648
TASHIKO 634
TATUNG 607, 648
TEC 642
TELEAVIA 636
TELEFUNKEN 636, 637, 652
TELETECH 644
TENSAI 640, 641
THOMSON 636, 651, 652, 663
THORN 631, 607, 642, 645, 648
TOMASHI 618
TOSHIBA 605, 602, 626, 621, 653
TOWADA 642
ULTRAVOX 632, 642, 649
UNIVERSUM 631, 607, 638, 642,
645, 646, 654, 655
VESTEL 607
VICTOR 613
VOXSON 631
WALTHAM 643
WATSON 607
WATT RADIO 632, 642, 649
WHITE
WESTINGHOUSE 607
YOKO 607, 642, 646
ZENITH 603, 620
PIONEER 600, 631, 632, 607,
636, 642, 651
79
En
XV-HTD340.book 80 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
Glossary
Analog audio Direct representation of sound by an
electrical signal. See also Digital audio.
Aspect ratio
Dolby Digital A multichannel audio encoding
system developed by Dolby
Laboratories that enables far more
audio to be stored on a disc than PCM
encoding. See also PCM (Pulse Code
Modulation).
DRM (digital rights management) is a
technology designed to prevent
unauthorized copying by restricting
playback of material on devices other
than the PC used to record it. For
detailed information, please see the
instruction manuals or help files that
came with your PC and WMA
recording software.
DTS
A multichannel audio encoding
system developed by Digital Theater
Systems that enables far more audio
to be stored on a disc than PCM
encoding. See also PCM (Pulse Code
Modulation).
Dynamic
range
The difference between the quietest
and loudest sounds possible in an
audio signal.
A file format developed by Fuji Photo
EXIF
(Exchangeable Film for digital still cameras. Digital
cameras from various manufacturers
Image File)
use this compressed file format which
carries date, time and thumbnail
information, as well as the picture
data.
80
En
A standard file format used for still
images. JPEG files are identified by the
file extension “.jpg”.
MP3
MP3 (MPEG1 audio layer 3) is a
compressed stereo audio file format.
Files are recognized by their file
extension “.mp3”.
MPEG audio
An audio format used on Video CDs
and some DVD discs.
MPEG video
A video format used on Video CDs and
some DVD discs.
PBC
(PlayBack
Control)
A system of navigating a Video CD
through on-screen menus recorded
onto the disc.
PCM
(Pulse Code
Modulation)
Digital audio encoding system found
on CDs. Good quality, but requires a lot
of data compared to Dolby Digital, DTS
and MPEG encoded audio. See also
Digital audio.
Progressive
scan video
All the lines that make up a video
picture are updated in one pass
(compared to interlace which takes
two passes to update the whole
picture).
Regions
These associate DVD-Video discs and
players with particular areas of the
world. See DVD Video regions on
page 68 for more information.
Sampling
frequency
The rate at which sound is measured
to be turned into digital audio data.
The higher the rate, the better the
sound quality. CD is 44.1 kHz; DVD can
be up to 96 kHz. See also Digital audio.
WMA
WMA is short for Windows Media
Audio and refers to an audio
compression technology developed by
Microsoft Corporation. Files are
recognized by their file extension
“.wma”.
The width of a TV screen relative to its
height. Conventional TVs are 4:3;
widescreen models are 16:9.
Digital audio Indirect representation of sound using
numbers. See also Sampling frequency
and Analog audio.
DRM
JPEG
File
extension
A tag added to the end of a filename to
indicate the type of file. For example,
“.mp3” indicates an MP3 file.
Manufactured under license from Dolby
Laboratories.“Dolby”, “Pro Logic” and the doubleD symbol are trademarks of Dolby Laboratories.
ISO 9660
format
International standard for the volume
and file structure of CD-ROM discs.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
XV-HTD340.book 81 ページ 2003年12月27日 土曜日 午前10時30分
Additional information
Specifications
Amplifier section
Continuous Power Output (RMS):
Front, center, surround . . . . . .100 W per channel
(1 kHz, 10 % T.H.D., 6 Ω)
Subwoofer . . . . 100 W (100 Hz, 10 % T.H.D., 6 Ω)
12
Speakers
Woofer . . . . . . . . . . . . . . . . . . 10 cm cone type
Tweeter . . . . . . . . . . . . 3.2 cm semi-dome type
Nominal impedance. . . . . . . . . . . . . . . . . . . . . 6 Ω
Frequency range . . . . . . . . . . . . . 60 Hz to 20 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 100 W
Dimensions . . . . 155 (W) x 360 (H) x 177 (D) mm/
6 1/8 (W) x 14 3/16 (H) x 6 15/16 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . . .2.4 kg / 5 lb 5 oz
FM tuner section
Frequency range . . . . . . . . . . . . . . 87.5 – 108 MHz
Antenna . . . . . . . . . . . . . . . . . . .75 Ω, unbalanced
AM tuner section
Frequency range
With 9 kHz step . . . . . . . . . . 531 kHz to 1,602 kHz
With 10 kHz step . . . . . . . . . 530 kHz to 1,700 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Miscellaneous
Power requirements . . . . . . . . . . AC 120 V, 60 Hz
Power consumption . . . . . . . . . . . . . . . . . . 180 W
Power consumption in standby . . . . . . . . . . 0.5 W
Dimensions . . . .420 (W) x 126 (H) x 445 (D) mm/
16 9/16 (W) x 4 15/16 (H) x 17 1/2 (D) in.
Weight . . . . . . . . . . . . . . . . . . .9.8 kg / 21 lb. 10 oz
Accessories (DVD/CD receiver)
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . . .2
Video cable (yellow plugs) . . . . . . . . . . . . . . . . . .1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . .1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
These operating instructions . . . . . . . . . . . . . . . .1
Warranty Card . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Center speaker
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . .8.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . . 8.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . . 6 Ω
Frequency range . . . . . . . . . . . . . 65 Hz to 20 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 100 W
Dimensions . . . . . 350 (W) x 116 (H) x 98 (D) mm/
13 3/4 (W) x 4 9/16 (H) x 3 7/8 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . . .1.6 kg / 3 lb 8 oz
Surround speakers
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . .8.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . . 8.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . . 6 Ω
Frequency range . . . . . . . . . . . . . 85 Hz to 20 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 100 W
Dimensions . . . . . 155 (W) x 116 (H) x 98 (D) mm/
6 1/8 (W) x 4 9/16 (H) x 3 7/8 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . . . . 1 kg / 2 lb 3 oz
Speaker System (S-HTD340)
(Front speakers x2, surround speakers x2, center
speaker x1, subwoofer x1)
Front speakers
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . . 2-way system
81
En
XV-HTD340.book 82 ページ 2003年12月27日 土曜日 午前10時30分
12
Additional information
Subwoofer
Enclosure. . . . . . . . . . . . . . . Bass-reflex floor type
System . . . . . . . . . . . . . . . . . . 16 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . . 16 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . 6 Ω
Frequency range . . . . . . . . . . . . . . 35 Hz to 2 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 100 W
Dimensions . . . . 190 (W) x 360 (H) x 327 (D) mm/
7 1/2 (W) x 14 3/16 (H) x 12 7/8 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . 5.0 kg / 11 lb 0 oz
Accessories (Speaker system)
Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . 1 sheet
• This product includes FontAvenue® fonts
licensed by NEC corporation. FontAvenue
is a registered trademark of NEC
Corporation.
• Specifications and design subject to
possible modification without notice, due
to improvements.
82
En
XV-HTD340.book 83 ページ 2003年12月27日 土曜日 午前10時30分
XV-HTD340.book 84 ページ 2003年12月27日 土曜日 午前10時30分
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 656-472-1111
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002E
<04A000001>
Printed in
<XRB3031-A>