Airwell GC 30 DCI Service manual

SX DCI Series
Indoor Units
Outdoor Units
SX 9 DCI
GC 9 DCI
SX 12 DCI
GC 12 DCI
SX 18 DCI
GC 18 DCI
SX 24 DCI
GC 24 DCI
SX 30 DCI
GC 30 DCI
REFRIGERANT
R410A
SM SX DCI 1-A.3 GB
HEAT PUMP
AUGUST – 2008
CONTENT
LIST OF EFFECTIVE PAGES
LIST OF EFFECTIVE PAGES
Note: Changes in the pages are indicated by a “Revision#” in the footer of each effected page
(when none indicates no changes in the relevant page). All pages in the following list represent
effected/ non effected pages divided by chapters.
Dates of issue for original and changed pages are:
Original ....... 0 ........ April 2006
Total number of pages in this publication is 88 consisting of the following:
Page
No.
Revision
No. #
Page
No.
Revision
No. #
Page
No.
Revision
No. #
Title .......................3
A ...........................3
i .............................3
1-1 - 1-3 ................3
2-1 - 2-5 ................3
3-1 ........................3
4-1 - 4-2 ................3
5-1 - 5-24 ..............3
6-1 - 6-5 ................3
7-1 ........................3
8-1 - 8-3 ................3
9-1 ........................3
10-1 ......................3
11-1-11-7...............3
12-1-12-20 ............3
13-1-13-11 ............3
14-1 ......................3
•
Zero in this column indicates an original page.
*Due to constant improvements please note that the data on this service manual can be modified
with out notice.
**Photos are not contractual
A
CONTENT
SM SX DCI 1-A.3 GB
TABLE OF CONTENTS
Table of Contents
1.
INTRODUCTION ...................................................................................................1-1
2.
PRODUCT DATA SHEET ......................................................................................2-1
3.
RATING CONDITIONS ..........................................................................................3-1
4.
OUTLINE DIMENSIONS........................................................................................4-1
5.
PERFORMANCE DATA & PRESSURE CURVES ................................................5-1
6.
SOUND LEVEL CHARACTERISTICS ...................................................................6-1
7.
ELECTRICAL DATA ...............................................................................................7-1
8.
WIRING DIAGRAMS .............................................................................................8-1
9.
REFRIGERATION DIAGRAMS .............................................................................9-1
10. TUBING CONNECTIONS ......................................................................................10-1
11.
CONTROL SYSTEM ..............................................................................................11-1
12. TROUBLESHOOTING ...........................................................................................12-1
13. EXPLODED VIEWS AND SPARE PARTS LISTS ..................................................13-1
14. APPENDIX A..........................................................................................................14-1
SM SX DCI 1-A.3 GB
i
INTRODUCTION
1.
INTRODUCTION
1.1
General
The SX split ceiling mounted range comprise RC (heat pump) models, as follows:
● Heat Pump
1.2
SX 9, SX 12, SX 18, SX 24, SX 30.
Main Features
The SX series benefits from the most advanced technological innovations, namely:
● DC Inverter Technology R410A models.
● High COP.
● Low indoor and outdoor noise levels.
● Microprocessor control.
● Infrared remote control with LED.
● Easy access to the interconnecting tubing and wiring connections, main control
panel can slide out for service .
● Automatic treated air sweep (by definition in NPR).
● Fresh Air & Distribution treated air to adjacent room.
● Indoor centrifugal fan.
● Easy installation and service.
1.3
Indoor Unit
The indoor unit is a floor/ ceiling mounted, and can be easily fitted to many types of
residential and commercials applications.
It includes:
● Coil with hydrophilic aluminum fins.
● Motorized flaps (two step motors)
● Advanced electronic control box assembly (DCI storm)
● Mounting plate
1.4
Filtration
The SX series presents several types assembly (DCI storm).
● Easily accessible, and re-usable pre-filters (mesh).
SM SX DCI 1-A.3 GB
CONTENT
1-1
INTRODUCTION
1.5
Control
The microprocessor indoor controller, and an infrared remote control, supplied as
standard, providing complete operating function and programming. For further details
please refer to the Operation Manual, Appendix A.
1.6
Outdoor Unit
The SX outdoor units can be installed as floor or wall mounted units by using a wall
supporting bracket. The metal sheets are protected by anti- corrosion paint work
allowing long life resistance. All outdoor units are pre-charged. For further information
please refer to the Product Data Sheet, Chapter 2.
It includes :
● Compressor mounted in a soundproofed compartment :
Single Rotary – for SX 9 DCI and SX 12 DCI.
Scroll – for SX 18 DCI.
Twin Rotary – for SX 24 DCI and SX 30 DCI.
● Axial fan.
● Outdoor coil with hydrophilic louver fins for RC units.
● Outlet air fan grill.
● Service valves” flare” type connection.
● Interconnecting wiring terminal block.
1.7
Tubing Connections
Flare type interconnecting tubing to be produced on site.
For further details please refer to the Installation Manual, Chapter 10tttvv.
1.8
Accessories
RCW Wall Mounted Remove Control
The RCW remote control is mounted on the wall, and controls the unit either as an
infrared remote control or as a wired controller.The wired controller can control up to 10
indoor units with the same program settings and adjustment.
For further details please refer to the Technical Service Manual
1.9
Inbox Documentation
Each unit is supplied with its own installation and operation manuals.
1-2
CONTENT
SM SX DCI 1-A.3 GB
INTRODUCTION
1.10
Matching Table
1.10.1
R410A
INDOOR UNITS
OUTDOOR UNITS
MODEL
REFRIGER.
SX 9
SX 12
SX 18
GC 9-12-18
R410A
√
√
√
GC 24-30
R410A
SX 24
SX 30
√
√
The above table lists outdoor units and SX DCI indoor units which can be matched together.
In addition the listed outdoor units can be matched with other types of indoor units such as
cassettes and wall mounted.
For further information please refer to the relevant Service Manual.
SM SX DCI 1-A.3 GB
CONTENT
1-3
PRODUCT DATA SHEET
2.
PRODUCT DATA SHEET
2.1
SX 9 DCI R410A
Model Indoor Unit
SX 9 DCI
Model Outdoor Unit
GC 9 DCI
Installation Method of Pipe
Characteristics
Units
Btu/hr
kW
kW
W/W
Capacity (1)
OUTDOOR
INDOOR
Power input (1)
EER (Cooling) or COP(Heating) (1)
Energy efficiency class
Power supply
Rated current
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
Air flow (2)
External static pressure
Sound power level (3)
Sound pressure level (4)
Moisture removal
Condenstate drain tube I.D
Dimensions
Weight
Package dimensions
Package weight
Units per pallet
Units stacking
Refrigerant control
Compressor type,model
Fan type & quantity
Fan speeds
Air flow
Sound power level
Sound pressure level (4)
Dimensions
Weight
Package dimensions
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Refrigerant chargless distance
Additional charge per 1 meter
Connections between units
Operation control type
Heating elements (Option)
Others
(1)
(2)
(3)
(4)
V/Ph/Hz
A
A
A
H/M/L
H/M/L
Min-Max
H/M/L
H/M/L
RPM
m3/hr
Pa
dB(A)
dB(A)
l/hr
Mm
Mm
Kg
Mm
Kg
Units
Units
WxDxH
WxDxH
H/L
H/L
H/L
H/L
WxDxH
RPM
m3/hr
dB(A)
dB(A)
Mm
Kg
Mm
Kg
Units
Units
WxDxH
Liquid line
Suction line
Max.tubing length
Max.height difference
kg/m
g/m
In.(mm)
In.(mm)
m.
m.
Flared
Cooling
Heating
8530(4780~12280)
10920(5120~15350)
2.5(1.4-3.6)
3.2(1.5~4.5)
0.62(0.42-1.1)
0.93(0.4~1.6)
4.03
3.41
A
B
220-240V/Single/50Hz
2.7
4.1
10.5
35
Centrifugal x 2
760/670/500
400/350/300
0
50/49/47
39/37/35
1
16
820*190*630
21
890*280*710
25
14units per pallet
7 levels
EEV
Single Rotary,DC Inverter,Panasonic 5RS102XAB
Propeller(direct) x 1
830
1780
61
51
795*290*610
38
945*395*655
42
9
3 levels
R410A
1.10kg/7.5m
No Need
1/4"(6.35)
3/8"(9.53)
Max.20
Max.10
Remote control
kW
Rating conditions in accordance with ISO 5151 and ISO 13253 (for ducted units) and EN 14511.
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1 meter distance from unit.
SM SX DCI 1-A.3 GB
CONTENT
2-1
PRODUCT DATA SHEET
2.2
SX 12 DCI R410A
Model Indoor Unit
SX 12 DCI
Model Outdoor Unit
GC 12 DCI
Installation Method of Pipe
Characteristics
Flared
Capacity (1)
Power input
(1)
EER (Cooling) or COP(Heating) (1)
Energy efficiency class
Units
Cooling
Heating
Btu/hr
11940(5120~15010)
14330(5120~17060)
kW
3.5(1.5-4.4)
4.2(1.5~5.0)
kW
0.98(0.46-1.3)
1.31(0.35~1.58)
W/W
3.57
3.21
A
Power supply
V/Ph/Hz
Rated current
A
Starting current
A
Circuit breaker rating
A
INDOOR
Fan type & quantity
C
220-240V/Single/50Hz
4.3
5.7
10.5
35
Centrifugal x 2
Fan speeds
H/M/L
RPM
830/760/500
Air flow (2)
External static pressure
H/M/L
m3/hr
450/400/300
Min-Max
Pa
0
Sound power level (3)
H/M/L
dB(A)
56/53/51
Sound pressure level (4)
Moisture removal
H/M/L
dB(A)
45/41/38
l/hr
1.5
Condenstate drain tube I.D
Dimensions
Mm
16
WxDxH
Mm
820*190*630
Kg
22
WxDxH
Mm
890*280*710
Weight
Package dimensions
Package weight
kg
26
Units per pallet
units
14units per pallet
Units stacking
units
7 levels
Refrigerant control
EEV
Compressor type,model
Single Rotary,DC Inverter,Panasonic 5RS102XAB
OUTDOOR
Fan type & quantity
Propeller(direct) x 1
Fan speeds
H/L
RPM
830
Air flow
H/L
m3/hr
1780
Sound power level
H/L
dB(A)
62
Sound pressure level (4)
Dimensions
H/L
dB(A)
52
WxDxH
mm
795*290*610
Weight
Package dimensions
WxDxH
Packaged weight
kg
38.5
mm
945*395*655
kg
42.5
Units per pallet
Units
9
Stacking height
units
3 levels
kg/m
1.20kg/7.5m
Refrigerant type
R410A
Refrigerant chargless distance
Additional charge per 1 meter
Connections
between units
g/m
No Need
Liquid line
In.(mm)
1/4"(6.35)
Suction line
In.(mm)
3/8"(9.53)
m.
Max.20
Max.tubing length
Max.height
difference
m.
Operation control type
Heating elements (Option)
Others
(1)
(2)
(3)
(4)
Max.10
Remote control
kW
Rating conditions in accordance with ISO 5151 and ISO 13253 (for ducted units) and EN 14511.
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1 meter distance from unit.
2-2
CONTENT
SM SX DCI 1-A.3 GB
PRODUCT DATA SHEET
2.3
SX 18 DCI R410A
Model Indoor Unit
SX 18 DCI
Model Outdoor Unit
GC 18 DCI
Installation Method of Pipe
Characteristics
Flared
Capacity (1)
Power input (1)
EER (Cooling) or COP(Heating) (1)
Energy efficiency class
Units
Cooling
Heating
Btu/hr
17000(5120-20460)
20460(5120-24550)
kW
5.0(1.5-6.0)
5.8(1.5~7.2)
kW
1.65(0.5-2.1)
1.69(0.45-2.1)
W/W
3.03
3.43
B
B
Power supply
V/Ph/Hz
Rated current
A
Starting current
A
Circuit breaker rating
A
220-240V/Single/50Hz
7.2
35
INDOOR
Fan type & quantity
Centrifugal x 2
Fan speeds
H/M/L
RPM
1050/950/700
Air flow (2)
External static pressure
H/M/L
m3/hr
870/750/600
Min-Max
Pa
0
Sound power level (3)
H/M/L
dB(A)
65/60/56
Sound pressure level (4)
Moisture removal
H/M/L
dB(A)
51/48/45
Condenstate drain tube I.D
Dimensions
WxDxH
Weight
Package dimensions
WxDxH
l/hr
2
mm
16
mm
1200*190*630
kg
30
mm
1270*280*710
Package weight
kg
35
Units per pallet
units
7units per pallet
Units stacking
units
7 levels
Refrigerant control
EEV
Compressor type,model
Scroll compressor 5CS130XCC03
Fan type & quantity
Propeller(direct) x 1
Fan speeds
H/L
RPM
920
Air flow
H/L
m3/hr
2160
Sound power level
Sound pressure level
Dimensions
OUTDOOR
7.7
10.5
H/L
dB(A)
63
H/L
dB(A)
53
WxDxH
mm
795*290*610
(4)
Weight
Package dimensions
WxDxH
Packaged weight
kg
39
mm
945*395*655
kg
43
Units per pallet
Units
9
Stacking height
units
3 levels
kg/m
1.50kg/7.5m
Refrigerant type
R410A
Refrigerant chargless distance
Additional charge per 1 meter
Connections between
units
g/m
No Need
Liquid line
In.(mm)
1/4"(6.35)
Suction line
In.(mm)
1/2"(12.7)
Max.tubing length
m.
Max.30
Max.height difference
m.
Max.10
Operation control type
Heating elements (Option)
Remote control
kW
Others
(1)
(2)
(3)
(4)
Rating conditions in accordance with ISO 5151 and ISO 13253 (for ducted units) and EN 14511.
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1 meter distance from unit.
SM SX DCI 1-A.3 GB
CONTENT
2-3
PRODUCT DATA SHEET
2.4
SX 24 DCI R410A
Model Indoor Unit
SX 24 DCI
Model Outdoor Unit
GC 24 DCI
Installation Method of Pipe
Characteristics
H/M/L
H/M/L
Min-Max
H/M/L
RPM
m3/hr
Pa
dB(A)
Flared
Cooling
Heating
23200(5120~25590)
25910(5110-30000)
6.80(1.50-7.60)
7.60(1.60~8.60)
2.25(0.50-2.68)
2.05(05~2.30)
3.02
3.61
B
A
220-240V/Single/50Hz
10.1
9.6
15
45
Centrifugal x 2
1300/1200/1050
1020/930/760
0
67/64/60
H/M/L
dB(A)
56/53/49
l/hr
mm
2.5
16
mm
kg
mm
kg
units
units
1200x630x190
32
1270x710x280
36
7
7
Units
Btu/hr
kW
kW
W/W
Capacity (1)
Power input (1)
EER (Cooling) or COP(Heating)
Energy efficiency class
Power supply
Rated current
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
(1)
Air flow (2)
External static pressure
INDOOR
Sound power level (3)
Sound pressure level (4)
Moisture removal
Condenstate drain tube I.D
OUTDOOR
Dimensions
Weight
Package dimensions
Packaged weight
Units per pallet
Stacking height
WxHxD
WxHxD
Refrigerant control
Compressor type,model
Fan type & quantity
Fan speeds
Air flow
Sound power level
H/L
H/L
H/L
RPM
m3/hr
dB(A)
EEV
Two Rotary,Mitsubishi TNB220F
Propeller(direct) x 1
850
3600
66
Sound pressure level (4)
H/L
dB(A)
56
WxHxD
mm
kg
mm
kg
Units
units
950*340*835
65.5
1087x477x910
70
2
2 levels
R410A
2.4/7.5
No Need
3/8”(9.53)
5/8”(15.88)
Max.30
Max.15
Remote control
Dimensions
Weight
Package dimensions
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Refrigerant chargless distance
Additional charge per 1 meter
Connections between units
Operation control type
Heating elements (Option)
Others
(1)
(2)
(3)
(4)
V/Ph/Hz
A
A
A
WxHxD
Liquid line
Suction line
Max.tubing length
Max.height difference
kg/m
g/m
In.(mm)
In.(mm)
m.
m.
kW
Rating conditions in accordance with ISO 5151 and ISO 13253 (for ducted units) and EN 14511.
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1 meter distance from unit.
2-4
CONTENT
SM SX DCI 1-A.3 GB
PRODUCT DATA SHEET
2.5
SX 30 DCI R410A
Model Indoor Unit
SX 30 DCI
Model Outdoor Unit
GC 30 DCI
Installation Method of Pipe
Characteristics
Flared
Units
Cooling
Heating
Btu/hr
25570(6820-32390)
30000(5110-35800)
kW
7.5(1.6-8.6)
8.4(1.8-9.8)
Capacity (1)
(1)
OUTDOOR
INDOOR
Power input
EER (Cooling) or COP(Heating) (1)
Energy efficiency class
Power supply
Rated current
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
H/M/L
H/M/L
Air flow (2)
External static pressure
Min-Max
H/M/L
Sound power level (3)
H/M/L
Sound pressure level (4)
Moisture removal
Condenstate drain tube I.D
Dimensions
WxHxD
Weight
Package dimensions
WxHxD
Packaged weight
Units per pallet
Stacking height
Refrigerant control
Compressor type,model
Fan type & quantity
Fan speeds
H/L
Air flow
H/L
Sound power level
H/L
H/L
Sound pressure level (4)
Dimensions
WxHxD
Weight
Package dimensions
WxHxD
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Refrigerant chargless distance
Additional charge per 1 meter
Liquid line
Suction line
Connections between
units
Max.tubing length
Max.height difference
Operation control type
Heating elements (Option)
kW
W/W
V/Ph/Hz
A
A
A
RPM
m3/hr
Pa
dB(A)
dB(A)
l/hr
mm
mm
kg
mm
kg
units
units
RPM
m3/hr
dB(A)
dB(A)
mm
kg
mm
kg
Units
units
kg/m
g/m
In.(mm)
In.(mm)
m.
m.
2.49(0.5-3.1)
2.46(0.5-2.8)
3.01
3.41
B
B
220-240V/Single/50Hz
11.3
11.0
15
45
Centrifugal x 2
1300/1200/1050
1020/930/760
0
67/64/60
56/53/49
2.9
16
1200x630x190
32
1270x710x280
36
7
7
EEV
Two Rotary,Mitsubishi TNB220F
Propeller(direct) x 1
850
3600
66
56
950*340*835
66
1087x477x910
70
2
2 levels
R410A
2.75/7.5
No Need
3/8”(9.53)
5/8”(15.88)
Max.30
Max.15
Remote control
kW
Others
(1)
(2)
(3)
(4)
Rating conditions in accordance with ISO 5151 and ISO 13253 (for ducted units) and EN 14511.
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1 meter distance from unit.
SM SX DCI 1-A.3 GB
CONTENT
2-5
RATING CONDITIONS
3.
RATING CONDITIONS
Standard conditions in accordance with ISO 5151, ISO 13253 (for ducted units)
and EN 14511.
Cooling:
Indoor:
27oC DB 19oC WB
Outdoor: 35 oC DB
Heating:
Indoor:
20oC DB
Outdoor: 7oC DB 6oC WB
3.1
Operating Limits
R410A
Indoor
Cooling
Heating
Voltage
SM SX DCI 1-A.3 GB
Outdoor
Upper limit
32oC DB 23oC WB
46oC DB
Lower limit
21oC DB 15oC WB
-10oC DB
Upper limit
27oC DB
24oC DB 18oC WB
Lower limit
10oC DB
-15oC DB -16oC WB
1PH
198 – 264 V
3PH
N/A
CONTENT
3-1
OUTLINE DIMENSIONS
4.
OUTLINE DIMENSIONS
4.1
Indoor Unit: SX 9, 12 DCI
4.2
Indoor Unit: SX 18, 24, 30 DCI
SM SX DCI 1-A.3 GB
CONTENT
4-1
OUTLINE DIMENSIONS
4.3
Outdoor Unit: GC 9, 12, 18 DCI
4.4
Outdoor Unit: GC 24, 30 DCI
4-2
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.
PERFORMANCE DATA
5,1
SX 9 DCI
5.1.1
Cooling Capacity (kW) – Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB/WB TEMPERATURE [oC]
OU COIL
ENTERING AIR DB
TEMPERATURE
[oC]
DATA
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
-10 - 20
(protection range)
25
30
35
40
46
22/15
24/17
27/19
29/21
32/23
2.42
2.09
0.49
2.30
2.04
0.54
2.18
1.98
0.60
2.07
1.93
0.66
1.93
1.87
0.73
80 - 110 % of nominal
80 - 105 % of nominal
25 - 50 % of nominal
2.57
2.73
2.89
2.13
2.18
2.22
0.50
0.51
0.52
2.46
2.62
2.77
2.08
2.12
2.17
0.56
0.55
0.57
2.34
2.66
2.50
2.03
2.07
2.11
0.62
0.61
0.63
2.23
2.54
2.38
1.97
2.02
2.06
0.67
0.68
0.69
2.09
2.24
2.40
1.91
1.95
2.00
0.74
0.75
0.75
3.05
2.26
0.52
2.93
2.21
0.58
2.82
2.16
0.64
2.70
2.10
0.70
2.56
2.04
0.76
LEGEND
TC
SC
PI
WB
DB
ID
OU
5.1.2
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Cooling Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ratio
1.10
1.00
0.90
0.80
0.70
0.60
0.50
20
25
30
35
40
45
Outdoor Temperature [ºC]
SM SX DCI 1-A.3 GB
CONTENT
5-1
PERFORMANCE DATA & PRESSURE CURVES
5.1.3
Heating Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB TEMPERATURE [oC]
OU COIL
ENTERING
AIR DB/WB
TEMPERATURE
[oC]
-15/-16
-10/-12
-7/-8
-1/-2
2/1
7/6
10/9
15/12
15-24
(Protection Range)
DATA
15
20
25
TC
PI
TC
PI
TC
PI
TC
PI
TC
2.04
0.56
2.27
0.67
2.44
0.76
2.53
0.80
2.58
1.75
0.67
1.98
0.79
2.16
0.87
2.24
0.92
2.30
PI
0.83
1.89
0.61
2.12
0.73
2.30
0.82
2.38
0.86
2.44
0.89
TC
PI
TC
PI
TC
PI
TC
PI
3.34
0.87
3.53
0.93
3.71
0.98
3.20
0.93
3.06
0.99
3.24
1.04
3.43
1.09
0.94
3.38
0.98
3.57
1.03
85 - 105 % of nominal
80 - 120 % of nominal
LEGEND
TC
PI
WB
DB
ID
OU
5.1.4
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Heating Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ration
1.10
1.00
0.90
0.80
0.70
0.60
0.50
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [deg C]
5-2
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.1.5
Model: SX 9 DCI Cooling – Test Mode
Suction Pressure Vs.Outdoor Temp.
Suction Pressure [kPa]
1400
Indoor
DB/WB
1300
1200
1100
22/15
1000
24/17
900
27/19
800
29/21
700
32/23
600
500
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
Discharge Pressure [kPa]
Discharge Pressure Vs. Outdoor Temp.
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
SM SX DCI 1-A.3 GB
CONTENT
5-3
PERFORMANCE DATA & PRESSURE CURVES
5.1.6
Heating – Test Mode
Suction Pressure [kPa]
Suction Pressure Vs.Outdoor Temp.
1300
1200
1100
1000
900
800
700
600
500
400
300
200
-15
15
20
25
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
Discharge Pressure [kPa]
Discharge Pressure Vs. Outdoor Temp.
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
-15
Indoor DB
15
20
25
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
5-4
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.2
SX 12 DCI
5.2.1
Cooling Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB/WB TEMPERATURE [oC]
OU COIL
ENTERING AIR DB
TEMPERATURE [oC]
22/15
DATA
-10 - 20
(protection range)
25
30
35
40
46
24/17
27/19
29/21
32/23
TC
SC
PI
TC
SC
PI
TC
SC
3.38
2.65
0.77
3.22
2.58
PI
0.86
80 - 110 % of nominal
80 - 105 % of nominal
25 - 50 % of nominal
3.60
3.83
4.05
2.70
2.75
2.81
0.78
0.80
0.81
3.44
3.66
3.88
2.63
2.69
2.74
0.89
0.88
0.90
TC
3.06
3.28
3.50
3.72
SC
2.51
2.57
2.62
2.67
2.73
PI
0.95
0.97
0.98
0.99
1.01
TC
2.89
3.12
3.56
3.78
SC
PI
TC
SC
PI
2.45
1.04
2.70
2.37
1.15
2.50
1.06
2.92
2.42
1.16
3.34
2.55
1.07
3.14
2.47
1.18
2.61
1.08
3.36
2.53
1.19
2.66
1.10
3.58
2.58
1.21
4.27
2.86
0.83
4.11
2.79
0.92
3.94
LEGEND
TC
SC
PI
WB
DB
ID
OU
5.2.2
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factor
Cooling Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ratio
1.10
1.00
0.90
0.80
0.70
0.60
0.50
20
25
30
35
40
45
Outdoor Temperature [ºC]
SM SX DCI 1-A.3 GB
CONTENT
5-5
PERFORMANCE DATA & PRESSURE CURVES
5.2.3
Heating Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB TEMPERATURE [oC]
OU COIL
ENTERING
AIR DB/WB
TEMPERATURE
[oC]
-15/-16
-10/-12
-7/-8
-1/-2
2/1
7/6
10/9
15/12
15-24
(Protection Range)
DATA
15
20
25
TC
PI
TC
PI
TC
PI
TC
PI
TC
2.67
0.79
2.98
0.95
3.20
1.07
3.32
1.13
3.39
2.49
0.87
2.79
1.03
3.02
1.15
3.13
1.21
3.20
1.25
2.30
0.95
2.60
1.11
2.83
1.23
2.94
1.29
3.02
4.20
1.31
4.01
1.39
4.26
1.46
4.50
1.54
PI
1.17
TC
PI
TC
PI
TC
PI
TC
PI
4.39
1.23
4.63
1.30
4.87
1.38
1.33
4.44
1.38
4.68
1.46
85 - 105 % of nominal
80 - 120 % of nominal
LEGEND
TC
PI
WB
DB
ID
OU
5.2.4
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Heating Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ration
1.10
1.00
0.90
0.80
0.70
0.60
0.50
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [deg C]
5-6
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.2.5
Model: SX 12 DCI Cooling – Test Mode
Suction Pressure VS.Outdoor Temp.
Suction Pressure [kPa]
1400
Indoor
DB/WB
1300
22/15
1200
24/17
1100
27/19
1000
29/21
900
32/23
800
700
600
500
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
Discharge Pressure [kPa]
Discharge Pressure VS. Outdoor Temp.
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
SM SX DCI 1-A.3 GB
CONTENT
5-7
PERFORMANCE DATA & PRESSURE CURVES
5.2.6
Heating – Test Mode
Suction Pressure VS.Outdoor Temp.
1300
Suction Pressure [kPa]
1200
1100
1000
900
800
15
700
20
600
25
500
400
300
200
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
Discharge Pressure [kPa]
Discharge Pressure VS. Outdoor Temp.
4000
3750
3500
3250
3000
2750
Indoor DB
15
2500
2250
2000
1750
1500
1250
1000
-15
20
25
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
5-8
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
Capacity Correction Factor Due to Tubing Length
5.3.1
SX 9, 12 DCI :Cooling
Capacity Ratio
5.3
1.01
1.00
0.99
0.98
0.97
0.96
0.95
0.94
0.93
0.92
0.91
3 4
5 6
7 8
9 10 11 12 13 14 15 16 17 18 19 20
Tubing Length [m ]
5.3.2
Heating
Capacity Ratio
1.02
1.00
0.98
0.96
0.94
0.92
0.90
3
4 5
6 7
8
9 10 11 12 13 14 15 16 17 18 19 20
Tubing Length [m ]
SM SX DCI 1-A.3 GB
CONTENT
5-9
PERFORMANCE DATA & PRESSURE CURVES
5.4
SX18 DCI
5.4.1
Cooling Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB/WB TEMPERATURE [oC]
OU COIL
ENTERING AIR DB
TEMPERATURE [oC]
22/15
24/17
29/21
32/23
TC
SC
PI
TC
SC
PI
TC
SC
PI
4.93
3.35
1.25
4.67
3.22
1.42
80 - 110 % of nominal
80 - 105 % of nominal
25 - 50 % of nominal
5.22
5.51
5.80
3.40
3.45
3.50
1.28
1.30
1.33
4.96
5.25
5.54
3.27
3.32
3.37
1.48
1.45
1.50
6.09
3.55
1.36
5.83
3.42
1.53
TC
4.42
4.71
5.00
5.29
5.58
SC
3.09
3.14
3.24
3.29
PI
1.59
1.62
3.19
1.65
1.68
1.71
TC
SC
PI
TC
SC
PI
4.17
2.96
1.77
3.86
2.80
1.98
4.46
3.01
1.80
4.15
2.85
2.00
4.75
3.06
1.82
4.44
2.90
2.03
5.04
3.11
1.85
4.73
2.95
2.06
5.33
3.16
1.88
5.02
3.00
2.09
DATA
-10 - 20
(protection range)
25
30
35
40
46
27/19
LEGEND
TC
SC
PI
WB
DB
ID
OU
5.4.2
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Cooling Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ratio
1.10
1.00
0.90
0.80
0.70
0.60
0.50
20
25
30
35
40
45
Outdoor Temperature [ºC]
5-10
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.4.3
Heating Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB TEMPERATURE [oC]
OU COIL
ENTERING
AIR DB/WB
TEMPERATURE
[oC]
-15/-16
-10/-12
-7/-8
-1/-2
2/1
7/6
10/9
15/12
15-24
(Protection Range)
DATA
15
20
25
TC
PI
TC
PI
TC
PI
TC
PI
TC
2.64
1.18
3.48
1.34
4.12
1.45
4.43
1.51
4.65
1.88
1.35
2.72
1.50
3.36
1.62
3.67
1.68
3.89
PI
1.55
2.26
1.27
3.10
1.42
3.74
1.54
4.05
1.59
4.27
1.63
TC
PI
TC
PI
TC
PI
TC
PI
6.18
1.61
6.50
1.64
6.82
1.67
5.80
1.69
5.42
1.77
5.74
1.81
6.06
1.84
1.72
6.12
1.72
6.44
1.75
85 - 105 % of nominal
80 - 120 % of nominal
LEGEND
TC
PI
WB
DB
ID
OU
5.4.4
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Heating Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ration
1.10
1.00
0.90
0.80
0.70
0.60
0.50
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [deg C]
SM SX DCI 1-A.3 GB
CONTENT
5-11
PERFORMANCE DATA & PRESSURE CURVES
5.4.5
Model: SX 18 DCI Cooling – Test Mode
Suction Pressure VS.Outdoor Temp.
Suction Pressure [kPa]
1400
Indoor
DB/WB
1300
1200
1100
22/15
1000
24/17
27/19
900
29/21
800
32/23
700
600
500
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
Discharge Pressure [kPa]
Discharge Pressure VS. Outdoor Temp.
4250
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
Outdoor DB Temperature[ºC ]
5-12
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.4.6
Heating – Test Mode
Suction Pressure VS.Outdoor Temp.
Suction Pressure [kPa]
1100
1000
900
15
800
20
700
25
600
500
400
300
200
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
Discharge Pressure [kPa]
Discharge Pressure VS. Outdoor Temp.
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
-15
Indoor DB
15
20
25
-10
-5
0
5
10
15
Outdoor WB Temperature [ºC]
SM SX DCI 1-A.3 GB
CONTENT
5-13
PERFORMANCE DATA & PRESSURE CURVES
5.5
Capacity Correction Factor Due to Tubing Length
5.5.1
SX 18 DCI :Cooling
1.01
Capacity ratio
0.99
0.97
0.95
0.93
0.91
0.89
4
6
8
10 12
14
16 18
20
22 24
26 28
30
Tubing length(m )
Heating
Capacity ratio
5.5.2
1.02
1.00
0.98
0.96
0.94
0.92
0.90
0.88
0.86
0.84
4
6
8
10 12
14 16 18 20
22 24 26
28 30
Tubing Length(m )
5-14
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.6
SX 24 DCI
5.6.1
Cooling Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB/WB TEMPERATURE [oC]
OU COIL
ENTERING AIR DB
TEMPERATURE [oC]
22/15
24/17
29/21
32/23
TC
SC
PI
TC
SC
PI
TC
SC
PI
6.70
5.36
1.70
6.35
5.15
1.94
80 - 110 % of nominal
80 - 105 % of nominal
25 - 50 % of nominal
7.09
7.49
7.88
5.44
5.52
5.60
1.74
1.78
1.82
6.75
7.14
7.54
5.23
5.31
5.39
2.01
1.98
2.05
8.28
5.68
1.85
7.93
5.47
2.09
TC
6.01
6.41
6.80
7.19
7.59
SC
4.94
5.02
5.18
5.26
PI
2.17
2.21
5.10
2.25
2.29
2.33
TC
SC
PI
TC
SC
PI
5.67
4.73
2.41
5.26
4.48
2.69
6.06
4.81
2.45
5.65
4.56
2.73
6.46
4.89
2.49
6.04
4.64
2.77
6.85
4.97
2.52
6.44
4.72
2.81
7.25
5.05
2.56
6.83
4.80
2.85
DATA
-10 - 20
(protection range)
25
30
35
40
46
27/19
LEGEND
TC
SC
PI
WB
DB
ID
OU
5.6.2
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Cooling Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ratio
1.10
1.00
0.90
0.80
0.70
0.60
0.50
20
25
30
35
40
45
Outdoor Temperature [ºC]
SM SX DCI 1-A.3 GB
CONTENT
5-15
PERFORMANCE DATA & PRESSURE CURVES
5.6.3
Heating Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB TEMPERATURE [oC]
OU COIL
ENTERING
AIR DB/WB
TEMPERATURE
[oC]
-15/-16
-10/-12
-7/-8
-1/-2
2/1
7/6
10/9
15/12
15-24
(Protection Range)
DATA
15
20
25
TC
PI
TC
PI
TC
PI
TC
PI
TC
3.46
1.48
4.57
1.67
5.40
1.81
5.81
1.88
6.09
2.46
1.69
3.57
1.88
4.40
2.02
4.81
2.10
5.09
PI
1.93
2.96
1.58
4.07
1.77
4.90
1.92
5.31
1.99
5.59
2.04
TC
PI
TC
PI
TC
PI
TC
PI
8.10
2.00
8.52
2.04
8.94
2.08
7.60
2.11
7.10
2.22
7.52
2.25
7.94
2.29
2.14
8.02
2.15
8.44
2.19
85 - 105 % of nominal
80 - 120 % of nominal
LEGEND
TC
PI
WB
DB
ID
OU
5.6.4
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Heating Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ration
1.10
1.00
0.90
0.80
0.70
0.60
0.50
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [deg C]
5-16
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.6.5
Model: SX 24 DCI Cooling – Test Mode
Suction Pressure [kPa]
Suction Pressure Vs. Outdoor Temp.
1000
960
920
880
840
800
760
720
680
640
600
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
O
Outdoor DB Temperature[ C]
Discharge Pressure [kPa]
Discharge Pressure Vs. Temp.
3900
3700
3500
3300
3100
2900
2700
2500
2300
2100
1900
1700
1500
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
O
Outdoor DB Temperature[ C]
SM SX DCI 1-A.3 GB
CONTENT
5-17
PERFORMANCE DATA & PRESSURE CURVES
5.6.6
Heating – Test Mode
Suction Pressure Vs. Outdoor Temp.
Suction Pressure [kPa]
1050
950
850
Indoor DB
750
15
650
550
20
450
25
350
250
-15
-10
-5
0
5
10
15
O
Outdoor WB Temperature[ C]
Discharge Pressure [kPa]
Discharge Pressure Vs. Outdoor Temp.
3700
3500
3300
3100
2900
2700
2500
2300
2100
1900
1700
Indoor DB
15
20
25
-15
5-18
-10
-5
0
5
O
Outdoor WB Temperature[ C]
CONTENT
10
15
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.7
Capacity Correction Factor Due to Tubing Length
5.7.1
SX 24 DCI :Cooling
1.01
0.99
Capacity Ratio
0.97
0.95
0.93
0.91
0.89
0.87
0.85
5
Heating
Tube Length(m)
5.7.2
6
7
7.5
10
15
20
25
30
Tube Length [m])
5
6
7
7.5
10
15
20
20
25
25
Heating
1.05
Capacity Ratio
1.00
0.95
0.90
0.85
0.80
0.75
0.70
5
SM SX DCI 1-A.3 GB
6
7
7.5
10
15
Tube Length [m]
CONTENT
30
5-19
PERFORMANCE DATA & PRESSURE CURVES
5.8
SX 30 DCI
5.8.1
Cooling Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB/WB TEMPERATURE [oC]
OU COIL
ENTERING AIR DB
TEMPERATURE [oC]
22/15
24/17
29/21
32/23
TC
SC
PI
TC
SC
PI
TC
SC
PI
7.39
5.72
1.88
7.01
5.49
2.14
80 - 110 % of nominal
80 - 105 % of nominal
25 - 50 % of nominal
7.82
8.26
8.69
5.80
5.88
5.97
1.92
1.97
2.01
7.44
7.88
8.31
5.58
5.66
5.75
2.23
2.19
2.27
9.13
6.05
2.05
8.75
5.83
2.31
TC
6.63
7.07
7.50
7.94
8.37
SC
5.27
5.35
5.52
5.61
PI
2.41
2.45
5.44
2.49
2.53
2.57
TC
SC
PI
TC
SC
PI
6.25
5.05
2.67
5.80
4.78
2.98
6.69
5.13
2.71
6.23
4.86
3.02
7.12
5.22
2.75
6.67
4.95
3.07
7.56
5.30
2.79
7.10
5.03
3.11
7.99
5.39
2.84
7.54
5.12
3.15
DATA
-10 - 20
(protection range)
25
30
35
40
46
27/19
LEGEND
TC
SC
PI
WB
DB
ID
OU
5.8.2
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Cooling Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ratio
1.10
1.00
0.90
0.80
0.70
0.60
0.50
20
25
30
35
40
45
Outdoor Temperature [ºC]
5-20
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.8.3
Heating Capacity (kW) - Run Mode
230[V] : Indoor Fan at High Speed.
ID COIL ENTERING AIR DB TEMPERATURE [oC]
OU COIL
ENTERING
AIR DB/WB
TEMPERATURE
[oC]
DATA
15
20
25
TC
PI
TC
PI
TC
PI
TC
PI
TC
3.96
1.78
5.23
2.02
6.18
2.19
6.65
2.28
6.97
2.82
2.04
4.09
2.27
5.04
2.44
5.51
2.53
5.83
PI
2.34
3.39
1.91
4.66
2.14
5.61
2.32
6.08
2.40
6.40
2.46
TC
PI
TC
PI
TC
PI
TC
PI
9.27
8.70
2.55
2.42
9.75
9.18
2.47
2.60
10.23
9.66
2.52
2.64
85 - 105 % of nominal
80 - 120 % of nominal
8.13
2.68
8.61
2.72
9.09
2.77
-15/-16
-10/-12
-7/-8
-1/-2
2/1
7/6
10/9
15/12
15-24
(Protection Range)
2.59
LEGEND
TC
PI
WB
DB
ID
OU
5.8.4
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factors
Heating Capacity Ratio Vs. Outdoor Temperature
1.20
Capacity Ration
1.10
1.00
0.90
0.80
0.70
0.60
0.50
-15
-10
-5
0
5
10
15
Outdoor WB Temperature [deg C]
SM SX DCI 1-A.3 GB
CONTENT
5-21
PERFORMANCE DATA & PRESSURE CURVES
5.8.5
Model: SX 30 DCI Cooling – Test Mode
Suction Pressure [kPa]
Suction Pressure Vs. Outdoor Temp.
1000
960
920
880
840
800
760
720
680
640
600
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
O
Outdoor DB Temperature[ C]
Discharge Pressure [kPa]
Discharge Pressure Vs.Outdoor Temp.
3900
3700
3500
3300
3100
2900
2700
2500
2300
2100
1900
1700
1500
Indoor
DB/WB
22/15
24/17
27/19
29/21
32/23
10
15
20
25
30
35
40
45
O
Outdoor DB Temperature[ C]
5-22
CONTENT
SM SX DCI 1-A.3 GB
PERFORMANCE DATA & PRESSURE CURVES
5.8.6
Heating – Test Mode
Suction Pressure [kPa]
Suction Pressure Vs.Outdoor Temp.
1150
1050
950
850
750
650
550
450
350
250
Indoor DB
15
20
25
-15
-10
-5
0
5
10
15
Outdoor WB Temperature[OC]
Discharge Pressure [kPa]
Discharge Pressure Vs.Outdoor Temp.
3850
3600
3350
3100
2850
2600
2350
2100
1850
1600
Indoor DB
15
20
25
-15
-10
-5
0
5
10
15
O
Outdoor WB Temperature[ C]
SM SX DCI 1-A.3 GB
CONTENT
5-23
PERFORMANCE DATA & PRESSURE CURVES
5.9
Capacity Correction Factor Due to Tubing Length
5.9.1
SX 80 DCI :Cooling
1.01
1.00
Capacity Ratio
0.99
0.98
0.97
0.96
0.95
0.94
0.93
0.92
Heating 5
Tube Length(m)
Capacity Ratio
5.9.2
6
5
1.00
7
6
1.00
7.5
10
15
7.5
10
15
7
7.5
10
Tube length [m]
1.00 1.00 0.981
20
25
15
0.943
20
0.904
20
25
30
25
0.865
Heating
1.05
Capacity Ratio
1.00
0.95
0.90
0.85
0.80
5
6
7
30
Tube Length [m]
5-24
CONTENT
SM SX DCI 1-A.3 GB
SOUND LEVEL CHARACTERISTICS
6.
SOUND LEVEL CHARACTERISTICS
6.1
Sound Pressure Level
Unit
1m
Wall
Mic.
Ground
Figure 1
6.2
Soud Pressure Level Spectrum (Measured as Figure 1)
SX 9
FAN SPEED
SX 12
LINE
HI
ME
LO
SM SX DCI 1-A.3 GB
CONTENT
6-1
SOUND LEVEL CHARACTERISTICS
SX 18
SX 24
SX 30
FAN SPEED
LINE
HI
ME
LO
6-2
CONTENT
SM SX DCI 1-A.3 GB
SOUND LEVEL CHARACTERISTICS
6.3
Outdoor units
Unit
1m
Mic.
Ground
Figure 2
6.4
Sound Pressure Level Spectrum (Measured as Figure 2)
GC 9 DCI Cooling
GC 9 DCI Heating
GC 12 DCI Cooling
GC 12 DCI Heating
SM SX DCI 1-A.3 GB
CONTENT
6-3
SOUND LEVEL CHARACTERISTICS
FAN SPEED
GC 18 DCI Cooling
GC 18 DCI Heating
GC 24 DCI Cooling
GC 24 DCI Heating
LINE
HI
ME
LO
6-4
CONTENT
SM SX DCI 1-A.3 GB
SOUND LEVEL CHARACTERISTICS
GC 30 DCI Cooling
FAN SPEED
GC 30 DCI Heating
LINE
HI
ME
LO
SM SX DCI 1-A.3 GB
CONTENT
6-5
ELECTRICAL DATA
7.
ELECTRICAL DATA
7.1
Single Phase Units
MODEL
SX 9 DCI
SX 12 DCI
SX 18 DCI
SX 24 DCI
SX 30 DCI
To indoor
To indoor
To indoor
To outdoor
To outdoor
Power Supply
1PH-230V50Hz
1PH-230V50Hz
1PH-230V50Hz
1PH-230V50Hz
1PH-230V50Hz
Max Current, A
10
10
12
14
15
Inrush Current A
35
35
35
45
45
Starting Current A
10.5
10.5
10.5
10.5
10.5
Circuit Breaker A
16
16
20
20
20
Power Supply Wiring No.X Cross
Section mm2
3 x 1.5 mm2
3 x 1.5 mm2
3 x 2.5 mm2
3 x 2.5 mm2
3 x 2.5 mm2
Interconnecting Cable No.X Cross
Section mm2
4 x 1.5 mm2
4 x 1.5 mm2
4 x 2.5 mm2
4 x 2.5 mm2
4 x 2.5 mm2
NOTE
Power wiring cord should comply with local lows and electrical
regulations requirements.
SM SX DCI 1-A.3 GB
CONTENT
7-1
B la c k
Red
B ro w n
U V W
W h it e
P1 4
P4
1 2
P1
1
2
1 2 3 4 5 6
P16
P17 P18 P21 P22
P2
1 2
OAT
P19
1 2
CONTENT
Blue
R ed
Black
L-F
N-F
COM
NCOM
L
N
COM
E AR TH E AR TH
FUSE
Brown
Red
Y/G
magnetic ring
N/3
L/4
C/5
B lu e
Brown
Red
Y/G
POWE R SU PPL Y
Blue
Brown
Red
Y/G
SX 9, 12, 18 DCI / GC 9, 12, 18 DCI
EEV
8.1
Y/G
P6 1 2 3 4
WIRING DIAGRAMS
EMI f i l t er PCB
1 2 3 4 5 6
EARTH
L N COM N-COM
megatool
P8
1 2
D i sp l ay
8.
Y/G
P7
6 5 4 3 2 1
J P9
P1 2
P10
P20
1 2
OCT CTT SUCT
Outdoor unit controller PCB
P3 P9 P11 P13
heater
V dc
Red
Ba s e
B la c k
Choke coil
B lu e
OFAN
EARTH
V cc
V sp
O ra n g e
Reverse
valve
B lu e
SM SX DCI 1-A.3 GB
Y e llo w
COMP
FG
OUTDOOR UNIT CIRCUIT DIAGRAM
WIRING DIAGRAMS
8-1
WIRING DIAGRAMS
8.2
8-2
Indoor Unit: SX 24, 30 DCI
CONTENT
SM SX DCI 1-A.3 GB
WIRING DIAGRAMS
8.3
Outdoor Unit: GC 24, 30 DCI
SM SX DCI 1-A.3 GB
CONTENT
8-3
REFRIGERATION DIAGRAMS
9.
REFRIGERATION DIAGRAMS
9.1
SX 9, 12, 18, 24, 30 DCI
Cooling Mode
EEV
Heating Mode
EEV
SM SX DCI 1-A.3 GB
CONTENT
9-1
TUBING CONNECTIONS
10.
TUBING CONNECTIONS
TUBE (Inch)
¼”
⅜”
½”
⅝”
¾”
11-13
13-20
11-13
40-45
13-20
11-13
60-65
18-25
11-13
70-75
18-25
11-13
80-85
40-50
11-13
TORQUE (Nm)
Flare Nuts
Valve Cap
Service Port Cap
1.
2.
3.
4.
5.
6.
7.
8.
Valve Protection Cap-end
Refrigerant Valve Port (use Allen wrench to open/close)
Valve Protection Cap
Refrigerant Valve
Service Port Cap
Flare Nut
Unit Back Side
Copper Tube
When the outdoor unit is installed above the indoor unit an oil trap is required every 5m along the suction
line at the lowest point of the riser. Incase the indoor unit is installed above the outdoor, no trap is
required.
SM SX DCI 1-A.3 GB
CONTENT
10-1
TROUBLESHOOTING
11.
TROUBLESHOOTING
WARNING!!!
When Power Up – the whole outdoor unit controller, including the wiring, is under
HIGH VOLTAGE!!!
Never open the Outdoor unit before turning off the Power!!!
When turned off, the system is still charged (400V)!!!
It takes about 3 Min. to discharge the system.
Touching the controller before discharging may cause an electrical shock!!!
For safe handling of the controller please refer to section 11.6 below.
11.1
General DCI Single Split System failures and Corrective Actions
PROBABLE
CAUSE
No
SYMPTOM
1
Power supply indicator (Red
LED) does not light up.
No power supply
Check power supply. If power supply
is OK, check display and display
wiring. if OK, replace controller.
2
Unit does not respond to
remote control message
Remote
control
message not reached
the indoor unit
Check remote control batteries, if
batteries are OK, check display and
display wiring, if OK, replace display
PCB.
If still not OK replace controller.
3
Unit responds to remote
control message but Operate
indicator (Green LED) does
not light up
Problem with display
PCB
Replace display PCB.
If still not OK replace controller.
Unit in heat mode and
coil is still not warm.
Change to cool mode and check.
Problem with PCB or
capacitor
Change to high speed and Check
power supply to motor is higher than
130VAC (for triack controlled motor)
or higher than 220VAC for fixed speed
motors, if OK replace capacitor, if not
OK replace controller
5
Indoor fan works when unit
is OFF, and indoor fan speed
is not changed by remote
control command.
PCB problem
Replace controller
6
Compressor does not start
Electronics control
problem or protection
Perform diagnostics (See 11.3), and
follow the actions described.
7
Compressor stops during
operation and Green LED
remains on
Electronic control
or power supply
problem
Perform diagnostics (See 11.3), and
follow the actions described.
4
Indoor fan does not start
(louvers are opened and
Green LED does light up)
SM SX DCI 1-A.3 GB
CONTENT
CORRECTIVE ACTION
11-1
TROUBLESHOOTING
No
SYMPTOM
PROBABLE
CAUSE
CORRECTIVE ACTION
8
Compressor is on but outdoor
fan does not work
Problem with outdoor
electronics or
outdoor fan
Check outdoor fan motor according
to the procedure in section 11.5.3 , if
not OK replace controller
9
Unit works in wrong mode
(cool instead of heat or heat
instead of cool)
Electronics or power
connection to RV
Check RV power connections, if OK,
Check RV
operation with direct
230VAC power supply, if OK,
Replace outdoor controller.
10
All components are operating
properly but no cooling or no
heating
Refrigerant leak
Check refrigeration system.
11
Compressor is over heated
and unit does not generate
capacity
EEV problem
Check EEV
12
Units goes into protections
and compressor is stopped
with no clear reason
Control problem or
refrigeration system
problem
Perform diagnostics (See 11.3), and
follow the actions described.
13
Compressor
motor
generating noise and
suction occurs
Phase order to
compressor is wrong
Check compressor phase order.
14
Water leakage from indoor
unit
Indoor unit drainage
tube is blocked
Check and open drainage tube.
15
Freezing of outdoor unit in
heat mode and outdoor unit
base is blocked with ice
16
Unit operates with wrong fan
speeds or wrong frequency
11.2
is
no
Connect base heater.
Wrong jumper
settings
Perform diagnostics (See 11.3), and
check if units is operating by EEPROM
parameters.
Checking the refrigeration system
Checking system pressures and other thermodynamic measures should be done when system
is in Test Mode (in Test mode, system operates in fixed settings). The performance curves
given in this manual are given for unit performance in test mode when high indoor fan speed is
selected.
Entering test mode:
Set unit to Cool/16 degrees/High indoor fan speed, or Heat/30 degrees/High indoor fan speed,
and enter diagnostics.
11.3
Judgment by Indoor/Outdoor Unit Diagnostics
Enter diagnostics mode - press for five seconds Mode button in any operation mode.
Acknowledgment is by 3 short beeps and lights of COOL and HEAT LED’s. Then, every short
pressing of Mode button will scroll between Indoor and Outdoor unit diagnostic modes by the
acknowledgment of 3 short beeps and lighting of COOL and HEAT LED’s.
During the Outdoor unit diagnostics all four Indoor LED’s (STBY, Operate, Filter and Timer)
are blinking. When Indoor diagnostics is displayed, all four LED’s (STBY, Operate, Filter and
Timer) are ON.
11-2
CONTENT
SM SX DCI 1-A.3 GB
TROUBLESHOOTING
When system enters diagnostics mode, only one fault code is shown. Order of priority is from
the lower to the higher number. Diagnostics is continuously ON as long as power is ON. The
current system operation mode will not be changed.
If no fault occurred in the system, no fault code will be displayed during normal operation
mode. The last fault code will be displayed even if the system has recovered from that
fault. The last fault will be deleted from the EEPROM after the system has exit diagnostics
mode.
In diagnostics mode, system fault / status will be indicated by blinking of Heat & Cool LEDs.
The coding method will be as follows:
Heat LED will blink 5 times in 5 seconds, and then will be shut off for the next 5 seconds. Cool
LED will blink during the same 5 seconds according to the following Indoor / Outdoor unit
tables:
Note: 0 – OFF, 1-ON
11.3.1
Indoor Unit Diagnostics
●
Alarm Output
The Alarm Output dry contact will be on (closed), when a predefined set faults occur.
The fault set is defined under diagnostics section.
The alarm output will be off (open), when the predefined fault is cleared.
The indoor alarm outputs are defined according to the following table:
No
Problem
AO
5
4
3
2
1
1
ICT is disconnected
Yes
0
0
0
0
1
2
ICT is shorted
Yes
0
0
0
1
0
3
RAT is disconnected
Yes
0
0
0
1
1
4
RAT is shorted
Yes
0
0
1
0
0
5
Reserved (for MSMP used as RGT fault)
No
0
0
1
0
1
ICTE shorted/disconnected (when enabled)
Yes
0
0
1
1
0
Undefined IDU family/model
Yes
0
0
1
1
1
8
No Communication
Yes
0
1
0
0
0
9
No Encoder
No
0
1
0
0
1
10
Reserved
No
0
1
0
1
0
11
Outdoor Unit Fault
No
0
1
0
1
1
…
Reserved
No
17
Defrost protection
No
1
0
0
0
1
18
Deicing Protection
No
1
0
0
1
0
19
Outdoor Unit Protection
No
1
0
0
1
1
20
Indoor Coil HP Protection
No
1
0
1
0
0
21
Overflow Protection
Yes
1
0
1
0
1
22
Reserved
No
24
EEPROM Not Updated
No
1
1
0
0
0
25
Bad EEPROM
No
1
1
0
0
1
26
Bad Communication
No
1
1
0
1
0
27
Using EEPROM data
No
1
1
0
1
1
*6
*7
SM SX DCI 1-A.3 GB
CONTENT
11-3
TROUBLESHOOTING
No
Problem
AO
5
4
3
2
1
28
Model A
No
1
1
1
0
0
29
Model B
No
1
1
1
0
1
30
Model C
No
1
1
1
1
0
31
Model D
No
1
1
1
1
1
* CN / LSN Units only
11.3.2
Indoor Unit Diagnostics and Corrective Actions
No.
Fault
Probable Cause
Corrective Action
1
Sensor failures
of all types
Check sensor connections or
replace sensor
2
Communication
mismatch
Indoor and Outdoor
controllers are with
different versions
Replace Indoor controller
3
No
Communication
Communication or
grounding wiring is not
good.
Check Indoor to Outdoor
wiring and grounding
4
No Encoder
Indoor electronics or
motor
Check motor wiring, if ok,
replace motor, if still not ok,
replace Indoor controller.
5
Outdoor Unit
Fault
Outdoor controller
problem
Switch to Outdoor
diagnostics.
6
EEPROM Not
Updated
System is using ROM
parameters and not
EEPROM parameters
No action, unless special
parameters are required for
unit operation.
7
Bad EEPROM
8
Bad
Communication
Communication quality
is low reliability
9
Using EEPROM
data
No problem. System is
using EEPRRRROM
parameters
No action, unless special
parameters are required for
unit operation.
Check Indoor to Outdoor
wiring and grounding
11.3.3
Outdoor Unit Diagnostics
The outdoor alarm outputs are defined in the following way:
No
Problem
AO
5
4
3
2
1
1
OCT is disconnected
Yes
0
0
0
0
1
2
OCT is shorted
Yes
0
0
0
1
0
3
CTT is disconnected
Yes
0
0
0
1
1
4
CTT is shorted
Yes
0
0
1
0
0
5
HST is disconnected (when enabled)
Yes
0
0
1
0
1
6
HST is shorted (when enabled)
Yes
0
0
1
1
0
7
OAT is disconnected (when enabled)
Yes
0
0
1
1
1
8
OAT is shorted (when enabled)
Yes
0
1
0
0
0
9
OMT is disconnected (DCI72 / 72Z / 80)
Yes
0
1
0
0
1
11-4
CONTENT
SM SX DCI 1-A.3 GB
TROUBLESHOOTING
No
Problem
AO
5
4
3
2
1
10
OMT is shorted (DCI72 / 72Z / 80)
Yes
0
1
0
1
0
11
IPM Fault
Yes
0
1
0
1
1
12
Bad EEPROM
No
0
1
1
0
0
13
DC under voltage
Yes
0
1
1
0
1
14
DC over voltage
Yes
0
1
1
1
0
15
AC under voltage
Yes
0
1
1
1
1
16
Mismatch IDU & ODU models (*SW 35V14 and above)
Yes
1
0
0
0
0
17
No Communication
Yes
1
0
0
0
1
18
Reserved
No
1
0
0
1
0
20
Heat sink Over Heating
No
1
0
1
0
0
21
Deicing
No
1
0
1
0
1
22
Compressor Over Heating
No
1
0
1
1
0
23
Compressor Over Current
No
1
0
1
1
1
24
No OFAN Feedback
No
1
1
0
0
0
25
OFAN locked
Yes
1
1
0
0
1
26
Compressor Lock
Yes
1
1
0
1
0
27
Bad Communication
No
1
1
0
1
1
28
Missing ODU configuration (*SW 35V14 and above)
Yes
1
1
1
0
0
29
Undefined ODU Model (*SW 35V14 and above)
Yes
1
1
1
0
1
30
For future use
No
1
1
1
1
0
31
Operation condition is exceeded (*SW 35V14 and above)
Yes
1
1
1
1
1
*Alarm Output - is on SW 35V14 and above. There is no alarm on SW 35V12 and below/
11.3.4
Outdoor Unit Diagnostics and Corrective Actions
No.
Fault
1
Sensors failures of all
types
Check sensors connections
or replace sensors.
2
IPM Fault
Check all wiring and jumper
settings, if OK, replace
electronics.
3
Bad EEPROM
4
DC under/over Voltage
5
AC under Voltage
6
Indoor / Outdoor unit
Communication mismatch
Indoor and Outdoor
controllers are with
different versions
Replace Indoor controller
No Communication
Communication or
grounding wiring is not
good.
Check Indoor to Outdoor
wiring and grounding
7
SM SX DCI 1-A.3 GB
Probable Cause
Electronics HW problem
Corrective Action
No action, unless special
parameters are required for
unit operation.
Electronics HW problem
Check outdoor unit power
supply voltage
Check outdoor unit power
supply voltage
CONTENT
11-5
TROUBLESHOOTING
No.
Fault
8
Compressor Lock
9
Bad Communication
11.4
Probable Cause
Corrective Action
Switch unit to STBY and
restart
If still not ok check compressor
(11.5.4)
If comp is ok replace OU
controller
If compressor is not ok replace
compressor
Communication quality
is low reliability
Check Indoor to Outdoor
wiring and grounding
Judgment by MegaTool
MegaTool is a special tool to monitor the system states.
Using MegaTool requires:
•
•
•
A computer with RS232C port.
•
•
Setup MegaTool software: copy the software to the computer.
•
Run the software and choose the COM port, you can monitor the A/C system state in
monitor tab.
A connection wire for MegaTool.
A special MegaTool software.
Use MegaTool according to following procedure:
Connect RS232C port in computer with MegaTool port in Indoor/Outdoor unit controller by
the connection wire.
11.5
Simple procedures for checking the Main Parts
11.5.1
Checking Mains Voltage.
Confirm that the Mains voltage is between 198 and 264 VAC. If Mains voltage is out of this
range, abnormal operation of the system is expected. If in range check the Power (Circuit)
Breaker and look for broken or loosed cable lugs or wiring mistake(s).
11.5.2
Checking Power Input.
If Indoor unit power LED is unlighted, power down the system and check the fuse of the Indoor
unit. If the fuse is OK replace the Indoor unit controller. If the fuse has blown, replace the fuse
and power up again.
Checking Power Input procedure for the Outdoor unit is the same as with the Indoor unit.
11.5.3
Checking the Outdoor Fan Motor.
Enter Test Mode (where the OFAN speed is high)
Check the voltage between lead wires according to the normal value as following:
•
•
•
11-6
Between red wire and black wire: 310VDC +/- 20V
Between orange wire and black wire: 15VDC +/- 1V
Between yellow wire and black wire: 2-6VDC
CONTENT
SM SX DCI 1-A.3 GB
TROUBLESHOOTING
11.5.4
Checking the Compressor.
The compressor is brushless permanence magnetic DC motor. Three coil resistance is same.
Check the resistance between three poles. The normal value should be below 0.5 ohm
(TBD).
11.5.5
Checking the Reverse Valve (RV).
Running in heating mode, check the voltage between two pins of reverse valve connector,
normal voltage is 220VAC.
11.5.6
Checking the electrical expansion valve (EEV).
The EEV has two parts, drive part and valve. The drive part is a step motor; it is ringed on the
valve. Check the drive voltage (12VDC). When Outdoor unit is power on, EEV shall run and
have click and vibration.
11.6
Precaution, Advise and Notice Items
11.6.1
High voltage in Outdoor unit controller.
Whole controller, including the wires that are connected to the Outdoor unit controller may
have the potential hazard voltage when power is on. Touching the Outdoor unit controller may
cause an electrical shock.
Advise: Don’t touch the naked lead wire and don’t insert finger, conductor or anything else into
the controller when power is on.
11.6.2
Charged Capacitors
Three large-capacity electrolytic capacitors are used in the Outdoor unit controller. Therefore,
charging voltage (380VDC) remains after power down. Discharging takes about four minutes
after power is off. Touching the Outdoor unit controller before discharging may cause an
electrical shock.
11.6.3
w
Additional advises
•
•
When disassemble the controller or the front panel, turn off the power supply.
•
There are sharp fringes and sting on shell. Use gloves when disassemble the A/C units.
When connecting or disconnecting the connectors on the PCB, hold the whole housing,
don’t pull the wire.
SM SX DCI 1-A.3 GB
CONTENT
11-7
CONTROL SYSTEM
12.
CONTROL SYSTEM
12.1
General Functions and Operating Rules
The DCI software is fully parametric.
All the model dependent parameters are shown in Blue color and with Italic style [parameter].
The parameters values are given in the last section of this control logic chapter of the service
manual.
12.1.1
System Operation Concept
The control function is divided between indoor and outdoor unit controllers. Indoor unit is the system
‘Master’, requesting the outdoor unit for cooling/heating capacity supply. The outdoor unit is the
system ‘Slave’ and it must supply the required capacity unless it enters into a protection mode
avoiding it from supplying the requested capacity.
The capacity request is transferred via indoor to outdoor communication, and is represented by
aparameter called ‘NLOAD’. NLOAD is an integer number with values between 0 and 127, and it
represents the heat or cool load felt by the indoor unit.
12.1.2
Compressor Frequency Control
12.1.2.1 NLOAD setting
The NLOAD setting is done by the indoor unit controller, based on a PI control scheme.
The actual NLOAD to be sent to the outdoor unit controller is based on the preliminary LOADcalculation,
the indoor fan speed, and the power shedding function.
NLOAD limits as a function of indoor fan speed:
Indoor Fan Speed Maximum NLOAD Cooling Maximum NLOAD Heating
Indoor Fan Speed
Low
Medium
High
Turbo
Auto
Maxium NLOAD Cooling
Maxium NLOAD Heating
MaxNLOADIF1C
MaxNLOADIF2C
MaxNLOADIF3C
MaxNLOADIF4C
MaxNLOADIF5C
MaxNLOADIF1H
MaxNLOADIF2H
MaxNLOADIF3H
MaxNLOADIF4H
MaxNLOADIF5H
NLOAD limits as a function of power shedding:
Mode
Cooling
Heating
12.1.3
Power Shedding OFF
No limit
No limit
Power Shedding ON
Nominal Cooling
Nominal heating
Target Frequency Setting
12.1.3.1 Target Frequency Setting for DCI 50/60/72Z
The compressor target frequency is a function of the NLOAD number sent from the indoor
controller and the outdoor air temperature.
Basic Target Frequency Setting:
NLOAD
127
10<NLOAD<127
10
0
SM SX DCI 1-A.3 GB
Target Frequency
Maximum Frequency
Interpolated value between minimum and maximum frequency
Minimum frequency
Compressor is stopped
CONTENT
12-1
CONTROL SYSTEM
Target frequency limits as a function of outdoor air temperature (OAT):
OAT Range
Cooling Mode limits
OAT < 6
Heating Mode limits
No limit
6 ≤ OAT < 15
MaxFreqAsOAT1H
MaxFreqAsOATC
15 ≤ OAT < 28
28≤ OAT
MaxFreqAsOAT2H
No limit
12.1.3.2 Target Frequency Setting for DCI 72/80
The compressor Target Speed is calculated according to the following formula:
ODUNload T arg et Speed load max MinSpeed , MaxSpeed 127
MiniSpeed, MaxSpeed are defined as following:
When the unit is in the cool mode, MiniSpeedC
= 15Hz, MaxSpeed = 75Hz
When the unit is in the heat mode, MiniSpeedH = 20Hz, MaxSpeed = 95Hz
ODU NLOAD is caculated according to the IDU NLoad:
3 * IDUNLOAD
ODU NLOAD min , 127 ODUCode
OAT
≤-5
≤-5
12.1.4
ODUCodeC
3
3.8
ODUCodeC
3
3
IDUNLOAD
Refer to sect.112.1.2.1
Frequency Changes Control
When the unit is running normally , the compressor frequency change rate is 1 Hz/sec.
12.1.5
Compressor Starting Control
12.1.5.1 Compressor starting control for DCI50/60/72Zzz
Step3
Step2
Step1
1
Minute
12-2
1
Minute
Time
Min 10 Minutes
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
12.1.5.2 Compressor starting control for DCI72/80
Step 1
Whenever the compressor starts up, after it has been off for more than 45 minutes, the compressor
frequency cannot go below Step1RPS for 3 continuous minutes (this rule comes to ensure oil return
to the compressor).
Step 2
The compressor speed cannot go above Step2RPS once after each compressor start up for 3
continuous minutes (this rule comes to prevent oil exit from the compressor after its start up).
Step 3
The speed cannot go higher than Step3RPS unless it was operating for more than 1 continuous
minutes between Step3RPS – 5 and Step3RPS .
After passing above Step3RPS, this rule is re-applied when passing below Step3RPS-5.
12.1.6
Minimum On and Off Time
3 minutes
12.1.7
Indoor Fan Control
8 Indoor fan speeds are determined for each model. 4 speeds for cool/dry/fan modes and 4 speeds
for heat mode.
When user sets the indoor fan speed to a fixed speed (Low/ Medium/ High), unit will operate constantly
at set speed.
When Auto Fan is selected, indoor unit controller can operate in all speeds. The actual speed is set
according to the cool/heat load.
12.1.7.1 Turbo Speed
The Turbo speed is activated during the first 30 minutes of unit operation when auto fan speed is
selected and under the following conditions:
Difference between set point and actual room temperature is bigger then 3 degrees.
Room temperature > 22 for cooling, or < 25 for heating.
12.1.8
Outdoor Fan Control
12.1.8.1 Outdoor Fan Control for DCI50/60
7 outdoor fan speeds are determined for each model. 3 speeds for cool and dry modes, and 3
speeds for heat mode, and a very low speed.
Outdoor fan speed is a function of compressor frequency and outdoor air temperature (OAT).
4 routines for fan control are determined. The control routine selection depends on operation mode,
compressor speed, outdoor air temperature (OAT) and heat sink temperature (HST).
Routine
Conditions
B
Heating with OAT < 15°C
or
Cooling with OAT > 20°C,
or
Faulty OAT
Cooling with 20°C > OAT > 7°C
C
Cooling with 7°C > OAT
D
Heating with OAT > 15°C
A
SM SX DCI 1-A.3 GB
CONTENT
12-3
CONTROL SYSTEM
OFAN Speed
Compressor
Target Frequency
Routin
A
Routin
B
Routin
C
Routin
D
Freq=0
OFF
OFF
OFF
OFF
10 ≤ Freq < OFLowFreq
Low
Low
VL
Low
OFLowFreq ≤ Freq< OFMedFreq
Medium
Low
VL
Low
OFMedFreq≤ Freq
High
Low
Low
Medium
When compressor is switched to OFF and the heat sink temperature is above 55 degrees, the
outdoor fan will remain ON in low speed for up to 3 minutes.
OFAN State
at Cool Mode
HST
Change To Higher
OFAN Cool state (*1)
3 Degrees
A
3 Degrees
B
50
C
7
20
OAT 45
Change To lower
OFAN Cool state
Note: Periorities A>B>C
(*1) If
State C, change to B
If State B, change to A
12.1.8.2 Outdoor Fan Control for GC 24, 30 DCI
OFAN operates between any speed OFMinRPM to OFMaxRPM.
The fan speed is also related to protections and OMT value.
* For DCI 72Z, in heating mode the OFAN speed is related to OCT.
12.1.9
EEV (Electronic Expansion Vavle) Control
12.1.9.1 EEV Control for GC 9, 12, 18 DCI
EEV opening is defined as EEV = EEVOL + EEVCV
EEVOL is the initial EEV opening as a function of the compressor frequency, operation mode, unit
model and capacity.
EEVCV is a correction value for the EEV opening that is based on the compressor temperature.
During the first 5 minutes of compressor operation EEVCV = 0.
Once the first 5 minutes are over, the correction value is calculated as follow: EEVCV(n) =
EEVCV(n-1) + EEVCTT
EEVCTT is the correction based on the compressor temperature. A target compressor temperature
is set depending on frequency and outdoor air temperature, and the actual compressor temperature
is compared to the target temperature to set the required correction to the EEV opening.
12-4
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
12.1.9.2 EEV Control for DCI72/72Z/80
The target EEV value is the sum of open loop value (OL) and a result of the accumulative
correction values (CV).
EEV EEVOL EEVCV
The EEV intial value(OL) is defined as follow:
EEVOL= EEVBaseOpenLoop + EEVOpenLoopCpctyCrct + EEVTubeCompnst
Basic EEV open loop
Open Loop correction
EEV tube Length
compensation
Mode
72/80
72/80
72/80
COOL
220
25
0
HEAT
170
30
0
*For DCI72Z
The initial EEVOL is defined in accordance to the compressor frequency
EEVCV is a correction value for the EEV opening that is based on the compressor temperature,
During the first 6 minutes after SB the correction is not calculated. After that the correction value is
updated every 30 seconds.
12.1.10
RV(Reversing Valve) Control
Reversing valve is on in heat mode.
Switching of RV state is done only after compressor is off for over 3 minutes.
12.1.11
Ioniser Control
Ioniser is on when unit is on ,AND indoor fan is on ,AND Ioniser power switch (on Ioniser) is on.
12.1.12
Base Heater Control
The base heater will be working only when RV is “ON” according to the following graph:
Base
Heater
OFF
ON
0
2
OAT
When OAT is faulty the base heater will be “ON” continuously in HEAT mode.
12.2
Fan Mode
In high/ medium/ low indoor fan user setting, unit will operate fan in selected speed.
In AutoFan user setting, fan speed will be adjusted automatically according to the differencebetween
actual room temperature and user set point temperature.
SM SX DCI 1-A.3 GB
CONTENT
12-5
CONTROL SYSTEM
12.3
Cool Mode
NLOAD is calculated according to the difference between actual room temperature and user set
point temperature by PI control.
In high/ medium/ low indoor fan user setting, unit will operate fan in selected speed.
In AutoFan user setting, fan speed will be adjusted automatically according to the calculated
NLOAD.
12.4
Heat Mode
NLOAD is calculated according to the difference between actual room temperature and user set
point temperature by PI control.
In high/ medium/ low indoor fan user setting, unit will operate fan in selected speed.
In AutoFan user setting, fan speed will be adjusted automatically according to the calculated
NLOAD.
12.4.1
Temperature Compensation
In wall mounted, ducted, and cassette models, 3 degrees are reduced from room temperature
reading (except when in I-Feel mode), to compensate for temperature difference between high and
low areas in the heated room, and for coil heat radiation on room thermistor.
The temperature compensation can be enabled/disabled by shortening of J2 on the indoor unit
Controller
Model
J2 Shorted
J2 Opened
Wall mounted
Cassette
Compensation Disabled
Compensation Enabled
Compensation Enabled
Compensation Disabled
Ducted
Floor/Ceiling
Compensation Enabled
Compensation Disabled
Compensation Disabled
Compensation Enabled
12.4.2
Indoor Fan Control in Heating Mode
Indoor fan speed depends on the indoor coil temperature:
12.5
Auto Cool/Heat Mode
When in auto cool heat mode unit will automatically select between cool and heat mode according
to the difference between actual room temperature and user set point temperature (.T). Unit will
switch from cool to heat when compressor is off for 3 minutes, and .T < -3.
Unit will switch from heat to cool when compressor is off for 5 minutes, and .T < -3.
12-6
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
12.6
Dry Mode
As long as room temperature is higher then the set point, indoor fan will work in low speed and
compressor will work between 0 and MaxNLOADIF1C Hz.
When the room temperature is lower than the set point, compressor will be switched OFF and indoor
fan will cycle 3 minutes OFF, 1 minute ON.
12.7
Protections
There are 5 protection codes.
Normal (Norm) – unit operate normally.
Stop Rise (SR) – compressor frequency can not be raised but does not have to be decreased.
HzDown1 (D1) – Compressor frequency is reduced by 2 to 5 Hz per minute.
HzDown2 (D2) – Compressor frequency is reduced by 5 to 10 Hz per minute.
Stop Compressor (SC) – Compressor is stopped.
12.7.1
Indoor Coil Defrost Protection
ICT Trend
ICT
Fast
Increasing
Increasing
No Change
Decreasing
Fast
ICT< -2
-2 ≤ ICT<0
0 ≤ ICT < 2
2 ≤ ICT< 4
4 ≤ ICT < 6
6 ≤ ICT ≤ 8
ICT> 8
SC
D1
SR
SR
Norm
Norm
SC
D1
SR
SR
Norm
Norm
SC
D2
D1
SR
SR
Norm
Norm
SC
D2
D2
D1
SR
SR
SC
D2
D2
D2
D1
SR
12.7.2
Indoor Coil Overheating Protection
12.7.2.1 Indoor Coil Overheating Protection For 50/60/72Z
ICT Trend
ICT
Fast
Decreasing
Decreasing
No Change
Increasing
Fast
Increasing
ICT >62
60 ≤ ICT < 62
55≤ ICT <60
52≤ ICT < 55
48≤ ICT < 52
45≤ ICT ≤ 48
ICT <45
SC
D1
SR
SR
Norm
Norm
SC
D1
SR
SR
Norm
Norm
SC
D2
D1
SR
SR
Norm
Norm
SC
D2
D2
D1
SR
SR
SC
D2
D2
D2
D1
SR
SM SX DCI 1-A.3 GB
CONTENT
12-7
CONTROL SYSTEM
12.7.2.2 Indoor Coil Overheating Protection For 72/80
ICT Trend
ICT
<-2
-2
-1,0,1
2
>2
ICT >62
SC
SC
SC
SC
SC
60 ≤ ICT < 62
D1
D1
D2
D2
D2
58≤ ICT <60
SR
SR
D1
D2
D2
56≤ ICT < 58
SR
SR
SR
D1
D2
54≤ ICT < 56
Norm
Norm
SR
SR
D1
52≤ ICT ≤ 54
Norm
Norm
Norm
SR
SR
ICT <52
12.7.3
Norm
Compressor Overheating Protection
12.7.3.1 Compressor Overheating Protection for DCI50/60/72Z
Compressor temperature can be in one of 5 control zones (4 in protection, and 1 normal),according
to the following chart.
CTT
105
102
98
94
Stop-Compressor
P3
P2
P1
Normal
Control Status
Compressor Temperature
Increases
Else
P1
Normal
Stop Rise
P2
HzDown 1
Stop Rise
P3
HzDown 2
HzDown 1
Stop Compressor
Stop Compressor
12-8
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
12.7.3.2 Compressor Overheating Protection for DCI72/80
CTT Trend
CTT
Fast
Decreasing
Decreasing
No
Change
Increasing
Fast
Increasing
CTT >105
100≤
CTT <
105
95≤CTT <100
SC
SC
SC
SC
SC
D1
D1
D2
D2
D2
SR
SR
D1
D2
D2
93≤CTT < 100
85≤CTT < 95
SR
SR
SR
D1
D1
90≤CTT ≤ 93
80≤CTT ≤ 85
Norm
Norm
Norm
SR
SR
CTT <90
CTT <80
Cool
Heat
CTT >105
100≤
CTT <
105
98≤CTT <100
12.7.4
Norm
Compressor Over Current Protection Only For DCI50/60/72Z
CCR
Stop-Compresor
CCROC4
HzDown2
CCROC3
HzDown1
CCROC2
Stop-Rise
CCROC1
Normal
12.7.5
Heat Sink Overheating Protection
12.7.5.1 Heat Sink Overheating Protection For DCI50/60/72Z
HST Trend
HST
Fast
Decreasing
Decreasing
No Change
Increasing
Fast
Increasing
HST ≥ 90
SC
SC
SC
SC
SC
85 ≤ HST < 90
D1
D1
D2
D2
D2
82 ≤ HST < 85
SR
SR
D1
D2
D2
80≤ HST< 82
SR
SR
SR
D1
D1
78 ≤ HST ≤ 80
Norm
Norm
Norm
SR
SR
HST < 78
SM SX DCI 1-A.3 GB
Norm
CONTENT
12-9
CONTROL SYSTEM
12.7.5.2 Heat Sink Overheating Protection For DCI72/80
Delta HST
HST
<-2
-2
-1,0,1
2
>2
HST≥ 81
SC
SC
SC
SC
SC
79 ≤ HST < 81
D1
D1
D2
D2
D2
75 ≤ HST < 79
SR
SR
D1
D2
D2
73≤ HST< 75
SR
SR
SR
D1
D1
71 ≤ HST ≤ 73
Norm
Norm
Norm
SR
SR
HST < 71
12.7.6
Norm
System Over Power Protection Only For DCI72/80
Delta PWR
Power
< -2000
[-2000,0)
0
(0,2000]
> 2000
PWR ≥ 2900
SC
SC
SC
SC
SC
3300≤PWR < 3500
2750≤PWR < 2900
D1
D1
D2
D2
D2
3100 ≤PWR < 3300
2600≤PWR < 2750
SR
SR
D1
D2
D2
3000≤PWR < 3100
2450≤PWR < 2600
2300 ≤PWR ≤
2450
PWR < 2300
SR
SR
SR
D1
D1
Norm
Norm
Norm
SR
SR
PWR1
PWR ≥ 3500
2950 ≤PWR ≤ 3000
PWR < 2950
PWR2
Norm
There are two sets of OVRPWR values, the selection of the values are set according to the state of
the Power-Shed input.
Power-Shed input open Set values 1
Power-Shed input sort Set values 2
12.7.7
Outdoor Coil Deicing Protection
12.7.7.1 Outdoor coil Deicing Protection For DCI50/60/72Z
► Entering Deicing Conditions
Deicing operation will start when either one of the following conditions exist:
Case 1: OCT < OAT – 8 AND TLD > DI
Case 2: OCT < OAT – 12 AND TLD > 30 minutes.
Case 3: OCT is Invalid AND TLD > DI
Case 4: Unit is just switched to STBY AND OCT < OAT – 8
Case 5: NLOAD = 0 AND OCT < OAT -8
Case 6: OCT<-19 AND TLD>60 minutes
All this condition will exist during 10 seconds
OCT – Outdoor Coil Temperature
OAT – Outdoor Air Temperature
TLD – Time from Last Deicing
DI – Deicing Interval (Time Interval Between Two Deicing)
Deicing interval time when compressor is first started in heat mode, is 10 minutes if OCT < -2, and
is 40 minutes in other cases.
Deicing interval time is changed (increased/ decreased in 10 minutes steps) as a function of deicing
time. If deicing time is shorter then former deicing time, the deicing interval time will be increased. If
deicing time is longer then former deicing time, the deicing interval time will be decreased.
12-10
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
Deicing Operation Procedure
►
OCT
12
0
T h re s h o ld
COMP
ON
T1
T2
DT
m a x. 1 2 m in u te s
D e ic e F re q C h R V
RV
HEAT
COOL
O FAN
T1
T3
T3
ON
OFF
EEV
E E V D e ic e rO p e n
Any
T1=60 secondes;T2=36 secondes;T3=6 secondes
12.7.7.2 Outdoor coil Deicing Protection For DCI72/80
Entering Deicing Conditions
Deicing operation will start when either one of the following conditions exist:
Case 1: OCT < OAT – 8 AND TLD > DI
Case 2: OCT < OAT – 12 AND TLD > 30 minutes.
Case 3: OCT is Invalid AND TLD > DI
Case 4: Unit is just switched to STBY AND OCT < OAT – 8
Case 5: NLOAD = 0 AND OCT < OAT - 8
Case 6: OAT is invalid AND OCT< 8 AND TLD > DI AND Compressor ON Time > 15 minutes
All this condition will exist during 400 seconds
OCT – Outdoor Coil Temperature
OAT – Outdoor Air Temperature
TLD – Time from Last Deicing
DI – Deicing Interval (Time Interval between Two Deicing)
Deicing interval time when compressor is first started in heat mode, is 10 minutes if OCT < -2, and
is 40 minutes in other cases.
Deicing interval time is changed (increased/ decreased in 10 minutes steps) as a function of deicing
time. If deicing time is shorter then former deicing time, the deicing interval time will be increased. If
deicing time is longer then former deicing time, the deicing interval time will be decreased.
►
SM SX DCI 1-A.3 GB
CONTENT
12-11
CONTROL SYSTEM
Deicing Operation Procedure
►
OCT
12
0
Threshold
COMP
ON
T1
T2
T1
max. 12 minutes
DT
HEAT
RV
T3
COOL
OFAN
T3
ON
OFF
EEVDeicerOpen
EEV
Any
T1=50 secondes;T2=36 secondes;T3=6 secondes
12.7.8
Condensate Water Over Flow Protection
Each of the pins P1, P2, P3 can have two options:
1 – When it is shorted with P4
0 – When it is not shorted to P4
►
Water Level Protection-1 level
P1
P2
P3
Level
Don’t care
Don’t care
1
Normal
Don’t care
Don’t care
0
Overflow
(*) 1- Pin P1, P2, or P3 is connected to P4.
0- Pin P1, P2 or P3 is not connected to P4.
12-12
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
Overflow when
unit is ON
Overflow
Water Level
Overflow when
unit is OFF
Normal
ON
OPER
LED
OFF
BLINK
ANY
NLOAD
NLOAD is
forced to 0
0
ON
PUMP
OFF
8 min
12.8
8 min
8 min
Indoor Unit Dry Contact
Indoor unit Dry contact has two alternative functions that are selected by J9.
Function
Contact=open
Contact=short
J9=open
Presence Detector
Connection
No limit
Force to STBY
J9=short
Power Shedding Function
No limit
Limit NLOAD
12.9
Operating the Unit from Mode Button
Forced operation allows to start, stop and operate in Cooling or Heating, in pre-set
temperature according to the following table:
Forced operation Mode
Pre-set Temperature
Cooling
20°C
Heating
28°C
SM SX DCI 1-A.3 GB
CONTENT
12-13
CONTROL SYSTEM
12.10
On Unit Controls and Indicators
12.10.1
Indoor Unit controller Controls and Indicatiors for All Models
Except for Floor/Ceiling model
During OFF, Fan, Cool, Heat, Dry, and Auto modes (for operation in other modes, see at the
relevant spec paragraph):
STAND BY
INDICATOR
1. Lights up when the Air Conditioner is connected to power
and ready to receive the R/C commands
OPERATION
INDICATOR
1. Lights up during operation.
2. Blinks for 300 msec., to announce that a R/C infrared
signal has been received and stored.
3. Blinks continuously during protections (according to the
relevant spec section).
TIMER INDICATOR
Lights up during Timer and Sleep operation.
FILTER INDICATOR
Lights up when Air Filter needs to be cleaned.
COOLING INDICATOR
Lights up when system is switched to Cool Mode by using the
Mode Switch on the unit.
HEATING INDICATOR
Lights up when system is switched Heat Mode by using the Mode
Switch on the unit.
Mode SWITCH
(COOL/HEAT/OFF)
Every short pressing , the next operation mode is selected, in this
order :
SB → Cool Mode → Heat Mode → SB → …
In long pressing system enters diagnostic mode.
For short pressing:
RESET / FILTER
SWITCH
When Filter LED is on - turn off the FILTER INDICATOR
after a clean filter has been reinstalled.
When Filter LED is off – enable/disable the buzzer
announcer, if selected.
In long pressing system enters set up mode (if in SB).
12.10.2
Outdoor Unit controller Indicatiors
Unit has three LED’s.
SB LED is ON when power is ON (230 VAC, even when no communication).
STATUS LED is ON when COMP is ON, and Blinks according to diagnostics mode definitions when
either fault or protection occurs.
FAULT LED Blinks according to diagnostics mode definitions when either fault or protection occurs.
12-14
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
12.11
Test Mode
12.11.1
Entering Test Mode
System can enter Test mode in two ways:
Automatically when the following conditions exists for 30 minutes continuously:
Mode = Cool, Set point = 16, Room temperature = 27(+1/−2), Outdoor temperature = 35(+2/-1)
Or
Mode = Heat, Set point = 30, Room temperature = 20±1, Outdoor temperature = 7±(+1/-2)
Manually when entering diagnostics with the following settings:
Mode = Cool, Set point = 16
Mode = Heat, Set point = 30
12.11.2
Unit Operation in Test Mode
In test mode, the unit will operate in fixed settings according to the indoor fan speed setting:
Indoor FAN Speed Setting
Unit Setting
Low
Minimum Capacity Setting
Turbo
Auto
Nominal Capacity Setting
Maximum Capacity Setting
During test mode, protections are disabled, except for stop compressor status.
12.12
SW Parameters
12.12.1
Indoor Units SW Parameters
Model dependent parametes - KN
Cap .Group
NomLoadC
NomLoadH
MaxNLOADIF1C
MaxNLOADIF2C
MaxNLOADIF3C
MaxNLOADIF4C
MaxNLOADIF5C
MinRTC
MaxNLOADRTC
MaxNLOADIF1H
MaxNLOADIF2H
MaxNLOADIF3H
MaxNLOADIF4H
MaxNLOADIF5H
MaxNLOADRTH
MaxRTH
MaxNLOADPSC
MaxNLOADPSH
SM SX DCI 1-A.3 GB
A
(KN-60)
3
81
77
55
70
127
127
127
20
127
127
127
127
127
127
127
27
81
77
B
(KN-72)
4
61
59
44
50
120
127
127
20
127
127
127
127
127
127
127
27
61
59
C
(KN-80)
4
67
67
85
102
120
127
127
20
127
127
127
127
127
127
127
27
67
67
CONTENT
12-15
CONTROL SYSTEM
Model dependent parameters - DNG
Unit
A
(DNG50)
B
(DNG60)
C
(DNG72)
D
(DNG80)
3
62
74
22
28
30
32
40
50
63
120
127
127
20
127
127
127
127
127
127
127
27
62
74
3
77
80
22
28
30
32
40
50
63
120
127
127
20
127
127
127
127
127
127
127
27
77
80
4
57
55
22
28
30
32
40
63
85
115
127
127
20
127
127
127
127
127
127
127
27
57
55
4
60
63
22
28
30
32
40
78
100
127
127
127
20
127
127
127
127
127
127
127
27
60
63
Cap .Group
NomLoadC
NomLoadH
ICTSTSpeed
ICTVLSpeed
ICTLSpeed
ICTHSpeed
ICTTSpeed
MaxNLOADIF1C
MaxNLOADIF2C
MaxNLOADIF3C
MaxNLOADIF4C
MaxNLOADIF5C
MinRTC
MaxNLOADRTC
MaxNLOADIF1H
MaxNLOADIF2H
MaxNLOADIF3H
MaxNLOADIF4H
MaxNLOADIF5H
MaxNLOADRTH
MaxRTH
MaxNLOADPSC
MaxNLOADPSH
Model dependent parameters - WNG
(WNG) Wall Mounted Models
Parameter name
25
35
50
60
72
80
NLOAD limits as a function of selected indoor fan speed
MaxNLOADIF1C
40
40
45
50
53
68
MaxNLOADIF2C
53
53
62
85
75
90
MaxNLOADIF3C
120
120
120
120
105
120
MaxNLOADIF4C
127
127
127
127
127
127
MaxNLOADIF5C
127
127
127
127
127
127
Indoor Fan speeds
IFVLOWC
700
700
700
800
850
850
IFLOWC
800
800
900
1000
1000
1000
IFMEDC
900
950
1050
1100
1150
1150
IFHIGHC
1050
1100
1200
1250
1350
1300
IFTURBOC
1150
1200
1250
1300
1400
1350
IFVLOWH
700
700
700
800
900
900
IFLOWH
800
850
900
950
1050
1050
IFMEDH
950
1000
1100
1150
1200
1200
IFHIGHH
1100
1150
1250
1250
1350
1300
IFTURBOH
1200
1250
1300
1300
1400
1350
12-16
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
Model dependent parameters - SX
A
(SX 18)
B
(SX 24)
C
(SX 30)
Cap .Group
3
NomLoadC
68
NomLoadH
77
MaxNLOADIF1C
40
MaxNLOADIF2C
60
MaxNLOADIF3C
90
MaxNLOADIF4C
90
MaxNLOADIF5C
90
MinRTC
20
MaxNLOADRTC
127
MaxNLOADIF1H
127
MaxNLOADIF2H
127
MaxNLOADIF3H
127
MaxNLOADIF4H
127
MaxNLOADIF5H
127
MaxNLOADRTH
127
MaxRTH
27
MaxNLOADPSC
68
MaxNLOADPSH
77
4
60
60
127
127
127
127
127
20
127
127
127
127
127
127
127
27
60
60
4
63
67
127
127
127
127
127
20
127
127
127
127
127
127
127
27
63
67
Unit
SM SX DCI 1-A.3 GB
CONTENT
12-17
CONTROL SYSTEM
12.12.2
Outdoor Units SW Parameters:
Model dependent parameters for DCI50/60
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
12-18
Name
MinFreqC
MaxFreqC
MinFreqH
MaxFreqH
NormAccel
NormDecel
Step1Freq
Step2Freq
Step3Freq
OFVL
OFLOWC
OFMEDC
OFMAXC
OFLOWH
OFMEDH
OFMAXH
OFANTESTMODEC
OFANTESTMODEH
OFDelTestMode
CTTOH1
CTTOH2
CTTOH3
CTTOH4
CCROC1
CCROC2
CCROC3
CCROC4
DEICT1
DEICT2
DEICT3
ProtFreqLimit
EEVDecierOpen
OptimDeicFreq
EEVMinOperOpenC
EEVMaxOperOpenC
EEVMinOperOpenH
EEVMaxOperOpenH
EEVNormRate
EEVHighRate
EEVMaxOpen
OFLowFreqC
OFMedFreqC
OFLowFreqH
OFMedFreqH
HeaterDisableFlag
DeiceFreqChRV
OATRefC
SUCT Enable
HST Enable
OAT Enable
OATRefH
MinTargCTTC
MaxTargCTTC
MinTargCTTH
MaxTargCTTH
DST
DSTF
OATLimitC
OATLimit1H
OATLimit2H
MaxFreqAsOATC
MaxFreqAsOAT1H
MaxFreqAsOAT2H
Single DCI-50
Single DCI 60
20
85
20
95
1
1
60
70
90
20
60
76
92
60
83
100
92
100
28
94
98
102
105
10
10.5
10.8
11.2
60
36
6
60
100
90
50
380
50
380
33
12
500
40
70
40
86
0
0
35
0
1
1
7
30
95
40
95
8
12
28
6
15
64
85
60
20
95
26
94
1
1
60
70
90
20
55
70
79
55
70
79
83
83
28
94
98
102
105
11.4
11.8
12.2
12.6
60
36
6
60
180
90
80
380
60
300
33
12
500
35
55
40
60
0
0
35
0
1
1
7
30
90
45
90
8
12
28
6
15
85
80
60
CONTENT
SM SX DCI 1-A.3 GB
CONTROL SYSTEM
Model dependent parameters for DCI72Z
No.
Name
Single
DCI-72Z
1
MinFreqC
15
2
MaxFreqC
70
3
MinFreqH
15
4
MaxFreqH
90
7
Step1Freq
35
8
Step2Freq
55
9
Step3Freq
90
10
OFMinRPM
8
11
OFMaxRPM
90
12
NightRPM
65
13
OFNNoiseMaxRPM
78
14
CTTOH1
90
15
CTTOH2
95
16
CTTOH3
100
17
CTTOH4
105
18
CCROC1
12.5
19
CCROC2
13.3
20
CCROC3
14.1
21
CCROC4
14.9
22
ProtFreqLimit
60
23
EEVMinOperOpenC
50
24
EEVMaxOperOpenC
480
25
EEVMinOperOpenH
50
26
EEVMaxOperOpenH
480
27
HeaterDisableFlag
0
28
HST Enable
1
29
OATLimitC
24
30
OATLimit1H
6
31
OATLimit2H
15
32
MaxFreqAsOATC
60
33
MaxFreqAsOAT1H
85
34
MaxFreqAsOAT2H
75
35
NormAccel
1
36
NormDecel
1
SM SX DCI 1-A.3 GB
CONTENT
12-19
CONTROL SYSTEM
Model dependent parameters for DCI72/80
Compressor Parameters
Value
MinOFFTime
3
MinOnTime
3
MaxCTT1
90
MaxCTT2
90
MinSpeedAsCTT1
26
MinSpeedAsCTT2
26
MaxSpeedC
75
MaxSpeedH
95
Step1RPS
40
Step2RPS
60
Step3RPS
75
NormAcc (sec/RPS)
1
NormDec (sec/RPS)
1
Down1(Sec/RPS)
12
Down2 (Sec/RPS)
7
DeiceAcc (Sec/RPS)
0.2
DeiceDec (Sec/RPS)
0.5
EEV Parameters
Value
NormEEVRate
30
EEVCompOFFOpen
200
EEVCompOFFTime
60
EEVMaxOpen
500
EEVMinOperOpenC
60
EEVMaxOperOpenC
500
EEVMinOperOpenH
70
EEVMaxOperOpenH
500
EEVMinOperOpenHInIDU
60
EEVMaxOperOpenHInIDU
140
EEVIDUOFFOpen
130
EEVMoveSteps
20
EEVTConstC
30
EEVTConstH
30
BlncTimTrnsStC
1
BlncTimStdyStC
1
BlncTimTrnsStH
1
BlncTimStdyStH
1
CompOffTimToTrnsSt
20
12-20
CONTENT
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.
EXPLODED VIEWS AND SPARE PARTS LISTS
13.1
Indoor Unit: SX 9, 12 DCI
SM SX DCI 1-A.3 GB
CONTENT
13-1
EXPLODED VIEWS AND SPARE PARTS LISTS
13.2
Indoor Unit: SX 9, 12 DCI
No
Part No
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
307979
382334
452731900
373247
455000600
323425
293321
452987400
4520158
4521029
372341
373245
221555
307981
484001
4525333
373244
371257
370281
375209-01
375209-05
375209-16
375209-17
4521827
4521831
372338
372339
263034
436665
391508
234213
391725
4521070
438413
438082
452935900
311036
Back panel
Base panel EPS
Evap. Assy SX25/35
Fan frame
Capacitor SX25/35
Motor support
Centrifugal fan
Transformer for SX25/35
Motor SX25/35
Spring clip
Fan cover
Left panel
Filter
Front panel
Air inlet assy
Motor connect wire for SX25/35
Right panel
Vertical louver
Air outlet
AIRWELL Display panel
WESPER Display panel
ELECTRA Display panel
JOHNSON Display panel
GORENJEN Display panel
FAGOR
Display panel
Horizontal louver front
Horizontal louver back
Swing motor
Stop motor
Connect wire
Display
Power cord without plug
Power cord (European plug)
Room sensor
Coil sensor
DCI STORM
Storm panel
20
21
22
23
24
25
26
27
28
29
30
13-2
CONTENT
Qty
1
1
1
1
1
1
2
1
1
2
2
1
2
1
1
1
1
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.3
Indoor Unit: SX 18, 24, 30 DCI
SM SX DCI 1-A.3 GB
CONTENT
13-3
EXPLODED VIEWS AND SPARE PARTS LISTS
13.4
Indoor Unit: SX 18 DCI
No
Part No
Description
1
307980
Back panel
1
2
382333
Base panel EPS
1
3
4527244
Evap. Assy SX18
1
4
373246
Fan frame
1
5
455000604
Capacitor SX18
1
6
453206900
Transformer
1
7
323422
Motor support
1
8
293322
Centrifugal fan
2
9
4520931
Motor Assy SX18,24
1
10
4521029
Spring clip
2
11
4525333
Motor connect wire
1
12
372340
Fan cover
2
13
373245
Left panel
1
14
221554
Filter
2
15
307982
Front panel
1
16
484002
Air inlet assy
1
17
373244
Right panel
1
18
371257
Vertical louver
12
19
370280
Air outlet
1
20
375209-16
ELECTRA
372336
Horizontal louver front
1
372337
Horizontal louver back
1
22
263034
Swing motor
1
23
436665
Step motor
1
24
391508
Connect wire
1
25
234213
Display
1
26
391726
Power cord 3x2.5
1
27
438082
Coil sensor
1
28
438413
Room sensor
1
29
452935900
DCI storm
1
30
311036
Storm panel
1
21
13-4
Display panel
CONTENT
Qty
1
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.5
Indoor Unit: SX 24, 30 DCI
No.
Part No.
Description
Qty
1
484002
Grille
1
2
221554
Air Filter
2
3
373244
Right panel
1
4
307982
Frame Asy
1
5
371071-72
Display panel
1
6
470680004
Evaporator Assy
1
7
370280
Air Outlet Assy
1
8
285032
Draining Hose
1
9
372336
Horizontal louver front
1
9
372337
Horizontal louver back
1
10
371255
Vert. Louver
12
11
372340
Fan cover
1
12
293322
Fan
1
13
307980
Back panel
1
14
466236
Installation Plate
1
15
382333
Base panel EPS
1
16
466100005
Motor
1
17
323422
Motor support
1
18
436665
Step Motor
1
18
263034
Swing motor
1
20
455000603
Capacitor
1
21
234213
Display
1
22
373246
Fan frame
1
23
452935900
DCI storm
1
24
438082
Thermistor indoor coil
1
25
438413
Thermistor
1
26
311036
Storm panel
1
27
391508
DConnect wire
1
29
436609R
Remote control
1
30
373245
Left panel
1
33
4521029
Spring clip
1
SM SX DCI 1-A.3 GB
CONTENT
13-5
EXPLODED VIEWS AND SPARE PARTS LISTS
20
21
22
23
24
25
26
27
29
28
30
40
13-6
42
41
38
37
36
35
1
2
3
4
34
5
6
7
8
9
33
32
39
Outdoor Unit: GC 9, 12 DCI
31
13.6
CONTENT
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.7
Outdoor Unit: GC 9, 12 DCI
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Part No.
433218
4526340
433223
4526476
4527092
433215
4523060
4526299
4526403
4524177
4524176
4526224
4526396
4526223
4526968
4526222
4526300
4526220
4526219
204107
4519188
433229
4522509
4526367
4526393
4518952
4518951
4526221
4526204
4526775
4526774
4526776
4526969
4526828
4526827
4519606
433228
4526368
4526298
4519614
4526480
4519300
433225
4519607
SM SX DCI 1-A.3 GB
Description
Front panel A
Air inlet ring-420
Painting insulation plate
Axial fan OD=401
DC motor for DCI25/35
Motor support
Base painting Assy.
Partition
Outdoor DC inverter controller (English)
Gas valve (R410A)
Liquid valve(R410A)
EMI fliter board 901-098-00
Chock Assy. 167-021-01
AC-IN connected wire
Earthing wire for DCI
Fuse connecting wire
Therminal sheet
Fuse stand JEF-511B(EHK P/N:150-038-00)
Fuse 65TS(15A,230)150-031-00
Cable clip nylon
4 poles terminal block
Value cover
4-Way valve coil
4-way valve welding Assy. (DCI25)
4-way valve welding Assy. (DCI35)
4-way valve (DCI25)
4-way valve (DCI35)
Compressor wire
DC Inverter compressor Assy. 5RS102XAB
Compressor top thermistor(CTT)
Outside air thermistor(OAT)
Outside coil thermistor(OCT)
Suction coil thermistor(SUCT)
EEV Coil (CAN-MD 12FKS-1 White)
Electronic expansion value (CAMB20YGFKS-1)
Right side panel
Back side net
Condenser soldering assy
Bridge
Painting top cover
Gasket for axial fan
Nut M5 L
Handle
Left side panel painting plate
CONTENT
Unit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
13-7
EXPLODED VIEWS AND SPARE PARTS LISTS
13.8
13-8
Outdoor Unit: GC 18 DCI
CONTENT
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.9
Outdoor Unit: GC 18 DCI
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Part No.
433218
4526340
433223
4526476
4526475
4526457
4527363
4526459
4526203
4524595
4524176
4526224
4526396
4526223
4526968
4526222
4526300
4526220
4526533
204107
4519188
433229
4522509
4527327
4518952
4526221
4523446
4526775
4526774
4526776
4526969
4526215
4526216
4519606
433228
4526459
4526298
4519614
4526480
4519300
433225
4519607
SM SX DCI 1-A.3 GB
Description
Front panel A
Air inlet ring-420
Painting insulation plate
Axial fan OD=401
DC motor for DCI 50
Motor support
Base painting Assy.
Partition
Outdoor DC inverter controller (English)
Gas valve (R410A)
Liquid valve(R410A)
EMI fliter board 901-098-00
Chock Assy. 167-021-01
AC-IN connected wire
Earthing wire for DCI
Fuse connecting wire
Therminal sheet
Fuse stand JEF-511B(EHK P/N:150-038-00)
Fuse 65TS(20A,230)150-031-00
Cable clip nylon
4 poles terminal block
Value cover
4-Way valve coil
4-way valve welding Assy.
4-way valve
Compressor wire
DC Inverter compressor Assy. 5CS130XCC03
Compressor top thermistor(CTT)
Outside air thermistor(OAT)
Outside coil thermistor(OCT)
Suction coil thermistor(SUCT)
Electronic expansion valve ZDPF(L)-1.6C-01-RK for R410A
EEV COIL QA(L)12-HR-01A-RK
Right side panel
Back side net
Condenser soldering assy
Bridge
Painting top cover
Gasket for axial fan
Nut M5 L
Handle
Left side panel painting plate
CONTENT
Unit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
13-9
EXPLODED VIEWS AND SPARE PARTS LISTS
13.10
13-10
Outdoor Unit: GC 24, 30 DCI
CONTENT
SM SX DCI 1-A.3 GB
EXPLODED VIEWS AND SPARE PARTS LISTS
13.11
Outdoor Unit: GC 24, 30 DCI
No.
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
465100000
4523652
4523758
452960400
461600002
452956700
4526522
452855600
4522601
4523653
452966200
452956500
452677601
452809900
452803300
452783600
452783200
453256100
4526080
4526513
4526514
4523654
4522602
4518950
467300005
204107
467420003
453138800
4526215
4526216
462300002
453175500
453083800
453256000
452809700
453170000
452888500
464250004
4526968
4526774
4523657
4522600
SM SX DCI 1-A.3 GB
Description
Outlet grid
PAINTED LEFT CABINET ASSY
Nut M8 left
OUTDOOR FAN
4-Way Valve Assy.
4-way valve coil
Four-Way Valve R410A
DC Resin Motor(EHD80A90EC/SIC-71FW-F170-1)
Right Handle
Painted Right Cabinet Assy.
Compressor Top Thermistor(CTT)
Suction Thermistor(SUCT)
Outdoor Coil Thermistor(OCT)
Base Plate Painting Assy.
Compressor Assy. TNB220FLBM1
Oil Separator Assy.
Liquid-Gas Separator
Support Painting Assy./Gas-Liquid Separator
Valve Plate Paint Assy.
Low Press Valve R410A
High Press Valve R410A
Painted Right Back Cabinet Assy.
Valve Cover
Filter Drier BFK-053S
Display Assy.(optional)
Cable clip Nylon
7 Poles Terminal Block
Terminal Plate
Electronic Expansion Valve ZDPF(L)-1.6C-01-RK
EEV COIL QA(L)12-MD-02
Condenser Assy.
Guard Net Painting Assy.
OAT Support
Choke Assy.
Partition Plate
Controller
Motor Support
Controller Connect Plate
Grounding wire with magnetic ring
Outdoor Air Thermistor(OAT)
Painted Top Cover Assy.
Left Handle
CONTENT
Unit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
13-11
APPENDIX A
APPENDIX A
INSTALLATION AND OPERATION MANUAL
►
OPERATION MANUAL SX 9, 12, 18, 24, 30 DCI
►
INSTALLATION MANUAL SX 9, 12, 18, 24, 30 DCI
SM SX DCI 1-A.3 GB
CONTENT
14-1
">