American DJ Tri Beam Instruction manual

American DJ
®
Tri Beam™ General Introduction
Introduction: Thank you for purchasing the American DJ® Tri Beam.™
The Tri Beam™ is a unique three color, three channel, DMX intelligent,
laser effect that creates different patterns. The unit uses eight internal mirrors to bounce the laser reflection over a wide area. This unit
can be used as a stand alone, sound-active unit or in a Master/Slave
configuration. The unit can also be controlled via DMX controller. The
unit’s sound sensitivity may be adjusted by a sensitivity adjustment on
the back of the unit. The unit may be mounted in either a horizontal or
vertical position.
Unpacking: Every Tri Beam™ has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If
the carton appears to be damaged, carefully inspect the unit for any
damage and be sure all accessories necessary to operate the unit
have arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return the unit to your dealer without
first contacting customer support.
Customer Support: American DJ® provides a toll free customer
support line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00
p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
User Instructions
Rev. 10/09
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact American DJ customer support.
PLEASE recycle the shipping carton whenever possible.
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 2
Tri Beam™ General Instructions
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Tri Beam™ •
•
•
•
•
•
Features
4.9mW Red and Green Laser Diodes
3 Laser Colors (Red and Green combine to make Yellow)
Built-In Hanging Yoke
Sound Active with Internal Microphone
Audio Sensitivity Knob
2 Operating Modes: DMX Control & Stand Alone
Tri Beam™
Warranty Registration
The Tri Beam™ carries a 90 day limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. If the unit is under
warranty you must provide a copy of your proof of purchase invoice.
Please contact American DJ® customer support for a R.A. number.
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 3
Tri Beam™ !
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to operate this unit if the power cord has been frayed or broken.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 9 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 4
Tri Beam™ Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Tri Beam™ contains high power laser devices internally. Do not
open the laser housing, due to the potential exposure to unsafe levels
of laser radiation. The laser power levels, if the unit is opened, can
cause instant blindness, skin burns and fires.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
Tri Beam™ Laser Warnings and Safety
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diffraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very different from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
floor.
Do not operate the laser without first reading and understanding
all safety and technical data in this manual.
Do not point lasers at highly reflective surfaces, such as windows,
mirrors and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Never open the laser housing. The high laser power levels inside of
the protective housing can start fires, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
effects overhead.
Always set up and install all laser effects so that all laser light is at
least 3 meters (9.8 feet) above the floor on which people can stand.
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 5
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 6
Tri Beam™ Laser Warning Labels
Tri Beam™ Control & Functions
1
6
2
3
5
4
1.XLR Output Jack - This jack is used to transmit the incoming
DMX s ignal to another DMX fixture, or transmit a Master/Slave signal
to the next Tri Beam™ in the chain. For best results in DMX or Master/
Slave mode terminate this jack if it is the last unit in the chain. See
“Terminator” on page 9.
2. Power Switch - Switches the power on or off.
3. DC Input - Accepts a DC 9V, 500 mA minimum, power supply.
4.Audio Sensitivity Knob - This adjust audio sensitivity of the internal microphone. Turning the sensitivity knob in the clockwise direction
will increase the sensitivity to sound. Turning the knob in the counter
clockwise direction will decrease the fixture’s sensitivity to sound. If
the knob is turned completely in the counter-clockwise direction the
sound sensitivity function will turn off.
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 7
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 8
Tri Beam™ Control & Functions
Tri Beam™ Set Up
5.Dipswitches - These switches serve two functions. In master-slave
mode these switches are used to assign a specific head address. In
DMX mode these switches are used to assign a DMX address to the
unit. In DMX mode each switch corresponds to a specific value based
on binary code. See page 7 for a detailed explanation of DMX binary
code.
Power Supply: Before plugging your unit in, be sure the source volt-
6.XLR Input Jack - This jack is used to accept an incoming DMX
signal or Master/Slave signal.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
Tri Beam™ Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external lenses should be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output.
age in your area matches the required voltage for your American DJ®
Tri Beam.™ The American DJ® Tri Beam™ is 120v only. Because line
voltage may vary from venue to venue, you should be sure your unit
voltage matches the wall outlet voltage before attempting to operate
you fixture.
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Dipswitches in DMX mode: This unit uses dipswitches to assign a
DMX address. Each dipswitch represents a binary value.
Dipswitch 1 address equals 1
Dipswitch 2 address equals 2
Dipswitch 3 address equals 4
Dipswitch 4 address equals 8
Dipswitch 5 address equals 16
Dipswitch 6 address equals 32
Dipswitch 7 address equals 64
Dipswitch 8 address equals 128
Dipswitch 9 address equals 256
Dipswitch 10 - Some units omit dipswitch 10. When a unit does
include dipswitch #10, it is usually used for special functions such as
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 9
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 10
Tri Beam™ Set Up
Tri Beam™ sound activation.
Assigning DMX Address: Each dipswitch has a preset value. A specific DMX address is set by combining the dipswitches that sum your
desired value. For example: To achieve a DMX address of 7, combine
dipswitches 1, 2, and 3. Since dipswitch 1 has a value of 1, dipswitch
2 has a value of 2, and dipswitch 3 has a value of 4, the combination
of the three create a DMX value of 7. (See example below).
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
2
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
INPUT
POWER
3
OUTPUT
SOUND
POWER
DMX+,DMX-,COMMON
cables. Do not
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 OUT
3-PIN XLR
1
2
3
DMX +
DMX -
3
1
2
DMX512 IN
3-PIN XLR
3
Figure 1
©American
1
2
OUTPUT
REMOTE
SOUND
3 Hot
Pin 1 = Ground
INPUT
OUTPUT
PinCONTROL
2
= Data Compliment (negative)
INPUT
3 Hot
Pin 3 = Data True (positive)
Figure 2
Special Note: Line Termination. When longer runs of cable are
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR socket of the last unit
in your daisy chain to terminate the line. Using a cable terminator (ADJ
part number Z-DMX/T) will decrease the possibilities of erratic behavior.
3
1
2
DMX512 IN
3-PIN XLR
3
REMOTE
CONTROL
INPUT
INPUT
1
2
OUTPUT
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 3
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
POWER
Notice: Be sureDMX512
to follow figures one and two when making your own
COMMON
INPUT
XLR Pin Configuration
1 Ground
POWER
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Tri Beam™ can be controlled via DMX-512 protocol.
The Tri Beam™ is a three channel DMX unit. The DMX addressCOMMON
is set
on the back panel of the Tri Beam.™ Your unit DMX512
and your
DMX
controlDMX +
OUT
XLR input and DMX
ler require a standard 3-pin XLR connector for3-PIN
data
data
output (Figure 1). If you are making your own cables, be sure to use
standard two conductor shielded cable (This cable may be purchased
at almost all pro sound and lighting stores). Your cables should be
made with a male and female XLR connector on either end of the
cable. Also remember that DMX cable must be daisy chained and can
not be split.
1
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
Set DMX address 1:
Set DMX address 7:
POWER
Dip-switches # 1 = 1
Dip-switches # 1 = 1
2=2
3 DMX512
=4
DMX+,DMX-,COMMON
=7
SOUND
XLR Female Socket
XLR Male Socket
1 Ground
Set Up
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Pin 3
Pin 3
Termination reduces signal errors and
Data True (+ signal)
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
Not Used
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 11
Not Used
©American
Pin 4 - Do Not Use
Pin 5 - Do Not Use
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 12
Tri Beam™ Operation
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Power Supply: This unit is available only in 120v. Before plugging
your unit in be sure the source voltage in your area matches the
required voltage for your American DJ® Tri Beam.™
General Operation: This fixture is designed to operate as a stand
alone, sound-active unit, or in a Master/Slave configuration. It can
also operate via DMX controller. The Tri Beam™ is ready to be
plugged in out of the box. After plugging the power supply into a
power outlet the lasers will immediately begin to cycle through the
many built in patterns (provided all dipswitch are in the “OFF” position, and there is an ample amount of sound to trigger the unit). You
can also flip dipswitch #10 to the “ON” poition to activate the Auto
Mode. The unit comes with several built-in patterns that automatically
cycle through when the unit is operating.
Sensitivity Knob: A sound sensitivity knob is located on the rear
of the unit. Use this knob to regulate the amount of sound it takes to
trigger the unit. Turning the knob in a clockwise direction will increase
the units sensitivity to sound, turning the knob in a counterclockwise direction will decrease the units sensitivity. Turning the knob
completely to the counter-clockwise direction will turn off the soundactive mode.
Operating Modes:
Universal DMX Control: This mode allows you to use a universal
DMX-512 controller such as the American DJ® DMX Operator™ or
Show Designer.™
1. To control your fixture in DMX mode, follow the set-up procedures
on pages 10-12 as well as the set-up procedures included with
your DMX controller.
2. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
3. Assign a DMX address to the unit by following the dipswitch chart
on page 18.
4. The Tri Beam™ uses three DMX channels. See pages 16-17 for
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 13
Tri Beam™ 5.
Operation
detailed description of the DMX traits. Use your DMX controller to activate the various built-in patterns.
For help operating in DMX mode consult the manual included with your DMX controller.
NOTE: If running in Master/Slave configuration while using a DMX controller, the Master unit should have all dipswitches set to the “OFF” position. All slave units should have dipswitch #1 set to the “ON” position.
Stand-Alone Operation (Sound Active): This mode allows a
single unit to run to the beat of the music. Only use this mode when
running a single unit, or when running several units as individuals.
1. Set all dipswitches to the “OFF” positon to activate Sound Active. 2. The unit will react to the low frequencies of music via the internal microphone.
3. Use the audio sensitivity knob on the side of the unit to make
the unit more or less sensitive to sound. Turning the sensitivity knob
in the clockwise direction will increase the sensitivity, turning the knob in the counter-clockwise direction will decrease the fixture’s sensitivity to sound.
Master-Slave Operation (Sound Active): This mode will allow
you to link up to 16 units together and operate without a controller.
In Master-Slave mode, the units will react to sound. In Master-Slave
operation one unit will act as the controlling unit and the others will
react to the controlling units programs. Any unit can act as a Master
or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. For longer cable runs we suggest a terminator at the last fixture.
2. Choose a unit to function as the Master and set dipswitch #11 to the “ON” position. This unit must be the first unit in line. Then simply daisy chain the units together using XLR cables.
3. Turn dipswitch #1 to the “ON” position on the SLAVE units, and they will react the same as the MASTER.
4. Use the sensitivity knob on the back of the master unit to make
it more or less sensative to sound. (See sensitivity knob on page 8.)
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 14
Tri Beam™ 1
2
3
4
5
6
7
8
9 10 11 12
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SET DMX ADDRESS
X
X
X
X
X
X
X
X
X
O = ON
X = OFF
Channel
X
X
X
X
SOUND ACTIVE
O
X
MASTER
X
X
X
SLAVE
X
X
X
DMX MODE
X
X
O
TEST MODE
X
O
SET TO SOUND/AUTO MODE
X
Tri Beam™ 1
FUNCTION
DIPSWITCH CHART
O
Dipswitch Chart
Value
0 - 255
0
1 - 13
14 - 26
27 - 39
40 - 52
53 - 65
66 - 78
79 - 91
92 - 104
105 - 117
118 - 130
131 - 143
144 - 156
157 - 169
170 - 182
AUTO MODE
183 - 195
196 - 208
209 - 232
233 - 255
2
0 - 255
0 - 200
201 - 212
213 - 215
216 - 227
228 - 255
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 15
©American
DMX Traits
Function
COLORS AND LINE SELECTION
OFF
RED LINE
GREEN LINE
YELLOW LINE
RED DOTTED LINE 1
GREEN DOTTED LINE 1
YELLOW DOTTED LINE 1
RED + GREEN LINE
RED DOTTED LINE 2
GREEN DOTTED LINE 2
YELLOW DOTTED LINE 2
RED + GREEN LINE 2
RED + YELLOW LINE 2
GREEN + YELLOW LINE 2
RED + GREEN + YELLOW
DOTTED LINE
RED + GREEN + YELLOW LINE 1
RED + GREEN + YELLOW LINE 2
COLOR AND LINES CHANGE
EVERY 3 SEC.
COLOR AND LINES CHANGE EVERY 5 SEC.
LASER MOVEMENT UP AND DOWN
LASER POSITION SELECTION
LASER CONTINUOUSLY MOVES UPWARDS
STOP
LASER CONTINUOUSLY MOVES DOWNWARDS
SOUND ACTIVE
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 16
Tri Beam™ Channel
3
Value
DMX Traits
Function
0 - 255
CHANNEL 3 IS FUNCTIONAL ONLY
WHEN THE VALUE OF CHANNEL 2
IS BETWEEN 0 -200
0 - 55
NOT USED
Tri Beam™ DMX Address Chart
This chart list the DMX dipswitch setting for DMX address 1 through
511. Follow the instructions below to configure fixture dipswitches
with your desired DMX address.
56
x4 TIMES
x3 TIMES
x2 TIMES
x1 TIME
STARTING POINT
x1 TIME
x2 TIMES
x3 TIMES
255
©American
x4 TIMES
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 17
©American
DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 18
Tri Beam™ Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
Tri Beam™ Specifications
Model: Tri Beam™
Voltage*:
Power Supply:
Lasers:
Dimensions:
Weight:
Duty Cycle:
Ventilation:
Warranty:
120v/230v~56Hz/60Hz
UL or CE Adapter DC 12V 1000MA
4.9mW Red and Green Diodes
5.5” (H) x 4.7” (W) x 19.6” (L)
8.8 Lbs. (4kg)
None
Fan Cooled
90 Days
*Voltage is preset at the factory and can not be changed by the user.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
©American DJ® - www.americandj.com - Tri Beam™ Instruction Manual Page 19
American DJ®
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com