Endres+Hauser BA Proline Prosonic Flow I 400 Operating Instruction
PDF
Download
Document
Advertisement
Advertisement
BA02303D/06/EN/01.24-00 71645358 2024-05-15 Products Solutions Valid as of version 01.00.zz (Device firmware) Operating Instructions Proline Prosonic Flow I 400 Ultrasonic time-of-flight flowmeter Modbus RS485 Services Proline Prosonic Flow I 400 Modbus RS485 • Make sure the document is stored in a safe place such that it is always available when working on or with the device. • To avoid danger to individuals or the facility, read the "Basic safety instructions" section carefully, as well as all other safety instructions in the document that are specific to working procedures. • The manufacturer reserves the right to modify technical data without prior notice. Your Endress+Hauser sales organization will supply you with current information and updates to this manual. 2 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Table of contents Table of contents 1 About this document . . . . . . . . . . . . . . . . 6 1.1 1.2 1.3 1.4 Document function . . . . . . . . . . . . . . . . . . . . . 6 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.2.1 Safety symbols . . . . . . . . . . . . . . . . . . 6 1.2.2 Electrical symbols . . . . . . . . . . . . . . . . 6 1.2.3 Communication-specific symbols . . . . . 6 1.2.4 Tool symbols . . . . . . . . . . . . . . . . . . . . 7 1.2.5 Symbols for certain types of information . . . . . . . . . 7 1.2.6 Symbols in graphics . . . . . . . . . . . . . . . 7 Documentation . . . . . . . . . . . . . . . . . . . . . . . . 8 Registered trademarks . . . . . . . . . . . . . . . . . . . 8 2 Safety instructions . . . . . . . . . . . . . . . . . . 9 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Requirements for the personnel . . . . . . . . . . . . 9 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Workplace safety . . . . . . . . . . . . . . . . . . . . . . 10 Operational safety . . . . . . . . . . . . . . . . . . . . . 10 Product safety . . . . . . . . . . . . . . . . . . . . . . . . 10 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Device-specific IT security . . . . . . . . . . . . . . . . 10 2.7.1 Protecting access via hardware write protection . . . . . . . . . . . . . . . . . . . . . 11 2.7.2 Protecting access via a password . . . . 11 2.7.3 Access via web server . . . . . . . . . . . . 12 2.7.4 Access via service interface (CDIRJ45) . . . . . . . . . . . . . . . . . . . . . . . . 12 3 Product description . . . . . . . . . . . . . . . . 13 3.1 Product design . . . . . . . . . . . . . . . . . . . . . . . . 14 4 Incoming acceptance and product identification . . . . . . . . . . . . . . . . . . . . . 15 4.1 4.2 Incoming acceptance . . . . . . . . . . . . . . . . . . . 15 Product identification . . . . . . . . . . . . . . . . . . . 15 4.2.1 Transmitter nameplate . . . . . . . . . . . 16 4.2.2 Sensor nameplate . . . . . . . . . . . . . . . 16 4.2.3 Symbols on the device . . . . . . . . . . . . 17 5 Storage and transport . . . . . . . . . . . . . 18 5.1 5.2 5.3 Storage conditions . . . . . . . . . . . . . . . . . . . . . 18 Transporting the product . . . . . . . . . . . . . . . . 18 5.2.1 Transporting with a fork lift . . . . . . . . 18 Packaging disposal . . . . . . . . . . . . . . . . . . . . . 18 6 Mounting procedure . . . . . . . . . . . . . . . 19 6.1 Mounting requirements . . . . . . . . . . . . . . . . . 19 6.1.1 Mounting position . . . . . . . . . . . . . . . 19 6.1.2 Sensor set selection and arrangement . . . . . . . . . . . . . . . . . . . 22 Endress+Hauser 6.1.3 6.3 Environmental and process requirements . . . . . . . . . . . . . . . . . . 6.1.4 Special mounting instructions . . . . . . Mounting the measuring device . . . . . . . . . . . 6.2.1 Required tools . . . . . . . . . . . . . . . . . . 6.2.2 Preparing the measuring device . . . . . 6.2.3 Mounting the sensor . . . . . . . . . . . . . 6.2.4 Mounting the transmitter . . . . . . . . . 6.2.5 Turning the display module . . . . . . . . Post-mounting check . . . . . . . . . . . . . . . . . . . 7 Electrical connection . . . . . . . . . . . . . . 34 7.1 7.2 7.7 Electrical safety . . . . . . . . . . . . . . . . . . . . . . . 34 Connecting requirements . . . . . . . . . . . . . . . . 34 7.2.1 Required tools . . . . . . . . . . . . . . . . . . 34 7.2.2 Requirements for connecting cable . . . 34 7.2.3 Terminal assignment . . . . . . . . . . . . . 35 7.2.4 Shielding and grounding . . . . . . . . . . 36 7.2.5 Preparing the measuring device . . . . . 36 Connecting the measuring device . . . . . . . . . . 37 7.3.1 Connecting the sensor with transmitter . . . . . . . . . . . . . . . . . . . . 37 7.3.2 Connecting the transmitter . . . . . . . . 39 7.3.3 Potential equalization . . . . . . . . . . . . 39 Special connection instructions . . . . . . . . . . . . 40 7.4.1 Connection examples . . . . . . . . . . . . . 40 Hardware settings . . . . . . . . . . . . . . . . . . . . . 40 7.5.1 Activating the terminating resistor . . 40 Ensuring the degree of protection . . . . . . . . . . 40 7.6.1 Degree of protection IP66/67, Type 4X enclosure . . . . . . . . . . . . . . . . . . . 40 Post-connection check . . . . . . . . . . . . . . . . . . 41 8 Operation options . . . . . . . . . . . . . . . . . 42 8.1 8.2 Overview of operation methods . . . . . . . . . . . 42 Structure and function of the operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8.2.1 Structure of the operating menu . . . . 43 8.2.2 Operating philosophy . . . . . . . . . . . . 44 Access to operating menu via local display . . . 45 8.3.1 Operational display . . . . . . . . . . . . . . 45 8.3.2 Navigation view . . . . . . . . . . . . . . . . 47 8.3.3 Editing view . . . . . . . . . . . . . . . . . . . 48 8.3.4 Operating elements . . . . . . . . . . . . . . 50 8.3.5 Opening the context menu . . . . . . . . . 51 8.3.6 Navigating and selecting from list . . . 52 8.3.7 Calling the parameter directly . . . . . . 52 8.3.8 Calling up help text . . . . . . . . . . . . . . 53 8.3.9 Changing the parameters . . . . . . . . . 54 8.3.10 User roles and related access authorization . . . . . . . . . . . . . . . . . . 55 8.3.11 Disabling write protection via access code . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.2 7.3 7.4 7.5 7.6 8.3 23 24 24 24 25 25 30 32 32 3 Table of contents 8.4 8.5 8.3.12 Enabling and disabling the keypad lock . . . . . . . . . . . . . . . . . . . . . . . . . 56 Access to operating menu via web browser . . . 56 8.4.1 Function range . . . . . . . . . . . . . . . . . 56 8.4.2 Requirements . . . . . . . . . . . . . . . . . . 57 8.4.3 Connecting the device . . . . . . . . . . . . 58 8.4.4 Logging on . . . . . . . . . . . . . . . . . . . . 60 8.4.5 User interface . . . . . . . . . . . . . . . . . . 61 8.4.6 Disabling the Web server . . . . . . . . . . 62 8.4.7 Logging out . . . . . . . . . . . . . . . . . . . . 62 Access to the operating menu via the operating tool . . . . . . . . . . . . . . . . . . . . . . . . 62 8.5.1 Connecting the operating tool . . . . . . 63 8.5.2 FieldCare . . . . . . . . . . . . . . . . . . . . . 65 8.5.3 DeviceCare . . . . . . . . . . . . . . . . . . . . 66 8.5.4 Field Xpert SMT70, SMT77 . . . . . . . . 66 9 System integration . . . . . . . . . . . . . . . . 68 9.1 Overview of device description files . . . . . . . . . 68 9.1.1 Current version data for the device . . . 68 9.1.2 Operating tools . . . . . . . . . . . . . . . . . 68 Compatibility with previous model . . . . . . . . . 68 Modbus RS485 information . . . . . . . . . . . . . . 69 9.3.1 Function codes . . . . . . . . . . . . . . . . . 69 9.3.2 Register information . . . . . . . . . . . . . 70 9.3.3 Response time . . . . . . . . . . . . . . . . . . 70 9.3.4 Data types . . . . . . . . . . . . . . . . . . . . . 70 9.3.5 Byte transmission sequence . . . . . . . . 71 9.3.6 Modbus data map . . . . . . . . . . . . . . . 71 9.2 9.3 10 Commissioning . . . . . . . . . . . . . . . . . . . . 74 10.1 Post-mounting and post-connection check . . . 74 10.2 Switching on the measuring device . . . . . . . . . 74 10.3 Setting the operating language . . . . . . . . . . . . 74 10.4 Configuring the measuring device . . . . . . . . . . 74 10.4.1 Setting the system units . . . . . . . . . . 81 10.4.2 Configuring the communication interface . . . . . . . . . . . . . . . . . . . . . . 82 10.4.3 Configuring the measuring point . . . . 83 10.4.4 Checking the installation status . . . . . 88 10.4.5 Configuring the current output . . . . . 89 10.4.6 Configuring the pulse/frequency/ switch output . . . . . . . . . . . . . . . . . . 90 10.4.7 Configuring the relay output . . . . . . . 96 10.4.8 Configuring the double pulse output . . 98 10.4.9 Configuring the local display . . . . . . . 99 10.4.10 Configuring the low flow cut off . . . . 101 10.5 Advanced settings . . . . . . . . . . . . . . . . . . . . 103 10.5.1 Using the parameter to enter the access code . . . . . . . . . . . . . . . . . . . 104 10.5.2 Carrying out a sensor adjustment . . . 104 10.5.3 Configuring the totalizer . . . . . . . . . 104 10.5.4 Carrying out additional display configurations . . . . . . . . . . . . . . . . . 106 10.5.5 WLAN configuration . . . . . . . . . . . . 108 10.5.6 Performing Heartbeat basic setup . . 110 10.5.7 Using parameters for device administration . . . . . . . . . . . . . . . . 111 4 Proline Prosonic Flow I 400 Modbus RS485 10.6 10.7 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Protecting settings from unauthorized access 114 10.7.1 Write protection via access code . . . 114 10.7.2 Write protection via write protection switch . . . . . . . . . . . . . . . . . . . . . . . 116 11 Operation . . . . . . . . . . . . . . . . . . . . . . . 117 11.1 Reading off the device locking status . . . . . . 117 11.2 Adjusting the operating language . . . . . . . . . 117 11.3 Configuring the display . . . . . . . . . . . . . . . . 117 11.4 Reading off measured values . . . . . . . . . . . . 117 11.4.1 Process variables . . . . . . . . . . . . . . . 118 11.4.2 System values . . . . . . . . . . . . . . . . . 119 11.4.3 Input values . . . . . . . . . . . . . . . . . . 119 11.4.4 Output values . . . . . . . . . . . . . . . . . 120 11.4.5 "Totalizer" submenu . . . . . . . . . . . . . 121 11.5 Adapting the measuring device to the process conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 121 11.6 Performing a totalizer reset . . . . . . . . . . . . . 122 11.6.1 Function scope of "Control Totalizer" parameter . . . . . . . . . . . . . . . . . . . . 122 11.6.2 Function range of "Reset all totalizers" parameter . . . . . . . . . . . . 123 11.7 Displaying the measured value history . . . . . 123 12 Diagnosis and troubleshooting . . . . 126 12.1 General troubleshooting . . . . . . . . . . . . . . . . 126 12.2 Diagnostic information via light emitting diodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 12.2.1 Transmitter . . . . . . . . . . . . . . . . . . . 127 12.3 Diagnostic information on local display . . . . . 129 12.3.1 Diagnostic message . . . . . . . . . . . . . 129 12.3.2 Calling up remedial measures . . . . . 131 12.4 Diagnostic information in the web browser . . 131 12.4.1 Diagnostic options . . . . . . . . . . . . . . 131 12.4.2 Calling up remedy information . . . . 132 12.5 Diagnostic information in FieldCare or DeviceCare . . . . . . . . . . . . . . . . . . . . . . . . . 132 12.5.1 Diagnostic options . . . . . . . . . . . . . . 132 12.5.2 Calling up remedy information . . . . 133 12.6 Diagnostic information via communication interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 12.6.1 Reading out diagnostic information 134 12.6.2 Configuring error response mode . . . 134 12.7 Adapting the diagnostic information . . . . . . 134 12.7.1 Adapting the diagnostic behavior . . . 134 12.8 Overview of diagnostic information . . . . . . . 135 12.9 Pending diagnostic events . . . . . . . . . . . . . . 138 12.10 Diagnostics list . . . . . . . . . . . . . . . . . . . . . . 139 12.11 Event logbook . . . . . . . . . . . . . . . . . . . . . . . 139 12.11.1 Reading out the event logbook . . . . . 139 12.11.2 Filtering the event logbook . . . . . . . 140 12.11.3 Overview of information events . . . . 140 12.12 Resetting the measuring device . . . . . . . . . . 141 12.12.1 Function range of "Device reset" parameter . . . . . . . . . . . . . . . . . . . . 142 12.13 Device information . . . . . . . . . . . . . . . . . . . 142 12.14 Firmware history . . . . . . . . . . . . . . . . . . . . . 144 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 13 Maintenance . . . . . . . . . . . . . . . . . . . . 145 13.1 13.2 13.3 Maintenance tasks . . . . . . . . . . . . . . . . . . . . 145 13.1.1 Exterior cleaning . . . . . . . . . . . . . . . 145 Measuring and test equipment . . . . . . . . . . . 145 Endress+Hauser services . . . . . . . . . . . . . . . 145 14 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 14.1 General notes . . . . . . . . . . . . . . . . . . . . . . . 146 14.1.1 Repair and conversion concept . . . . . 146 14.1.2 Notes for repair and conversion . . . . 146 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . 146 Endress+Hauser services . . . . . . . . . . . . . . . 146 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 14.5.1 Removing the measuring device . . . . 147 14.5.2 Disposing of the measuring device . . 147 14.2 14.3 14.4 14.5 15 Table of contents Accessories . . . . . . . . . . . . . . . . . . . . . . 148 15.1 Device-specific accessories . . . . . . . . . . . . . . 148 15.1.1 For the transmitter . . . . . . . . . . . . . 148 15.1.2 For the sensor . . . . . . . . . . . . . . . . . 148 15.2 Communication-specific accessories . . . . . . . 149 15.3 Service-specific accessories . . . . . . . . . . . . . . 150 15.4 System components . . . . . . . . . . . . . . . . . . . 150 16 Technical data . . . . . . . . . . . . . . . . . . . 151 16.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . 151 16.2 Function and system design . . . . . . . . . . . . . 151 16.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 16.4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 16.5 Power supply . . . . . . . . . . . . . . . . . . . . . . . . 155 16.6 Performance characteristics . . . . . . . . . . . . . 157 16.7 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 159 16.8 Environment . . . . . . . . . . . . . . . . . . . . . . . . 160 16.9 Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 16.10 Mechanical Construction . . . . . . . . . . . . . . . 161 16.11 Display and user interface . . . . . . . . . . . . . . 163 16.12 Certificates and approvals . . . . . . . . . . . . . . 166 16.13 Application packages . . . . . . . . . . . . . . . . . . 167 16.14 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 168 16.15 Supplemental documentation . . . . . . . . . . . . 168 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Endress+Hauser 5 About this document Proline Prosonic Flow I 400 Modbus RS485 1 About this document 1.1 Document function These Operating Instructions contain all the information required in the various life cycle phases of the device: from product identification, incoming acceptance and storage, to installation, connection, operation and commissioning, through to troubleshooting, maintenance and disposal. 1.2 Symbols 1.2.1 Safety symbols DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious or fatal injury. WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or fatal injury. CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor or medium injury. NOTICE This symbol contains information on procedures and other facts which do not result in personal injury. 1.2.2 Electrical symbols Symbol Meaning Direct current Alternating current Direct current and alternating current Ground connection A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system. Potential equalization connection (PE: protective earth) Ground terminals that must be connected to ground prior to establishing any other connections. The ground terminals are located on the interior and exterior of the device: • Interior ground terminal: potential equalization is connected to the supply network. • Exterior ground terminal: device is connected to the plant grounding system. 1.2.3 Communication-specific symbols Symbol Meaning Wireless Local Area Network (WLAN) Communication via a wireless, local network. Bluetooth Wireless data transmission between devices over a short distance. LED Light emitting diode is off. 6 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Symbol About this document Meaning LED Light emitting diode is on. LED Light emitting diode is flashing. 1.2.4 Tool symbols Symbol Meaning Torx screwdriver Phillips head screwdriver Open-ended wrench 1.2.5 Symbols for certain types of information Symbol Meaning Permitted Procedures, processes or actions that are permitted. Preferred Procedures, processes or actions that are preferred. Forbidden Procedures, processes or actions that are forbidden. Tip Indicates additional information. Reference to documentation Reference to page A Reference to graphic Notice or individual step to be observed 1. , 2. , 3. … Series of steps Result of a step Help in the event of a problem Visual inspection 1.2.6 Symbols in graphics Symbol Meaning 1, 2, 3, ... Item numbers 1. , 2. , 3. , … Series of steps A, B, C, ... Views A-A, B-B, C-C, ... Sections Endress+Hauser Hazardous area 7 About this document Proline Prosonic Flow I 400 Modbus RS485 Symbol . Meaning Safe area (non-hazardous area) Flow direction 1.3 Documentation For an overview of the scope of the associated Technical Documentation, refer to the following: • Device Viewer (www.endress.com/deviceviewer): Enter the serial number from the nameplate • Endress+Hauser Operations app: Enter serial number from nameplate or scan matrix code on nameplate. The following documentation may be available depending on the device version ordered: Document type Purpose and content of the document Technical Information (TI) Planning aid for your device The document contains all the technical data on the device and provides an overview of the accessories and other products that can be ordered for the device. Brief Operating Instructions (KA) Guide that takes you quickly to the 1st measured value The Brief Operating Instructions contain all the essential information from incoming acceptance to initial commissioning. Operating Instructions (BA) Your reference document These Operating Instructions contain all the information that is required in the various life cycle phases of the device: from product identification, incoming acceptance and storage, to mounting, connection, operation and commissioning, through to troubleshooting, maintenance and disposal. Description of Device Parameters (GP) Reference for your parameters The document provides a detailed explanation of each individual parameter. The description is aimed at those who work with the device over the entire life cycle and perform specific configurations. Safety Instructions (XA) Depending on the approval, safety instructions for electrical equipment in hazardous areas are also supplied with the device. The Safety Instructions are a constituent part of the Operating Instructions. on the Safety Instructions (XA) that are relevant for Information the device is provided on the nameplate. Supplementary device-dependent documentation (SD/FY) 1.4 Always comply strictly with the instructions in the relevant supplementary documentation. The supplementary documentation is a constituent part of the device documentation. Registered trademarks Modbus® Registered trademark of SCHNEIDER AUTOMATION, INC. 8 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 2 Safety instructions 2.1 Requirements for the personnel Safety instructions The personnel for installation, commissioning, diagnostics and maintenance must fulfill the following requirements: ‣ Trained, qualified specialists must have a relevant qualification for this specific function and task. ‣ Are authorized by the plant owner/operator. ‣ Are familiar with federal/national regulations. ‣ Before starting work, read and understand the instructions in the manual and supplementary documentation as well as the certificates (depending on the application). ‣ Follow instructions and comply with basic conditions. The operating personnel must fulfill the following requirements: ‣ Are instructed and authorized according to the requirements of the task by the facility's owner-operator. ‣ Follow the instructions in this manual. 2.2 Intended use Application and media The measuring device described in this manual is intended only for the flow measurement of liquids. Depending on the version ordered, the measuring device can also measure potentially explosive, flammable, poisonous and oxidizing media. Measuring devices for use in explosive atmospheres, in hygienic applications or where there is a high risk of pressures, are labeled accordingly on the nameplate. To ensure that the measuring device is in proper condition during the operation period: ‣ Only use the measuring device in full compliance with the data on the nameplate and the general conditions listed in the Operating Instructions and supplementary documentation. ‣ Refer to the nameplate to check whether the ordered instrument can be operated for the intended application in areas requiring specific approvals (e. g. explosion protection, pressure equipment safety). ‣ Use the measuring device only for media to which the process-wetted materials are sufficiently resistant. ‣ Keep within the specified pressure and temperature range. ‣ Keep within the specified ambient temperature range. ‣ Protect the measuring device permanently against corrosion from environmental influences. Incorrect use Non-designated use can compromise safety. The manufacturer is not liable for damage caused by improper or non-designated use. Residual risks LCAUTION Risk of hot or cold burns! The use of media and electronics with high or low temperatures can produce hot or cold surfaces on the device. ‣ Mount suitable touch protection. ‣ Use suitable protective equipment. Endress+Hauser 9 Safety instructions Proline Prosonic Flow I 400 Modbus RS485 2.3 Workplace safety When working on and with the device: ‣ Wear the required personal protective equipment as per national regulations. 2.4 Operational safety Damage to the device! ‣ Operate the device in proper technical condition and fail-safe condition only. ‣ The operator is responsible for the interference-free operation of the device. Modifications to the device Unauthorized modifications to the device are not permitted and can lead to unforeseeable dangers! ‣ If modifications are nevertheless required, consult with the manufacturer. Repair To ensure continued operational safety and reliability: ‣ Carry out repairs on the device only if they are expressly permitted. ‣ Observe federal/national regulations pertaining to the repair of an electrical device. ‣ Use only original spare parts and accessories. 2.5 Product safety This measuring device is designed in accordance with good engineering practice to meet state-of-the-art safety requirements, has been tested, and left the factory in a condition in which it is safe to operate. It meets general safety standards and legal requirements. It also complies with the EU directives listed in the device-specific EU Declaration of Conformity. The manufacturer confirms this by affixing the CE mark to the device.. 2.6 IT security Our warranty is valid only if the product is installed and used as described in the Operating Instructions. The product is equipped with security mechanisms to protect it against any inadvertent changes to the settings. IT security measures, which provide additional protection for the product and associated data transfer, must be implemented by the operators themselves in line with their security standards. 2.7 Device-specific IT security The device offers a range of specific functions to support protective measures on the operator's side. These functions can be configured by the user and guarantee greater inoperation safety if used correctly. The following list provides an overview of the most important functions: 10 Function/interface Factory setting Recommendation Write protection via hardware write protection switch → 11 Not enabled On an individual basis following risk assessment Access code (also applies to web server login or FieldCare connection) → 11 Not enabled (0000) Assign a customized access code during commissioning Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Safety instructions Function/interface Factory setting Recommendation WLAN (order option in display module) Enabled On an individual basis following risk assessment WLAN security mode Enabled (WPA2PSK) Do not change WLAN passphrase (Password) → 11 Serial number Assign an individual WLAN passphrase during commissioning WLAN mode Access point On an individual basis following risk assessment Web server → 12 Enabled On an individual basis following risk assessment CDI-RJ45 service interface→ 12 – On an individual basis following risk assessment 2.7.1 Protecting access via hardware write protection Write access to the parameters of the device via the local display or operating tool (e.g. FieldCare, DeviceCare) can be disabled via a write protection switch (DIP switch on the main electronics module). When hardware write protection is enabled, only read access to the parameters is possible. 2.7.2 Protecting access via a password Different passwords are available to protect write access to the device parameters or access to the device via the WLAN interface. • User-specific access code Protect write access to the device parameters via the local display, web browser or operating tool (e.g. FieldCare, DeviceCare). Access authorization is clearly regulated through the use of a user-specific access code. • WLAN passphrase The network key protects a connection between an operating unit (e.g. notebook or tablet) and the device via the WLAN interface which can be ordered as an option. User-specific access code Write access to the device parameters via the local display or operating tool (e.g. FieldCare, DeviceCare) can be protected by the modifiable, user-specific access code (→ 114). When the device is delivered, the device does not have an access code and is equivalent to 0000 (open). WLAN passphrase: Operation as WLAN access point A connection between an operating unit (e.g. notebook or tablet) and the device via the WLAN interface (→ 63), which can be ordered as an optional extra, is protected by the network key. The WLAN authentication of the network key complies with the IEEE 802.11 standard. When the device is delivered, the network key is pre-defined depending on the device. It can be changed via the WLAN settings submenu in the WLAN passphrase parameter (→ 110). Endress+Hauser 11 Safety instructions Proline Prosonic Flow I 400 Modbus RS485 General notes on the use of passwords • The access code and network key supplied with the device should be changed during commissioning for safety reasons. • Follow the general rules for generating a secure password when defining and managing the access code and network key. • The user is responsible for the management and careful handling of the access code and network key. • For information on configuring the access code or on what to do if you lose the password, for example, see "Write protection via access code" → 114. 2.7.3 Access via web server The integrated web server can be used to operate and configure the device via a web browser → 56. The connection is established via the service interface (CDI-RJ45) or the WLAN interface. The web server is enabled when the device is delivered. The web server can be disabled via the Web server functionality parameter if necessary (e.g., after commissioning). The device and status information can be hidden on the login page. This prevents unauthorized access to the information. Detailed information on the device parameters: "Description of device parameters" document → 169. 2.7.4 Access via service interface (CDI-RJ45) The device can be connected to a network via the service interface (CDI-RJ45). Devicespecific functions guarantee the secure operation of the device in a network. The use of relevant industrial standards and guidelines that have been defined by national and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended. This includes organizational security measures such as the assignment of access authorization as well as technical measures such as network segmentation. 12 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 3 Product description Product description The measuring system consists of a transmitter and one or two sensor sets. The transmitter and sensor sets are mounted in physically separate locations. They are interconnected by sensor cables. The sensors function as sound generators and sound receivers. The sensors in a sensor pair are always arranged opposite one another and send/receive the ultrasonic signals directly (1-traverse positioning) → 22. The transmitter serves to control the sensor sets, to prepare, process and evaluate the measuring signals, and to convert the signals to the desired output variable. Endress+Hauser 13 Product description Proline Prosonic Flow I 400 Modbus RS485 3.1 Product design 1 2 3 4 5 6 7 8 A0045031 1 1 2 3 4 5 6 7 8 14 Important components Display module Intelligent sensor electronics module HistoROM DAT (plug-in memory) Main electronics module Terminals (screw terminals, some available as plug-in terminals) or fieldbus connectors Transmitter housing Cable glands Sensor (2 versions) Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Incoming acceptance and product identification 4 Incoming acceptance and product identification 4.1 Incoming acceptance Are the order codes on the delivery note (1) and the product sticker (2) identical? 1 2 1 2 Are the goods undamaged? Does the data on the nameplate match the order specifications on the delivery note? Order code: Ser. no.: Ext. ord. cd.: i i Date: Is the envelope present with accompanying documents? • If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center. • The Technical Documentation is available via the Internet or via the Endress+Hauser Operations app: Product identification→ 16. 4.2 Product identification The device can be identified in the following ways: • Nameplate • Order code with details of the device features on the delivery note • Enter the serial numbers from the nameplates in the Device Viewer (www.endress.com/deviceviewer): all the information about the device is displayed. • Enter the serial numbers from the nameplates into the Endress+Hauser Operations app or scan the DataMatrix code on the nameplate with the Endress+Hauser Operations app: all the information about the device is displayed. Endress+Hauser 15 Incoming acceptance and product identification Proline Prosonic Flow I 400 Modbus RS485 For an overview of the scope of the associated Technical Documentation, refer to the following: • The "Additional standard device documentation" and "Supplementary device-dependent documentation" sections • The Device Viewer: Enter the serial number from the nameplate (www.endress.com/deviceviewer) • The Endress+Hauser Operations app: Enter the serial number from the nameplate or scan the DataMatrix code on the nameplate. 4.2.1 Transmitter nameplate 34 5 67 1 2 Order code: Ser. no.: Ext. ord. cd.: 8 9 i Patents i 10 Date: 13 12 11 A0017346 2 1 2 3 4 5 6 7 8 9 10 11 12 13 Example of a transmitter nameplate Manufacturer address/certificate holder Name of the transmitter Order code Serial number Extended order code Permitted ambient temperature (Ta) Firmware version (FW) and device revision (Dev.Rev.) from the factory Degree of protection Permitted temperature range for cable 2-D matrix code Date of manufacture: year-month CE mark, RCM mark Electrical connection data, e.g. available inputs and outputs, supply voltage 4.2.2 Sensor nameplate 34 5 6 7 2 1 Order code: Ser. no.: Type.: Tm: i Date: 8 9 10 A0043306 3 1 2 3 4 5 6 7 8 9 16 Example of sensor nameplate, "front" Name of sensor Manufacturer address/certificate holder Order code Serial number Model Medium temperature range Date of manufacture: year-month Document number of safety-related supplementary documentation Additional information Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Incoming acceptance and product identification 1 A0043305 4 1 Example of sensor nameplate, "back" CE mark, RCM mark, approval information on explosion protection and degree of protection Order code The measuring device is reordered using the order code. Extended order code • The device type (product root) and basic specifications (mandatory features) are always listed. • Of the optional specifications (optional features), only the safety and approvalrelated specifications are listed (e.g. LA). If other optional specifications are also ordered, these are indicated collectively using the # placeholder symbol (e.g. #LA#). • If the ordered optional specifications do not include any safety and approval-related specifications, they are indicated by the + placeholder symbol (e.g. XXXXXX-ABCDE +). 4.2.3 Symbol Symbols on the device Meaning WARNING! This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or fatal injury. Please consult the documentation for the measuring device to discover the type of potential danger and measures to avoid it. Reference to documentation Refers to the corresponding device documentation. Protective ground connection A terminal that must be connected to the ground prior to establishing any other connections. Endress+Hauser 17 Storage and transport Proline Prosonic Flow I 400 Modbus RS485 5 Storage and transport 5.1 Storage conditions Observe the following notes for storage: ‣ Store in the original packaging to ensure protection from shock. ‣ Protect from direct sunlight. Avoid unacceptably high surface temperatures. ‣ Store in a dry and dust-free place. ‣ Do not store outdoors. Storage temperature → 160 5.2 Transporting the product Transport the measuring device to the measuring point in the original packaging. 5.2.1 Transporting with a fork lift If transporting in wood crates, the floor structure enables the crates to be lifted lengthwise or at both sides using a forklift. 5.3 Packaging disposal All packaging materials are environmentally friendly and 100% recyclable: • Outer packaging of device Stretch wrap made of polymer in accordance with EU Directive 2002/95/EC (RoHS) • Packaging • Wood crate treated in accordance with ISPM 15 standard, confirmed by IPPC logo • Cardboard box in accordance with European packaging guideline 94/62/EC, recyclability confirmed by Resy symbol • Transport material and fastening fixtures • Disposable plastic pallet • Plastic straps • Plastic adhesive strips • Filler material Paper pads 18 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 6 Mounting procedure 6.1 Mounting requirements 6.1.1 Mounting position Mounting procedure Mounting location A0045279 To prevent measuring errors arising from accumulation of gas bubbles in the measuring pipe, avoid the following mounting locations in the piping: • Highest point of a pipeline. • Directly upstream of a free pipe outlet in a down pipe. Endress+Hauser 19 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 Orientation 1 2 3 4 2 B C A 1 C B A0045281 5 1 2 3 4 A B C Orientation views Channel 1 upstream Channel 1 downstream Channel 2 upstream Channel 2 downstream Recommended orientation with upward flow direction Non-recommended installation range with horizontal orientation (60°) Recommended installation range max. 120° Vertical Recommended orientation with upward flow direction (view A) With this orientation, entrained solids sink and gases rise away from the sensor area when the medium is not flowing. In addition, the pipe can be completely drained and protected against the buildup of deposits. Horizontal In the recommended installation range with a horizontal orientation (View B), gas and air accumulations at the top of the pipe and inteference from deposit buildup at the bottom of the pipe can influence the measurement to a lesser degree. Inlet and outlet runs If possible, install the sensors upstream of assemblies such as valves, T-pieces, elbows, and pumps. If this is not possible, the specified measurement accuracy of the measuring device is achieved by observing the specified minimum inlet and outlet runs with optimum sensor configuration. If there are several flow obstructions, the longest specified inlet run must be taken into account. 20 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Mounting procedure 1 2 3 × DN 3 × DN A: 15 × DN B: 10 × DN A: 15 × DN B: 10 × DN 3 4 3 × DN 3 × DN b a A: 15 × DN B: 10 × DN A: 15 × DN B: 10 × DN 5 6 3 × DN A: 20 × DN B: 20 × DN 3 × DN A: 20 × DN B: 15 × DN A0045289 6 1 2 3 4a 4b 5 6 Minimum inlet and outlet runs with different flow obstructions (A: single-path measurement, B: two-path measurement) Pipe bend Two pipe bends (on one plane) Two pipe bends (on two planes) Reduction Extension Control valve (2/3 open) Pump Measuring mode Single-path measurement → 6, 21 Endress+Hauser 21 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 Two-path measurement 120° 120° A0044945 7 Two-path measurement: example of horizontal arrangement of the sensor sets at a measuring point Installation dimensions For the dimensions and installation lengths of the device, see the "Technical Information" document, "Mechanical construction" section 6.1.2 Sensor set selection and arrangement If mounting horizontally, always mount the sensor set so that it is offset at an angle of ±30° to the top of the measuring pipe to avoid incorrect measurements caused by gas pockets or bubbles at the top of the pipe. The sensors can be arranged in different ways: • Mounting arrangement for measurement with one sensor set (one measuring path): The sensors are located on opposite sides of the measuring pipe (offset by 180°) • Mounting for measurement with two sensor sets 1) (two measuring paths): One sensor of each sensor set is located at the opposite side of the measuring pipe Single-path measurement (1 sensor set) Vertical mounting A0044939 1) 22 Do not swap the sensors of the two sensor sets, as this can affect the measurement performance. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Mounting procedure Single-path measurement (1 sensor set) Horizontal mounting 120° 120° A0044304 Two-path measurement (2 sensor sets) Vertical mounting A0044940 Horizontal mounting 120° 120° A0044942 6.1.3 Environmental and process requirements Ambient temperature range Endress+Hauser Transmitter –40 to +60 °C (–40 to +140 °F) Readability of the local display –20 to +60 °C (–4 to +140 °F) The readability of the display may be impaired at temperatures outside the temperature range. 23 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 Sensor Standard: –40 to +80 °C (–40 to +176 °F) Sensor cable (connection between transmitter and sensor) Standard: TPE halogen-free: –40 to +80 °C (–40 to +176 °F) In principle, it is permitted to insulate the sensors mounted on the pipe. In the case of insulated sensors, make sure that the process temperature does not exceed or drop below the specified cable temperature. ‣ If operating outdoors: Avoid direct sunlight, particularly in warm climatic regions. Medium pressure range Maximum nominal pressure PN 16 (16 bar (232 psi)) 6.1.4 Special mounting instructions Display guard ‣ To ensure that the display guard can be easily opened, maintain the following minimum head clearance: 350 mm (13.8 in) 203 (8.0) 243 (9.6) 213 (8.4) 39 (1.5) Weather protection cover A0029552 8 Weather protection cover; engineering unit mm (in) 6.2 Mounting the measuring device 6.2.1 Required tools For transmitter • Torque wrench • For wall mounting: Open-ended wrench for hexagonal screw max. M5 • For pipe mounting: • Open-ended wrench AF 8 • Phillips head screwdriver PH 2 For sensor For mounting on the measuring tube: Use a suitable mounting tool. 24 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 6.2.2 Mounting procedure Preparing the measuring device 1. Remove all remaining transport packaging. 2. Remove stick-on label on the electronics compartment cover. 6.2.3 Mounting the sensor Sensor configuration and settings DN 200 to 4000 (8 to 160") 1) Single-path version [mm (in)] Two-path version [mm (in)] Sensor distance 1) Sensor distance 1) Path length → 9, 25 Path length → 9, 25 Arc length → 9, 25 Depends on the conditions at the measuring point (e.g. measuring pipe). The mounting position of the sensor can be determined via FieldCare or Applicator. See also Result Sensor Type / Sensor Distance parameter in Measuring point submenu Determining the mounting positions of the sensor Description of installation 1 d a c a 2 b d b c A0044950 9 1 2 a b c d Terminology Description of installation Single-path version Two-path version Sensor distance Arc length Path length External diameter of measuring pipe Detailed information: Endress+Hauser 25 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 Sensor holder for single-path version Procedure: 1. Determine mounting area (e) on measuring pipe section (space required at measuring point approx. 1x diameter of measuring pipe). 2. Mark the center line on the measuring pipe at the mounting location and mark the first the drill hole (drill hole diameter: 65 mm (2.56 in)). The center line marking should extend beyond the hole to be drilled. e A0044951 3. Cut the first drill hole using a plasma cutter, for example. Measure the wall thickness of the measuring pipe, if not already known. 4. Determine the sensor distance → 25. A0044952 5. Mark the sensor distance (a) starting from the center line of the first drill hole. 6. Project and draw the center line onto the rear of the measuring pipe. a A0044953 7. 26 Mark the drill hole on the rear center line. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8. Mounting procedure Cut out the second drill hole and prepare holes for welding in the sensor holders (deburr, clean). A0044954 9. Insert sensor holders into both drill holes. To adjust the welding depth, both sensor holders can be secured with the special tool for regulating the insertion depth and then aligned using the path rod. The senor holder must be flush with the inside of the measuring pipe. 10. Spot-weld both sensor holders. To align the path rod, screw both guide bushes into the sensor holders. A0044955 11. Weld in both sensor holders. 12. Check the distances between the drill holes again and determine the path length → 25. 13. Manually screw the sensors into the sensor holders. If using a tool, tighten with max. 30 Nm. 14. Insert the sensor cable plugs into the openings provided and manually tighten the plugs as far as they will go. A0044956 Sensor holder for two-path version Procedure: 1. Endress+Hauser Determine mounting area (e) on measuring pipe section (space required at measuring point approx. 1x diameter of measuring pipe). 27 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 2. Mark the center line on the measuring pipe at the mounting location. e A0044951 3. Draw the length of the arc (b) at the mounting position of the sensor holder from the center line out to one side. Base the arc length on approx. 1/12 of the circumference of the measuring pipe. Mark the first drill hole (drill hole diameter: 81 to 82 mm (3.19 to 3.23 in)). Extend the center line beyond the hole to be drilled. 4. Cut the first drill hole using a plasma cutter, for example. Measure the wall thickness of the measuring pipe, if not already known. b A0044957 5. Determine the sensor distance and arc length → 25. 6. Use the arc length that was determined to correct the center line. A0044958 7. 28 Project and draw the corrected center line onto the opposite side of the measuring pipe (half of measuring pipe circumference). Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8. Mounting procedure Mark the sensor distance on the center line and project it onto the center line on the rear of the pipe. a A0044959 9. Draw the length of the arc from the center line out to both sides and mark the drill holes. 10. Create drill holes and prepare them for welding in the sensor holders (deburr, clean). Drill holes for the sensor holders are paired together (CH 1 - CH 1 and CH 2 - CH 2). CH 1 CH 1 CH 2 CH 2 A0044960 11. Insert the sensor holders into the first two drill holes and align them using the path rod (alignment tool). Spot-weld with the welding device and then weld both sensor holders together. To align the path rod, screw both guide bushes into the sensor holders. A0044961 12. Weld in both sensor holders. 13. Check the path length, sensor distances and arc lengths again. Deviations can be entered as calibration factors later on when commissioning the measuring point. Endress+Hauser 29 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 14. Insert second pair of sensor holders into the two remaining drill holes as per step 11, and then weld in place. A0044962 A0044963 15. Manually screw the sensors into the sensor holders. If using a tool, tighten with max. 30 Nm. 16. Insert the sensor cable plugs into the openings provided and manually tighten the plugs as far as they will go. A0044964 6.2.4 Mounting the transmitter LCAUTION Ambient temperature too high! Danger of electronics overheating and housing deformation. ‣ Do not exceed the permitted maximum ambient temperature. → 23 ‣ If operating outdoors: Avoid direct sunlight and exposure to weathering, particularly in warm climatic regions. LCAUTION Excessive force can damage the housing! ‣ Avoid excessive mechanical stress. The transmitter of the remote version can be mounted in the following ways: • Wall mounting • Pipe mounting 30 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Mounting procedure Wall mounting 17 (0.67) = = 14 (0.55) 210.5 (8.29) 5.8 (0.23) 5.8 (0.23) 149 (5.85) A0020523 10 Unit mm (in) 1. Drill the holes. 2. Insert wall plugs into the drilled holes. 3. Lightly screw in the securing screws. 4. Fit the transmitter housing over the securing screws and hook into place. 5. Tighten the securing screws. Post mounting NOTICE Excessive tightening torque applied to the fixing screws! Risk of damaging the plastic transmitter. ‣ Tighten the fixing screws as per the tightening torque: 2.5 Nm (1.8 lbf ft) ø 20…70 (ø 0.79…2.75) 4x 3x TX 25 SW 10 ~1 0 ~ 2( ) 4.0 A0029051 11 Endress+Hauser Unit mm (in) 31 Mounting procedure Proline Prosonic Flow I 400 Modbus RS485 6.2.5 Turning the display module The display module can be turned to optimize display readability and operability. 1. 4 x 4. 3. TX 20 P R US E H M O TO V E P R US E H M O TO V E 2. A0046804 1. Loosen the fixing screws of the housing cover. 2. Open the housing cover. 3. Unlock the display module. 4. Pull out the display module and turn it to the desired position in increments of 90°. Mounting the transmitter housing LWARNING Excessive tightening torque applied to the fixing screws! Damage to the transmitter. ‣ Tighten the fixing screws with the specified torques. 1. Insert the display module and lock it when doing so. 2. Close the housing cover. 3. Tighten the fixing screws of the housing cover: tightening torque for aluminum housing 2.5 Nm (1.8 lbf ft) – plastic housing 1 Nm (0.7 lbf ft). 6.3 Post-mounting check Is the measuring device undamaged (visual inspection)? Does the measuring device correspond to the measuring point specifications? For example: • Process temperature → 161 • Inlet run conditions • Ambient temperature • Measuring range Has the correct orientation for the sensor been selected → 20? 32 • According to sensor type • According to medium temperature • According to medium properties (outgassing, with entrained solids) Are the sensors correctly connected to the transmitter (upstream/downstream) → 5, 20? Are the sensors correctly mounted (distance, path length, arc length) → 22? Is the tag name and labeling correct (visual inspection)? Is the device sufficiently protected from precipitation and direct sunlight? Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Endress+Hauser Mounting procedure Are the securing screw and securing clamp tightened securely? Is the sensor holder properly grounded (in the event of different potential between the sensor holder and transmitter)? 33 Electrical connection Proline Prosonic Flow I 400 Modbus RS485 7 Electrical connection LWARNING Live parts! Incorrect work performed on the electrical connections can result in an electric shock. ‣ Set up a disconnecting device (switch or power-circuit breaker) to easily disconnect the device from the supply voltage. ‣ In addition to the device fuse, include an overcurrent protection unit with max. 16 A in the plant installation. 7.1 Electrical safety In accordance with applicable national regulations. 7.2 Connecting requirements 7.2.1 Required tools • Torque wrench • For cable entries: Use corresponding tools • Wire stripper • When using stranded cables: Crimper for wire end ferrule 7.2.2 Requirements for connecting cable The connecting cables provided by the customer must fulfill the following requirements. Permitted temperature range • The installation guidelines that apply in the country of installation must be observed. • The cables must be suitable for the minimum and maximum temperatures to be expected. Power supply cable (incl. conductor for the inner ground terminal) Standard installation cable is sufficient. Signal cable Modbus RS485 The EIA/TIA-485 standard specifies two types of cable (A and B) for the bus line which can be used for every transmission rate. Cable type A is recommended. 34 Cable type A Characteristic impedance 135 to 165 Ω at a measuring frequency of 3 to 20 MHz Cable capacitance < 30 pF/m Wire cross-section > 0.34 mm2 (22 AWG) Cable type Twisted pairs Loop resistance ≤110 Ω/km Signal damping Max. 9 dB over the entire length of the cable cross-section Shield Copper braided shielding or braided shielding with foil shield. When grounding the cable shield, observe the grounding concept of the plant. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Electrical connection Connecting cable between the transmitter and sensor Sensor cable for sensor - transmitter 3 2 1 4 A0045277 Standard cable TPE halogen-free: -40 to +80 °C (-40 to +176 °F) Cable length (max.) 30 m (90 ft) Cable lengths (available for order) 5 m (15 ft), 10 m (30 ft), 15 m (45 ft), 30 m (90 ft) Operating temperature Depends on the device version and how the cable is installed: Standard version: • Cable - fixed installation 1): minimum –40 °C (–40 °F) • Cable - movable installation: minimum –25 °C (–13 °F) 1) Compare details under the row "Standard cable" Cable diameter • Cable glands supplied: • For standard cable: M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in) • For reinforced cable: M20 × 1.5 with cable 9.5 to 16 mm (0.37 to 0.63 in) • (Plug-in) spring terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG) 7.2.3 Terminal assignment Transmitter The sensor can be ordered with terminals. Connection methods available Outputs Power supply Terminals Terminals Possible options for order code "Electrical connection" • Option A: coupling M20x1 • Option B: thread M20x1 • Option C: thread G ½" • Option D: thread NPT ½" Supply voltage Order code "Power supply" Option L (wide range power unit) Endress+Hauser Terminal numbers 1 (L+/L), 2 (L-/N) terminal voltage Frequency range DC 24 V ±25% – AC 24 V ±25% 50/60 Hz, ±4 Hz AC 100 to 240 V –15 to +10% 50/60 Hz, ±4 Hz 35 Electrical connection Proline Prosonic Flow I 400 Modbus RS485 Signal transmission Modbus RS485 and additional outputs Order code for "Output" and "Input" Terminal numbers 26 (+) Option M 27 (-) Modbus B Option O 7.2.4 24 (+) 25 (-) 22 (+) 23 (-) 20 (+) 21 (-) - - - Pulse/frequency/ switch output (passive) Pulse/frequency/ switch output (passive) Modbus A Current output 4 to 20 mA (active) B A Shielding and grounding Shielding and grounding concept 1. Maintain electromagnetic compatibility (EMC). 2. Take explosion protection into consideration. 3. Pay attention to the protection of persons. 4. Comply with national installation regulations and guidelines. 5. Observe cable specifications . 6. Keep the stripped and twisted lengths of cable shield to the ground terminal as short as possible. 7. Shield cables fully. Grounding of the cable shield NOTICE In systems without potential matching, the multiple grounding of the cable shield causes mains frequency equalizing currents! Damage to the bus cable shield. ‣ Only ground the bus cable shield to either the local ground or the protective ground at one end. ‣ Insulate the shield that is not connected. To comply with EMC requirements: 1. Ensure the cable shield is grounded to the potential matching line at multiple points. 2. Connect every local ground terminal to the potential matching line. 7.2.5 Preparing the measuring device Carry out the steps in the following order: 1. Mount the sensor and transmitter. 2. Sensor connection housing: Connect sensor cable. 3. Transmitter: Connect sensor cable. 4. Transmitter: Connect cable for supply voltage. NOTICE Insufficient sealing of the housing! Operational reliability of the measuring device could be compromised. ‣ Use suitable cable glands corresponding to the degree of protection. 36 1. Remove dummy plug if present. 2. If the measuring device is supplied without cable glands: Provide suitable cable gland for corresponding connecting cable. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 3. Electrical connection If the measuring device is supplied with cable glands: Observe requirements for connecting cables → 34. 7.3 Connecting the measuring device LWARNING Risk of electric shock! Components carry dangerous voltages! ‣ Have electrical connection work carried out by correspondingly trained specialists only. ‣ Observe applicable federal/national installation codes and regulations. ‣ Comply with local workplace safety regulations. ‣ Observe grounding concept of the plant. ‣ Never mount or wire the measuring device while it is connected to the supply voltage. ‣ Before the supply voltage is applied, connect the protective ground to the measuring device. 7.3.1 Connecting the sensor with transmitter LWARNING Risk of damaging electronic components! ‣ Connect the sensor and transmitter to the same potential equalization. ‣ Only connect the sensor to a transmitter with the same serial number. The following sequence of steps is recommended when connecting: 1. Mount the sensor and transmitter. 2. Connect the sensor cable. 3. Connect the transmitter. Connecting the sensor cable to the transmitter 1. 4 x T 20 2. 5. UP 6. Down 8. UP 9. Down CH1 7. CH2 3. 4. A0046768 12 Endress+Hauser Transmitter: main electronics module with terminals 1. Loosen the 4 fixing screws on the housing cover. 2. Open the housing cover. 3. Route the two sensor cables of channel 1 through the slackened top union nut of the cable entry. To ensure tight sealing, mount a sealing insert on the sensor cables (push the cables through the slotted sealing insert). 37 Electrical connection Proline Prosonic Flow I 400 Modbus RS485 4. Mount the screw part in the center cable entry at the top and then guide both sensor cables through the entry. Then fit the coupling nut with the sealing insert on the screw part and tighten. Ensure that the sensor cables are positioned in the cut-outs provided in the screw part. 5. Connect sensor cable to channel 1 upstream. 6. Connect sensor cable to channel 1 downstream. 7. For a two-path measurement: proceed as per steps 3+4 8. Connect sensor cable to channel 2 upstream. 9. Connect sensor cable to channel 2 downstream. 10. Tighten the cable gland(s). This concludes the process for connecting the sensor cable(s). 11. LWARNING Housing degree of protection may be voided due to insufficient sealing of the housing. ‣ Screw in the screw without using any lubricant. Reverse the removal procedure to reassemble the transmitter. 38 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 7.3.2 Electrical connection Connecting the transmitter LWARNING Housing degree of protection may be voided due to insufficient sealing of the housing. ‣ Screw in the screw without using any lubricant. The threads on the cover are coated with a dry lubricant. Tightening torques for plastic housing Housing cover fixing screw 1 Nm (0.7 lbf ft) Cable entry 5 Nm (3.7 lbf ft) Ground terminal 2.5 Nm (1.8 lbf ft) 1. Loosen the 4 fixing screws on the housing cover. 2. Open the housing cover. 3. Push the cable through the cable entry. To ensure tight sealing, do not remove the sealing ring from the cable entry. 4. Strip the cable and cable ends. In the case of stranded cables, also fit ferrules. 5. Connect the cable according to the terminal assignment → 35. For supply voltage: open the shock protection cover. 6. Firmly tighten the cable glands. Reassembling the transmitter 1. Close the shock protection cover. 2. Close the housing cover. 3. LWARNING Housing degree of protection may be voided due to insufficient sealing of the housing. ‣ Screw in the screw without using any lubricant. Tighten the 4 fixing screws on the housing cover. 7.3.3 Potential equalization Requirements For potential equalization: • Pay attention to in-house grounding concepts • Take account of operating conditions like the pipe material and grounding • Connect the sensor and transmitter to the same electric potential 2) • Use a ground cable with a minimum cross-section of 6 mm2 (10 AWG) and a cable lug for potential equalization connections 2) Endress+Hauser 39 Electrical connection Proline Prosonic Flow I 400 Modbus RS485 7.4 Special connection instructions 7.4.1 Connection examples Modbus RS485 1 3 2 A A 4 B B A 4 B A0028765 13 1 2 3 4 Connection example for Modbus RS485, non-hazardous area and Zone 2/Div. 2 Control system (e.g. PLC) Ground cable shield at one end. The cable shield must be grounded at both ends to comply with EMC requirements; observe cable specifications Distribution box Transmitter 7.5 Hardware settings 7.5.1 Activating the terminating resistor Modbus RS485 To avoid incorrect communication transmission caused by impedance mismatch, terminate the Modbus RS485 cable correctly at the start and end of the bus segment. 5V 390 Ω 220 Ω DIP 2 26 390 Ω Bus polar. Bus polar. Not used DIP 3 DIP 1 Bus term. 0V 1 2 3 4 ON OFF 27 A0023063 14 Terminating resistor can be enabled via DIP switch on the electronics module 7.6 Ensuring the degree of protection 7.6.1 Degree of protection IP66/67, Type 4X enclosure The measuring device fulfills all the requirements for the degree of protection IP66/67, Type 4X enclosure. 40 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Electrical connection To guarantee the degree of protection IP66/67, Type 4X enclosure, carry out the following steps after electrical connection: 1. Check that the housing seals are clean and fitted correctly. Dry, clean or replace the seals if necessary. 2. Tighten all housing screws and screw covers. 3. Firmly tighten the cable glands. 4. To ensure that moisture does not enter the cable entry, route the cable so that it loops down before the cable entry ("water trap"). A0029278 5. The cable glands supplied do not ensure housing protection when not in use. They must therefore be replaced by dummy plus corresponding to the housing protection. NOTICE Standard dummy plugs used for transportation do not have the appropriate degree of protection and can result in damage to the device! ‣ Use suitable dummy plugs corresponding to the degree of protection. 7.7 Endress+Hauser Post-connection check Are cables or the device undamaged (visual inspection)? Do the cables used comply with the requirements → 34? Are the mounted cables relieved of tension? Are all cable glands installed, securely tightened and leak-tight? Cable run with "water trap" → 40? Does the supply voltage match the specifications on the transmitter nameplate → 156? Is the terminal assignment correct → 35? If supply voltage is present, do values appear on the display module? Are all housing covers installed and the screws tightened with the correct tightening torque? 41 Operation options Proline Prosonic Flow I 400 Modbus RS485 8 Operation options 8.1 Overview of operation methods ESC - + 1 E 2 3 4 5 6 A0046501 1 2 3 4 5 6 42 Local operation via display module Computer with Web browser (e.g. Internet Explorer) or with operating tool (e.g. FieldCare, DeviceCare, AMS Device Manager, SIMATIC PDM) Field Xpert SFX350 or SFX370 Field Xpert SMT70 Mobile handheld terminal Control system (e.g. PLC) Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options 8.2 Structure and function of the operating menu 8.2.1 Structure of the operating menu For an overview of the operating menu for experts: see the "Description of Device Parameters" document supplied with the device → 169 Operating menu for operators and maintenances Language Operatation ! Language Operator Parameter 1 Parameter n Submenu 1 Submenu n Setup Device tag Wizard n / Parameter n Advanced setup Enter access code Parameter 1 Task-oriented Maintenance Wizard 1 / Parameter 1 Parameter n Submenu 1 Submenu n Diagnostics Parameter 1 Parameter n Submenu 1 Submenu n Operating menu for experts Expert Access status display Parameter n Sensor Input Output Communication Function-oriented Expert System Application Diagnostics A0018237-EN 15 Endress+Hauser Schematic structure of the operating menu 43 Operation options Proline Prosonic Flow I 400 Modbus RS485 8.2.2 Operating philosophy The individual parts of the operating menu are assigned to certain user roles (e.g. operator, maintenance etc.). Each user role contains typical tasks within the device life cycle. Menu/parameter Language Taskoriented Operation Setup User role and tasks Content/meaning Role "Operator", "Maintenance" Tasks during operation: • Configuration of the operational display • Reading measured values • Defining the operating language • Defining the Web server operating language • Resetting and controlling totalizers "Maintenance" role Commissioning: Configuration of the measurement Wizards for fast commissioning: • Configuring the measuring point • Configuring the system units • Configuring the input • Configuring the outputs • Configuration of the operational display • Definition of output conditioning • Configuring the low flow cut off • Configuration of the operational display (e.g. display format, display contrast) • Resetting and controlling totalizers Advanced setup • For more customized configuration of the measurement (adaptation to special measuring conditions) • Configuration of totalizers • Configuration of WLAN settings • Administration (define access code, reset measuring device) Diagnostics Expert 44 Functionoriented "Maintenance" role Troubleshooting: • Diagnostics and elimination of process and device errors • Measured value simulation Contains all parameters for error detection and analyzing process and device errors: • Diagnostic list Contains up to 5 currently pending diagnostic messages. • Event logbook Contains event messages that have occurred. • Device information Contains information for identifying the device • Measured values Contains all current measured values. • Data logging submenu with the "Extended HistoROM" order option Storage and visualization of measured values • Heartbeat Technology Verification of device functionality on request and documentation of verification results • Simulation Used to simulate measured values or output values. Tasks that require detailed knowledge of the function of the device: • Commissioning measurements under difficult conditions • Optimal adaptation of the measurement to difficult conditions • Detailed configuration of the communication interface • Error diagnostics in difficult cases Contains all of the device parameters and allows direct access to these by means of an access code. The structure of this menu is based on the function blocks of the device: • System Contains all higher-level device parameters that do not affect measurement or measured value communication • Sensor Configuration of the measurement. • Input Configuration of the status input • Output Configuration of the analog current outputs as well as the pulse/frequency and switch output • Communication Configuration of the digital communication interface and the Web server • Application Configuration of the functions that go beyond the actual measurement (e.g. totalizer) • Diagnostics Error detection and analysis of process and device errors and for device simulation and Heartbeat Technology. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options 8.3 Access to operating menu via local display 8.3.1 Operational display 1 2 F XXXXXXXXX 4 3 1120.50 l/h 5 A0029346 1 2 3 4 5 Operational display Device tag Status area Display range for measured values (up to 4 lines) Operating elements → 50 Status area The following symbols appear in the status area of the operational display at the top right: • Status signals→ 129 • F: Failure • C: Function check • S: Out of specification • M: Maintenance required • Diagnostic behavior→ 130 • : Alarm • : Warning • : Locking (the device is locked via the hardware ) • : Communication (communication via remote operation is active) Display area In the display area, each measured value is prefaced by certain symbol types for further description: Measured variable Measurement channel number Diagnostic behavior ↓ ↓ ↓ Example Appears only if a diagnostics event is present for this measured variable. Measured variables Symbol Meaning Mass flow Sound velocity Endress+Hauser 45 Operation options Proline Prosonic Flow I 400 Modbus RS485 Flow velocity Signal to noise ratio Signal strength The number and display format of the measured variables can be configured via the Format display parameter (→ 100). Totalizer Symbol Meaning Totalizer The measurement channel number indicates which of the three totalizers is displayed. Output Symbol Meaning Output The measurement channel number indicates which of the outputs is displayed. Input Symbol Meaning Status input Measurement channel numbers Symbol Meaning Measurement channel 1 to 4 The measurement channel number is displayed only if more than one channel is present for the same measured variable type (e.g. totalizer 1 to 3). Diagnostic behavior Symbol Meaning Alarm • Measurement is interrupted. • Signal outputs and totalizers assume the defined alarm condition. • A diagnostic message is generated. • The background lighting changes to red. Warning • Measurement is resumed. • The signal outputs and totalizers are not affected. • A diagnostic message is generated. The diagnostic behavior pertains to a diagnostic event that is relevant to the displayed measured variable. 46 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8.3.2 2 Operation options Navigation view In the submenu In the wizard 1 1 0091-1 /../Operation Access stat.disp 3 /../Curr. output 1 S Assign curr. Volume flow 2 Operator Locking status Display 4 4 5 5 A0013993-EN 1 2 3 4 5 3 A0016327-EN Navigation view Navigation path to current position Status area Display area for navigation Operating elements → 50 Navigation path The navigation path to the current position is displayed at the top left in the navigation view and consists of the following elements: • The display symbol for the menu/submenu ( ) or the wizard ( ). • An omission symbol (/ ../) for operating menu levels in between. • Name of the current submenu, wizard or parameter Display symbol Omission symbol Parameter ↓ ↓ ↓ / ../ Indication Example For more information about the icons in the menu, refer to the "Display area" section → 47 Status area The following appears in the status area of the navigation view in the top right corner: • In the submenu • The direct access code to the parameter (e.g., 0022-1) • If a diagnostic event is present, the diagnostic behavior and status signal • In the wizard If a diagnostic event is present, the diagnostic behavior and status signal • For information on the diagnostic behavior and status signal → 129 • For information on the function and entry of the direct access code → 52 Display area Menus Symbol Meaning Operation Is displayed: • In the menu next to the "Operation" selection • At the left in the navigation path in the Operation menu Endress+Hauser 47 Operation options Proline Prosonic Flow I 400 Modbus RS485 Setup Is displayed: • In the menu next to the "Setup" selection • At the left in the navigation path in the Setup menu Diagnosis Is displayed: • In the menu next to the "Diagnostics" selection • At the left in the navigation path in the Diagnostics menu Expert Is displayed: • In the menu next to the "Expert" selection • At the left in the navigation path in the Expert menu Submenus, wizards, parameters Symbol Meaning Submenu Wizards Parameters within a wizard No display symbol exists for parameters in submenus. Locking procedure Symbol Meaning Parameter locked When displayed in front of a parameter name, indicates that the parameter is locked. • By a user-specific access code • By the hardware write protection switch Wizards Symbol Meaning Switches to the previous parameter. Confirms the parameter value and switches to the next parameter. Opens the editing view of the parameter. 8.3.3 2 Editing view Numeric editor Text editor 1 1 2 20 0 5 1 6 2 7 3 8 4 9 DEFG PQRS HIJK TUVW Aa1 3 4 A0013941 48 ABC_ LMNO XYZ 3 4 1 2 3 4 User A0013999 Editing view Display area of the entered values Input mask Operating elements → 50 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options Input screen The following input symbols are available in the input mask of the numeric and text editor: Numeric editor Symbol Meaning 0 … 9 . – Selection of numbers from 0 to 9 Inserts a decimal separator at the cursor position. Inserts a minus sign at the cursor position. Confirms the selection. Moves the input position one position to the left. Exits the input without applying the changes. Clears all entered characters. Text editor Symbol Aa1 Meaning Toggle • Between upper-case and lower-case letters • For entering numbers • For entering special characters ABC _ … XYZ Selection of letters from A to Z. abc _ … xyz Selection of letters from a to z. "'^ _ … ~& _ Selection of special characters. Confirms the selection. Switches to the selection of the correction tools. Exits the input without applying the changes. Clears all entered characters. Text correction under Symbol Meaning Clears all entered characters. Endress+Hauser 49 Operation options Proline Prosonic Flow I 400 Modbus RS485 Moves the input position one position to the right. Moves the input position one position to the left. Deletes one character immediately to the left of the input position. 8.3.4 Operating elements Operating key Meaning Minus key In menu, submenu Moves the selection bar upwards in a picklist In wizards Goes to previous parameter In the text and numeric editor In the input screen, moves the selection bar to the left (backwards) Plus key In menu, submenu Moves the selection bar downwards in a picklist In wizards Goes to the next parameter In the text and numeric editor In the input screen, moves the selection bar to the right (forwards) Enter key In the operational display Pressing the key for 2 s opens the context menu including the option for activating the keypad lock. In menu, submenu • Pressing the key briefly: • Opens the selected menu, submenu or parameter. • Starts the wizard. • If help text is open, closes the help text of the parameter. • Pressing the key for 2 s in a parameter: If present, opens the help text for the function of the parameter. In wizards Opens the editing view of the parameter and confirms the parameter value In the text and numeric editor • Pressing the key briefly: • Opens the selected group. • Carries out the selected action. • Pressing the key for 2 s confirms the edited parameter value. Escape key combination (press keys simultaneously) In menu, submenu • Pressing the key briefly: • Exits the current menu level and takes you to the next higher level. • If help text is open, closes the help text of the parameter. • Pressing the key for 2 s returns you to the operational display ("home position"). + In wizards Exits the wizard and takes you to the next higher level In the text and numeric editor Closes the text or numeric editor without applying changes. Minus/Plus/Enter key combination (press the keys simultaneously) + 50 + In the operational display Enables or disables the keypad lock (only SD02 display module). Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8.3.5 Operation options Opening the context menu Using the context menu, the user can call up the following menus quickly and directly from the operational display: • Setup • Simulation Calling up and closing the context menu The user is in the operational display. 1. Press the and keys for longer than 3 seconds. The context menu opens. XXXXXXXXXX Setup Conf.backup Simulation Keylock on A0034608-EN 2. Press + simultaneously. The context menu is closed and the operational display appears. Calling up the menu via the context menu Endress+Hauser 1. Open the context menu. 2. Press to navigate to the desired menu. 3. Press to confirm the selection. The selected menu opens. 51 Operation options Proline Prosonic Flow I 400 Modbus RS485 8.3.6 Navigating and selecting from list Different operating elements are used to navigate through the operating menu. The navigation path is displayed on the left in the header. Icons are displayed in front of the individual menus. These icons are also shown in the header during navigation. For an explanation of the navigation view with symbols and operating elements → 47 Example: Setting the number of displayed measured values to "2 values" XXXXXXXXX 20.50 1. 0104-1 Main menu Language English Display/operat. Setup 2. Main menu Language Display/operat. Setup / ../Display/operat. 0091-1 Access stat.disp 3. Operator Locking status Display / ../Display/operat. Locking status Display 4. / ../Display 0098-1 Format display 1 value, max. Contrast display Display intervall 5. / ../Format display 1 value, max. Bargr. + 1 value 2 values Val. large+2val. 6. 0098-1 0098-1 / ../Format display 1 value, max. Bargr. + 1 value 2 values Val. large+2val. 7. XXXXXXXXX 8. 2s 10.50 mA 2800 Hz A0029562-EN 8.3.7 Calling the parameter directly A parameter number is assigned to every parameter to be able to access a parameter directly via the onsite display. Entering this access code in the Direct access parameter calls up the desired parameter directly. Navigation path Expert → Direct access 52 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options The direct access code consists of a 5-digit number (at maximum) and the channel number, which identifies the channel of a process variable: e.g. 00914-2. In the navigation view, this appears on the right-hand side in the header of the selected parameter. 00914-2 1 A0029414 1 Direct access code Note the following when entering the direct access code: • The leading zeros in the direct access code do not have to be entered. Example: Enter "914" instead of "00914" • If no channel number is entered, channel 1 is opened automatically. Example: Enter 00914 → Assign process variable parameter • If a different channel is opened: Enter the direct access code with the corresponding channel number. Example: Enter 00914-2 → Assign process variable parameter For the direct access codes of the individual parameters, see the "Description of Device Parameters" document for the device 8.3.8 Calling up help text Help text is available for some parameters and can be called up from the navigation view. The help text provides a brief explanation of the parameter function and thereby supports swift and safe commissioning. Calling up and closing the help text The user is in the navigation view and the selection bar is on a parameter. 1. Press for 2 s. The help text for the selected parameter opens. Ent. access code Enter access code to disable write protec. A0014002-EN 16 2. Endress+Hauser Example: Help text for parameter "Enter access code" Press + simultaneously. The help text is closed. 53 Operation options Proline Prosonic Flow I 400 Modbus RS485 8.3.9 Changing the parameters For a description of the editing view - consisting of the text editor and numeric editor - with symbols → 48, for a description of the operating elements → 50 Example: Changing the tag name in the "Tag description" parameter from 001-FT-101 to 001-FT-102 1496-1 /../Advanced setup Ent. access code Tag description 001-FT-101 Def. access code 1. 2. 001-FT-101 3x ABC LMNO XYZ 3. 001-FT-10 ABC 4. ABC LMNO XYZ HIJK TUVW Aa1@ DEFG HIJK DEFG HIJK DEFG PQRS HIJK TUVW Aa1@ DEFG HIJK 3456 /[] 789 () Aa1@ 3456 789 3456 /[] 789 () Aa1@ ABC 001-FT-10 1x ABC LMNO XYZ 6. 001-FT-10 ABC 2x A a ABC LMNO XYZ 001-FT-102 4x 012 =+-* 0 1 2 <>{} 8. 001-FT-10 012 2x 0 1 9. 001-FT-102 1x 012 =+-* 0 1 2 <>{} DEFG HIJK DEFG PQRS HIJK TUVW Aa1@ DEFG HIJK 3456 /[] 789 () Aa1@ 3456 789 3456 /[] 789 () Aa1@ 001-FT-10 ABC A a 1 @ 001-FT-10 012 =+-* <>{} 1 @ 7. HIJK TUVW Aa1@ 001-FT-10 1x 5. DEFG PQRS 001-FT-101 DEFG PQRS 001-FT-10 ABC 001-FT-101 001-FT-10 012 0 1 2 001-FT-102 2 012 =+-* 0 1 2 <>{} 1496-1 /../Advanced setup Ent. access code Tag description 001-FT-102 Def. access code Max. A0029563-EN A message is displayed if the value entered is outside the permitted value range. 54 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options Ent. access code Invalid or out of range input value Min:0 Max:9999 A0014049-EN 8.3.10 User roles and related access authorization The two user roles "Operator" and "Maintenance" have different write access to the parameters if the customer defines a user-specific access code. This protects the device configuration via the local display from unauthorized access → 114. Defining access authorization for user roles An access code is not yet defined when the device is delivered from the factory. Access authorization (read and write access) to the device is not restricted and corresponds to the "Maintenance" user role. ‣ Define the access code. The "Operator" user role is redefined in addition to the "Maintenance" user role. Access authorization differs for the two user roles. Access authorization to parameters: "Maintenance" user role Access code status Read access Write access An access code has not yet been defined (factory setting). After an access code has been defined. 1) 1) The user only has write access after entering the access code. Access authorization to parameters: "Operator" user role Access code status After an access code has been defined. 1) Read access Write access – 1) Despite the defined access code, certain parameters can always be modified and thus are excluded from the write protection as they do not affect the measurement: write protection via access code → 114 The user role with which the user is currently logged on is indicated by the Access status display parameter. Navigation path: Operation → Access status display 8.3.11 Disabling write protection via access code If the -symbol appears on the local display in front of a parameter, the parameter is write-protected by a user-specific access code and its value cannot be changed at the moment using local operation → 114. Parameter write protection via local operation can be disabled by entering the user-specific access code in the Enter access code parameter (→ 104) via the respective access option. Endress+Hauser 1. After you press , the input prompt for the access code appears. 2. Enter the access code. The -symbol in front of the parameters disappears; all previously writeprotected parameters are now re-enabled. 55 Operation options Proline Prosonic Flow I 400 Modbus RS485 8.3.12 Enabling and disabling the keypad lock The keypad lock makes it possible to block access to the entire operating menu via local operation. As a result, it is no longer possible to navigate through the operating menu or change the values of individual parameters. Users can only read the measured values on the operational display. The keypad lock is switched on and off via the context menu. Switching on the keypad lock The keypad lock is switched on automatically: • If the device has not been operated via the display for > 1 minute. • Each time the device is restarted. To activate the keylock manually: 1. The device is in the measured value display. Press the and keys for 3 seconds. A context menu appears. 2. In the context menu select the Keylock on option. The keypad lock is switched on. If the user attempts to access the operating menu while the keypad lock is active, the Keylock on message appears. Switching off the keypad lock ‣ The keypad lock is switched on. Press the and keys for 3 seconds. The keypad lock is switched off. 8.4 Access to operating menu via web browser 8.4.1 Function range With the integrated web server, the device can be operated and configured via a web browser service interface (CDI-RJ45) or WLAN interface. The structure of the operating menu is the same as for the local display. In addition to the measured values, status information on the device is displayed and can be used to monitor device health. Furthermore the device data can be managed and the network parameters can be configured. For additional information on the web server, see the Special Documentation for the device. → 169 56 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8.4.2 Operation options Requirements Computer hardware Hardware Interface CDI-RJ45 WLAN Interface The computer must have a RJ45 interface. 1) The operating unit must have a WLAN interface. Connection Standard Ethernet cable Connection via Wireless LAN. Screen Recommended size: ≥12" (depends on the screen resolution) 1) Recommended cable: CAT5e, CAT6 or CAT7, with shielded plug (e.g. YAMAICHI product; part no. YConProfixPlug63/Prod. ID: 82-006660) Computer software Software Interface CDI-RJ45 Recommended operating systems WLAN • Microsoft Windows 8 or higher. • Mobile operating systems: • iOS • Android Microsoft Windows XP and Windows 7 is supported. Web browsers supported • Microsoft Internet Explorer 8 or higher • Microsoft Edge • Mozilla Firefox • Google Chrome • Safari Computer settings Settings Interface CDI-RJ45 WLAN User rights Appropriate user rights (e.g. administrator rights) for TCP/IP and proxy server settings are necessary (e.g. for adjusting the IP address, subnet mask etc.). Proxy server settings of the web browser The web browser setting Use a proxy server for your LAN must be disabled . JavaScript JavaScript must be enabled. JavaScript must be enabled. WLAN display The requires JavaScript If JavaScript cannot be enabled: Enter http://192.168.1.212/servlet/ basic.html in the address bar of the web browser. A fully functional but simplified version of the operating menu structure starts in the web browser. support. installing a new firmware version: When To enable correct data display, clear the temporary memory (cache) under Internet options in the web browser. Network connections Only use the active network connections to the measuring device. Switch off all other network connections such as WLAN for example. Switch off all other network connections. In the event of connection problems: → 126 Endress+Hauser 57 Operation options Proline Prosonic Flow I 400 Modbus RS485 Measuring device: Via CDI-RJ45 service interface Device CDI-RJ45 service interface Measuring device The measuring device has an RJ45 interface. Web server Web server must be enabled; factory setting: ON For information on enabling the Web server → 62 Measuring device: via WLAN interface Device WLAN interface Measuring device The measuring device has a WLAN antenna: Transmitter with integrated WLAN antenna Web server Web server and WLAN must be enabled; factory setting: ON For information on enabling the Web server → 62 8.4.3 Connecting the device Via service interface (CDI-RJ45) Preparing the measuring device Configuring the Internet protocol of the computer The following information refers to the default Ethernet settings of the device. IP address of the device: 192.168.1.212 (factory setting) 1. Switch on the measuring device. 2. Connect the computer to the RJ45 plug via the standard Ethernet cable . 3. If a 2nd network card is not used, close all the applications on the notebook. Applications requiring Internet or a network, such as e-mail, SAP applications, Internet or Windows Explorer. 4. Close any open Internet browsers. 5. Configure the properties of the Internet protocol (TCP/IP) as defined in the table: IP address 192.168.1.XXX; for XXX all numerical sequences except: 0, 212 and 255 → e.g. 192.168.1.213 Subnet mask 255.255.255.0 Default gateway 192.168.1.212 or leave cells empty Via WLAN interface Configuring the Internet protocol of the mobile terminal NOTICE If the WLAN connection is lost during the configuration, settings made may be lost. ‣ Make sure that the WLAN connection is not disconnected while configuring the device. 58 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options NOTICE Note the following to avoid a network conflict: ‣ Avoid accessing the measuring device simultaneously from the same mobile terminal via the service interface (CDI-RJ45) and the WLAN interface. ‣ Only activate one service interface (CDI-RJ45 or WLAN interface). ‣ If simultaneous communication is necessary: configure different IP address ranges, e.g. 192.168.0.1 (WLAN interface) and 192.168.1.212 (CDI-RJ45 service interface). Preparing the mobile terminal ‣ Enable WLAN on the mobile terminal. Establishing a WLAN connection from the mobile terminal to the measuring device 1. In the WLAN settings of the mobile terminal: Select the measuring device using the SSID (e.g. EH_Prosonic Flow_400_A802000). 2. If necessary, select the WPA2 encryption method. 3. Enter the password: Serial number of the measuring device ex-works (e.g. L100A802000). The LED on the display module flashes. It is now possible to operate the measuring device with the web browser, FieldCare or DeviceCare. The serial number can be found on the nameplate. To ensure the safe and swift assignment of the WLAN network to the measuring point, it is advisable to change the SSID name. It should be possible to clearly assign the new SSID name to the measuring point (e.g. tag name) because it is displayed as the WLAN network. Terminating the WLAN connection ‣ After configuring the device: Terminate the WLAN connection between the mobile terminal and measuring device. Starting the web browser 1. Endress+Hauser Start the web browser on the computer. 59 Operation options Proline Prosonic Flow I 400 Modbus RS485 2. Enter the IP address of the web server in the address line of the web browser: 192.168.1.212 The login page appears. 2 3 4 1 5 Device name: Device tag: Signal Status: Web server language i English 6 Maintenance 7 Login Access Status Enter access code 8 i Login Reset access code 9 10 A0053670 1 2 3 4 5 6 7 8 9 10 Picture of device Device name Device tag Status signal Current measured values Operating language User role Access code Login Reset access code (→ 112) If a login page does not appear, or if the page is incomplete → 126 8.4.4 Logging on 1. Select the preferred operating language for the Web browser. 2. Enter the user-specific access code. 3. Press OK to confirm your entry. Access code 0000 (factory setting); can be changed by customer If no action is performed for 10 minutes, the Web browser automatically returns to the login page. 60 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8.4.5 Operation options User interface 1 2 3 A0029418 1 2 3 Function row Local display language Navigation area Header The following information appears in the header: • Device name • Device tag • Device status with status signal → 132 • Current measured values Function row Functions Meaning Measured values Displays the measured values of the device Menu • Access to the operating menu from the measuring device • The structure of the operating menu is the same as for the local display information on the operating menu structure: Description of Device Detailed Parameters Device status Displays the diagnostic messages currently pending, listed in order of priority Data management Data exchange between computer and measuring device: • Device configuration: • Load settings from the device (XML format, save configuration) • Save settings to the device (XML format, restore configuration) • Logbook - Export Event logbook (.csv file) • Documents - Export documents: • Export backup data record (.csv file, create documentation of the measuring point configuration) • Verification report (PDF file, only available with the "Heartbeat Verification" application package) Network Configuration and checking of all the parameters required for establishing the connection to the measuring device: • Network settings (e.g. IP address, MAC address) • Device information (e.g. serial number, firmware version) Logout End the operation and call up the login page Navigation area The menus, the associated submenus and parameters can be selected in the navigation area. Endress+Hauser 61 Operation options Proline Prosonic Flow I 400 Modbus RS485 Working area Depending on the selected function and the related submenus, various actions can be performed in this area: • Configuring parameters • Reading measured values • Calling up help text • Starting an upload/download 8.4.6 Disabling the Web server The Web server of the measuring device can be switched on and off as required using the Web server functionality parameter. Navigation "Expert" menu → Communication → Web server Parameter overview with brief description Parameter Web server functionality Description Switch the Web server on and off. Selection • Off • On Function scope of the "Web server functionality" parameter Option Description Off • The Web server is completely disabled. • Port 80 is locked. On • The complete Web server functionality is available. • JavaScript is used. • The password is transferred in an encrypted state. • Any change to the password is also transferred in an encrypted state. Enabling the Web server If the Web server is disabled it can only be re-enabled with the Web server functionality parameter via the following operating options: • Via local display • Via Bedientool "FieldCare" • Via "DeviceCare" operating tool 8.4.7 Logging out Before logging out, perform a data backup via the Data management function (upload configuration from device) if necessary. 1. Select the Logout entry in the function row. The home page with the Login box appears. 2. Close the Web browser. 3. If no longer needed: Reset the modified properties of the Internet protocol (TCP/IP) → 58. 8.5 Access to the operating menu via the operating tool The structure of the operating menu in the operating tools is identical to operation via the local display. 62 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 8.5.1 Operation options Connecting the operating tool Via Modbus RS485 protocol This communication interface is available in device versions with a Modbus RS485 output. 3 1 2 A0029437 17 1 2 3 Options for remote operation via Modbus RS485 protocol (active) Control system (e.g. PLC) Computer with web browser (e.g. Microsoft Edge) to access the integrated device web server or with operating tool (e.g. FieldCare, DeviceCare) with COM DTM "CDI Communication TCP/IP" or Modbus DTM Transmitter Via service interface (CDI-RJ45) 1 open press 3 2 A0029163 18 1 2 3 Connection via service interface (CDI-RJ45) Computer with web browser (e.g. Microsoft Internet Explorer, Microsoft Edge) for accessing the integrated device web server or with operating tool "FieldCare", "DeviceCare" with COM DTM "CDI Communication TCP/IP" or Modbus DTM Standard Ethernet connecting cable with RJ45 plug Service interface (CDI-RJ45) of the measuring device with access to the integrated web server Via WLAN interface The optional WLAN interface is available on the following device version: Order code for "Display; operation", option G "4-line, illuminated; touch control + WLAN" Endress+Hauser 63 Operation options Proline Prosonic Flow I 400 Modbus RS485 2 1 4 5 3 6 A0043149 1 2 3 4 5 6 Transmitter with integrated WLAN antenna LED lit constantly: WLAN reception is enabled on measuring device LED flashing: WLAN connection established between operating unit and measuring device Computer with WLAN interface and web browser (e.g. Microsoft Internet Explorer, Microsoft Edge) for accessing the integrated device web server or with operating tool (e.g. FieldCare, DeviceCare) Mobile handheld terminal with WLAN interface and web browser (e.g. Microsoft Internet Explorer, Microsoft Edge) for accessing the integrated device web server or operating tool (e.g. FieldCare, DeviceCare) Smart phone or tablet (e.g. Field Xpert SMT70) Function WLAN: IEEE 802.11 b/g (2.4 GHz) Encryption WPA2-PSK AES-128 (in accordance with IEEE 802.11i) Configurable WLAN channels 1 to 11 Degree of protection IP67 Available antenna Internal antenna Range Typically 10 m (32 ft) Configuring the Internet protocol of the mobile terminal NOTICE If the WLAN connection is lost during the configuration, settings made may be lost. ‣ Make sure that the WLAN connection is not disconnected while configuring the device. NOTICE Note the following to avoid a network conflict: ‣ Avoid accessing the measuring device simultaneously from the same mobile terminal via the service interface (CDI-RJ45) and the WLAN interface. ‣ Only activate one service interface (CDI-RJ45 or WLAN interface). ‣ If simultaneous communication is necessary: configure different IP address ranges, e.g. 192.168.0.1 (WLAN interface) and 192.168.1.212 (CDI-RJ45 service interface). Preparing the mobile terminal ‣ Enable WLAN on the mobile terminal. Establishing a WLAN connection from the mobile terminal to the measuring device 64 1. In the WLAN settings of the mobile terminal: Select the measuring device using the SSID (e.g. EH_Prosonic Flow_400_A802000). 2. If necessary, select the WPA2 encryption method. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 3. Operation options Enter the password: Serial number of the measuring device ex-works (e.g. L100A802000). The LED on the display module flashes. It is now possible to operate the measuring device with the web browser, FieldCare or DeviceCare. The serial number can be found on the nameplate. To ensure the safe and swift assignment of the WLAN network to the measuring point, it is advisable to change the SSID name. It should be possible to clearly assign the new SSID name to the measuring point (e.g. tag name) because it is displayed as the WLAN network. Terminating the WLAN connection ‣ After configuring the device: Terminate the WLAN connection between the mobile terminal and measuring device. 8.5.2 FieldCare Function range FDT-based (Field Device Technology) plant asset management tool from Endress+Hauser. It can configure all smart field units in a system and helps you manage them. By using the status information, it is also a simple but effective way of checking their status and condition. Access is via: Typical functions: • Transmitter parameter configuration • Loading and saving of device data (upload/download) • Documentation of the measuring point • Visualization of the measured value memory (line recorder) and event logbook • Operating Instructions BA00027S • Operating Instructions BA00059S Source for device description files → 68 Establishing a connection • Operating Instructions BA00027S • Operating Instructions BA00059S Endress+Hauser 65 Operation options Proline Prosonic Flow I 400 Modbus RS485 User interface 1 3 2 4 Pro... Pro... Pro... 6 5 A0008200 1 2 3 4 5 6 Device name Device tag Status area with status signal → 132 Display area for current measured values Editing toolbar with other functions Navigation area with operating menu structure 8.5.3 DeviceCare Function range Tool for connecting and configuring Endress+Hauser field devices. The fastest way to configure Endress+Hauser field devices is with the dedicated "DeviceCare" tool. Together with the device type managers (DTMs) it presents a convenient, comprehensive solution. Innovation brochure IN01047S Source for device description files → 68 8.5.4 Field Xpert SMT70, SMT77 Field Xpert SMT70 The Field Xpert SMT70 tablet PC for device configuration enables mobile plant asset management in hazardous and non-hazardous areas. It is suitable for commissioning and maintenance staff to manage field instruments with a digital communication interface and to record progress. This tablet PC is designed as an all-in-one solution with a preinstalled driver library and is an easy-to-use, touch-sensitive tool which can be used to manage field instruments throughout their entire life cycle. • Technical Information TI01342S • Operating Instructions BA01709S • Product page: www.endress.com/smt70 Source for device description files → 68 66 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation options Field Xpert SMT77 The Field Xpert SMT77 tablet PC for device configuration enables mobile plant asset management in areas categorized as Ex Zone 1. • Technical Information TI01418S • Operating Instructions BA01923S • Product page: www.endress.com/smt77 Source for device description files → 68 Endress+Hauser 67 System integration Proline Prosonic Flow I 400 Modbus RS485 9 System integration 9.1 Overview of device description files 9.1.1 Current version data for the device Firmware version • On the title page of the manual • On the transmitter nameplate • Firmware version Diagnostics → Device information → Firmware version Release date of firmware version --- For an overview of the various firmware versions for the device → 144 9.1.2 Operating tools The suitable device description file for the individual operating tools is listed in the table below, along with information on where the file can be acquired. FieldCare • www.endress.com → Downloads area • USB stick (contact Endress+Hauser) • DVD (contact Endress+Hauser) DeviceCare • www.endress.com → Downloads area • CD–ROM (contact Endress+Hauser) • DVD (contact Endress+Hauser) 9.2 Compatibility with previous model If the device is replaced, the measuring device Prosonic Flow supports the compatibility of the Modbus registers for the process variables and the diagnostic information with the previous model Prosonic Flow 93. It is not necessary to change the engineering parameters in the automation system. Compatible Modbus registers: process variables Process variable Compatible Modbus registers Mass flow 2007 Volume flow 2009 Totalizer 1 2610 Totalizer 2 2810 Totalizer 3 3010 Compatible Modbus registers: diagnostic information Diagnostic information Compatible Modbus registers Diagnostic code (data type: String), e.g. F270 6821 Diagnostic number (data type: Integer), e.g. 270 6859 The Modbus registers are compatible but the diagnostic numbers are not. Overview of the new diagnostic numbers → 135 68 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 System integration 9.3 Modbus RS485 information 9.3.1 Function codes Function codes are used to define which read or write action is carried out via the Modbus protocol. The measuring device supports the following function codes: Code 03 Name Read holding register Description Application Master reads one or more Modbus registers from the device. A maximum of 125 consecutive registers can be read with 1 telegram: 1 register = 2 bytes Read device parameters with read and write access Example: Read volume flow measuring device does The not make a distinction between function codes 03 and 04; these codes therefore yield the same result. 04 Read input register Master reads one or more Modbus registers from the device. A maximum of 125 consecutive registers can be read with 1 telegram: 1 register = 2 bytes Read device parameters with read access Example: Read totalizer value measuring device does The not make a distinction between function codes 03 and 04; these codes therefore yield the same result. 06 Write single registers Master writes a new value to one Modbus register of the measuring device. Write only 1 device parameter Example: reset totalizer function code 16 to write Use multiple registers with just 1 telegram. 08 Diagnostics Master checks the communication connection to the measuring device. The following "Diagnostics codes" are supported: • Sub-function 00 = Return query data (loopback test) • Sub-function 02 = Return diagnostics register Endress+Hauser 69 System integration Proline Prosonic Flow I 400 Modbus RS485 Code 16 Name Description Write multiple registers Application Master writes a new value to multiple Modbus registers of the device. A maximum of 120 consecutive registers can be written with 1 telegram. Write multiple device parameters the required device Ifparameters are not available as a group, yet must nevertheless be addressed with a single telegram, use Modbus data map → 71 23 Read/Write multiple registers Master reads and writes a maximum of 118 Modbus registers of the measuring device simultaneously with 1 telegram. Write access is executed before read access. Write and read multiple device parameters Example: • Read mass flow • Reset totalizer Broadcast messages are only allowed with function codes 06, 16 and 23. 9.3.2 Register information For an overview of device parameters with their respective Modbus register information, please refer to the "Modbus RS485 register information" section in the "Description of device parameters" documentation → 169. 9.3.3 Response time Response time of the measuring device to the request telegram of the Modbus master: typically 3 to 5 ms 9.3.4 Data types The measuring device supports the following data types: FLOAT (floating point number IEEE 754) Data length = 4 bytes (2 registers) Byte 3 Byte 2 Byte 1 Byte 0 SEEEEEEE EMMMMMMM MMMMMMMM MMMMMMMM S = sign, E = exponent, M = mantissa INTEGER Data length = 2 bytes (1 register) Byte 1 Byte 0 Most significant byte (MSB) Least significant byte (LSB) STRING Data length = depends on the device parameter, e.g. presentation of a device parameter with a data length = 18 bytes (9 registers) Byte 17 Most significant byte (MSB) 70 Byte 16 ... ... Byte 1 Byte 0 Least significant byte (LSB) Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 9.3.5 System integration Byte transmission sequence Byte addressing, i.e. the transmission sequence of the bytes, is not specified in the Modbus specification. For this reason, it is important to coordinate or match the addressing method between the master and slave during commissioning. This can be configured in the measuring device using the Byte order parameter. The bytes are transmitted depending on the selection in the Byte order parameter: FLOAT Sequence Options 1. 2. 3. 4. 1–0–3–2* Byte 1 (MMMMMMMM) Byte 0 (MMMMMMMM) Byte 3 (SEEEEEEE) Byte 2 (EMMMMMMM) 0–1–2–3 Byte 0 (MMMMMMMM) Byte 1 (MMMMMMMM) Byte 2 (EMMMMMMM) Byte 3 (SEEEEEEE) 2–3–0–1 Byte 2 (EMMMMMMM) Byte 3 (SEEEEEEE) Byte 0 (MMMMMMM) Byte 1 (MMMMMMM) 3–2–1–0 Byte 3 (SEEEEEEE) Byte 2 (EMMMMMMM) Byte 1 (MMMMMMMM) Byte 0 (MMMMMMMM) * = factory setting, S = sign, E = exponent, M = mantissa INTEGER Sequence Options 1. 2. 1–0–3–2* 3–2–1–0 Byte 1 (MSB) Byte 0 (LSB) 0–1–2–3 2–3–0–1 Byte 0 (LSB) Byte 1 (MSB) * = factory setting, MSB = most significant byte, LSB = least significant byte STRING Presentation taking the example of a device parameter with a data length of 18 bytes. Sequence Options 1. 2. ... 17. 18. 1–0–3–2* 3–2–1–0 Byte 17 (MSB) Byte 16 ... Byte 1 Byte 0 (LSB) 0–1–2–3 2–3–0–1 Byte 16 Byte 17 (MSB) ... Byte 0 (LSB) Byte 1 * = factory setting, MSB = most significant byte, LSB = least significant byte 9.3.6 Modbus data map Function of the Modbus data map The device offers a special memory area, the Modbus data map (for a maximum of 16 device parameters), to allow users to call up multiple device parameters via Modbus RS485 and not only individual device parameters or a group of consecutive device parameters. Grouping of device parameters is flexible and the Modbus master can read or write to the entire data block simultaneously with a single request telegram. Endress+Hauser 71 System integration Proline Prosonic Flow I 400 Modbus RS485 Structure of the Modbus data map The Modbus data map consists of two data sets: • Scan list: Configuration area The device parameters to be grouped are defined in a list by entering their Modbus RS485 register addresses in the list. • Data area The measuring device reads out the register addresses entered in the scan list cyclically and writes the associated device data (values) to the data area. For an overview of device parameters with their respective Modbus register information, please refer to the "Modbus RS485 register information" section in the "Description of device parameters" documentation → 169. Scan list configuration For configuration, the Modbus RS485 register addresses of the device parameters to be grouped must be entered in the scan list. Please note the following basic requirements of the scan list: Max. entries 16 device parameters Supported device parameters Only parameters with the following characteristics are supported: • Access type: read or write access • Data type: float or integer Configuration of the scan list via FieldCare or DeviceCare Carried out using the operating menu of the measuring device: Expert → Communication → Modbus data map → Scan list register 0 to 15 Scan list No. Configuration register 0 Scan list register 0 ... ... 15 Scan list register 15 Configuration of the scan list via Modbus RS485 Carried out using register addresses 5001 - 5016 Scan list No. Modbus RS485 register Data type Configuration register 0 5001 Integer Scan list register 0 ... ... Integer ... 15 5016 Integer Scan list register 15 Reading out data via Modbus RS485 The Modbus master accesses the data area of the Modbus data map to read out the current values of the device parameters defined in the scan list. Master access to data area 72 Via register addresses 5051-5081 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 System integration Data area Device parameter value Modbus RS485 register Data type* Access** Start register End register (Float only) Value of scan list register 0 5051 5052 Integer/float read/write Value of scan list register 1 5053 5054 Integer/float read/write Value of scan list register ... ... ... ... ... Value of scan list register 15 5081 5082 Integer/float read/write * Data type depends on the device parameters entered in the scan list. ** Data access depends on the device parameters entered in the scan list. If the device parameter entered supports read and write access, the parameter can also be accessed via the data area. Endress+Hauser 73 Commissioning Proline Prosonic Flow I 400 Modbus RS485 10 Commissioning 10.1 Post-mounting and post-connection check Before commissioning the device: ‣ Make sure that the post-installation and post-connection checks have been performed successfully. • Checklist for "Post-mounting" check→ 32 • Checklist for "Post-connection check" → 41 10.2 Switching on the measuring device ‣ Switch on the device upon successful completion of the post-mounting and post- connection check. After a successful startup, the local display switches automatically from the startup display to the operational display. • If nothing appears on the local display or if a diagnostic message is displayed, refer to the section on "Diagnostics and troubleshooting" → 126. • If diagnostic information 104, 105 or 106 appears on the local display, then the measuring point is not yet correctly mounted/configured → 135. 10.3 Setting the operating language Factory setting: English or ordered local language XXXXXXXXX 20.50 XX 1. XX Main menu Display language 0104-1 English Operation Setup 2. Display language à English Deutsch Español Français 3. 4. 0104-1 Display language à English Deutsch Español Français Hauptmenü Sprache 0104-1 0104-1 Deutsch Betrieb Setup A0029420 19 10.4 Taking the example of the local display Configuring the measuring device The Setup menu with its guided wizards contains all the parameters needed for standard operation. 74 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning XXXXXXXXX 20.50 mA 1. Main menu Display language English Display/operat. Setup 2. Main menu Display/operat. Setup Diagnostic 3. / ../Setup Medium selection XXXXXXXXX XXXXXXXXX A0032222-EN 20 Navigation to "Setup" menu using the example of the local display The number of submenus and parameters can vary depending on the device version. Certain submenus and parameters in these submenus are not described in the Operating Instructions. Instead a description is provided in the Special Documentation for the device ("Supplementary documentation"→ 168). Navigation "Setup" menu Setup Endress+Hauser Device tag (7157) → 81 ‣ System units → 81 Volume flow unit (0553) → 81 Volume unit (0563) → 81 Mass flow unit (0554) → 82 Mass unit (0574) → 82 Velocity unit (0566) → 82 Temperature unit (0557) → 82 Density unit (0555) → 82 Length unit (0551) → 82 75 Commissioning Proline Prosonic Flow I 400 Modbus RS485 ‣ Communication → 82 Bus address (7112) → 83 Baudrate (7111) → 83 Data transfer mode (7115) → 83 Parity (7122) → 83 Byte order (7113) → 83 Failure mode (7116) → 83 ‣ Measuring point 76 → 83 Measuring point configuration (5675) → 85 Medium (2926) → 85 Medium temperature (3053) → 85 Sound velocity (2929) → 85 Viscosity (2932) → 85 Pipe material (2927) → 85 Pipe sound velocity (2933) → 85 Pipe dimensions (2943) → 85 Pipe circumference (2934) → 85 Pipe outer diameter (2910) → 86 Pipe wall thickness (2916) → 86 Liner material (2928) → 86 Liner sound velocity (2936) → 86 Liner thickness (2935) → 86 Sensor type (2924) → 86 Sensor coupling (2957) → 86 Mounting type (2938) → 86 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Cable length (2939) → 86 FlowDC inlet configuration (3049) → 87 Intermediate pipe length (2945) → 87 Inlet diameter (3054) → 87 Transition length (3065) → 87 Inlet run (3050) → 87 Relative sensor position (2985) → 87 Result sensor type / mounting type (2946) → 87 Result sensor distance / measuring aid (2947) → 87 Result sensor type / sensor distance (3066) → 87 Result path length / arc length (3067) → 87 ‣ Installation status → 88 Installation status (2958) → 88 Signal strength (2914) → 88 Signal to noise ratio (2917) → 88 Sound velocity (2915) → 88 Sound velocity deviation (2986) → 88 ‣ Current output 1 Endress+Hauser Commissioning → 89 Process variable current output (0359–1) → 89 Current range output (0353–1) → 89 Lower range value output (0367–1) → 90 Upper range value output (0372–1) → 90 Fixed current (0365–1) → 90 77 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Damping current output (0363–1) → 90 Failure behavior current output (0364–1) → 90 Failure current (0352–1) → 90 ‣ Pulse/frequency/switch output → 90 ‣ Display → 99 Format display (0098) → 100 Value 1 display (0107) → 100 0% bargraph value 1 (0123) → 100 100% bargraph value 1 (0125) → 100 Value 2 display (0108) → 100 Value 3 display (0110) → 101 0% bargraph value 3 (0124) → 101 100% bargraph value 3 (0126) → 101 Value 4 display (0109) → 101 ‣ Low flow cut off → 101 Assign process variable (1837) → 102 On value low flow cutoff (1805) → 102 Off value low flow cutoff (1804) → 102 ‣ Advanced setup → 103 ‣ Sensor adjustment Installation direction (1809) ‣ Totalizer 1 to n 78 → 104 → 104 → 104 Assign process variable 1 to n (0914–1 to n) → 105 Process variable unit 1 to n (0915–1 to n) → 105 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Totalizer 1 to n operation mode (0908–1 to n) → 105 Totalizer 1 to n failure behavior (0901–1 to n) → 105 ‣ Display ‣ WLAN settings Endress+Hauser → 106 Format display (0098) → 107 Value 1 display (0107) → 107 0% bargraph value 1 (0123) → 107 100% bargraph value 1 (0125) → 107 Decimal places 1 (0095) → 107 Value 2 display (0108) → 107 Decimal places 2 (0117) → 107 Value 3 display (0110) → 107 0% bargraph value 3 (0124) → 107 100% bargraph value 3 (0126) → 107 Decimal places 3 (0118) → 107 Value 4 display (0109) → 108 Decimal places 4 (0119) → 108 Display language (0104) → 108 Display interval (0096) → 108 Display damping (0094) → 108 Header (0097) → 108 Header text (0112) → 108 Separator (0101) → 108 Backlight (0111) → 108 → 108 79 Commissioning Proline Prosonic Flow I 400 Modbus RS485 WLAN (2702) → 109 WLAN mode (2717) → 109 SSID name (2714) → 109 Network security (2705) → 109 Security identification (2718) → 109 User name (2715) → 109 WLAN password (2716) → 109 WLAN IP address (2711) → 109 WLAN MAC address (2703) → 110 WLAN passphrase (2706) → 110 WLAN MAC address (2703) → 110 Assign SSID name (2708) → 110 SSID name (2707) → 110 Connection state (2722) → 110 Received signal strength (2721) → 110 ‣ Heartbeat setup → 110 ‣ Heartbeat base settings Plant operator (2754) → 111 Location (2755) → 111 ‣ Administration → 111 ‣ Define access code → 111 Define access code → 112 Confirm access code → 112 ‣ Reset access code 80 → 111 → 112 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Operating time (0652) → 112 Reset access code (0024) → 112 → 112 Device reset (0000) Parameter overview with brief description Parameter Device tag Description User entry Enter the name for the measuring point. 10.4.1 Character string comprising numbers, letters and special characters (32) Setting the system units In the System units submenu the units of all the measured values can be set. Navigation "Setup" menu → System units ‣ System units Volume flow unit (0553) → 81 Volume unit (0563) → 81 Mass flow unit (0554) → 82 Mass unit (0574) → 82 Velocity unit (0566) → 82 Temperature unit (0557) → 82 Density unit (0555) → 82 Length unit (0551) → 82 Parameter overview with brief description Parameter Volume flow unit Description Select volume flow unit. Selection Unit choose list Country-specific: • m³/h • ft³/min Unit choose list Country-specific: • m³ • ft³ Result The selected unit applies to: • Output • Low flow cut off • Simulation process variable Volume unit Endress+Hauser Select volume unit. Factory setting 81 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Mass flow unit Description Select mass flow unit. Selection Factory setting Unit choose list Country-specific: • kg/h • lb/min Result The selected unit applies to: • Output • Low flow cut off • Simulation process variable Mass unit Select mass unit. Unit choose list Country-specific: • kg • lb Velocity unit Select velocity unit. Unit choose list Depends on country: • m/s • ft/s Unit choose list Country-specific: • °C • °F Unit choose list Country-specific: • kg/dm³ • lb/ft³ Unit choose list Country-specific: • mm • in Effect The selected unit applies to: • Flow velocity • Sound velocity Temperature unit Select temperature unit. Result The selected unit applies to: • Temperature • Electronic temperature parameter (6053) • External temperature parameter (6080) • Reference temperature parameter (1816) Density unit Select density unit. Result The selected unit applies to: • Output • Simulation process variable Length unit Select the unit of length. 10.4.2 Configuring the communication interface The Communication submenu guides you systematically through all the parameters that have to be configured for selecting and setting the communication interface. Navigation "Setup" menu → Communication ‣ Communication 82 Bus address → 83 Baudrate → 83 Data transfer mode → 83 Parity → 83 Byte order → 83 Failure mode → 83 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Parameter overview with brief description Parameter Description User entry / Selection Bus address Enter device address. 1 to 247 Baudrate Define data transfer speed. • 1200 BAUD • 2400 BAUD • 4800 BAUD • 9600 BAUD • 19200 BAUD • 38400 BAUD • 57600 BAUD • 115200 BAUD • 230400 BAUD Data transfer mode Select data transfer mode. • ASCII • RTU Parity Select parity bits. Picklist ASCII option: • 0 = Even option • 1 = Odd option Picklist RTU option: • 0 = Even option • 1 = Odd option • 2 = None / 1 stop bit option • 3 = None / 2 stop bits option Byte order Select byte transmission sequence. • 0-1-2-3 • 3-2-1-0 • 1-0-3-2 • 2-3-0-1 Failure mode Select measured value output behavior when a diagnostic message occurs via Modbus communication. • NaN value • Last valid value NaN 1) 1) Not a Number 10.4.3 Configuring the measuring point The "Measuring point " wizard guides you systematically through all the parameters that must be set for the configuration of the measuring point. Navigation "Setup" menu → Measuring point ‣ Measuring point Endress+Hauser Measuring point configuration (5675) → 85 Medium (2926) → 85 Medium temperature (3053) → 85 Sound velocity (2929) → 85 Viscosity (2932) → 85 Pipe material (2927) → 85 83 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Pipe sound velocity (2933) 84 Pipe dimensions (2943) → 85 Pipe circumference (2934) → 85 Pipe outer diameter (2910) → 86 Pipe wall thickness (2916) → 86 Liner material (2928) → 86 Liner sound velocity (2936) → 86 Liner thickness (2935) → 86 Sensor type (2924) → 86 Sensor coupling (2957) → 86 Mounting type (2938) → 86 Cable length (2939) → 86 FlowDC inlet configuration (3049) → 87 Intermediate pipe length (2945) → 87 Inlet diameter (3054) → 87 Transition length (3065) → 87 Inlet run (3050) → 87 Relative sensor position (2985) → 87 Result sensor type / mounting type (2946) → 87 Result sensor distance / measuring aid (2947) → 87 Result sensor type / sensor distance (3066) → 87 Result path length / arc length (3067) → 87 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Parameter overview with brief description Parameter Prerequisite Description Selection / User entry / User interface Factory setting Measuring point configuration – Select configuration for the measuring point. • 1 measuring point - signal path 1 • 1 measuring point - signal path 2 * • 1 measuring point - 2 signal paths * Medium – Select the medium. • Water – • Sea water • Distilled water • Ammonia NH3 • Benzene • Ethanol • Glycol • Milk • Methanol • User-specific liquid Medium temperature – Enter the medium temperature –200 to 550 °C for the installation. – Sound velocity The User-specific liquid option is selected in Medium parameter. Enter the medium's sound velocity for the installation. 200 to 3 000 m/s – Viscosity The User-specific liquid option is selected in Medium parameter. Enter medium viscosity at installation temperature. 0.01 to 10 000 mm²/ – s Pipe material – Select pipe material. • Carbon steel • Ductile cast iron • Stainless steel • 1.4301 (UNS S30400) • 1.4401 (UNS S31600) • 1.4550 (UNS S34700) • Hastelloy C • PVC • PE • LDPE • HDPE • GRP • PVDF • PA • PP • PTFE • Pyrex glass • Asbestos cement • Copper • Unknown pipe material Pipe sound velocity The Unknown pipe material option is selected in the Pipe material parameter. Enter sound velocity of pipe material. 800.0 to 3 800.0 m/s – Pipe dimensions – Select if pipe dimensions are defined by diameter or circumference. • Diameter – • Pipe circumference Pipe circumference The Pipe circumference option is selected in the Pipe dimensions parameter. Define the pipe circumference. 30 to 62 800 mm Endress+Hauser Depending on the sensor version – – 85 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry / User interface Factory setting Pipe outer diameter The Diameter option is selected in Pipe dimensions parameter. Define the outer diameter of the pipe. 0 to 20 000 mm – Pipe wall thickness – Enter the pipe wall thickness. Positive floating point number 3 mm Liner material – Select liner material. • None • Cement • Rubber • Epoxy resin • Unknown liner material – Liner sound velocity The Unknown liner material option is selected in the Liner material parameter. Define the sound velocity of liner material. 800.0 to 3 800.0 m/s – Liner thickness – Define the thickness of liner. 0 to 100 mm – Sensor type – Select sensor type. • C-030-A • C-050-A • C-100-A • C-100-B • C-100-C • C-200-A • C-200-B • C-200-C • C-500-A • I-100-A * – Pipe sound velocity The Unknown pipe material option is selected in the Pipe material parameter. Enter sound velocity of pipe material. 800.0 to 3 800.0 m/s – Sensor coupling The following option is selected in Sensor type parameter: Select coupling medium. • Coupling pad • Coupling paste – • C-030-A • C-050-A • C-100-A • C-100-B • C-100-C • C-200-A • C-200-B • C-200-C • C-500-A Mounting type – • 1 traverse • 2 traverses • 3 traverses • 4 traverses • (1) direct option: Sensor arrangement with 1 traverse • Automatic • (2) V-mounting option: Sensor arrangement with 2 traverses • (3) Z-Mounting option: Sensor arrangement with 3 traverses • (4) W-mounting option: Sensor arrangement with 4 traverses Automatic Cable length – Enter length of sensor cables. As per order 86 Select the number of traverses (number of times the signal passes through the medium). 0 to 200 000 mm Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Commissioning Description Selection / User entry / User interface Factory setting FlowDC inlet configuration The 1 measuring point - 2 signal paths option is selected in Measuring point configuration parameter. Select FlowDC inlet configuration. • Off • Single elbow • Double elbow • Double elbow 3D • 45° bend • 2 x 45° bend • Concentric diameter change • Other * – Intermediate pipe length The 1 measuring point - 2 signal paths option is selected in Measuring point configuration parameter. Enter the length of the intermediate pipe between the two bends. Positive floatingpoint number – Inlet diameter • The 1 measuring point - 2 signal paths option is selected in the Measuring point configuration parameter. • The Concentric diameter change option is selected in the Inlet configuration parameter. Enter the outer diameter of the 1 to 10 000 mm pipe before the cross-section change. For convenience, the same measuring pipe wall thickness as for the clamp-on system is applied. – Transition length • In the Measuring point configuration parameter, the 1 measuring point - 2 signal paths option is selected. • In the Inlet configuration parameter, the Concentric diameter change option is selected. Enter length of the concentric diameter change. 0 to 20 000 mm – Inlet run The 1 measuring point - 2 signal paths option is selected in Measuring point configuration parameter. Enter length of the available straight inlet run. 0 to 300 000 mm – Relative sensor position The 1 measuring point - 2 Shows the correct position for signal paths option is selected the sensor. in the Measuring point configuration parameter and the Off option is not selected in FlowDC inlet configuration parameter. • 90° • 180° – Result sensor type / mounting type – Shows the selected sensor type e.g. C-100-A option / – and (if applicable (2) V-mounting automatically) selected option mounting type. Result sensor distance / measuring aid – Shows the calculated sensor distance and vernier or wire length (if applicable) required for installation. e.g. 201.3 mm / B 21 – Result sensor type / sensor distance – Shows the sensor type and sensor distance calculated for installation. e.g. I-100-A / 500 mm – Result path length / arc length – Shows the path length calculated and (if applicable) the calculated arc length. e.g. 1 085 mm / 257.56 mm – * Visibility depends on order options or device settings Endress+Hauser 87 Commissioning Proline Prosonic Flow I 400 Modbus RS485 10.4.4 Checking the installation status The status of individual parameters can be checked in the Installation status submenu. Navigation "Setup" menu → Installation status ‣ Installation status Installation status (2958) → 88 Signal strength (2914) → 88 Signal to noise ratio (2917) → 88 Sound velocity (2915) → 88 Sound velocity deviation (2986) → 88 Parameter overview with brief description Parameter Installation status Description Shows the device status on installation based on the measured values displayed. Displays the device status after installation according to the displayed measured values. • Good option: No further optimization required • Acceptable option: Measuring performance ok, optimize if possible. You should always aim for the status Good option. • Bad option: Optimization is required. Poor and unstable measuring performance. User interface • Good • Acceptable • Bad the following points to optimize the sensor Check installation: • Sensor distance • Alignment of sensors • Check the measuring point parameters in the configuration Signal strength Displays the current signal strength (0 to 100 dB). Signed floating-point number Assessment of the signal strength: • < 10 dB: bad • > 90 dB: very good Signal to noise ratio Displays the current signal to noise ratio (0 to 100 dB). Signed floating-point number Assessment of the signal-to-noise ratio: • < 20 dB: bad • > 50 dB: very good Sound velocity Displays the sound velocity that is currently measured. Signed floating-point number Deviation of the measured sound velocity from the expected sound velocity: • < 1 %: good • 1 to 2 %: acceptable • > 2 %: bad Sound velocity deviation 88 Shows the deviation of the installation sound velocity from the measured sound velocity. Signed floating-point number Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 10.4.5 Commissioning Configuring the current output The Current output wizard guides you systematically through all the parameters that have to be set for configuring the current output. Navigation "Setup" menu → Current output 1 ‣ Current output 1 Process variable current output (0359–1) → 89 Current range output (0353–1) → 89 Lower range value output (0367–1) → 90 Upper range value output (0372–1) → 90 Fixed current (0365–1) → 90 Damping current output (0363–1) → 90 Failure behavior current output (0364–1) → 90 Failure current (0352–1) → 90 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Process variable current output – Select the process variable for the current output. • Off * • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * • Electronics temperature Current range output – Select current range for process value output and upper/lower level for alarm signal. • 4...20 mA NE Depends on country: (3.8...20.5 mA) • 4...20 mA NE • 4...20 mA US (3.8...20.5 mA) (3.9...20.8 mA) • 4...20 mA US • 4...20 mA (4...20.5 (3.9...20.8 mA) mA) • 0...20 mA (0...20.5 mA) • Fixed value Endress+Hauser – 89 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry Factory setting Lower range value output In Current span parameter (→ 89), one of the following options is selected: • 4...20 mA NE (3.8...20.5 mA) • 4...20 mA US (3.9...20.8 mA) • 4...20 mA (4...20.5 mA) • 0...20 mA (0...20.5 mA) Enter lower range value for the Signed floating-point measured value range. number Depends on country: • m³/h • ft³/h Upper range value output In Current span parameter (→ 89), one of the following options is selected: • 4...20 mA NE (3.8...20.5 mA) • 4...20 mA US (3.9...20.8 mA) • 4...20 mA (4...20.5 mA) • 0...20 mA (0...20.5 mA) Enter upper range value for the measured value range. Signed floating-point number Depends on country and nominal diameter Fixed current The Fixed current option is selected in the Current span parameter (→ 89). Defines the fixed output current. 0 to 22.5 mA 22.5 mA Damping current output A process variable is selected in the Assign current output parameter (→ 89) and one of the following options is selected in the Current span parameter (→ 89): • 4...20 mA NE (3.8...20.5 mA) • 4...20 mA US (3.9...20.8 mA) • 4...20 mA (4...20.5 mA) • 0...20 mA (0...20.5 mA) Enter time constant for output damping (PT1 element). Damping reduces the effect of fluctuations in the measured value on the output signal. 0.0 to 999.9 s – Failure behavior current output A process variable is selected in the Assign current output parameter (→ 89) and one of the following options is selected in the Current span parameter (→ 89): • 4...20 mA NE (3.8...20.5 mA) • 4...20 mA US (3.9...20.8 mA) • 4...20 mA (4...20.5 mA) • 0...20 mA (0...20.5 mA) Select output behavior in the event of a device alarm. • Min. • Max. • Last valid value • Actual value • Fixed value – Failure current The Defined value option is selected in the Failure mode parameter. Enter current output value in alarm condition. 0 to 22.5 mA – * Visibility depends on order options or device settings 10.4.6 Configuring the pulse/frequency/switch output The Pulse/frequency/switch output wizard guides you systematically through all the parameters that can be set for configuring the selected output type. Navigation "Setup" menu → Pulse/frequency/switch output ‣ Pulse/frequency/switch output 90 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Endress+Hauser Commissioning Operating mode (0469) → 92 Assign pulse output (0460) → 92 Assign frequency output (0478) → 93 Switch output function (0481) → 95 Assign diagnostic behavior (0482) → 95 Assign limit (0483) → 95 Assign flow direction check (0484) → 96 Assign status (0485) → 96 Pulse scaling (0455) → 92 Pulse width (0452) → 92 Failure mode (0480) → 92 Minimum frequency value (0453) → 93 Maximum frequency value (0454) → 94 Measuring value at minimum frequency (0476) → 94 Measuring value at maximum frequency (0475) → 94 Failure mode (0451) → 94 Failure frequency (0474) → 94 Switch-on value (0466) → 96 Switch-off value (0464) → 96 Switch-on delay (0467) → 96 Switch-off delay (0465) → 96 Failure mode (0486) → 96 Invert output signal (0470) → 92 91 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Configuring the pulse output Navigation "Setup" menu → Pulse/frequency/switch output 1 to n ‣ Pulse/frequency/switch output 1 to n Operating mode → 92 Assign pulse output → 92 Value per pulse → 92 Pulse width → 92 Failure mode → 92 Invert output signal → 92 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Operating mode – Define the output as a pulse, frequency or switch output. • Pulse * • Frequency * • Switch * – Assign pulse output The Pulse option is selected in Operating mode parameter. Select process variable for pulse output. • Off • Volume flow • Mass flow – Pulse scaling The Pulse option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign pulse output parameter (→ 92). Enter quantity for measured value at which a pulse is output. Positive floating point number Depends on country and nominal diameter Pulse width The Pulse option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign pulse output parameter (→ 92). Define time width of the output pulse. 0.05 to 2 000 ms – Failure mode The Pulse option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign pulse output parameter (→ 92). Select output behavior in the event of a device alarm. • Actual value • No pulses – Invert output signal – Invert the output signal. • No • Yes – * 92 Visibility depends on order options or device settings Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Configuring the frequency output Navigation "Setup" menu → Pulse/frequency/switch output 1 to n ‣ Pulse/frequency/switch output 1 to n Operating mode → 93 Assign frequency output → 93 Minimum frequency value → 93 Maximum frequency value → 94 Measuring value at minimum frequency → 94 Measuring value at maximum frequency → 94 Failure mode → 94 Failure frequency → 94 Invert output signal → 94 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Operating mode – Define the output as a pulse, frequency or switch output. • Pulse * • Frequency * • Switch * – Assign frequency output The Frequency option is selected in Operating mode parameter (→ 92). Select process variable for frequency output. • Off • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Electronics temperature • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * – Minimum frequency value The Frequency option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign frequency output parameter (→ 93). Enter minimum frequency. 0.0 to 10 000.0 Hz – Endress+Hauser 93 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry Factory setting Maximum frequency value The Frequency option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign frequency output parameter (→ 93). Enter maximum frequency. 0.0 to 10 000.0 Hz – Measuring value at minimum frequency The Frequency option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign frequency output parameter (→ 93). Enter measured value for minimum frequency. Signed floating-point number Depends on country and nominal diameter Measuring value at maximum frequency The Frequency option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign frequency output parameter (→ 93). Enter measured value for maximum frequency. Signed floating-point number Depends on country and nominal diameter Failure mode The Frequency option is selected in the Operating mode parameter (→ 92) and a process variable is selected in the Assign frequency output parameter (→ 93). Select output behavior in the event of a device alarm. • Actual value • Defined value • 0 Hz – Failure frequency In the Operating mode parameter (→ 92), the Frequency option is selected, in the Assign frequency output parameter (→ 93) a process variable is selected, and in the Failure mode parameter, the Defined value option is selected. Enter frequency output value in alarm condition. 0.0 to 12 500.0 Hz – Invert output signal – Invert the output signal. • No • Yes – * Visibility depends on order options or device settings Configuring the switch output Navigation "Setup" menu → Pulse/frequency/switch output 1 to n ‣ Pulse/frequency/switch output 1 to n 94 Operating mode → 95 Switch output function → 95 Assign diagnostic behavior → 95 Assign limit → 95 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Assign flow direction check → 96 Assign status → 96 Switch-on value → 96 Switch-off value → 96 Switch-on delay → 96 Switch-off delay → 96 Failure mode → 96 Invert output signal → 96 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Operating mode – Define the output as a pulse, frequency or switch output. • Pulse * • Frequency * • Switch * – Switch output function The Switch option is selected in the Operating mode parameter. Select function for switch output. • Off • On • Diagnostic behavior • Limit • Flow direction check • Status – Assign diagnostic behavior • In the Operating mode parameter, the Switch option is selected. • In the Switch output function parameter, the Diagnostic behavior option is selected. The output is switched on (closed, conductive), if there is a pending diagnostic event of the assigned behavioral category. • Alarm • Alarm or warning • Warning – Assign limit • The Switch option is selected in Operating mode parameter. • The Limit option is selected in Switch output function parameter. Select the variable to monitor in case the specified limit value is exceeded. If a limit value is exceeded, the output is switched on (conductive). • Off • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Electronics temperature • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * • Totalizer 1 • Totalizer 2 • Totalizer 3 – Endress+Hauser 95 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Assign flow direction check • The Switch option is selected in the Operating mode parameter. • The Flow direction check option is selected in the Switch output function parameter. Select process variable for flow direction monitoring. – Assign status • The Switch option is selected in Operating mode parameter. • The Status option is selected in Switch output function parameter. Select the device function for • Off which to report the status. If • Low flow cut off the function is triggered, the output is closed and conductive (standard configuration). – Switch-on value • The Switch option is selected in the Operating mode parameter. • The Limit option is selected in the Switch output function parameter. Enter limit value for switch-on point (process variable > switch-on value = closed, conductive). Signed floating-point number Depends on country Switch-off value • The Switch option is selected in the Operating mode parameter. • The Limit option is selected in the Switch output function parameter. Enter limit value for switch-off Signed floating-point point (process variable < number switch-off value = open, nonconductive). Depends on country Switch-on delay • The Switch option is selected in the Operating mode parameter. • The Limit option is selected in the Switch output function parameter. Enter a delay before the output 0.0 to 100.0 s is switched on. – Switch-off delay • The Switch option is selected in the Operating mode parameter. • The Limit option is selected in the Switch output function parameter. Enter a delay before the output 0.0 to 100.0 s is switched off. – Failure mode – Select output behavior in the event of a device alarm. • Actual status • Open • Closed – Invert output signal – Invert the output signal. • No • Yes – * Selection / User entry Factory setting Visibility depends on order options or device settings 10.4.7 Configuring the relay output The Relay output wizard guides the user systematically through all the parameters that have to be set for configuring the relay output. Navigation "Setup" menu → Relay output 1 to n ‣ Relay output 1 to n Terminal number 96 → 97 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Relay output function → 97 Assign flow direction check → 97 Assign limit → 98 Assign diagnostic behavior → 98 Assign status → 98 Switch-off value → 98 Switch-off delay → 98 Switch-on value → 98 Switch-on delay → 98 Failure mode → 98 Switch state → 98 Powerless relay status → 98 Parameter overview with brief description Parameter Prerequisite Terminal number – Switch output function – Assign flow direction check The Flow direction check option is selected in the Relay output function parameter. Endress+Hauser Description Shows the terminal numbers used by the relay output module. User interface / Selection / User entry • Not used • 26-27 (I/O 1) • 24-25 (I/O 2) • 22-23 (I/O 3) • 20-21 (I/O 4) • Close • Open • Batching Select process variable for flow direction monitoring. 97 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description User interface / Selection / User entry Assign limit The Limit option is selected in Relay output function parameter. Select process variable for limit function. • Mass flow • Volume flow • Corrected volume flow • Target mass flow • Carrier mass flow • Density • Reference density • Dynamic viscosity • Concentration • Kinematic viscosity • Temp. compensated dynamic viscosity • Temp. compensated kinematic viscosity • Temperature • Totalizer 1 • Totalizer 2 • Totalizer 3 • Oscillation damping Assign diagnostic behavior In the Relay output function parameter, the Diagnostic behavior option is selected. Select diagnostic behavior for switch output. • Alarm • Alarm or warning • Warning Assign status In the Relay output function Select device status for switch output. parameter, the Digital Output option is selected. • Partially filled pipe detection • Low flow cut off Switch-off value The Limit option is selected in the Relay output function parameter. Enter measured value for the switch-off Signed floating-point point. number Switch-off delay In the Relay output function parameter, the Limit option is selected. Define delay for the switch-off of status 0.0 to 100.0 s output. Switch-on value The Limit option is selected in the Relay output function parameter. Enter measured value for the switch-on Signed floating-point point. number Switch-on delay In the Relay output function parameter, the Limit option is selected. Define delay for the switch-on of status output. 0.0 to 100.0 s Failure mode – Select output behavior in the event of a device alarm. • Actual status • Open • Closed Switch state – Select status of switch output. • Closed • Open Powerless relay status – • Open • Closed 10.4.8 Configuring the double pulse output The Double pulse output submenu guides the user systematically through all the parameters that have to be set for configuring the double pulse output. Navigation "Setup" menu → Double pulse output ‣ Double pulse output 98 Signal mode → 99 Master terminal number → 99 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Assign pulse output → 99 Measuring mode → 99 Value per pulse → 99 Pulse width → 99 Failure mode → 99 Invert output signal → 99 Parameter overview with brief description Parameter Description Selection / User interface / User entry Factory setting Signal mode Select the signal mode for the double pulse output. • Passive • Active • Passive NAMUR – Master terminal number Shows the terminal numbers used by the master of the double pulse output module. • Not used • 26-27 (I/O 1) • 24-25 (I/O 2) • 22-23 (I/O 3) • 20-21 (I/O 4) – Assign pulse output 1 Select process variable for pulse output. • Off • Mass flow • Volume flow • Corrected volume flow • Target mass flow • Carrier mass flow – Measuring mode Select measuring mode for pulse output. • Forward flow • Forward/Reverse flow • Reverse flow • Reverse flow compensation – Value per pulse Enter measured value at which a pulse is output. Signed floating-point number Depends on country and nominal diameter Pulse width Define time width of the output pulse. 0.5 to 2 000 ms – Failure mode Select output behavior in the event of a device alarm. • Actual value • No pulses – Invert output signal Invert the output signal. • No • Yes – 10.4.9 Configuring the local display The Display wizard guides you systematically through all the parameters that can configured for configuring the local display. Navigation "Setup" menu → Display ‣ Display Format display Endress+Hauser → 100 99 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Value 1 display → 100 0% bargraph value 1 → 100 100% bargraph value 1 → 100 Value 2 display → 100 Value 3 display → 101 0% bargraph value 3 → 101 100% bargraph value 3 → 101 Value 4 display → 101 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Format display A local display is provided. Select how measured values are shown on the display. • 1 value, max. size • 1 bargraph + 1 value • 2 values • 1 value large + 2 values • 4 values 1 value, max. size Value 1 display A local display is provided. Select the measured value that is shown on the local display. • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Electronics temperature • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * • Totalizer 1 • Totalizer 2 • Totalizer 3 Volume flow 0% bargraph value 1 A local display is provided. Enter 0 % value for bar graph display. Signed floating-point number Country-specific 100% bargraph value 1 A local display is provided. Enter 100 % value for bar graph display. Signed floating-point number Depends on country and nominal diameter Value 2 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) For the picklist, see Value 1 display parameter (→ 100) – 100 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Parameter Commissioning Prerequisite Description Selection / User entry Factory setting Value 3 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – 0% bargraph value 3 A selection was made in the Value 3 display parameter. Enter 0 % value for bar graph display. Signed floating-point number Country-specific 100% bargraph value 3 A selection was made in the Value 3 display parameter. Enter 100 % value for bar graph display. Signed floating-point number – Value 4 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – Value 5 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – Value 6 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – Value 7 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – Value 8 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – * Visibility depends on order options or device settings 10.4.10 Configuring the low flow cut off The Low flow cut off wizard systematically guides the user through all the parameters that must be set to configure low flow cut off. Structure of the wizard Assign variable Off Volume flow Mass flow Flow velocity On value Off value End of wizard A0043342-EN 21 Endress+Hauser "Low flow cutoff" wizard in the "Setup" menu 101 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Navigation "Setup" menu → Low flow cut off ‣ Low flow cut off Assign process variable (1837) → 102 On value low flow cutoff (1805) → 102 Off value low flow cutoff (1804) → 102 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Assign process variable – Select process variable for low flow cut off. • Off • Volume flow • Mass flow • Flow velocity Flow velocity On value low flow cutoff A process variable is selected Enter on value for low flow cut in the Assign process variable off. parameter (→ 102). Positive floatingpoint number 0.3 m/s Off value low flow cutoff A process variable is selected Enter off value for low flow cut 0 to 100.0 % in the Assign process variable off. parameter (→ 102). 102 – Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 10.5 Commissioning Advanced settings The Advanced setup submenu with its submenus contains parameters for specific settings. Navigation to the "Advanced setup" submenu XXXXXXXXX 20.50 mA 1. 0104-1 Main menu Display language English Display/operat. Setup Main menu Display/operat. Setup 2. Diagnostic / ../Setup Medium selection 3. XXXXXXXXX XXXXXXXXX / ../Setup XXXXXXXXX XXXXXXXXX Advanced setup 4. / ../Advanced setup Ent. access code 5. Device tag Def. access code 0092-1 **** A0032223-EN The number of submenus and parameters can vary depending on the device version. Certain submenus and parameters in these submenus are not described in the Operating Instructions. Instead a description is provided in the Special Documentation for the device ("Supplementary documentation"→ 168). Navigation "Setup" menu → Advanced setup ‣ Advanced setup Endress+Hauser Enter access code → 104 ‣ Sensor adjustment → 104 ‣ Totalizer 1 to n → 104 ‣ Display → 106 103 Commissioning Proline Prosonic Flow I 400 Modbus RS485 10.5.1 ‣ WLAN settings → 108 ‣ Heartbeat setup → 110 ‣ Administration → 111 Using the parameter to enter the access code Navigation "Setup" menu → Advanced setup Parameter overview with brief description Parameter Enter access code Description Enter access code to disable write protection of parameters. 10.5.2 User entry Max. 16-digit character string comprising numbers, letters and special characters Carrying out a sensor adjustment The Sensor adjustment submenu contains parameters that pertain to the functionality of the sensor. Navigation "Setup" menu → Advanced setup → Sensor adjustment ‣ Sensor adjustment → 104 Installation direction Parameter overview with brief description Parameter Installation direction Description Select sign of flow direction. 10.5.3 Selection • Forward flow • Reverse flow Configuring the totalizer In the "Totalizer 1 to n" submenu, you can configure the specific totalizer. Navigation "Setup" menu → Advanced setup → Totalizer 1 to n ‣ Totalizer 1 to n 104 Assign process variable 1 to n → 105 Process variable unit 1 to n → 105 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Totalizer 1 to n operation mode → 105 Totalizer 1 to n failure behavior → 105 Parameter overview with brief description Parameter Prerequisite Assign process variable 1 to n – Process variable unit 1 to n Description Factory setting • Off • Volume flow • Mass flow Volume flow A process variable is selected Select the unit for the process in the Assign process variable variable of the totalizer. parameter (→ 105) of the Totalizer 1 to n submenu. • g* • kg * • t* • oz * • lb * • STon * • cm³ * • dm³ * • m³ * • ml * • l* • hl * • Ml Mega * • af * • ft³ * • Mft³ * • Mft³ * • fl oz (us) * • gal (us) * • kgal (us) * • Mgal (us) * • bbl (us;liq.) * • bbl (us;beer) * • bbl (us;oil) * • bbl (us;tank) * • gal (imp) * • Mgal (imp) * • bbl (imp;beer) * • bbl (imp;oil) * • None * Depends on country: • m³ • ft³ Totalizer 1 to n operation mode A process variable is selected in the Assign process variable parameter (→ 105) of the Totalizer 1 to n submenu. • Net • Forward • Reverse Net flow total Totalizer 1 to n failure behavior A process variable is selected Select totalizer behavior in the in the Assign process variable event of a device alarm. parameter (→ 105) of the Totalizer 1 to n submenu. • Hold • Continue • Last valid value + continue Stop * Select process variable for totalizer. Selection Select totalizer operation mode, e.g. only totalize forward flow or only totalize reverse flow. Visibility depends on order options or device settings Endress+Hauser 105 Commissioning Proline Prosonic Flow I 400 Modbus RS485 10.5.4 Carrying out additional display configurations In the Display submenu you can set all the parameters associated with the configuration of the local display. Navigation "Setup" menu → Advanced setup → Display ‣ Display 106 Format display → 107 Value 1 display → 107 0% bargraph value 1 → 107 100% bargraph value 1 → 107 Decimal places 1 → 107 Value 2 display → 107 Decimal places 2 → 107 Value 3 display → 107 0% bargraph value 3 → 107 100% bargraph value 3 → 107 Decimal places 3 → 107 Value 4 display → 108 Decimal places 4 → 108 Display language → 108 Display interval → 108 Display damping → 108 Header → 108 Header text → 108 Separator → 108 Backlight → 108 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Factory setting Format display A local display is provided. Select how measured values are shown on the display. • 1 value, max. size • 1 bargraph + 1 value • 2 values • 1 value large + 2 values • 4 values 1 value, max. size Value 1 display A local display is provided. Select the measured value that is shown on the local display. • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Electronics temperature • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * • Totalizer 1 • Totalizer 2 • Totalizer 3 Volume flow 0% bargraph value 1 A local display is provided. Enter 0 % value for bar graph display. Signed floating-point number Country-specific 100% bargraph value 1 A local display is provided. Enter 100 % value for bar graph display. Signed floating-point number Depends on country and nominal diameter Decimal places 1 A measured value is specified in the Value 1 display parameter. Select the number of decimal places for the display value. • x • x.x • x.xx • x.xxx • x.xxxx x.xx Value 2 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) For the picklist, see Value 1 display parameter (→ 100) – Decimal places 2 A measured value is specified in the Value 2 display parameter. Select the number of decimal places for the display value. • x • x.x • x.xx • x.xxx • x.xxxx – Value 3 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – 0% bargraph value 3 A selection was made in the Value 3 display parameter. Enter 0 % value for bar graph display. Signed floating-point number Country-specific 100% bargraph value 3 A selection was made in the Value 3 display parameter. Enter 100 % value for bar graph display. Signed floating-point number – Decimal places 3 A measured value is specified in the Value 3 display parameter. Select the number of decimal places for the display value. • x • x.x • x.xx • x.xxx • x.xxxx – Endress+Hauser 107 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry Factory setting Value 4 display A local display is provided. Select the measured value that is shown on the local display. For the picklist, see Value 1 display parameter (→ 100) – Decimal places 4 A measured value is specified in the Value 4 display parameter. Select the number of decimal places for the display value. • x • x.x • x.xx • x.xxx • x.xxxx – Display language A local display is provided. Set display language. • English • Deutsch • Français • Español • Italiano • Nederlands • Portuguesa • Polski • русский язык (Russian) • Svenska • Türkçe • 中文 (Chinese) • 日本語 (Japanese) • 한국어 (Korean) • čeština (Czech) English (alternatively, the ordered language is preset in the device) Display interval A local display is provided. Set time measured values are shown on display if display alternates between values. 1 to 10 s – Display damping A local display is provided. Set display reaction time to fluctuations in the measured value. 0.0 to 999.9 s – Header A local display is provided. Select header contents on local • Device tag display. • Free text – Header text The Free text option is selected in the Header parameter. Enter display header text. Max. 12 characters, such as letters, numbers or special characters (e.g. @, %, /) – Separator A local display is provided. Select decimal separator for displaying numerical values. • . (point) • , (comma) . (point) Backlight A local display is provided. Switch the local display backlight on and off. • Disable • Enable – * Visibility depends on order options or device settings 10.5.5 WLAN configuration The WLAN Settings submenu guides the user systematically through all the parameters that have to be set for the WLAN configuration. Navigation "Setup" menu → Advanced setup → WLAN settings ‣ WLAN settings WLAN 108 → 109 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning WLAN mode → 109 SSID name → 109 Network security → 109 Security identification → 109 User name → 109 WLAN password → 109 WLAN IP address → 109 WLAN MAC address → 110 WLAN passphrase → 110 Assign SSID name → 110 SSID name → 110 Connection state → 110 Received signal strength → 110 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry / User interface Factory setting WLAN – Switch WLAN on and off. • Disable • Enable – WLAN mode – Select WLAN mode. WLAN access point – SSID name The client is activated. Enter the user-defined SSID name (max. 32 characters). – – Network security – Select the security type of the WLAN network. • Unsecured • WPA2-PSK • EAP-PEAP with MSCHAPv2 * • EAP-PEAP MSCHAPv2 no server authentic. * • EAP-TLS * – Security identification – Select security settings and download these settings via menu Data management > Security > WLAN. • Trusted issuer certificate • Device certificate • Device private key – User name – Enter user name. – – WLAN password – Enter WLAN password. – – WLAN IP address – Enter IP address of the WLAN interface of the device. 4 octet: 0 to 255 (in the particular octet) – Endress+Hauser 109 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry / User interface Factory setting Unique 12-digit character string comprising letters and numbers Each measuring device is given an individual address. WLAN MAC address – Enter MAC address of the WLAN interface of the device. WLAN passphrase The WPA2-PSK option is selected in the Security type parameter. Enter the network key (8 to 32 8 to 32-digit characters). character string comprising numbers, The network key supplied with the device letters and special characters (without should be changed spaces) during commissioning Serial number of the measuring device (e.g. L100A802000) for security reasons. Assign SSID name – Select which name will be used • Device tag for SSID: device tag or user• User-defined defined name. – SSID name • The User-defined option is selected in the Assign SSID name parameter. • The WLAN access point option is selected in the WLAN mode parameter. Enter the user-defined SSID name (max. 32 characters). EH_device designation_last 7 digits of the serial number (e.g. EH_Prosonic_Flow_4 00_A802000) Connection state – Displays the connection status. • Connected • Not connected – Received signal strength – Shows the received signal strength. • Low • Medium • High – Apply changes – Use changed WLAN settings. • Cancel • Ok – * Max. 32-digit character string comprising numbers, The user-defined SSID letters and special name may only be assigned once. If the SSID characters name is assigned more than once, the devices can interfere with one another. Visibility depends on order options or device settings 10.5.6 Performing Heartbeat basic setup Heartbeat setup submenu guides the user systematically through all the parameters that can be used for the Heartbeat basic setup. The wizard only appears if the device has the Heartbeat Verification +Monitoring application package. Navigation "Setup" menu → Advanced setup → Heartbeat setup ‣ Heartbeat setup ‣ Heartbeat base settings 110 → 111 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning "Heartbeat base settings" submenu Navigation "Setup" menu → Advanced setup → Heartbeat setup → Heartbeat base settings ‣ Heartbeat base settings Plant operator → 111 Location → 111 Parameter overview with brief description Parameter Description User entry Plant operator Enter the plant operator. Max. 32 characters such as letters, numbers or special characters (e.g. @, %, /) Location Enter the location. Max. 32 characters such as letters, numbers or special characters (e.g. @, %, /) 10.5.7 Using parameters for device administration The Administration submenu systematically guides the user through all the parameters that can be used for device administration purposes. Navigation "Setup" menu → Advanced setup → Administration ‣ Administration ‣ Define access code → 111 ‣ Reset access code → 112 Device reset → 112 Using the parameter to define the access code Complete this wizard to specify an access code for the Maintenance role. Navigation "Setup" menu → Advanced setup → Administration → Define access code ‣ Define access code Endress+Hauser Define access code → 112 Confirm access code → 112 111 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter overview with brief description Parameter Description User entry Define access code Specify an access code that is required to obtain the access rights for the Maintenance role. Max. 16-digit character string comprising numbers, letters and special characters Confirm access code Confirm the access code entered for the Maintenance role. Max. 16-digit character string comprising numbers, letters and special characters Using the parameter to reset the access code Navigation "Setup" menu → Advanced setup → Administration → Reset access code ‣ Reset access code Operating time → 112 Reset access code → 112 Parameter overview with brief description Parameter Description User interface / User entry Operating time Indicates how long the device has been in operation. Days (d), hours (h), minutes (m) and seconds (s) Reset access code Enter the code provided by Endress+Hauser Technical Support to reset the Maintenance code. Character string comprising numbers, letters and special characters a reset code, contact your Endress+Hauser service For organization. The reset code can only be entered via: • Web browser • DeviceCare, FieldCare (via CDI-RJ45 service interface) • Fieldbus Using the parameter to reset the device Navigation "Setup" menu → Advanced setup → Administration Parameter overview with brief description Parameter Device reset * Description Reset the device configuration - either entirely or in part - to a defined state. Selection • Cancel • To delivery settings • Restart device • Restore S-DAT backup * Visibility depends on order options or device settings 10.6 Simulation Via the Simulation submenu, it is possible to simulate various process variables in the process and the device alarm mode and verify downstream signal chains (switching valves 112 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning or closed-control loops). The simulation can be performed without a real measurement (no flow of medium through the device). The parameters displayed depend on: • The selected device order • The set operating mode of the pulse/frequency/switch outputs Navigation "Diagnostics" menu → Simulation ‣ Simulation Assign simulation process variable → 113 Process variable value → 113 Current output 1 simulation → 114 Current output value → 114 Frequency output 1 to n simulation → 114 Frequency output 1 to n value → 114 Pulse output simulation 1 to n → 114 Pulse value 1 to n → 114 Switch output simulation 1 to n → 114 Switch state 1 to n → 114 Device alarm simulation → 114 Diagnostic event category → 114 Diagnostic event simulation → 114 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry Assign simulation process variable – Select a process variable for the simulation process that is activated. • Off • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density Process variable value A process variable is selected in the Assign simulation process variable parameter (→ 113). Enter the simulation value for the selected process variable. Depends on the process variable selected Endress+Hauser 113 Commissioning Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Description Selection / User entry Simulation status input For the following order code: "Output; input", option I "4-20mA HART, 2x pul./freq./switch output; status input" • Off • On Value status input In the Simulation status input parameter, the On option is selected. • High • Low Current output 1 simulation – Switch the simulation of the current output on and off. • Off • On Current output value In the Current output simulation parameter, the On option is selected. Enter the current value for simulation. 3.59 to 22.5 mA Frequency output 1 to n simulation In the Operating mode parameter, the Frequency option is selected. Switch the simulation of the frequency output on and off. • Off • On Frequency output 1 to n value In the Frequency simulation 1 to n parameter, the On option is selected. Enter the frequency value for the simulation. 0.0 to 12 500.0 Hz Pulse output simulation 1 to n In the Operating mode parameter, the Pulse option is selected. Set and switch off the pulse output simulation. • Off • Fixed value • Down-counting value Fixed value option: Pulse For width parameter (→ 92) defines the pulse width of the pulses output. Pulse value 1 to n In the Pulse output simulation 1 to n parameter, the Down-counting value option is selected. Enter the number of pulses for simulation. 0 to 65 535 Switch output simulation 1 to n In the Operating mode parameter, the Switch option is selected. Switch the simulation of the switch output on and off. • Off • On Switch state 1 to n – Select the status of the status output for • Open the simulation. • Closed Device alarm simulation – Switch the device alarm on and off. • Off • On Diagnostic event category – Select a diagnostic event category. • Sensor • Electronics • Configuration • Process Diagnostic event simulation – Select a diagnostic event to simulate this event. • Off • Diagnostic event picklist (depends on the category selected) 10.7 Protecting settings from unauthorized access The following options exist for protecting the configuration of the measuring device from unintentional modification after commissioning: • Write protection via access code for the local display and Web browser • Write protection via write protection switch • Write protection via keypad lock 10.7.1 Write protection via access code The effects of the user-specific access code are as follows: • Via local operation, the parameters for the measuring device configuration are writeprotected and their values can no longer be changed. • Device access is protected via the Web browser, as are the parameters for the measuring device configuration. 114 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Commissioning Defining the access code via the local display 1. Navigate to the Define access code parameter (→ 112). 2. Maximum of 16-digit character string comprising numbers, letters and special characters as the access code. 3. Enter the access code again in the Confirm access code parameter (→ 112) to confirm. The symbol appears in front of all write-protected parameters. • Disabling parameter write protection via access code → 55. • If the access code is lost: Resetting the access code . • The user role with which the user is currently logged in is displayed in Access status display parameter. • Navigation path: Operation → Access status display • User roles and their access rights → 55 • The device automatically locks the write-protected parameters again if a key is not pressed for 10 minutes in the navigation and editing view. • The device locks the write-protected parameters automatically after 60 s if the user skips back to the operational display mode from the navigation and editing view. Parameters which can always be modified via the local display Certain parameters that do not affect the measurement are excepted from parameter write protection via the local display. Despite the user-specific access code, they can always be modified, even if the other parameters are locked. Parameters for configuring the language Parameters for configuring the local display Parameters for configuring the totalizer ↓ ↓ ↓ Display language Format display Control Totalizer Contrast display Preset value Display interval Reset all totalizers Defining the access code via the web browser 1. Navigate to the Define access code parameter (→ 112). 2. Define a 16-digit (max.) numeric code as the access code. 3. Enter the access code again in the Confirm access code parameter (→ 112) to confirm. The web browser switches to the login page. • Disabling parameter write protection via access code → 55. • If the access code is lost: Resetting the access code . • The Access status tooling parameter shows which user role the user is currently logged in with. • Navigation path: Operation → Access status tooling • User roles and their access rights → 55 If no action is performed for 10 minutes, the web browser automatically returns to the login page. Endress+Hauser 115 Commissioning Proline Prosonic Flow I 400 Modbus RS485 10.7.2 Write protection via write protection switch Unlike parameter write protection via a user-specific access code, this allows the user to lock write access to the entire operating menu - apart from the "Contrast display" parameter. The parameter values are now read only and cannot be edited any more (exception "Contrast display" parameter): • Via local display • Via MODBUS RS485 protocol 1. Loosen the 4 fixing screws on the housing cover and open the housing cover. 2. Setting the write protection switch (WP) on the main electronics module to the ON position enables the hardware write protection. Setting the write protection switch (WP) on the main electronics module to the OFF position (factory setting) disables the hardware write protection. If the hardware write protection is enabled: In Locking status parameter, the Hardware locked option is displayed. In addition, the symbol appears on the local display in front of the parameters in the header of the operational display and in the navigation view. XXXXXXXXX 20.50 XX XX A0029425 If hardware write protection is disabled: No option is displayed in the Locking status parameter . In the local display, the symbol disappears from in front of the parameters in the header of the operational display and in the navigation view. 3. LWARNING Excessive tightening torque applied to the fixing screws! Risk of damaging the plastic transmitter. ‣ Tighten the fixing screws as per the tightening torque → 39. Reassemble the transmitter in the reverse order. 116 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation 11 Operation 11.1 Reading off the device locking status Device active write protection: Locking status parameter Operation → Locking status Function scope of the "Locking status" parameter Options Description None The access authorization displayed in the Access status display parameter applies → 55. Only appears on local display. Hardware locked The DIP switch for hardware locking is activated on the main electronics module. This locks write access to the parameters (e.g. via local display or operating tool) → 116. Temporarily locked Write access to the parameters is temporarily locked on account of internal processes running in the device (e.g. data upload/download, reset, etc.). Once the internal processing has been completed, the parameters can be changed once again. 11.2 Adjusting the operating language Detailed information: • To configure the operating language → 74 • For information on the operating languages supported by the measuring device → 163 11.3 Configuring the display Detailed information: • On the basic settings for the local display → 99 • On the advanced settings for the local display → 106 11.4 Reading off measured values With the Measured values submenu, it is possible to read all the measured values. Navigation "Diagnostics" menu → Measured values ‣ Measured values Endress+Hauser ‣ Process variables → 118 ‣ System values → 119 ‣ Totalizer → 121 ‣ Output values → 120 117 Operation Proline Prosonic Flow I 400 Modbus RS485 11.4.1 Process variables The Process variables submenu contains all the parameters needed to display the current measured values for each process variable. Navigation "Diagnostics" menu → Measured values → Process variables ‣ Process variables Volume flow → 118 Mass flow → 118 Sound velocity → 118 Density → 118 Flow velocity → 119 Temperature → 119 Parameter overview with brief description Parameter Volume flow Prerequisite – Description Displays the volume flow that is currently measured. User interface Signed floating-point number Dependency The unit is taken from: Volume flow unit parameter (→ 81) Mass flow – Displays the mass flow that is currently calculated. Signed floating-point number Dependency The unit is taken from the Mass flow unit parameter (→ 82). Sound velocity – Displays the sound velocity that is currently measured. Signed floating-point number Dependency The unit is taken from the Velocity unit parameter. Density A fixed density is not entered. Displays the density that is currently calculated. Signed floating-point number Dependency The unit is taken from: Density unit parameter 118 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Parameter Flow velocity Operation Prerequisite – Description Displays the average flow velocity that is currently calculated. User interface Signed floating-point number Dependency The unit is taken from: Velocity unit parameter Temperature Temperature is not entered as a fixed value. Displays the temperature that is currently measured. Signed floating-point number Dependency The unit is taken from: Temperature unit parameter 11.4.2 System values The System values submenu contains all the parameters needed to display the current measured values for every system value. Navigation "Diagnostics" menu → Measured values → System values ‣ System values Signal strength → 119 Acceptance rate → 119 Signal to noise ratio → 119 Turbulence → 119 Parameter overview with brief description Parameter Signal strength Description Displays the current signal strength (0 to 100 dB). User interface Signed floating-point number Assessment of the signal strength: • < 10 dB: bad • > 90 dB: very good Acceptance rate Displays the ratio of the number of ultrasonic signals accepted for flow calculation and the total number of ultrasonic signals emitted. 0 to 100 % Signal to noise ratio Displays the current signal to noise ratio (0 to 100 dB). Signed floating-point number Assessment of the signal-to-noise ratio: • < 20 dB: bad • > 50 dB: very good Turbulence Displays the current turbulence. 11.4.3 Signed floating-point number Input values The Input values submenu guides you systematically to the individual input values. The submenu only appears if the device was ordered with a status input → 35.. Endress+Hauser 119 Operation Proline Prosonic Flow I 400 Modbus RS485 Navigation "Diagnostics" menu → Measured values → Input values ‣ Input values → 120 Value status input Parameter overview with brief description Parameter Value status input Prerequisite Description For the following order code: "Output; input", option I "4-20mA HART, 2x pul./freq./switch output; status input" 11.4.4 User interface • High • Low Output values The Output values submenu contains all the parameters needed to display the current measured values for every output. The parameters displayed depend on: • The selected device order • The set operating mode of the pulse/frequency/switch outputs Navigation "Diagnostics" menu → Measured values → Output values ‣ Output values 120 Output current → 121 Measured current → 121 Pulse output → 121 Output frequency → 121 Switch state → 121 Output frequency → 121 Pulse output → 121 Switch state → 121 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation Parameter overview with brief description Parameter Prerequisite Description User interface Output current – Displays the current value currently calculated for the current output. 3.59 to 22.5 mA Measured current – Displays the current value currently measured for the current output. 0 to 30 mA Pulse output 1 to n The Pulse option is selected in the Displays the pulse frequency currently Operating mode parameter parameter. output. Positive floating-point number Output frequency 1 to n In the Operating mode parameter, the Frequency option is selected. Displays the value currently measured for the frequency output. 0.0 to 12 500.0 Hz Switch state 1 to n In the Operating mode parameter, the Switch option is selected. Displays the current switch output status. • Open • Closed 11.4.5 "Totalizer" submenu The Totalizer submenu contains all the parameters needed to display the current measured values for every totalizer. Navigation "Diagnostics" menu → Measured values → Totalizer ‣ Totalizer Totalizer 1 to n value → 121 Totalizer 1 to n overflow → 121 Parameter overview with brief description Parameter Prerequisite Description Totalizer 1 to n value One of the following options is selected in the Assign process variable parameter (→ 105) of the Totalizer 1 to n submenu: • Volume flow • Mass flow Displays the current totalizer counter value. Signed floating-point number Totalizer 1 to n overflow One of the following options is selected in the Assign process variable parameter (→ 105) of the Totalizer 1 to n submenu: • Volume flow • Mass flow Displays the current totalizer overflow. Integer with sign 11.5 User interface Adapting the measuring device to the process conditions The following are available for this purpose: • Basic settings using theSetup menu (→ 74) • Advanced settings using theAdvanced setup submenu (→ 103) Endress+Hauser 121 Operation Proline Prosonic Flow I 400 Modbus RS485 11.6 Performing a totalizer reset The totalizers are reset in the Operation submenu: • Control Totalizer • Reset all totalizers Navigation "Operation" menu → Totalizer handling ‣ Totalizer handling Control Totalizer 1 to n → 122 Preset value 1 to n → 122 Totalizer value 1 to n → 122 Reset all totalizers → 122 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry / User interface Totalizer 1 to n control A process variable is selected Control totalizer value. in the Assign process variable parameter (→ 105) of the Totalizer 1 to n submenu. • Totalize • Reset + hold • Preset + hold • Reset + totalize • Preset + totalize • Hold Preset value 1 to n A process variable is selected Specify start value for totalizer. Signed floating-point in the Assign process variable Dependency number parameter (→ 105) of the The unit of the selected Totalizer 1 to n submenu. process variable is defined in the Unit totalizer parameter (→ 105) for the totalizer. Depends on country: • 0 m³ • 0 ft³ Totalizer value One of the following options is selected in the Assign process variable parameter (→ 105) of the Totalizer 1 to n submenu: • Volume flow • Mass flow Displays the current totalizer counter value. Signed floating-point number – Reset all totalizers – Reset all totalizers to 0 and start. • Cancel • Reset + totalize – 11.6.1 122 Factory setting – Function scope of "Control Totalizer" parameter Options Description Totalize The totalizer is started or continues running. Reset + hold The totaling process is stopped and the totalizer is reset to 0. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Operation Options Preset + hold Description 1) The totaling process is stopped and the totalizer is set to its defined start value from the Preset value parameter. Reset + totalize Preset + totalize 1) The totalizer is reset to 0 and the totaling process is restarted. 1) The totalizer is set to the defined start value in the Preset value parameter and the totaling process is restarted. Visible depending on the order options or device settings 11.6.2 Function range of "Reset all totalizers" parameter Options Description Cancel No action is executed and the user exits the parameter. Reset + totalize Resets all totalizers to 0 and restarts the totaling process. This deletes all the previously aggregated flow values. 11.7 Displaying the measured value history The Extended HistoROM application package must be enabled in the device (order option) for the Data logging submenu to appear. This contains all the parameters for the measured value history. Data logging is also available via: • Plant Asset Management Tool FieldCare → 65. • Web browser Function range • A total of 1000 measured values can be stored • 4 logging channels • Adjustable logging interval for data logging • Measured value trend for each logging channel displayed in the form of a chart / ../XXXXXXXX 175.77 40.69 l/h -100s 0 A0034352 • x-axis: depending on the number of channels selected displays 250 to 1000 measured values of a process variable. • y-axis: displays the approximate measured value span and constantly adapts this to the ongoing measurement. If the length of the logging interval or the assignment of the process variables to the channels is changed, the content of the data logging is deleted. Navigation "Diagnostics" menu → Data logging ‣ Data logging Assign channel 1 Endress+Hauser → 124 123 Operation Proline Prosonic Flow I 400 Modbus RS485 Assign channel 2 → 124 Assign channel 3 → 124 Assign channel 4 → 124 Logging interval → 125 Clear logging data → 125 Data logging → 125 Logging delay → 125 Data logging control → 125 Data logging status → 125 Entire logging duration → 125 Parameter overview with brief description Parameter Prerequisite Description Selection / User entry / User interface Assign channel 1 The Extended HistoROM application package is available. Assign process variable to logging channel. • Off • Volume flow • Mass flow • Flow velocity • Sound velocity • Temperature • Density • Signal strength * • Signal to noise ratio * • Acceptance rate * • Turbulence * • Electronics temperature • Current output 1 Assign channel 2 The Extended HistoROM application package is available. Assign a process variable to logging channel. For the picklist, see Assign channel 1 parameter (→ 124) Assign a process variable to logging channel. For the picklist, see Assign channel 1 parameter (→ 124) Assign a process variable to logging channel. For the picklist, see Assign channel 1 parameter (→ 124) software options currently The enabled are displayed in the Software option overview parameter. Assign channel 3 The Extended HistoROM application package is available. software options currently The enabled are displayed in the Software option overview parameter. Assign channel 4 The Extended HistoROM application package is available. software options currently The enabled are displayed in the Software option overview parameter. 124 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Parameter Prerequisite Operation Description Selection / User entry / User interface Logging interval The Extended HistoROM application package is available. Define the logging interval for data logging. This value defines the time interval between the individual data points in the memory. 0.1 to 3 600.0 s Clear logging data The Extended HistoROM application package is available. Clear the entire logging data. • Cancel • Clear data Data logging – Select the type of data logging. • Overwriting • Not overwriting Logging delay In the Data logging parameter, the Not Enter the time delay for measured overwriting option is selected. value logging. 0 to 999 h Data logging control In the Data logging parameter, the Not Start and stop measured value logging. overwriting option is selected. • None • Delete + start • Stop Data logging status In the Data logging parameter, the Not Displays the measured value logging overwriting option is selected. status. • Done • Delay active • Active • Stopped Entire logging duration In the Data logging parameter, the Not Displays the total logging duration. overwriting option is selected. Positive floating-point number * Visibility depends on order options or device settings Endress+Hauser 125 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 12 Diagnosis and troubleshooting 12.1 General troubleshooting For local display Error Possible causes Remedial action Local display dark and no output signals Supply voltage does not match the voltage specified on the nameplate. Apply the correct supply voltage → 39. Local display dark and no output signals No contact between connecting cables and terminals. Ensure electrical contact between the cable and the terminal. Local display dark and no output signals • • Terminals are not plugged into the main electronics module correctly. Check terminals. Local display dark and no output signals • • Main electronics module is defective. Order spare part → 146. Local display dark and no output signals The connector between the main electronics module and display module is not plugged in correctly. Check the connection and correct if necessary. Local display cannot be read, but signal output is Display is set too bright or too dark. within the valid range • Set the display brighter by simultaneously pressing + . • Set the display darker by simultaneously pressing + . Local display is dark, but signal output is within the valid range Display module is defective. Order spare part → 146. Backlighting of local display is red Diagnostic event with "Alarm" diagnostic behavior has occurred. Take remedial measures → 135 Text on local display appears in a language that cannot be understood. The selected operating language cannot be understood. 1. Press + for 2 s ("home position"). 2. Press . 3. Configure the required language in the Display language parameter (→ 108). Message on local display: "Communication Error" "Check Electronics" Communication between the display module and • Check the cable and the connector between the electronics is interrupted. the main electronics module and display module. • Order spare part → 146. For output signals Error Possible causes Remedial action Signal output outside the valid range Main electronics module is defective. Order spare part → 146. Device shows correct value on local display, but signal output is incorrect, though in the valid range. Parameter configuration error Check and adjust parameter configuration. Device measures incorrectly. Configuration error or device is operated outside the application. 1. Check and correct parameter configuration. 2. Observe limit values specified in the "Technical Data". Possible causes Remedial action For access Error Write access to parameter not possible. Hardware write protection is enabled. Set the write protection switch on the main electronics module to the OFF position → 116. Write access to parameter not possible. Current user role has limited access authorization. 1. Check user role → 55. 2. Enter correct customer-specific access code → 55. 126 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Error Diagnosis and troubleshooting Possible causes Remedial action Connection via Modbus RS485 is not possible. Modbus RS485 bus cable is connected incorrectly. Check the terminal assignment . Connection via Modbus RS485 is not possible. Modbus RS485 cable is incorrectly terminated. Check the terminating resistor → 40. Connection via Modbus RS485 is not possible. Settings for the communication interface are incorrect. Check the Modbus RS485 configuration → 82. Connection to the web server is not possible. Web server is disabled. Use the "FieldCare" or "DeviceCare" operating tool to check if the web server of the device is enabled and enable if necessary → 62. The Ethernet interface is incorrectly configured on the PC. ‣ Check the properties of the Internet protocol (TCP/IP) → 58. ‣ Check the network settings with the IT manager. Connection to the web server is not possible. The IP address is incorrectly configured on the PC. Check the IP address: 192.168.1.212 → 58 Web browser is frozen and no further operation possible. Data transfer is active. Wait until data transfer or current action is finished. Connection lost ‣ Check cable connection and power supply. ‣ Refresh web browser and restart if necessary. The web browser contents are difficult to read or The web browser version used is not the best incomplete. option. No contents displayed in the web browser or contents incomplete. ‣ Use correct web browser version → 57. ‣ Empty the web browser cache. ‣ Restart the web browser. Unsuitable view settings. Change the font size/display ratio of the Web browser. • JavaScript is not enabled. • JavaScript cannot be enabled. ‣ Enable JavaScript. ‣ Enter http://192.168.1.212/servlet/ basic.html as the as IP address. Operation with FieldCare or DeviceCare not possible via CDI-RJ45 service interface (port 8000). Firewall of the PC or network prevents communication. Depending on the settings of the firewall used on the PC or in the network, the firewall must be disabled or adjusted for FieldCare/DeviceCare access. Flashing of firmware with FieldCare or DeviceCare not possible via CDI-RJ45 service interface (port 8000 or TFTP ports). Firewall of the PC or network prevents communication. Depending on the settings of the firewall used on the PC or in the network, the firewall must be disabled or adjusted for FieldCare/DeviceCare access. 12.2 Diagnostic information via light emitting diodes 12.2.1 Transmitter Different LEDs in the transmitter provide information on the device status. Endress+Hauser 127 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 r Po I/O I/O I/O we 2 3 4 ES C + Po ES - E we r op en pres s C + - op en pres s 3. 2. I/O 3 I/O 2 P ow er 1. 5 I/O 3 1 2 3 4 A0029689 1 2 3 4 5 Supply voltage Device status Not used Communication Service interface (CDI) active 1. Open the housing cover. 2. Remove the display module. 3. Fold open the terminal cover. LED Supply voltage Alarm Device status Color Meaning Off Supply voltage is off or too low Green Supply voltage is ok Off Device status is ok Flashing red A device error of diagnostic behavior "Warning" has occurred Red • A device error of diagnostic behavior "Alarm" has occurred • Boot loader is active Green Device status is ok Flashing red A device error of diagnostic behavior "Warning" has occurred Red A device error of diagnostic behavior "Alarm" has occurred Alternately flashing red/green Boot loader is active 128 Communication Flashing white Modbus RS485 communication is active Alarm Green Measuring device is ok Flashing green Measuring device not configured Off Firmware error Red Main error Flashing red Fault Flashing red/green Start measuring device Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Diagnosis and troubleshooting 12.3 Diagnostic information on local display 12.3.1 Diagnostic message Faults detected by the self-monitoring system of the measuring device are displayed as a diagnostic message in alternation with the operational display. Operational display in alarm condition Diagnostic message 2 1 XXXXXXXXX S 20.50 S801 3 4 Supply voltage XX X S XXXXXXXXX i Menu 5 A0029426-EN 1 2 3 4 5 Status signal Diagnostic behavior Diagnostic behavior with diagnostic code Short text Operating elements If two or more diagnostic events are pending simultaneously, only the message of the diagnostic event with the highest priority is shown. Other diagnostic events that have occurred can be displayed in the Diagnostics menu: • Via parameter → 138 • Via submenus → 139 Status signals The status signals provide information on the state and reliability of the device by categorizing the cause of the diagnostic information (diagnostic event). The status signals are categorized according to VDI/VDE 2650 and NAMUR Recommendation NE 107: F = Failure, C = Function Check, S = Out of Specification, M = Maintenance Required Symbol Meaning Failure A device error has occurred. The measured value is no longer valid. Function check The device is in service mode (e.g. during a simulation). Out of specification The device is being operated: Outside its technical specification limits (e.g. outside the process temperature range) Maintenance required Maintenance is required. The measured value remains valid. Endress+Hauser 129 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 Diagnostic behavior Symbol Meaning Alarm • Measurement is interrupted. • Signal outputs and totalizers assume the defined alarm condition. • A diagnostic message is generated. • The background lighting changes to red. Warning • Measurement is resumed. • The signal outputs and totalizers are not affected. • A diagnostic message is generated. Diagnostic information The fault can be identified using the diagnostic information. The short text helps you by providing information about the fault. In addition, the corresponding symbol for the diagnostic behavior is displayed in front of the diagnostic information on the local display. Diagnostic information Diagnostic code Diagnostic behavior Status signal Diagnostic number Short text ↓ ↓ ↓ 842 Process limit Example A0013962 A0013958 NAMUR NE 107 3-digit number Operating elements Operating key Meaning Plus key In menu, submenu Opens the message about the remedial measures. Enter key In menu, submenu Opens the operating menu. 130 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 12.3.2 Diagnosis and troubleshooting Calling up remedial measures S XXXXXXXXX 20.50 S801 Supply voltage i XX X S XXXXXXXXX Menu 1. 1 Diagnostic list Diagnostics 1 S S801 Supply voltage Diagnostics 2 Diagnostics 3 2. 2 4 6 Supply voltage (ID:203) S801 0d00h02m25s Increase supply voltage 3 5 3. A0029431-EN 22 Message for remedial measures 1 2 3 4 5 6 Diagnostic information Short text Service ID Diagnostic behavior with diagnostic code Operation time when error occurred Remedial measures 1. The user is in the diagnostic message. Press ( symbol). The Diagnostic list submenu opens. 2. Select the desired diagnostic event with or and press . The message about the remedial measures opens. 3. Press + simultaneously. The message about the remedial measures closes. The user is in the Diagnostics menu at an entry for a diagnostics event, e.g. in the Diagnostic list submenu or Previous diagnostics parameter. 1. Press . The message for the remedial measures for the selected diagnostic event opens. 2. Press + simultaneously. The message for the remedial measures closes. 12.4 Diagnostic information in the web browser 12.4.1 Diagnostic options Any faults detected by the measuring device are displayed in the Web browser on the home page once the user has logged on. Endress+Hauser 131 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 1 2 3 A0031056 1 2 3 Status area with status signal Diagnostic information → 130 Remedial measures with service ID In addition, diagnostic events which have occurred can be shown in the Diagnostics menu: • Via parameter → 138 • Via submenu → 139 Status signals The status signals provide information on the state and reliability of the device by categorizing the cause of the diagnostic information (diagnostic event). Symbol Meaning Failure A device error has occurred. The measured value is no longer valid. Function check The device is in service mode (e.g. during a simulation). Out of specification The device is being operated: Outside its technical specification limits (e.g. outside the process temperature range) Maintenance required Maintenance is required. The measured value remains valid. The status signals are categorized in accordance with VDI/VDE 2650 and NAMUR Recommendation NE 107. 12.4.2 Calling up remedy information Remedy information is provided for every diagnostic event to ensure that problems can be rectified quickly. These measures are displayed in red along with the diagnostic event and the related diagnostic information. 12.5 Diagnostic information in FieldCare or DeviceCare 12.5.1 Diagnostic options Any faults detected by the measuring device are displayed on the home page of the operating tool once the connection has been established. 132 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Diagnosis and troubleshooting 1 Pro... Pro... 2 3 A0008199 1 2 3 Status area with status signal → 129 Diagnostic information → 130 Remedial measures with service ID In addition, diagnostic events which have occurred can be shown in the Diagnostics menu: • Via parameter → 138 • Via submenu → 139 Diagnostic information The fault can be identified using the diagnostic information. The short text helps you by providing information about the fault. In addition, the corresponding symbol for the diagnostic behavior is displayed in front of the diagnostic information on the local display. Diagnostic information Diagnostic code Diagnostic behavior Status signal Diagnostic number Short text ↓ ↓ ↓ 842 Process limit Example A0013962 A0013958 NAMUR NE 107 12.5.2 3-digit number Calling up remedy information Remedy information is provided for every diagnostic event to ensure that problems can be rectified quickly: • On the home page Remedy information is displayed in a separate field below the diagnostics information. • In the Diagnostics menu Remedy information can be called up in the working area of the user interface. The user is in the Diagnostics menu. Endress+Hauser 1. Call up the desired parameter. 2. On the right in the working area, mouse over the parameter. A tool tip with remedy information for the diagnostic event appears. 133 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 12.6 Diagnostic information via communication interface 12.6.1 Reading out diagnostic information Diagnostic information can be read out via Modbus RS485 register addresses. • Via register address 6821 (data type = string): diagnosis code, e.g. F270 • Via register address 6859 (data type = integer): diagnosis number, e.g. 270 For an overview of diagnostic events with diagnosis number and diagnosis code → 135 12.6.2 Configuring error response mode The error response mode for Modbus RS485 communication can be configured in the Communication submenu using 2 parameters. Navigation path Setup → Communication Parameter overview with brief description Parameter Failure mode Description Options Factory setting Select measured value • NaN value NaN value output behavior when a • Last valid value diagnostic message occurs NaN º not a number via Modbus communication. effect of this The parameter depends on the option selected in the Assign diagnostic behavior parameter. 12.7 Adapting the diagnostic information 12.7.1 Adapting the diagnostic behavior Each item of diagnostic information is assigned a specific diagnostic behavior at the factory. The user can change this assignment for specific diagnostic information in the Diagnostic behavior submenu. Expert → System → Diagnostic handling → Diagnostic behavior You can assign the following options to the diagnostic number as the diagnostic behavior: 134 Options Description Alarm The device stops measurement. The measured value output via Modbus RS485 and the totalizers assume the defined alarm condition. A diagnostic message is generated. The background lighting changes to red. Warning The device continues to measure. The measured value output via Modbus RS485 and the totalizers are not affected. A diagnostic message is generated. Logbook entry only The device continues to measure. The diagnostic message is only displayed in the Event logbook submenu (Event list submenu) and is not displayed in alternating sequence with the operational display. Off The diagnostic event is ignored, and no diagnostic message is generated or entered. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 12.8 Diagnosis and troubleshooting Overview of diagnostic information The amount of diagnostic information and the number of measured variables affected increase if the measuring device has one or more application packages. In the case of some items of diagnostic information, the diagnostic behavior can be changed. Adapting the diagnostic information → 134 Diagnostic number Short text Remedy instructions Status signal [from the factory] Diagnostic behavior [from the factory] Diagnostic of sensor 019 Device initialization active Device initialization in progress, please S wait Warning 1) 082 Data storage inconsistent Check module connections F Alarm 083 Memory content inconsistent 1. Restart device 2. Restore S-DAT data 3. Replace S-DAT F Alarm 104 Sensor signal path 1 to n 1. Check process conditions 2. Clean or replace transducers 3. Replace sensor electronic module (ISEM) F Alarm 105 Downstream transducer path 1 to n defective 1. Check connection to the downstream transducer 2. Replace downstream transducer F Alarm 106 Upstream transducer path 1 defective 1. Check connection to the upstream transducer 2. Replace upstream transducer F Alarm 160 Signal path switched off Contact service M Warning 1) Diagnostic of electronic Endress+Hauser 201 Electronics faulty 1. Restart device 2. Replace electronics F Alarm 242 Firmware incompatible 1. Check firmware version 2. Flash or replace electronic module F Alarm 252 Module incompatible 1. Check electronic modules 2. Check if correct modules are available (e.g. NEx, Ex) 3. Replace electronic modules F Alarm 262 Module connection interrupted 1. Check or replace connection cable between sensor electronic module (ISEM) and main electronics 2. Check or replace ISEM or main electronics F Alarm 270 Main electronics defective 1. Restart device 2. Replace main electronic module F Alarm 271 Main electronics faulty 1. Restart device 2. Replace main electronic module F Alarm 272 Main electronics faulty Restart device F Alarm 273 Main electronics defective 1. Pay attention to display emergency operation 2. Replace main electronics F Alarm 275 I/O module defective Change I/O module F Alarm 276 I/O module faulty 1. Restart device 2. Change I/O module F Alarm 135 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 Diagnostic number Short text Remedy instructions Status signal [from the factory] Diagnostic behavior [from the factory] 281 Electronic initialization active Firmware update active, please wait! F Alarm 283 Memory content inconsistent Restart device F Alarm 302 Device verification active Device verification active, please wait. C Warning 1) 311 Sensor electronics (ISEM) faulty Maintenance required! Do not reset device M Warning 361 I/O module 1 faulty 1. Restart device 2. Check electronic modules 3. Change I/O module or main electronics F Alarm 372 Sensor electronics (ISEM) faulty 1. Restart device 2. Check if failure recurs 3. Replace sensor electronic module (ISEM) F Alarm 373 Sensor electronics (ISEM) faulty Transfer data or reset device F Alarm 375 I/O- communication failed 1. Restart device 2. Check if failure recurs 3. Replace module rack inclusive electronic modules F Alarm 378 Supply voltage ISEM faulty 1. If available: Check connection cable between sensor and transmitter 2. Replace main electronic module 3. Replace sensor electronic module (ISEM) F Alarm 382 Data storage 1. Insert T-DAT 2. Replace T-DAT F Alarm 383 Memory content Reset device F Alarm 384 Transmitter circuit 1. Restart device 2. Check if failure recurs 3. Replace sensor electronic module (ISEM) F Alarm 385 Amplifier circuit 1. Restart device 2. Check if failure recurs 3. Replace sensor electronic module (ISEM) F Alarm 386 Time of flight 1. Restart device 2. Check if failure recurs 3. Replace sensor electronic module (ISEM) F Alarm 387 HistoROM data faulty Contact service organization F Alarm Diagnostic of configuration 136 410 Data transfer failed 1. Retry data transfer 2. Check connection F Alarm 412 Processing download Download active, please wait C Warning 431 Trim 1 required Carry out trim M Warning 437 Configuration incompatible 1. Update firmware 2. Execute factory reset F Alarm 438 Dataset different 1. Check dataset file 2. Check device parameterization 3. Download new device parameterization M Warning Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Diagnosis and troubleshooting Diagnostic number Short text Remedy instructions Status signal [from the factory] Diagnostic behavior [from the factory] 441 Current output 1 saturated 1. Check current output settings 2. Check process S Warning 1) 442 Frequency output 1 to n saturated 1. Check frequency output settings 2. Check process S Warning 1) 443 Pulse output 1 to n saturated 1. Check pulse output settings 2. Check process S Warning 1) 453 Flow override active Deactivate flow override C Warning 484 Failure mode simulation active Deactivate simulation C Alarm 485 Process variable simulation active Deactivate simulation C Warning 491 Current output 1 simulation active Deactivate simulation C Warning 492 Frequency output 1 to n simulation active Deactivate simulation frequency output C Warning 493 Pulse output simulation active Deactivate simulation pulse output C Warning 494 Switch output 1 to n simulation active Deactivate simulation switch output C Warning 495 Diagnostic event simulation active Deactivate simulation C Warning 537 Configuration 1. Check IP addresses in network 2. Change IP address F Warning Diagnostic of process Endress+Hauser 803 Loop current 1 faulty 1. Check wiring 2. Change I/O module F Alarm 832 Electronics temperature too high Reduce ambient temperature S Warning 1) 833 Electronics temperature too low Increase ambient temperature S Warning 1) 841 Flow velocity too high Reduce flow rate S Warning 1) 842 Process value below limit Low flow cut off active! Check low flow cut off configuration S Warning 1) 870 Measuring inaccuracy increased 1. Check process 2. Increase flow volume F Alarm 1) 881 Signal to noise ratio too low 1. Check process conditions F 2. Clean/repl. transd. (inline) / check sensor pos. and coupling (clamp on) 3. Replace sensor electronic module (ISEM) Alarm 882 Input signal faulty 1. Check input signal parameterization F 2. Check external device 3. Check process conditions Alarm 930 Sound velocity too high 1. Check process conditions S 2. Clean/repl. transd. (inline) / check sensor pos. and coupling (clamp on) 3. Replace sensor electronic module (ISEM) Warning 1) 137 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 1) Diagnostic number Short text Remedy instructions Status signal [from the factory] 931 Sound velocity too low 1. Check process conditions S 2. Clean/repl. transd. (inline) / check sensor pos. and coupling (clamp on) 3. Replace sensor electronic module (ISEM) Warning 1) 953 Asymmetry noise signal too high path 1 to n 1. Check process conditions 2. Clean or replace transducers 3. Replace sensor electronic module (ISEM) Alarm M Diagnostic behavior [from the factory] Diagnostic behavior can be changed. 12.9 Pending diagnostic events The Diagnostics menu allows the user to view the current diagnostic event and the previous diagnostic event separately. To call up the measures to rectify a diagnostic event: • Via local display → 131 • Via web browser → 132 • Via "FieldCare" operating tool → 133 • Via "DeviceCare" operating tool → 133 Other pending diagnostic events can be displayed in the Diagnostic list submenu → 139. Navigation "Diagnostics" menu Diagnostics 138 Actual diagnostics → 139 Previous diagnostics → 139 Operating time from restart → 139 Operating time → 139 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Diagnosis and troubleshooting Parameter overview with brief description Parameter Actual diagnostics Prerequisite A diagnostic event has occurred. Description User interface Shows the current occured diagnostic event along with its diagnostic information. Symbol for diagnostic behavior, diagnostic code and short message. two or more messages occur Ifsimultaneously, the message with the highest priority is shown on the display. Previous diagnostics Two diagnostic events have already occurred. Shows the diagnostic event that occurred prior to the current diagnostic event along with its diagnostic information. Symbol for diagnostic behavior, diagnostic code and short message. Operating time from restart – Shows the time the device has been in operation since the last device restart. Days (d), hours (h), minutes (m) and seconds (s) Operating time – Indicates how long the device has been in operation. Days (d), hours (h), minutes (m) and seconds (s) 12.10 Diagnostics list Up to 5 currently pending diagnostic events can be displayed in the Diagnostic list submenu along with the associated diagnostic information. If more than 5 diagnostic events are pending, the events with the highest priority are shown on the display. Navigation path Diagnostics → Diagnostic list / ../Diagnose list Diagnostics F273 Main electronic Diagnostics 2 Diagnostics 3 A0014006-EN 23 Using the example of the local display To call up the measures to rectify a diagnostic event: • Via local display → 131 • Via web browser → 132 • Via "FieldCare" operating tool → 133 • Via "DeviceCare" operating tool → 133 12.11 Event logbook 12.11.1 Reading out the event logbook A chronological overview of the event messages that have occurred is provided in the Events list submenu. Navigation path Diagnostics menu → Event logbook submenu → Events list Endress+Hauser 139 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 / ../Eventlist F I1091 Config. change I1157 Mem.err. ev.list 0d01h19m10s F311 Electr. failure A0014008-EN 24 Using the example of the local display • A maximum of 20 event messages can be displayed in chronological order. • If the Extended HistoROM application package (order option) is enabled in the device, the event list can contain up to 100 entries. The event history includes entries for: • Diagnostic events → 135 • Information events → 140 In addition to the operating time when the event occurred, each event is also assigned a symbol that indicates whether the event has occurred or is finished: • Diagnostics event • : Occurrence of the event • : End of the event • Information event : Occurrence of the event To call up the measures to rectify a diagnostic event: • Via local display → 131 • Via web browser → 132 • Via "FieldCare" operating tool → 133 • Via "DeviceCare" operating tool → 133 For filtering the displayed event messages → 140 12.11.2 Filtering the event logbook Using the Filter options parameter you can define which category of event message is displayed in the Events list submenu. Navigation path Diagnostics → Event logbook → Filter options Filter categories • All • Failure (F) • Function check (C) • Out of specification (S) • Maintenance required (M) • Information (I) 12.11.3 Overview of information events Unlike a diagnostic event, an information event is displayed in the event logbook only and not in the diagnostic list. Info number 140 Info name I1000 --------(Device ok) I1079 Sensor changed I1089 Power on I1090 Configuration reset I1091 Configuration changed Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Diagnosis and troubleshooting Info number Info name I1092 HistoROM backup deleted I1137 Electronics changed I1151 History reset I1155 Reset electronics temperature I1156 Memory error trend I1157 Memory error event list I1256 Display: access status changed I1278 I/O module restarted I1327 Zero point adjust failed signal path I1335 Firmware changed I1361 Web server: login failed I1397 Fieldbus: access status changed I1398 CDI: access status changed I1444 Device verification passed I1445 Device verification failed I1457 Measurement error verification failed I1459 I/O module verification failed I1461 Sensor verification failed I1462 Sensor electronic module verific. failed I1512 Download started I1513 Download finished I1514 Upload started I1515 Upload finished I1622 Calibration changed I1624 All totalizers reset I1625 Write protection activated I1626 Write protection deactivated I1627 Web server: login successful I1628 Display: login successful I1629 CDI: login successful I1631 Web server access changed I1632 Display: login failed I1633 CDI: login failed I1634 Reset to factory settings I1635 Reset to delivery settings I1649 Hardware write protection activated I1650 Hardware write protection deactivated I1725 Sensor electronic module (ISEM) changed 12.12 Resetting the measuring device The entire device configuration or some of the configuration can be reset to a defined state with the Device reset parameter (→ 112). Endress+Hauser 141 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 12.12.1 Function range of "Device reset" parameter Options Description Cancel No action is executed and the user exits the parameter. To delivery settings Every parameter for which a customer-specific default setting was ordered is reset to the customer-specific value. All other parameters are reset to the factory setting. Restart device The restart resets every parameter with data stored in volatile memory (RAM) to the factory setting (e.g. measured value data). The device configuration remains unchanged. 12.13 Device information The Device information submenu contains all parameters that display different information for device identification. Navigation "Diagnostics" menu → Device information ‣ Device information Device tag → 142 Serial number → 142 Firmware version → 142 Order code → 143 Extended order code 1 → 143 Extended order code 2 → 143 Extended order code 3 → 143 ENP version → 143 Parameter overview with brief description Parameter Description User interface / User entry Factory setting Device tag Shows name of measuring point. Max. 32 characters, such as letters, numbers or special characters (e.g. @, %, /). – Serial number Shows the serial number of the measuring device. Max. 11-digit character string comprising letters and numbers. – Firmware version Shows the device firmware version installed. Character string in the format xx.yy.zz – Device name Shows the name of the transmitter. Max. 32 characters such as letters or numbers. – 142 The name can be found on the nameplate of the transmitter. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Parameter Order code Diagnosis and troubleshooting Description User interface / User entry Shows the device order code. Character string composed of letters, numbers and certain punctuation marks (e.g. /). – Character string – Character string – Character string – The order code can be found on the nameplate of the sensor and Factory setting transmitter in the "Order code" field. Extended order code 1 Shows the 1st part of the extended order code. extended order code can also be The found on the nameplate of the sensor and transmitter in the "Ext. ord. cd." field. Extended order code 2 Shows the 2nd part of the extended order code. extended order code can also be The found on the nameplate of the sensor and transmitter in the "Ext. ord. cd." field. Extended order code 3 Shows the 3rd part of the extended order code. extended order code can also be The found on the nameplate of the sensor and transmitter in the "Ext. ord. cd." field. ENP version Shows the version of the electronic nameplate (ENP). Character string – IP address IP address of the Web server integrated in the measuring device. 4 octet: 0 to 255 (in the particular octet) – 4 octet: 0 to 255 (in the particular octet) – 4 octet: 0 to 255 (in the particular octet) – If the DHCP client is switched off and write access is enabled, the IP address can also be entered. Subnet mask Displays the subnet mask. If the DHCP client is switched off and write access is enabled, the Subnet mask can also be entered. Default gateway Displays the default gateway. If the DHCP client is switched off and write access is enabled, the Default gateway can also be entered. Endress+Hauser 143 Diagnosis and troubleshooting Proline Prosonic Flow I 400 Modbus RS485 12.14 Firmware history Release date Firmware version 05.2024 01.00.zz Order code for "Firmware version" Option 77 Firmware changes Original firmware Documentation type Operating Instructions Documentation BA02303D/06/EN/01.24 It is possible to flash the firmware to the current version or the previous version using the service interface. For the compatibility of the firmware version with the previous version, the installed device description files and operating tools, observe the information about the device in the "Manufacturer's information" document. The manufacturer's information is available: • In the Download Area of the Endress+Hauser web site: www.endress.com → Downloads • Specify the following details: • Product root: e.g. 9I4B The product root is the first part of the order code: see the nameplate on the device. • Text search: Manufacturer's information • Media type: Documentation – Technical Documentation 144 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 13 Maintenance 13.1 Maintenance tasks Maintenance No special maintenance work is required. 13.1.1 Exterior cleaning When cleaning the exterior of measuring devices, always use cleaning agents that do not attack the surface of the housing or the seals. 13.2 Measuring and test equipment Endress+Hauser offers a variety of measuring and testing equipment, such as Netilion or device tests. Your Endress+Hauser Sales Center can provide detailed information on the services. List of some of the measuring and testing equipment: → 150 13.3 Endress+Hauser services Endress+Hauser offers a wide variety of services for maintenance such as recalibration, maintenance service or device tests. Your Endress+Hauser Sales Center can provide detailed information on the services. Endress+Hauser 145 Repair Proline Prosonic Flow I 400 Modbus RS485 14 Repair 14.1 General notes 14.1.1 Repair and conversion concept The Endress+Hauser repair and conversion concept provides for the following: • The measuring devices have a modular design. • Spare parts are grouped into logical kits with the associated Installation Instructions. • Repairs are carried out by Endress+Hauser Service or by appropriately trained customers. • Certified devices can only be converted to other certified devices by Endress+Hauser Service or at the factory. 14.1.2 Notes for repair and conversion For repair and conversion of a measuring device, observe the following notes: ‣ Use only original Endress+Hauser spare parts. ‣ Carry out the repair according to the Installation Instructions. ‣ Observe the applicable standards, federal/national regulations, Ex documentation (XA) and certificates. ‣ Document all repairs and conversions and enter the details in Netilion Analytics. 14.2 Spare parts Device Viewer (www.endress.com/deviceviewer): All the spare parts for the measuring device, along with the order code, are listed here and can be ordered. If available, users can also download the associated Installation Instructions. Measuring device serial number: • Is located on the nameplate of the device. • Can be read out via the Serial number parameter (→ 142) in the Device information submenu. 14.3 Endress+Hauser services Endress+Hauser offers a wide range of services. Your Endress+Hauser Sales Center can provide detailed information on the services. 14.4 Return The requirements for safe device return can vary depending on the device type and national legislation. 146 1. Refer to the web page for information: https://www.endress.com/support/return-material Select the region. 2. If returning the device, pack the device in such a way that it is reliably protected against impact and external influences. The original packaging offers the best protection. Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 14.5 Repair Disposal If required by the Directive 2012/19/EU on waste electrical and electronic equipment (WEEE), the product is marked with the depicted symbol in order to minimize the disposal of WEEE as unsorted municipal waste. Do not dispose of products bearing this marking as unsorted municipal waste. Instead, return them to the manufacturer for disposal under the applicable conditions. 14.5.1 1. Removing the measuring device Switch off the device. LWARNING Danger to persons from process conditions! ‣ Pay attention to high temperatures. 2. Carry out the mounting and connection steps from the "Mounting the measuring device" and "Connecting the measuring device" sections in reverse order. Observe the safety instructions. 14.5.2 Disposing of the measuring device Observe the following notes during disposal: ‣ Observe valid federal/national regulations. ‣ Ensure proper separation and reuse of the device components. Endress+Hauser 147 Accessories Proline Prosonic Flow I 400 Modbus RS485 15 Accessories Various accessories, which can be ordered with the device or subsequently from Endress +Hauser, are available for the device. Detailed information on the order code in question is available from your local Endress+Hauser sales center or on the product page of the Endress+Hauser website: www.endress.com. 15.1 Device-specific accessories 15.1.1 For the transmitter Accessories Description Transmitter Prosonic Flow 400 Transmitter for replacement or storage. Use the order code to define the following specifications: • Approvals • Output / input • Display/operation • Housing • Software For details, see Installation Instructions EA00104D Post mounting kit Post mounting kit for transmitter. Weather protection cover Is used to protect the measuring device from the effects of the weather: e.g. rainwater, excess heating from direct sunlight. Order number: 71343504 Installation Instructions EA01191D External WLAN antenna External WLAN antenna with 1.5 m (59.1 in) connecting cable and two angle brackets. Order code for "Accessory enclosed", option P8 "Wireless antenna wide area". The external WLAN antenna is not suitable for use in hygienic • applications. • Additional information regarding the WLAN interface → 63. Installation Instructions EA01238D Order number: 71351317 Sensor cable Proline 400 Sensor – transmitter The sensor cable can be ordered directly with the measuring device (order code for "Cable") or as an accessory (order number DK9017). The following cable lengths are available: Temperature: –40 to +80 °C (–40 to +176 °F) • Option AA: 5 m (15 ft) • Option AB: 10 m (30 ft) • Option AC: 15 m (45 ft) • Option AD: 30 m (90 ft) Possible cable length for a Proline 400 sensor cable: max. 30 m (90 ft) 15.1.2 148 For the sensor Accessories Description Sensor set (DK9018) Sensor set 1 MHz (I-100) Sensor holder set (DK9014) Sensor holder set 1 MHz Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Accessories Accessories Description Installation set (DK9016) • Installation set, DN200-DN1800, 8"-72" • Installation set, DN1800-DN4000, 72"-160" Conduit adapter set (DK9003) • Conduit adapter M20x1.5 + sensor cable gland • Conduit adapter NPT1/2'' + sensor cable gland • Conduit adapter G1/2'' + sensor cable gland 15.2 Communication-specific accessories Accessories Description Commubox FXA291 Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser Common Data Interface) and the USB port of a computer or laptop. Technical Information TI405C/07 Fieldgate FXA42 Transmission of the measured values of connected 4 to 20 mA analog measuring devices, as well as digital measuring devices Technical Information TI01297S •• Operating Instructions BA01778S • Product page: www.endress.com/fxa42 Field Xpert SMT50 The Field Xpert SMT50 table PC for device configuration enables mobile plant asset management. It is suitable for commissioning and maintenance staff to manage field instruments with a digital communication interface and to record progress. This tablet PC is designed as an all-in-one solution with a preinstalled driver library and is an easy-to-use, touch-sensitive tool which can be used to manage field instruments throughout their entire life cycle. Technical Information TI01555S •• Operating Instructions BA02053S • Product page: www.endress.com/smt50 Field Xpert SMT70 The Field Xpert SMT70 tablet PC for device configuration enables mobile plant asset management in hazardous and non-hazardous areas. It is suitable for commissioning and maintenance staff to manage field instruments with a digital communication interface and to record progress. This tablet PC is designed as an all-in-one solution with a preinstalled driver library and is an easy-to-use, touch-sensitive tool which can be used to manage field instruments throughout their entire life cycle. Technical Information TI01342S •• Operating Instructions BA01709S • Product page: www.endress.com/smt70 Field Xpert SMT77 The Field Xpert SMT77 tablet PC for device configuration enables mobile plant asset management in areas categorized as Ex Zone 1. Technical Information TI01418S •• Operating Instructions BA01923S • Product page: www.endress.com/smt77 Endress+Hauser 149 Accessories Proline Prosonic Flow I 400 Modbus RS485 15.3 Service-specific accessories Accessories Description Applicator Software for selecting and sizing Endress+Hauser measuring devices: • Choice of measuring devices for industrial requirements • Calculation of all the necessary data for identifying the optimum flowmeter: e.g. nominal diameter, pressure loss, flow velocity and accuracy. • Graphic illustration of the calculation results • Determination of the partial order code, administration, documentation and access to all project-related data and parameters over the entire life cycle of a project. Applicator is available: • Via the Internet: https://portal.endress.com/webapp/applicator • As a downloadable DVD for local PC installation. Netilion lloT ecosystem: Unlock knowledge Endress+Hauser 's Netilion lloT ecosystem enables you to optimize your plant performance, digitize workflows, share knowledge and improve collaboration. Based on decades of experience in process automation, Endress+Hauser offers the process industry an lloT ecosystem that enables you to gain useful insights from data. This knowledge can be used to optimize processes, leading to higher plant availability, efficiency and reliability, and ultimately to a more profitable plant. www.netilion.endress.com FieldCare FDT-based plant asset management tool from Endress+Hauser. It can configure all smart field units in your system and helps you manage them. By using the status information, it is also a simple but effective way of checking their status and condition. Operating Instructions BA00027S and BA00059S DeviceCare Tool to connect and configure Endress+Hauser field devices. Innovation brochure IN01047S Commubox FXA291 Connects Endress+Hauser field devices with a CDI interface (= Endress +Hauser Common Data Interface) and the USB port of a computer or laptop. Technical Information TI00405C 15.4 System components Accessories Description Memograph M graphic data manager The Memograph M graphic data manager provides information on all the relevant measured variables. Measured values are recorded correctly, limit values are monitored and measuring points analyzed. The data are stored in the 256 MB internal memory and also on a SD card or USB stick. Information TI00133R •• Technical Operating Instructions BA00247R 150 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 16 Technical data 16.1 Application Technical data The measuring device is intended only for the flow measurement of liquids. To ensure that the device remains in proper operating condition for its service life, use the measuring device only for media against which the process-wetted materials are sufficiently resistant. 16.2 Function and system design Measuring principle Proline Prosonic Flow uses a measurement method based on the transit time difference. Measuring system The measuring system consists of a transmitter and one or two sensor sets. The transmitter and sensor sets are mounted in physically separate locations. They are interconnected by sensor cables. The sensors function as sound generators and sound receivers. The sensors in a sensor pair are always arranged opposite one another and send/receive the ultrasonic signals directly (1-traverse positioning) → 22. The transmitter serves to control the sensor sets, to prepare, process and evaluate the measuring signals, and to convert the signals to the desired output variable. Information on the structure of the device → 13 16.3 Measured variable Input Direct measured variables • Volume flow • Flow velocity • Sound velocity Calculated measured variables Mass flow Measuring range v = 0 to 15 m/s (0 to 50 ft/s) Operable flow range Over 150 : 1 Input signal External measured values The measuring device has an optional interface via which an externally measured variable (temperature) can be transmitted to the measuring device: digital input (via HART input or Modbus) Various pressure transmitters can be ordered from Endress+Hauser: see "Accessories" section → 150 Endress+Hauser 151 Technical data Proline Prosonic Flow I 400 Modbus RS485 Status input Maximum input values • DC 30 V • 6 mA Response time Configurable: 5 to 200 ms Input signal level • Low signal (low): DC –3 to +5 V • High signal (high): DC 12 to 30 V Assignable functions • Off • Reset totalizers 1-3 separately • Reset all totalizers • Flow override 16.4 Output signal Output Current output Current output Can be set as: • 4 to 20 mA NAMUR • 4 to 20 mA US • 4 to 20 mA HART • 0 to 20 mA Maximum output values • DC 24 V (when idle) • 22.5 mA Load 250 to 700 Ω Resolution 0.38 µA Damping Configurable: 0 to 999.9 s Assignable measured variables • Volume flow • Mass flow • Sound velocity • Flow velocity • Electronics temperature range of options increases if the measuring device has one or more The application packages. Pulse/frequency/switch output Function • With the order code for "Output; Input", option H: output 2 can be set as a pulse or frequency output • With the order code for "Output; Input", option I: output 2 and 3 can be set as a pulse, frequency or switch output Version Passive, open collector Maximum input values • DC 30 V • 250 mA Voltage drop At 25 mA: ≤ DC 2 V Pulse output Pulse width Configurable: 0.05 to 2 000 ms Maximum pulse rate 10 000 Impulse/s Pulse value Configurable Assignable measured variables • Volume flow • Mass flow Frequency output Output frequency 152 Configurable: 0 to 12 500 Hz Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data Damping Configurable: 0 to 999 s Pulse/pause ratio 1:1 Assignable measured variables • Volume flow • Mass flow • Sound velocity • Flow velocity • Electronics temperature Switch output Switching behavior Binary, conductive or non-conductive Switching delay Configurable: 0 to 100 s Number of switching cycles Unlimited Assignable functions • Off • On • Diagnostic behavior • Limit value • Volume flow • Mass flow • Sound velocity • Flow velocity • Totalizer 1-3 • Electronics temperature • Flow direction monitoring • Status Low flow cut off Modbus RS485 Signal on alarm Physical interface In accordance with EIA/TIA-485-A standard Terminating resistor Integrated, can be activated via DIP switch on the transmitter electronics module Depending on the interface, failure information is displayed as follows: Current output 4 to 20 mA 4 to 20 mA Failure mode Choose from: • 4 to 20 mA in accordance with NAMUR recommendation NE 43 • 4 to 20 mA in accordance with US • Min. value: 3.59 mA • Max. value: 22.5 mA • Definable value between: 3.59 to 22.5 mA • Actual value • Last valid value 0 to 20 mA Failure mode Endress+Hauser Choose from: • Max. alarm: 22 mA • Definable value between: 0 to 22.5 mA 153 Technical data Proline Prosonic Flow I 400 Modbus RS485 Pulse/frequency/switch output Pulse output Fault mode Choose from: • Actual value • No pulses Frequency output Fault mode Choose from: • Actual value • 0 Hz • Definable value between: 0 to 12 500 Hz Switch output Fault mode Choose from: • Current status • Open • Closed Modbus RS485 Failure mode Choose from: • NaN value instead of current value • Last valid value Local display Plain text display With information on cause and remedial measures Backlight Red lighting indicates a device error. Status signal as per NAMUR recommendation NE 107 Interface/protocol • Via digital communication: Modbus RS485 • Via service interface • CDI-RJ45 service interface • WLAN interface Plain text display With information on cause and remedial measures Web browser Plain text display With information on cause and remedial measures Light emitting diodes (LED) Status information Status indicated by various light emitting diodes The following information is displayed depending on the device version: • Supply voltage active • Data transmission active • Device alarm/error has occurred Diagnostic information via light emitting diodes → 127 154 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data Low flow cut off The switch points for low flow cut off are user-selectable. Galvanic isolation The following connections are galvanically isolated from each other: • Outputs • Power supply Protocol-specific data Protocol-specific data Protocol Modbus Applications Protocol Specification V1.1 Response times • Direct data access: typically 25 to 50 ms • Auto-scan buffer (data range): typically 3 to 5 ms Device type Slave Slave address range 1 to 247 Broadcast address range 0 Function codes • 03: Read holding register • 04: Read input register • 06: Write single registers • 08: Diagnostics • 16: Write multiple registers • 23: Read/write multiple registers Broadcast messages Supported by the following function codes: • 06: Write single registers • 16: Write multiple registers • 23: Read/write multiple registers Supported baud rate • 1 200 BAUD • 2 400 BAUD • 4 800 BAUD • 9 600 BAUD • 19 200 BAUD • 38 400 BAUD • 57 600 BAUD • 115 200 BAUD Data transmission mode • ASCII • RTU Data access Each device parameter can be accessed via Modbus RS485. For Modbus register information System integration Information regarding system integration → 69. • Modbus RS485 information • Function codes • Register information • Response time • Modbus data map 16.5 Terminal assignment Endress+Hauser Power supply → 35 155 Technical data Supply voltage Proline Prosonic Flow I 400 Modbus RS485 Transmitter Order code for "Power supply" Option L Power consumption Current consumption terminal voltage Frequency range DC 24 V ±25% – AC 24 V ±25% 50/60 Hz, ±4 Hz AC 100 to 240 V –15 to +10% 50/60 Hz, ±4 Hz Order code for "Output" Maximum power consumption Option M: Modbus RS485 30 VA/8 W Option O: Modbus RS485, 4-20mA, 2 x pulse/ frequency/switch output 30 VA/8 W Transmitter Order code for "Power supply" Maximum Current consumption Maximum switch-on current Option L: AC 100 to 240 V 145 mA 25 A (< 5 ms) Option L: AC/DC 24 V 350 mA 27 A (< 5 ms) Device fuse Fine-wire fuse (slow-blow): • DC 24 V: T1A • AC 100 to 240 V: T1A Power supply failure • Totalizers stop at the last value measured. • Depending on the device version, the configuration is retained in the device memory or in the pluggable data memory (HistoROM DAT). • Error messages (incl. total operated hours) are stored. Overcurrent protection element The device must be operated with a dedicated circuit breaker, as it does not have an ON/OFF switch of its own. • The circuit breaker must be easy to reach and labeled accordingly. • Permitted nominal current of the circuit breaker: 2 A up to maximum 10 A. Electrical connection → 37 Potential equalization → 39 Terminals Transmitter Supply voltage cable: plug-in spring terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG) Cable entries Cable entry thread • M20 x 1.5 • Via adapter: • NPT ½" • G ½" 156 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data Cable gland M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in) If metal cable entries are used, use a grounding plate. Cable specification → 34 Overvoltage protection Mains voltage fluctuations → 156 Overvoltage category Overvoltage category II Short-term, temporary overvoltage Between cable and ground up to 1200 V, for max. 5 s Long-term, temporary overvoltage Between cable and ground up to 500 V 16.6 Reference operating conditions Performance characteristics • Maximum permissible error according to ISO/DIN 11631 • Specifications as per measurement report • Accuracy information is based on accredited calibration rigs that are traced to ISO 17025. To obtain measured errors, use the Applicator sizing tool → 150 Maximum measurement error o.r. = of reading The measurement error depends on a number of factors. A distinction is made between the measurement error of the device (0.5% o.r.) and an additional installation-specific measurement error (typically 1.5% o.r.) that is independent of the device. The installation-specific measurement error depends on the installation conditions on site, such as the nominal diameter, accuracy of sensor mounting (sensor holder welding), real pipe geometry or medium. The sum of the two measurement errors is the measurement error at the measuring point. [%] 3.5 3 2.0 2 0.5 1 0 0 2 4 10 6 20 8 10 30 12 40 14 [m/s] 50 [ft/s] A0041972 25 1 2 3 Endress+Hauser Example of the measurement error in a pipe with a nominal diameter DN > 200 (8") Measurement error of measuring device: 0.5% o.r. ± 3 mm/s (0.12 in/s) Measurement error due to installation conditions: typically 1.5% o.r. Measurement error at the measuring point: 0.5% o.r. ± 3 mm/s (0.12 in/s) + 1.5% o.r. = 2% o.r. ± 3 mm/s (0.12 in/s) 157 Technical data Proline Prosonic Flow I 400 Modbus RS485 Measurement error at the measuring point The measurement error at the measuring point is made up of the measurement error of the device (0.5% o.r.) and the measurement error resulting from the installation conditions on site. With a flow velocity > 0.3 m/s (1 ft/s) and a Reynolds number > 10 000, the following are typical error limits: Nominal diameter Maximum permissible errors for device + Installation-specific maximum permissible errors (typical) → Maximum permissible errors at the measuring point (typical) Field calibration 1) ≥ DN 200 (8") ±0.5% o.r. ± 3 mm/s (0.12 in/s) + ±1.5% o.r. → ±2% o.r. ± 3 mm/s (0.12 in/s) ±0.5% o.r. ± 3 mm/s (0.12 in/s) 1) Adjustment in relation to a reference value with correction values written back to the transmitter Measurement report If required, the device can be supplied with a factory measurement report. A measurement is performed under reference conditions to verify the performance of the device. Here, the sensors are mounted on a pipe with a nominal diameter of DN 250 (10") or 400 (16"). With a flow velocity of > 0.3 m/s (1 ft/s) and a Reynolds number > 10 000, the following error limits are guaranteed with the measurement report: Nominal diameter Maximum permissible errors for device 250 (10"); single-path ±0.5% o.r. ± 3 mm/s (0.12 in/s) 400 (16"); dual-path ±0.5% o.r. ± 3 mm/s (0.12 in/s) The specification applies to Reynolds numbers Re ≥ 10 000. Larger measurement errors may occur for Reynolds numbers Re < 10 000. 158 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data Example of max. measurement error (volume flow) [%] 4.0 3.5 3.0 2.5 2.0 1 1.5 1.0 0.5 0.0 2 0 0 4 0.1 6 0.2 8 0.3 10 0.4 12 0.5 14 [m/s] 0.6 [ft/s] A0045278 26 1 Example of max. measurement error (volume flow) in % o.r. Pipe diameter ≥ 250 (10") Accuracy of outputs The outputs have the following base accuracy specifications. Repeatability o.r. = of reading ±0.3% for flow velocities >0.3 m/s (1 ft/s) Influence of ambient temperature Current output o.r. = of reading Temperature coefficient Max. ±0.005 % o.r./°C Pulse/frequency output Temperature coefficient 16.7 Mounting requirements Endress+Hauser No additional effect. Included in accuracy. Mounting → 19 159 Technical data Proline Prosonic Flow I 400 Modbus RS485 16.8 Environment Ambient temperature range → 23 Storage temperature The storage temperature for all components (except display modules and order code for "Sensor version", options AG, AH) corresponds to the ambient temperature range→ 23. Display modules –40 to +60 °C (–40 to +140 °F) Relative humidity The device is suitable for use outdoors and indoors with a relative humidity of 5 to 95 %. Operating height According to EN 61010-1 • ≤ 2 000 m (6 562 ft) • > 2 000 m (6 562 ft) with additional overvoltage protection (e.g. Endress+Hauser HAW Series) Degree of protection Transmitter • IP66/67, type 4X enclosure, suitable for pollution degree 4 • When the housing is open: IP20, type 1 enclosure, suitable for pollution degree 2 • Display module: IP20, type 1 enclosure, suitable for pollution degree 2 Sensor • Standard: IP66/67, type 4X enclosure, suitable for pollution degree 4 • Optionally available: IP68, type 6P enclosure, suitable for pollution degree 4 External WLAN antenna IP67 Shock and vibration resistance Vibration sinusoidal, in accordance with IEC 60068-2-6 • 2 to 8.4 Hz, 7.5 mm peak • 8.4 to 2 000 Hz, 2 g peak Vibration broad-band random, according to IEC 60068-2-64 • 10 to 200 Hz, 0.01 g2/Hz • 200 to 2 000 Hz, 0.003 g2/Hz • Total: 2.70 g rms Shock half-sine, according to IEC 60068-2-27 6 ms 50 g Rough handling shocks according to IEC 60068-2-31 160 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Electromagnetic compatibility (EMC) Technical data • As per IEC/EN 61326 and NAMUR Recommendation 21 (NE 21) • As per IEC/EN 61000-6-2 and IEC/EN 61000-6-4 • Complies with emission limits for industry as per EN 55011 (Class A) Details are provided in the Declaration of Conformity. This unit is not intended for use in residential environments and cannot guarantee adequate protection of the radio reception in such environments. 16.9 Medium temperature range Process Sensor version Frequency Temperature I-100-A 1 MHz –40 to +80 °C (–40 to +176 °F) Sound velocity range 600 to 3 000 m/s (1 969 to 9 843 ft/s) Medium pressure range Maximum nominal pressure PN 16 (16 bar (232 psi)) Flow limit For an overview of the full scale values for the measuring range, see the "Measuring range" section • The minimum recommended full scale value is approx. 1/20 of the maximum full scale value. • In most applications, 10 to 50 % of the maximum full scale value can be considered ideal. Pressure loss There is no pressure loss. 16.10 Mechanical Construction Design, dimensions Weight For the dimensions and installation lengths of the device, see the "Technical Information" document, "Mechanical construction" section Weight specifications exclusive of packaging material. Transmitter • Proline 400 polycarbonate plastic: 1.2 kg (2.65 lb) • Proline 400 aluminum, coated: 6.0 kg (13.2 lb) Sensor Including mounting material • Single path installation version: 4.5 kg (9.92 lb) • Two path installation version: 9 kg (19.9 lb) Materials Remote version (wall-mount housing) • Order code for "Housing", option P "Remote, alu, coated": Aluminum, AlSi10Mg, coated • Order code for "Housing", option N: polycarbonate plastic • Window material: • For order code for "Housing", option P: glass • For order code for "Housing", option N: plastic Endress+Hauser 161 Technical data Proline Prosonic Flow I 400 Modbus RS485 Cable entries/cable glands 1 2 3 A0020640 27 1 2 3 Possible cable entries/cable glands Female thread M20 × 1.5 Cable gland M20 × 1.5 Adapter for cable entry with female thread G ½" or NPT ½" remote version Cable entry/cable gland Material Cable gland M20 × 1.5 • Plastic • Nickel-plated brass Cable gland of sensor cable Nickel-plated brass Power cable gland Plastic Adapter for cable entry with female thread G ½" or NPT ½" Nickel-plated brass Sensor - transmitter cable UV rays can impair the cable outer sheath. Protect the cable from exposure to sun as much as possible. Sensor cable, TPE halogen-free • Cable sheath: TPE halogen-free • Cable plug: nickel-plated brass Ultrasonic transducer • Holder: stainless steel 1.4301 (304), 1.4404 (316L) • Housing: stainless steel 1.4301 (304), 1.4404 (316L) Accessories External WLAN antenna • Antenna: ASA plastic (acrylonitrile styrene acrylate) and nickel-plated brass • Adapter: Stainless steel and nickel-plated brass • Cable: Polyethylene • Plug: Nickel-plated brass • Angle bracket: Stainless steel Process connections Flanges: ASME B16.5 For information on the different materials used in the process connections → 161 162 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data 16.11 Display and user interface Languages Can be operated in the following languages: • Via local operation: English, German, French, Spanish, Italian, Dutch, Portuguese, Polish, Russian, Turkish, Chinese, Japanese, Bahasa (Indonesian), Vietnamese, Czech, Swedish • Via "FieldCare", "DeviceCare" operating tool: English, German, French, Spanish, Italian, Chinese, Japanese Onsite operation Via display module Features: • Standard features 4-line, illuminated, graphic display; touch control • Order code for "Display; operation", option G "4-line, illuminated; touch control +WLAN" offers standard equipment features in addition to access via web browser Information about WLAN interface → 63 A0032074 28 Operation with touch control Display elements • 4-line, illuminated, graphic display • White background lighting; switches to red in event of device errors • Format for displaying measured variables and status variables can be individually configured Operating elements • External operation via touch control (3 optical keys) without opening the housing: , , • Operating elements also accessible in the various zones of the hazardous area Remote operation → 63 Service interface → 63 Supported operating tools Different operating tools can be used for local or remote access to the measuring device. Depending on the operating tool used, access is possible with different operating units and via a variety of interfaces. Endress+Hauser 163 Technical data Proline Prosonic Flow I 400 Modbus RS485 Supported operating tools Operating unit Interface Additional information Web browser Notebook, PC or tablet with web browser • CDI-RJ45 service interface • WLAN interface Special Documentation for device DeviceCare SFE100 Notebook, PC or tablet • CDI-RJ45 service with Microsoft Windows interface system • WLAN interface • Fieldbus protocol → 150 FieldCare SFE500 Notebook, PC or tablet • CDI-RJ45 service with Microsoft Windows interface system • WLAN interface • Fieldbus protocol → 150 Field Xpert SMT70/77/50 • All Fieldbus protocols • WLAN interface • Bluetooth • CDI-RJ45 service interface Operating Instructions BA01202S WLAN → 150 SmartBlue app Smart phone or tablet with iOs or Android Device description files: Use update function of handheld terminal Other operating tools based on FDT technology with a device driver such as DTM/ iDTM or DD/EDD can be used for device operation. These operating tools are available from the individual manufacturers. Integration into the following operating tools, among others, is supported: • Field Device Manager (FDM) from Honeywell → www.process.honeywell.com • FieldMate from Yokogawa → www.yokogawa.com • PACTWare → www.pactware.com The related device description files are available: www.endress.com → Download Area Web server With the integrated web server, the device can be operated and configured via a web browser service interface (CDI-RJ45) or WLAN interface. The structure of the operating menu is the same as for the local display. In addition to the measured values, status information on the device is displayed and can be used to monitor device health. Furthermore the device data can be managed and the network parameters can be configured. Supported functions Data exchange between the operating unit (such as a notebook, for example,) and measuring device: • Upload the configuration from the measuring device (XML format, configuration backup) • Save the configuration to the measuring device (XML format, restore configuration) • Export event list (.csv file) • Export parameter settings (.csv file or PDF file, document the measuring point configuration) • Export the Heartbeat verification report (PDF file, only available with the Heartbeat Verification → 167 application package) • Flash firmware version for device firmware upgrade, for example • Download driver for system integration • Visualize up to 1000 saved measured values (only available with the Extended HistoROM application package→ 167) 164 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 HistoROM data management Technical data The measuring device features HistoROM data management. HistoROM data management comprises both the storage and import/export of key device and process data, making operation and servicing far more reliable, secure and efficient. Additional information on the data storage concept There are different types of data storage units in which device data are stored and used by the device: Available data HistoROM backup T-DAT S-DAT • Event logbook, e.g. diagnostic events • Device firmware package • Measured value logging ("Extended HistoROM" order option) • Current parameter data record (used by firmware at run time) • Indicator (minimum/maximum values) • Totalizer value • Sensor data: e.g. • Serial number • Device configuration (e.g. SW options, fixed I/O or multi I/O) Can be plugged into the user interface PC board in the connection compartment Fixed on the sensor connection board Storage location Fixed on the user interface PC board in the connection compartment Data backup Automatically • The most important device data (sensor and transmitter) are automatically saved in the DAT modules. • If the transmitter or measuring device is replaced: Once the T-DAT containing the previous device data has been exchanged, the new measuring device goes into operation immediately, without any errors. • If the sensor is replaced: Once the S-DAT has been replaced with new device data, the measuring device goes into operation immediately, without any errors. Data transmission Manual Transfer of a device configuration to another device using the export function of the specific operating tool, e.g. with FieldCare, DeviceCare or Web server: to duplicate the configuration or to store in an archive (e.g. for backup purposes) Event list Automatic • Chronological display of up to 20 event messages in the events list • If the Extended HistoROM application package (order option) is enabled: up to 100 event messages are displayed in the events list along with a time stamp, plain text description and remedial measures • The events list can be exported and displayed via a variety of interfaces and operating tools e.g. DeviceCare, FieldCare or Web server Data logging Manual If the Extended HistoROM application package (order option) is enabled: • Recording of 1 to 4 channels of up to 1 000 measured values (up to 250 measured values per channel) • User configurable recording interval • Export the measured value log via a variety of interfaces and operating tools e.g. FieldCare, DeviceCare or web server Endress+Hauser 165 Technical data Proline Prosonic Flow I 400 Modbus RS485 16.12 Certificates and approvals Current certificates and approvals for the product are available at www.endress.com on the relevant product page: CE mark 1. Select the product using the filters and search field. 2. Open the product page. 3. Select Downloads. The device meets the legal requirements of the applicable EU Directives. These are listed in the corresponding EU Declaration of Conformity along with the standards applied. Endress+Hauser confirms successful testing of the device by affixing to it the CE mark. UKCA marking The device meets the legal requirements of the applicable UK regulations (Statutory Instruments). These are listed in the UKCA Declaration of Conformity along with the designated standards. By selecting the order option for UKCA marking, Endress+Hauser confirms a successful evaluation and testing of the device by affixing the UKCA mark. Contact address Endress+Hauser UK: Endress+Hauser Ltd. Floats Road Manchester M23 9NF United Kingdom www.uk.endress.com RCM marking The measuring system meets the EMC requirements of the "Australian Communications and Media Authority (ACMA)". Ex-approval The devices are certified for use in hazardous areas and the relevant safety instructions are provided in the separate "Control Drawing" document. This is referenced on the nameplate. Modbus RS485 certification The measuring device meets all the requirements of the MODBUS RS485 conformity test and has the "MODBUS RS485 Conformance Test Policy, Version 2.0". The measuring device has successfully passed all the test procedures carried out. Radio approval The measuring device has radio approval. For detailed information on the radio approval, see the Special Documentation → 169 External standards and guidelines 166 • EN 60529 Degrees of protection provided by enclosure (IP code) • EN 61010-1 Safety requirements for electrical equipment for measurement, control and laboratory use - general requirements • IEC/EN 61326-2-3 Emission in accordance with Class A requirements. Electromagnetic compatibility (EMC requirements). • ANSI/ISA-61010-1 (82.02.01) Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use - Part 1 General Requirements • CAN/CSA-C22.2 No. 61010-1-12 Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use - Part 1 General Requirements Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data • NAMUR NE 21 Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment • NAMUR NE 32 Data retention in the event of a power failure in field and control instruments with microprocessors • NAMUR NE 43 Standardization of the signal level for the breakdown information of digital transmitters with analog output signal. • NAMUR NE 53 Software of field devices and signal-processing devices with digital electronics • NAMUR NE 105 Specifications for integrating fieldbus devices in engineering tools for field devices • NAMUR NE 107 Self-monitoring and diagnosis of field devices • NAMUR NE 131 Requirements for field devices for standard applications • ETSI EN 300 328 Guidelines for 2.4 GHz radio components. • EN 301489 Electromagnetic compatibility and radio spectrum matters (ERM). 16.13 Application packages Many different application packages are available to enhance the functionality of the device. Such packages might be needed to address safety aspects or specific application requirements. The application packages can be ordered with the device or subsequently from Endress+Hauser. Detailed information on the order code in question is available from your local Endress+Hauser sales center or on the product page of the Endress+Hauser website: www.endress.com. Detailed information on the application packages: Special Documentation → 169 Diagnostic functionality Order code for "Application package", option EA "Extended HistoROM" Comprises extended functions concerning the event log and the activation of the measured value memory. Event log: Memory volume is extended from 20 message entries (standard version) to up to 100 entries. Data logging (line recorder): • Memory capacity for up to 1000 measured values is activated. • 250 measured values can be output via each of the 4 memory channels. The recording interval can be defined and configured by the user. • Measured value logs can be accessed via the local display or operating tool e.g. FieldCare, DeviceCare or Web server. For detailed information, see the Operating Instructions for the device. Heartbeat Technology Endress+Hauser Order code for "Application package", option EB "Heartbeat Verification + Monitoring" 167 Technical data Proline Prosonic Flow I 400 Modbus RS485 Heartbeat Verification Meets the requirement for traceable verification to DIN ISO 9001:2008 Chapter 7.6 a) "Control of monitoring and measuring equipment". • Functional testing in the installed state without interrupting the process. • Traceable verification results on request, including a report. • Simple testing process via local operation or other operating interfaces. • Clear measuring point assessment (pass/fail) with high test coverage within the framework of manufacturer specifications. • Extension of calibration intervals according to operator's risk assessment. Heartbeat Monitoring Continuously supplies data, which are characteristic of the measuring principle, to an external condition monitoring system for the purpose of preventive maintenance or process analysis. These data enable the operator to: • Draw conclusions - using these data and other information - about the impact the measuring application has on the measuring performance over time. • Schedule servicing in time. • Monitor the process or product quality, e.g. gas pockets . For detailed information, see the Special Documentation for the device. 16.14 Accessories Overview of accessories available to order → 148 16.15 Supplemental documentation For an overview of the scope of the associated Technical Documentation, refer to the following: • Device Viewer (www.endress.com/deviceviewer): Enter the serial number from the nameplate • Endress+Hauser Operations app: Enter serial number from nameplate or scan matrix code on nameplate. Standard documentation Brief operating instructions Brief Operating Instructions for the sensor Measuring device Documentation code Proline Prosonic Flow I KA01511D Brief operating instructions for transmitter Documentation code Measuring device HART Modbus RS485 Proline 400 KA01510D KA01660D Technical Information Measuring device Documentation code Prosonic Flow I 400 TI01567D 168 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Technical data Description of device parameters Documentation code Measuring device HART Modbus RS485 Prosonic Flow I 400 GP01166D GP01208D Device-dependent additional documentation Special documentation Content Documentation code Radio approvals for WLAN interface for A309/A310 display module SD01793D Heartbeat Technology SD03132D Installation instructions Contents Note Installation instructions for spare part sets and accessories • Access the overview of all the available spare part sets via Device Viewer → 146 • Accessories available for order with Installation Instructions → 148 Endress+Hauser 169 Index Proline Prosonic Flow I 400 Modbus RS485 Index A Access authorization to parameters Read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Access code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Incorrect input . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Adapting the diagnostic behavior . . . . . . . . . . . . . . . 134 Ambient conditions Operating height . . . . . . . . . . . . . . . . . . . . . . . . 160 Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . 160 Shock and vibration resistance . . . . . . . . . . . . . . 160 Storage temperature . . . . . . . . . . . . . . . . . . . . . . 160 Ambient temperature Influence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Ambient temperature range . . . . . . . . . . . . . . . . 23, 160 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Application packages . . . . . . . . . . . . . . . . . . . . . . . . 167 Applicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Auto scan buffer see Modbus RS485 Modbus data map C Cable entries Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Cable entry Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 40 CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 166 Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Check Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Installation status . . . . . . . . . . . . . . . . . . . . . . . . . 88 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Checklist Post-connection check . . . . . . . . . . . . . . . . . . . . . 41 Post-mounting check . . . . . . . . . . . . . . . . . . . . . . 32 Cleaning Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . 145 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Advanced settings . . . . . . . . . . . . . . . . . . . . . . . 103 Configuring the measuring device . . . . . . . . . . . . . 74 Configuring error response mode, Modbus RS485 . . 134 Connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Connecting the measuring device . . . . . . . . . . . . . . . . 37 Connection see Electrical connection Connection preparations . . . . . . . . . . . . . . . . . . . . . . 36 Connection tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Context menu Calling up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Current consumption . . . . . . . . . . . . . . . . . . . . . . . . 156 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . 10 Defining the access code . . . . . . . . . . . . . . . . . . . . . 115 Degree of protection . . . . . . . . . . . . . . . . . . . . . 40, 160 Design Measuring device . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Device components . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Device description files . . . . . . . . . . . . . . . . . . . . . . . 68 Device fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Device locking, status . . . . . . . . . . . . . . . . . . . . . . . 117 Device name Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Device repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Device revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Device type code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Device Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 146 DeviceCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Device description file . . . . . . . . . . . . . . . . . . . . . . 68 Diagnosis Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Diagnostic behavior Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Diagnostic information Communication interface . . . . . . . . . . . . . . . . . . 134 Design, description . . . . . . . . . . . . . . . . . . . 130, 133 DeviceCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Light emitting diodes . . . . . . . . . . . . . . . . . . . . . 127 Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Remedial measures . . . . . . . . . . . . . . . . . . . . . . 135 Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Diagnostic message . . . . . . . . . . . . . . . . . . . . . . . . . 129 Diagnostics list . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 DIP switch see Write protection switch Direct access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Disabling write protection . . . . . . . . . . . . . . . . . . . . 114 Display see Local display Display area For operational display . . . . . . . . . . . . . . . . . . . . . 45 In the navigation view . . . . . . . . . . . . . . . . . . . . . 47 Display values For locking status . . . . . . . . . . . . . . . . . . . . . . . . 117 Displaying the measured value history . . . . . . . . . . . 123 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Document Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Document function . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 D Date of manufacture . . . . . . . . . . . . . . . . . . . . . . . . . 16 170 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 Index E Electrical connection Computer with web browser (e.g. Microsoft Edge) 63 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 40 Measuring device . . . . . . . . . . . . . . . . . . . . . . . . . 34 Operating tool (e.g. FieldCare, DeviceCare, AMS Device Manager, SIMATIC PDM) . . . . . . . . . . . . . . 63 Operating tools Via Modbus RS485 protocol . . . . . . . . . . . . . . . 63 Via service interface (CDI-RJ45) . . . . . . . . . . . . 63 Via WLAN interface . . . . . . . . . . . . . . . . . . . . 63 Web server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 WLAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Electromagnetic compatibility . . . . . . . . . . . . . . . . . 161 Enabling write protection . . . . . . . . . . . . . . . . . . . . 114 Enabling/disabling the keypad lock . . . . . . . . . . . . . . 56 Endress+Hauser services Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Error messages see Diagnostic messages Event logbook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Events list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Ex-approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Extended order code Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 F Field of application Residual risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Field Xpert SMT70 . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Field Xpert SMT77 . . . . . . . . . . . . . . . . . . . . . . . . . . 67 FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Device description file . . . . . . . . . . . . . . . . . . . . . . 68 Establishing a connection . . . . . . . . . . . . . . . . . . . 65 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 User interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Filtering the event logbook . . . . . . . . . . . . . . . . . . . 140 Firmware Release date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Firmware history . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Flow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Flow limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 FlowDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Function codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Functions see Parameter G Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . 155 H Hardware write protection . . . . . . . . . . . . . . . . . . . . 116 Help text Calling up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Endress+Hauser Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 I I/O electronics module . . . . . . . . . . . . . . . . . . . . . 14, 39 Identifying the measuring device . . . . . . . . . . . . . . . . 15 Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . . . . 15 Indication Current diagnostic event . . . . . . . . . . . . . . . . . . . 138 Previous diagnostic event . . . . . . . . . . . . . . . . . . 138 Influence Ambient temperature . . . . . . . . . . . . . . . . . . . . . 159 Information on this document . . . . . . . . . . . . . . . . . . . 6 Inlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Input screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Inspection Received goods . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Installation dimensions . . . . . . . . . . . . . . . . . . . . . . . 22 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 L Languages, operation options . . . . . . . . . . . . . . . . . 163 Line recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Editing view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Navigation view . . . . . . . . . . . . . . . . . . . . . . . . . . 47 see Diagnostic message see In alarm condition see Operational display Low flow cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 M Main electronics module . . . . . . . . . . . . . . . . . . . . . . 14 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Maintenance tasks . . . . . . . . . . . . . . . . . . . . . . . . . 145 Manufacturer ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Maximum measurement error . . . . . . . . . . . . . . . . . 157 Measured variables Calculated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Measured . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 see Process variables Measuring and test equipment . . . . . . . . . . . . . . . . 145 Measuring device Configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Preparing for electrical connection . . . . . . . . . . . . 36 Preparing for mounting . . . . . . . . . . . . . . . . . . . . 25 Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Measuring mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . 151 Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Measuring range, recommended . . . . . . . . . . . . . . . 161 Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . 151 171 Index Menu Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Menus For measuring device configuration . . . . . . . . . . . . 74 For specific settings . . . . . . . . . . . . . . . . . . . . . . 103 Modbus RS485 Configuring error response mode . . . . . . . . . . . . 134 Diagnostic information . . . . . . . . . . . . . . . . . . . . 134 Function codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Modbus data map . . . . . . . . . . . . . . . . . . . . . . . . . 71 Read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Reading out data . . . . . . . . . . . . . . . . . . . . . . . . . 72 Register addresses . . . . . . . . . . . . . . . . . . . . . . . . 70 Register information . . . . . . . . . . . . . . . . . . . . . . 70 Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Scan list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Modbus RS485 certification . . . . . . . . . . . . . . . . . . . 166 Mounting dimensions see Installation dimensions Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Mounting preparations . . . . . . . . . . . . . . . . . . . . . . . 25 Mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . 19 Mounting requirements Inlet and outlet runs . . . . . . . . . . . . . . . . . . . . . . . 20 Installation dimensions . . . . . . . . . . . . . . . . . . . . 22 Mounting location . . . . . . . . . . . . . . . . . . . . . . . . 19 Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Mounting tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 N Nameplate Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Navigation path (navigation view) . . . . . . . . . . . . . . . 47 Navigation view In the submenu . . . . . . . . . . . . . . . . . . . . . . . . . . 47 In the wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Netilion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Numeric editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 O Operable flow range . . . . . . . . . . . . . . . . . . . . . . . . 151 Operating elements . . . . . . . . . . . . . . . . . . . . . . 50, 130 Operating height . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Operating keys see Operating elements Operating menu Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Menus, submenus . . . . . . . . . . . . . . . . . . . . . . . . 43 Submenus and user roles . . . . . . . . . . . . . . . . . . . 44 Operating philosophy . . . . . . . . . . . . . . . . . . . . . . . . 44 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Operation methods . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Operation options . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Operational display . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 172 Proline Prosonic Flow I 400 Modbus RS485 Orientation (vertical, horizontal) . . . . . . . . . . . . . . . . 20 Outlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Output variables . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 P Packaging disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Parameter settings Administration (Submenu) . . . . . . . . . . . . . . . . . 112 Advanced setup (Submenu) . . . . . . . . . . . . . . . . 104 Communication (Submenu) . . . . . . . . . . . . . . . . . 82 Current output 1 (Wizard) . . . . . . . . . . . . . . . . . . 89 Data logging (Submenu) . . . . . . . . . . . . . . . . . . . 123 Define access code (Wizard) . . . . . . . . . . . . . . . . 111 Device information (Submenu) . . . . . . . . . . . . . . 142 Diagnostics (Menu) . . . . . . . . . . . . . . . . . . . . . . 138 Display (Submenu) . . . . . . . . . . . . . . . . . . . . . . . 106 Display (Wizard) . . . . . . . . . . . . . . . . . . . . . . . . . 99 Double pulse output . . . . . . . . . . . . . . . . . . . . . . . 98 Double pulse output (Wizard) . . . . . . . . . . . . . . . . 98 Heartbeat base settings (Submenu) . . . . . . . . . . . 111 Input values (Submenu) . . . . . . . . . . . . . . . . . . . 119 Installation status (Submenu) . . . . . . . . . . . . . . . . 88 Low flow cut off (Wizard) . . . . . . . . . . . . . . . . . . 101 Measuring point (Wizard) . . . . . . . . . . . . . . . . . . 83 Output values (Submenu) . . . . . . . . . . . . . . . . . . 120 Process variables (Submenu) . . . . . . . . . . . . . . . . 118 Pulse/frequency/switch output 1 to n (Wizard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92, 93, 94 Relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Relay output 1 to n (Wizard) . . . . . . . . . . . . . . . . . 96 Reset access code (Submenu) . . . . . . . . . . . . . . . 112 Sensor adjustment (Submenu) . . . . . . . . . . . . . . 104 Setup (Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Simulation (Submenu) . . . . . . . . . . . . . . . . . . . . 112 System units (Submenu) . . . . . . . . . . . . . . . . . . . . 81 System values (Submenu) . . . . . . . . . . . . . . . . . . 119 Totalizer (Submenu) . . . . . . . . . . . . . . . . . . . . . . 121 Totalizer 1 to n (Submenu) . . . . . . . . . . . . . . . . . 104 Totalizer handling (Submenu) . . . . . . . . . . . . . . . 122 Web server (Submenu) . . . . . . . . . . . . . . . . . . . . . 62 WLAN settings (Wizard) . . . . . . . . . . . . . . . . . . 108 Parameters Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Enter a value . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Performance characteristics . . . . . . . . . . . . . . . . . . . 157 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . 74 Post-connection check (checklist) . . . . . . . . . . . . . . . 41 Post-mounting check . . . . . . . . . . . . . . . . . . . . . . . . . 74 Post-mounting check (checklist) . . . . . . . . . . . . . . . . 32 Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . 39 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . 156 Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . 156 Pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Process connections . . . . . . . . . . . . . . . . . . . . . . . . 162 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Protecting parameter settings . . . . . . . . . . . . . . . . . 114 Endress+Hauser Proline Prosonic Flow I 400 Modbus RS485 R Radio approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 RCM marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Reading off measured values . . . . . . . . . . . . . . . . . . 117 Reading out diagnostic information, Modbus RS485 134 Recalibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Reference operating conditions . . . . . . . . . . . . . . . . 157 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remedial measures Calling up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Remote version Connecting the signal cables . . . . . . . . . . . . . . . . . 37 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Repair of a device . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Repeatability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Replacement Device components . . . . . . . . . . . . . . . . . . . . . . . 146 Requirements for personnel . . . . . . . . . . . . . . . . . . . . . 9 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 S Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Sensor set selection and arrangement . . . . . . . . . . . . 22 Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setting the operating language . . . . . . . . . . . . . . . . . 74 Settings Adapting the measuring device to the process conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Advanced display configurations . . . . . . . . . . . . . 106 Communication interface . . . . . . . . . . . . . . . . . . . 82 Current output . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Double pulse output . . . . . . . . . . . . . . . . . . . . . . . 98 Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Low flow cut off . . . . . . . . . . . . . . . . . . . . . . . . . 101 Measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Operating language . . . . . . . . . . . . . . . . . . . . . . . 74 Pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Pulse/frequency/switch output . . . . . . . . . . . . 90, 93 Relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Resetting the device . . . . . . . . . . . . . . . . . . . . . . 141 Resetting the totalizer . . . . . . . . . . . . . . . . . . . . 122 Sensor adjustment . . . . . . . . . . . . . . . . . . . . . . . 104 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Switch output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 System units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Totalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Totalizer reset . . . . . . . . . . . . . . . . . . . . . . . . . . 122 WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Shock and vibration resistance . . . . . . . . . . . . . . . . . 160 Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Software release . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Sound velocity range . . . . . . . . . . . . . . . . . . . . . . . . 161 Spare part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Endress+Hauser Index Special connection instructions . . . . . . . . . . . . . . . . . 40 Standards and guidelines . . . . . . . . . . . . . . . . . . . . . 166 Status area For operational display . . . . . . . . . . . . . . . . . . . . . 45 In the navigation view . . . . . . . . . . . . . . . . . . . . . 47 Status signals . . . . . . . . . . . . . . . . . . . . . . . . . 129, 132 Storage concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Storage conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . 18 Storage temperature range . . . . . . . . . . . . . . . . . . . 160 Submenu Administration . . . . . . . . . . . . . . . . . . . . . . 111, 112 Advanced setup . . . . . . . . . . . . . . . . . . . . . 103, 104 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Data logging . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Device information . . . . . . . . . . . . . . . . . . . . . . . 142 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Events list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Heartbeat base settings . . . . . . . . . . . . . . . . . . . 111 Heartbeat setup . . . . . . . . . . . . . . . . . . . . . . . . . 110 Input values . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Installation status . . . . . . . . . . . . . . . . . . . . . . . . . 88 Measured values . . . . . . . . . . . . . . . . . . . . . . . . 117 Output values . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Process variables . . . . . . . . . . . . . . . . . . . . . . . . 118 Reset access code . . . . . . . . . . . . . . . . . . . . . . . . 112 Sensor adjustment . . . . . . . . . . . . . . . . . . . . . . . 104 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 System units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 System values . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Totalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Totalizer 1 to n . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Totalizer handling . . . . . . . . . . . . . . . . . . . . . . . 122 Web server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Symbols For communication . . . . . . . . . . . . . . . . . . . . . . . 45 For correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 For diagnostic behavior . . . . . . . . . . . . . . . . . . . . 45 For locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 For measured variable . . . . . . . . . . . . . . . . . . . . . 45 For measurement channel number . . . . . . . . . . . . 45 For menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 For parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 For status signal . . . . . . . . . . . . . . . . . . . . . . . . . . 45 For submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 For wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 In the status area of the local display . . . . . . . . . . . 45 In the text and numeric editor . . . . . . . . . . . . . . . . 49 System design Measuring system . . . . . . . . . . . . . . . . . . . . . . . 151 see Measuring device design System integration . . . . . . . . . . . . . . . . . . . . . . . . . . 68 T Technical data, overview . . . . . . . . . . . . . . . . . . . . . 151 Temperature range Ambient temperature . . . . . . . . . . . . . . . . . . . . . . 23 173 Index Proline Prosonic Flow I 400 Modbus RS485 Ambient temperature range for display . . . . . . . . 163 Medium temperature . . . . . . . . . . . . . . . . . . . . . 161 Storage temperature . . . . . . . . . . . . . . . . . . . . . . . 18 Terminal assignment . . . . . . . . . . . . . . . . . . . 35, 37, 39 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Text editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Tool For mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Tool tip see Help text Tools Electrical connection . . . . . . . . . . . . . . . . . . . . . . 34 Totalizer Configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Transmitter Connecting the signal cables . . . . . . . . . . . . . . . . . 39 Turning the display module . . . . . . . . . . . . . . . . . 32 Transporting the measuring device . . . . . . . . . . . . . . 18 Troubleshooting General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Turning the display module . . . . . . . . . . . . . . . . . . . . 32 U UKCA marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Use of measuring device Borderline cases . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Incorrect use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 see Intended use User roles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 V Version data for the device . . . . . . . . . . . . . . . . . . . . 68 W Weight Transport (notes) . . . . . . . . . . . . . . . . . . . . . . . . . 18 Wizard Current output 1 . . . . . . . . . . . . . . . . . . . . . . . . . 89 Define access code . . . . . . . . . . . . . . . . . . . . . . . 111 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Double pulse output . . . . . . . . . . . . . . . . . . . . . . . 98 Low flow cut off . . . . . . . . . . . . . . . . . . . . . . . . . 101 Measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Pulse/frequency/switch output . . . . . . . . . . . . . . . 90 Pulse/frequency/switch output 1 to n . . . . 92, 93, 94 Relay output 1 to n . . . . . . . . . . . . . . . . . . . . . . . . 96 WLAN settings . . . . . . . . . . . . . . . . . . . . . . . . . . 108 WLAN settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Write protection Via access code . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Via write protection switch . . . . . . . . . . . . . . . . . 116 Write protection switch . . . . . . . . . . . . . . . . . . . . . . 116 174 Endress+Hauser *71645358* 71645358 www.addresses.endress.com ">

Public link updated
The public link to your chat has been updated.
Advertisement