Advantech PCI-1730 User manual

User Manual
PCI-1730/1733/1734
32-ch Isolated Digital I/O
PCI Cards
Copyright
The documentation and the software included with this product are copyrighted 2008
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Edition 2
Printed in Taiwan
PCI-1730/1733/1734 User Manual
September 2010
ii
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
CE
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
iii
PCI-1730/1733/1734 User Manual
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's
instructions.
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advantech.com
Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
Never pour any liquid into an opening. This may cause fire or electrical shock.
Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
PCI-1730/1733/1734 User Manual
iv
18. The equipment does not work well, or you cannot get it to work according to the
user's manual.
19. The equipment has been dropped and damaged.
20. The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
23. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
Safety Precaution - Static Electricity
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained
herein.Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
„ To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
„ Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive electronic components.
v
PCI-1730/1733/1734 User Manual
PCI-1730/1733/1734 User Manual
vi
Contents
Chapter
Chapter
1
Overview...............................................1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Introduction ............................................................................................... 2
Features .................................................................................................... 2
Applications............................................................................................... 4
Installation Guide ...................................................................................... 4
Software Overview .................................................................................... 5
Device Driver Programming Roadmap ..................................................... 5
Accessories............................................................................................... 7
2
Hardware Installation ..........................9
2.1
2.2
2.3
Installation ............................................................................................... 10
Unpacking ............................................................................................... 10
Driver Installation .................................................................................... 11
Figure 2.1 Advantech Automation Software Setup Screen ....... 11
Figure 2.2 Different Options for Driver Installation..................... 12
Hardware Installation .............................................................................. 12
Figure 2.3 Device Manager ....................................................... 13
Device Setup & Configuration ................................................................. 14
Figure 2.4 Device Manager Dialog Box ..................................... 14
Figure 2.5 “Device Found” Dialog Box....................................... 14
Figure 2.6 Device Setting Dialog Box ........................................ 15
Figure 2.7 The List of Devices Box............................................ 15
2.4
2.5
Chapter
3
Signal Connections ...........................17
3.1
3.2
Overview ................................................................................................. 18
Switch and Jumper Settings.................................................................... 18
Figure 3.1 Card Connector, Jumper and Switches.................... 18
Table 3.1: Summary of Jumper Settings ................................... 18
Table 3.2: Board ID setting (SW1)............................................. 19
Figure 3.2 Card Connector, Jumpers and Switches .................. 19
Table 3.3: Board ID setting (SW1)............................................. 20
Figure 3.3 Card Connector, Jumpers and Switches .................. 20
Table 3.4: Board ID setting (SW1)............................................. 21
Signal Connections ................................................................................. 21
Figure 3.4 TTL-level DI/O Connection ....................................... 24
Figure 3.5 Open/Short Connection ............................................ 24
Figure 3.6 Isolated DI Connection ............................................. 25
Figure 3.7 Isolated Digital Output Connection ........................... 25
Figure 3.8 Isolated Digital Input Connection.............................. 26
Figure 3.9 Isolated Digital Output Connection ........................... 28
3.3
Appendix A
Specifications ....................................29
A.1
Specifications .......................................................................................... 30
A.1.1 PCI-1730..................................................................................... 30
A.1.2 PCI-1733..................................................................................... 31
A.1.3 PCI-1734..................................................................................... 32
Appendix B
Block Diagram ...................................33
vii
PCI-1730/1733/1734 User Manual
B.1
B.2
B.3
PCI-1730................................................................................................. 34
PCI-1733................................................................................................. 35
PCI-1734................................................................................................. 36
Appendix C
Register Structure & Format............ 37
C.1
C.2
C.3
C.4
C.5
C.6
C.7
C.8
Overview ................................................................................................. 38
I/O Port Address Map ............................................................................ 38
Isolated Digital Input Registers ............................................................... 40
Isolated Digital Output Register .............................................................. 41
Non-isolated Digital Input Registers........................................................ 41
Non-isolated Digital Output Register....................................................... 42
Board ID — BASE+4H ........................................................................... 42
Interrupt Status Register ......................................................................... 43
PCI-1730/1733/1734 User Manual
viii
Chapter
1
Overview
1
1.1 Introduction
Thank you for buying the Advantech PCI-1730/1733/1734. The Advantech PCI-1730/
1733/1734 is a 32-channel isolated digital input/output card for the PCI bus.
For easy monitoring, each isolated digital input channel is equipped with one red
LED, and each isolated digital output channel is equipped with one green LED to
show its ON/OFF status. The PCI-1730 and PCI-1733’s isolated digital input channels are ideal for digital input in noisy environments or with floating potentials.
The PCI-1730/1733/1734 provides specific functions for different user requirements:
„ PCI-1730: 32-ch Isolated Digital I/O Card
„ PCI-1733: 32-ch Isolated Digital Input Card
„ PCI-1734: 32-ch Isolated Digital Output Card
The following sections of this chapter will provide further information about features,
installation guide, together with some brief information on software and accessories
for the PCI-1730/1733/1734 card.
1.2 Features
PCI-1730
„ Compatible as PCL-730
„ 32 isolated DIO channels (16 inputs and 16 outputs)
„ 32 TTL-level DIO channels (16 inputs and 16 outputs)
„ High output driving capacity
„ High-voltage isolation on isolated I/O channels (2,500 VDC)
„ Interrupt handling capability
„ 2 x 20-pin connectors for isolated DI/O channels and two for TTL DI/O channels
„ D-type connector for isolated input and output channels
„ High ESD protection (2,000 VDC)
„ High over-voltage protection (70 VDC)
„ Wide input range (5 ~ 30 VDC)
„ Board ID
PCI-1733
„ Compatible as PCL-733
„ 32 isolated Digital Input channels
„ High output driving capacity
„ High-voltage isolation on isolated Input channels (2,500 VDC)
„ Interrupt handling capability
„ D-type connector for isolated input channels
„ High ESD protection (2,000 VDC)
„ High over-voltage protection (70 VDC)
„ Wide input range (5 ~ 30 VDC)
„ Board ID
PCI-1730/1733/1734 User Manual
2
Fully Compatible with ISA-bus Products
All the specifications, connectors, pin-assignments, registries format are the same.
Users can upgrade their system to PCI bus without changing any existing wiring.
For Existing Windows Application Programs:
Users just need to remove the PCL-730/733/734 via the 'Device Manager', then
install the PCI-1730/1733/1734 instead (the device number must be the same). After
that, the user's original windows application program can work with PCI-1730/1733/
1734 properly.
For Existing DOS Application Programs:
Users just need to add some statements (to get the PCI bus PCI-1730/1733/1734
card's address and IRQ information) from our PCI-1730/1733/1734 DOS example
program into their original DOS application program. After that, user's original DOS
application program can work with PCI-1730/1733/1734 properly.
Robust Protection
The PCI-1730/1733 digital input channels feature robust isolation protection for
industrial, lab and machinery automation applications. It durably withstands voltage
up to 2,500 VDC, preventing your host system from any incidental harm. If connected
to an external input source with surge-protection, the PCI-1730/1733/1734 can offer
up to a maximum of 2,000 VDC ESD (Electrostatic Discharge) protection. Even with
an input voltage rising up to 70 VDC, the PCI-1730/1733 can still manage to work
properly, albeit only for a short period of time.
Wide Input Range
The PCI-1730/1733 has a wide range of input voltage from 5 to 30 VDC, and is suitable for most industrial applications with 12 VDC or 24 VDC input voltage.
Plug-and-Play Function
The PCI-1730/1733/1734 is a Plug-and-Play device, which fully complies with PCI
Specification Rev 2.2. During card installation, there is no need to set jumpers or DIP
switches. Instead, all bus-related configurations such as base I/O address and interrupt are automatically done by the Plug-and-Play function.
3
PCI-1730/1733/1734 User Manual
Overview
The Advantech PCI-1730/1733/1734 offers the following main features:
Chapter 1
PCI-1734
„ Compatible as PCL-734
„ 32 isolated Digital Output channels
„ High output driving capacity
„ High-voltage isolation on isolated Output channels (2,500 VDC)
„ D-type connector for isolated input and output channels
„ High ESD protection (2,000 VDC)
„ Board ID
Board ID
The PCI-1730/1733/1734 has a built-in DIP Switch that helps define each card’s ID
when multiple PCI-1730/1733/1734 cards have been installed on the same PC chassis. The board ID setting function is very useful when users build their system with
multiple PCI-1730/1733/1734 cards. With correct Board ID settings, you can easily
identify and access each card during hardware configuration and software programming.
Note:
--For detailed specifications of the PCI-1730/1733/1734, please refer to Appendix A,
Specifications.
1.3 Applications
„
„
„
„
„
„
Industrial ON/OFF control
Switch status sensing
BCD interfacing
Digital I/O control
Industrial and lab automation
Laboratory & Education
1.4 Installation Guide
Before you install your PCI-1730/1733/1734 card, please make sure you have the following necessary components:
„ PCI-1730/1733/1734 card
„ PCI-1730/1733/1734 User’s Manual
„ Driver software Advantech DLL drivers
(Included in the companion CD-ROM)
„ Wiring cable PCL-10137 (option)
„ Wiring board PCLD-880, ADAM-3937 (option)
„ Computer Personal computer or workstation with a PCI-bus slot
Some other optional components are also available for enhanced operation:
„
Application software: ActiveDAQ, GeniDAQ or third-party software packages
After you get the necessary components and maybe some of the accessories for
enhanced operation of your Multifunction card, you can then begin the Installation
procedures. Figure 1-1 on the next page provides a concise flow chart to give users a
broad picture of the software and hardware installation procedures:
PCI-1730/1733/1734 User Manual
4
Advantech offers a rich set of DLL drivers, third-party driver support and application
software to help fully exploit the functions of your PCI-1730/1733/1734 card:
Programming choices for DA&C cards: You may use Advantech application software
such as Advantech Device Drivers. On the other hand, advanced users are allowed
another option for register-level programming, although not recommended due to its
laborious and time-consuming nature.
Device Drivers
The Advantech Device Drivers software is included on the companion CD-ROM at no
extra charge. It also comes with all the Advantech DA&C cards. Advantech’s DLL
driver features a complete I/O function library to help boost your application performance. The Advantech Device Drivers for Windows 2000/95/98/ME/NT/XP works
seamlessly with development tools such as Visual C++, Visual Basic, Inprise C++
Builder and Inprise Delphi.
Register-level Programming
Register-level programming is reserved for experienced programmers who find it
necessary to write code directly at the level of device registers. Since register-level
programming requires much effort and time, we recommend that you use the Advantech Device Drivers instead. However, if register-level programming is indispensable,
you should refer to the relevant information in Appendix C, Register Structure and
Format, or to the example code included on the companion CD-ROM.
1.6 Device Driver Programming Roadmap
This section will provide you a roadmap to demonstrate how to build an application
from scratch using Advantech Device Drivers with your favorite development tools
such as Visual C++, Visual Basic, Delphi and C++ Builder. The step-by-step instructions on how to build your own applications using each development tool will be given
in the Device Drivers Manual. Moreover, a rich set of example source codes are also
given for your reference.
Programming Tools
Programmers can develop application programs with their development tools:
„ Visual C++
„ Visual Basic
„ Delphi
„ C++ Builder
5
PCI-1730/1733/1734 User Manual
Overview
Device Drivers (on the companion CD-ROM)
LabVIEW driver
Advantech ActiveDAQ
Advantech GeniDAQ
Chapter 1
1.5 Software Overview
For instructions on how to begin programming works in each development tool,
Advantech offers a Tutorial Chapter in the Device Drivers Manual for your reference.
Please refer to the corresponding sections in this chapter on the Device Drivers Manual to begin your programming efforts. You can also look at the example source
codes provided for each programming tool, since they can help you get familiar
quickly.
The Device Drivers Manual can be found on the companion CD-ROM. Or if you have
already installed the Device Drivers on your system, The Device Drivers Manual can
be readily accessed through the Start button:
Start/Programs/Advantech Device Driver V1.5/Device Driver Manual
The example source codes could be found under the corresponding installation
folder such as the default installation path:
\Program Files\Advantech\ADSAPI\Examples
For information about using other function groups or other development tools, please
refer to the Creating Windows 95/NT/2000 Application with Device Driver chapter
and the Function Overview chapter on the Device Drivers Manual.
Programming with Device Drivers Function Library
Advantech Device Drivers offers a rich function library to be utilized in various application programs. This function library consists of numerous APIs that support many
development tools, such as Visual C++, Visual Basic, Delphi and C++ Builder.
According to their specific functions or services, those APIs can be categorized into
several function groups:
„ Digital Input/Output Function Group
„ Port Function Group (direct I/O)
„ Event Function Group
For the usage and parameters of each function, please refer to the Function Overview chapter in the Device Drivers Manual.
Troubleshooting Device Driver Error
Driver functions will return a status code when they are called to perform a certain
task for the application. When a function returns a code that is not zero, it means the
function has failed to perform its designated function. To troubleshoot the Device
Drivers error, you can pass the error code to DRV_GetErrorMessage function to
return the error message. Or you can refer to the Device Drivers Error Codes Appendix in the Device Drivers Manual for a detailed listing of the Error Code, Error ID and
the Error Message.
PCI-1730/1733/1734 User Manual
6
Advantech offers a complete set of accessory products to support the PCI-1730/
1733/1734 card. These accessories include:
Wiring Boards
The ADAM-3937 is a 37-pin D-type wiring terminal module for DIN-rail mounting.
This terminal module can be readily connected to the Advantech PC-Lab cards and
allow easy yet reliable access to individual pin connections for the PCI-1730/1733/
1734 card.
The PCLD-880 is a universal screw-terminal board to be used with any of the PCLabCards which have 37-pin D-type connectors.
All the specifications, connectors, pin-assignments, registries format are the same.
Users can upgrade their system into PCI bus without change any existed wiring system.
7
PCI-1730/1733/1734 User Manual
Overview
Wiring Cable
The PCL-10137 shielded cable is specially designed for PCI-1730/1733/1734 cards
to provide high resistance to noise. To achieve better signal quality, the signal wires
are twisted in such a way as to form a “twisted-pair cable”, reducing cross-talk and
noise from other signal sources. Furthermore, its analog and digital lines are separately sheathed and shielded to neutralize EMI/EMC problems.
Chapter 1
1.7 Accessories
PCI-1730/1733/1734 User Manual
8
Chapter
2
2
Hardware Installation
2.1 Installation
This chapter gives users a package item checklist, proper instructions about unpacking and step-by-step procedures for both driver and card installation.
2.2 Unpacking
After receiving your PCI-1730/1733/1734 package, please inspect its contents first.
The package should contain the following items:
„ PCI-1730/1733/1734 card
„ Companion CD-ROM (Device Drivers included)
„ User’s Manual
The PCI-1730/1733/1734 card harbors certain electronic components vulnerable to
electrostatic discharge (ESD). ESD could easily damage the integrated circuits and
certain components if preventive measures are not carefully paid attention to.
Before removing the card from the antistatic plastic bag, you should take following
precautions to ward off possible ESD damage:
„ Touch the metal part of your computer chassis with your hand to discharge static
electricity accumulated on your body. Or one can also use a grounding strap.
„ Touch the anti-static bag to a metal part of your computer chassis before opening the bag.
„ Take hold of the card only by the metal bracket when removing it out of the bag.
After taking out the card, first you should:
Inspect the card for any possible signs of external damage (loose or damaged components, etc.). If the card is visibly damaged, please notify our service department or
our local sales representative immediately. Avoid installing a damaged card into your
system.
Also pay extra caution to the following aspects to ensure proper installation:
„ Avoid physical contact with materials that could hold static electricity such as
plastic, vinyl and Styrofoam.
„ Whenever you handle the card, grasp it only by its edges. DO NOT TOUCH the
exposed metal pins of the connector or the electronic components.
Note!
Keep the anti-static bag for future use. You might need the original bag
to store the card if you have to remove the card from PC or transport it
elsewhere.
PCI-1730/1733/1734 User Manual
10
We recommend you to install the driver before you install the PCI-1730/1733/1734
card into your system, since this will guarantee a smooth installation process.
The Advantech Device Driver Setup program for the PCI-1730/1733/ 1734 card is
included on the companion CD-ROM that is shipped with your DA&C card package.
Please follow the steps below to install the driver software:
Insert the companion CD-ROM into your CD-ROM drive.
The Setup program will be launched automatically if you have the autoplay function enabled on your system. When the Setup Program is launched, you’ll see
the following Setup Screen.
Note!
If the autoplay function is not enabled on your computer, use Windows
Explorer or Windows Run command to execute SETUP.EXE on the
companion CD-ROM.
Figure 2.1 Advantech Automation Software Setup Screen
3.
4.
Select the Individual Drivers option.
Select the specific device then just follow the installation instructions step by
step to complete your device driver installation and setup.
11
PCI-1730/1733/1734 User Manual
Hardware Installation
1.
2.
Chapter 2
2.3 Driver Installation
Figure 2.2 Different Options for Driver Installation
For further information on driver-related issues, an online version of Device Drivers
Manual is available by accessing the following path:
Start/Programs/Advantech Device Drivers V1.5/ Device Drivers Manual
2.4 Hardware Installation
Note!
Make sure you have installed the driver first before you install the card
(please refer to 2.2 Driver Installation)
After the device driver installation is completed, you can now go on to install the PCI1730/1733/1734 card in any PCI slot on your computer. But it is suggested that you
should refer to the computer user manual or related documentation if you have any
doubt. Please follow the steps below to install the card on your system.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Turn off your computer and unplug the power cord and cables. TURN OFF your
computer before installing or removing any components on the computer.
Remove the cover of your computer.
Remove the slot cover on the back panel of your computer.
Touch the metal part on the surface of your computer to neutralize the static
electricity that might be on your body.
Insert the PCI-1730/1733/1734 card into a PCI slot. Hold the card only by its
edges and carefully align it with the slot. Insert the card firmly into place. Use of
excessive force must be avoided, otherwise the card might be damaged.
Fasten the bracket of the PCI card on the back panel of the computer.
Connect appropriate accessories to the PCI card.
Replace the cover of your computer chassis. Re-connect the cables you
removed in step 2.
Plug in the power cord and turn on the computer.
PCI-1730/1733/1734 User Manual
12
In case you installed the card without installing the Device Drivers first,
Win95/98/ME will recognize your card as an “unknown device” after
rebooting, and will prompt you to provide the necessary driver. Ignore
the prompting messages (just click the Cancel button) and set up the
driver according to the steps described in 2.2 Driver Installation.
1. Access the Device Manager through Control Panel/System/Device Manager.
2. The device name of the PCI-1730/1733/1734 should be listed on the Device Manager tab on the System Property Page.
Figure 2.3 Device Manager
Note!
If your card is properly installed, you should see the device name of your
card listed on the Device Manager tab. If you do see your device name
listed on it but marked with an exclamation sign “!”, it means your card
has not been correctly installed. In this case, remove the card device
from the Device Manager by selecting its device name and press the
Remove button. Then go through the driver installation process again.
After your card is properly installed on your system, you can now configure your
device using the Device Installation Program that has itself already been installed on
your system during driver setup. A complete device installation procedure should
include device setup, configuration and testing. The following sections will guide you
through the Setup, Configuration and Testing of your device.
13
PCI-1730/1733/1734 User Manual
Hardware Installation
After the PCI-1730/1733/1734 card is installed, you can verify whether it is properly
installed on your system in the Device Manager:
Chapter 2
Note!
2.5 Device Setup & Configuration
The Advantech Device Manager program is a utility that allows you to set up, configure and test your device, and later stores your settings on the system registry. These
settings will be used when you call the APIs of Advantech Device Drivers.
Setting Up the Device
1. To install the I/O device for your card, you must first run the Device Manager
program (by accessing Start/Programs/ Advantech Device Drivers V1.5).
2. You can then view the device(s) already installed on your system (if any) on the
Installed Devices list box. Since you haven’t installed any device yet, you might
see a blank list such as the one below (Fig. 2-4).
Figure 2.4 Device Manager Dialog Box
3.
Scroll down the Supported of Devices box to find the device that you wish to
install, then click the Add… button to evoke the Existing unconfigured PCI-1730
dialog box such as one shown in Fig. 2-5. The Existing unconfigured PCI-1730
dialog box lists all the installed devices on your system. Select the device you
want to configure from the list box and press the OK button. After you have
clicked OK, you will see a PCI-1730 Device Setting dialog box such as the one
in Fig. 2-6.
Figure 2.5 “Device Found” Dialog Box
PCI-1730/1733/1734 User Manual
14
5.
After you have finished configuring the device, click OK and the device name
will appear in the Installed Devices box as seen below:
Figure 2.7 The List of Devices Box
Note!
As we have noted, the device name “000:<PCI-1730 BoardID=0 I/
O=1000H>” begins with a device number “000”, which is specifically
assigned to each card. The device number is passed to the driver to
specify which device you wish to control.
After your card is properly installed and configured, you can click the Test… button to
test your hardware by using the testing utility we supplied. For more detailed information, please refer to Chapter 2 of the Device Drivers Manual.
You can also find the rich examples on the CD-ROM to speeding up your programming.
15
PCI-1730/1733/1734 User Manual
Hardware Installation
Figure 2.6 Device Setting Dialog Box
Chapter 2
Configuring the Device
4. On the PCI-1730 Device Setting dialog box (Fig. 2-6), you can configure the
IDI00, IDI01 and DI00, DI01 Interrupt trigger mode either as Rising Edge or Falling Edge, and Enable or Disable the IDI00, IDI01 and DI00, DI01.
PCI-1730/1733/1734 User Manual
16
Chapter
3
3
Signal Connections
3.1 Overview
Maintaining signal connections is one of the most important factors in ensuring that
your application system is sending and receiving data correctly. A good signal connection can avoid unnecessary and costly damage to your PC and other hardware
devices. This chapter provides useful information about how to connect input and
output signals to the PCI-1730/1733/1734 via the I/O connector.
3.2 Switch and Jumper Settings
PCI-1730
The PCI-1730 card has two function jumper settings.
Figure 3.1 Card Connector, Jumper and Switches
Table 3.1: Summary of Jumper Settings
Names of Jumpers
JP4, JP5
Function description
A1 version
B2 version
PCI-1730/1733/1734 User Manual
18
Chapter 3
Table 3.2: Board ID setting (SW1)
ID2
ID1
ID0
Board ID
1
1
1
1
0
1
1
1
0
1
1
1
0
1
2
1
1
0
0
3
1
0
1
1
4
1
0
1
0
5
1
0
0
1
6
1
0
0
0
7
0
1
1
1
8
0
1
1
0
9
0
1
0
1
10
0
1
0
0
11
0
0
1
1
12
0
0
1
0
13
0
0
0
1
14
0
0
0
0
15
Signal Connections
ID3
Note: On: 1, Off: 0
PCI-1733
Figure 3.2 Card Connector, Jumpers and Switches
19
PCI-1730/1733/1734 User Manual
Table 3.3: Board ID setting (SW1)
ID3
ID2
ID1
ID0
Board ID
1
1
1
1
0
1
1
1
0
1
1
1
0
1
2
1
1
0
0
3
1
0
1
1
4
1
0
1
0
5
1
0
0
1
6
1
0
0
0
7
0
1
1
1
8
0
1
1
0
9
0
1
0
1
10
0
1
0
0
11
0
0
1
1
12
0
0
1
0
13
0
0
0
1
14
0
0
0
0
15
Note: On: 1, Off: 0
PCI-1734
The PCI-1734 card has one function jumper setting.
Figure 3.3 Card Connector, Jumpers and Switches
PCI-1730/1733/1734 User Manual
20
Chapter 3
Table 3.4: Board ID setting (SW1)
ID2
ID1
ID0
Board ID
1
1
1
1
0
1
1
1
0
1
1
1
0
1
2
1
1
0
0
3
1
0
1
1
4
1
0
1
0
5
1
0
0
1
6
1
0
0
0
7
0
1
1
1
8
0
1
1
0
9
0
1
0
1
10
0
1
0
0
11
0
0
1
1
12
0
0
1
0
13
0
0
0
1
14
0
0
0
0
15
Signal Connections
ID3
Note: On: 1, Off: 0
3.3 Signal Connections
PCI-1730 (JP4, JP5: REV.A1) Pin Assignments
CN1
IDO 0
IDO 2
IDO 4
IDO 6
IDO 8
IDO
IDO
IDO
EGN
EGN
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
CN2
IDO 1
IDO 3
IDO 5
IDO 7
IDO 9
IDO 11
IDO 13
IDO 15
EGND
PCOM
IDI 0
IDI 2
IDI 4
IDI 6
IDI 8
IDI 10
IDI 12
IDI 14
ECOM
ECOM
1
3
5
7
9
11
13
15
17
19
CN3
DO 0
DO 2
DO 4
DO 6
DO 8
DO
DO
DO
GND
+5 V
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
2
4
6
8
10
12
14
16
18
20
IDI 1
IDI 3
IDI 5
IDI 7
IDI 9
IDI 11
IDI 13
IDI 15
ECOM
ECOM
CN4
DO 1
DO 3
DO 5
DO 7
DO 9
DO 11
DO 13
DO 15
GND
+12 V
DI 0
DI 2
DI 4
DI 6
DI 8
DI 10
DI 12
DI 14
GND
+5 V
21
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
DI 1
DI 3
DI 5
DI 7
DI 9
DI 11
DI 13
DI 15
GND
+12 V
PCI-1730/1733/1734 User Manual
CN5
EGN
1
2
EGND
CN6
Description of pin use:
IDIn (n=0 ~ 15):
Isolated digital input
IDOn (n=0 ~ 15):
Isolated digital output
ECOM:
External common Vcc/GND of IDI
PCOM:
Free wheeling common diode for
EGND:
External ground for IDO
DIn (n=0 ~ 15):
Digital input
DOn (n=0 ~ 15):
Digital output
GND:
Digital ground
IDI 0
IDI 2
IDI 4
IDI 6
IDI 8
IDI 10
IDI 12
IDI 14
ECOM
EGND
IDO 0
IDO 2
IDO 4
IDO 6
IDO 8
IDO 10
IDO 12
IDO 14
PCOM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
IDI 1
IDI 3
IDI 5
IDI 7
IDI 9
IDI 11
IDI 13
IDI 15
EGND
EGND
IDO 1
IDO 3
IDO 5
IDO 7
IDO 9
IDO 11
IDO 13
IDO 15
.
Note: ECOM and PCOM are totally different. User must connect them carefully!
PCI-1730 (JP4, JP5: REV.B2) Pin Assignments
CN1
IDO 0
IDO 2
IDO 4
IDO 6
IDO 8
IDO
IDO
IDO
EGN
PCO
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
CN2
IDO 1
IDO 3
IDO 5
IDO 7
IDO 9
IDO 11
IDO 13
IDO 15
EGND
PCOM1
PCI-1730/1733/1734 User Manual
IDI 0
IDI 2
IDI 4
IDI 6
IDI 8
IDI 10
IDI 12
IDI 14
ECOM
ECOM
22
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
IDI 1
IDI 3
IDI 5
IDI 7
IDI 9
IDI 11
IDI 13
IDI 15
ECOM
ECOM
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
DO 1
DO 3
DO 5
DO 7
DO 9
DO 11
DO 13
DO 15
GND
+12 V
DI 0
DI 2
DI 4
DI 6
DI 8
DI 10
DI 12
DI 14
GND
+5 V
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
DI 1
DI 3
DI 5
DI 7
DI 9
DI 11
DI 13
DI 15
GND
+12 V
CN5
EGN
1
2
EGND
CN6
Description of pin use:
IDIn (n=0 ~ 15):
Isolated digital input
IDOn (n=0 ~ 15):
Isolated digital output
ECOMn (n=0 ~ 1):
External common Vcc/GND of IDI
PCOMn (n=0 ~ 1):
Free wheeling common diode for
EGND:
External ground for IDO
DIn (n=0 ~ 15):
Digital input
DOn (n=0 ~ 15):
Digital output
GND:
Digital ground
IDI 0
IDI 2
IDI 4
IDI 6
IDI 8
IDI 10
IDI 12
IDI 14
ECOM
PCOM
IDO 0
IDO 2
IDO 4
IDO 6
IDO 8
IDO 10
IDO 12
IDO 14
PCOM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
IDI 1
IDI 3
IDI 5
IDI 7
IDI 9
IDI 11
IDI 13
IDI 15
ECOM
EGND
IDO 1
IDO 3
IDO 5
IDO 7
IDO 9
IDO 11
IDO 13
IDO 15
.
Note: ECOMn and PCOMn are totally different. User must be connect them carefully!
23
PCI-1730/1733/1734 User Manual
Signal Connections
DO 0
DO 2
DO 4
DO 6
DO 8
DO
DO
DO
GND
+5 V
CN4
Chapter 3
CN3
TTL-level Digital Input/Output
The PCI-1730 has 16 TTL-level digital inputs and 16 TTL-level digital
outputs. The following figure shows connections to exchange digital
signals with other TTL devices:
PCI-1730
TTL device
DO
DI
GND
Figure 3.4 TTL-level DI/O Connection
If you want to receive an OPEN/SHORT signal from a switch or relay, add a pull-up
resistor to ensure that the input is held at a high level when the contacts are open.
See the figure below:
+5V
PCI-1730
4.7K
DI
Switch
GND
Figure 3.5 Open/Short Connection
PCI-1730/1733/1734 User Manual
24
External
Internal
Signal Connections
IDI0
Wet
contact
ECOM
Isolated
Circuit
IDI1
Dry
Contact
EGND
Figure 3.6 Isolated DI Connection
Isolated Digital Output
Each of the 16 isolated DO channels come equipped with a darlington transistor.
Every eight ouput channels share common emitters and integral suppression diodes
for inductive load, activated by connecting PCOM to VDD. If the external voltage
source (5~40 V) is connected to each isolated output channel (IDO) and its isolated
digital output turns on (200 mA max./ch), the card's current will sink from the external
voltage source. The current through EGND should not exceed 2.4 A. If the current for
all channels combined exceeds 2 A, CN5 must be connected to the external ground
to share the extra current. The following figure shows how to connect an external output load to the card's isolated outputs.
Internal
External
Diode
PCOM
Common
IDO0
NC
NO
IDO1
Isolated
Circuit
IDO2
IDO3
IDO4
IDO5
IDO6
Relay
VDD
5~40V
IDO7
EGND
Figure 3.7 Isolated Digital Output Connection
25
Chapter 3
Isolated Digital Input
Each of the 16 isolated digital input channels accept voltages from 5 to 30 V. Every
eight input channels share one external common. (Channels 0 ~ 7 use ECOM0.
Channels 8 ~ 15 use ECOM1.) The following figure shows how to connect an external input source to the card's isolated inputs.
PCI-1730/1733/1734 User Manual
PCI-1733 Pin Assignments
CN1
Description of pin use:
IDIn (n=0 ~ 31):
Isolated digital input
ECOM n (n=0 ~ 3):
External common Vcc/GND of IDI
EGND:
External ground for IDI
IDI 0
IDI 2
IDI 4
IDI 6
ECOM
IDI 9
IDI 11
IDI 13
IDI 15
IDI 16
IDI 18
IDI 20
IDI 22
ECOM
IDI25
IDI27
IDI29
IDI31
EGND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
IDI 1
IDI 3
IDI 5
IDI 7
IDI 8
IDI 10
IDI 12
IDI 14
ECOM
IDI17
IDI19
IDI21
IDI23
IDI24
IDI26
IDI28
IDI30
ECOM
.
Isolated Digital Input
Each of the 32 isolated digital input channels accept voltages from 5
to 30 V. Every eight input channels share one external common. (Channels 0 ~ 7 use
ECOM0. Channels 8 ~ 15 use ECOM1. Channels 16 ~ 23 use ECOM2. Channels 24
~ 31 use ECOM3.) The following figure shows how to connect an external input
source to the card's isolated inputs.
External
Internal
IDI0
Wet
contact
ECOM
Isolated
Circuit
IDI1
Dry
Contact
EGND
Figure 3.8 Isolated Digital Input Connection
PCI-1730/1733/1734 User Manual
26
CN1
Description of pin use:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
IDO 1
IDO 3
IDO 5
IDO 7
IDO 8
IDO 10
IDO 12
IDO 14
PCOM
IDO17
IDO19
IDO21
IDO23
IDO24
IDO26
IDO28
IDO30
PCOM
.
27
PCI-1730/1733/1734 User Manual
Signal Connections
IDOn (n=0 ~ 31):
Isolated digital output
PCOM n (n=0 ~ 3):
Free wheeling common diode for
EGND:
External ground for IDO
IDO 0
IDO 2
IDO 4
IDO 6
PCOM
IDO 9
IDO 11
IDO 13
IDO 15
IDO 16
IDO 18
IDO 20
IDO 22
PCOM
IDO25
IDO27
IDO29
IDO31
EGND
Chapter 3
PCI-1734 Pin Assignments
Isolated Digital Output
Each of the 32 isolated digital output channels comes equipped with a darlington
transistor. Every eight ouput channels share common emitters and integral suppression diodes for inductive load, activated by connecting PCOM to VDD. (Channels 0 ~
7 use PCOM0. Channels 8 ~ 15 use PCOM1. Channels 16 ~ 23 use PCOM2. If the
external voltage source (5~40 V) is connected to each isolated output channel (IDO)
and its isolated digital output turns on (200 mA max./ch), the card's current will sink
from the external voltage source. The current through EGND should not exceed 4.8
A. If the current for all channels combined exceeds 2 A, CN2 must be connected to
the external ground to share the extra current. The following figure shows how to
connect an external output load to the card's isolated outputs.
Internal
External
Diode
PCOM
Common
IDO0
NC
NO
IDO1
Isolated
Circuit
IDO2
IDO3
IDO4
IDO5
IDO6
Relay
VDD
5~40V
IDO7
EGND
Figure 3.9 Isolated Digital Output Connection
PCI-1730/1733/1734 User Manual
28
Appendix
A
Specifications
A
A.1 Specifications
A.1.1 PCI-1730
Isolated Digital Input
Number of Channel
16 (bi-directional)
Optical Isolation
2,500 VDC
Opto-isolator response time
25μs
Over-voltage Protect
70 VDC
Input Voltage
VIH (max.)
30 VDC
VIH (min.)
5 VDC
VIL (max.)
2 VDC
5 VDC
1.4 mA (typical)
12 VDC
3.9 mA (typical)
24 VDC
8.2 mA (typical)
30 VDC
10.3 mA (typical)
Input Current
Isolated Digital Output
Number of Channel
16
Optical Isolation
2,500 VDC
Output Voltage
Open collector 5 to 40 VDC
Sink/Source Current
200 mA max./ch
150 mA max./ch for all channel using
Non-isolated Digital Input/Output
Input Channels
16
Input Voltage
Low
0.8 V max.
High
2.0 V min.
Output Channels
16
Output Voltage
Low
0.5 V max. @ +24 mA (sink)
High
2.4 V min. @ -15 mA (source)
General
I/O Connector Type
37-pin D-Sub female
Dimensions
175 mm x 100 mm (6.9" x 3.9")
Power Consumption
Typical
+5 V @ 250 mA
+12 V @ 35 mA
Max.
+5 V @ 400 mA
Operation
0~+60°C (32~140°F)
(refer to IEC 68-2-1,2)
Storage
-20~+85°C (-4~185°F)
Temperature
Relative Humidity
5~95%RH non-condensing
(refer to IEC 68-2-3)
Certification
CE certified
PCI-1730/1733/1734 User Manual
30
Isolated Digital Input
Number of Channel
32 (bi-directional)
Optical Isolation
2,500 VDC
Opto-isolator response time
25μs
Over-voltage Protect
70 VDC
Input Voltage
VIH (max.)
30 VDC
VIH (min.)
5 VDC
VIL (max.)
2 VDC
5 VDC
1.4 mA (typical)
12 VDC
3.9 mA (typical)
24 VDC
8.2 mA (typical)
30 VDC
10.3 mA (typical)
Input Current
General
I/O Connector Type
37-pin D-Sub female
Dimensions
175 mm x 100 mm (6.9" x 3.9")
Power Consumption
Typical
+5 V @ 200 mA
+12 V @ 50 mA
Max.
+5 V @ 350 mA
Operation
0~+60°C (32~140°F)
(refer to IEC 68-2-1,2)
Storage
-20~+85°C (-4~185°F)
Temperature
Relative Humidity
5~95%RH non-condensing
(refer to IEC 68-2-3)
Certification
CE certified
31
PCI-1730/1733/1734 User Manual
Appendix A Specifications
A.1.2 PCI-1733
A.1.3 PCI-1734
Isolated Digital Output
Number of Channel
32
Optical Isolation
2,500 VDC
Output Voltage
Open collector 5 to 40 VDC
Sink/Source Current
200 mA max./ch
150 mA max./ch for all channel using
General
I/O Connector Type
37-pin D-Sub female
Dimensions
175 mm x 100 mm (6.9" x 3.9")
Power Consumption
Typical
+5 V @ 150 mA
+12 V @ 15 mA
Max.
+5 V @ 250 mA
Operation
0~+60°C (32~140°F)
(refer to IEC 68-2-1,2)
Storage
-20~+85°C (-4~185°F)
Temperature
Relative Humidity
5~95%RH non-condensing
(refer to IEC 68-2-3)
Certification
CE certified
PCI-1730/1733/1734 User Manual
32
Appendix
B
Block Diagram
B
B.1 PCI-1730
IDI0 ~ IDI7
Isolation
IDI8 ~ IDI15
Address Bus
IDO0 ~IDO7
D-Sub
37 Pin
Connector
IDO8 ~ IDO15
ECOM
PCOM
EGND
Control Bus
PCI
BUS
BoxHander
20 Pin*2
(IDI/O)
Control
Logic
DI0 ~ DI7
PLX
PCI 9052
DI8 ~ DI15
DO0 ~ DO7
DO8 ~ DO15
GND
Data Bus
+5V
+12V
Interrupt
Control
Logic
PCI-1730/1733/1734 User Manual
Isolation
34
DI0 ~ DI1
IDI0 ~ IDI1
BoxHander
20 Pin*2
(DI/O)
Address Bus
Control
Logic
Control Bus
Data Bus
PCI
BUS
PLX
PCI 9052
IDI0 ~ IDI7
IDI8 ~ IDI15
IDI16 ~IDI23
Isolation
IDI24 ~ IDI31
D-Sub
37 Pin
Connector
ECOM0 ~ ECOM3
EGND
Interrupt
Control
Logic
35
IDI0 ~ IDI1
IDI16 ~ IDI17
PCI-1730/1733/1734 User Manual
Appendix B Block Diagram
B.2 PCI-1733
B.3 PCI-1734
Address Bus
Control
Logic
Control Bus
Data Bus
PCI
BUS
PLX
PCI 9052
IDO0 ~ IDO7
IDO8 ~ IDO15
IDO16 ~IDO23
IDO24 ~ IDO31
PCOM0 ~ PCOM3
EGND
PCI-1730/1733/1734 User Manual
36
Isolation
D-Sub
37 Pin
Connector
Appendix
C
C
Register Structure &
Format
C.1 Overview
The most important consideration in programming the PCI-1730/1733/1734 at the
register level is to understand the function of the card's registers. The information in
the following sections is provided only for users who would like to do their own lowlevel programming.
C.2 I/O Port Address Map
The PCI-1730/1733/1734 requires 16 consecutive addresses in the PC's I/O space.
The address of each register is specified as an offset from the card's base address.
For example, BASE+0 is the card's base address and BASE+6 is the base address
plus six bytes. The table C-1 shows the function of each register of the PCI-1730/
1733/1734 or driver and its address relative to the card's base address.
Base Addr. 7
+HEX
0H
R
08H R
W
0CH R
W
10H R
W
IDI5
IDI4
IDI3
IDI2
IDI1
IDI0
IDO6
IDO5
IDO4
IDO3
IDO2
IDO1
IDO0
IDI14
IDI13
IDI12
IDI11
IDI10
IDI9
IDI8
IDO14
IDO13
IDO12
IDO11
IDO10
IDO9
IDO8
DI6
DI5
DI4
DI3
DI2
DI1
DI0
DO6
DO5
DO4
DO3
DO2
DO1
DO0
DI14
DI13
DI12
DI11
DI10
DI9
DI8
DO13
DO12
DO11
DO10
DO9
DO8
BD3
BD2
BD1
BD0
DI1EN
DI0EN
IDI1EN IDI0EN
DI1EN
DI0EN
IDI1EN IDI0EN
DI1RF
DI0RF
IDI1RF IDI0RF
DI1RF
DI0RF
IDI1RF IDI0RF
DI1F
DI0F
IDI1F
DI1CLR
DI0CLR IDI1CL IDI0CL
R
R
Digital Output
DO15
04H R
IDI6
Digital Input
DI15
W
0
Digital Output
DO7
03H R
1
Digital Input
DI7
W
2
Isolated Digital Output
IDO15
02H R
3
Isolated Digital Input
IDI15
W
4
Isolated Digital Output
IDO7
01H R
5
Isolated Digital Input
IDI7
W
6
DO14
Board ID Register
Interrupt Enable Status
Interrupt Enable Register
Interrupt Triggering Status
Interrupt Triggering Register
Interrupt Flag
IDI0F
Interrupt Clear Register
PCI-1730/1733/1734 User Manual
38
Base Addr. 7
+HEX
00H
R
R
Isolated Digital Input
08H
R
Isolated Digital Input
IDI22
IDI21
W
N/A
R
Isolated Digital Input
IDI30
W
N/A
R
Board ID Register
R
R
W
10H
IDI13
N/A
W
0CH
IDI14
W
IDI31
04H
IDI5
N/A
IDI23
03H
IDI6
W
IDI15
02H
5
R
W
4
3
2
1
0
IDI4
IDI3
IDI2
IDI1
IDI0
IDI12
IDI11
IDI10
IDI9
IDI8
IDI20
IDI19
IDI18
IDI17
IDI16
IDI28
IDI27
IDI26
IDI25
IDI24
BD3
BD2
BD1
BD0
IDI17EN
IDI16EN
IDI1EN
IDI0EN
IDI17EN
IDI16EN
IDI1EN
IDI0EN
IDI17RF
IDI16RF
IDI1RF
IDI0RF
IDI17RF
IDI16RF
IDI1RF
IDI0RF
IDI17F
IDI16F
IDI1F
IDI0F
Isolated Digital Input
IDI7
01H
6
IDI29
Interrupt Enable Status
Interrupt Enable Register
Interrupt Triggering Status
Interrupt Triggering Register
Interrupt Flag
Interrupt Clear Register
IDI17CLR IDI16CLR IDI1CLR IDI0CLR
39
PCI-1730/1733/1734 User Manual
Appendix C Register Structure & Format
Table C-2 PCI-1733 Register Format
Table C-3 PCI-1734 Register Format
Base Addr. 7
+HEX
0H
6
R
N/A
W
Isolated Digital Output
R
N/A
W
Isolated Digital Output
R
N/A
W
Isolated Digital Output
R
N/A
W
Isolated Digital Output
R
Board ID Register
IDO7
1H
IDO6
IDO15
2H
IDO23
3H
IDO31
4H
5
W
IDO14
IDO22
IDO30
IDO5
IDO13
IDO21
IDO29
4
3
2
1
0
IDO4
IDO3
IDO2
IDO1
IDO0
IDO12
IDO11
IDO10
IDO9
IDO8
IDO20
IDO19
IDO18
IDO17
IDO16
IDO28
IDO27
IDO26
IDO25
IDO24
BD3
BD2
BD1
BD0
N/A
C.3 Isolated Digital Input Registers
BASE+0H/1H (/2H/3H)
The PCI-1730 offers 16-ch isolated digital input channels. These channels use the
input ports at addresses BASE+0H/1H.
Table C-1 Register for Isolated Digital Input
Read
Isolated Digital Input
Bit #
7
6
5
4
3
2
1
0
BASE + 0H
IDI7
IDI6
IDI5
IDI4
IDI3
IDI2
IDI1
IDI0
BASE + 1H
IDI15
IDI14
IDI13
IDI12
IDI11
IDI10
IDI9
IDI8
The PCI-1733 offers 32-ch isolated digital input channels. These channels use the
input ports at addresses BASE+0H/1H/2H/3H.
Table C-2 Register for Isolated Digital Input
Read
Isolated Digital Input
Bit #
7
6
5
4
3
2
1
0
BASE + 0H
IDI7
IDI6
IDI5
IDI4
IDI3
IDI2
IDI1
IDI0
BASE + 1H
IDI15
IDI14
IDI13
IDI12
IDI11
IDI10
IDI9
IDI8
BASE + 2H
IDI23
IDI22
IDI21
IDI20
IDI19
IDI18
IDI17
IDI16
BASE + 3H
IDI31
IDI30
IDI29
IDI28
IDI27
IDI26
IDI25
IDI24
PCI-1730/1733/1734 User Manual
40
BASE+0H/1H (/2H/3H)
The PCI-1730 offers 16-ch isolated digital output channels. These channels use the
registries at addresses BASE+0H/1H.
Table C-3 Register for Isolated Digital Output
Write
Isolated Digital Output
Bit #
7
6
5
4
3
2
1
0
BASE + 0H
IDO7
IDO6
IDO5
IDO4
IDO3
IDO2
IDO1
IDO0
BASE + 1H IDO15
IDO14
IDO13
IDO12
IDO11
IDO10
IDO9
IDO8
The PCI-1734 offers 32-ch isolated digital output channels. These channels use the
registries at addresses BASE+0H/1H/2H/3H.
Table C-4 Register for Isolated Digital Output
Write
Isolated Digital Output
Bit #
7
6
5
4
3
2
1
0
BASE + 0H
IDO7
IDO6
IDO5
IDO4
IDO3
IDO2
IDO1
IDO0
BASE + 1H IDO15
IDO14
IDO13
IDO12
IDO11
IDO10
IDO9
IDO8
BASE + 2H IDO23
IDO22
IDO21
IDO20
IDO19
IDO18
IDO17
IDO16
BASE + 3H IDO31
IDO30
IDO29
IDO28
IDO27
IDO26
IDO25
IDO24
C.5 Non-isolated Digital Input Registers
BASE+2H/3H
The PCI-1730 offers 16-ch digital input channels. These channels use the input ports
at addresses BASE+2H/3H.
Table C-5 Register for Digital Input
Read
Digital Input
Bit #
7
6
5
4
3
2
1
0
BASE + 2H
DI7
DI6
DI5
DI4
DI3
DI2
DI1
DI0
BASE + 3H
DI15
DI14
DI13
DI12
DI11
DI10
DI9
DI8
41
PCI-1730/1733/1734 User Manual
Appendix C Register Structure & Format
C.4 Isolated Digital Output Register
C.6 Non-isolated Digital Output Register
BASE+2H/3H
The PCI-1730 offers 16-ch digital output channels. These channels use the input
ports at addresses BASE+2H/3H.
Table C-6 Register for Digital Output
Write
Digital Output
Bit #
7
6
5
4
3
2
1
0
BASE + 2H
DO7
DO6
DO5
DO4
DO3
DO2
DO1
DO0
BASE + 3H DO15
DO14
DO13
DO12
DO11
DO10
DO9
DO8
C.7 Board ID — BASE+4H
The PCI-1730/1733/1734 offers Board ID register BASE+4H. With correct Board ID
settings, user can easily identify and access each card during hardware configuration
and software programming.
Table C-7 Register for Board ID
Read
Bit #
Board ID
7
6
5
4
BASE + 4H
3
2
1
0
BD3
BD2
BD1
BD0
BD3 ~ DB0 Board ID
BD0
LSB of the Board ID
BD3
MSB of the Board ID
BD3 BD2 BD1 BD0 Board ID
1
1
1
1
15
1
1
1
0
14
1
1
0
1
13
1
1
0
0
12
1
0
1
1
11
1
0
1
0
10
1
0
0
1
9
1
0
0
0
8
0
1
1
1
7
0
1
1
0
6
0
1
0
1
5
0
1
0
0
4
0
0
1
1
3
0
0
1
0
2
0
0
0
1
1
0
0
0
0
0
PCI-1730/1733/1734 User Manual
42
BASE+8H/CH/10H
The PCI-1730 Interrupt Status Register control the status of four interrupt signal
sources (IDI0, IDI1, DI0, DI1).
Table C-8 Register for Interrupt Status
Read
Bit #
Interrupt Status Register
7
6
5
4
3
2
1
0
BASE + 8H
DI1EN
DI0EN
IDI1EN IDI0EN
BASE + CH
DI1RF
DI0RF
IDI1RF
IDI0RF
BASE + 10H
DI1F
DI0F
IDI1F
IDI0F
IDI/DInF
Interrupt flag bits (n = 0 ~ 1)
This bit is a flag indicating the status of an interrupt. User can read this bit to get the
status of the interrupt
0
No interrupt
1
Interrupt occurred
IDI/DInEN
0
1
Interrupt enable control bits (n = 0 ~ 1)
Read this bit to Enable/Disable the interrupt.
Disable
Enable
IDI/DInRF
Interrupt triggering control bits (n = 0 ~ 1)
The interrupt can be triggered by a rising edge or falling edge of the interrupt signal,
as determined by the value in this bit.
0
Rising edge trigger
1
Falling edge trigger
The PCI-1733 Interrupt Status Register control the status of four interrupt signal
sources (IDI0, IDI1, IDI16, IDI17).
Table C-9 Register for Interrupt Status
Read
Bit #
Interrupt Status Register
7
6
5
4
3
2
1
0
BASE + 8H
IDI17EN IDI16EN IDI1EN IDI0EN
BASE + CH
IDI17RF IDI16RF IDI1RF
BASE + 10H
IDI17F
43
IDI16F
IDI1F
IDI0RF
IDI0F
PCI-1730/1733/1734 User Manual
Appendix C Register Structure & Format
C.8 Interrupt Status Register
IDInF
Interrupt flag bits (n = 0, 1, 16, 17)
This bit is a flag indicating the status of an interrupt. User can read this bit to get the
status of the interrupt
0
No interrupt
1
Interrupt occurred
IDInEN
0
1
Interrupt enable control bits (n = 0, 1, 16, 17)
Read this bit to Enable/Disable the interrupt.
Disable
Enable
IDInRF
Interrupt triggering control bits (n = 0, 1, 16, 17)
The interrupt can be triggered by a rising edge or falling edge of the interrupt signal,
as determined by the value in this bit.
0
Rising edge trigger
1
Falling edge trigger
C.9 Interrupt Control Register — BASE+8H/CH/10H
The PCI-1730 Interrupt Control Register controls the status of four interrupt signal
sources (IDI0, IDI1, DI0, DI1). The user can clear the interrupt by writing its corresponding value to the Interrupt Control Register, as shown in below table.
Table C-10 Register for Interrupt Control
Write
Bit #
Interrupt Control Register
7
6
5
4
3
2
BASE + 8H
DI1EN
DI0EN
IDI1EN IDI0EN
BASE + CH
DI1RF
DI0RF
IDI1RF
BASE + 10H
1
0
IDI0RF
DI1CLR DI0CLR IDI1CLR IDI0CLR
IDI/DInCLR
Interrupt clear control bits (n = 0 ~ 1)
This bit must first be cleared to service the next interrupt.
0
Don’t care
1
Clear the interrupt
IDI/DInEN
0
1
Interrupt enable control bits (n = 0 ~ 1)
Read this bit to Enable/Disable the interrupt.
Disable
Enable
IDI/DInRF
Interrupt triggering control bits (n = 0 ~ 1)
The interrupt can be triggered by a rising edge or falling edge of the interrupt signal,
as determined by the value in this bit.
0
Rising edge trigger
1
Falling edge trigger
PCI-1730/1733/1734 User Manual
44
Table C-11 Register for Interrupt Control
Write
Bit #
Interrupt Control Register
7
6
5
4
3
2
1
0
BASE + 8H
IDI17EN IDI16EN IDI1EN IDI0EN
BASE + CH
IDI17RF IDI16RF IDI1RF
BASE + 10H
IDI17CLR IDI16CLR
IDI0RF
IDI1CLR IDI0CLR
IDInCLR
Interrupt clear control bits (n = 0, 1, 16, 17)
This bit must first be cleared to service the next interrupt.
0
Don’t care
1
Clear the interrupt
IDInEN
0
1
Interrupt enable control bits (n =0, 1, 16, 17)
Read this bit to Enable/Disable the interrupt.
Disable
Enable
IDInRF
Interrupt triggering control bits (n = 0, 1, 16, 17)
The interrupt can be triggered by a rising edge or falling edge of the interrupt signal,
as determined by the value in this bit.
0
Rising edge trigger
1
Falling edge trigger
45
PCI-1730/1733/1734 User Manual
Appendix C Register Structure & Format
The PCI-1733 Interrupt Control Register controls the status of four interrupt signal
sources (IDI0, IDI1, IDI16, DI17). The user can clear the interrupt by writing its corresponding value to the Interrupt Control Register, as shown in below table.
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2007