AMX | DXLink HDMI MMF-D | Data Sheet - DXLink HDMI Multimode Fiber Receiver, Duplex

DATA SHEET
DXLink HDMI Multimode Fiber Receiver,
Duplex
TM
DXLF-HDMIRX-MM-D (FG1010-562)
Overview
The DXLink HDMI Fiber Receiver features built-in SmartScale® Technology to deliver HDMI
with HDCP that is perfectly scaled for each connected display automatically, eliminating
the integration challenges that can occur when sources and displays have different optimal
resolutions. It accepts audio, video, control and Ethernet over multimode fiber from up to
300 meters. Mount the low-profile DXLink Fiber Receiver behind a display or above a
ceiling mounted projector and control it using the built in RS-232 or IR ports. Plus monitor
the connected display's settings, and send IR control signals to the Enova DGX Digital
Media Switcher with integrated NetLinx® control back to the source device.
COMMON APPLICATIONS
The ideal solution for any destination display or projector designed into an Enova DGX integrated system that
requires the distance capabilities and inherent security of fiber – or both; including campus-wide distribution of
sources that are shared between classrooms, secure military applications, casinos, arenas and museums. Directly
connect LCDs, plasmas and projectors using the HDMI output connection while delivering room audio via the
stereo audio output.
FEATURES

HDCP Compliance Over Fiber – Transmit HDCP compliant video including HDMI up to 300 m

Industry Leading Data Rate – DXLink is leading the way with an optical transport rate of 10 Gbps

SmartScale® Technology – Automatically responds to the display's declared EDID information and scales the
video to the best resolution and video parameters for that display without manual setup; this prevents
inferior video quality when sources are forced to lower resolutions to support the least capable display in the
system

Secure and Isolated – Fiber inherently provides extra security and electrical isolation making it the transport
method of choice for many mission-critical secure environments

InstaGate Pro® Technology – Easily integrate HDCP into system designs and enjoy hassle free matrix
switching to all compliant displays, no tools, no delays and no key constraints – it just works

Native NetLinx® Control Everywhere – Control connected source devices using the built-in IR and RS-232
ports

Field Serviceable Fiber Modules – Easily remove and replace SFP modules in the field

Ethernet Connectivity – Provides ICSLan Ethernet support at the Receiver – add Ethernet connectivity to a
Touch Panel, plug in a WAP or stream IP audio/video to a Ethernet enabled source device

IR Receiver – Send IR commands back to the Enova DGX to control source equipment using an IR remote
© 2013 AMX. All rights reserved.
SPECIFICATIONS
GENERAL
Dimensions (HWD)
Weight
Shipping Weight
MTBF
Noise Level
Airflow
Mounting Options
Regulatory Compliance
Included Accessories
Optional Accessories
Compatible AMX Products
1” x 8 3/4” x 5 1/5” (2.54 x 22.12 cm x 13.08 cm)
Approx. 1.1 lb (0.50 kg)
Shipping Weight: Approx. 2.20 lb (1.00 kg)
Approx. 2.2 lb (1 kg)
124,232 hours
TBA
TBA
Compatible V Style mounting options:
•AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack
Mounting Tray with Fill Plates (FG1010-721)
•AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting
Tray (FG1010-720)
•AVB-VSTYLE-SURFACE-MNT, V Style Single Module
Surface Mount Brackets (FG1010-722)
•AVB-VSTYLE-POLE-MNT, V Style Single Module Pole
Mounting Kit (FG1010-723)
•Class 1 Eye safe per requirements of IEC 60825-1 /
CDRH
•RoHS / WEEE Compliant
Ships with a desktop power supply with power cord
•AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack
Mounting Tray with Fill Plates (FG1010-721)
•AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting
Tray (FG1010-720)
•AVB-VSTYLE-SURFACE-MNT, V Style Single Module
Surface Mount Brackets (FG1010-722)
•AVB-VSTYLE-POLE-MNT, V Style Single Module Pole
Mounting Kit (FG1010-723)
•CC-NIRC, NetLinx IR Emitter Cable (FG10-000-11)
•IR03, External IR Receiver Module (FG-IR03)
•Enova DGX 8/16/32/64 Digital Media Switchers with
ENOVADGX-VO-DXLINK-MMF-D, Enova DGX DXLink
Mutimode Fiber Output Board, Duplex (FG1058-632)
installed
ACTIVE POWER REQUIREMENTS
AC Power
Power Consumption (Max)
Power Connector
TBA
TBA
TBA
POWER SUPPLY
External, Included
Each HDMI RX ships with a desktop power supply with
power cord
2
ENVIRONMENTAL
Temperature (Operating)
Temperature (Storage)
Humidity (Operating)
Humidity (Storage)
Heat Dissipation (On)
32° to 104° F (0° to 40° C)
-22° to 158° F (-30° to 70° C)
5% to 85% RH (non-condensing)
0% to 90% RH (non-condensing)
TBA
ETHERNET
Ethernet Connection
(1) RJ-45, TCP/IP Port (ICS LAN 10/100)
DXLINK FIBER
Fiber Connector
Fiber Cable Type
Fiber Cable Length
Transport Layer Throughput
Fiber Transceiver Type
Optical Wavelength
Optical Budget
LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS
10A)
OM3 50/125µm
300m (984 ft)
10.3125 Gbps
10G SFP+
850 nm
6.8 dB (typical), 3.2 dB (stressed) between DXLink
Fiber Transceivers
Optical Modulation Amplitude (OMA): -4.3 dBm (min)
Optical Transceiver Mean
Optical Modulation Amplitude (OMA) Sensitivity: -11.1
dBm (typ), -7.5 dBm (stressed)
-1 dBm (average power)
HDMI
Output Connector
Compatible Formats
Signal Type Support
Progressive Resolution Support
Interlaced Resolution Support
Output Scaling
3D Format Support
Deep Color Support
Color Space Support
(1) HDMI Type A Female
HDMI, HDCP , DVI
HDMI
DVI-D (single link with HDMI cable adapter)
All progressive resolutions between 480p and 1920 x
1200 @ 60 Hz via automatic SmartScale query of the
display's preferred EDID Detailed Timing Definition
480i, 576i, 1080i (including but not
limited to those resolutions shown in the “Instruction
Manual – DXLink Fiber Transmitters and Receivers”
Note-Reminder: Interlace video supported into the
Transmitter, progressive only supported out of the
Receiver unless in non-scaling Bypass
SmartScale or Manual Configuration or Bypass
Yes, if Scaler on RX is set to Bypass mode
Frame Packing 1080p 24Hz
Frame Packing 720p 50/60Hz
Frame Packing 1080i 50/60Hz
Top-Bottom 1080p 24Hz
Top-Bottom 720p 50/60Hz
Side-by-Side Half 1080i 50/60Hz
24-bit, 30-bit, 36-bit
30-bit and 36-bit supported when the HDMI DXLink
RX Scaler is in Bypass mode and format is 1080p60 or
less
RGB 4:4:4
3
HDCP Support
CEC Support
Propagation Delay (Typical)
CDR (Re-Clocking)
Output Voltage (Nominal)
Output Rise Time / Fall Time
Video Data Rate (Max)
Video Pixel Clock (Max)
Audio Format Support
Audio Resolution
Audio Sample Rate
Local Audio Support
YCbCr 4:4:4 and 4:2:2
(Input signal support for YCbCr 4:4:4 and 4:2:2, output
color-space is converted to RGB 4:4:4)
Yes
Supports AMX HDCP InstaGate Pro Technology
When used with an Enova DGX Digital Media Switcher
the key support is up to 16 sinks per output,
independent of source device
None
26 ms when scaling, 5.2 us when in Bypass mode
Yes
1.0 Vpp Differential
425 ps typ (20% - 80%)
4.95 Gbps / 6.75 Gbps
6.75 Gbps supported if Scaler on corresponding output
board or DXLink Fiber RX is set to Bypass mode and
format is 1080p60 or less
165 MHz / 225 MHz
225 MHz supported if Scaler on corresponding output
board or DXLink Fiber RX is set to Bypass mode and
format is 1080p60 or less
Dolby TrueHD, Dolby Digital, DTS-HD Master Audio,
DTS, 2 CH through 8 CH L-PCM Dolby Digital and DTS
support up to 48kHz, 5.1 channels
16 bit to 24 bit
32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
Extraction
ANALOG AUDIO
Output Connections
Output Signal Types
Output Level (Max)
Output Frequency Response
Audio THD+N
Audio S/N Ratio
Digital to Analog Reference Level
Audio Synchronization
3.5mm Mini-Stereo Jack
Stereo Analog
TBA
TBA
TBA
TBA
TBA
Video formats @ 60Hz frame rate: video formats @
60Hz frame rate: In scaling mode audio leads video by
12ms typ (4ms to 20ms). In Bypass mode, audio lags
video by 14ms
USB (HID) KEYBOARD & MOUSE
USB (HID)
(1) USB Mini A/B Connector; connect a keyboard &
mouse and send commands to a PC connected to a
DXLink Twisted Pair or Fiber TX
CONTROLS
ID Pushbutton
Advanced Configuration Interface
Serial
Toggle between DHCP and static IP addressing
Places system in NetLinx Device ID assignment mode
Reset the factory default settings
Restore the factory firmware image
(1) USB Mini-B Connector (“PROGRAM”)
(1) 3.5mm Pluggable Phoenix Terminal Block
Bidirectional RS-232
Standard NetLinx Baudrate 1200-115k
Parity support Odd/Even/None
4
IR RX
IR TX
(1) 3.5mm Mini-Stereo Jack
Port for IR03 Receiver (Optional)
(1) 3.5mm Pluggable Phoenix Terminal Block
Port for IR01 Emitter (Optional)
INDICATORS
Power Indicator
Video Indicator
Audio Indicator
Scaling Button and LEDs
IR TX Indicator
IR RX Indicator
RS-232 TX Indicator
RS-232 RX Indicator
LINK/ACT
Status
CEC Indicator
USB Indicator
ID Pushbutton
(1) LED that lights:
•Green during normal operation state
•Red when power is applied and boot sequence is
started
•Yellow when system initialization is in process
(1) Green LED indicates the presence of video and
audio
signals through the module
(1) Green LED indicates the presence of audio signals
through the module
(1) Pushbutton and (3) Green LEDs; use Scaling button
to select one of the three options: Bypass, Auto
(SmartScale), or Manual. The factory default is Auto
(SmartScale). If the RX power cycles, it defaults to the
last persisted mode (achieved by pressing scaling
button and holding it until the desired scaling mode
LED flashes)
(1) Red LED lights during the transmission of IR data
via the rear IR port
(1) Yellow LED lights during the receipt of IR data via
the rear IR port
(1) Red LED shows serial transmit (TX) data activity
(1) Yellow LED shows serial receive (RX) data activity
(1) Green LED lights when the Ethernet cable is
connected and an active link is established. This LED
also blinks when receiving Ethernet data packets
(1) Green LED lights when the Controller is
programmed and communicating properly
Not currently supported
(1) Yellow LED lights when either a Keyboard or mouse
is connected directly to the RX, or either and/or both
are connected to a USB Hub connected to the RX
Places system in NetLinx Device ID assignment mode
FRONT CONNECTORS
Advanced Configuration Interface
(1) USB Mini-B Connector
BACK CONNECTORS
Local Power
DXLink Fiber Input
ICS LAN/Ethernet Port
Serial
IR RX
IR TX
TBA
LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS
10A)
RJ-45 Connector, TCP/IP Port (ICS LAN 10/100)
3.5mm Pluggable Phoenix Terminal Block
Bidirectional RS-232
Standard NetLinx Baudrate 1200-115k
Parity support Odd/Even/None
(1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver
(Optional)
(1) 3.5mm Pluggable Phoenix Terminal Block Port for
IR01 Emitter (Optional)
5
USB (HID) Keyboard & Mouse
HDMI Output
Analog Stereo Output
(1) USB Mini A/B Connector; connect a keyboard &
mouse and send commands to a PC connected to a
DXLink Twisted Pair or Fiber
HDMI Type A Female
3.5mm Mini-Stereo Jack
For a detailed pictorial drawing please visit: http://www.amx.com/products/DXLF-HDMIRX-MM-D.asp
About AMX
AMX hardware and software solutions simplify the implementation, maintenance, and use of technology to create effective environments. With the increasing number of
technologies and operating platforms at work and home, AMX solves the complexity of managing this technology with reliable, consistent and scalable systems. Our award-winning
products span control and automation, system-wide switching and audio/video signal distribution, digital signage and technology management. They are implemented worldwide in
conference rooms, homes, classrooms, network operation / command centers, hotels, entertainment venues, broadcast facilities, and more. ©2013 AMX. All rights reserved.
Specifications subject to change. Revised 11-Oct-2013.
AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
6
Download PDF