ADEMCO | Vista-128FB | VISTA-128FB - Activated Alarm Security System

VISTA-128FB
Commercial Fire & Burglary
Partitioned Security System
with Scheduling
Quick Start Guide
V128FB-PR 5/98
–2–
Table Of Contents
RECOMMENDED PROGRAMMING PROCEDURE ................................................................................................. 4
PROGRAM FIELD CATEGORIES ............................................................................................................................. 6
VISTA-128FB PROGRAMMING FORM..................................................................................................................... 7
PARTITION-SPECIFIC PROGRAMMING FORM.................................................................................................... 13
PROGRAMMING WITH #93 MENU MODE ............................................................................................................. 15
SYSTEM LAYOUT WORKSHEETS......................................................................................................................... 17
OUTPUT RELAYS WORKSHEETS ......................................................................................................................... 29
ALPHA DESCRIPTOR VOCABULARY.................................................................................................................... 32
RELAY VOICE DESCRIPTORS AND CUSTOM WORD SUBSTITUTES VOCABULARY ..................................... 33
SCHEDULING MENU PROMPTS............................................................................................................................ 34
SCHEDULING WORKSHEETS ............................................................................................................................... 35
5800 SERIES RF TRANSMITTER LOOP DESIGNATIONS.................................................................................... 40
VISTA-128FB SUMMARY OF CONNECTIONS ...................................................................................................... 43
The purpose of this document is to provide a quick and easy way to program your entire system. A recommended
programming procedure is included, followed by a list of program fields with the corresponding program group they
belong to (system-wide, partition-specific, scheduling, etc.). Two program forms are included, one contains all the
programming fields, and the other contains the partition-specific fields. If you are setting up a single-partition
system, the partition-specific fields become system-wide fields.
Following the program forms are system layout worksheets. We recommend that you use these sheets to plan
your system before programming is performed. If you need further information about specific programming
options, see the VISTA-128FB INSTALLATION INSTRUCTIONS.
•
Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."
Single Partition System
• The system default is for a single partition system. Use the VISTA-128FB SINGLE PARTITION
PROGRAMMING FORM when programming for single partition usage. Follow the steps outlined in
RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.
Multiple-Partition System
• You must enter the number of partitions you are using in data field 2*00 to set the system for multiple
partitions. Use the VISTA-128FB SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM
FORMS when programming the system for multiple partitions.
Follow the steps outlined in
RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.
•
•
•
•
•
•
•
•
•
•
SUMMARY OF PROGRAMMING COMMANDS
To enter program mode, enter installer code + [8] + [0] + [0] + [0]
To set standard defaults, press *97
To set communication defaults, press *94 + one of the following: *80=low speed; *81=Ademco Express;
*82=Ademco High Speed; *83=Ademco's Contact ID
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account & phone number field entries, press [*] + field number + [*]
To assign zone descriptors, press #93 + follow menu prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu prompts
To exit program mode, press *99 OR *98: *99 allows re-access to programming mode by installer code. *98
prevents re-access to programming mode by installer code.
Standard default (*97) values are shown in brackets [ ], otherwise default = 0.
–3–
Recommended Programming Procedure
The following is a step-by-step procedure recommended for programming your VISTA-128FB
system.
1. Set the keypads (and other peripheral devices) to the appropriate addresses.
2. Set factory defaults by pressing *97.
This will automatically enable keypad addresses 00-01, so be sure at least one keypad is set
to one of these addresses
3. Program system-wide (global) data fields.
Using the programming form as a guide, enter program mode and program all system wide
programming fields. These options affect the entire system, regardless of partitions. They
include control options, downloader and dialer options, RF options, event logging options, etc.
Refer to the COMPLETE LIST OF PROGRAMMING FIELDS for a listing of the program fields
arranged by function.
Note that field 2*00 (number of partitions) & field 1*32 (RF expander type) must be
programmed before continuing.
4. Program partition-specific fields.
When the system-wide fields have been programmed, program all partition-specific
programming fields by first pressing *91 to select a partition (while still in data field program
mode). Then enter the first partition-specific field number *09. The next partition-specific field
will automatically be displayed when you are finished entering the value for field *09. Partitionspecific fields can have different values for each partition. To program the fields for the next
partition, press *91, enter the desired partition number, then enter field *09. Refer to the
MECHANICS OF PROGRAMMING section in the VISTA-128FB INSTALLATION
INSTRUCTIONS for detailed instructions.
5. Use #93 Menu Mode for device programming.
Refer to the DEVICE PROGRAMMING section to assign keypad ID numbers and default
partitions for each keypad, and to selectively suppress certain keypad sounding options. Also
use this mode to assign RF receivers, relay modules, the VIP module, the ecp Long Range
Radio, and the Vista Gateway Module.
6. Use #93 Menu Mode for zone programming.
Refer to the ZONE PROGRAMMING section to program zone response types, assign right
loop zones and wireless zones, assign zones to partitions, and to program alarm report codes.
7. Use #93 Menu Mode for programming relays.
Refer to the RELAY PROGRAMMING section to program desired relay operation.
8. Program Communication options.
Refer to the COMMUNICATION PROGRAMMING section for further instructions to load
communication defaults and to program related fields. Then use #93 mode to program report
codes if necessary.
9. Use #93 Menu Mode for programming alpha descriptors.
Refer to the ALPHA PROGRAMMING section to enter zone and partition descriptors and a
custom installer's message.
10. Use #93 Menu Mode for relay voice descriptors and custom word substitutes.
Refer to the RELAY VOICE DESCRIPTORS section for further instructions for programming
relay descriptors to be annunciated by the VIP module, as well as the CUSTOM INDEX
section for custom word substitutes.
11. Use #80 Mode for programming schedules.
Refer to the SCHEDULING section to program open/close schedules, temporary and holiday
schedules, limitation of access schedules, and time driven events.
12. Define user access codes.
Refer to SECURITY ACCESS CODES section to program authority level, O/C reporting
option, partition assignments, and wireless key assignments for each user.
–4–
13. Exit Programming Mode.
Exit programming mode by pressing either *98 or *99. Additional entries of *99 is required if
the exit is being done from fields 1*00 and above.
To prevent re-access to programming mode using the Installer's code, use *98. The only way
to re-access programming mode is by depressing both the [*] and [#] keys at the same time
within 30 seconds of power up.
Exiting by using *99 always allows reentry into programming mode using the Installer's code.
Either way of exiting will allow access via downloading. Note that if local programming lockout
is set via downloading, programming mode cannot be entered at the keypad.
–5–
Program Field Categories
In the following pages, the programming fields have been arranged by category. Use this index to cross reference
the numerical ordered fields on the programming form.
Field
*00
*08
*09
*10
*11
*12
*13
*15
*16
*17
*19
*20
*22
*23
*24
*25
*26
*27
*28
*29
*30
*31
*32
*33
*34
*35
*36
*37
*38
*39
*40
*41
*42
*43
*44
*45
*46
*47
*48
*49
*50
*51
*52
*53
*56
*57
*58
*59
*64
*65
*66
*67
*68
Group
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
System-Wide
System-Wide
Communications
Communications
System-Wide
Partition-Specific
Communications
Communications
Partition-Specific
Communications
Communications
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Communications
System-Wide
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Field
*69
*70
*71
*72
*73
*74
*75
*76
*79
*80
*83
*84
*85
*87
*88
*89
*90
1*01
1*02
1*03
1*04
1*05
1*06
1*07
1*08
1*09
1*17
1*18
1*19
1*20
1*21
1*22
1*23
1*24
1*25
1*26
1*28
1*29
1*30
1*31
1*32
1*33
1*34
1*42
1*43
1*44
1*45
1*47
1*48
1*49
1*52
1*53
1*56
Group
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Communications
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Communications
Partition-Specific
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
#93 Menu Mode
System-Wide
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Communications
Communications
Communications
Partition-Specific
System-Wide
Partition-Specific
Partition-Specific
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
–6–
Field
1*57
1*58
1*60
1*70
1*71
1*72
1*73
1*74
1*75
1*76
1*77
2*00
2*01
2*02
2*05
2*06
2*07
2*08
2*09
2*10
2*11
2*18
2*19
2*20
2*21
2*22
2*23
2*24
3*00
3*01
3*12
3*13
3*14
3*15
3*16
3*17
3*18
3*19
3*20
3*21
3*30
3*31
3*50
3*55
3*56
3*57
3*59
3*60
3*61
3*82
3*85
Group
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
Partition-Specific
Partitioning
Partition-Specific
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
System-Wide
Partition-Specific
Partition-Specific
Partition-Specific
System-Wide
System-Wide
System-Wide
VISTA 128FB Programming Form
Some fields are programmed for each partition (shown as shaded fields). If Programming a Multiple Partition System, see the
PARTITION-SPECIFIC section for programming these fields. Standard default (*97) values are shown in brackets [ ],
otherwise default = 0.
| | |
*00 INSTALLER CODE
*24 IGNORE EXPANSION ZONE TAMPER
*08 TEMPORAL SIREN PULSE
[0]
*25 BURG.TRIGGER FOR RESPONSE TYPE 8
1 = Yes; 0 = No
*09 ENTRY DELAY #1
|
[02]
*26 INTELLIGENT TEST REPORTING
00-15 times 15 seconds
Maximum "04" for UL Listed installations.
*11 ENTRY DELAY #2
*29 QUICK ARM
*30 MAIN DIALER (TOUCHTONE OR ROTARY) [0]
01-15 times 2 minutes. Minimum 16 min. for UL Commercial
Burglary and 6 min. for Commercial Fire.
1=TouchTone; 0=rotary
*31 PABX ACCESS CODE
[0]
|
|
|
|
|
|
|
|
00-09; B-F (11-15)
Enter partition in which keyswitch used,
1-8; 9=Silences bells if fire present; 0=disable
*32 PRIM. SUBS. ACCT #
*16 BELL 1 CONFIRMATION OF ARMING DING [0]
Enter 00-09; B-F (11-15) [15 15 15 15]
*33 PRIMARY PHONE NUMBER
1=enable; 0=disable. Must be "1" for UL Burglary
Installations.
*17 AC LOSS KEYPAD SOUNDING
[1]
1=yes; 0=no
|
[04]
[1]
1=yes; 0=no; "1" for UL.
00-15 times 15 seconds (must be longer than Exit Delay #1)
Maximum "04" for UL Commercial Burglary installations.
*15 KEYSWITCH ASSIGNMENT
*28 POWER UP IN PREVIOUS STATE
|
[08]
| |
Enter interval in hours, 001-999; 000=no report ; Max.
024 for Commercial Fire & UL.
|
00-15 times 15 seconds (must be longer than Entry Delay #1).
Maximum "03" for UL Commercial Burglary installations.
*13 BELL 1 TIMEOUT
[024]
*27 TEST REPORT INTERVAL
[06]
*12 EXIT DELAY #2
[0]
1=yes, (no report sent if any other report was recently
sent); 0=no.. Must be 0 for Commercial Fire & UL
Commercial Burglary.
|
[03]
[1]
1=enable; 0=disable
00-15 times 15 seconds
Maximum "03" for UL Commercial Burglary installations.
*10 EXIT DELAY #1
[0]
1=Ignore; 0=Enable tamper for RF and RPMs. Must be "0" for
UL installations if using these devices.
Enter 4 digits, 0-9 [5140]
[0]
1=yes; 0=no
*19 RANDOMIZE AC LOSS REPORT
[2]
1=10-40 min; 2=6-12 hrs; 0=normal report (about 2 min.
after AC loss). Must be "2" for Central and Remote
Station Fire alarm systems.
|
*20 VIP MODULE PHONE CODE
|
Enter 01 - 09 for the first digit; enter [00]
, [11]
11 for "*" or 12 for "#" for the second digit. This field
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*35 DOWNLOAD PHONE No.
Must be set to "0" for Commercial Fire & UL
Commercial Burglary installations.
*22 KEYPAD PANIC ENABLE
1=enable; 0=disable
*23 MULTIPLE ALARMS
1=yes; 0=no
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*34 SECONDARY PHONE NUMBER
[001]
995 996
[1]
999
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*36 DOWNLOAD ID No.
|
|
|
|
|
|
|
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
–7 –
|
*37 DOWNLOAD COMMAND ENABLES
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
0
Dialer
System
Shutdwn Shutdwn
Not
Used
[0 0 0 0 0 0]
Remote Remote
Bypass Disarm
Remote UploadDownload
Arm Program Program
See field 1*53 for Callback disable option; [1=enable];
0=disable; For Commercial Fire & UL installations, all
entries must be "0."
*38 PREVENT ZONE XXX BYPASS
[000]
Alarm
Rstr
Bypass Trbl Opn/Cls
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0 0 0 0 0 0]
| |
Alarm
Rstr
Bypass Trbl Opn/Cls
*39 ENABLE OPEN/CLOSE REPORT FOR
[1]
*56 USE LRR ONLY
INSTALLER CODE 1=enable; 0=disable
[0]
*57 LRR IF DIALER FAILS
1=enable; 0=disable
*58 LRR ENABLE CS #1
[0]
1=N.C.loops; 0=EOLR supervision; Must be "0" for
Commercial Fire & UL.
*42 DIAL TONE PAUSE
[0 0 0 0 0 0]
Alrm Trbl Byp O/C Syst
Tst
0=disable, 1=enable for reports for primary subs id of LRR
[0]
*59 LRR ENABLE CS#2
0=5 seconds; 1=11 seconds; 2=30 seconds; Must be
"0" Commercial Fire & UL.
*43 DIAL TONE DETECTION
[0 0 0 0 0 0]
Alrm Trbl
Byp O/C Syst
Tst
0=disable, 1=enable for reports for secondary subs id of LRR
[1]
1=wait for true dial tone; 0=pause, then dial
*44 RING DETECTION COUNT
*64 PAGER INSTALLED
|
[00]
*45 PRIMARY FORMAT
*65 PAGER PHONE # FOR ALARMS
[0]
0=Low Speed; 1=Contact ID; 2=Ademco High Speed;
3=Ademco Express
*46 LOW SPEED FORMAT (Primary)
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
[0]
*66 PAGER ID # FOR ALARMS
0=Ademco Low Speed; 1=Sescoa/Radionics
*47 SECONDARY FORMAT
[0]
Enter up to 10 digits for the pager id #
0=Low Speed; 1=Contact ID; 2=Ademco High Speed;
3=Ademco Express
*48 LOW SPEED FORMAT (Sec.)
*67 PAGER PHONE # FOR TROUBLES
[0]
0=Ademco Low Speed; 1=Sescoa/Radionics
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
[0] [0]
Prim
[0]
0=No, 1=Yes, alpha numeric pager interface is installed.
01-14; 15=answering machine; 00=no detection. Must
be "00" for Commercial Fire & UL Burglary.
Sec
*68 PAGER ID # FOR TROUBLES
[0]
1=Sescoa; 0=Radionics
*51 DUAL REPORTING
[0]
0=No, 1=Yes, if radio is to be used as a backup to dialer
*41 NORMALLY CLOSED or EOLR (Zones 3-8)
*50 SESCOA/RADIONICS SELECT
[0]
0=No, 1=Yes, if built-in dialer will not be used.
*40 OPEN/CLOSE REPORT FOR KEYSWITCH
1=yes; 0=no
Low Bat
0=standard; 1=expanded;
Note: Expanded overrides 4+2 format.
001-128; 00 if all zones can be bypassed
*49 CHECKSUM VERIFICATION
Low Bat
0=standard; 1=expanded;
Note: Expanded overrides 4+2 format.
Enter up to 10 digits for the pager id #
*69 PAGER PHONE # FOR BYPASSES
[0]
1=yes; 0=no If used with Spilt Reporting "1" option (1*34),
alarms and alarm restores go to both primary & secondary
numbers, while all other reports go to secondary only. If used
with Split Reporting "2" option, alarms and alarm restores go
to both, open/close and test messages go to secondary only,
while all other reports go to primary. If used with Split
Reporting "3" option, fire alarms and fire supervisory signals
go to both primary and secondary, while all other reports go to
secondary only.
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*70 PAGER ID # FOR BYPASSES
Enter up to 10 digits for the pager id #
–8 –
*71 PAGER PHONE # FOR OPENS/CLOSES
|
*90 SEC. SUBS. ACCT #
Enter 00-09; B-F (11-15)
|
|
|
[15 15 15 15]
1*17 LOBBY PARTITION
[0]
Enter the "common lobby" partition (1-8)
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
1*18 AFFECTS LOBBY
*72 PAGER ID # FOR OPENS/CLOSES
[0]
Enter 1 if this partition affects the common lobby; enter 0 if it
does not. Must be "0" for Commercial Fire & UL installations.
Enter up to 10 digits for the pager id #
1*19 ARMS LOBBY
*73 PAGER PHONE # FOR SYSTEM
[0]
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not. Must be "0" for Commercial Fire & UL
installations.
1*20 EXIT ERROR LOGIC
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
[0]
0=No, 1=Bypass E/E and Interior zones faulted after exit
delay. Must be "0" for Commercial Fire & UL installations.
*74 PAGER ID # FOR SYSTEM
1*21 EXIT DELAY RESET
[0]
0=No; 1=Resets Exit Delay to 60 seconds after zone
is closed. Must be "0" for Commercial Fire & UL
Enter up to 10 digits for the pager id #
*75 PAGER PHONE # FOR TEST
installations.
FIELDS 1*22-1*25: Allow four sets of two zones each to be
linked so that both must fault within a five minute period to
cause an alarm.
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*76 PAGER ID # FOR TEST
Enter up to 10 digits for the pager id #
ZONE TYPE RESTORE ENABLES
*79 FOR ZONE TYPES 1-8
*80 FOR TYPES 9/10
1*22 CROSS-ZONING PAIR ONE
| |
| |
1*23 CROSS-ZONING PAIR TWO
| |
| |
1*24 CROSS-ZONING PAIR THREE
| |
| |
1*25 CROSS-ZONING PAIR FOUR
| |
| |
1*26 PANIC BUTTON OR SPEEDKEY
[00, 00, 00, 00]
1
2
3
4
5
6
7
8
9
10
1=enable; [0=disable]
*83 FIRST TEST REPORT TIME
|
|
|
[03]
|
|
|
A
B
C
D
Enter speedkey macro # (01-35) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# or 00 to select macro when key is pressed.
[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 0059; 00 in all boxes=instant (Day 01= Monday)
*84 SWINGER SUPPRESSION
|
MISCELLANEOUS WIRELESS OPTIONS
Fields 1*28 - 1*32 are not applicable to Commercial
Fire or UL installations.
|
01-15 alarms; Must be "00" (disabled) for UL.
1*28 RF TX LOW BATTERY SOUND
*85 ENABLE DIALER REPORTS [0]
FOR PANICS & DURESS
1=immediate; 0=when disarmed
995
996
999 Duress
1*29 RF TX LOW BATTERY REPORT ENABLE [0]
1=enable; 0=disable
*87 ENTRY WARNING
1*30 RF RCVR CHECK-IN INTERVAL
[0]
0=Instant; 1=After bell timeout if zone is restored; 2=when
system is disarmed. Must be "0" for fire or UL Commercial
Burg. installations.
[02]
|
02-15 times 2 hours; 00 disables supervision
[0]
1=16 seconds; 0=no delay. Must be "0" for UL Commercial
Burg. installations.
*89 RESTORE REPORT TIMING
1=enable; 0=disable
[1]
1=continuous; 0=3 beeps
*88 BURG. ALARM COMM. DELAY
[0]
1*31 RF TRANSMITTER CHECK-IN INTERVAL[02]
02-15 times 2 hours; 00 disables transmitter supervision
1*32 RF RECEIVER TYPE
[0]
0=None; 1=4281; 2=5881
1*33 TOUCH-TONE W/ROTARY BACKUP
1=enable; 0=disable
–9 –
[0]
|
1*34 COMM. SPLIT REPORT SELECTION
1*73 PRINTER BAUD RATE 1=300; 0=1200
[0]
0=no; 1=alarms and alarm restores primary, others secondary;
2=open/close, test secondary, others primary; 3 = fire alarms
& troubles primary, all secondary. See ✴51 for comments if
using with dual reporting.
1*42 CALL WAITING DEFEAT
Must be 1200 if using pager interface
1*74 RELAY TIMEOUT XX MINUTES
1=Yes; 0=No.
Enter the relay timeout, 0-127 seconds, desired for #80
Menu
Mode time driven event relay command numbers "05/10"
and #93 Menu Mode Relay Programming command "57".
1=enable; 0=disable When disabled, display lights when
any key is pressed, and turns off after period of keypad
inactivity.
[0]
TAMPER DETECT ENABLE 1=enable; 0=disable. Must
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-16; 00=none. Must be "00" for
Commercial Fire & UL..
[0]
1=enable; 0=disable. Produces quick beeping during exit
delay if enabled.
1*47 CHIME ON BELL 1
1*77 LOG FIRST MAINTENANCE SIGNAL
[0]
0=No Log; 1=Log first maintenance signal from each smoke
detector
[0]
1=enable; 0=disable
3rd Page Programming Fields (press *94)
1*48 WIRELESS KEYPAD ASSIGNMENT
[0]
2*00 NUMBER OF PARTITIONS
0=disable; enter partition in which RF keypad used, 1-8.
Must be "0" for Commercial Fire and UL installations.
1*49 SUPPRESS TX SUPERVISION SOUND
2*01 DAYLIGHT SAVINGS TIME [04, 10]
[1]
1*52 SEND CANCEL IF ALARM + OFF
START/END MONTH
[0]
2*02 DAYLIGHT SAVINGS TIME
|
[1, 5]
2*05 AUTO-ARM DELAY
[0]
Start | End
[15]
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warrning Period begins.
1=50 Hz; 0=60 Hz.
1*57 ENABLE 5800 RF BUTTON GLOBAL ARM [0]
1=enable; 0=disable
2*06 AUTO-ARM WARNING PERIOD
[0]
Enter "1" to enable. If a zone is faulted after pressing button,
console will beep once. User should press button again
within 4 sec. to force bypass those zones. Enter "0" to
disable.
Must be "0" for Commercial Fire and UL installations.
1*60 ZONE 5 AUDIO ALARM VERIFICATION
End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last;
6=next to last; 7=3rd from last [1,5; 1st Sunday in April, last
in Oct.]
[0]
1*58 5800 RF BUTTON FORCE ARM
|
Start
START/END WEEKEND #
1=callback not required; 0=callback required; Must be "0" for
Commercial Fire and UL installations.
1*56 50/60 Hz CLOCK SPEED
|
00-12; if no daylight savings time, enter 00,00
1=no restriction; 0=within bell timeout period only
1*53 DOWNLOAD CALLBACK
[1]
Enter 1-8
1=disable; 0=enable. Must be "0" for Commercial Fire and
UL installations.
1*70
|
1*76 ACCESS CONTROL RELAY FOR PART.[00]
be "0" for Commercial Fire and UL installations.
1*45 EXIT DELAY SOUNDING
| |
1*75 RELAY TIMEOUT YY SECONDS [000]
[0]
1*44 WIRELESS KEYPAD
| |
[000]
Enter the relay timeout, 0-127 in multiples of 2 minutes,
desired for #80 Menu Mode time driven event relay
command numbers "04/09" and #93 Menu Mode Relay
Programming output command "56".
[0]
1*43 PERM. KEYPAD BACKLIGHT
[0]
[15]
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps
every 15 seconds; "ALERT" displayed). Enter 01-15
minutes. 00=instant at end of arming delay .
2*07 AUTO-DISARM DELAY
[15]
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4
minutes; 00=instant at end of window; 15=no auto-disarm.
[0]
Enter 1 If 2-way audio (AAV) is being used; Enter 0 if it is
not.
Must be "0" for Commercial Fire and UL installations.
EVENT LOG TYPES
2*08 ENABLE FORCE ARM FOR AUTO-ARM
[0]
0=disable; 1=enable
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
[1 0 0 0 1 0]
Alrm
Chck
Byps
O/C
Syst
Test
1=enable; 0=disable
1*71 12/24 HOUR TIME STAMP FORMAT
[0]
0=12 hour; 1=24 hour
1*72 EVENT LOG PRINTER ON-LINE
[0]
0=disable; 1=enable
– 10 –
1=enable; 0=disable; If enabled, only openings and closings
occurring outside the scheduled opening/closing windows
will trigger dialer reports. Opening reports will also be
suppressed during the closing window, in order to prevent
false reports when the user arms the system and then
reenters the premises to retrieve a forgotten item.
2*10 ALLOW DISARMING ONLY DURING
3*16 DELAY for ZONE TYPES 17 & 18
[0]
|
[00]
(Waterflow & FIre Supv) Enter 00-15 times 2 seconds
ARMING/DISARMING WINDOWS
0=disable; 1=enable
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
2*11 ALLOW DISARM OUTSIDE WINDOW
3*17 ALTERNATE FUNCTION (TAMPER)
[0]
FOR ZONE 6 0=disabled; 1=enabled
[0]
3*18 EXTENDED DELAY FOR TYPES 17&18
[0]
3*19 ENABLE J2 HEADER PRINTER PORT
[0]
IF ALARM OCCURS
Used only if field 2*10 (partition-specific field) is set to "1". If
this field is enabled ("1") the system can be disarmed
outside the disarm window if an alarm has occurred. If "0",
disarming can only be done during the disarm window. If
field 2*10 is set to "0" for a partition, this field has no effect
for that partition.
2*18 ENABLE GOTO FOR THIS PARTITION
0=pins 5&9 function as per field 3*20; 1=pins 5&9 act as
printer RXD & DTR
3*20 TRIGGER OUTPUTS SELECTION
[0]
1=Allow log-on from other partitions; 0=disable
2*19 USE PARTITION DESCRIPTORS
3*21 MAX # OF DIALER ATTEMPTS
[0]
2*20 ENABLE J2 TRIGGERS by PARTITION
[1]
3*30 DIALER SELECTION
0=disable for displayed partition; 1=enable for displayed
partition
[00000]
F
|
B
| |
P
S
T
3*50 ZONE TYPE RESTORE ENABLES
FOR ZONE TYPES 16-18
16
17 18
1 = enabled; [0 = disabled]
3*55 RESET ON SECOND OFF FOR BELL 1
[0]
[0]
1 = enabled; 0 = disabled
3*56 RESET ON SECOND OFF FOR BELL 2
0=No; 1=Yes.
2*23 DISPLAY BURG & PANIC ALARMS OF
[0]
1=TouchTone; 0=Rotary
OTHER PARTITIONS
[0]
1 = enabled; 0 = disabled
[0]
3*57 BELL 2 & AUX. RELAY CONFIRM
OTHER PARTITIONS
0=No; 1=Yes.
ARM DING
2*24 DISPLAY TROUBLES OF OTHER
Bell 2 AUX.
1=enable; [0=disable] . Must be 1 for UL Commercial
Burglary.
[0]
PARTITIONS
3*59 ENABLE BELL 2 & AUX. RELAY
0=No; 1=Yes.
CHIME ANNUNCIATION
4th Page Programming Fields (press *94)
3*00 DISPLAY TRBL INSTEAD OF CHECK
3*01 FIRE DISPLAY LOCK
3*60 BELL 2 & AUX. RELAY TIMEOUT
[0]
3*61 AUX. RELAY FUNCTION
[1]
[0]
0=Supv. on short/trouble on open; 1=supv. on short or open
3*14 WATERFLOW SILENCE OPTION
|
AUX
[1]
0=Trouble/supervisory; 1=Alarm, silenced by code + OFF
2=Smoke Detector Reset; 3=Battery Save; 4=Alarm,
silenced by code + [#] + 67
0=Check Displayed; 1=Trbl Displayed
3*13 SUPV. N.O./N.C. SELECTION
|
00-15 times 2 minutes; 00=no timeout [00,00] Bell 2
Must be minimum of 16 minutes for UL Burglary
installations.
[0]
3*12 ZN TYPE 18 DELAY USE
Bell 2 AUX
1=enable; [0=disable]
0=scroll all alarms; 1=lock display of first fire alarm.
3*82 ENABLE BURG. FEATURES ON PART. 1
[1]
1=enable; 0=disable; “0” disables AWAY, STAY, MAX,
TEST, INSTANT & CHIME functions
[0]
0=Silence on Code + OFF; 1=Silence when waterflow
restores
0=pulsed; 1=steady
Main Backup
3*31 BACKUP DIALER TOUCHTONE/ROTARY
Used for supervised connection to 7920SE.
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary; S= Silent panic/duress. Enter 1 for
Commercial Burglary and UL.
2*22 DISPLAY FIRE ALARMS OF
[1,0]
1=enabled; 0=disabled
2*21 ENABLE SUPERVISION PULSES FOR LRR
3*15 ALARM BELL SOUND
[8]
1-8 (3, 4 or 5 for NFPA72 compliant systems when a
secondary phone number is programmed (field *34)
0=disable; 1=enable
TRIGGER OUTPUTS
[0]
0= LORRA full connection & Remote Console Sounder;
1=LORRA limited conn. & Keyswitch LEDs; 2=LORRA fire
only conn. & 5140LED
3*85 ENABLE FIRE & SYSTEM ZONE BYPASS [1]
[1,0]
Bell 1Bell 2
– 11 –
0=not enabled; 1=only installer can bypass]; 2=only installer & master
user can bypass. Applies to fire zone types 9, 16, 17 & 18 and system
zones 70-77. Applies to Partition 1 only.
SUMMARY OF PROGRAMMING COMMANDS
•
•
•
•
•
•
•
•
•
•
To enter program mode, enter installer code + [8] + [0] +
[0]
To set standard defaults, press *97
To set communication defaults, press *94 + one of the
following: *80=low speed; *81=Ademco Express;
*82=Ademco High Speed; *83=Ademco's Contact ID
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account & phone number field entries, press
[*] + field number + [*]
To assign zone descriptors, press #93 + follow menu
prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu
prompts
To exit program mode, press *99 OR *98: *99 allows reaccess to programming mode by installer code. *98
prevents re-access to programming mode by installer
code.
– 12 –
Partition-Specific Fields
(Duplicate this page for each partition in the installation.)
To program these fields,
1. Press *91 to select a partition.
2. Enter a partition-specific field number (ex. *09).
3. Make the required entry.
4. Repeat steps 1-3 for each partition in the system.
PARTITION #____ PROGRAM FIELDS
1st Page Fields
*09
*85
ENTRY DELAY #1
|
[02]
FOR PANICS & DURESS
EXIT DELAY #1
*87
|
[03]
ENTRY DELAY #2
*88
00-15 times 15 seconds. Maximum 03 for UL Commercial
Burglary installations.
*12
EXIT DELAY #2
*90
BELL 1 TIMEOUT
CONFIRMATION OF ARMING DING
*23
995 996 999
MULTIPLE ALARMS
QUICK ARM
PRIM. SUBS. ACCT #
|
|
|
PREVENT ZONE XXX BYPASS
[000]
| |
A
B
C
|
D
[0]
[0]
[0]
1=enable; 0=disable
ENABLE OPEN/CLOSE REPORT
[1]
1*52 SEND CANCEL IF ALARM + OFF
1=enable; 0=disable
SWINGER SUPPRESSION
|
1*47 CHIME ON BELL 1
FOR INSTALLER CODE
*84
|
1=enable; 0=disable Produces quick beeping during exit
delay if enabled.
001-128; 000 if all zones can be bypassed
*39
|
1*45 EXIT DELAY SOUNDING
Enter 00-09; B-F (11-15) [15 15 15 15]
*38
[0]
1=enable; 0=disable When disabled, display lights when
any key is pressed, and turns off after period of keypad
inactivity.
[1]
|
[0]
1*43 PERM. KEYPAD BACKLIGHT
1=yes; 0=no
*32
|
Enter speedkey macro # (01-35) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# or 00 to select macro when key is pressed.
[1]
1=yes; 0=no. Enter 1 for Commercial Fire & UL Commercial
Burglary installations.
*29
|
1*26 PANIC BUTTON OR SPEEDKEY
[001]
1=enable; 0=disable
|
[15 15 15 15]
2nd Page Fields
[0]
[00, 00, 00, 00]
KEYPAD PANIC ENABLES
|
SEC. SUBS. ACCT #
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not
1=enable; 0=disable. Must be "1" for UL Commercial
Burglary installations.
*22
|
[0]
1*19 ARMS LOBBY
01-15 times 2 minutes. Minimum 16 minutes for UL.
Commercial Burglary and 6 minutes for Commercial Fire
installations.
*16
BURG. ALARM COMM. DELAY
Enter 1 if this partition affects the common lobby; enter 0 if it
does not.
|
[04]
Duress
[0]
1*18 AFFECTS LOBBY
00-15 times 15 seconds. Maximum 04 for UL Commercial
Burglary installations.
*13
ENTRY WARNING
Enter 00-09; B-F (11-15)
|
[08]
999
1=16 seconds; 0=no delay. Must be "0" for UL Commercial
Burglary installations.
|
[06]
996
1=continuous; 0=3 beeps
00-15 times 15 seconds. Maximum 04 for UL Listed
installations.
*11
995
1=enable; 0=disable
00-15 times 15 seconds. Maximum 03 for UL Listed
installations.
*10
ENABLE DIALER REPORTS[0]
[0]
1=no restriction; 0=within Bell Timeout period only
[03]
|
1*76 ACCESS CONTROL RELAY FOR PART.[00]
01-15 alarms; Must be "00" (disabled) for Commercial Fire &
UL installations..
– 13 –
|
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-16; 00=none. Must be "00" for
Commercial Fire & UL.
2*23 DISPLAY BURG/PANIC ALARMS OF
3rd Page Fields
2*05 AUTO-ARM DELAY
OTHER PARTITIONS
[15]
10=No; 1=Yes
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warrning Period begins.
2*06 AUTO-ARM WARNING PERIOD
[15]
[0]
PARTITIONS
0=No; 1=Yes
3*57 BELL 2 & AUX. RELAY CONFIRM
ARM. DING 1=enable; [0=disable]
Bell 2 Relay
Must be "1" for UL.
[15]
3*59 ENABLE BELL 2 & AUX. RELAY
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4
minutes; 00=instant at end of window; 15=no auto-disarm.
2*08 ENABLE FORCE ARM FOR AUTO-ARM
2*24 DISPLAY TROUBLES OF OTHER
4th Page Fields
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps
every 15 seconds; "ALERT" displayed). Enter 01-15
minutes. 00=instant at end of arming delay .
2*07 AUTO-DISARM DELAY
[0]
CHIME ANNUNCIATION 1=enable; [0=disable]
3*60 BELL 2 & AUX. RELAY TIMEOUT
[0]
00-15 times 2 minutes; 00=no timeout [00,00]
Minimum 16 min. for UL Burglary installations.
0=disable; 1=enable.
Bell 2 Relay
|
Bell 2
|
Relay
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable; If enabled, only openings and closings
occurring outside the scheduled opening/closing windows
will trigger dialer reports. Opening reports will also be
suppressed during the closing window, in order to prevent
false reports when the user arms the system and then
reenters the premises to retrieve a forgotten item.
2*10 ALLOW DISARMING ONLY DURING
•
•
•
[0]
ARMING/DISARMING WINDOWS
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installetion.
0=disable; 1=enable
2*18 ENABLE GOTO FOR THIS PARTITION
SUMMARY OF PROGRAMMING COMMANDS
[0]
•
•
•
•
1=Allow log-on from other partitions; 0=disable
2*20 ENABLE J7 TRIGGERS by PARTITION
[1]
0=disable for displayed partition; 1=enable for displayed
partition
2*22 DISPLAY FIRE ALARMS OF
[0]
•
•
•
OTHER PARTITIONS
0=No; 1=Yes
– 14 –
To enter program mode, enter installer code + [8] + [0] +
[0]
To set standard defaults, press *97
To set communication defaults, press *94 + one of the
following: *80=low speed; *81=Ademco Express;
*82=Ademco High Speed; *83=Ademco's Contact ID
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account & phone number field entries, press
[*] + field number + [*]
To assign zone descriptors, press #93 + follow menu
prompts
To add custom words, press #93 + follow menu
prompts
To enter Installer's Message, press #93 + follow menu
prompts
To exit program mode, press *99 OR *98: *99 allows reaccess to programming mode by installer code. *98
prevents re-access to programming mode by installer
code.
Programming With #93 Menu Mode
NOTE: The following fields should be preset before beginning: 2*00 Number of Partitions; 1*32 receiver
type. In addition, receivers should be programmed via Device programming.
After programming all system related programming fields in the usual way, press #93 while still in programming
mode to display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response
to the displayed menu selection. Pressing 0 will display the next choice in sequence. Menu selections are as
follows:
ZONE PROG?
0=No
1=Yes
For programming the following:
• Zone Number
• Zone Response Type
• Partition Number for Zone
• Dialer report code for zone
• Bell/Aux. relay assignment for zone
• Input Device Type for zone (whether RF, polling loop, etc.)
• Enrolling serial numbers of 5800 series transmitters & serial polling loop devices
into the system.
SEQUENTIAL LEARN?
0=No
1=Yes
For programming the following:
• Input Device Type for zone (whether RF, polling loop, etc.)
• Enrolling serial numbers of 5800 series transmitters & serial polling loop devices
into the system (all other zone characteristics must be pre-programmed).
REPORT CODE PROG?
0=No
1=Yes
For programming the following:
• Alarm report codes for zones
• Restore & supervisory codes
• All other system report codes
ALPHA PROG?
0=No
1=Yes
For entering alpha descriptors for the following:
• Zone Descriptors
• Installer's Message
• Custom Words
• Partition Descriptors
• Relay Descriptors
DEVICE PROG?
0=No
1=Yes
For defining the following device characteristics for addressable devices, including
keypads, RF receivers (4281/5881), output relay modules (4204/4204CF),
4285/4286 VIP Module, ECP long range radio (7820), and vista gateway module:
• Device Address
• Device Type
• Keypad Options (incl. partition assignment)
• RF House ID
• LRR Options (incl. programming radio)
RELAY PROG?
0=No
1=Yes
For defining output relay functions.
RLY VOICE DESCR?
0=No
1=Yes
For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.
CUSTOM INDEX ?
0=No
1=Yes
For creating custom word substitutes for VIP Module annunciation.
CLEAR RF SERIAL#?
1=Yes
0=No
For deleting all RF serial numbers presently in the system, if an undesired
transmitter has been enrolled during sequential enrolling.
– 15 –
#93 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#93
Enters Menu mode
[✱]
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO
1
Press to answer YES
001-009
000
All data entries are either 2-digit or 3-digit entries.
Escapes from menu mode, back into field programming mode, when entered at the first question for
each category.
– 16 –
System Layout Worksheets
As with any security system, you should first define the installation. This includes determining how many partitions
will be used, how many zones per partition, and how many users per partition. You will also need to determine
what peripheral devices will be needed, and basic system options such as exit/entry delays, etc. The control panel
itself should be located in an area that will facilitate wire runs to all partitions, and will allow access to power and
telephone circuits.
To help you lay out a partitioned system, use the following worksheet. This will further simplify the
programming process.
PARTITIONS
Partition #
Descriptor
(4 char max)
Prim.
Sub. #
Sec.
Sub. #
Alpha Default Message
(32 character maximum)
Partition 1
Partition 2
Partition 3
Partition 4
Partition 5
Partition 6
Partition 7
Partition 8
Keyswitch Arming Partition Assignment (1-8 or 9):
Wireless Keypad Partition Assignment (1-8):
Voice Module Partition Assignment (1-8):
Use Partition Descriptor (yes/no)?
Common Lobby Partition Assignment (1-8):
COMMUNICATION OPTIONS BY PARTITION
Option
Part. 1
Part. 2
Swinger Suppression Count 00-15; 00=no suppression
Cancel Report After Disarm
Dialer Reports for Panic (* + 1)
Dialer Reports for Panic (# + 3)
Dialer Reports for Panic (* + #)
Dialer Reports for Duress
Burglary Alarm Communications Delay (16 sec.)
– 17 –
Part. 3
Part. 4
Part. 5
Part. 6
Part. 7
Part. 8
SYSTEM DEFINITIONS BY PARTITION 9enter values or yes/no)
Option
Part. 1
Part. 2
Part. 3
Part. 4
Part. 5
Part. 6
Part. 7
Part. 8
Entry Delay #1 (15-225 seconds):
Exit Delay #1 (15-225 seconds):
Entry Delay #2 (15-225 seconds):
Exit Delay #2 (15-225 seconds):
Quick Arming
Multiple Alarms per Arming
Console Panic for zone 995 (* + 1)
Console Panic for zone 996 (# + 3)
Console Panic for zone 999 (* + #)
Allow Sign-on (GOTO function)
Non-Bypassable Zone*
Sounder Timeout Duration for Bell 1
(2 min. increments)
Sounder Timeout Duration for Bell 2 & Aux Rly
(2 min. increments)
Console Annunciation During Entry**
Console Annunciation During Exit
Confirmation of Arming Ding for Bell 1
Confirmation of Arming Ding for Bell 2 & Aux
Rly
Chime on Bell 1
Chime on Bell 2 & Aux Relay
Access Control Relay (field 1*76)
Affects Lobby (check partitions that apply)
Årms Lobby (check partitions that apply)
Displays Fire Alarms of Other Partitions
Displays Burg & Panic Alarms of Other
Partitions
Displays Troubles of Other Partitions
*Can be any zone 001-128.
**no= 3 beeps yes=continuous
PRINTER OPTIONS
EVENT LOG TYPES
12 or 24 hour Time format
Option
Printer On-Line (yes/no)
Alarm
*1200 or 300 baud Printer Baud Rate
Trouble
Bypass
*Note: Must be 1200 if using pager interface
Open/Close
System
Test
– 18 –
No
Yes
DEVICES (keypads, 4204, rf receivers, vip module, lrr, vgm)
Device
Address
Type
Home
Part
Sound
Opt
Supv
CF?
Keypad
Global
Device
Address
00
16
01
17
02
18
03
19
04
20
05
21
06
22
07
23
08
24
09
25
10
26
11
27
12
28
13
29
14
30
15
31
Type:
0 = Device Not Used
1 = Alpha Console
3 = RF Receiver
4 = Output Relay Module
5 = Voice Module
6 = Long Range Radio
9 = Vista Gateway Module
Type
Home
Part
Sound
Opt
Supv
CF?
Keypad
Global
Console Sounder Options:
00 = No Suppression
01 = Suppress Arm/Disarm and Entry/Exit Beeps
02 = Suppress Chime Mode Beeps Only
03 = Suppress Arm/Disarm, Entry/Exit and Chime Mode Beeps
Defaults:
Addresses 00-01 = Alpha Keypad; No Suppression
– 19 –
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1-3
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
2-Digit
User #
Partition 1
Global
Auth.
Arm?
Level
Open/
Close
2-Digit
User #
Partition 2
Global
Auth.
Arm?
level
Open/
Close
2-Digit
User #
Partition 3
Global
Auth.
Arm?
Level
Open/
Close
Partition 6
Global
Auth.
Arm?
Level
Open/
Close
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 4-6
2-Digit
User #
Partition 4
Global
Auth.
Arm?
Level
Open/
Close
2-Digit
User #
Partition 5
Global
Auth.
Arm?
Level
Open/
Close
2-Digit
User #
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 7-8
Authority Levels:
2-Digit
User #
Partition 7
Global
Auth.
Arm?
Level
Open/
Close
2-Digit
User #
Partition 8
Global
Auth.
Arm?
Level
Open/
Close
1=master (arm, disarm, bypass, and/or modify lower level users)
2=manager (arm, disarm, bypass, and/or modify lower level users)
3=operator A (arm, disarm, bypass)
4=operator B (arm, disarm)
5=operator C (arm, disarm only if system was armed with this code)
6=duress code (arm, disarm, triggers silent panic alarm)
– 20 –
NOTES:
ZONE DEFINITIONS FOR ZONES 001-024
Zone
No.
Zone
Type
Partition
(1-8)
Input
Type
(1-8)
Serial #
Device
Loop
Bell/Relay
Activation
Report
Code
01
02
03
04
05
06
07
08
09
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
– 21 –
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
ZONE DEFINTIONS FOR ZONES 025-048
Zone
No.
Zone
Type
Partition
(1-8)
Input
Type
(1-8)
Serial #
Device
Loop
Bell/Relay
Activation
Report
Code
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
– 22 –
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
ZONE DEFINITIONS FOR ZONES 049-072
Zone
No.
Zone
Type
Partition
(1-8)
Input
Type
(1-8)
Serial #
Device
Loop
Bell/Relay
Activation
Report
Code
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
– 23 –
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
ZONE DEFINTION FOR ZONES 073-096
Zone
No.
Zone
Type
Partition
(1-8)
Input
Type
(1-8)
Serial #
Device
Loop
Bell/Relay
Activation
Report
Code
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
– 24 –
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
ZONE DEFINTION FOR ZONES 097-120
Zone
No.
Zone
Type
Partition
(1-8)
Input
Type
(1-8)
Serial #
Device
Loop
Bell/Relay
Activation
Report
Code
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
– 25 –
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
ZONE DEFINTION FOR ZONES 121-128
Zone
No.
Zone
Type
Serial #
Device
Loop
Input
Type
(1-8)
Partition
(1-8)
Bell/Relay
Activation
Report
Code
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
121
122
123
124
125
126
127
128
ZONE DEFINITIONS FOR KEYPAD PANIC ZONES 995, 996, & 999
Enter yes/no for each partition-field *22
Zone
No.
Zone
Type
1
2
3
4
5
6
7
8
Bell/Rel
Act.
Report
Code
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
995
996
999
ZONE DEFINITIONS FOR SYSTEM ZONES 970-975; 988; 990 & 997
Zone
No.
Zone
Type
Report
Code
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
970
971
972
973
974
975
988
990
997
– 26 –
ZONE DEFINITIONS FOR RELAY SUPERVISORY ZONES 601-616
Zone
No.
Zone
Type
Report
Code
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
Zone
No.
601
617
602
618
603
619
604
620
605
621
606
622
607
623
608
624
609
625
610
626
611
627
612
628
613
629
614
630
615
631
616
632
– 27 –
Zone
Type
Report
Code
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
ZONE DEFINITIONS FOR SUPERVISORY OF ECP DEVICE ZONES 800-831
Zone
No.
Zone
Type
Report
Code
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
Zone
No.
800
816
801
817
802
818
803
819
804
820
805
821
806
822
807
823
808
824
809
825
810
826
811
827
812
828
813
829
814
830
815
831
Zone Types:
00=zone not used
01=entry/exit 1
02=entry/exit 2
03=perimeter
04=interior (follower)
05=day/night burglary
Input Types:
00=not used
01=hardwired
03=supervised RF transmitter
04=unsupervised RF transmitter
05=RF button transmitter
Bells/Auxiliary Relay Activation:
0=none
1=bell 1
2=bell 2
3=bells 1 & 2
06=24 hour silent
07=24 hour audible
08=24 hour auxiliary
09=supervised fire
10=interior (delay)
Zone
Type
Report
Code
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
16=Fire w/Verification
17=Fire Waterflow
18=Fire Supervisory
19=24 hour trouble
20=arm stay
21=arm away
22=disarm
23=no alarm response
27=access control
28=MLB supervision
06=serial number polling loop
07=dip switch type polling loop
08=right loop dip switch polling loop
09=keypad input
10=PassPoint ACS input
4=auxiliary relay
5=bell 1 & auxiliary relay
6=bell 2 & auxiliary relay
7=bells 1 & 2 & auxiliary relay
– 28 –
Output Relays Worksheets
Applicable only if Relays (4204/4204CF) are to be used.
✱
Output Devices – Programmed in the #93 Menu Mode in the Relay Programming Section. Fill in the required
data on the worksheet below and follow the procedure in the installation instructions as you enter the data
during the displays and prompts that appear in sequence.
Note: The Device Programming section must be programmed for the device address. Set the dip switches
on the 4204/4204CF for that address.
S T A R T
OUTPUT
DEV #
(A)
S T O P
either (EV) / (ZL) or (ZT) / (P) or both
either (ZL) or (ZT)/(P) or both
(EV)
(ZL)
(ZL)
(ZT)
(P)
(ZT)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
– 29 –
(P)
1=4204
Dev Add
for 4204
Relay #
for 4204
OUTPUT RELAYS WORKSHEET (cont’d)
S T A R T
OUTPUT
DEV #
(A)
S T O P
either (EV) / (ZL) or (ZT) / (P) or both
either (ZL) or (ZT)/(P) or both
(EV)
(ZL)
(ZL)
(ZT)
(P)
(ZT)
(P)
1=4204
Dev Add
for 4204
Relay #
for 4204
22
23
24
25
26
27
28
29
30
31
32
A = DEVICE ACTION 0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and
off; 4 = Toggle alternately between START and STOP events.
EV = EVENT
0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore
Z L = ZONE LIST
1-8, 0 = Not Used.
"START" ZONE LIST: Upon alarm, fault, or trouble of ANY zone in this list, device
action will START.
"STOP" ZONE LIST: Upon restore of ALL zones on this list, device action will
STOP. It need not be same list as used for START.
ZT = ZONE TYPE/SYSTEM OPERATION
Choices for Zone Types are:
00=Zone Not Used
01=Entry/Exit 1
02=Entry/Exit 2
03=Perimeter
04=Interior (Follower)
05=Day/Night Burglary
06=24 Hour Silent
07=24 Hour Audible
08=24 Hour Auxiliary
09=Supervised Fire
10=Interior (Delay)
16=Fire w/Verification
17=Fire Waterflow
18=Fire Supervisory
19=24 Hour Trouble
23=No Alarm Response
27=Access Control
28=MLB Supervision
NOTE: Any zone in "ZT" for Start, going into alarm, fault, or trouble will activate the relay.
Any zone in "ZT" for Stop, that restores will stop the relay action.
– 30 –
Choices for System Operation are:
20 = Arming-Stay
21=Arm Away
22 = Disarming
30 = On Second Off
31 = End of Exit Time
32 = Start of Entry Time
33 = Any Burglary Alarm
34 = Code + # + 71 Key Entry
35 = Code + # + 72 Key Entry
36 = At Bell Time-out*
37 = 2 Times Bell Time-out*
38 = Chime
39 = Fire Alarm
40 = Bypassing
41 = AC Power Fail
42 = System Battery Low
43 = Communication Failure
44 = RF Low Battery
45 = Polling Loop Failure
51 = RF Receiver Failure
52 = Kissoff
54 = Fire Zone Reset
55 = Disarm + 1 Minute
56 = XX Minutes (enter XX in field 1*74)
57 = YY seconds (enter YY in field 1*75)
58 = Duress
60 = Audio Alarm Verification**
61 = Code + # + 67 Key Entry
62 = Bell 2 Time-out*
63 = Aux. Relay Time-out*
*Or at disarming, whichever occurs first
**Must be selected for both START and STOP operation
P = PARTITION No. 1-8, 0 = Any
ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Relay Programming
Section. Fill in the required data on the worksheet below and follow the procedure in the installation
instructions as you enter the data during the displays and prompts that appear in sequence.
Note: Record desired zone numbers below. More or fewer boxes than shown may be needed, since any list
may include any or all of system's zone numbers.
Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
,
…etc.
,
…etc.
,
…etc.
,
…etc.
,
…etc.
,
…etc.
,
…etc.
,
…etc.
Zone List 2: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 3: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 4: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 5: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 6: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 7: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
,
,
Zone List 8: Started or stopped by zone numbers (enter 00 to end entries).
,
,
,
,
,
,
– 31 –
,
,
Alpha Descriptor Vocabulary
(For Entering Alpha Descriptors. To select a word, press [#] followed by the word's 3-digit number.)
NOTE: This vocabulary is not to be used for relay voice descriptors. See the RELAY VOICE
DESCRIPTORS section when programming relay voice descriptors.
000 (Word Space)
• 001 AIR
• 002 ALARM
003 ALCOVE
004 ALLEY
005 AMBUSH
006 ANTENNA
• 007 AREA
• 008 APARTMENT
009 ART
• 010 ATTIC
011 AUDIO
012 AUX
013 AUXILIARY
• 014 BABY
• 015 BACK
• 016 BAR
017 BARN
• 018 BASEMENT
• 019 BATHROOM
• 020 BED
• 021 BEDROOM
022 BELL
023 BELL 1
024 BELL 2
• 025 BLOWER
• 026 BOILER
027 BOTTOM
028 BOX
029 BREAK
• 030 BUILDING
031 BURNER
032
• 033
034
035
036
037
038
039
040
• 041
042
043
• 044
045
046
047
048
049
• 050
051
CABINET
CALL
CAMERA
CAR
CASE
CASH
CCTV
CEILING
CELLAR
CENTRAL
CIRCUIT
CLIP
CLOSED
COIN
COLD
COATROOM
COLLECTION
COMBUSTION
COMPUTER
CONTACT
• 054
055
• 056
057
058
• 059
060
061
062
• 063
064
• 065
• 066
067
• 068
069
• 070
DEN
DESK
DETECTOR
DIALER 1
DIALER 2
DINING
DISCRIMINATOR
DISPLAY
DOCK
DOOR
DORMER
DOWN
DOWNSTAIRS
DRAWER
DRIVEWAY
DRUG
DUCT
• 071
072
073
074
075
• 076
077
• 078
079
EARTH
EAST
ELECTRIC
EMERGENCY
ENTRY
EQUIPMENT
EXECUTIVE
EXIT
EXTERIOR
• 080
081
082
• 083
• 084
085
• 086
• 087
088
089
• 090
091
• 092
093
094
FACTORY
FAILURE
FAMILY
FATHERS
FENCE
FILE
FIRE
FLOOR
FLOW
FOIL
FOYER
FREEZER
FRONT
FUR
FURNACE
107 HOUSE
108
• 109
110
111
INFRARED
INSIDE
INTERIOR
INTRUSION
112 JEWELRY
• 113 KITCHEN
• 128
129
130
131
• 132
133
• 134
135
136
137
138
• 139
• 140
141
142
164
• 165
166
167
168
169
170
• 171
• 172
173
•
•
MACHINE
MAGNETIC
MAIDS
MAIN
MASTER
MAT
MEDICAL
MEDICINE
MICROWAVE
MONEY
MONITOR
MOTHERS
MOTION
MOTOR
MUD
•
•
•
•
•
•
•
• 143 NORTH
144 NURSERY
• 103 HALL
• 104 HEAT
105 HIGH
106 HOLDUP
210
• 211
212
213
214
PHONE
PHOTO
POINT
POLICE
POOL
POWER
163 QUAD
• 114 LAUNDRY
• 115 LEFT
116 LEVEL
• 117 LIBRARY
• 118 LIGHT
119 LINE
120 LIQUOR
• 121 LIVING
• 122 LOADING
123 LOCK
124 LOOP
125 LORRA
126 LOW
• 127 LOWER
095 GALLERY
• 096 GARAGE
• 097 GAS
098 GATE
• 099 GLASS
100 GROUND
101 GUEST
102 GUN
• 052 DAUGHTERS
053 DELAYED
• 157
158
159
160
161
• 162
• 145
146
• 147
148
• 149
150
151
OFFICE
OIL
OPEN
OPENING
OUTSIDE
OVERFLOW
OVERHEAD
152
• 153
154
• 155
156
PAINTING
PANIC
PASSIVE
PATIO
PERIMETER
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
• 209
RADIO
REAR
RECREATION
REFRIG
REFRIGERATION
RELAY 1
RF
RIGHT
ROOM
ROOF
SAFE
SCREEN
SENSOR
SERVICE
SHED
SHOCK
SHOP
SHORT
SHOW
SIDE
SKYLIGHT
SLIDING
SMOKE
SONIC
SONS
SOUTH
SPRINKLER
STAMP
STATION
STEREO
STORE
STORAGE
STORY
STRESS
STRIKE
SUMP
SUPERVISED
SUPERVISION
SWIMMING
SWITCH
TAMPER
TAPE
TELCO
TELEPHONE
TELLER
TEMPERATURE
•
•
•
•
215
216
217
218
219
220
221
222
223
224
225
226
• 227
• 228
229
• 230
231
THERMOSTAT
TOOL
TRANSMITTER
TRAP
TRIGGERS
ULTRA
UP
UPPER
UPSTAIRS
UTILITY
VALVE
VAULT
VIBRATION
VOLTAGE
WALL
WAREHOUSE
WASH
WEST
WINDOW
WINE
WING
WORK
232 XMITTER
233 YARD
234 ZN-1
• 235 ZONE
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
0
1
1ST
2
2ND
3
3RD
4
4TH
5
5TH
6
6TH
7
7TH
8
8TH
9
9TH
Custom Word 1
to
274 Custom Word 20
CHARACTER (ASCII) CHART
(For Adding Custom Words)
32
33
34
35
36
37
38
39
40
41
(space)
!
"
#
$
%
&
'
(
)
42
43
44
45
46
47
48
49
50
51
*
+
,
.
/
0
1
2
3
52
53
54
55
56
57
58
59
60
61
4
5
6
7
8
9
:
;
<
=
62
63
64
65
66
67
68
69
70
71
– 32 –
>
?
@
A
B
C
D
E
F
G
72
73
74
75
76
77
78
79
80
81
H
I
J
K
L
M
N
O
P
Q
82
83
84
85
86
87
88
89
90
R
S
T
U
V
W
X
Y
Z
Relay Voice Descriptors And Custom Word Substitutes Vocabulary
Word
Index
Air ..................... 116
Alarm ................ 255
And ................... 067
Apartment ......... 117
Appliances ........ 161
Area .................. 118
Attic................... 119
Baby ................. 120
Back.................. 121
Bar .................... 122
Basement ......... 021
Bathroom .......... 051
Battery .............. 053
Bed ................... 092
Bedroom ........... 015
Blower............... 123
Boiler ................ 124
Bright ................ 162
Building ............. 125
Burglary ............ 039
Call ................... 009
Central .............. 089
Chime ............... 054
Closed .............. 126
Computer.......... 127
Console ............ 066
Word
Index
Daughter's ........ 208
Den ................... 052
Detector ............ 128
Device............... 060
Dim ................... 163
Dining ............... 031
Door.................. 016
Down ................ 008
Downstairs........ 184
Driveway........... 130
Duct .................. 131
Word
Index
Front ................. 087
Garage.............. 023
Gas ................... 138
Glass ................ 139
Hall ................... 050
Heat .................. 010
Inside ................ 209
Kitchen.............. 022
East .................. 132
Eight ................. 077
Eighth ............... 221
Equipment ........ 133
Exit.................... 004
Factory.............. 134
Father's............. 211
Fence................ 135
Fifth................... 218
Fire ................... 040
First .................. 136
Five................... 074
Floor ................. 029
Four .................. 073
Fourth ............... 217
Foyer ................ 137
Laundry............. 140
Left.................... 027
Library............... 141
Light.................. 019
Living ................ 030
Loading............. 142
Lower................ 094
Machine ............ 143
Master............... 144
Medical ............. 014
Mother's............ 212
Motion............... 145
Nine .................. 078
Ninth ................. 222
– 33 –
Word
Index
No ..................... 165
North................. 146
Not .................... 012
Off..................... 011
Office ................ 147
On..................... 058
One................... 070
Open................. 148
Outside ............. 210
Panic................. 013
Partition ............ 090
Patio ................. 149
Phone ............... 061
Power ............... 063
Pump ................ 166
Rear ................. 088
Right ................. 028
Room ................ 018
's ....................... 007
Second ............. 056
Service ............. 150
Seven ............... 076
Seventh ............ 220
Shed ................. 151
Shop ................. 152
Word
Index
Side .................. 153
Six .................... 075
Sixth ................. 219
Smoke .............. 024
Son's................. 223
South ................ 155
Stairs ................ 006
Station .............. 156
Storage............. 157
Sun ................... 154
System ............. 062
Temperature..... 158
Third ................. 159
Three ................ 072
Tool .................. 213
Two................... 071
Up..................... 025
Upper................ 187
Upstairs ............ 183
Utility................. 185
West ................. 215
Window............. 017
Wing ................. 216
Zero .................. 069
Zone ................. 002
Scheduling Menu Prompts
To program schedules, enter Scheduling program mode by pressing [Installer Code] + # + 80 to display the first
choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu
selection. Pressing 0 will display the next choice in sequence. Menu selections are as follows:
Time Window ?
1 Yes 0 = No
0
For defining up to 20 time windows each with a start and a stop
time programmed by entering the hours and minutes.
O/C Schedules ?
1 Yes 0 = No
0
For defining the daily open and close schedules for the 8 partitions.
Each partition can be programmed with an opening and closing
window for each day of the week and holidays.
Holidays ?
1 Yes 0 = No
For defining up to 16 holidays for which partitions they apply.
0
Timed Events ?
1 Yes 0 = No
0
Access Sched. ?
1 Yes 0 = No
0
For defining up to 20 time driven events with the following
parameters:
• Time window
• Action desired
• Action specifier
• Activation time
• Days of the week
For defining the limitation of access schedules for the user codes.
Each schedule can be programmed with two window for each day
of the week and holidays
#80 & #81 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#80 or
#81
Enters Menu mode
[✱]
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO
1
Press to answer YES
01-09
00
All data entries are either 2-digit entries.
Escapes from menu mode, back normal operation mode, when entered at the first question for each
category.
— 34 —
Scheduling Worksheets
Time Windows Definitions Worksheet. The system provides 20 time windows that are defined with start and
stop times. They are programmed in the #80 Menu Mode. Fill in the required data on the worksheet below and
follow the procedure in the installation instructions as you enter the data during the displays and prompts that
appear in sequence.
Time Window
Number
Start Time
(HH:MM)
Stop Time
(HH:MM)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
(Keep this worksheet handy, as you will be asked for a given time window number later in this section).
Since the time windows are shared among all partitions, it is important to make sure that changing
a time window does not adversely affect desired actions in other partitions.
Daily Open/Close Schedule Worksheet: Using the time windows previously defined, fill in the required data on
the worksheet below and follow the procedure in the installation instructions as you enter the data during the
displays and prompts that appear in sequence.
Part
Mon
Op
Cl
Tues
Op
Cl
Wed
Op
Cl
Thur
Op
Cl
1
2
3
4
5
6
7
8
— 35 —
Fri
Op
Sat
Cl
Op
Cl
Sun
Op
Cl
Hol
Op
Cl
Holiday Schedule Worksheet: The system provides up to 16 holidays that can be assigned for the system.
Each holiday can be assigned to any combination of partitions. Fill in the required data on the worksheet below
and follow the procedure in the installation instructions as you enter the data during the displays and prompts that
appear in sequence.
HOL
Month/Day
1
/
2
/
3
/
4
/
5
/
6
/
7
/
8
/
9
/
10
/
11
/
12
/
13
/
14
/
15
/
16
/
1
2
Partition
3
4
5
6
7
8
Time-Driven Event Worksheet: The system provides up to 20 time driven events that can be programmed for the
system. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as
you enter the data during the displays and prompts that appear in sequence.
Sched
Num.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Time
Window
Day(s)
M T W T F S S H
Action
Desired
— 36 —
Action
Specifier
Activation
Time
Below is a list of the "Action" codes (desired actions) used when programming time driven events. Note that these
codes are independent of the "relay codes" programmed during the #93 Menu Mode–Relay Programming mode. If
using Time Driven Events to control relays, the following menu items must first be programmed using #93
Menu Mode - Relay Programming:
Enter Relay No.
Relay Group
Restriction
Relay Type
ECP Address
Relay No.
(reference identification number)
(if applicable)
(4204 or none)
if 4204 relays
Relay commands:
Action Specifier for commands 01-05 is Relay #, for commands 06-10 is Relay Group #.
01 = Relay On
03 = Relay Close for 2 seconds
05 = Relay Close YY seconds (field 1*75)
07 = Relay Group Off
09 = Relay Group Close XX minutes (field 1*74)
02 = Relay Off
04 = Relay Close XX minutes (field 1*74)
06 = Relay Group On
08 = Relay Group Close for 2 seconds
10 = Relay Group Close YY seconds (field 1*75)
Arm/Disarm commands:
Action Specifier for commands 20-24 is Partition(s), Activation times 1 (Beginning), 2 (End), 3 (During) are the
only valid choices for auto-arming and disarming functions.
20 = Arm-Stay
22 = Disarm
24 = Force Arm Away (Auto-bypass faulted zns)
21 = Arm Away
23 = Force Arm Stay (Auto-bypass faulted zns)
Bypass commands:
Action Specifier for commands 30-31 is Zone List #, Activation times 1 (Beginning), 2 (End), 3 (During) are the
only valid choices for bypass commands.
30 = Auto bypass - Zone list
31 = Auto unbypass - Zone list
Open/Close Windows:
Action Specifier for commands 40-41 is Partition(s), for 42 is Access Group, and for 50 no specifier is
programmed. Activation time 3 (During) is the only valid choice for these commands.
40 = Enable Opening Window
41 = Enable Closing Window
42 = Enable Access Window
50 = Off-Normal Reminder (Starts local keypad beeping if fire off-normal condition exists)
Activation time:
Refers to when the action is to take place relative to the time window.
1 = Beginning of time window
2 = End of time window
3 = During time window active period only (On at beginning of window, off at end).
4 = Beginning and end of time window (ex. -Coffee break buzzer).
— 37 —
Limitation of Access Worksheet The system provides up to 8 Access Schedules that can be programmed for
the system. Fill in the required data on the worksheet below and follow the procedure in the installation
instructions as you enter the data during the displays and prompts that appear in sequence.
Acc
Sch
Mon
W1
W2
Tues
W1
W2
Wed
W1
W2
Thurs
W1
W2
Fri
W1
Sat
W2
W1
W2
Sun
W1
W2
Hol
W1
W2
1
2
3
4
5
6
7
8
Temporary Schedule #81 Menu Mode The system provides a Temporary Schedule for each partition. Enter
the temporary scheduling mode by pressing [Installer Code] + #81. Fill in the required data on the worksheet
below and follow the procedure in the installation instructions as you enter the data during the displays and
prompts that appear in sequence.
Partition/Windows
1
Mon
Tue
Wed
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
2
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
3
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
4
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 38 —
Thu
Fri
Sat
Sun
5
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
6
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
7
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
8
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 39 —
5800 Series RF Transmitter Loop Designations
LOOP
3
LOOP
2
LOOP
2
(REED)
(REED)
2
1
4
ALTERNATE
POSITION
FOR LOOP 2
5816
ENROLL AS "RF"
(ALWAYS USE)
5802/5802CP
ENROLL AS "BR"
5801
ENROLL AS "UR" OR "RF"
LOOP 1
(TERMINALS)
LOOP 1
(TERMINALS)
LOOP
1
5816MN
ENROLL AS "RF"
LOOP
1
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP 3
(PRIMARY)
LOOP 2
(AUX. CENTER)
LOOP 1
(AUX. RIGHT)
2
3
LOOP
1
LOOP
1
5818
ENROLL AS "RF"
5817
ENROLL AS "RF"
5802MN
ENROLL AS "UR" OR "RF"
5827
SET HOUSE CODE
LOOP
2
5804
ENROLL AS "BR"
(REED)
LOOP 1
(TERMINALS)
LOOP 2
5827BD
SET HOUSE CODE
5819
ENROLL AS "RF"
LOOP 3
(TERMINALS)
LOOP 4
LOOP 3
LOOP
1
LOOP 1
5806/5807/5808
••
•
••
••
• • ••
• •• • ••
••
SET
HOUSE
CODE
(5806 SHOWN)
LOOP
1
LOOP
1
ENROLL AS "RF"
(MOTION)
(MOTION)
5804BD
ENROLL AS "BR"
5849
ENROLL AS "RF"
— 40 —
5890
ENROLL AS "RF"
— 41 —
— 42 —
WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED
TEST BURGLARY SYSTEM WEEKLY
REFER TO INSTRUCTIONS N8988 FOR ADDITIONAL INFORMATION
This equipment should be
installed in accordance
with the National Fire
Protection Association's
Standard 72 (National
Fire Protection Assoc.,
Batterymarch Park,
Quincy, MA. 02269). Printed
information describing proper
installation, operation,
testing, maintenance and
repair service is to be
provided with this equipment.
TYPES OF FIRE SIGNALLING SERVICE:
Manual fire alarm, automatic fire alarm, sprinkler supervisory and waterflow alarm. UL Listed local control (non-coded).
UL Listed central station and remote station protected premises unit when used with 5140DLM back-up dialer module.
Installation limits under jurisdiction of local authority.
WARNING:
THIS UNIT MAY BE PROGRAMMED TO
INCLUDE AN ALARM VERIFICATION
FEATURE THAT WILL RESULT IN A DELAY
OF THE SYSTEM ALARM SIGNAL FROM
THE INDICATED FIRE CIRCUITS. THE
TOTAL DELAY (CONTROL UNIT PLUS
SMOKE DETECTORS) SHALL NOT EXCEED
60 SECONDS. NO OTHER INITIATING
DEVICES SHALL BE CONNECTED TO
THESE CIRCUITS UNLESS APPROVED BY
THE LOCAL AUTHORITY HAVING
JURISDICTION.
J2 VOLTAGE TRIGGERS
See instructions for trigger use and programming
(default functions shown)
1. OUT 4 (SILENT PANIC/DURESS)
2. OUT 7 (TROUBLE)
3. OUT 3 (BURGLARY/AUDIBLE PANIC)
4. OUT 6 (SUPERVISORY)
5. OUT 2 (FIRE)
6. OUT 5 (REMOTE KEYPAD SOUNDER)
7. OUT 1 (OPEN/CLOSE)
8. GROUND
9. IN 1 (N.O. LOOP)
RATINGS: OUT 1, 5, 7:
LOW: 2K TO GROUND
HIGH: 10 - 14VDC, 20mA MAX
OTHER OUTS: LOW: 1K TO GROUND
HIGH: 10 - 14VDC THRU 5K
Attach 5140DLM module to main PCB shield using
4 standoffs (supplied)
The 5140DLM Dialer
Complies with FCC Rules, Part 68
BACK-UP LINE SEIZE
FCC Reg. No.: AC398U-68628-MO-N
LED (GREEN)
Ringer Equivalence: 0.7B
BACK-UP PHONE JACK
SEE TELCO
JACK SHOCK
RJ31X
WARNING
BELOW
Connect to main PCB
header J3 using ribbon
cable (supplied)
CIRCUIT CONTROL UNIT SMOKE DETECTOR
DELAY-SEC MODEL DELAY-SEC
(ZONE)
(connect using supplied cable)
Supervision is programmable
BACK-UP DIALER ON HOOK
VOLTAGE THRESHOLD (BLUE)
INTACT: 25V
CUT: 13V
BACK-UP DIALER EARTH
GROUND SCREW
(wire to main PCB
terminal #30)
VOLTAGE
TRIGGERS
(not supervised)
OPTIONAL 5140DLM BACK-UP DIALER MODULE
BLK
+
THE DELAY TIME MARKED ON THE INSTALLED
DETECTOR(S) IS TO BE USED
RED
OPTIONAL REMOVABLE
TERMINAL BLOCK KIT:
ADEMCO NO. 4142BLK
BELL OUTPUTS
TRNSFMR
1
2
3
4
5
7
8
9
J4 KEYPAD PORT #2
See instr. regarding port #2 use
1. GROUND (to keypad black wire)
4. DATA IN 2 (to keypad green wire)
5. AUX PWR #2 (to keypad red wire)
Rating: 10 - 14 VDC,
400mA max. See note 1
7. DATA OUT 2 (to keypad yellow wire)
KEYPAD PORT #2
1
2 3 4
5
6 7 8
9
J4
Make connections using
4142TR cable (supplied)
(not supervised)
AUX. RELAY
6
PINS 2, 3, 6, 8 & 9 NOT USED
KEYPAD PORT #1
10
11
12
13
ZONE 1
14
15
ZONE 2
16
17
ZONE 3
18
19
NOTES
NOTE 1:
The combined standby current
drawn from aux pwr #1, aux pwr #2
and polling loop cannot exceed
1.0A.The combined alarm current
drawn from aux pwr #1, aux
pwr #2, polling loop, bell 1 and
bell 2 cannot exceed 2.3A.
NOTE 2:
2k EOLR is Ademco model 610-7
NOTE 3:
See instructions on setting
addresses & for max # of keypads
and wire run length restrictions.
Keypad color subject to approval
of local authority.
Each output may be selected for
Style Y supervision or no supervision
(See main PCB jumpers W1, W4 and
program field 3*10)
FIRE CKTS: Supervise using 2k EOLR.
Use polarized sounding devices.
BURG CKTS: Supervision not req'd.
EOLRs not req'd. May use non
polarized devices.
Ratings: 10 - 14VDC, 1.7A max.
See note 1, see instructions
for compatible devices.
For commercial fire, bell timeout
must be a minimum of 6 minutes.
ALL CIRCUITS ARE POWER LIMITED EXCEPT
THE OUTPUT OF THE 1451 TRANSFORMER
20
SMOKE
N.C.
N.C.
+
N.C.
N.C.
N.C.
N.C.
+
2-WIR
DETE E GLASS B
CTOR
R
LOOP EAK
+
PROG
AS KE RAMMABL
E
Y SWIT
CH LO
OP
+
+
SMOKE
PROG
AS TA RAMMABL
E
MPER
LOOP
2-W
DET IRE SMO
ECT
OR LKE
OO
+
+
POLLING
LOOP
+
GLASS
BREAK
N.C.
+
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
2k
2k
2k
2k
2k
2k
N.C.
J2
WARNING:
TO PREVENT
RISK OF
ELECTRICAL
SHOCK,
DISCONNECT
TELCO JACK
BEFORE
SERVICING
THIS PANEL
EARTH GROUND
See instructions for
proper earth ground
connections
N.O.
ZONE 1-8 NOTES
• All zones provide Style B supervision
• Ratings for zones 1,2:
• Zone resistance (excluding EOLR):
- 10 - 14VDC
- Zones 1, 2, 8: 100 ohms max
- 2mA max for smoke det. (up to 16 detectors
- Other zones: 300 ohms max
of the type specified in the instructions
• Zone response: 350 - 500mS (all zones)
can be used)
• UL compatibility ID: A
Do not mix fire and burg. sensors on one loop.
N.C. contacts for burg. usage only.
VISTA-128FB
SUMMARY OF CONNECTIONS
9
4209U
4192SD
SMOKE
2k (note 2)
6 7 8
PHONE JACK
P
P
Red Blk Grn Yel
REMOTE KEYPADS:
6139, 6139R
SEE NOTE 3
AUX RELAY (FORM C)
programmable response
(not supervised)
HORN
HORN
Contact Rating:
28V, 2.8A
AUXILIARY POWER #1
resistive loads
Rating: 10 - 14VDC
1.0A MAX (STANDBY)
1.7A MAX (ALARM)
2k (note 2)
2k
See note 1.
ALARM POLARITY SHOWN
(not supervised)
+
Data out
+
Data in
LE
N.C
BELL
.
BELL
+
2-W
DET IRE SMO
ECT
OR LKE
OO
BL
BELL 2
+
.
SP
PO ARE
WR AU
#1 X
BL
TRANSFORMER
W/ENCLOSURE
ADEMCO No.1451 WH
BLACK
(supplied)
INPUT: 120VAC,
INPUT
60HZ,
1.0A max. Connect to a
dedicated circuit.
OUTPUT: 18VAC
72VA
BELL 1
PO
OUTPUT
5
CONNECTION OF THE FIRE ALARM
SIGNAL TO A FIRE ALARM HEADW6
QUARTERS OR A CENTRAL STATION
(BLUE)
SHALL BE PERMITTED ONLY WITH
INTERFACE
TO
5140DLM
THE APPROVAL OF THE LOCAL
AUTHORITY HAVING JURISDICTION.
J3
THE BURGLARY ALARM SIGNAL
SHALL NOT BE CONNECTED TO A
POLICE EMERGENCY NUMBER.
MAIN
Connect
RJ31X using
ZONE 5 ZONE 6
ZONE 7 ZONE 8
RJ31X cable supplied.
Supervision is
21
22
23
24
25
26
28
29
30
27
programmable
ZONE 4
AC WIRING IS
SUPERVISED
N.O
— 43 —
BELL CIRCUIT SUPERVISION JUMPERS
INTACT: Supervised using 2k EOLR
Connect to 12V, 12AH min/34.4AH max
CUT: Not supervised (no EOLR used)
lead acid batteries using cables supplied.
BELL 1
BELL 2
See instructions for required capacity.
Float charging voltage: 13.7VDC. Battery
normally need not be replaced for
W1
W4
at least 3 yrs.
(WHITE) (WHITE)
2 3 4
Make connections using
4142TR cable (not supplied)
MAIN DIALER ON HOOK
VOLTAGE THRESHOLD
INTACT:25V
CUT: 13V
MAIN PCB SHIELD
BATTERY TABS
1
2k
4208U
TO OTHER DEVICES
Polling Loop
Ratings:
(supervised)
128mA max. See note 1.
See instructions for
compatible devices
and for max wire
run length
The VISTA-128 Main Dialer
Complies with FCC Rules, Part 68
FCC Reg. No.: AC398U-68192-AL-E
Ringer Equivalence: 0.7B
165 Eileen Way Syosset, NY, 11791
Copyright  1998 PITTWAY Corporation
¬9)%35l
V128FB-PR 5/98
Download PDF