Lampak UFO-3AW Installation Instructions

Lampak UFO-3AW Installation Instructions
UFO-3AW
INSTALLATION INSTRUCTIONS
! IMPORTANT SAFEGUARDS !
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent high voltage from being present on red & yellow output leads prior to installation,
battery connector must be open. Do not join battery connector until installation is complete and
AC power is supplied to the emergency ballast.
2. This product is for use with most 32 W through 40 W T8, T10 or T12 single pin or bipin fluorescent
lamps, including energy saving, circline, U-shaped and rapid-start (4-pin) long compact
fluorescent lamps.
3. Make sure all connections are in accordance with the National Electrical Code and any local
regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and
battery connector of the emergency ballast before servicing.
5. This emergency ballast is for factory or field installation in either the ballast channel or on top of
the fixture.
6. This product is suitable for damp locations where the ambient temperature is 0°C minimum,
+55°C maximum. Product is not suitable for heated air outlets and wet or hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field
replaceable. Contact the manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
CAUTION: Verify that all replacement lamp types marked on the installed luminaire are also identified
as suitable for use with this inverter/charger pack.
SAVE THESE INSTRUCTIONS
CONTAINS NICKEL-CADMIUM
RECHARGEABLE BATTERY.
MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Ni - Cd
WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
09/27/13
©
Hubbell Lighting, Inc. • 701 Millennium Blvd • Greenville, SC 29607 • (864) 678-1000 • FAX (864) 678-1415 • www.dual-lite.com
443529060391
INSTALLATION
WARNING: TO PREVENT HIGH VOLTAGE from being present ON RED & YELLOW
OUTPUT LEADS PRIOR TO INSTALLATION, battery CONNECTOR MUST BE OPEN. do
not JOIN battery CONNECTOr until INSTALLATION is complete and Ac power
is supplied to the emergency ballast.
NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of power is
required. The emergency ballast must be fed from the same branch circuit as the AC ballast.
1. Disconnect AC power from the fixture. Remove the ballast channel cover and install the emergency ballast
either in the ballast channel (see Illustrations 1 & 2) or on top of the fixture* (see Illustration 3).
2. Select the appropriate wiring diagram to connect the emergency ballast to the AC ballast and lamp. Make sure
all connections are in accordance with the National Electrical Code and any local regulations.
ILLUSTRATION 1
ILLUSTRATION 2
ILLUSTRATION 3
*For installation on top of the fixture, wire bundle covers may be required by state or local codes. These covers are available from the
manufacturer
as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete infomation.
3. Install the test switch through the ballast channel cover of a troffer or through the side of a strip fixture. Drill a
1/2" hole and install the switch as shown (see Illustration 1 & 2). Refer to the wiring diagrams section and wire
the test switch so it removes AC power from the unswitched hot line to the emergency ballast.
4. Refer to Illustration 4 and install the charging indicator light so that it will be visible after the fixture is installed.
NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. If
a detached charging indicator light is used, connect by matching wire colors and install as shown
in Illustration 4.
5. In a readily visible location, attach the label “CAUTION–This Unit Has More Than One Power Connection
Point. To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And
Emergency Power Supplies Before Servicing.”
2
ILLUSTRATION 4
TROFFER STYLE FIXTURE
STRIP STYLE FIXTURE
Fixture
Fixture
Emergency
Ballast
Leads to Charging
Indicator Light
Ballast
Channel
Cover
Charging
Indicator
Light
Charging
Indicator
Light
7/8” Bushing
Inserted into
Ballast Channel
Cover
7/8” Punch
Plastic Tubing
(please cut to
necessary
length)
1/2” White Bushing
to Hold Charging
Indicator Light
Charging Indicator Light
Violet (+)
Brown (–)
Brown (–)
5/8" Black
Bushing
1/2" White
Bushing
Fixture Lens
Violet (+)
1/2" White
Bushing
5/8" Black
Bushing
1/2" Punch
* If violet and brown leads are detached, connect to
unit by matching wire colors.
NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label.
6. After installation is complete, supply AC power to the emergency ballast and join the inverter connector.
7. A short-term discharge test may be conducted after the emergency ballast has been charging for one hour.
Charge for 24 hours before conducting a long-term discharge test. Refer to OPERATION.
OPERATION
When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged.
When power fails, the emergency ballast automatically switches to emergency power, operating one lamp at
reduced illumination. When AC power is restored, the emergency ballast returns to the charging mode and delays AC
ballast operation for approximately three seconds to prevent false-tripping of AC ballast (end-of-lamp-life) shutdown
circuits. This emergency ballast will operate the rated lamp load for a minimum of 90 minutes.
MAINTENANCE
Although no routine maintenance is required to keep the emergency ballast functional, it should be checked
periodically to ensure that it is working. The following schedule is recommended:
1. Visually inspect the charging indicator light monthly. It should be illuminated.
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One lamp should operate at reduced illumination.
3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced illumination for at
least 90 minutes.
Refer any servicing indicated by these checks to qualified personnel.
3
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT.
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.
WIRING DIAGRAMS for 1-LAMP emergency operation
FIG A
ONE (1) LAMP INSTANT START BALLAST
FIG B
ONE (1) LAMP RAPID START BALLAST
WALL SWITCH
WALL SWITCH
HOT
WHT/RED
B
L
K
RED
INVERTER
CONNECTOR
TEST
SWITCH
WHITE
VIOLET
CHARGING
INDICATOR
LIGHT
B
L
K
BROWN
(CAP UNUSED LEAD)
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
HOT
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
BLU/WHT
BLUE
BLUE
(CAP UNUSED LEAD)
RED
1 LAMP
INSTANT
START
BALLAST
WHITE
VIOLET
BROWN
BLACK 120V
OR
ORANGE 277V
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
BLU/WHT
BLUE
BLUE
BLUE
WHT/BLK
BLK
BLK
WHT
FIG D
RED
WHITE
VIOLET
CHARGING
INDICATOR
LIGHT
BROWN
(CAP UNUSED LEAD)
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
TEST
SWITCH
YEL/BLK
BLU/WHT
BLUE
INVERTER
CONNECTOR
CHARGING
INDICATOR
LIGHT
B
L
K
BLUE
BLUE
2 LAMP
INSTART
START
BALLAST
(CAP UNUSED LEAD)
LAMP 2
WHITE
VIOLET
BROWN
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
RED
RED
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
BLU/WHT
BLUE
BLUE
BLUE
WHT/BLK
RED
INVERTER
CONNECTOR
WHITE
VIOLET
CHARGING
INDICATOR
LIGHT
BROWN
(CAP UNUSED LEAD)
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
FIG F
YELLOW
YEL/BLK
WHT/RED
B
L
K
LAMP 1 (EMERGENCY)
BLU/WHT
TEST
SWITCH
B
L
K
BLUE
BLUE
BLUE
3 LAMP
INSTANT
START
BALLAST
LAMP 2
BLUE
WHITE
VIOLET
CHARGING
INDICATOR
LIGHT
BROWN
(CAP UNUSED LEAD)
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
RED
WHITE
VIOLET
BROWN
BLACK 120V
OR
ORANGE 277V
WHITE
LAMP 3
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
LAMP 1 (EMERGENCY)
YEL/BLK
BLU/WHT
BLU/WHT
BLU/WHT
BLUE
BLUE
BLUE
YELLOW
YELLOW
3 LAMP
RAPID
START
BALLAST
WHT/BLK
RED
BLK
RED
WHT
WHT
RED
FIG H FOUR (4) LAMP RAPID START BALLAST
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
HOT
LAMP 1 (EMERGENCY)
YELLOW
BLU/WHT
WHT/RED
B
L
K
TEST
SWITCH
YEL/BLK
YELLOW
B
L
K
BLUE
BLUE
BLUE
4 LAMP
INSTANT
START
BALLAST
RED
WHT
LAMP 2
RED
INVERTER
CONNECTOR
CHARGING
INDICATOR
LIGHT
(CAP UNUSED LEAD)
COMMON
LAMP 3
RED
WHITE
VIOLET
BROWN
BLACK 120V
OR
ORANGE 277V
WHITE
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
LAMP 1 (EMERGENCY)
YEL/BLK
YELLOW
YELLOW
BLU/WHT
RED
BLUE
RED
LAMP 4
BLU/WHT
4 LAMP
RAPID
START
BALLAST
WHT/BLK
YELLOW
BLK
ONE (1) 32-40 W LAMP WITHOUT AC BALLAST
CAP
TEST
SWITCH
B
L
K
WHITE
VIOLET
CHARGING
INDICATOR
LIGHT
BROWN
(CAP UNUSED LEAD)
BLACK 120V
OR
ORANGE 277V
WHITE
COMMON
CAP
RED
WHT/RED
RED
INVERTER
CONNECTOR
E
MB
EA
RL
GL
EA
NS
CT
Y
YELLOW
LAMP
YEL/BLK
BLU/WHT
CAP
BLUE
CAP
WHT/BLK
4
BLU/WHT
LAMP 2
LAMP 3
BROWN
BROWN
BLK
BLUE
WHT
BLUE
WIRING DIAGRAMS for Emergency-Only fixtures
B
L
K
LAMP 3
BLK
WHT/BLK
HOT
LAMP 2
WALL SWITCH
WHT/RED
RED
CHARGING
INDICATOR
LIGHT
COMMON
FOUR (4) LAMP INSTANT START BALLAST
INVERTER
CONNECTOR
INVERTER
CONNECTOR
(CAP UNUSED LEAD)
WALL SWITCH
HOT
FIG I YELLOW
THREE (3) LAMP RAPID START BALLAST
HOT
RED
E
MB
EA
RL
GL
EA
NS
CT
Y
WHT/BLK
B
L
K
YELLOW
WALL SWITCH
WHT/RED
TEST
SWITCH
LAMP 2
WHT
THREE (3) LAMP INSTANT START BALLAST
HOT
B
L
K
RED
BLK
WALL SWITCH
FIG G
RED
2 LAMP
RAPID
START
BALLAST
BLK
B
L
K
LAMP 1 (EMERGENCY)
YEL/BLK
WHT
TEST
SWITCH
RED
TWO (2) LAMP RAPID START BALLAST
WHT/RED
B
L
K
LAMP 1 (EMERGENCY)
WHT/BLK
B
L
K
RED
1 LAMP
RAPID
START
BALLAST
WHT
HOT
WHT/RED
FIG E
LAMP
YEL/BLK
WALL SWITCH
INVERTER
CONNECTOR
B
L
K
RED
WHITE
COMMON
TWO (2) LAMP INSTANT START BALLAST
HOT
TEST
SWITCH
CHARGING
INDICATOR
LIGHT
B
L
K
WALL SWITCH
B
L
K
INVERTER
CONNECTOR
TEST
SWITCH
WHT/BLK
FIG C
WHT/RED
B
L
K
LAMP
YEL/BLK
LAMP 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising