Epson | C84 | Stylus C80N / C84 - Start Here Card

EPSON Stylus C84
2 Power On
1
EPSON Stylus C84
®
Start
Here
Close the cartridge cover.
6
Press the ink button and close the
printer cover.
Connect the printer’s power cord to the printer, then
plug it into a standard electrical outlet.
The green power light flashes as your
printer charges ink for several seconds.
2
Press the printer’s power
button until the green
power light comes on.
CAUTION: Don’t turn off the printer
while the green power light is
flashing, unless the printer hasn’t
moved or made any noise for more
than 5 minutes.
Power button
CAUTION: Use only the printer’s
power button to turn the printer on or off.
3 Install Ink Cartridges
1
1 Unpack
4 Connect the Printer
Printer cables are not included with your printer. You need only one of the
following cables:
• USB cable (Windows® or Macintosh®) or
• Parallel cable (Windows only).
NOTE: If you have Windows NT 4.x, you must use a parallel cable.
Lower the printer’s output tray, pull
out the extension and open
the cover.
CPD-16675R1
4043482-00
XXX
1
5
USB Cable Users (Windows or Mac )
®
2
Remove everything from the box.
1
Make sure your computer is turned off. Keep it turned off until section 6,
“Install Software.”
2
Plug the
of the printer.
3
Plug the
flat end of the cable into your computer’s USB port until it stops.
(You can use any open USB port.)
square end of the cable into the USB port on the back
Shake the package of ink cartridges four or five times. Then remove the cartridges
from the package. (Don’t shake them after removing the packaging.)
Paper support
Don’t touch the
green circuit boards
or remove any labels
Printer
Flat end
Manual
Square end
CD-ROM
Power cord
2
3
Ink cartridges
Open the cartridge cover.
Parallel Cable Users (Windows only)
Remove all the blue tape and packing material inside and around the printer.
The tape may be in slightly different places on your printer, so check carefully.
Don’t touch
this cable
1
Make sure your computer is turned off. Keep it turned off until section 6, “Install
Software.”
2
Plug the end of the cable with the slotted connector into the parallel port on the side
of the printer, then secure it with the wire clips.
3
Plug the end of the cable with the screws on the side into your computer’s
parallel port and secure it.
Remove this piece
4
3
Slide the paper support into the
groove on the back of the sheet feeder.
The paper support should
fit securely.
Lower each ink cartridge into its
holder with the green circuit board
facing the front.
Then gently push each ink
cartridge down until it is firmly
seated.
The color of the cartridge label
should match the marker on
the holder.
End with screws
continue
Slotted end
Turn over
EPSON Stylus C84
2 Power On
1
EPSON Stylus C84
®
Start
Here
Close the cartridge cover.
6
Press the ink button and close the
printer cover.
Connect the printer’s power cord to the printer, then
plug it into a standard electrical outlet.
The green power light flashes as your
printer charges ink for several seconds.
2
Press the printer’s power
button until the green
power light comes on.
CAUTION: Don’t turn off the printer
while the green power light is
flashing, unless the printer hasn’t
moved or made any noise for more
than 5 minutes.
Power button
CAUTION: Use only the printer’s
power button to turn the printer on or off.
3 Install Ink Cartridges
1
1 Unpack
4 Connect the Printer
Printer cables are not included with your printer. You need only one of the
following cables:
• USB cable (Windows® or Macintosh®) or
• Parallel cable (Windows only).
NOTE: If you have Windows NT 4.x, you must use a parallel cable.
Lower the printer’s output tray, pull
out the extension and open
the cover.
CPD-16675R1
4043482-00
XXX
1
5
USB Cable Users (Windows or Mac )
®
2
Remove everything from the box.
1
Make sure your computer is turned off. Keep it turned off until section 6,
“Install Software.”
2
Plug the
of the printer.
3
Plug the
flat end of the cable into your computer’s USB port until it stops.
(You can use any open USB port.)
square end of the cable into the USB port on the back
Shake the package of ink cartridges four or five times. Then remove the cartridges
from the package. (Don’t shake them after removing the packaging.)
Paper support
Don’t touch the
green circuit boards
or remove any labels
Printer
Flat end
Manual
Square end
CD-ROM
Power cord
2
3
Ink cartridges
Open the cartridge cover.
Parallel Cable Users (Windows only)
Remove all the blue tape and packing material inside and around the printer.
The tape may be in slightly different places on your printer, so check carefully.
Don’t touch
this cable
1
Make sure your computer is turned off. Keep it turned off until section 6, “Install
Software.”
2
Plug the end of the cable with the slotted connector into the parallel port on the side
of the printer, then secure it with the wire clips.
3
Plug the end of the cable with the screws on the side into your computer’s
parallel port and secure it.
Remove this piece
4
3
Slide the paper support into the
groove on the back of the sheet feeder.
The paper support should
fit securely.
Lower each ink cartridge into its
holder with the green circuit board
facing the front.
Then gently push each ink
cartridge down until it is firmly
seated.
The color of the cartridge label
should match the marker on
the holder.
End with screws
continue
Slotted end
Turn over
EPSON Stylus C84
2 Power On
1
EPSON Stylus C84
®
Start
Here
Close the cartridge cover.
6
Press the ink button and close the
printer cover.
Connect the printer’s power cord to the printer, then
plug it into a standard electrical outlet.
The green power light flashes as your
printer charges ink for several seconds.
2
Press the printer’s power
button until the green
power light comes on.
CAUTION: Don’t turn off the printer
while the green power light is
flashing, unless the printer hasn’t
moved or made any noise for more
than 5 minutes.
Power button
CAUTION: Use only the printer’s
power button to turn the printer on or off.
3 Install Ink Cartridges
1
1 Unpack
4 Connect the Printer
Printer cables are not included with your printer. You need only one of the
following cables:
• USB cable (Windows® or Macintosh®) or
• Parallel cable (Windows only).
NOTE: If you have Windows NT 4.x, you must use a parallel cable.
Lower the printer’s output tray, pull
out the extension and open
the cover.
CPD-16675R1
4043482-00
XXX
1
5
USB Cable Users (Windows or Mac )
®
2
Remove everything from the box.
1
Make sure your computer is turned off. Keep it turned off until section 6,
“Install Software.”
2
Plug the
of the printer.
3
Plug the
flat end of the cable into your computer’s USB port until it stops.
(You can use any open USB port.)
square end of the cable into the USB port on the back
Shake the package of ink cartridges four or five times. Then remove the cartridges
from the package. (Don’t shake them after removing the packaging.)
Paper support
Don’t touch the
green circuit boards
or remove any labels
Printer
Flat end
Manual
Square end
CD-ROM
Power cord
2
3
Ink cartridges
Open the cartridge cover.
Parallel Cable Users (Windows only)
Remove all the blue tape and packing material inside and around the printer.
The tape may be in slightly different places on your printer, so check carefully.
Don’t touch
this cable
1
Make sure your computer is turned off. Keep it turned off until section 6, “Install
Software.”
2
Plug the end of the cable with the slotted connector into the parallel port on the side
of the printer, then secure it with the wire clips.
3
Plug the end of the cable with the screws on the side into your computer’s
parallel port and secure it.
Remove this piece
4
3
Slide the paper support into the
groove on the back of the sheet feeder.
The paper support should
fit securely.
Lower each ink cartridge into its
holder with the green circuit board
facing the front.
Then gently push each ink
cartridge down until it is firmly
seated.
The color of the cartridge label
should match the marker on
the holder.
End with screws
continue
Slotted end
Turn over
5 Load Paper
1
2
Fan a few sheets of paper and
place them against the right
edge guide. Make sure the
paper is under the tabs on the
edge guides. Don’t push the
paper in.
5
You see a screen asking where you want Windows to search. Click CD-ROM drive.
Then click Next.
6
Click Next on the following screen.
7
When installation halts, click Finish.
8
Your computer detects your printer connection a
second time. Do one of the following:
Me
Press in the side of the left
edge guide and slide it against
the paper, but not too tightly.
Don’t load paper
above this arrow
98
6 Install Software
Follow the appropriate section below to install the printer software on Windows XP,
Windows Me, Windows 98, Windows 2000, or Macintosh.
For instructions on installing the software on Windows NT 4.x, see your Printer Basics book.
NOTE: To print from Macintosh Classic applications as well as OS X applications,
follow the steps below in OS X, then restart your Macintosh in OS 9 and follow the
steps below again.
Click Next on the next screen. The Add Printer Wizard screen appears.
Click Finish.
Click Next on each of the four screens that follow. The Add Printer Wizard appears.
Click Finish.
9
At the final Add New Hardare Wizard screen,
click Finish.
10
You see the license agreement. Read the agreement and click Agree.
NOTE: If the license agreement doesn’t appear, double-click the
CD-ROM icon, then double-click
EPSON.
Make sure your printer is on, then turn on your Macintosh. When you see your Macintosh
icons on the desktop, insert the CD-ROM in the CD-ROM or DVD drive.
2
If the CD-ROM window doesn’t open automatically, double-click the
EPSON CD-ROM icon.
3
Double-click
4
Read the License Agreement and click Agree.
5
At the Main Menu, click Install Printer Driver.
In Mac OS X, enter your administrator password
and click OK.
6
Follow the instructions on the screen and then restart
your computer.
7
Double-click the
CD Icon or
EPSON
CD-ROM icon again (if necessary), then double-click the
You see the Options Menu. Continue with the instructions below under “Finishing Windows
Installation” to complete your software installation.
Windows 2000
1
Turn on your computer. (Make sure your printer is still on.)
1
Turn on your computer. (Make sure your printer is still on.)
Wait for this screen to appear.
2
Wait until you see the Found New Hardware Wizard screen. Then put the EPSON
CD-ROM in your drive.
3
After a moment, click Next. You see a screen indicating
that Windows has found an unknown device.
4
Click the Search for option, then click Next.
NOTE: If you don’t see the Found New
Hardware screen, make sure your printer
is on and your cable is securely connected
to your printer’s port.
1
CD Icon or
EPSON.
EPSON
Windows XP
2
Macintosh
EPSON installer icon.
8
Optionally, click Install EPSON Software Film Factory and then click Install. Follow the
instructions on the screen.
9
Click Install Manual and Printer Movies to install the EPSON Printer Information Center.
NOTE: You need a browser – such as Microsoft Internet Explorer 4.0 or later or
Netscape Navigator® 4.0 or later – to view the guide.
10
When you’re done, click Exit to close the installer. You see the EPSON Product
Registration screen.
11
Register your printer as instructed. At the last screen, click Done or close your browser.
Then remove the CD-ROM.
3
Put the EPSON CD-ROM in your drive.
5
Make sure CD-ROM drives is selected, then click Next.
4
Wait while the files are copied to your computer.
6
At the next screen, click Next. Wait while the files are copied to your computer.
5
Click Finish when you see the final Found New Hardware Wizard screen.
7
Click Finish when you see the final Found New Hardware Wizard screen.
Add Your Printer in Mac OS X
6
You see the license agreement. Read the agreement and click Agree.
8
You see the license agreement. Read the agreement and click Agree.
1
Open the Applications folder on your hard drive, then open the Utilities folder and
double-click Print Center.
2
Choose Stylus C84 in the printer list and click the
You see the Options Menu. Continue with the “Finishing Windows Installation” instructions
to the right to complete your software installation.
You see the Options menu. Continue with the “Finishing Windows Installation” instructions to
complete your software installation.
Windows Me and 98
Finishing Windows Installation
1
1
Turn on your computer. (Make sure your printer is still on.) Wait until you see the
Add New Hardware Wizard.
2
3
Windows Me
Put the EPSON CD-ROM in your drive.
3
After a moment, click Next on the Add New Hardware Wizard screen. (In Windows
Me, you may not need to click Next.)
4
Me
98
If you’re running Windows 98,
continue with step 4.
Optionally, click Install EPSON Software
Film Factory and follow the on-screen instructions.
Click Install Manual and Printer Movies and follow
the on-screen directions to install the EPSON Printer
Information Center on your desktop.
Windows 98
2
If you’re running Windows Me,
go to step 7.
When you see this screen, make sure you have
paper in the printer, then click Print a Test Page
to check that your printer is set up correctly.
If you are using Mac OS X, add all your printer’s page setup options as described under “Add Your
Printer in Mac OS X.” If you are using Mac OS 9 or earlier, select your printer in the Chooser as
described under “Choose Your Printer in Mac OS 9 or earlier.”
Add icon.
NOTE: If you don’t see your printer in the Printer List, make sure the printer is
turned on and connected. Also make sure EPSON USB is selected.
3
Click the Stylus C84 icon to select it, then
choose All from the Page Setup menu.
4
Click Add. You see the Printer List with the
Stylus C84 and Stylus C84 (Sheet Feeder Borderless) printer options.
5
Choose EPSON USB
Choose All
Close Print Center.
Click Add
4
When you’re finished, click Exit to close the Options Menu.
You’re ready to start printing! See the details in
your Printer Basics book.
5
When you see the EPSON Product Registration screen, register your
printer as instructed, then remove your CD-ROM.
Choose Your Printer in Mac OS 9.x or Earlier
You’re ready to print! See the details in your Printer Basics book.
1
Open the Chooser.
2
Click the
3
Close the Chooser.
C84 Series icon, click your USB port, and turn on background printing.
You’re ready to start printing! See the details in your Printer Basics book.
When you see this screen, click the
Search for option, then click Next.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is a trademark of Epson America, Inc.
continue
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims
any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. 8/03
Printed in XXXXXX XX.XX-XX
5 Load Paper
1
2
Fan a few sheets of paper and
place them against the right
edge guide. Make sure the
paper is under the tabs on the
edge guides. Don’t push the
paper in.
5
You see a screen asking where you want Windows to search. Click CD-ROM drive.
Then click Next.
6
Click Next on the following screen.
7
When installation halts, click Finish.
8
Your computer detects your printer connection a
second time. Do one of the following:
Me
Press in the side of the left
edge guide and slide it against
the paper, but not too tightly.
Don’t load paper
above this arrow
98
6 Install Software
Follow the appropriate section below to install the printer software on Windows XP,
Windows Me, Windows 98, Windows 2000, or Macintosh.
For instructions on installing the software on Windows NT 4.x, see your Printer Basics book.
NOTE: To print from Macintosh Classic applications as well as OS X applications,
follow the steps below in OS X, then restart your Macintosh in OS 9 and follow the
steps below again.
Click Next on the next screen. The Add Printer Wizard screen appears.
Click Finish.
Click Next on each of the four screens that follow. The Add Printer Wizard appears.
Click Finish.
9
At the final Add New Hardare Wizard screen,
click Finish.
10
You see the license agreement. Read the agreement and click Agree.
NOTE: If the license agreement doesn’t appear, double-click the
CD-ROM icon, then double-click
EPSON.
Make sure your printer is on, then turn on your Macintosh. When you see your Macintosh
icons on the desktop, insert the CD-ROM in the CD-ROM or DVD drive.
2
If the CD-ROM window doesn’t open automatically, double-click the
EPSON CD-ROM icon.
3
Double-click
4
Read the License Agreement and click Agree.
5
At the Main Menu, click Install Printer Driver.
In Mac OS X, enter your administrator password
and click OK.
6
Follow the instructions on the screen and then restart
your computer.
7
Double-click the
CD Icon or
EPSON
CD-ROM icon again (if necessary), then double-click the
You see the Options Menu. Continue with the instructions below under “Finishing Windows
Installation” to complete your software installation.
Windows 2000
1
Turn on your computer. (Make sure your printer is still on.)
1
Turn on your computer. (Make sure your printer is still on.)
Wait for this screen to appear.
2
Wait until you see the Found New Hardware Wizard screen. Then put the EPSON
CD-ROM in your drive.
3
After a moment, click Next. You see a screen indicating
that Windows has found an unknown device.
4
Click the Search for option, then click Next.
NOTE: If you don’t see the Found New
Hardware screen, make sure your printer
is on and your cable is securely connected
to your printer’s port.
1
CD Icon or
EPSON.
EPSON
Windows XP
2
Macintosh
EPSON installer icon.
8
Optionally, click Install EPSON Software Film Factory and then click Install. Follow the
instructions on the screen.
9
Click Install Manual and Printer Movies to install the EPSON Printer Information Center.
NOTE: You need a browser – such as Microsoft Internet Explorer 4.0 or later or
Netscape Navigator® 4.0 or later – to view the guide.
10
When you’re done, click Exit to close the installer. You see the EPSON Product
Registration screen.
11
Register your printer as instructed. At the last screen, click Done or close your browser.
Then remove the CD-ROM.
3
Put the EPSON CD-ROM in your drive.
5
Make sure CD-ROM drives is selected, then click Next.
4
Wait while the files are copied to your computer.
6
At the next screen, click Next. Wait while the files are copied to your computer.
5
Click Finish when you see the final Found New Hardware Wizard screen.
7
Click Finish when you see the final Found New Hardware Wizard screen.
Add Your Printer in Mac OS X
6
You see the license agreement. Read the agreement and click Agree.
8
You see the license agreement. Read the agreement and click Agree.
1
Open the Applications folder on your hard drive, then open the Utilities folder and
double-click Print Center.
2
Choose Stylus C84 in the printer list and click the
You see the Options Menu. Continue with the “Finishing Windows Installation” instructions
to the right to complete your software installation.
You see the Options menu. Continue with the “Finishing Windows Installation” instructions to
complete your software installation.
Windows Me and 98
Finishing Windows Installation
1
1
Turn on your computer. (Make sure your printer is still on.) Wait until you see the
Add New Hardware Wizard.
2
3
Windows Me
Put the EPSON CD-ROM in your drive.
3
After a moment, click Next on the Add New Hardware Wizard screen. (In Windows
Me, you may not need to click Next.)
4
Me
98
If you’re running Windows 98,
continue with step 4.
Optionally, click Install EPSON Software
Film Factory and follow the on-screen instructions.
Click Install Manual and Printer Movies and follow
the on-screen directions to install the EPSON Printer
Information Center on your desktop.
Windows 98
2
If you’re running Windows Me,
go to step 7.
When you see this screen, make sure you have
paper in the printer, then click Print a Test Page
to check that your printer is set up correctly.
If you are using Mac OS X, add all your printer’s page setup options as described under “Add Your
Printer in Mac OS X.” If you are using Mac OS 9 or earlier, select your printer in the Chooser as
described under “Choose Your Printer in Mac OS 9 or earlier.”
Add icon.
NOTE: If you don’t see your printer in the Printer List, make sure the printer is
turned on and connected. Also make sure EPSON USB is selected.
3
Click the Stylus C84 icon to select it, then
choose All from the Page Setup menu.
4
Click Add. You see the Printer List with the
Stylus C84 and Stylus C84 (Sheet Feeder Borderless) printer options.
5
Choose EPSON USB
Choose All
Close Print Center.
Click Add
4
When you’re finished, click Exit to close the Options Menu.
You’re ready to start printing! See the details in
your Printer Basics book.
5
When you see the EPSON Product Registration screen, register your
printer as instructed, then remove your CD-ROM.
Choose Your Printer in Mac OS 9.x or Earlier
You’re ready to print! See the details in your Printer Basics book.
1
Open the Chooser.
2
Click the
3
Close the Chooser.
C84 Series icon, click your USB port, and turn on background printing.
You’re ready to start printing! See the details in your Printer Basics book.
When you see this screen, click the
Search for option, then click Next.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is a trademark of Epson America, Inc.
continue
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims
any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. 8/03
Printed in XXXXXX XX.XX-XX
5 Load Paper
1
2
Fan a few sheets of paper and
place them against the right
edge guide. Make sure the
paper is under the tabs on the
edge guides. Don’t push the
paper in.
5
You see a screen asking where you want Windows to search. Click CD-ROM drive.
Then click Next.
6
Click Next on the following screen.
7
When installation halts, click Finish.
8
Your computer detects your printer connection a
second time. Do one of the following:
Me
Press in the side of the left
edge guide and slide it against
the paper, but not too tightly.
Don’t load paper
above this arrow
98
6 Install Software
Follow the appropriate section below to install the printer software on Windows XP,
Windows Me, Windows 98, Windows 2000, or Macintosh.
For instructions on installing the software on Windows NT 4.x, see your Printer Basics book.
NOTE: To print from Macintosh Classic applications as well as OS X applications,
follow the steps below in OS X, then restart your Macintosh in OS 9 and follow the
steps below again.
Click Next on the next screen. The Add Printer Wizard screen appears.
Click Finish.
Click Next on each of the four screens that follow. The Add Printer Wizard appears.
Click Finish.
9
At the final Add New Hardare Wizard screen,
click Finish.
10
You see the license agreement. Read the agreement and click Agree.
NOTE: If the license agreement doesn’t appear, double-click the
CD-ROM icon, then double-click
EPSON.
Make sure your printer is on, then turn on your Macintosh. When you see your Macintosh
icons on the desktop, insert the CD-ROM in the CD-ROM or DVD drive.
2
If the CD-ROM window doesn’t open automatically, double-click the
EPSON CD-ROM icon.
3
Double-click
4
Read the License Agreement and click Agree.
5
At the Main Menu, click Install Printer Driver.
In Mac OS X, enter your administrator password
and click OK.
6
Follow the instructions on the screen and then restart
your computer.
7
Double-click the
CD Icon or
EPSON
CD-ROM icon again (if necessary), then double-click the
You see the Options Menu. Continue with the instructions below under “Finishing Windows
Installation” to complete your software installation.
Windows 2000
1
Turn on your computer. (Make sure your printer is still on.)
1
Turn on your computer. (Make sure your printer is still on.)
Wait for this screen to appear.
2
Wait until you see the Found New Hardware Wizard screen. Then put the EPSON
CD-ROM in your drive.
3
After a moment, click Next. You see a screen indicating
that Windows has found an unknown device.
4
Click the Search for option, then click Next.
NOTE: If you don’t see the Found New
Hardware screen, make sure your printer
is on and your cable is securely connected
to your printer’s port.
1
CD Icon or
EPSON.
EPSON
Windows XP
2
Macintosh
EPSON installer icon.
8
Optionally, click Install EPSON Software Film Factory and then click Install. Follow the
instructions on the screen.
9
Click Install Manual and Printer Movies to install the EPSON Printer Information Center.
NOTE: You need a browser – such as Microsoft Internet Explorer 4.0 or later or
Netscape Navigator® 4.0 or later – to view the guide.
10
When you’re done, click Exit to close the installer. You see the EPSON Product
Registration screen.
11
Register your printer as instructed. At the last screen, click Done or close your browser.
Then remove the CD-ROM.
3
Put the EPSON CD-ROM in your drive.
5
Make sure CD-ROM drives is selected, then click Next.
4
Wait while the files are copied to your computer.
6
At the next screen, click Next. Wait while the files are copied to your computer.
5
Click Finish when you see the final Found New Hardware Wizard screen.
7
Click Finish when you see the final Found New Hardware Wizard screen.
Add Your Printer in Mac OS X
6
You see the license agreement. Read the agreement and click Agree.
8
You see the license agreement. Read the agreement and click Agree.
1
Open the Applications folder on your hard drive, then open the Utilities folder and
double-click Print Center.
2
Choose Stylus C84 in the printer list and click the
You see the Options Menu. Continue with the “Finishing Windows Installation” instructions
to the right to complete your software installation.
You see the Options menu. Continue with the “Finishing Windows Installation” instructions to
complete your software installation.
Windows Me and 98
Finishing Windows Installation
1
1
Turn on your computer. (Make sure your printer is still on.) Wait until you see the
Add New Hardware Wizard.
2
3
Windows Me
Put the EPSON CD-ROM in your drive.
3
After a moment, click Next on the Add New Hardware Wizard screen. (In Windows
Me, you may not need to click Next.)
4
Me
98
If you’re running Windows 98,
continue with step 4.
Optionally, click Install EPSON Software
Film Factory and follow the on-screen instructions.
Click Install Manual and Printer Movies and follow
the on-screen directions to install the EPSON Printer
Information Center on your desktop.
Windows 98
2
If you’re running Windows Me,
go to step 7.
When you see this screen, make sure you have
paper in the printer, then click Print a Test Page
to check that your printer is set up correctly.
If you are using Mac OS X, add all your printer’s page setup options as described under “Add Your
Printer in Mac OS X.” If you are using Mac OS 9 or earlier, select your printer in the Chooser as
described under “Choose Your Printer in Mac OS 9 or earlier.”
Add icon.
NOTE: If you don’t see your printer in the Printer List, make sure the printer is
turned on and connected. Also make sure EPSON USB is selected.
3
Click the Stylus C84 icon to select it, then
choose All from the Page Setup menu.
4
Click Add. You see the Printer List with the
Stylus C84 and Stylus C84 (Sheet Feeder Borderless) printer options.
5
Choose EPSON USB
Choose All
Close Print Center.
Click Add
4
When you’re finished, click Exit to close the Options Menu.
You’re ready to start printing! See the details in
your Printer Basics book.
5
When you see the EPSON Product Registration screen, register your
printer as instructed, then remove your CD-ROM.
Choose Your Printer in Mac OS 9.x or Earlier
You’re ready to print! See the details in your Printer Basics book.
1
Open the Chooser.
2
Click the
3
Close the Chooser.
C84 Series icon, click your USB port, and turn on background printing.
You’re ready to start printing! See the details in your Printer Basics book.
When you see this screen, click the
Search for option, then click Next.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is a trademark of Epson America, Inc.
continue
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims
any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. 8/03
Printed in XXXXXX XX.XX-XX
Download PDF