Makita | CORDLESS ANGLE DRILL DA390D | Instruction manual | Makita CORDLESS ANGLE DRILL DA390D Instruction manual

Cordless Angle Drill
10 mm (3/8”) MODEL DA390D
10 mm (3/8”) MODEL DA390DW
With Fast Charger
INSTRUCTION MANUAL
SPECIFICATI0 NS
Model DA390D
Capacities
N o load speed
Steel
Wood
Wood screw
(RPMI
1 0 mm
(318”)
1 2 mm
(15132”)
4.5 mm x 2 0 mm
(3116“ x 314”)
800
Battery Cartridge 9000
Voltage
9.6 V
I
I
Dimensions
(L x W x HI
weight
335 mm x 59 mm x 115 mm
(13-1/4” x 2-3/8” x 4-1/2”1
1.3 kg
12.9 Ibsl
Model DC9700 Fast Charger
Charging time
1 Hr.
I
I
Input
A . C . only 50 H z - 60 Hz
I
I
output
D.C. 7.2 V
* Manufacturer reserves the right t o change specifications w i t h o u t notice.
* Note: Specifications m a y differ from country t o country.
~
9.6 V
IMPORTANT
SAFETY INSTRUCTIONS
(For All Tools)
WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools in damp
or wet locations. Keep work area well lit. Don’t expose power tools to rain.
Don’t use tool in presence of flammable liquids or gases.
3. KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don’t let visitors contact tool or extension cord.
4. STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place - out of reach of children.
5 . DON’T FORCE TOOL. It will do the job better and safer at the rate for which
it was intended.
6. USE RIGHT TOOL. Don‘t force small tool or attachment t o do the job of a
heavy-duty tool. Don‘t use tool for purpose not intended.
7 . DRESS PROPERLY. Don’t wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering t o contain long hair.
8 . USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
9. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
10. SECURE WORK. Use clamps or a vise to hold work. It’s safer than using
your hand and it frees both hands t o operate tool.
11. DON’T OVERREACH. Keep proper footing and balance at all times.
12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
13. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.
2
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it on.
15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger
on switch. Be sure switch is OFF when plugging in.
16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate
tool when you are tired.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked t o determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don’t use
tool if switch does not turn it on and off.
19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20. REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user - as well as damage to
the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
IMPORTANT SAFETY INSTRUCTIONS
I.
SAVE THESE INSTRUCTIONS - This manual
Length of Cord (Feet)
25
50
AWG Size of Cord
18
18
100
18
9.Do not operate charger with damaged cord or plug
150
16
- replace them immediately.
IO. Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it t o a qualified serviceman.
11. Do not disassemble charger or battery cartridge; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
12.To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
4
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF)
or ABOVE 4OoC (104OF).
2. Do not attempt t o use a step-up transformer, an engine generator or DC power
receptacle.
3. Do not allow anything t o cover or clog the charger vents.
4. Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2)Avoid storing battery cartridge in a container with other metal objects such
as nails, coins, etc.
(3)Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
5. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF).
6. Do not incinerate the Battery Cartridge even if it is severely damaged or is
completely worn out. The battery cartridge can explode in a fire.
ADDITIONAL SAFETY RULES
1. Be aware that this tool is always in an operating condition, because it does
not have t o be plugged into an electrical outlet.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. When drilling into walls, floors or wherever "live" electrical wires may be
encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL!
Hold the tool only by the insulated grasping surfaces t o prevent electric shock
if you drill into a "live" wire.
6. Do not leave the tool running. Operate the tool only when hand-held.
7. Do not touch the drill bit or the workpiece immediately after operation: they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
5
Installing or removing battery cartridge
0Always switch off the tool before insertion or removal of the battery cartridge.
0
0
To remove the battery cartridge, pull out
the set plate on the tool and grasp both
sides of the cartridge while withdrawing it
from the barrel.
To insert the battery cartridge, align the
Set plate
I
7
Battery cartridge
tongue on the battery cartridge with the
groove in the housing and slip it into
place. Snap the set plate back into place.
Be sure to close the set plate fully before
using the tool.
0
Do not use force when inserting the battery cartridge.
If the cartridge does not slide in easily, it i s not being inserted correctly.
Charging
Plug the fast charger into your power
source. Insert the battery cartridge so that
the plus and minus terminals on the battery cartridge are on the same sides as their
respective markings on the fast charger.
Insert the cartridge fully into the port so
that it rests on the charger port floor.
Press the start button (red). The charging
light will come on and charging will begin.
If the charging light does not come on,
press the reset button (yellow) first, then
the start button (red). If the charging light
goes out within 10 seconds even after pressing the reset button and start button a couple
of times, the battery cartridge i s dead. (CAUTION: Wait for more than 5 seconds after
the charging light goes out to press the reset button again.) Replace it with a new one.
When the charging light goes out after about one hour, you may remove the fully charged
battery cartridge.
After charging, unplug the charger from the power source.
CAUTION :
0Your new battery cartridge is not charged. You will need t o charge it before use.
.Do not keep the button pressed in with tape, etc. or the circuit will not function properly. Also, a malfunction of the charger may result possibly causing overheating, etc.
0 If you try t o charge a cartridge from a just-operated tool, sometimes the charging light
will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert i t
and try to charge it once more.
6
0
When you charge a new battery cartridge or a battery cartridge which has not been used
for a long period, it may not accept a full charge. This is a normal condition and does
not indicate a problem. You can recharge the battery cartridge fully after discharging
it almost completely a couple of times.
If you wish t o charge two battery cartridges, allow 15 minutes between chargings on the
fast charger.
Installing or removing driver bit or drill bit
CAUTION :
Always be sure that the tool i s switched off and the battery cartridge i s removed before
installing or removing the bit.
Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place
the bit in the chuck as far as it will go.
Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck.
To remove the bit, hold the ring and turn
the sleeve counterclockwise.
Switch action
Move the reversing switch lever to the
"FWD" position for clockwise rotation or
the "REV" position for counterclockwise.
To start the tool, simply pull the trigger.
Release the trigger to stop. When the reversing switch lever is in the neutral position, the tool will not start even if you pull
the trigger.
CAUTION :
Before inserting the battery cartridge into the tool, always check to see that the trigger
switch actuates properly and returns t o the "OFF" Position when released.
0
0
Always check the direction of rotation before drilling.
Use the reversing switch lever only when the tool comes to a complete stop. Changing
the direction of rotation before the tool stops may ruin the tool.
When not operating the tool, keep the reversing switch lever in the neutral position.
7
Drilling operation
0
0
Drilling in wood
When drilling in wood, best results are obrained with wood drills equipped with a guide
screw. The guide screw makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the b i t from slipping when starting a hole, make an indentation with a centerpunch and hammer a t the point t o be drilled. Place the point of the bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The exceptions are iron and brass which
should be drilled dry.
CAUTION :
Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and
shorten the service life of the tool.
0 There i s a tremendous force exerted on the tool/bit a t the time of hole breakthrough.
Hold the tool firmly and exert care when the b i t begins to breakthrough the workpiece.
0
A stuck b i t can be removed simply by setting the reversing switch t o reverse rotation in
order to back out. However, the tool may back out abruptly if you do not hold it firmly.
0Always secure small workpieces in a vise or similar hold-down device.
0
Screwdriving operation
Place the point of the driver bit in the
screw head and apply pressure t o the tool.
Start the tool. Release the trigger just as
the screw bottoms out. If the trigger is not
released, the screw may strip out the hole
or the screw and/or bit may be damaged.
NOTE :
0
Make sure that the driver bit i s inserted straight in the screw head, or the screw and/or
b i t may be damaged.
When driving wood screws. predrill Pilot
holes to make driving easier and t o prevent splitting of the workpiece. See the
chart.
8
Nominal diameter of
wood screw ( m m )
Recommended Size
of pilot hole (mm)
3.1 (1/8")
2.0
(5/64"
3.5 ( 9 / 6 4 ' )
2.2
(3/32"
3.8 (5/32")
2.5
(3132''
- 2.2
- 3/32")
- 2.5
- 3/32")
- 2.8
- 7/64")
Overload protect0r
The overload protector automatically cuts
out to break the circuit and the button
.pops out, whenever heavy work i s prolonged. Wait 20-30 seconds before pressing the restart button t o resume operation.
Your finger should not be on the trigger
when you press the restart button, however.
1
Restart button
MAINTENANCE
CAUTION :
Always be sure that the tool i s switched off and the battery cartridge i s removed before
attempting to perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment
should be performed by Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
9
ACCESSORIES
CAUTION :
These accessories o r attachments are recommended for use w i t h your Makita t o o l specified in this
manual. The use of any other accessories or attachments might present a risk of injury t o persons. The
accessories o r attachments should be used o n l y in the proper and intended manner.
0
Bits
Slotted
#5F
784010-0A
#7F
78401 1- 0 A
Square d r i l l b i t
0
Fast charger
Model D C 9 7 0 0
0
12 V Fast charger
Model D C 9 0 1 2
784606-0A
0
Rubber pad assembly
Part No. 123001-2
0
Battery cartridge 9000
Part No. 632007-4
0
Wool bonnet
Part No. 7 4 3 4 0 1 - 6
0
Foam polishing pad
Part No. 743023-2
0
Battery holster
Holster holds extra battery
Part No. 823033-3C
0
Steel carrying case
Part No. 182217-8
10
June-16'89
EN
10 mm (3/8")
CORDLESS ANGLE DRILL
Model DA390D
Note: The switch and other part configurations
may differ from country to country.
11
June-16-‘89
ITEM
NO.
NO.
USED
1
2
3
4
5
6
7
8
9
10
11
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
Plane Bearing 5
Retaining Ring S - 8
Spiral Bevel Gear 36
Ring 8
Ball Bearing 608LLB
Spindle
Keyless Chuck
Pan Head Screw M 5 x 2 2
Woodruff Key 3
Over Current Relay
Housing Set [With Item 191
r‘DM
$to
12
13
14
15
16
17
18
19
20
21
1
1
1
1
1
1
1
1
1
7
EN
DESCRIPTION
Name Plate
Switch
DC Motor 9 6 V
Gear
Plane Bearing 4
Battery 9 0 0 0
set Plate
Housing Set [With Item 111
Indication Label
Pan Head Screw M 4 x 2 2 [With Washer1
Note: The Switch and other part SPeCIfICattons may differ from country to country.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
tvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one- year period, return the COMPLETE
tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
e repairs have been made or attempted by others:
repairs are required because of normal wear and tear:
e The tool has been abused, misused or improperly maintained;
e alterations have been made t o the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDLNTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE O F THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM O F THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES O F “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-Y EAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states d o not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Some states d o not allow
limitation on how long an implied warranty lasts, so the above limitatlon may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446 Japan
8837088061
PRINTED IN JAPAN
1991 - 4 - N
Download PDF