Cisco Multiband Diversity Omnidirectional Ceiling-Mount Antenna AIR-ANTM4050V-R Installation guide

Cisco 860 Series, Cisco 880 Series, and
Cisco 890 Series Integrated Services
Routers Hardware Installation Guide
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number:
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCDE, CCENT, CCSI, Cisco Eos, Cisco Explorer, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase,
Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco TrustSec, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip
Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work,
Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and
Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the
IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY,
PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are
registered trademarks of Cisco and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (1002R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
© 2010 Cisco Systems, Inc. All rights reserved.
Preface
This preface describes the objectives, audience, organization, and conventions of this guide, and
describes related documents that have additional information. It contains the following sections:
•
Objective, page iii
•
Audience, page iii
•
Organization, page iv
•
Conventions, page iv
•
Related Documentation, page xii
•
Obtaining Documentation and Submitting a Service Request, page xii
Objective
This guide provides an overview and explains how to install, connect, and perform initial configuration
for the wireless and nonwireless Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated
Services Routers (ISRs). Some information may not apply to your particular router model.
For warranty, service, and support information, see the “Cisco One-Year Limited Hardware Warranty
Terms” section in Readme First for the Cisco 800 Series Integrated Services Routers that was shipped
with your router.
Audience
This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar
with Cisco routers and Cisco IOS software and features.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
iii
Preface
Organization
This guide is organized into the following chapters and appendix.
Chapter 1, “Product Overview”
Briefly describes the router models and the hardware
features available.
Chapter 2, “Installing the Router”
Lists the items shipped with the router, the
equipment and tools necessary for installing the
router, the safety warnings and guidelines, and the
procedures for installing the router.
Chapter 3, “Connecting the Router”
Describes typical connections for the router,
procedures for connecting the router to various
devices, and how to verify the connections.
Chapter 4, “Initial Configuration”
Provides the procedures for initially configuring the
router settings.
Appendix A, “Technical Specifications”
Provides the router, port, and cabling specifications.
Conventions
This section describes the conventions used in this guide.
Note
Caution
Tip
Means reader take note. Notes contain helpful suggestions or references to additional information and
material.
This symbol means reader be careful. In this situation, you might do something that could result in
equipment damage or loss of data.
Means the following information will help you solve a problem. The tip information might not be
troubleshooting or even an action, but could be useful information.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
iv
OL-16193-03
Preface
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
v
Preface
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
vi
OL-16193-03
Preface
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
vii
Preface
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
viii
OL-16193-03
Preface
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
ix
Preface
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical
Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown
on the code) for any other electrical devices than products designated by CISCO. The use of cables
that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the
code) is not limited to CISCO-designated products. Statement 371.
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions. Statement 1015
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool. Statement 1035
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations. Statement 1036
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface. Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning. Statement 1038
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
x
OL-16193-03
Preface
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS. Statement 1071
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2)
while the housing is open, or both. Statement 1043
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
xi
Preface
Related Documentation
In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation
Guide (this document), the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR documentation
set includes the following documents:
•
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
•
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software
Configuration Guide
•
Software Activation for Cisco Integrated Services Routers
•
Cisco IOS Software Activation Configuration Guide
•
Declarations of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g
and 802.11b/g Radios
•
Cisco IOS Release Notes
•
Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T
•
Cisco IOS Security Configuration Guide, Release 12.4T
•
Cisco IOS Security Command Reference, Release 12.4T
•
Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges, versions 12.4(10b) JA
and 12.3(8) JEC
•
Wireless LAN Controllers
•
Unified Wireless LAN Access Points
•
Cisco IOS Voice Port Configuration Guide
•
SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways
•
Cisco CP Express User’s Guide
Searching Cisco Documents
To search a Hyper Text Markup Language document using a web browser, press Ctrl-F (Windows) or
Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or
search forward and backward is also available.
To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader
Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document.
Use the Full Reader Search window to search multiple PDF files simultaneously and to change case
sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF
documents.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
xii
OL-16193-03
Preface
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
xiii
Preface
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
xiv
OL-16193-03
CH A P T E R
1
Product Overview
This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series,
and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:
•
General Description, page 1-1
•
Cisco 860 Series ISRs, page 1-2
•
Cisco 880 Series ISRs, page 1-3
•
Cisco 890 Series ISRs, page 1-11
•
Hardware Features, page 1-13
Note
For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and
SOHO Series Routers.
Note
The illustrations in this document show a wireless router. Both wireless and nonwireless models are
available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations
are similar for both wireless and nonwireless routers.
General Description
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi
CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup
capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These
routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers
provide advanced features such as global industry standard symmetrical high-speed DSL (G.SHDSL),
very-high-data-rate digital subscriber line 2–over–plain old telephone service (VDSL2oPOTS), 802.11n,
quality of service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL).
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with
built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These
ISRs are powered by an external power supply adapter. The various models differ in the WAN interface
and features that they support.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-1
Chapter 1
Product Overview
Cisco 860 Series ISRs
Cisco 860 Series ISRs
The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:
•
An integrated 4-port 10/100 Ethernet switch for connecting to the LAN
•
A10/100 Fast Ethernet (FE) or ADSL2 over POTs port for connecting to the WAN
•
Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
Figure 1-1 shows the front panel details of the Cisco 860 wireless router.
Front Panel of the Cisco 860 Series Wireless ISR
231969
Figure 1-1
1
1
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-2
OL-16193-03
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do
not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series
routers.
Figure 1-2
Back Panel of the Cisco 861W ISR
Cisco 861W
232181
WAN
FE 4
1
2
3
4
5
1
Primary WAN port1—10/100 FE or
ADSLoPOTSFE
5
Reset button
2
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
6
Power connector
3
4-port 10/100 Ethernet switch
7
Earth ground connection
4
Serial port—console or auxiliary
8
Kensington security slot
6
7
8
1. Depending on the router model, the primary WAN port can be 10/100 FE or ADSLoPOTs. The ADSLoPOTS WAN port is
in the same location as the 10/100 FE WAN port.
Cisco 880 Series ISRs
The Cisco 880 series ISRs have data and voice capabilities. They have the following features:
•
Integrated 4-port 10/100 Ethernet switch for connecting to the LAN
•
10/100 FE, VDSL2oPOTS, ADSL2+ over POTS, ADSL2+ over ISDN, or G.SHDSL port for
connecting to the WAN
•
Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
•
Optional 2-port Power over Ethernet (PoE)
•
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory
The following features are located on the front panel:
•
USB 1.1 port
•
Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the
Cisco 88xG models
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-3
Chapter 1
Product Overview
Cisco 880 Series ISRs
This section contains the following topics:
•
Cisco 880 Series Data Routers, page 1-4
•
Cisco 880 Series Voice Routers, page 1-7
Cisco 880 Series Data Routers
The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,
802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-3 and Figure 1-4 show the
features available on Cisco 880 series data routers. Some of the features shown may not be available on
your router.
Depending on the router model, the primary WAN port can be G.SHDSL, VDSL2oPOTS, or 10/100 FE.
See the Cisco 880 Series Integrated Services Routers data sheet for the WAN interface that is supported
on your router.
Figure 1-3 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G
card slot are located on the front panel.
Front Panel of the Cisco 880 Series Wireless Data Router
231950
Figure 1-3
1
1
2
2
3
LEDs
3G express card slot—Supports third-party
3G card (Cisco 88xG models only)
3
USB port
1
1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-4
OL-16193-03
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-4 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have
antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data
routers.
Back Panel of the Cisco 888W Data Router
231951
Figure 1-4
1
2
3
4
5
6
7
8
1
ISDN port—not available on 3G models
6
PoE power connector—optional
2
Primary WAN port1—G.SHDSL,
VDSL2oPOTS, ADSL2+oPOTS,
ADSL2+oISDN, or 10/100 FE
7
Reset button
3
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
8
Power connector
4
4-port 10/100 Ethernet switch
9
Earth ground connection
5
Serial port—console or auxiliary
10 Kensington security slot
9
10
1. Depending on the router model, the primary WAN port can be G.SHDSL, VDSL2oPOTS, or 10/100 FE. The VDSL2oPOTS
port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2
for location of the 10/100 FE WAN port.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-5
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-5
Back Panel of the Cisco 888E and Cisco 888E-W Data Router
B
RX/TX
C
RX
253233
A
RX/TX
1
2
3
4
6
5
6
7
1
ISDN port—not available on 3G models
2
Primary WAN port1—RJ-45 only, G.SHDSL, 7
VDSL2oPOTS, ADSL2+oPOTS,
ADSL2+oISDN, or 10/100 FE
3
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
8
Power connector
4
4-port 10/100 Ethernet switch
9
Earth ground connection
5
Serial port—console or auxiliary
10 Kensington security slot
8
9
10
PoE power connector—optional
Reset button
1. Depending on the router model, the primary WAN port can be G.SHDSL, VDSL2oPOTS, or 10/100 FE. The VDSL2oPOTS
port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2
for location of the 10/100 FE WAN port.
Caution
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non RJ-45 connector is inserted.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-6
OL-16193-03
Chapter 1
Product Overview
Cisco 880 Series ISRs
Back Panel of the Cisco 888EG Data Router
253231
Figure 1-6
1
2
3
4
6
5
6
7
1
3G Diag port
2
Primary WAN port1—RJ-45 only, G.SHDSL, 7
VDSL2oPOTS, ADSL2+oPOTS,
ADSL2+oISDN, or 10/100 FE
3
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
8
Power connector
4
4-port 10/100 Ethernet switch
9
Earth ground connection
5
Serial port—console or auxiliary
10 Kensington security slot
8
9
10
PoE power connector—optional
Reset button
1. Depending on the router model, the primary WAN port can be G.SHDSL, VDSL2oPOTS, or 10/100 FE. The VDSL2oPOTS
port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2
for location of the 10/100 FE WAN port.
Caution
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non RJ-45 connector is inserted.
Cisco 880 Series Voice Routers
The Cisco 880 series voice routers provide managed voice services that interface with Foreign Exchange
Station (FXS), Foreign Exchange Office (FXO), or Basic Rate Interface (BRI) connections. Figure 1-7,
Figure 1-8, and Figure 1-9 show the features available on the Cisco 880 series voice routers. The features
available vary, depending on the router model. Some features may not be available on your router.
Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the
Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are
supported on your router.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-7
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-7 shows the front panel details of the Cisco 880 series wireless voice router.
Front Panel of the Cisco 880 Series Wireless Voice Router
270495
Figure 1-7
1
1
LEDs
2
2
USB port
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-8
OL-16193-03
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-8 shows the back panel details of the Cisco 881SRST-W voice router.
Back Panel of the Cisco C881SRST-W Voice Router
241904
Figure 1-8
6
1
2
2
3
4
5
7
8
9
10
1
Primary WAN port1—10/100 FE
6
Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
2
Voice ports—four FXS2/DID3 ports, one
FXO4 port with TBP5 power failover
7
Reset button
3
4-port 10/100 Ethernet switch
8
Power connector
4
Serial port—console or auxiliary
9
Earth ground connection
5
PoE power connector—optional
10 Kensington security slot
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
2. FXS = Foreign Exchange Station.
3. DID = Direct Inward Dialing.
4. FXO = Foreign Exchange Office.
5. TBP = trunk bypass.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-9
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-9 shows the back panel details of the Cisco 888SRST-W voice router.
Back Panel of the Cisco C888SRST-W, Cisco IAD888EF, Cisco C888ESRST, and Cisco
C888ESRST-W Voice RouterRouters
241905
Figure 1-9
2
1
2
6
3
4
5
7
8
9
10
1
Primary WAN port1—G.SHDSL, RJ-45 only
on the C888ESRST-W. Voice BRI on the
IAD888EF
6
Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
2
Voice ports—four FXS2/DID3 ports and one
voice BRI 4port
7
Reset button
3
4-port 10/100 Ethernet switch
8
Power connector
4
Serial port—console or auxiliary
9
Earth ground connection
5
PoE power connector—optional
10 Kensington security slot
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
2. FXS = Foreign Exchange Station.
3. DID = Direct Inward Dialing.
4. BRI = Basic Rate Interface.
Caution
The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage
to the primary WAN port may occur if a non RJ-45 connector is inserted.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-10
OL-16193-03
Chapter 1
Product Overview
Cisco 890 Series ISRs
Back Panel of the Cisco IAD888EB Router
253230
Figure 1-10
1
2
3
4
5
6
7
8
9
10
1
Primary WAN port1—G.SHDSL
7
Serial port—console or auxiliary
2
Voice ports—four FXS/DID ports and one
voice BRI port.
8
PoE power connector—optional
3
Voice ports—four FXS/DID ports and one
voice BRI port.
9
Reset button
4
Primary WAN port—G.SHDSL, RJ-45 only
on the C888ESRST-W.
10 Power connector
5
Antenna—captive wireless omnidirectional
11
dipole WLAN antenna (wireless models only)
6
4-port 10/100 Ethernet switch
11 12
Earth ground connection
12 Kensington security slot
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
Cisco 890 Series ISRs
The Cisco 890 series ISRs have the following features:
•
Integrated 8-port 10/100 Ethernet switch for connecting to the LAN
•
10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN
•
Separate console and auxiliary ports
•
Optional embedded Wi-Fi CERTIFIED™ dual radio 802.11a/b/g/n-compliant wireless AP
•
Optional 4-port PoE
•
Security feature card (SFC) socket
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-11
Chapter 1
Product Overview
Cisco 890 Series ISRs
•
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory
•
Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for
non-captive dual-band WLAN antenna (wireless models only)
•
Supports the the AIM2-CUE-K9 and AIM2-APPRE-104-K9.
The following feature is located on the front panel:
•
Two USB 1.1 ports
Figure 1-11 shows the front panel details of the Cisco 890 wireless router.
Front Panel of the Cisco 890 Series Wireless ISR
272367
Figure 1-11
1
Rear Panel of the Cisco 890 Series Wireless ISR
241905
Figure 1-12
2
2
1
LEDs
1
2
6
3
2
4
5
7
8
9
10
USB ports
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-12
OL-16193-03
Chapter 1
Product Overview
Hardware Features
Figure 1-13 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have
RP-TNC antenna or connectors on the back panel. Some of the features that are shown may not be
available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Back Panel of the Cisco 892-W Router
272369
Figure 1-13
1
2
3
4
5
6
7
8
1
Antenna—dipole swivel antenna attached to
RP-TNC connectors (wireless models only)
7
PoE power connector
2
Backup—Data BRI1 or V.922 port
8
Reset button
3
Primary WAN port—FE and GE
9
Power connector
4
Auxiliary port
10 Earth ground connection
5
Console port
11 Kensington security slot
6
8-port 10/100 Ethernet switch
9
10 11
1. The Data BRI port is available only on the Cisco 892 router models.
2. The V.92 port (not shown) is available only on the Cisco 891 router models and is located between the console port and the
Ethernet switch.
Hardware Features
This section provides an overview of the following hardware features for the Cisco 860 series, 880
series, and 890 series ISRs. A feature summary is available at the end of this section.
•
Kensington Lock
•
Reset Button
•
LEDs
•
Memory
•
USB Port
•
Fan
•
Power over Ethernet Module
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-13
Chapter 1
Product Overview
Hardware Features
•
3G Cellular Data WAN Connectivity
•
Wireless LAN Connectivity
•
Feature Summary
Kensington Lock
A Kensington security slot is located on the router back panel. To secure the router to a desktop or other
surface, use the Kensington lockdown equipment.
Reset Button
The Reset button resets the router configuration to the default configuration set by the factory. To restore
the router configuration to the default configuration set by the factory, simultaneously press the reset
button while applying power to the router.
Note
When the CLI reboot command is issued while the embedded wireless AP is running Cisco Unified IOS
software, the router reboots and the AP continues running. Clients with Cisco Unified IOS software are
controlled by a wireless LAN controller (WLC) and can be reset only by the controller.
LEDs
The LEDs are located on the front panel of the router. Table 1-1 describes the LEDs for the Cisco 860
series, 880 series, and 890 series ISRs.
Table 1-1
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
LED
Color
Description
860 Series
880 Series
890 Series
Power OK
Green
On—DC power is being supplied to the router and the
Cisco IOS software is running.
All models All models All models
Blinking—Bootup is in process, or the router is in
ROMMON monitor mode.
Off—Power is not supplied to the router.
Link Status FE0
1
Green
Link Status FE1
On—Ethernet port is connected.
Link Status FE2
Blinking—Data is either being received or being
transmitted.
Link Status FE3
Off—Ethernet port is not connected.
Link Status FE4
Link Status FE5
Green
On—Ethernet port is connected.
Link Status FE6
Blinking—Data is either being received or being
transmitted.
Link Status FE7
Off—Ethernet port is not connected.
All models All models All models
—
—
All models
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-14
OL-16193-03
Chapter 1
Product Overview
Hardware Features
Table 1-1
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED
Color
Description
860 Series
880 Series
890 Series
FE WAN Port
Link Status
Green
On—Port is connected.
861
models
881
models
All models
—
—
All models
Wireless
models
Wireless
models
—
Wireless
models
Wireless
models
Wireless
models
Wireless
models
Wireless
models
—
Models
with PoE
Models
with PoE
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
GE WAN Port
Link Status
Green
On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
WLAN
(2.4 GHz)
Green
On—Radio is connected, SSID2 is configured, and client Wireless
models
is associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
WLAN (5 GHz)
Green
On—Radio is connected, SSID is configured, and client is —
associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
WLAN LINK
(Autonomous
Mode)
Green
On—Wireless link is up.
Blinking—Ethernet link is up, and data is either being
received or being transmitted.
Wireless
models
Off—Wireless link is down.
WLAN LINK
(Unified Mode)
Green
On—Ethernet link is up, and wireless access point (AP) is —
communicating with LWAPP3 controller.
Blinking—Ethernet link is up, but wireless AP is not
communicating with LWAPP controller.
Off—Ethernet link is down.
PoE4
Green
On—PoE is connected and powered.
Off—PoE is not installed.
VPN
PPP
5
6
Amber
On—Fault with the PoE.
Green
On—VPN is connected.
—
All models All models
Green
On—At least one PPP session is established.
—
All models All models
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-15
Chapter 1
Product Overview
Hardware Features
Table 1-1
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED
Color
7
xDSL CD
Green
Description
8
On—The xDSL interface is connected to the DSLAM .
Blink—Training to the line.
860 Series
880 Series
890 Series
867
models—
886, 887,
887V, 888
models
—
867 886
models
886, 887,
887V, 888
models
—
Off—Indicates that a connection has not been established
or the port is shut down.
xDSL Data
Green
Blink—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
9
Data BRI LINK Green
On—ISDN D channel is connected.
—886
models
886, 887,
887V, 888
models
892
models
Data BRI B1
Green
Blinking—B1 channel is either receiving or sending data, —886
or data is passing through ISDN channel 1.
models
886, 887,
887V, 888
models
892
models
Data BRI B2
Green
Blinking—B2 channel is receiving or sending data, or
data is passing through ISDN channel 2.
—886
models
886, 887,
887V, 888
models
892
models
3G10 WWAN11
Green
On—Service is established.
—
3G models —
—
3G models —
Slow Blinking—Searching for service.
Fast Blinking—Data is either being received or being
transmitted.
3G RSSI12
Green
Off—Low signal strength (lower than -100 dBm).
On—High RSSI (-69 dBm or higher).
Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
Fast Blinking—Medium RSSI (-89 to -70 dBm).
3G GSM
13
Amber
On—No service.
—
3G models —
Green
On—Service is established.
—
3G models —
—
3G models —
—
881
SRSTSRS
T16models
—
—
888 SRST
models
—
Off—No service.
3G CDMA
14
Green
On—Service is established.
Off—No service.
FXO
15
Voice
Green
On—FXO port is connected.
Blinking—FXO port is either receiving or transmitting
data.
BRI Voice LNK
Green
On—BRI interface is connected.
886, 887V,
888, SRST
models
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-16
OL-16193-03
Chapter 1
Product Overview
Hardware Features
Table 1-1
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED
Color
Description
860 Series
880 Series
890 Series
BRI Voice B1
Green
On—BRI B1 channel is connected.
—
888 SRST
models
—
Blinking—BRI B1 channel is either receiving or
transmitting data.
BRI Voice B2
Green
On—BRI B2 channel is connected.
886, 887V,
888, SRST
models
—
Blinking—BRI B2 channel is either receiving or
transmitting data.
FXS17/DID18
Voice
Green
V.92 Modem
Green
On—FXS/DID port is connected.
—
886, 887V,
888, SRST
models
—
886, 887V, —
888, SRST
models
—
—
Blinking—FXS/DID port is either receiving or
transmitting data.
On—Modem is connected.
888 SRST
models
Blinking—V.92 port is either receiving or transmitting
data.
891
models
1. FE = Fast Ethernet.
2. SSID = service set identifier.
3. LWAPP = Lightweight Access Point Protocol.
4. PoE = Power over Ethernet.
5. VPN = Virtual Private Network.
6. PPP = Point-to-Point Protocol.
7. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital
subscriber line), and G.SHDSL.
8. DSLAM = digital subscriber line access multiplexer.
9. BRI = Basic Rate Interface.
10. 3G = Third-Generation.
11. WWAN = wireless WAN.
12. RSSI = Received Signal Strength Indicator.
13. GSM = Global System for Mobile Communication.
14. CDMA = code division multiple access.
15. FXO = Foreign Exchange Office.
16. SRST = Survivable Remote Site Telephony.
17. FXS = Foreign Exchange Station.
18. DID = Direct Inward Dialing.
Memory
The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.
Flash Memory
The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The
onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON
boot code, and a separate non-volatile flash contains the cookie configuration.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-17
Chapter 1
Product Overview
Hardware Features
The default flash memory for the Cisco 860 series and 880 series routers is 128 MB. The default flash
memory for the Cisco 880 series voice routers and Cisco 890 series routers is 256 MB.
Note
Flash memory is not upgradable. An external USB flash memory module may be used if additional flash
memory is needed.
Main Memory
The Cisco 860 series routers contain 256 MB of onboard memory. The onboard memory in the Cisco 860
series router is not expandable.
The Cisco 880 series routers contain 256 MB of onboard memory and a single memory expansion slot
that accommodates a PC2-4200, 256-MB or 512-MB double data rate 2 (DDR2) SODIMM, for a
maximum of 768 MB.
The Cisco 890 series routers contain 512 MB of DRAM by default (256 MB of onboard memory and a
single memory expansion slot that accommodates a PC2-5300, 256-MB or 512-MB DDR2 SODIMM,
for a maximum of 768 MB).
USB Port
The Cisco 860 series and 880 series routers have a single Universal Serial Bus (USB 1.1-compliant) port
located on the front panel. The USB port provides connection for USB devices such as security tokens
and flash memory.
The Cisco 890 series routers have two USB 1.1-compliant ports located on the front panel.
Fan
Some router models do not have a fan, while other models have either one or two fans.
The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the
router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe
internal operating temperature.
Power over Ethernet Module
The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides
power to 802.3af-compliant devices connected to FE ports 0 and 1.
The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant
devices connected to FE ports 0, 1, 2, and 3.
The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a
48-V external power adapter.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-18
OL-16193-03
Chapter 1
Product Overview
Hardware Features
3G Cellular Data WAN Connectivity
The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS])
cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data
link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony
and broadband wireless data in a mobile environment.
The Cisco 88xG models come with a 34-mm express card slot ready for use with a commercial 3G card
radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the
Cisco 880 Series Integrated Services Routers data sheet.
Wireless LAN Connectivity
The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router
as an optional feature. The Cisco 860 series routers support autonomous features and network
configurations. The Cisco 880 series and 890 series routers support both autonomous and unified
features and network configurations.
The wireless AP does not have an external console port. Use the router’s console port as described in
Chapter 3, “Connecting a Terminal or PC to the Console Port.” To configure the wireless device, use the
Cisco IOS command-line interface (CLI).
Table 1-2 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.
The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz
frequency bands.
Table 1-2
Wireless Device Radios and Antennas
Maximum Data
Radio Band Throughput1
Radio Module
Platform
Single-band
802.11b/g/n draft 2.0
radio module
Cisco 860 and
880 series
routers
2.4 GHz
Dual-band
simultaneous
802.11a/n and
802.11b/g/n
radio module
Cisco 890
2.4 GHz
and 5 GHz
Up to 100 Mb/s
Mode
Antenna
Cisco 860 series:
autonomous only
Three captive 2-dBi
omnidirectional dipole
antennas
Cisco 880 series:
autonomous and
unified
100 Mb/s per radio, Autonomous and
up to 200 Mb/s
unified
total
Three dual-band,
removable,
2.4-GHz/5-GHz
omnidirectional dipole
RP-TNC antenna2
1. Actual data rate is highly dependent on your wireless environment.
2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the
following document on Cisco.com for feature information:
http://cisco.com/en/US/products/ps5853/prod_installation_guide09186a00804399cd.html
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-19
Chapter 1
Product Overview
Hardware Features
Supported Cisco Radio Antennas
The Cisco 890 series ISRs come with three removable dipole antennas that can be replaced using the
Cisco approved antenna extenders listed in Table 1-3.
Table 1-3
Cisco Antennas Supported on the Cisco 890 Series ISRs
Cisco Part Number
Antenna Type
Maximum Gain
Description
AIR-ANTM2050D-R
Omnidirectional
2.0 dBi at 2.4 GHz
This is the default antenna. It is a swivel-mount
dipole dual-band blade antenna. For more
information, see Cisco 2.4-GHz Swivel-Mount
Dipole Antenna (23.7786.51).
5.0 dBi at 5 GHz
AIR-ANTM4050V-R
Omnidirectional
4.0 dBi at 2.4 GHz
5.0 dBi at 5 GHz
AIR_ANTM5050P-R
Patch
5.5 dBi at 2.4 GHz
6.0 dBi at 5 GHz
Ceiling-mount dual-band antenna. This antenna
has a clip that allows it to be mounted on a
drop-ceiling cross member. For more information,
see Cisco Multiband Diversity Omnidirectional
Ceiling-Mount Antenna.
Wall-mount dual-band antenna. For more
information, see Cisco Multiband Wall-Mount,
Corner-Mount, or Mast-Mount Antenna.
Feature Summary
Table 1-4 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and
Cisco 890 series ISRs.
Table 1-4
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
Feature
Description
860 Series
880 Series
890 Series
Reset button
Resets the router configuration to the factory default.
All models
All models
All models
FE1 built-in
switch ports
Provides connection to 10/100BASE-T (10/100-Mbps)
All models
Fast Ethernet networks. The autosensing function in these
routers eliminates the need for a crossover cable and allows
the router to detect MDI2 or MDIX3 in any other PC or hub
with a straight-through cable or a crossover cable.
All models
All models
Console or AUX
port
Provides a connection to the terminal or PC for software
configuration or troubleshooting. The console port may be
configured as a virtual auxiliary port for dial backup and
remote management. The Cisco 890 series routers have
separate console and auxiliary ports.
All models
All models
All models
Security features Provides support for VPNs4, Cisco IOS Firewall, and
IPSec5. The Cisco 880 series routers also provide URL
filtering.
All models
All models
All models
Embedded
wireless AP
Wireless
models
Wireless
models
Wireless
models
802.11b/g/n
802.11b/g/n 802.11b/g/n
and 802.11a/n
The wireless AP is Wi-Fi CERTIFIED™
802.11a/b/g/n-compliant. The Cisco 860 series and
880 series routers contain a single 802.11b/g/n radio. The
Cisco 890 series routers contain dual 802.11b/g/n and
802.11a/n radios.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-20
OL-16193-03
Chapter 1
Product Overview
Hardware Features
Table 1-4
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature
Description
FE WAN port
860 Series
880 Series
890 Series
Provides connection to 10/100BASE-T. Can be connected to 861 models
other network devices, such as a cable modem, an xDSL6
modem, or router. The router is capable of bridging and
multiprotocol routing between the LAN and WAN ports.
881 models
All models
GE7 WAN port
10/100/1000 GE WAN Port.
—
—
All models
VDSL2oPOTS8
port
Provides connection to a VDSL2 network.
—
887V
—
ADSL2+oPOTS
Provides ADSL connection over basic telephone service
867
with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3 models—
(ADSL2), and G.992.5 (ADSL2+)
887
models887
V
—
ADSL2+oISDN
Provides ADSL connection over ISDN.
—
886
models886
—
Real-time clock
(RTC)
RTC provides nonvolatile date and time when the router is —
powered on. The RTC is used for verifying the validity of the
Certification Authority stored on the router. It is backed up
by a nonreplaceable lithium battery.
All models
All models
USB port
Supports high-speed USB 1.1. Provides connection for USB —
devices such as security tokens and flash memory.
All models
All models
The Cisco 880 series routers have a single USB port; the
Cisco 890 series routers have two USB ports.
PoE9
(Optional) Provides power for 802.3af-compliant devices
(such as phones) that are connected to the router.
—
Models with Models with
PoE
PoE
The Cisco 880 series routers support a 2-port PoE module;
the Cisco 890 series routers support a 4-port PoE module.
G.SHDSL10 port
Provides 2-wire or 4-wire connection to a G.SHDSL
network.
—
888 models
—
3G11 card slot
Provides backup data link.
—
3G models
—
Dying gasp
Detects when the router is about to lose power, and sends a —
power-fail signal to warn the DSLAM12 about the
impending line drop.
xDSL
models
—
Data BRI port
Provides backup and remote management functions by
connecting to the ISDN service provider if the main
VDSL213 or G.SHDSL link fails.
—
xDSL
models,
except for
the 3G and
SRST14
models
892 models
V.92 modem
Provides dial backup and remote management functions if
the main WAN link fails.
—
—
891 models
FXO15 port
An FXO interface connects local calls to a central office or
PBX. This is the interface a standard telephone provides.
—
881 SRST
models
—
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
1-21
Chapter 1
Product Overview
Hardware Features
Table 1-4
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature
16
FXS /DID
port
Description
17
BRI voice port
860 Series
880 Series
890 Series
An FXS interface connects directly to a standard telephone, —
fax machine, or similar device. This interface supplies
ringing voltage and dial tone to the station.
886, 887V,
888, SRST
models
—
The ISDN BRI S/T voice interface provides a client-side
—
(TE) ISDN S/T physical interface for connection to an NT1
device that terminates an ISDN telephone network.
888 SRST
models
—
886, 887V,
888, SRST
models
1. FE = Fast Ethernet.
2. MDI = media-dependent interface in normal mode.
3. MDIX = media-dependent interface in crossover mode.
4. VPN = Virtual Private Network.
5. IPsec = IP security.
6. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital
subscriber line), and G.SHDSL.
7. GE = Gigabit Ethernet
8. VDSL2oPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service.
9. PoE = Power over Ethernet.
10. G.SHDSL = (global industry standard) symmetrical high-speed DSL.
11. 3G = Third-Generation.
12. DSLAM = digital subscriber line access multiplexer.
13. VDSL2 = very-high-data-rate digital subscriber line 2.
14. SRST = Survivable Remote Site Telephony.
15. FXO = Foreign Exchange Office.
16. FXS = Foreign Exchange Station.
17. DID = Direct Inward Dialing.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-22
OL-16193-03
CH A P T E R
2
Installing the Router
This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series,
880 series, and 890 series Integrated Services Routers (ISRs), and contains the following sections:
•
Equipment, Tools, and Connections, page 2-1
•
Installing the Router, page 2-3
Note
For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that ships with the router and the Regulatory Compliance and Safety Information for Cisco 800
Series and SOHO Series Routers.
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Equipment, Tools, and Connections
This section describes the equipment, tools, and connections necessary for installing your Cisco 860
series, 880 series, and 890 series ISRs. It contains the following topics:
•
Items Shipped with your Router, page 2-2
•
Additional Items, page 2-2
•
Connections, page 2-2
•
Ethernet Devices, page 2-3
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-1
Chapter 2
Installing the Router
Equipment, Tools, and Connections
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the router.
Table 2-1 lists the items and their quantities that are shipped with each router model.
Table 2-1
Items and Their Quantities That Are Shipped with the Cisco 860 Series, Cisco 880
Series, and Cisco 890 Series ISRs
Cisco 860
Series Routers
Cisco 880
Series Routers
Cisco 890
Series Routers
1
1
1
1
1
1
RJ-45–to–DB-9 console cable
1
1
1
External 12 VDC power supply adapter
1
1
1
AC power supply cable
1
1
1
Cisco Configuration Professional (Cisco CP) 1
CD4
1
1
Item
Straight-through RJ-45 Ethernet cable1
2
RJ-11 DSL cable
3
1. Cisco 861 and Cisco 881 ISRs only.
2. DSL = digital subscriber line.
3. Cisco 888 ISRs only.
4. Cisco CP is optional by order and available only on some SKUs.
Additional Items
The following items are not shipped with the router but are required for installation:
•
ESD-preventive cord and wrist strap.
•
Screws for mounting the router on a wall:
– Two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10
washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate
at least 3/4 in. (20 mm) into the supporting wood or metal wall stud.
– Two number-10 wall anchors with washers, for mounting the router on a hollow-wall.
•
Wire crimper for chassis grounding.
•
Wire for connecting the chassis to an earth ground:
– AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding.
– AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding.
•
A ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding.
•
Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.
Connections
Obtain a broadband or Ethernet connection from your service provider.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-2
OL-16193-03
Chapter 2
Installing the Router
Installing the Router
Ethernet Devices
Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs.
Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
•
If you plan to configure the software using Cisco IOS commands through the console port, provide
an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
•
If you plan to connect a modem, provide the modem and modem cable.
•
If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.
•
If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.
Installing the Router
This section describes how to install the Cisco 860 series, 880 series, and 890 series ISRs. These routers
can either be installed on a table top or other flat horizontal surface or be mounted on a wall. The
Cisco 890 series ISRs may be mounted in a rack. This section also describes how to attach WLAN
antennas to the Cisco 890 series routers. This section contains the following topics:
•
Warnings, page 2-3
•
Installing Antennas, page 2-4
•
Installing on a Table, page 2-6
•
Mounting on a Wall, page 2-6
•
Installing in a Rack, page 2-9
•
Installing the Router Ground Connection, page 2-10
Warnings
Warning
This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect
the host to earth ground during normal use. Statement 242
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning
This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully
before beginning installation. Failure to use the correct hardware or to follow the correct procedures
could result in a hazardous situation to people and damage to the system. Statement 248
Caution
Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could
occur and cause damage to the router.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-3
Chapter 2
Installing the Router
Installing the Router
Caution
Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not
stack routers on a desktop. Excessive weight on top of the router could damage the chassis.
Caution
Do not install the router or power supplies next to a heat source of any kind, including heating vents.
Installing Antennas
The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC)
connectors on the back panel. The antennas that are shipped with the router are dual-band 2.4-GHz to
5-GHz omnidirectional dipole antennas.
Warning
Note
Statement 372—All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the
product only indoors.
Before you install the Cisco 890 series wireless router on a table, wall, or rack, connect the antennas to
the back panel. It is difficult to attach the antennas after the router is installed.
To attach the radio antennas to your wireless router, follow these steps:
Step 1
Manually screw the antennas tight to the RP-TNC connectors on the back of the router.
Attaching Antennas to the Router
272486
Figure 2-1
Step 2
Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with
respect to the floor.
a.
If the router is being mounted on a desk, orient the antennas straight up.
b.
If the router is being mounted on a wall, orient the antennas perpendicular to the floor as shown in
Figure 2-2 and Figure 2-3.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-4
OL-16193-03
Chapter 2
Installing the Router
Installing the Router
Antennas Oriented Vertically Up
274774
Figure 2-2
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-5
Chapter 2
Installing the Router
Installing the Router
Antennas Oriented Vertically Down
274775
Figure 2-3
Installing on a Table
To install the router on a table or other flat horizontal surface, firmly place the router on a table or other
horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space beside the cooling inlet and
exhaust vents.
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing the Router Ground Connection” section on page 2-10.
Mounting on a Wall
The Cisco 860 series, 880 series, and 890 series ISRs have mounting holes on the bottom of the chassis
for mounting the unit on a wall or other vertical surface.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-6
OL-16193-03
Chapter 2
Installing the Router
Installing the Router
Note
The mounting holes are bidirectional. You can hang the router with the front bezel facing upwards or
downwards.
Tip
When choosing a location for wall-mounting the router, consider cable limitations and wall structure.
To mount the router on a wall, follow these steps:
Step 1
Anchor the screws into the wall, leaving 1/8 inch (0.32 centimeter) between the screw head and the wall.
Figure 2-4 shows the wall-mount holes located on the underside of the router.
Figure 2-4
Wall-mount Holes on the Underside of the Router
8.200 in.
3.673 in.
1
1
231987
5.961 in.
1
Step 2
Wall-mount holes
Hang the router on the screws, and place the power adapter on a nearby horizontal surface. See
Figure 2-5.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-7
Chapter 2
Installing the Router
Installing the Router
Figure 2-5
Router Mounted on the Wall
1
1
4
231982
2
3
Step 3
1
Two number-10 wood screws mounted on the 3
wall
2
Wall-mount holes
4
Horizontal surface on which to place the
power adapter
Distance between the screw head and the wall,
1/8 in. (0.32 cm)
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing the Router Ground Connection” section on page 2-10.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-8
OL-16193-03
Chapter 2
Installing the Router
Installing the Router
Installing in a Rack
The Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow
these steps:
Step 1
Remove the screws shown in Figure 2-6.
Figure 2-6
Screw Location
278159
1
1
1
Step 2
Caution
Screws
Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis as shown
in Figure 2-7. Use two screws on each side. Use a number 2 Phillips screwdriver to install the bracket
screws on both sides of the chassis.
Do not overtorque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m).
Attaching the Rack-mount Brackets to the Cisco 890 Series ISR
272484
Figure 2-7
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-9
Chapter 2
Installing the Router
Installing the Router
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
-- This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
-- When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
-- If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the
rack. Statement 1006
Caution
Step 3
Chassis installation must allow unrestricted airflow for chassis cooling.
Using two screws for each side (supplied with the rack), attach the Cisco 890 series ISR with rack-mount
brackets to a 19-inch rack. Start with the lower pair of screws first, resting the brackets on the lower
screws while you insert the upper pair of screws.
Note
Be sure to leave space above and below each unit in a rack to allow for cooling air circulation.
Tip
The screw slots in the brackets are spaced to line up with every second pair of screw holes in the
rack. When the correct screw holes are used, the small threaded holes in the brackets line up with
unused screw holes in the rack. If the small holes do not line up with the rack holes, you must
raise or lower the brackets to the next rack hole.
Step 4
Place the power adapter on a nearby horizontal surface.
Step 5
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing the Router Ground Connection” section on page 2-10.
Installing the Router Ground Connection
The router must be connected to a reliable earth ground. Install the ground wire in accordance with local
electrical safety standards.
•
For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal
with an inner diameter of 1/4 in. (5 to 7 mm).
•
For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm2) or larger copper wire.
To install the ground connection, follow these steps:
Step 1
Strip one end of the ground wire to the length required for the ground lug or terminal.
Step 2
Crimp the ground wire to the ground lug or ring terminal, using the wire crimper.
Step 3
Attach the ground lug or ring terminal to the chassis as shown in Figure 2-8. For a ground lug, use the
two provided screws with captive locking washers. For a ring terminal, use one of the screws provided.
Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-10
OL-16193-03
Chapter 2
Installing the Router
Installing the Router
Chassis Ground Connection Using Ring Terminal
231981
Figure 2-8
1
1
Step 4
Ring terminal
Connect the other end of the ground wire to a known reliable earth ground point at your site.
After you install and properly ground the router, you can connect the power wiring, the WAN and LAN
cables, and the cables for administrative access as required for your installation.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
2-11
Chapter 2
Installing the Router
Installing the Router
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
2-12
OL-16193-03
CH A P T E R
3
Connecting the Router
This chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series
Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and the network. The
chapter contains the following sections:
•
Preparing to Connect the Router, page 3-2
•
Connecting a PC, Server, or Workstation, page 3-3
•
Connecting a Phone, page 3-4
•
Connecting an External Ethernet Switch, page 3-5
•
Connecting the V.92 modem Port, page 3-6
•
Connecting a Terminal or PC to the Console Port, page 3-7
•
Connecting a Modem to the Auxiliary Port, page 3-8
•
Connecting the 3G Card, page 3-9
•
Connecting a Data BRI Port, page 3-13
•
Connecting an FE Line to an FE WAN Port, page 3-15
•
Connecting an GE Line to an GE WAN Port, page 3-16
•
Connecting an xDSL Line, page 3-17
•
Connecting Power over Ethernet, page 3-18
•
Connecting the AC Adapter, page 3-18
•
Connecting an FXS Line, page 3-21
•
Connecting an FXO Line, page 3-23
•
Connecting a Voice ISDN BRI Line, page 3-24
•
Verifying Connections, page 3-26
Note
For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and
SOHO Series Routers.
Note
The illustrations in this chapter show a wireless router with antennas attached. Nonwireless routers do
not have antennas or antenna connectors on the back panel. However, the procedures for connecting
devices to the router are the same for both wireless and nonwireless routers.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-1
Chapter 3
Connecting the Router
Preparing to Connect the Router
Note
Depending on the features available for your router, some content in this chapter may not apply to your
router.
Preparing to Connect the Router
Before you connect the router to the devices, install the router according to the instructions in Chapter 2,
“Installing the Router.”
Preventing Damage to the Router
To prevent damage to your router, follow these guidelines when connecting devices to your router:
•
Caution
Turn off power to the devices and to the router until all connections are completed.
Do not turn on the devices until after you have completed all connections to the router.
•
Connect the color-coded cables supplied by Cisco Systems to the color-coded ports on the back
panel.
•
If you must supply your own cable, see Appendix A, “Technical Specifications,” for cabling
specifications. If this appendix does not provide specifications for a particular cable, we strongly
recommend ordering the cable from Cisco.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-2
OL-16193-03
Chapter 3
Connecting the Router
Connecting a PC, Server, or Workstation
Connecting a PC, Server, or Workstation
To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:
Step 1
Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows
a Cisco 888W router connected to a PC.
Figure 3-1
Connecting a Server, PC, or Workstation
2
1
231989
3
1
Yellow Ethernet cable supplied with the router 3
2
Ethernet switch port on the router
RJ-45 port on the network interface card1
1. Network interface card (NIC)
Step 2
Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed
in the PC, server, or workstation.
Step 3
(Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.
Note
Use the Cisco Configuration Express to configure the Internet connection settings. See
Cisco Configuration Professional Quick Start Guide for more information.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-3
Chapter 3
Connecting the Router
Connecting a Phone
Connecting a Phone
To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps:
Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2
shows a Cisco 888W router connected to a phone.
Figure 3-2
Connecting a Phone
270551
Step 1
2
1
3
1
4
GHI
7
Step 2
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
OPER
#
1
Yellow Ethernet cable
2
Ethernet switch port 1 on the router
3
RJ-45 port on a phone
Connect the other end of the cable to the RJ-45 port on the phone.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-4
OL-16193-03
Chapter 3
Connecting the Router
Connecting an External Ethernet Switch
Connecting an External Ethernet Switch
If more than four PCs in an office must be connected to each other, you can add Ethernet connections to
the router by connecting an external Ethernet switch to the router’s Ethernet switch.
To connect an external Ethernet switch to an Ethernet switch port on the router, perform the following
steps:
Step 1
Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-3 shows
a Cisco 888W router connected to an Ethernet switch.
Figure 3-3
Connecting to an Ethernet Switch
1
1
SYSTEM
1X
RPS
MODE
2
3
4
5
6
7
8
9
10
11
231986
3
12
STATUS
1
15X
UTIL
DUPLX
SPEED
1X
2X
2
3
4
5
6
7
8
9
10
11
12
15X
Catalyst 350
16X
2X
1
0 SERIES XL
INLINE POWE
R
16X
2
2
1
Ethernet switch port on the router.
2
Available port on the external Ethernet
switch.
3
Yellow CAT5 Ethernet cable,
RJ-45–to–RJ-45, connecting to an external
Ethernet switch port.
Step 2
Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet
connections.
Step 3
Turn on the Ethernet switch.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-5
Chapter 3
Connecting the Router
Connecting the V.92 modem Port
Connecting the V.92 modem Port
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
For dialup connection to your service provider network through the V.92 port, follow the steps given
after Figure 3-4, which show this connection.
Connecting to Your Service Provider Through the V.92 port
272387
Figure 3-4
1
2
1
V.92 port on the router
2
Telephone wall outlet
To connect the router to your service provide network through the V.92 port, follow these steps:
Step 1
Connect one end of the straight-through R-J11 cable to the V.92 port.
Step 2
Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-6
OL-16193-03
Chapter 3
Connecting the Router
Connecting a Terminal or PC to the Console Port
Connecting a Terminal or PC to the Console Port
Connect a terminal or PC to the Console Aux port either to configure the software by using the
command-line interface (CLI) or to troubleshoot problems with the router.
To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:
Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Figure 3-5 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router.
Figure 3-5
Connecting a Terminal or PC to the Console Port
231990
Step 1
1
2
1
Step 2
2
DB-9 connector
Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC.
Note
Step 3
RJ-45 connector to the Console Aux port on
the router
Some laptops and personal computers do not come with DB-9 serial port connectors and may
require a USB-to-serial port adapter.
To communicate with the router, start a terminal emulator application.
Terminal Emulator Settings
Use the following settings for the terminal emulator connection:
•
9600 baud
•
8 data bits, no parity
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-7
Chapter 3
Connecting the Router
Connecting a Modem to the Auxiliary Port
•
1 stop bit
•
No flow control
When the terminal emulator establishes communications, the router prompt is displayed.
For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings
for Console Connections.
Connecting a Modem to the Auxiliary Port
To connect a modem to the router, follow these steps:
Step 1
Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-6.
Connecting a Modem to the Aux Port
272386
Figure 3-6
1
2
3
4
1
Aux port (RJ-45)
3
DB-9 to DB-25 modem adapter (if required)
2
Light blue console cable
4
Modem
Step 2
Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.
Step 3
Connect the DB-25 end of the modem adapter to the modem.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-8
OL-16193-03
Chapter 3
Connecting the Router
Connecting the 3G Card
Step 4
Make sure that your modem and the router auxiliary port are configured for the same transmission speed
(up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect
(DCD) and data terminal ready (DTR).
Connecting the 3G Card
Note
The Cisco 880G router does not support OIR of the 3G card. You must enter the shutdown command on
the cellular interface before you remove the 3G card from the router.
To connect and secure the 3G card, follow these steps:
Step 1
Align the 3G card to the 3G express card slot, as shown in Figure 3-7. Keep the card parallel to the
surface and firmly push the card into the slot.
Tip
Holding the 3G card on the flat metal surface will make it easier to align and insert the 3G card.
Note
When inserting the card into the 3G express card slot, you may hear a metal-on-metal sound as
the 3G card rubs against the internal metal cage. The 3G card is designed to fit tightly into the
3G express card slot. Firm pressure may be required to insert the card.
Note
Global System for Mobile Communications (GSM) customers need to insert a SIMM card,
provided by their network carrier, into the 3G card.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-9
Chapter 3
Connecting the Router
Connecting the 3G Card
Figure 3-7
Inserting the 3G Card
4
271473
3
2
3
1
6
5
5
1
3G card with the Cisco logo facing up
4
Screw holes for locking bracket
2
3G express card slot
5
Pin holes for aligning the locking bracket
3
Notches on the 3G card
6
SIMM slot (in HSPA1 cards only)
1. HSPA = High-Speed Packet Access.
Open the top of the anti-theft locking bracket, as shown in Figure 3-8.
Figure 3-8
Opening the Anti-theft Locking Bracket
Front View
Back View
271474
Step 2
1
1
1
Pins on the locking bracket for alignment
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-10
OL-16193-03
Chapter 3
Connecting the Router
Connecting the 3G Card
Step 3
Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches
on either side of the 3G card, as shown in Figure 3-9, and the pins on the locking bracket should be
inserted into the corresponding holes in the router.
Figure 3-9
Installing the Locking Bracket
1
2
271726
3
1
3G card
2
Locking bracket
3
Notch on the 3G card
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-11
Chapter 3
Connecting the Router
Connecting the 3G Card
Step 4
Close the locking bracket, as shown in Figure 3-10.
Figure 3-10
Closing the Locking Bracket
1
271580
2
1
Step 5
2
3G card
Locking bracket
Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.
Figure 3-11
Inserting the Screws
271476
4
1
3
Step 6
4
2
1
3G card
3
Screws
2
Locking bracket
4
Screw holes on the locking bracket
To connect the antenna to the 3G card, insert the antenna connector into the antenna connector hole on
the 3G card. Figure 3-12 show the antenna connected to the 3G card.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-12
OL-16193-03
Chapter 3
Connecting the Router
Connecting a Data BRI Port
Figure 3-12
Antenna connected to the 3G Card
272653
1
3
2
1
Antenna on a cradle
2
Antenna connector
3
Antenna connector receptacle1
1. In HSPA cards, the antenna connector receptacle is located on the right side of the 3G card.
Step 7
Clean the flat surface to which you will affix the antenna.
Step 8
Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the
cradle to the flat surface.
Connecting a Data BRI Port
You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in
case the primary xDSL (general term referring to various forms of DSL, including global industry
standard symmetrical high-speed DSL [G.SHDSL]) WAN service fails. The Data BRI connection is not
available on the third-generation (3G) models.
The cabling requirements for the ISDN S/T connection are as follows:
Caution
•
You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the
splitter, and the second cable connects the splitter to the wall jack.
•
There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. However, an
RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an
RJ-11 connector. Contact your router reseller for the appropriate cable.
Both LAN and WAN ports use RJ-45 connectors. Use caution when connecting cables to these
connectors. To avoid damage to the router, do not connect telephone-network voltage (TNV) circuits
(such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits).
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-13
Chapter 3
Connecting the Router
Connecting a Data BRI Port
Although the following procedure shows a Cisco 888W data router, this procedure applies to all
Cisco 880 series router with a Data BRI port.
To connect the Data BRI port to the ISDN service provider, follow these steps:
Step 1
Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-13 shows a
Data BRI connection.
Figure 3-13
Connecting the Data BRI Port to the ISDN Line
3
1
7
231991
2
4
6
8
5
9
10
5
1
Data BRI port on the router
6
U-port on the NT1 box
2
ISDN S/T cable
7
xDSL splitter (provided by the xDSL service
provider)
3
Network termination 1 (NT1) box
8
Telephone line port on the splitter
4
S/T port on the NT1 box
9
Telecommunication service port on the
splitter
5
Unshielded CAT 5 cable
10 Wall jack
Step 2
Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box.
Step 3
Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on
the splitter.
Step 4
Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter
to the wall jack to allow a link to the network service provider.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-14
OL-16193-03
Chapter 3
Connecting the Router
Connecting an FE Line to an FE WAN Port
Connecting an FE Line to an FE WAN Port
To connect the Fast Ethernet (FE) WAN port on the router, follow these steps:
Step 1
Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-14.
Figure 3-14
Connecting the FE WAN Port
1
231992
WAN
FE 4
1
2
3
Internet
Step 2
1
FE WAN port
2
CAT 5 cable
3
Modem connected to the Internet
Connect the other end of cable to an available port on the modem.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-15
Chapter 3
Connecting the Router
Connecting an GE Line to an GE WAN Port
Connecting an GE Line to an GE WAN Port
To connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps:
Step 1
Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-14.
Connecting the GE WAN Port
274493
Figure 3-15
1
2
3
Internet
Step 2
1
GE WAN port
2
CAT 5 cable
3
Modem connected to the Internet
Connect the other end of cable to an available port on the modem.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-16
OL-16193-03
Chapter 3
Connecting the Router
Connecting an xDSL Line
Connecting an xDSL Line
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
To connect the router to a global industry standard symmetrical high-speed DSL (G.SHDSL) line,
very-high-speed digital subscriber line 2 (VDSL2) port, or an ADSL2+ line, follow these steps:
Step 1
Connect one end of an RJ-11 (RJ-45 on 880 E models) cable to the port on the router. See Figure 3-16.
Figure 3-16
Connecting the xDSL Line
2
232175
1
1
Step 2
Caution
Note
G.SHDSL port, VDSL2oPOTS port, or
ADSL2+ port
2
DSL wall jack
Connect the other end of the cable to the DSL wall jack.
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may
occur if a non RJ-45 connector is inserted
The DSL line must be provisioned by your service provider and correctly configured so that the LED
shows the carrier detect (CD) status.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-17
Chapter 3
Connecting the Router
Connecting Power over Ethernet
Connecting Power over Ethernet
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028
Figure 3-17 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router.
The PoE adapter provides power to ports 0 and 1 of the 4-port 10/100 FE switch on the Cisco 880 series
routers and ports 0,1, 2, and 3 of the 8-port 10/100 FE switch on the Cisco 890 series routers.
Note
The router must also be connected to an AC power outlet through a 12-VDC adapter. To connect the
router to an AC outlet, see “Connecting the AC Adapter” section on page 3-18.
Note
Be sure that the internal PoE is enabled for this connection procedure to work.
Figure 3-17
Connecting PoE
1
4
5
2
3
4
6
231995
2
1
48-VDC PoE input jack
4
AC plug
2
Power cord
5
12-VDC input power-jack plug
3
Power adapter—48 VDC
6
Power adapter—12 VDC
Connecting the AC Adapter
Warning
The device is designed to work with TN power systems. Statement 19
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-18
OL-16193-03
Chapter 3
Connecting the Router
Connecting the AC Adapter
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used on
the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have
adequate safety approvals recognized by the country of usage. Statement 119
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028
To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps:
Step 1
Connect the router to an AC power outlet as shown in Figure 3-18.
Figure 3-18
Connecting the AC Adapter
1
2
231996
4
3
1
12-VDC plug
3
Power adapter—12 VDC
2
Power cord
4
AC plug
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-19
Chapter 3
Connecting the Router
Connecting the AC Adapter
Step 2
To secure the power cord to the router, attach the power lock clip to the power cord, and slide the clip to
the end of the DC plug. See Figure 3-19.
Figure 3-19
Securing the Power Cord
3
2
4
270659
1
1
Power lock clip
3
DC plug
2
Power cord
4
Lock holes on either side of the power
connector
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-20
OL-16193-03
Chapter 3
Connecting the Router
Connecting an FXS Line
Step 3
Snap the latches into the holes on either side of the power connector. See Figure 3-20.
Figure 3-20
Power Lock Clip Latched Into the Holes on Either Side of the Power Connector
1
4
3
270800
2
1
Power lock clip
3
Power adapter
2
Power cord
4
AC plug
Connecting an FXS Line
Use a standard straight-through RJ-11 modular telephone cable to connect an Foreign Exchange Service
(FXS) port to a telephone or fax machine.
Warning
This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do
not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11
port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming
call.
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection: FXS.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-21
Chapter 3
Connecting the Router
Connecting an FXS Line
To connect the FXS line, follow these steps:
Step 1
Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-21 shows an FXS line
connection.
Figure 3-21
Connecting an FXS Line
1
2
241907
3
Fax machine
or telephone
Step 2
1
FXS port
2
RJ-11 cable
3
RJ-11 port
Connect the other end of the cable to the RJ-11 port on the fax or telephone machine.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-22
OL-16193-03
Chapter 3
Connecting the Router
Connecting an FXO Line
Connecting an FXO Line
Use a straight-through RJ-11 cable to connect the Foreign Exchange Office (FXO) voice port to the
PSTN or PBX through a telephone wall outlet.
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
To connect the FXO line, follow these steps:
Step 1
Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-22.
Figure 3-22
Connecting an FXO Line
2
1
270542
3
Step 2
1
FXO port
2
RJ-11 cable
3
Telephone outlet
Connect the other end of the RJ-11 cable to a telephone wall outlet.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-23
Chapter 3
Connecting the Router
Connecting a Voice ISDN BRI Line
Note
If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX)
connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure
that the soft-offhook option is enabled on the port.
This option allows a stepped offhook resistance during seizure which avoids overloading the circuit
during offhook in the event that ringing voltage is present on the circuit at the same time as the trunk
seizure. The stepped offhook resistance is initially set to 800 Ohms, then adjusts to 50 Ohms when
ringing voltage is not present.
To enable soft-offhook command on the port, and to access the connection command with plar opx
syntax, see the Cisco Command Lookup Tool.
Connecting a Voice ISDN BRI Line
Use a straight-through RJ-45 cable to connect the voice BRI port to the ISDN network through a
telephone outlet or other device.
Caution
To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only, and not to
any other RJ-45 connector.
To connect the voice BRI line, follow these steps:
Step 1
Connect one end of a straight-through RJ-45–to–RJ-45 cable to the Voice BRI port.
Note
When the interface is configured as NT and is connecting to a TE device, use a crossover cable.
See Table A-11.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-24
OL-16193-03
Chapter 3
Connecting the Router
Connecting a Voice ISDN BRI Line
Figure 3-23 shows a voice BRI line connection.
Figure 3-23
Connecting a Voice BRI Line
1
2
241906
3
Step 2
1
Voice BRI port
2
RJ-45 cable
3
Telephone outlet
Connect the other end of the cable to the RJ-45 telephone outlet or other device.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-25
Chapter 3
Connecting the Router
Verifying Connections
Verifying Connections
To verify that all devices are properly connected to the router, first turn on all the connected devices.
Then check the LEDs. To verify router operation, refer to Table 3-1.
For full LED description see Table 1-1 “LED Descriptions for the Cisco 860 Series, Cisco 880 Series,
and Cisco 890 Series ISRs”.
Table 3-1
Verifying the Router Operation
Power and Link
LEDs to Check
Normal Patterns
Power
OK
On when power is supplied to the router.
To servers, PCs,
LAN 0, LAN 1, LAN 2, or LAN 3
workstations, or an
external Ethernet switch
connected to the LAN
ports (FE01, FE1, FE2,
or FE3)
On when the FE LAN port is physically connected to a
server, PC, workstation, or external Ethernet switch.
To FE WAN line
On when the WAN Ethernet carrier has detected status.
WAN FE4
Blinks when receiving or transmitting data.
2
To xDSL line
To ISDN line
3G
4
xDSL CD
Green when the line is connected to the xDSL DSLAM3.
xDSL Data
Green when receiving or sending data.
Data BRI LNK
Green when the ISDN line is connected.
Data BRI B1 and B2
Green when the channel is connected.
WWAN
5
Green when service is established.
Slow blinking when searching for service.
RSSI
6
Amber when service is not established.
Green when signal strength is high.
Off or slow blinking when signal strength is low.
Fast blinking when signal strength is medium.
CDMA
GSM
9
8
7
Green when service is established.
Green when service is established.
To PPP clients
PPP
Green when either a PPPoE10 or PPPoA11 client is running.
To VPN12 tunnel
VPN
Green when a crypto session is running.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-26
OL-16193-03
Chapter 3
Connecting the Router
Verifying Connections
Table 3-1
Verifying the Router Operation (continued)
Power and Link
LEDs to Check
Normal Patterns
To wireless LAN
WLAN LINK
Wireless LAN link status:
WLAN 2.4 GHz
WLAN 5.0 GHz
PoE14
•
Green if at least one client is associated.
•
Off if no client is associated.
Wireless LAN 2.4-GHz status:
•
Green when radio is connected, SSID13 is configured,
signal is being transmitted, and client is associated.
•
Slow blinking when radio is connected, SSID is
configured, and signal is being transmitted.
Wireless LAN 5.0-GHz status:
•
Green when radio is connected, SSID is configured,
signal is being transmitted, and client is associated.
•
Slow blinking when radio is connected, SSID is
configured, and signal is being transmitted.
PoE 0
Green when connected and powered.
PoE 1
Amber when there is a fault with the inline power supply.
1. FE = Fast Ethernet.
2. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital
subscriber line), and G.SHDSL.
3. DSLAM = digital subscriber line access multiplexer.
4. 3G = Third-Generation.
5. WWAN = wireless WAN.
6. RSSI = Received Signal Strength Indicator.
7. CDMA = code division multiple access.
8. GSM = Global System for Mobile Communications.
9. PPP = Point-to-Point Protocol.
10. PPPoE = PPP over Ethernet.
11. PPPoA = PPP over ATM.
12. VPN = Virtual Private Network.
13. SSID = service set identifier.
14. PoE = Power over Ethernet.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
3-27
Chapter 3
Connecting the Router
Verifying Connections
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
3-28
OL-16193-03
CH A P T E R
4
Initial Configuration
This chapter provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890
series Integrated Services Routers (ISRs). For the initial configuration, we recommend using
Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user
interface that guides you through initial configuration.
You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by
using the setup command facility. To create the initial configuration, the setup command facility prompts
you for basic information about your router and network.
This chapter contains the following sections:
Note
•
Cisco Configuration Professional Express, page 4-1
•
Cisco IOS CLI, page 4-1
•
Setup Command Facility, page 4-3
•
Verifying the Initial Configuration, page 4-5
•
Initial Configuration of the Wireless Access Point, page 4-5
Some SKUs may not include a default configuration file. If your router does not have a default
configuration file, go to the “Setup Command Facility” section on page 3 to configure the initial router
settings.
Cisco Configuration Professional Express
After you connect the cables and power up the router, we recommend that you use the Cisco CP Express
web-based application to configure the initial router settings.
For instructions on how to use Cisco CP Express to configure the router see the Cisco CP Express User’s
Guide.
Cisco IOS CLI
To configure the initial router settings by using the Cisco IOS CLI, you will need to set up a console
connection. For instructions on how to set up a console connection, see the “Connecting a Terminal or
PC to the Console Port” section on page 3-7.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
4-1
Chapter 4
Initial Configuration
Cisco IOS CLI
To configure the initial router settings using the Cisco IOS CLI, follow these steps:
Step 1
Set up a console connection to your router. The following message is displayed:
...
router con0 is now available
Step 2
Press Return or Enter. The following message is displayed:
Cisco Configuration Professional Express (Cisco CP Express) is installed on this device.
This feature requires the one-time use of the username "username1"
with the password "password1." The default username and password have a privilege level of
15.
Please change these publicly known initial credentials using Cisco CP Express or the Cisco
IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username username1
Replace <myuser> and <mypassword> with the username and password you want to use.
For more information about Cisco CP please follow the instructions in the QUICK START
GUIDE for your router...
...
User Access Verification
Username:
Step 3
Enter the username username1, and press Return or Enter. The following prompt is displayed:
Password:
Step 4
Enter the password password1, and press Return or Enter. The following prompt is displayed:
Router#
A message is displayed that is similar to the first warning message. The message directs you to change
the username and password.
You are now in privileged EXEC mode.
Note
Step 5
You must change the username and password before you log off the router. You cannot use the
username username1 or password password1 after you log off from this session.
To change the username and password, enter the following at the prompt:
username username privilege 15 secret 0 password
The username and password are the username and password that you wish to use.
To continue using the Cisco IOS CLI for initial configuration, see the applicable configuration
procedures in the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers
Software Configuration Guide.
Note
Save your configuration changes regularly to avoid losing them during resets, power cycles, or
power outages. Use the copy running-config startup-config command at the privileged EXEC
mode prompt (Router#) to save the configuration to NVRAM.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
4-2
OL-16193-03
Chapter 4
Initial Configuration
Setup Command Facility
Step 6
Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.
Setup Command Facility
The setup command facility guides you through the configuration process by prompting you for the
specific information that is needed to configure your system. Use the setup command facility to
configure a hostname for the router, to set passwords, and to configure an interface for communication
with the management network.
To use the setup command facility, you will need to set up a console connection with the router and enter
the privileged EXEC mode.
Note
For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to
the Console Port” section on page 3-7.
To configure the initial router settings by using the setup command facility, follow these steps:
Step 1
Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to
enter privileged EXEC mode, see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1.
Step 2
In privileged EXEC mode, at the prompt, enter setup.
yourname# setup
The following message is displayed:
--- System Configuration Dialog --Continue with configuration dialog? [yes/no]:
You are now in the setup command facility.
The prompts in the setup command facility vary, depending on your router model, on the installed
interface modules, and on the software image. The following steps and the user entries (in bold) are
shown as examples only.
Note
Step 3
If you make a mistake while using the setup command facility, you can exit and run the setup
command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC
mode prompt (Router#). For more information on using the setup command facility, see “The
Setup Command” chapter in the Cisco IOS Configuration Fundamentals Command Reference,
Release 12.2T document.
To proceed using the setup command facility, enter yes:
Continue with configuration dialog? [yes/no]: yes
Step 4
When the following messages appear, enter yes to enter basic management setup:
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
4-3
Chapter 4
Initial Configuration
Setup Command Facility
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
Step 5
Enter a hostname for the router (this example uses Router):
Configuring global parameters:
Enter host name [Router]: Router
Step 6
Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when
viewing the configuration.
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: xxxxxx
Step 7
Enter an enable password that is different from the enable secret password. This password is not
encrypted (less secure) and can be seen when viewing the configuration.
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: xxxxxx
Step 8
Enter the virtual terminal password, which prevents unauthenticated access to the router through ports
other than the console port:
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: xxxxxx
Step 9
Respond to the following prompts as appropriate for your network:
Configure SNMP Network Management? [yes]:
Community string [public]:
A summary of the available interfaces is displayed.
Step 10
Choose one of the available interfaces for connecting the router to the management network:
Enter interface name used to connect to the
management network from the above interface summary: fastethernet4
Step 11
Respond to the following prompts as appropriate for your network:
Configuring interface FastEthernet0:
Use the 100 Base-TX (RJ-45) connector? [yes]: yes
Operate in full-duplex mode? [no]: yes
Configure IP on this interface? [yes]: yes
IP address for this interface: 172.1.2.3
Subnet mask for this interface [255.255.0.0] : 255.255.0.0
Class B network is 172.1.0.0, 26 subnet bits; mask is /16
The configuration is displayed:
The following configuration command script was created:
hostname Router
enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1
enable password xxxxxx
line vty 0 4
password xxxxxx
snmp-server community public
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
4-4
OL-16193-03
Chapter 4
Initial Configuration
Verifying the Initial Configuration
!
no ip routing
!
interface FastEthernet0
no shutdown
speed 100
duplex auto
ip address 172.1.2.3 255.255.0.0
!
Step 12
Respond to the following prompts. Enter 2 to save the initial configuration.
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started! RETURN
The user prompt is displayed.
Router>
Step 13
Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for
verification procedures.
After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional
configuration.
Verifying the Initial Configuration
To verify that the new interfaces are operating correctly, perform the following tests:
•
To verify that the interfaces and line protocol are in the correct state—up or down—enter the show
interfaces command.
•
To display a summary status of the interfaces configured for IP, enter the show ip interface brief
command.
•
To verify that you configured the correct hostname and password, enter the show configuration
command.
After you complete and verify the initial configuration, you can configure your Cisco router for specific
functions.
Initial Configuration of the Wireless Access Point
The embedded wireless access point (AP) runs its own IOS. You can initially configure the embedded
wireless AP by using one of the following methods:
•
Cisco Configuration Professional (CP) Express
•
Setup command facility on the embedded wireless device
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
4-5
Chapter 4
Initial Configuration
Initial Configuration of the Wireless Access Point
For information on how to do basic wireless configuration on your router see the “Basic Wireless
Device” chapter of the Cisco 860 Series, Cisco 880, and Cisco 890 Series Integrated Services Routers
Software Configuration Guide.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
4-6
OL-16193-03
A P P E N D I X
A
Technical Specifications
This appendix provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series,
and Cisco 890 series Integrated Services Routers (ISRs). It contains the following sections:
•
Router Specifications, page A-2
•
Wireless Access Point, page A-3
•
FE and GE Port Pinouts, page A-3
•
Console and Auxiliary Port Connector Pinouts, page A-4
•
FXS and FXO Port Connector Pinouts, page A-4
•
VDSL2 Port Connector Pinouts, page A-4
•
ADSL2+ Port Connector Pinouts, page A-5
•
V.92 Port Connector Pinouts, page A-5
•
G.SHDSL Port Connector Pinouts, page A-6
•
Data BRI Port Connector Pinouts, page A-6
•
Voice ISDN BRI Interface Pin Numbers and Functions, page A-6
•
Cable Specifications, page A-7
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Note
For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that was shipped with the router and the Regulatory Compliance and Safety Information for
Cisco 800 Series and SOHO Series Routers.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
A-1
Appendix A
Technical Specifications
Router Specifications
Router Specifications
Table A-1 lists the system specifications for the routers.
Table A-1
Router Specifications
Description
Design Specification
Physical Dimensions
Dimensions with antenna and rubber feet
(H x W x D)
1.9 x 12.8 x 10.4 in.
Weight (not including desktop power supply) 5.5 lb (2.5 kg), maximum
Environmental Operating Ranges
Nonoperating temperature
–4 to 149°F (–20 to 65°C)
Nonoperating humidity
5 to 95% relative humidity
Nonoperating altitude
0 to 15,000 ft (4570 m)
Operating temperature
32 to 104°F (0 to 40°C)
Operating humidity
10 to 85% relative humidity
Operating altitude
0 to 10,000 ft (3000 m)
Noise criterion
NC- 33; less than or equal to 32 dBA
Router Power Adapter
Input voltage
85 to 264 VAC
Input frequency
47 to 63 Hz
Power output
60 W, maximum
Output voltages
+12 VDC
Inline Power-over-Ethernet Adapter
Input voltage
85 to 264 VAC
Input frequency
47 to 63 Hz
Power output
80 W, maximum
Output voltage
–48 VDC
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
A-2
OL-16193-03
Appendix A
Technical Specifications
Wireless Access Point
Wireless Access Point
Table A-2 lists the specifications for the wireless access point (AP).
Table A-2
Wireless Access Point Specifications
Description
Design Specification
Radio technology
IEEE 802.11n draft 2.0 standard compliant. 2x3
MIMO1 radio. Backward compatible with
802.11b/g and 802.11a (Cisco 890 series routers).
Operating frequency
Cisco 860 series and 880 series ISRs
2.4-GHz radio band
Cisco 890 series ISRs
2.4 and 5-GH radio bands
Channels
Country-specific 20 and 40 MHz
PHY Data rate
802.11b up to 11 Mb/s
802.11g up to 54 Mb/s
802.11n up to 300 Mb/s
1. Multiple Input/Multiple Output.
FE and GE Port Pinouts
Table A-3 lists the pinouts for the Ethernet ports.
Table A-3
Ethernet LAN Port Pinouts
Pin
Function
1
RX+
2
RX–
3
TX+
4
Unused
5
Unused
6
TX–
7
Unused
8
Unused
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
A-3
Appendix A
Technical Specifications
Console and Auxiliary Port Connector Pinouts
Console and Auxiliary Port Connector Pinouts
Table A-4 lists the pinouts for the console and auxiliary port connectors.
Table A-4
Console and Auxiliary Port Connector Pinouts
RJ-45 Pin
Function
1
RTS
2
DTR
3
TXD
4
GND
5
GND
6
RXD
7
DSR
8
CTS
FXS and FXO Port Connector Pinouts
Table A-6 lists the FXS and FXO connector pinouts.
Table A-5
FXS and FXO Connector Pinouts (RJ-11-to-RJ-45)
Pin
Signal
1
NC
2
NC
3
TIP
4
RING
5
NC
6
NC
VDSL2 Port Connector Pinouts
Table A-6 lists the VDSL2 connector pinouts.
Table A-6
VDSL2 Connector Pinouts (RJ-11-to-RJ-45)
RJ-11 Pin
Function
1
Unused
2
Unused
3
TIP
4
RING
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
A-4
OL-16193-03
Appendix A
Technical Specifications
ADSL2+ Port Connector Pinouts
Table A-6
VDSL2 Connector Pinouts (RJ-11-to-RJ-45) (continued)
RJ-11 Pin
Function
5
Unused
6
Unused
ADSL2+ Port Connector Pinouts
Table A-6 lists the ADSL2+ connector pinouts.
Table A-7
ADSL2+ Connector Pinouts (RJ-11)
RJ-11 Pin
Function
1
Unused
2
Unused
3
TIP
4
RING
5
Unused
6
Unused
V.92 Port Connector Pinouts
Table A-8 lists the V.92 connector pinouts.
Table A-8
V.92 Connector Pinouts (RJ-11-to-RJ-45)
RJ-11 Pin
Function
1
Unused
2
Unused
3
TIP
4
RING
5
Unused
6
Unused
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
A-5
Appendix A
Technical Specifications
G.SHDSL Port Connector Pinouts
G.SHDSL Port Connector Pinouts
Table A-9 lists the pinouts for the global industry standard symmetrical high-speed DSL (G.SHDSL)
WAN port.
Table A-9
G.SHDSL WAN Port Pinouts
Pin
Function
1
Unused
2
TIP (Port1)
3
TIP (Port0)
4
TIP (Port0)
5
TIP (Port1)
6
Unused
Data BRI Port Connector Pinouts
Table A-10 lists the pinouts for the Data BRI port.
Table A-10
Data BRI Port Pinouts
Pin
Function
1
Unused
2
Unused
3
TXP
4
RXP
5
TXN
6
TXN
7
Unused
8
Unused
Voice ISDN BRI Interface Pin Numbers and Functions
Table A-11lists the interface pin numbers and functions for the voice ISDN BRI port.
Table A-11
Interface Pin Numbers and Functions
ISDN BRI NT/TE Card
NT Interface1
TE Interface2
Pin 3/T+
Pin 3/R+
Pin 3/T+
Pin 4/R+
Pin 4/T+
Pin 4/R+
Pin 5/R-
Pin 5/T-
Pin 5/R-
Pin 6/T-
Pin 6/R-
Pin 6/T-
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
A-6
OL-16193-03
Appendix A
Technical Specifications
Cable Specifications
1. Use a straight-through cable for NT interfaces.
2. Use a crossover cable for TE interfaces.
Cable Specifications
This section provides specifications for the following Ethernet cables:
•
Straight-through cable
•
Crossover cable
Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be
used for the Ethernet LAN port.
Ethernet Cable Specifications
Table A-12 lists the specifications that apply to both straight-through and crossover Ethernet cables.
Table A-12
Ethernet Cable Specifications
Type
Category
10BASE-T
Category 3 or 5
100BASE-T
Category 5 or higher
1000BASE-T
Category 5 or higher
Maximum Cable Length
The maximum length for the Ethernet cables that connect equipment to the router is 328 feet
(100 meters). This length is also the maximum distance between the router and the equipment connected
to it.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-03
A-7
Appendix A
Technical Specifications
Cable Specifications
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
A-8
OL-16193-03